Super Nova Distortion
|
|
- Isaac Freeman
- 6 years ago
- Views:
Transcription
1 Super Nova Distortion The Super Nova is a reworking of the Marshall Guv'nor circuit. It uses the same gain structure as its parent design but is EQ'ed quite differently. The basic tone from the gain stages is a little more focused on the mid frequencies than the original. Clipping diodes are MOSFETs instead of LEDs. Finally, instead of a passive TMB tonestack there's a very responsive Baxandall tonestack. It works well with mid heavy blues rock and hard rock leads to crushing scooped thrash and death metal rhythms.. Finally the on board charge pump allows the unit to operate at 18V reducing opamp clipping and increasing head room. Pro tip: the Super Nova can be used as a standalone preamp into a power amp for live use or into a recording interface coupled with an impulse response for recording. License information Please note that the license for the Super Nova is different from most other Nucleon projects. Specifically, it is prohibited to produce commercial pedals with the Super Nova PCB. Please respect this. This project is for personal (DIY) use only. Commercial (re)selling or distribution of the PCB, its design layout or this build document is prohibited. These materials are not to be sold as part of a kit.. Construction and use of the PCB and project information is at your own risk. Nucleon FX cannot be held accountable for any damages to equipment or yourself Nucleon FX 1
2 BOM Resistors Capacitors R1 2M2 C1 22n R2 1k C2 1n R3 1M C3 100p R4 1k C n R5 10k C5 100n R6 330k C6 390p R7 22k C7 68n - 1u R8 22k C n R9 22k C9 2n2 R10 18k C10 390p R11 18k C11 100n R12 47k C12 100n R13 47k C13 100u R14 100k C14 100n MLCC CLR 3k3-10k C15 100n MLCC C16 10u C17 10u Diodes and Controls misc D1 1N5817 GAIN 100 kb D2, D3 1n914 LEVEL 100 kb Q1, Q2 2N7000 BASS 50 kb kb TREBLE 50 kb kb Opto TLP222G IC 1, IC 3 TL072 Bypass DPDT Stomp IC2 See notes 2017 Nucleon FX 2
3 Schematic 2017 Nucleon FX 3
4 NOTES IC2 This IC generates a -9V supply for the split rail design. I suggest using a socket here also. Pick one of the ICs below. I've not found a bullet proof recipe. I've had seemingly identical builds where one worked well with the 7660S while the other one needed the In other words: YMMV. Chip BST pads Comments ICL7660S Jumper with wire of 0Ω resistor Cheap and can work, sometimes induces audible high pitched whine TC1044 Jumper with wire of 0Ω resistor Use as improvement over 7660S if that generates audible whine LT1054 Leave open Best performance, highest current consumption and expensive Tone Controls The Super Nova tone control is a Baxandall type filter that consists of a Bass and Treble shelf filter. The two filters cross over in the mid frequencies, allowing a mid-cut or boost centered around 720 Hz. This is a more flexible setup than might first appear. On the maximum settings there is about 6 db of boost or cut available. This is a modest amount but ensures a useable range of the controls. R12, R13 and C10 are unusual additions to the standard Baxandall. They help control the boost on the outer limits of the shelfs by squashing the boost on frequencies below 80 Hz and progressively lowering the boost above 3.5 khz. This again results in a more useable range of the controls, keeping mush and fizz in check. It also increases stability of the circuit, preventing stressing out the opamp. You may choose to omit them. Using 50k pots give a maximum boost of about 6.5 db at the outer frequencies of the range. A 100k pot add another 3 db or so to that if you need it. C4 and C7, 11, 12 The suggested value for C4 is either 270n or 330n, which corresponds to 590 Hz and 482 Hz respectively as the bass roll off frequency for the first amplification stage. Both work well, adjust to taste. Paradoxically, if you tune your guitar down a lot, a higher roll off frequency can keep things tight instead of muddy. C7, C11 and C12 can really be any cap value high enough to pass all frequencies. I suggest 68n for C7 and 100n or higher for C11 and C12. The exact value doesn't matter that much, so don't fret if you haven't got everything in stock. Substitutes up to 1 uf will work fine. Board Mounted Pots Use board mounted pots and tag them to the PCB by soldering only one leg at first. Fit the PCB to the enclosure and solder the remaining legs. Then reflow the first leg to relieve any tension from it. Put some thick double sided tape on the back for isolation Nucleon FX 4
5 Capacitor types I roughly follow these guidelines for capacitor size when designing the PCB: smaller than 1nF: Multi Layer Ceramic (MLCC) for filtering smaller than 1nF: WIMA box caps in audio path 1nF - 10nF: Whatever I have around, usually 'greenies' or MKP box caps 10n - 1u: Panasonic ECQ-V in audio path 100n - 1u: MLCC for power filtering1u - 470u: Electrolytics This is mostly due to what's available in my personal stock. You can deviate from this. The only exception is the use of MLCC caps for filtering power lines. These do a better job than film caps. Wiring JI - tip of input jack JO - tip of output jack G - sleeve of output jack SW1 - center pad to center lug Outer pads to outer lugs 9V - sleeve of power jack G2 - center of power jack SW2 - one pad to centerlug Other pad to outer lug (one lug unused) Bypass DPDT Two sets of three ( and ) corresponding to columns on a DPDT switch. 1 and 4: top lug 2 and 5: center lug 3 and 6: bottom lug 2017 Nucleon FX 5
6 Drill Template Cover a 1590B in painters tape. Print this page at 100% scale and stick the template on top of the tape with some glue or tape. Double check alignment with the PCB before drilling. Drill the pot holes with a diameter 8 mm (one size larger than required) so you have some wiggle room. [Drill template coming soon] 2017 Nucleon FX 6
Blues King. FX TYPE: Overdrive Images VFE and MBP Project Doc madbeanpedals W x H
Blues King FX TYPE: Overdrive Images VFE and MBP Project Doc madbeanpedals 2.17 W x 2.025 H Note: Use the values listed on the image above not the values indicated on the silk-screen of the PCB. Some values
More informationJour de FET Mounting instructions.
Jour de FET Mounting instructions. Summary Important notice. What's in the kit? What you'll need. Soldering on the pcb. Wiring the pedal. Test the board. Debugging chapter. Hacks!!! 3 4 4 3 5 6 Copyright
More informationRangemaster Treble Booster Kit Building Manual
Rangemaster Treble Booster Kit Building Manual Effect Pedal Kits: Rangemaster Treble Booster The Dallas Rangemaster is the most famous treble booster effect pedal, and it was the first pedal of its kind.
More informationLunarBlast v1.0. Optical Tremolo. Description:
LunarBlast v1.0 Optical Tremolo Description: Based on the venerable DIY Tremulus Lune classic circuit, www.madbean.com forum member CultureJam created this awesome sounding tremolo dubbed the Shoot the
More informationFREEKOUT FX TYPE: Ring Modulator Based on the EHX Frequency Analyzer 2015 madbeanpedals
FREEKOUT FX TYPE: Ring Modulator Based on the EHX Frequency Analyzer 2015 madbeanpedals 2.3 W x 3.025 H This project requires an 18v 100mA (or more) center tip negative power supply. I recommend the Dunlop
More informationMobius Strip. FX TYPE: Dual Delay Images VFE and MBP Project Doc madbeanpedals W x H
Mobius Strip FX TYPE: Dual Delay Images VFE and MBP Project Doc madbeanpedals 2.17 W x 2.025 H Note: Use the values listed on the image above not the values indicated on the silk-screen of the PCB. Some
More informationBuild Guide CascadiA. GeFet Preamp
Build Guide CascadiA GeFet Preamp Disclaimery stuff: This project is meant to be assembled by fellow DIYers from the Madbean forum and should only be used for the forces of good. Any other uses prohibited
More informationTriumvirate. FX TYPE: Multi-Band Distortion Images VFE and MBP Project Doc madbeanpedals W x 2.01 H
Triumvirate FX TYPE: Multi-Band Distortion Images VFE and MBP Project Doc madbeanpedals 2.17 W x 2.01 H Note: Use the values listed on the image above not the values indicated on the silk-screen of the
More informationNEW WAVE CV GENERATOR Build Document last updated september 2017 for PCB version 1.0
NEW WAVE CV GENERATOR Build Document last updated september 2017 for PCB version 1.0 The New Wave is a Control Voltage Generator. It has two LFO's (low frequency oscillators) and four different output
More informationGlue Fuzz Mounting instructions.
Glue Fuzz Mounting instructions. Index Important notice. 2 What's in the kit? 3 What you'll need. 4 Soldering on the pcb. 4 Wiring the pedal. 11 Test the board. 12 Debugging chapter. 13 Copyright Zorg
More informationMultiwave. Guitar Synthesizer. Build Document last updated november 2018 Version
Multiwave Guitar Synthesizer Build Document last updated november 2018 Version 1.0 2018 The Multiwave is a guitar controlled oscillator with 3 different waveshapes: saw, triangle and square. Combined,
More informationBuild Your Own Clone Crown Jewel Kit Instructions
Build Your Own Clone Crown Jewel Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationTWIN PEAKS TREMOLO. Build Guide for v3.1
TWIN PEAKS TREMOLO Build Guide for v3.1 Revision 3.1 David Rolo 2017 Reference Quantity Value Description Switches Multiplier 1 1 pole 6 pos. rotary switch Shape 1 1 pole 8 pos. rotary switch Trem Type
More informationElectric Druid 4 second Digital Delay Project
Electric Druid 4 second Digital Delay Project Overview! 2 Build Instructions! 2 Populate the PCB! 2 Resistors! 2 Cup of tea and soldering check! 3 Power protection diode! 4 Ground link wire! 4 IC sockets!
More informationGuitarpedalkits.com Overdrive Pedal Build Instructions
Page 1 Guitarpedalkits.com Overdrive Pedal Build Instructions Follow the instructions in this guide to build your very own DIY overdrive pedal from GuitarPedalKits.com. If you re a first time builder,
More informationUltimatum Fuzz. The Ultimate experience in vintage-style octave-up fuzz
Ultimatum Fuzz The Ultimate experience in vintage-style octave-up fuzz Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts
More informationStandard JFET input buffer and Standard NPN Output buffer
Board Standard JFET input buffer and Standard NPN Output buffer By PCB Guitar mania Mania Project link The buffers are normally added into a circuit to prevent loading and loss of definition of the guitar
More informationBuild Your Own Clone Silver Pony 2 Kit Instructions
Build Your Own Clone Silver Pony 2 Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationINTO THE UNKNOWN Build Document last updated may 2016 Version
INTO THE UNKNOWN Build Document last updated may 2016 Version 1.0 2015 'Into the Unknown Guitar Synthesizer Deluxe' is a CMOS based fuzz centered around the CD4046 PLL (phase locked loop) chip and a CD4015
More informationTotal Recall FX Type: Delay Based on the EHX Deluxe Memory Man 2015 madbeanpedals
Total Recall FX Type: Delay Based on the EHX Deluxe Memory Man 2015 madbeanpedals 3.34" W x 3.875" H Terms of Use: You are free to use purchased Total Recall circuit boards for both DIY and small commercial
More informationTHE GREEN CURRANT TREMOLO Build Document last updated june 2017 for PCB version 1.5
THE GREEN CURRANT TREMOLO Build Document last updated june 2017 for PCB version 1.5 The Green Currant tremolo is a very percussive and vibey tremolo based around the TDA7052A amplifier chip. It splits
More informationAxis Fuzz Kit Building Manual
Axis Fuzz Kit Building Manual Effect Pedal Kits: Axis Fuzz The Axis Fuzz Kit is based in the Roger Mayer Axis Fuzz, the effect pedal responsible for Jimi Hendrix sound in Axis Bold As Love. What else is
More informationDirtbaby FX TYPE: Delay Based on the EHX DMM 2016 madbeanpedals
Dirtbaby FX TYPE: Delay Based on the EHX DMM 2016 madbeanpedals 3.325 W x 2.325 H Terms of Use: You are free to use purchased circuit boards for both DIY and small commercial operations. You may not offer
More informationBlueprint. FX TYPE: Delay Images VFE and MBP Project Doc madbeanpedals W x H
Blueprint FX TYPE: Delay Images VFE and MBP Project Doc madbeanpedals 2.17 W x 2.025 H Note: Use the values listed on the image above not the values indicated on the silk-screen of the PCB. Some values
More informationGuitarPCB.com Angry Red Camel Build Instructions
GuitarPCB.com Angry Red Camel Build Instructions Board Dimensions (W x H) 1.95 x 1.65 inches, i.e.: 49.5 x 41.9mm. This design will fit into a 1290NS/1590B size enclosure or larger. This is a variant of
More informationGCI BRUTALIST JR. BUILD GUIDE
GCI BRUTALIST JR. BUILD GUIDE The Brutalist Jr. is the DIY little brother to the GCI Brutalist, a high powered distortion pedal loosely based on the Providence Stampede SDT-1. It runs on 9v DC power or
More informationBuild Your Own Clone Silver Pony Kit Instructions
Build Your Own Clone Silver Pony Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationFX Type: Distortion 1.95 W x H Terms of Use: Slow Loris Slow Loris
Slow Loris 2015 edition madbeanpedals FX Type: Distortion Based on the ProCo Rat Changes for the 2015 edition: Slight layout adjustments. No circuit changes. Previous version: http://www.madbeanpedals.com/projects/slowloris/docs/slowloris.zip
More informationBuild Your Own Clone Chancellor Kit Instructions
Build Your Own Clone Chancellor Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationPCB by 1776 Effects/JRM 2013 Circuit Design by Jon Patton
Cardinal Tremolo PCB by 1776 Effects/JRM 2013 Circuit Design by Jon Patton The Cardinal Tremolo is a transistor and vactrol implementation of the Harmonic Tremolo. It resembles the harmonic tremolo from
More informationAquaboy FX TYPE: Delay Based on the Boss DM madbeanpedals
Aquaboy FX TYPE: Delay Based on the Boss DM-2 2016 madbeanpedals 2.3 W x 3.125 H 1.29.17 Correction see page 6. Note: the M pad by the Delay pot is for modulation control (see the AB_MOD documentation
More informationBuild Your Own Clone British Blues Overdrive Kit Instructions
Build Your Own Clone British Blues Overdrive Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free
More informationStage Fright 2015 edition FX TYPE: Phaser Based on the Maestro Phaser 2015 madbeanpedals
Stage Fright 2015 edition FX TYPE: Phaser Based on the Maestro Phaser 2015 madbeanpedals 2.3" W x 3.45" H Previous Version: http://www.madbeanpedals.com/stagefright/stagefright.zip Terms of Use: You are
More informationGuitarPCB.com Presents. Fuzzy Bee v2 (Pump d Up Edition) Build Instructions
GuitarPCB.com Presents Fuzzy Bee v2 (Pump d Up Edition) Build Instructions Board Dimensions (W x H) 2.13 x 1.67 i.e.: 54.0mm x 42.4mm. This design will fit into a 1290NS/1590B size enclosure or larger.
More informationBuild Your Own Clone B.G. Fuzz Kit Instructions
Build Your Own Clone B.G. Fuzz Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationMono Amplifier. LM386 Headphone Amp
Mono Amplifier LM386 Headphone Amp Layout On/Off Switch - cuts power to the circuit Mono Input Jack: use either L or R or solder together Schematic Step 1 - Parts List 1.) R1-10ohm Resistor - Brown Black
More informationBuild instructions for the BLÜE MONSTER Dual band FET OD diy kit!
Blue Monster, v.1.11... 1(11) Build instructions for the BLÜE MONSTER Dual band FET OD diy kit! Thanx for getting your hands on the BLÜE MONSTER diy kit! In a near future you will have some fun building
More informationElectric Druid Flangelicious Flanger Project
Electric Druid Flangelicious Flanger Project (Using either 4KNOBFLANGE or MULTIFLANGE chips) Overview! 2 Build Instructions! 2 Populate the PCB! 2 1N4148 Diodes! 2 Resistors! 2 Cup of tea and soldering
More informationBuild Your Own Clone 27V Boost Kit Instructions
Build Your Own Clone 27V Boost Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationBuild Your Own Clone Mouse Kit Instructions
Build Your Own Clone Mouse Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect. Soldering,
More informationBMC017. 2LFOSH Last updated I Features II Schematics III Construction
BMC017. 2LFOSH Last updated 12-3-2013 I Features II Schematics III Construction I. Features The 2LFOSH module is a combination of three different modules on one board, designed to be easy to be easy to
More informationMoWAH v3. Board Dimensions (W x H) 2.05 x 1.95 ca. 52.1mm x 49.6mm
MoWAH v3 Board Dimensions (W x H) 2.05 x 1.95 ca. 52.1mm x 49.6mm The above image can be downloaded from http://i647.photobucket.com/albums/uu198/tonmann/guitarpcb%20boards/mowahv3layout.png Printing at
More informationD Lay by GuitarPCB. We also carry the D'lay Tap Tempo board available separately in our SHOP. Not mandatory.
D Lay by GuitarPCB Based on an Analog Style Delay but with added Delay time of up to 350-400ms, or slightly longer depending on quality of the PT2399 chip you use. Many months and trials went into perfecting
More informationUK-electronic 2014 Manual Kit Plexiclone V1.1
UK-electronic 0 Manual Kit Plexiclone V. Page...Basics Page...BOM Page...Soldering the pcb Page...Inside of a building device Page 7 External wiring, notes Page 8...Mechanical tips Page.Drill template,
More informationSTEP 0 Prepare the Materials.
How to Build a Germanium Fuzz Guitar Effect. This document will guide you to build and test your Germanium Fuzz guitar pedal. With all the materials on hand, it takes around 2-4 hours to build it. Try
More informationThe Engineer s Thumb Compressor/Limiter ValveWizard PCB User Guide (Issue 3 PCBs)
The Engineer s Thumb Compressor/Limiter ValveWizard PCB User Guide (Issue 3 PCBs) Fig. 1: Circuit schematic Fig. 2: Component layout Fig. 3: Wiring diagram (with millennium bypass) Before populating the
More informationBuild Your Own Clone Reverb Kit Instructions
Build Your Own Clone Reverb Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect. Soldering,
More informationBuild Your Own Clone Analog Chorus Kit Instructions
Build Your Own Clone Analog Chorus Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationBuild Your Own Clone The Swede Kit Instructions
Build Your Own Clone The Swede Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationBuild Your Own Clone Classic Overdrive Kit Instructions
Build Your Own Clone Classic Overdrive Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of
More informationBuild Your Own Clone Green Pony Kit Instructions
Build Your Own Clone Green Pony Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationValue Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
More informationVFE Choral Reef. FX TYPE: Chorus Images VFE and MBP Project Doc madbeanpedals Aug. 2 nd update see pg W x 2.05 H
VFE Choral Reef FX TYPE: Chorus Images VFE and MBP Project Doc madbeanpedals Aug. 2 nd update see pg.4 2.17 W x 2.05 H Terms of Use: These projects are intended for DIY use only and may not be used in
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationDig Dug madbeanpedals FX Type: Sequencer W x 3.25 H
Dig Dug2 2015 madbeanpedals FX Type: Sequencer 4.15 W x 3.25 H B.O.M. Resistors Caps Diodes R1 1M C1 100n D1 1N5817 R2 1M C2 220n D2 - D4 1n914 R3 10k C3 15n LED1-8 3mm Red R4 330k C4 2n2 PATT 3mm Red
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More informationBuild Your Own Clone Li l Echo Kit Instructions
Build Your Own Clone Li l Echo Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationNever power this piano with anything other than a standard 9V battery!
Welcome to the exciting world of Digital Electronics! Who is this kit intended for? This kit is intended for anyone from ages 13 and above and assumes no previous knowledge in the field of hobby electronics.
More informationRaygun. Vector Weapon. projects. Raygun vector weapon. Build a mini analog sound-effects circuit. By Symetricolour. Time: 2 4 hours CosT: $15 $20
projects Raygun vector weapon Raygun Vector Weapon By Symetricolour Time: 2 4 hours CosT: $5 $20 Build a mini analog sound-effects circuit. Gregory Hayes 02 Materials» raygun Vector Weapon Kit item #MSVWP
More informationVFE Switching Board madbeanpedals Some images 2017 VFE Pedals, used with permission 8.7 update: see pg W x 1.33 H
VFE Switching Board 2017 madbeanpedals Some images 2017 VFE Pedals, used with permission 8.7 update: see pg. 7 2.16 W x 1.33 H The VFE Switching Board and micro-controller are included with all the VFE
More informationVOLUME AND TONE CONTROL - PREAMPLIFIER K8084
VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control H8084IP-1 Features & specifications When
More informationStarving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24
SS2 guide Written By: 6L6 2019 guides.diyaudio.com/ Page 1 of 24 INTRODUCTION This is a build guide for the hybrid headphone/pre-amplifier. You can buy a kit at the SSII product listing on the diyaudio
More informationU-RETRO 4 KNOB DELUXE
U-RETRO 4 KNOB DELUXE Active/Passive Preamp for Bass Guitars The U-RETRO 01 4 KNOB DELUXE, based on the J-RETRO 01, is a universal highly flexible on-board preamp and EQ system. The standard pots have
More informationSPRING REVERB datasheet ver. 17/01/17
SPRING REVERB datasheet ver. 17/01/17 www.op-electronics.com Printing error: last datasheet revision contained a mistake about the value of C5 capacitor, the cap value should be 680p and not 47n. This
More informationFM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Build Instructions Before you start, take
More informationPresenting a simple, versatile phono stage using a bare minimum number of parts and the following features:
1 van 5 24-3-2007 22:26 The VSPS Very Simple Phono Stage Presenting a simple, versatile phono stage using a bare minimum number of parts and the following features: 27 parts per stereo unit. Low parts
More informationN3ZI Kits General Coverage Receiver, Assembly & Operations Manual (For Jun 2011 PCB ) Version 3.33, Jan 2012
N3ZI Kits General Coverage Receiver, Assembly & Operations Manual (For Jun 2011 PCB ) Version 3.33, Jan 2012 Thank you for purchasing my general coverage receiver kit. You can use the photo above as a
More informationWeener Wah FX TYPE: Wah Wah Based on the Clyde McCoy 2016 edition madbeanpedals
Weener Wah FX TYPE: Wah Wah Based on the Clyde McCoy 2016 edition madbeanpedals 1.95 W x 2.275 H Terms of Use: You are free to use purchased WeenerWah circuit boards for both DIY and small commercial operations.
More informationAUDIO PROBE EXPLAINED
AUDIO PROBE EXPLAINED An Audio Probe is an essential tool for the DIY pedal builder. This along with a test box, are tools you should have at your disposal for easier debugging when things go wrong! They
More informationBYOC Vibrato Kit Instructions BA662A version
BYOC Vibrato Kit Instructions BA662A version Please read these instructions very thoroughly before building even if you are an experience builder. Because of the layout, there is a certain order which
More informationBuild Your Own Clone Classic Phaser Kit Instructions
Build Your Own Clone Classic Phaser Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationChunky Cheese Build Guide Rev
Chunky Cheese Build Guide Rev. 2008-08-04 The Chunky Cheese is a slightly-modified version of the discontinued Big Cheese fuzz pedal. Table of Contents Table of Contents... 1 PCB Layout... 2 Parts List...
More informationVFE Merman. FX TYPE: Overdrive Images VFE and MBP Project Doc madbeanpedals W x H
VFE Merman FX TYPE: Overdrive Images VFE and MBP Project Doc madbeanpedals 2.17 W x 2.025 H Note: Use the values listed on the image above not the values indicated on the silk-screen of the PCB. Some values
More informationpresents FX TYPE: VIBRATO m2011 madbeanpedals Release date: revised see highlighted notes Thanks, Paul!
http://www.madbeanpedals.com presents Quadrovibe FX TYPE: VIBRATO m2011 madbeanpedals Release date: 07.1.11 revised 10.26 see highlighted notes Thanks, Paul! The Quadrovibe is a unique Vibrato/Tremolo
More informationBYOC Vibrato Kit Instructions BA6110 version
BYOC Vibrato Kit Instructions BA6110 version Please read these instructions very thoroughly before building even if you are an experience builder. Because of the
More informationBuild Your Own Clone Li l Reverb Kit Instructions
Build Your Own Clone Li l Reverb Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationBuild Your Own Clone Li l Pony Kit Instructions
Build Your Own Clone Li l Pony Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationSimple LFO Features. 2. Application. 3. Description. Simple and easy to build LFO module for Analog Synthesizers.
Simple LFO. Simple and easy to build LFO module for Analog Synthesizers.. Features Square and Triangle waveforms (90 phase shifted) Dual range frequencies Frequency ranges from under Hz up to several khz
More informationJason Stull. Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010
Jason Stull Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010 1 Introduction My original idea for a class project was to build a tube guitar amplifier. I have wanted a tube amp for some
More informationWiring Manual NEScaf April 2010 (August 2006)
Wiring Manual NEScaf April 2010 (August 2006) Switched Capacitor Audio Filter The NEScaf is a switched capacitor audio filter (acronym SCAF) built around a building-block type filter chip. The NEScaf will
More informationWARNING / DISCLAIMER
WARNING / DISCLAIMER PLEASE READ THE FOLLOWING BEFORE PURCHASING OR BUILDING THIS PROJECT!. NO DIRECT TECHNICAL SUPPORT: This project has been verified to be working, and I have done my best to provide
More informationBuild Your Own Clone Kuzco Jr. Kit Instructions
Build Your Own Clone Kuzco Jr. Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationDIY Function Generator XR2206
DIY Function Generator XR2206 20Hz 100KHz http://radiohobbystore.com Components List: Resistors: R1, R2 1% Metal Film 5K1 R4 1% Metal Film 10K R5 1% Metal Film 3K R10 5% Carbon Film 10R R3, R9 Potentiometer
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationBuild Your Own Clone Parametric Multi-Band Compressor Kit Instructions
Build Your Own Clone Parametric Multi-Band Compressor Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning
More informationIPR LA-3 KIT last update 15 march 06
IPR LA-3 KIT last update 15 march 06 PART-2: Audio Circuitry CIRCUIT BOARD LAYOUT: Power and Ground Distribution Now that your power supply is functional, it s time to think about how that power will be
More informationAnalog Effect Pedals. EE333 Project 1. Francisco Alegria and Josh Rolles
Analog Effect Pedals EE333 Project 1 Francisco Alegria and Josh Rolles Introduction For the first project, we ve chosen to design two analog guitar effect pedals. This report will discuss the schematic
More information30 Watt Audio Power Amplifier
30 Watt Audio Power Amplifier Including Preamp, Tone Controls, Reg dc Power Supply, 18 Watt into 8 Ohm - 30W into 4 Ohm loads Amplifier Section Circuit diagram: Audio Power Amplifier Circuit Diagram This
More informationBuild Your Own Clone Li l Analog Chorus Kit Instructions
Build Your Own Clone Li l Analog Chorus Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free
More informationCave Dweller 2015 edition FX Type: Delay 2015 madbeanpedals
Cave Dweller 2015 edition FX Type: Delay 2015 madbeanpedals 1.3" W x 1.975" H (main board) Previous Version: http://www.madbeanpedals.com/projects/cavedweller/cavedweller_drill.zip Terms of Use: You are
More informationPenrose Quantizer Assembly Guide
Penrose Quantizer Assembly Guide Schematic and BOM The schematic can be found here: www.sonic-potions.com/public/penrosequantizerschematic.pdf The BOM is available at google docs: Link to BOM Prepare the
More informationTHE ZEN TRIODE EXPIREMENTERS AMPLIFIER KIT MODEL SE84CDIYMONO
THE ZEN TRIODE EXPIREMENTERS AMPLIFIER KIT MODEL SE84CDIYMONO ASSEMBLY INSTRUCTIONS 2008 The circuit board has been designed to be used in 2 ways; A) Mounted on stand-offs to a piece of wood and B) Mounted
More informationBuild Your Own Clone Li l Comp Kit Instructions
Build Your Own Clone Li l Comp Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationJCM W GUITAR AMPLIFIER. User s Manual
JCM 800 2203 100W GUITAR AMPLIFIER User s Manual 1 Thank you for the purchase of your Ceriatone guitar amplifier! Here, we hope to explain how best to use your new amp. Table of Contents 1) About the 2203..
More informationBuild Your Own Clone Mega Chorus & Vibrato Kit Instructions
Build Your Own Clone Mega Chorus & Vibrato Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free
More informationSwitcher Assembly guide. Switcher Assembly guide 1. Soldering. 2. Switcher3 vs Switcher2. 3. PCB split.
Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about safely handling
More informationBuild Your Own Clone Spring Reverb Kit Instructions
Build Your Own Clone Spring Reverb Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationSlow Century Build Guide
Slow Century Build Guide In 1986, Michael Soldano founded an amp company in Los Angeles. Known for high-gain designs, Soldano has produced a number of amps that have been critical successes with a huge
More informationJCM W GUITAR AMPLIFIER. User s Manual
JCM 800 2204 50W GUITAR AMPLIFIER User s Manual 1 Thank you for the purchase of your Ceriatone guitar amplifier! Here, we hope to explain how best to use your new amp. Table of Contents 1) About the 2204..
More informationTS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More information