UC3842/UC3843/UC3844/UC3845

Size: px
Start display at page:

Download "UC3842/UC3843/UC3844/UC3845"

Transcription

1 UC3842/UC3843/UC3844/UC3845 SMPS Controller Features Low Start up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency up to 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequencycurrent-mode PWM controller. They are specially designed for Off-Line and DC to DC converter applications with minimum external components. These integrated circuits feature a trimmed oscillator for precise duty cycle control, a temperature compensated reference, high gain error amplifier, current sensing comparator and a high current totempole output for driving a Power MOSFET. The UC3842 and UC3844 have UVLO thresholds of 16V (on) and 10V (off). The UC3843 and UC3845 are 8.5V(on) and 7.9V (off). The UC3842 and UC3843 can operate within 100% duty cycle. The UC3844 and UC3845 can operate with 50% duty cycle. 8-DIP 8-SOP 1 14-SOP 1 1 Internal Block Diagram * NORMALLY 8DIP/8SOP PIN NO. * ( ) IS 14SOP PINNO. * TOGGLE FLIP FLOP USED ONLY IN UC3844, UC3845 Rev Fairchild Semiconductor Corporation

2 UC3842/UC3843/UC3844/UC3845 Absolute Maximum Ratings Parameter Symbol Value Unit Supply Voltage VCC 30 V Output Current IO ±1 A Analog Inputs (Pin 2.3) V(ANA) -0.3 to 6.3 V Error Amp Output Sink Current ISINK (E.A) 10 ma Power Dissipation at TA 25 C (8DIP) PD(Note1,2) 1200 mw Power Dissipation at TA 25 C (8SOP) PD(Note1,2) 460 mw Power Dissipation at TA 25 C (14SOP) PD(Note1,2) 680 mw Storage Temperature Range TSTG -65 ~ +150 C Lead Temperature (Soldering, 10sec) TLEAD +300 C Note: 1. Board Thickness 1.6mm, Board Dimension 76.2mm 114.3mm, (Reference EIA / JSED51-3, 51-7) 2. Do not exceeed PD and SOA (Safe Operation Area) Power Dissipation Curve POWER DISSIPATION (mw) DIP 14SOP 8SOP AMBIENT TEMPERATURE ( ) Thermal Data Characteristic Symbol 8-DIP 8-SOP 14-SOP Unit Thermal Resistance Junction-ambient Rthj-amb(MAX) C/W Pin Array 8DIP,8SOP 14SOP COMP 1 8 VREF COMP 1 14 VREF VFB 2 7 VCC N/C 2 13 N/C CURRENT SENSE 3 6 OUTPUT VFB 3 12 VCC RT/CT 4 5 GND N/C 4 11 PWR VC CURRENT SENSE 5 10 OUTPUT N/C 6 9 GND RT/CT 7 8 PWR GND 2

3 UC3842/UC3843/UC3844/UC3845 Electrical Characteristics (VCC=15V, RT=10kΩ, CT=3.3nF, TA= 0 C to +70 C, unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit REFERENCE SECTION Reference Output Voltage VREF TJ = 25 C, IREF = 1mA V Line Regulation VREF 12V VCC 25V mv Load Regulation VREF 1mA IREF 20mA mv Short Circuit Output Current ISC TA = 25 C ma OSCILLATOR SECTION Oscillation Frequency f TJ = 25 C khz Frequency Change with Voltage f/ VCC 12V VCC 25V % Oscillator Amplitude VOSC VP-P ERROR AMPLIFIER SECTION Input Bias Current IBIAS µa Input Voltage VI(E>A) Vpin1 = 2.5V V Open Loop Voltage Gain GVO 2V VO 4V (Note3) db Power Supply Rejection Ratio PSRR 12V VCC 25V (Note3) db Output Sink Current ISINK Vpin2 = 2.7V, Vpin1 = 1.1V ma Output Source Current ISOURCE Vpin2 = 2.3V, Vpin1 = 5V ma High Output Voltage VOH Vpin2 = 2.3V, RL = 15kΩ to GND V Low Output Voltage VOL Vpin2 = 2.7V, RL = 15kΩ to Pin V CURRENT SENSE SECTION Gain GV (Note 1 & 2) V/V Maximum Input Signal VI(MAX) Vpin1 = 5V(Note 1) V Power Supply Rejection Ratio PSRR 12V VCC 25V (Note 1,3) db Input Bias Current IBIAS µa OUTPUT SECTION Low Output Voltage VOL ISINK = 20mA V ISINK = 200mA V High Output Voltage ISOURCE = 20mA V VOH ISOURCE = 200mA V Rise Time tr TJ = 25 C, CL= 1nF (Note 3) ns Fall Time tf TJ = 25 C, CL= 1nF (Note 3) ns UNDER-VOLTAGE LOCKOUT SECTION Start Threshold UC3842/UC V VTH(ST) UC3843/UC V Min. Operating Voltage UC3842/UC V VOPR(MIN) (After Turn On) UC3843/UC V 3

4 UC3842/UC3843/UC3844/UC3845 Electrical Characteristics (Continued) (VCC=15V, RT=10kΩ, CT=3.3nF, TA= 0 C to +70 C, unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit PWM SECTION Max. Duty Cycle D(Max) UC3842/UC % D(Max) UC3844/UC % Min. Duty Cycle D(MIN) % TOTAL STANDBY CURRENT Start-Up Current IST ma Operating Supply Current ICC(OPR) Vpin3=Vpin2=ON ma Zener Voltage VZ ICC = 25mA V Adjust VCC above the start threshould before setting at 15V Note: 1. Parameter measured at trip point of latch 2. Gain defined as: V A = pin1,0 Vpin3 0.8V V pin3 3. These parameters, although guaranteed, are not 100 tested in production. UC3842 Figure 1. Open Loop Test Circuit High peak currents associated with capacitive loads necessitate careful grounding techniques Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5kΩ potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3. 4

5 UC3842/UC3843/UC3844/UC3845 UC3842/44 UC3843/45 Figure 2. Under Voltage Lockout During Under-Voltage Lock-Out, the output driver is biased to a high impedance state. Pin 6 should be shunted to ground with a bleeder resistor to prevent activating the power switch with output leakage current. Figure 3. Error Amp Configuration Peak current (IS) is determined by the formula: 1.0V I S ( MAX) = R S Figure 4. Current Sense Circuit A small RC filter may be required to suppress switch transients. 5

6 UC3842/UC3843/UC3844/UC3845 Figure 5. Oscillator Waveforms and Maximum Duty Cycle Oscillator timing capacitor, CT, is charged by VREF through RT and discharged by an internal current source. During the discharge time, the internal clock signal blanks the output to the low state. Selection of RT and CT therefore determines both oscillator frequency and maximum duty cycle. Charge and discharge times are determined by the formulas: tc = 0.55 RT CT R T 2.7 t D = R T C T I n R T 4 Frequency, then, is: f=(tc + td) -1 ForRT > 5KΩ, f= R T C T Figure 6. Oscillator Dead Time & Frequency Figure 7. Timing Resistance vs Frequency (Deadtime vs CT RT > 5kΩ) Figure 8. Shutdown Techniques 6

7 UC3842/UC3843/UC3844/UC3845 Shutdown of the UC3842 can be accomplished by two methods; either raise pin 3 above 1V or pull pin 1 below a voltage two diode drops above ground. Either method causes the output of the PWM comparator to be high (refer to block diagram). The PWM latch is reset dominant so that the output will remain low until the next clock cycle after the shutdown condition at pins 1 and/or 3 is removed. In one example, an externally latched shutdown may be accomplished by adding an SCR which will be reset by cycling VCC below the lower UVLO threshold. At this point the reference turns off, allowing the SCR to reset. UC3842/UC3843 Figure 9. Slope Compensation A fraction of the oscillator ramp can be resistively summed with the current sense signal to provide slope compensation for converters requiring duty cycles over 50%. Note that capacitor, CT, forms a filter with R2 to suppress the leading edge switch spikes. Temperature ( C) Figure 10. Temperature Drift (Vref) Temperature ( C) Figure 11. Temperature Drift (Ist) Temperature ( C) Figure 12. Temperature Drift (Icc) 7

8 ELECTRICAL CHARACTERISTICS: UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 Unless otherwise stated, these specifications apply for -55 C TA 125 C for the UC184X; -40 C TA 85 C for the UC284X; 0 C TA 70 C for the 384X; V CC = 15V (Note 5); RT = 10k; CT = 3.3nF, TA=TJ. UC1842/3/4/5 UC3842/3/4/5 UNITS PARAMETER TEST CONDITIONS UC2842/3/4/5 MIN TYP MAX MIN TYP MAX Reference Section Output Voltage TJ = 25 C, I O = 1mA V Line Regulation 12 VIN 25V mv Load Regulation 1 I0 20mA mv Temp. Stability (Note 2) (Note 7) mv/ C Total Output Variation Line, Load, Temp. (Note 2) V Output Noise Voltage 10Hz f 10kHz, TJ = 25 C (Note2) µv Long Term Stability TA = 125 C, 1000Hrs. (Note 2) mv Output Short Circuit ma Oscillator Section Initial Accuracy TJ = 25 C (Note 6) khz Voltage Stability 12 VCC 25V % Temp. Stability TMIN TA TMAX (Note 2) 5 5 % Amplitude VPIN 4 peak to peak (Note 2) V Error Amp Section Input Voltage VPIN 1 = 2.5V V Input Bias Current µa AVOL 2 VO 4V db Unity Gain Bandwidth (Note 2) TJ = 25 C MHz PSRR 12 VCC 25V db Output Sink Current VPIN 2 = 2.7V, VPIN 1 = 1.1V ma Output Source Current VPIN 2 = 2.3V, VPIN 1 = 5V ma VOUT High VPIN 2 = 2.3V, RL = 15k to ground V VOUT Low VPIN 2 = 2.7V, RL = 15k to Pin V Current Sense Section Gain (Notes 3 and 4) V/V Maximum Input Signal VPIN 1 = 5V (Note 3) V PSRR 12 V CC 25V (Note 3) (Note 2) db Input Bias Current µa Delay to Output VPIN 3 = 0 to 2V (Note 2) ns Note 2: These parameters, although guaranteed, are not 100% tested in production. Note 3: Parameter measured at trip point of latch with VPIN 2 =0. Note 4: Gain defined as VPIN 1 A = VPIN V VPIN 3, Note 5: Adjust VCC above the start threshold before setting at 15V. Note 6: Output frequency equals oscillator frequency for the UC1842 and UC1843. Output frequency is one half oscillator frequency for the UC1844 and UC1845. Note 7: Temperature stability, sometimes referred to as average temperature coefficient, is described by the equation: VREF ( max) VREF ( min) Temp Stability = TJ ( max) TJ ( min) VREF (max) and VREF (min) are the maximum and minimum reference voltages measured over the appropriate temperature range. Note that the extremes in voltage do not necessarily occur at the extremes in temperature. 3

9 UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for 55 C TA 125 C for the UC184X; 40 C TA 85 C for the UC284X; 0 C TA 70 C for the 384X; V CC = 15V (Note 5); RT = 10k; CT = 3.3nF, TA=TJ. UC1842/3/4/5 UC3842/3/4/5 UNITS PARAMETER TEST CONDITION UC2842/3/4/5 MIN TYP MAX MIN TYP MAX Output Section Output Low Level ISINK = 20mA V ISINK = 200mA V Output High Level ISOURCE = 20mA V ISOURCE = 200mA V Rise Time TJ = 25 C, C L = 1nF (Note 2) ns Fall Time TJ = 25 C, C L = 1nF (Note 2) ns Under-voltage Lockout Section Start Threshold X842/ V X843/ V Min. Operating Voltage X842/ V After Turn On X843/ V PWM Section Maximum Duty Cycle X842/ % X844/ % Minimum Duty Cycle 0 0 % Total Standby Current Start-Up Current ma Operating Supply Current VPIN 2 = VPIN 3 = 0V ma VCC Zener Voltage ICC = 25mA V Note 2: These parameters, although guaranteed, are not 100% tested in production. Note 3: Parameter measured at trip point of latch with VPIN 2 =0. Note 4: VPIN 1 Gain defined as: A = VPIN V VPIN Note 5: Adjust VCC above the start threshold before setting at 15V. Note 6: Output frequency equals oscillator frequency for the UC1842 and UC1843. Output frequency is one half oscillator frequency for the UC1844 and UC1845. ERROR AMP CONFIGURATION Error Amp can Source or Sink up to 0.5mA 4

10 UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 UNDER-VOLTAGE LOCKOUT During under-voltage lock-out, the output driver is biased to sink minor amounts of current. Pin 6 should be shunted to ground with a bleeder resistor to prevent activating the power switch with extraneous leakage currents. CURRENT SENSE CIRCUIT OSCILLATOR SECTION Peak Current (IS) is Determined By The Formula ISMAX 1.0V RS A small RC filter may be required to suppress switch transients. 5

11 UC1842/3/4/5 UC2842/3/4/5 OUTPUT SATURATION CHARACTERISTICS ERROR AMPLIFIER OPEN-LOOP FREQUENCY RESPONSE OPEN-LOOP LABORATORY FIXTURE High peak currents associated with capacitive loads necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5k potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3. SHUT DOWN TECHNIQUES Shutdown of the UC1842 can be accomplished by two methods; either raise pin 3 above 1V or pull pin 1 below a voltage two diode drops above ground. Either method causes the output of the PWM comparator to be high (refer to block diagram). The PWM latch is reset dominant so that the output will remain low until the next clock cycle after the shutdown condition at pin 1 and/or 3 is removed. In one example, an externally latched shutdown may be accomplished by adding an SCR which will be reset by cycling VCC below the lower UVLO threshold. At this point the reference turns off, allowing the SCR to reset. 6

12 UC3842 PROVIDES LOW-COST CURRENT-MODE CONTROL The fundamental challenge of power supply design is to simultaneously realize two conflicting objectives : good electrical performance and low cost. The UC3842 is an integrated pulse width modulator (PWM) designed with both these objectives in mind. This IC provides designers an inexpensive controller with which they can obtain all the performance advantages of current-mode operation. In addition, the UC3842 is optimized for efficient power sequencing of off-line converters and for driving increasingly popular POWERMOS. This application note gives a functional description of the UC3842 and suggests how to incorporate the IC into practical power supplies. A review of currentmode control and its benefits is included and methods of avoiding common pitfalls discussed. The final section presents designs of two power supplies utilizing UC3842 control. CURRENT-MODE CONTROL Figure 1 shows the two-loop current-mode control system in a typical buck regulator application. A clock signal initiates power pulses at a fixed frequency. The termination of each pulse occurs when an analog of the inductor current reaches a threshold established by the error signal. In this way the error signal actually controls peak inductor current. This contrasts with conventional schemes in which the error signal directly controls pulse width without regard to inductor current. Figure 1 : Two-loop Current-mode Control System. AN246/1188 1/16

13 Several performance advantages result from the use of current-mode control. First, an input voltage feed-forward characteristic is achieved ; i.e., the control circuit instantaneously corrects for input voltage variations without using up any of the error amplifier s dynamic range. Therefore, line regulation is excellent and the error amplifier can be dedicated to correcting for load variations exclusively. For converters in which inductor current is continuous, controlling peak current is nearly equivalent to controlling average current. Therefore, when such converters employ current-mode control, the inductor can be treated as an error-voltage-controlled-current-source for the purposes of small-signal analysis. This is illustrated by figure 2. The two-pole control-to-output frequency response of these converters is reduced to a single pole (filter capacitor in parallel with load) response. One result is that the error amplifier compensation can be designed to yield a stable closed-loop converter response with greater gain-bandwidth than would be possible with pulse-width control, giving the supply improved small-signal dynamic response to changing loads. A second result is that the error amplifier compensation circuit becomes simpler and better behaved, as illustrated in figure 3. Capacitor C i and resistor R iz in figure 3a add a low frequency zero which cancels one of the two control-to-output poles of non-current-mode converters. For large-signal load changes, in which converter response is limited by inductor slew rate, the error amplifier will saturate while the inductor is catching up with the load. During this time, C i will charge to an abnormal level. When the inductor current reaches its required level, the voltage on C i causes a corresponding error in supply output vol-tage. The recovery time is Riz Ci, which may be milleseconds. However, the compensation network of figure 3b can be used where current-mode control has eliminated the inductor pole. Large-signal dynamic response is then greatly improved due to the absence of C i. Figure 2 : Inductor Looks Like a Current Source to Small Signals. Figure 3 : Required Error Amplifier Compensation for Continuous Inductor Current Designs using (a) Dutycycle Control and (b) Current-mode Control. (a) (b) 2/16

14 Figure 4 : UC3842 Block Diagram. Current limiting is simplified with current-mode control. Pulse-by-pulse limiting is, of course, inherent in the control scheme. Furthermore, an upper limit on the peak current can be established by simply clamping the error voltage. Accurate current limiting allows optimization of magnetic and power semiconductor elements while ensuring reliable supply operation. Finally, current-mode controlled power stages can be operated in parallel with equal current sharing. This opens the possibility of a modular approach to power supply design. FUNCTIONAL DESCRIPTION A block diagram of the UC3842 appears in figure 4. This IC will operate from a low impedance DC source of 10 V to 30 V. Operation between 10 V and 16 V requires a start-up bootstrap to a voltage greater than 16 V in order to overcome the undervoltage lockout. V CC is internally clamped to 34 V for operation from higher voltage current-limited sources (I CC 30 ma). stage. Figure 5a shows that the UVLO turn-on and turn-off thresholds are fixed internally at 16 V and 10 V respectively. The 6 V hysteresis prevents VCC oscillations during power sequencing. Figure 5b shows supply current requirements. Start-up current is less than 1 ma for efficient bootstrapping from the rectified input of an off-line converter, as illustrated by figure 6. During normal circuit operation, V CC is developed from auxiliary winding W AUX with D 1 and CIN. At start-up, however, CIN must be charged to 16 V through R IN. With a start-up current of 1 ma, R IN can be as large as 100 kω and still charge CIN when V AC = 90 V RMS (low line). Power dissipation in R IN would then be less than 350 mw even under high line (V AC = 130 V RMS) conditions. During UVLO, the UC3842 output driver is biased to a high impedance state. However, leakage currents (up to 10 µa), if not shunted to ground, could pull high the gate of a POWERMOS. A 100 kω shunt, as showing in figure 6, will hold the gate voltage below 1V. UNDER-VOLTAGE LOCKOUT (UVLO) This circuit insures that VCC is adequate to make the UC3842 fully operational before enabling the output 3/16

15 Figure 5 : (a) Under-voltage Lockout and (b) Supply Current Requirements. (a) (b) Figure 6 : Providing Power to the UC3842. OSCILLATOR The UC3842 oscillator is programmed as shown in figure 7a. Oscillator timing capacitor C T is charged from V REF (5 V) through R T, and discharged by an internal current source. Charge and discharge times are given by : t c 0.55 R T C T R T 2.7 td RT CT ln ( ) R T frequency, then, is : f = tc + t d For R T > 5 kω, t d is small compared to t c, and : f 0.55 R T C T R T C T 4/16

16 During the discharge time, the internal clock signal blanks the output to the low state. Therefore, td limits maximum duty cycle (D MAX) to : t c t d D MAX = = 1 t c + t d τ where τ = 1/f = switching period. The timing capacitor discharge current is not tightly controlled, so t d may vary somewhat over temperature and from unit to unit. Therefore, when very precise duty cycle limiting is required, the circuit of figure 7b is recommended. One or more UC3842 oscillators can be synchronized to an external clock as shown in figure 8. Noise immunity is enhanced if the free-running oscillator frequency (f = 1/(tc + td)) is programmed to be ~ 20 % less than the clock frequency. Figure 7 : (a) Oscillator Timing Connections and (b) Circuit for Limiting Duty Cycle. (a) (b) t D c MAX = (th + t L) t H = (R A + R B) C t L = R B C Figure 8 : Synchronization to an External Clock. ERROR AMPLIFIER The error amplifier (E/A) configuration is shown in figure 9. The non-inverting input is not brought out to a pin, but is internally biased to 2.5 V ± 2 %. The E/A output is available at pin 1 for external compensation, allowing the user to control the converter s closed-loop frequency response. Figure 10a shows an E/A compensation circuit suitable for stabilizing any current-mode controlled topology except for flyback and boost converters operating with continuous inductor current. The feedback components add a pole to the loop transfer function at f p = 1/2 πr f C f. R f and C f are chosen so that this pole cancels the zero of the output filter capacitor ESR in the power circuit. R i and R f fix the lowfrequency gain. They are chosen to provide as much gain as possible while still allowing the pole formed by the output filter capacitor and load to roll off the loop gain to unity (0dB) at f f switching/4. This technique insures converter stability while providing good dynamic response. Continuous-inductor-current boost and flyback converters each have a right-half-plane zero in their transfer function. An additional compensation pole is needed to roll off loop gain at a frequency less than that of the RHP zero. R p and C p in the circuit of figure 10b provide this pole. 5/16

17 The E/A output will source 0.5 ma and sink 2 ma. A lower limit for Rf is given by : VE/A OUT(max) 2.5 V 6 V 2.5 V R f (MIN) = = 7 kω 0.5 ma 0.5 ma E/A input bias current (2 µa max) flows through R i, resulting in a DC error in output voltage (V o) given by : It is therefore desirable to keep the value of R i as low as possible. Figure 11 shows the open-loop frequency response of the UC3842 E/A. The gain represent an upper limit on the gain of the compensated E/A. Phase lag increases rapidly as frequency exceeds 1 MHz due to second-order poles at 10 MHz and above. Vo(max) = (2 µa) Ri Figure 9 : UC3842 Error Amplifier. Figure 10 : (a) Error Amplifier Compensation Addition Pole and (b) Needed for Continu ous Inductor-current Boost ad Flyback. Figure 11 : Error Amplifier Open-loop Frequency Response. (a) (b) 6/16

18 CURRENT SENSING AND LIMITING The UC3842 current sense input is configured as shown in figure 12. Current-to-voltage conversion is done externally with ground-referenced resistor RS. Under normal operation the peak voltage across R S is controlled by the E/A according to the following relation : VC 1.4 V V RS (pk) = 3 where : VC = control voltage = E/A output voltage. R S can be connected to the power circuit directly or through a current transformer, as figure 13 illustrates. While a direct connection is simpler, a transformer can reduce power dissipation in R S, reduce errors caused by the base current, and provide level shifting to eliminate the restraint of ground-reference sensing. The relation between V C and peak current in the power stage is given by : V RS(pk) N i (pk) = N ( ) = (V C 1.4) R S 3 R S where : N = current sense transformer turns ratio. = 1 when transformer not used. Figure 12 : Current Sensing. For purposes of small-signal analysis, the controlto-sensed-current gain is : i(pk) N = V C 3 R S When sensing current in series with the power transistor, as shown in figure 13, current waveform will often have a large spike at its leading edge. This is due to rectifier recovery and/or interwinding capacitance in the power transformer. If unattenuated, this transient can prematurely terminate the output pulse. As shown, a simple RC filter is usually adequate to suppress this spike. The RC time constant should be approximately equal to the current spike duration (usually a few hundred nanoseconds). The inverting input to the UC3842 current-sense comparator is internally clamped to 1 V (figure 12). Current limiting occurs if the voltage at pin 3 reaches this threshold value, i.e. the current limit is defined by : N. 1 V imax = R S 7/16

19 Figure 13 : Transformer-coupled Current Sensing. Figure 14 : Output Cross-conduction. TOTEM-POLE OUTPUT The UC3842 has a single totem-pole output. The output transistors can be operated to ± 1 A peak current and ± 200 ma average current. The peak current is self-limiting, so no series current-limiting resistor is needed when driving a power MOS gate. Cross-conduction between the output transistors is minimal, as figure 14 shows. The average added power due to cross-conduction with V i = 30 V is only 80 mw at 200 khz. Figures show suggested circuits for driving POWERMOS and bipolar transistors with the UC3842 output. The simple circuit of figure 15 can be used when the control IC is not electrically isolated from the power MOS. Series resistor R1 provides damping for a parasitic tank circuit formed by the power MOS input capacitance and any series wiring inductance. Resistor R2 shunts output leakage currents (10 µa maximum) to ground when the under-voltage lockout is active. Figure 16 shows an isolated power MOS drive circuit which is appropriate when the drive signal must be levelshifted or transmitted across an isolation boundary. Bipolar transistors can be driven effectively with the circuit of figure 17. Resistors R 1 and R 2 fix the on-state base current. Capacitor C 1 provides a negative base current pulse to remove stored charge at turn-off. SHUTDOWN TECHNIQUES Shutdown of the UC3842 can be accomplished by two methods ; either raise pin 3 above 1 V or pull pin 1 below 1 V. Either method causes the output of the PWM comparator to be high (refer to block diagram, figure 4). The PWM latch is reset dominant so that the output will remain low until the first clock pulse following removal of the shutdown signal at pin 1 or pin 3. As shown in figure 18, an externally latched shutdown can be accomplished by adding an SCR which will be reset by cycling V CC below the lower under-voltage lockout threshold (10 V). At this point all internal bias is removed, allowing the SCR to reset. Figure 15 : Direct POWERMOS Drive. PWM LATCH This flip-flop, shown in figure 4, ensures that only a single pulse appears at the UC3842 output in any one oscillator period. Excessive power transistor dissipation and potential saturation of magnetic elements are thereby averted. 8/16

20 Figure 16 : Isolated POWERMOS Drive. Figure 17 : Bipolar Drive with Negative Turn-off Bias. AVOIDING COMMON PITFALLS Current-mode controlled converters can exhibit performance peculiarities under certain operating conditions. This section explains these situations and how to correct them when using the UC3842. SLOPE COMPENSATION PREVENTS INSTABILI- TIES It is well documented that current-mode controlled converters can exhibit subharmonic oscillations when operated at duty cycles greater than 50 %. Fortunately, a simple technique (usually requiring only a single resistor to implement) exists which corrects this problem and at the same time improves converter performance in other respects. This "slope compensation" technique is described in detail in Reference 6. It should be noted that "duty cycle" here refers to output pulse width divided by oscillator period, even in push-pull designs where the transformer period is twice that of the oscillator. Therefore, push-pull circuits will almost always require slope compensation to prevent subharmonic oscillation. 9/16

21 Figure 18 : Shutdown Achieved by (a) Pulling Pin 3 High (b) Pulling Pin 1 Low. (a) (b) Figure 19 illustrates the slope compensation technique. In figure 19a the uncompensated control voltage and current sense waveforms are shown as a reference. Current is often sensed in series with the switching transistor for buck-derived topologies. In this case, the current sense signal does not track the decaying inductor current when the transistor is off, so dashed lines indicate this inductor current. The negative inductor current slope is fixed by the values of output voltage (V o) and inductance (L) : di L V L V F V o (V F + V o) = = = dt L L L where : V F = forward voltage drop across the freewheeling diode. The actual slope (m 2) of the dashed lines in figure 19a is given by : R S di L R S (V F + V o) m 2 =. = N dt NL where : R S and N are defined as the "Current Sensing" section of this paper. In figure 19b, a sawtooth voltage with slope m has been added to the control signal. The sawtooth is synchronized with the PWM clock, and practice is most easily derived from the control chip oscillator as shown in figure 20a. The sawtooth slope in figure 19b is m = m 2/2. This particular slope value is significant in that it yields "perfect" current-mode control ; i.e. with m 2/2 the average inductor current follows the control signal so that, in the small-signal analysis, the inductor acts as a controlled current source. All current-mode controlled converters having continuous inductor current therefore benefit from this amount of slope compensation, whether or not they operate above 50 % duty. More slope is needed to prevent subharmonic oscillations at high duty cycles. With slope m = m2, such oscillations will not occur if the error amplifier gain (A V(E/A)) at half the switching frequency (f s/2) is kept below a threshold value (reference 6) : π 2 CO A V (E/A) < 4 τ m = m2 f = fs/2 where : C o = sum of filter and load capacitance τ = 1/fs Slope compensation can also improve the noise immunity of a current-mode controlled supply. When the inductor ripple current is small compared to the average current (as in figure 19a), a small amount of noise on the current sense or control signals can cause a large pulse-width jitter. The magnitude of this jitter varies inversely with the difference in slope of the two signals. By adding slope as in figure 19b, the jitter is reduced. In noisy environments it is sometimes necessary to add slope m > m 2 in order to correct this problem. However, as m increases beyond m = m2/2, the circuit becomes less perfectly current controlled. A complex trade-off is then required ; for very noisy circuits the optimum amount of slope compensation is best found empirically. Once the required slope is determined, the value of RSLOPE in figure 20a can be calculated : VRAMP 0.7 V RSLOPE 1.4 RSLOPE 3 m =. AV(E/A) = ( ) = ( ) tramp τ/2 ZF fs τ ZF fs 3 m τ R SLOPE = (Z F f s) = 2.1. m. τ. Z F f s 1.4 where : Z F f s is the E/A feedback impedance at the switching frequency. For m = m L : τ RAMP R s (V F + V O) RSLOPE = 1.7 τ ( ) ZF fs NL 10/16

22 Figure 19 : Slope Compensation Waveforms : (a) No Comp. (b) Comp. Added to Control Voltage. (c) Comp. Added to Current Sense. Note that in order for the error amplifier to accurately replicate the ramp, Z F must be constant over the frequency range f s to at least 3 f s. In order to eliminate this last constraint, an alternative method of slope compensation is shown in figures 19c and 20b. Here the artificial slope is added to the current sense waveform rather than subtracted from the control signal. The magnitude of the added slope still relates to the downslope of inductor current as described above. The requirement for R SLOPE is now : V RAMP R f 0.7 R f m = ( ) = ( ) t RAMP R f + R SLOPE τ/2 R f + R SLOPE 1.4 R f 1.4 R SLOPE = R f = R f ( 1) mτ mτ For m = m 2 : 1.4 NL R SLOPE = R f ( 1) RS (VF + VO) τ R SLOPE loads the UC3842 R T/C T terminal so as to cause a decrease in oscillator frequency. If R SLO- PE >> RT then the frequency can be corrected by decreasing R T slightly. However, with R SLOPE 5 R T the linearity of the ramp degrades noticeably, causing over-compensation of the supply at low duty cycles. This can be avoided by driving R SLOPE with an emitter-follower as shown in figure /16

23 Figure 20 : Slope Compensation Added (a) to Control Signal or (b) to Current Sense Waveform. (a) (b) Figure 21 : Emitter-follower Minimizes Load at RT/CT Terminal. NOISE As mentioned earlier, noise on the current sense or control signals can cause significant pulse-width jitter, particularly with continuous-inductor-current designs. While slope compensation helps alleviate this problem, a better solution is to minimize the amount of noise. In general, noise immunity improves as impedance decrease at critical points in a circuit. One such point for a switching supply is the ground line. Small wiring inductances between various ground points on a PC board can support commonmode noise with sufficient amplitude to interfere with correct operation of the modulating IC. A copper ground plane and separate return lines for high-current paths greatly reduce common-mode noise. 12/16

24 Note that the UC3842 has a single ground pin. High sink currents in the output therefore cannot be returned separately. Ceramic bypass capacitors (0.1 µf) from V I and V REF to ground will provide low-impedance paths for high frequency transients at those points. The input to the error amplifier, however, is a high-impedance point which cannot be bypassed without affecting the dynamic response of the power supply. Therefore, care should be taken to lay out the board in such a way that the feedback path is far removed from noise generating components such as the power transistor(s). Figure 22a illustrates another common noise-induced problem. When the power transistor turns off, a noise spike is coupled to the oscillator RT/CT terminal. At high duty cycles the voltage at R T/C T is approaching its threshold level ( 2.7 V, established by Figure 22 : (a) Noise on Pin 4 Can Cause Oscillator to Pre-trigger. (b) With External Sync. Noise Does not Approach threshold Level. the internal oscillator circuit) when this spike occurs. A spike of sufficient amplitude will prematurely trip the oscillator as shown by the dashed lines. In order to minimize the noise spike, choose CT as large as possible, remembering that deadtime increases with C T. It is recommended that C T never be less than 1000 pf. Often the noise which causes this problem is caused by the output (pin 6) being pulled below ground at turn-off by external parasitics. This is particularly true when driving POWERMOS. A diode clamp from ground to pin 6 will prevent such output noise from feeding to the oscillator. If these measures fail to correct the problem, the oscillator frequency can always be stabilized with an external clock. Using the circuit of figure 8 results in an R T/C T waveform like that of figure 22b. Here the oscillator is much more immune to noise because the ramp voltage never closely approaches the internal threshold. (a) (b) MAXIMUM OPERATING FREQUENCY Since output deadtime varies directly with C T, the restraint on minimum C T (1000 pf) mentioned above results in a minimum deadtime varies for the UC3842. This minimum deadtime varies with R T and therefore with frequency, as shown in figure 23. Above 100 khz, the deadtime significantly reduces the maximum duty cycle obtainable at the UC3842 output (also show in figure 23). Circuits not requiring large duty cycles, such as the forward converter and flyback topologies, could operate as high as 500 khz. Operation at higher frequencies is not recommended because the deadtime become less predictable. The speed of the UC3842 current sense section poses an additional constraint on maximum operating frequency. A maximum current sense delay of 400 ns represents 10 % of the switching period at 250 khz and 20 % at 500 khz. Magnetic components must not saturate as the current continues to rise during this delay period, and power semiconductors must be chosen to handle the resulting peak currents. In short, above 250 khz, may of the advantages of higher-frequency operation are lost. 13/16

25 Figure 23 : Deadtime and Maximum Obtainable Duty-cycle vs. Frequency with Minimum Recommended C T. CIRCUIT EXAMPLES 1. OFF-LINE FLYBACK Figure 24 shows a 25 W multiple-output off-line flyback regulator controlled with the UC3842. This regulator is low in cost because it uses only two magnetic elements, a primary-side voltage sensing technique, and an inexpensive control circuit. Specifications are listed below. SPECIFICATIONS : Line Isolation : Switching Frequency : 3750 V 40 khz full load : 70 % Input Voltage Output Voltage : 95 VAC to 130 VAC (50Hz/60Hz) A. + 5 V, 5 % : 1 A to 4 A load Ripple voltage : 50 mv P-P Max. B V, 3 % : 0.1 A to 0.3 A load Ripple voltage : 100 mv P-P Max C. 12 V, 3 % 0.1 A to 0.3 A load Ripple voltage : 100 mv P-P Max 14/16

UC3842/UC3843/UC3844/UC3845

UC3842/UC3843/UC3844/UC3845 SMPS Controller www.fairchildsemi.com Features Low Start up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency up to 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequencycurrent-mode

More information

UC3842 PROVIDES LOW-COST CURRENT-MODE CONTROL

UC3842 PROVIDES LOW-COST CURRENT-MODE CONTROL UC3842 PROVIDES LOW-COST CURRENT-MODE CONTROL The fundamental challenge of power supply design is to simultaneously realize two conflicting objectives : good electrical performance and low cost. The UC3842

More information

UC3842/UC3843/UC3844/UC3845

UC3842/UC3843/UC3844/UC3845 SMPS Controller www.fairchildsemi.com Features Low Start Up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency Up To 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequency

More information

Current Mode PWM Controller

Current Mode PWM Controller Current Mode PWM Controller UC1842/3/4/5 FEATURES Optimized For Off-line And DC To DC Converters Low Start Up Current (

More information

Current Mode PWM Controller

Current Mode PWM Controller application INFO available UC1842/3/4/5 Current Mode PWM Controller FEATURES Optimized For Off-line And DC To DC Converters Low Start Up Current (

More information

Vref. Good Logic 1/3Vref CURRENT SENSE COMPARATOR OSCILLATOR

Vref. Good Logic 1/3Vref CURRENT SENSE COMPARATOR OSCILLATOR UTC UCA / A CURRENT MODE PWM CONTROL CIRCUITS DESCRIPTION The UTC UCA/A provide the necessary functions to implement off-line or DC to DC fixed frequency current mode, controlled switching circuits with

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

Current Mode PWM Controller

Current Mode PWM Controller Current Mode PWM Controller application INFO available FEATURES Optimized for Off-line and DC to DC Converters Low Start Up Current (

More information

CURRENT MODE PWM CONTROLLER LM3842A/3A/4A/5A

CURRENT MODE PWM CONTROLLER LM3842A/3A/4A/5A CURRENT MODE PWM CONTROLLER LMA/A/A/5A FEATURES SOP/ DIP PIN Configulation Automatic feed forward compensation Optimized for offline converter Double pulse suppression Current mode operation to 500 KHz

More information

Current-mode PWM controller

Current-mode PWM controller DESCRIPTION The is available in an 8-Pin mini-dip the necessary features to implement off-line, fixed-frequency current-mode control schemes with a minimal external parts count. This technique results

More information

Current Mode PWM Controller

Current Mode PWM Controller Current Mode PWM Controller FEATURES Optimized for Off-line and DC to DC Converters Low Start Up Current (

More information

UNISONIC TECHNOLOGIES CO., LTD

UNISONIC TECHNOLOGIES CO., LTD UNISONIC TECHNOLOGIES CO., LTD CURRENT MODE PWM CONTROL CIRCUITS DESCRIPTION The UTC UC3842A/3843A provide the necessary functions to implement off-line or DC to DC fixed frequency current mode, controlled

More information

High Speed PWM Controller

High Speed PWM Controller High Speed PWM Controller FEATURES Compatible with Voltage or Current Mode Topologies Practical Operation Switching Frequencies to 1MHz 50ns Propagation Delay to Output High Current Dual Totem Pole Outputs

More information

UC3843 DESCRIPTION FEATURES PACKAGE INFORMATION

UC3843 DESCRIPTION FEATURES PACKAGE INFORMATION DESCRIPTION TheUC3842A-BW/43A-BW/44A-BW/45A-BW,UC384 2M/43M/44M/45M are fixed frequency current mode PWM controller. They are specially designed for OFF Line and DC to DC converter applications with a

More information

High Speed PWM Controller

High Speed PWM Controller High Speed PWM Controller application INFO available FEATURES Compatible with Voltage or Current Mode Topologies Practical Operation Switching Frequencies to 1MHz 50ns Propagation Delay to Output High

More information

UNISONIC TECHNOLOGIES CO., LTD UC3842B/3843B

UNISONIC TECHNOLOGIES CO., LTD UC3842B/3843B UNISONIC TECHNOLOGIES CO., LTD UC3842B/3843B HIGH PERFORMANCE CURRENT MODE CONTROLLERS DESCRIPTION The UTC UC3842B/3843B are specifically designed for off-line and dc-to-dc converter applications offering

More information

High Speed PWM Controller

High Speed PWM Controller High Speed PWM Controller FEATURES Compatible with Voltage or Current Mode Topologies Practical Operation Switching Frequencies to 1MHz 50ns Propagation Delay to Output High Current Dual Totem Pole Outputs

More information

UC284x, UC384x, UC384xY CURRENT-MODE PWM CONTROLLERS

UC284x, UC384x, UC384xY CURRENT-MODE PWM CONTROLLERS Optimized for Off-Line and dc-to-dc Converters Low Start-Up Current (

More information

CURRENT-MODE PWM CONTROLLERS FEATURES ORDERING INFORMATION BLOCK DIAGRAM

CURRENT-MODE PWM CONTROLLERS FEATURES ORDERING INFORMATION BLOCK DIAGRAM CURRENT-MODE PWM CONTROLLERS The KA3842B/3B/4B/5B are fixed frequency current-mode PWM controller. They are specially designed for Off - Line and DC-to-DC converter applications with minimal external components.

More information

ML4818 Phase Modulation/Soft Switching Controller

ML4818 Phase Modulation/Soft Switching Controller Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation

More information

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1 % 100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME CONTROL INTERNAL

More information

FA5310BP(S), FA5314P(S), FA5316P(S) FA5311BP(S), FA5315P(S), FA5317P(S)

FA5310BP(S), FA5314P(S), FA5316P(S) FA5311BP(S), FA5315P(S), FA5317P(S) 0.05 FA531X series series Bipolar IC For Switching Power Supply Control FA5310BP(S), FA5314P(S), FA5316P(S) FA5311BP(S), FA5315P(S), FA5317P(S) Description The FA531X series are bipolar ICs for switching

More information

MIC38C42A/43A/44A/45A

MIC38C42A/43A/44A/45A MIC38C42A/43A/44A/45A BiCMOS Current-Mode PWM Controllers General Description The MIC38C4xA are fixed frequency, high performance, current-mode PWM controllers. Micrel s BiCMOS devices are pin compatible

More information

Current Mode PWM Controller

Current Mode PWM Controller Current Mode PWM Controller FEATURES Automatic Feed Forward Compensation Programmable Pulse-by-Pulse Current Limiting Automatic Symmetry Correction in Push-pull Configuration Enhanced Load Response Characteristics

More information

Features. 5V Reference UVLO. Oscillator S R GND*(AGND) 5 (9) ISNS 3 (5)

Features. 5V Reference UVLO. Oscillator S R GND*(AGND) 5 (9) ISNS 3 (5) MIC38HC42/3/4/5 BiCMOS 1A Current-Mode PWM Controllers General Description The MIC38HC4x family are fixed frequency current-mode PWM controllers with 1A drive current capability. Micrel s BiCMOS devices

More information

Current Mode PWM Controller

Current Mode PWM Controller Current Mode PWM Controller FEATURES Automatic Feed Forward Compensation Programmable Pulse-by-Pulse Current Limiting Automatic Symmetry Correction in Push-pull Configuration Enhanced Load Response Characteristics

More information

Features. 5V Reference UVLO. Oscillator S R

Features. 5V Reference UVLO. Oscillator S R MIC38C42/3/4/5 BiCMOS Current-Mode PWM Controllers General Description The MIC38C4x are fixed frequency, high performance, current-mode PWM controllers. Micrel s BiCMOS devices are pin compatible with

More information

Advanced Regulating Pulse Width Modulators

Advanced Regulating Pulse Width Modulators Advanced Regulating Pulse Width Modulators FEATURES Complete PWM Power Control Circuitry Uncommitted Outputs for Single-ended or Push-pull Applications Low Standby Current 8mA Typical Interchangeable with

More information

Programmable, Off-Line, PWM Controller

Programmable, Off-Line, PWM Controller Programmable, Off-Line, PWM Controller FEATURES All Control, Driving, Monitoring, and Protection Functions Included Low-Current Off Line Start Circuit Voltage Feed Forward or Current Mode Control High

More information

C URRENT M ODE PWM C ONTROLLER R ST I ST SG3842 PACKAGE ORDER INFO. T A ( C) M RoHS / Pb-free Transition DC: 0503 RoHS / Pb-free Transition DC:0440

C URRENT M ODE PWM C ONTROLLER R ST I ST SG3842 PACKAGE ORDER INFO. T A ( C) M RoHS / Pb-free Transition DC: 0503 RoHS / Pb-free Transition DC:0440 TM SG1842/SG1843 Series C URRENT M ODE PWM C ONTROLLER P R O D U I O N D A T A S H E E T DESCRIPTION The family of control IC's provides all the necessary features to implement off-line fixed frequency,

More information

Regulating Pulse Width Modulators

Regulating Pulse Width Modulators Regulating Pulse Width Modulators UC1525A/27A FEATURES 8 to 35V Operation 5.1V Reference Trimmed to ±1% 100Hz to 500kHz Oscillator Range Separate Oscillator Sync Terminal Adjustable Deadtime Control Internal

More information

Advanced Regulating Pulse Width Modulators

Advanced Regulating Pulse Width Modulators Advanced Regulating Pulse Width Modulators FEATURES Complete PWM Power Control Circuitry Uncommitted Outputs for Single-ended or Push-pull Applications Low Standby Current 8mA Typical Interchangeable with

More information

UC3525A. SMPS Controller. Features. Description. Internal Block Diagram.

UC3525A. SMPS Controller. Features. Description. Internal Block Diagram. SMPS Controller www.fairchildsemi.com Features 5V ± 1% Reference Oscillator Sync terminal Internal Soft Start Deadtime Control Under-Voltage Lockout Description UC3525A is a monolithic integrated circuit

More information

EUP3410/ A,16V,380KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

EUP3410/ A,16V,380KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit 2A,16V,380KHz Step-Down Converter DESCRIPTION The is a current mode, step-down switching regulator capable of driving 2A continuous load with excellent line and load regulation. The can operate with an

More information

Advanced Regulating Pulse Width Modulators

Advanced Regulating Pulse Width Modulators Advanced Regulating Pulse Width Modulators FEATURES Complete PWM Power Control Circuitry Uncommitted Outputs for Single-ended or Push-pull Applications Low Standby Current 8mA Typical Interchangeable with

More information

TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

PJ494 Switchmode Pulse Width Modulation Control Circuit

PJ494 Switchmode Pulse Width Modulation Control Circuit T he PJ494 incorporates on a single monolithic chip all the functions required in the construction of a pulsewidth-modulation control circuit. Designed primarily for power supply control, these devices

More information

Features MIC2193BM. Si9803 ( 2) 6.3V ( 2) VDD OUTP COMP OUTN. Si9804 ( 2) Adjustable Output Synchronous Buck Converter

Features MIC2193BM. Si9803 ( 2) 6.3V ( 2) VDD OUTP COMP OUTN. Si9804 ( 2) Adjustable Output Synchronous Buck Converter MIC2193 4kHz SO-8 Synchronous Buck Control IC General Description s MIC2193 is a high efficiency, PWM synchronous buck control IC housed in the SO-8 package. Its 2.9V to 14V input voltage range allows

More information

UTC UNISONIC TECHNOLOGIES CO., LTD. 1 HIGH PERFORMANCE CURRENT MODE CONTROLLERS

UTC UNISONIC TECHNOLOGIES CO., LTD. 1 HIGH PERFORMANCE CURRENT MODE CONTROLLERS HIGH PERFORMANCE CURRENT MODE CONTROLLERS DESCRIPTION The UTC UC3842B/3843B are specifically designed for Off-Line and dc-to-dc converter applications offering the designer a cost-effective solution with

More information

Preliminary. Synchronous Buck PWM DC-DC Controller FP6329/A. Features. Description. Applications. Ordering Information.

Preliminary. Synchronous Buck PWM DC-DC Controller FP6329/A. Features. Description. Applications. Ordering Information. Synchronous Buck PWM DC-DC Controller Description The is designed to drive two N-channel MOSFETs in a synchronous rectified buck topology. It provides the output adjustment, internal soft-start, frequency

More information

High Speed PWM Controller

High Speed PWM Controller High Speed PWM Controller application INFO available FEATURES Compatible with Voltage or Current Mode Topologies Practical Operation Switching Frequencies to 1MHz 50ns Propagation Delay to Output High

More information

KA7500B. SMPS Controller. Features. Description. Internal Block Diagram.

KA7500B. SMPS Controller. Features. Description. Internal Block Diagram. SMPS Controller www.fairchildsemi.com Features Internal Regulator Provides a Stable 5V Reference Supply Trimmed to 5% Uncommitted Output TR for 200mA Sink or Source Current Output Control For Push-Pull

More information

TL594C, TL594I, TL594Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL594C, TL594I, TL594Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

EUP V/12V Synchronous Buck PWM Controller DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit. 1

EUP V/12V Synchronous Buck PWM Controller DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit. 1 5V/12V Synchronous Buck PWM Controller DESCRIPTION The is a high efficiency, fixed 300kHz frequency, voltage mode, synchronous PWM controller. The device drives two low cost N-channel MOSFETs and is designed

More information

UNISONIC TECHNOLOGIES CO., LTD

UNISONIC TECHNOLOGIES CO., LTD U UNISONIC TECHNOLOGIES CO., LTD REGULATING PWM IC DESCRIPTION The UTC U is a pulse width modulator IC and designed for switching power supplies application to improve performance and reduce external parts

More information

Switched Mode Controller for DC Motor Drive

Switched Mode Controller for DC Motor Drive Switched Mode Controller for DC Motor Drive FEATURES Single or Dual Supply Operation ±2.5V to ±20V Input Supply Range ±5% Initial Oscillator Accuracy; ± 10% Over Temperature Pulse-by-Pulse Current Limiting

More information

TL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

EUP3452A. 2A,30V,300KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

EUP3452A. 2A,30V,300KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit 2A,30V,300KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 2A continuous load with excellent line and load regulation. The can operate with an input

More information

Techcode TD8215. Step-up DC/DC Controller. General Description. Features. Applications. Pin Configurations DATASHEET TD8215 INV SCP VDD CTL

Techcode TD8215. Step-up DC/DC Controller. General Description. Features. Applications. Pin Configurations DATASHEET TD8215 INV SCP VDD CTL General Description Features The is a single PWM, step up DC DC controller with low operating voltage application integrating softstart and short circuit detection function. The oscillator switching frequency

More information

EUP A,40V,200KHz Step-Down Converter

EUP A,40V,200KHz Step-Down Converter 3A,40V,200KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 3A continuous load with excellent line and load regulation. The operates with an input

More information

TL494M PULSE-WIDTH-MODULATION CONTROL CIRCUIT

TL494M PULSE-WIDTH-MODULATION CONTROL CIRCUIT Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

FEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE

FEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE DESCRIPTION The is a monolithic synchronous buck regulator. The device integrates 100mΩ MOSFETS that provide 2A continuous load current over a wide operating input voltage of 4.75V to 25V. Current mode

More information

Isolated High Side FET Driver

Isolated High Side FET Driver UC1725 Isolated High Side FET Driver FEATURES Receives Both Power and Signal Across the Isolation Boundary 9 to 15 Volt High Level Gate Drive Under-voltage Lockout Programmable Over-current Shutdown and

More information

Features. RAMP Feed Forward Ramp/ Volt Sec Clamp Reference & Isolation. Voltage-Mode Half-Bridge Converter CIrcuit

Features. RAMP Feed Forward Ramp/ Volt Sec Clamp Reference & Isolation. Voltage-Mode Half-Bridge Converter CIrcuit MIC3838/3839 Flexible Push-Pull PWM Controller General Description The MIC3838 and MIC3839 are a family of complementary output push-pull PWM control ICs that feature high speed and low power consumption.

More information

2A, 23V, 380KHz Step-Down Converter

2A, 23V, 380KHz Step-Down Converter 2A, 23V, 380KHz Step-Down Converter General Description The is a buck regulator with a built-in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent

More information

KA7500C. SMPS Controller. Features. Description. Internal Block Diagram.

KA7500C. SMPS Controller. Features. Description. Internal Block Diagram. SMPS Controller www.fairchildsemi.com Features Internal regulator provides a stable 5V reference supply trimmed to ±1 % Accuracy. Uncommitted output TR for 200mA sink or source current Output control for

More information

SG2524 SG3524 REGULATING PULSE WIDTH MODULATORS

SG2524 SG3524 REGULATING PULSE WIDTH MODULATORS SG2524 SG3524 REGULATING PULSE WIDTH MODULATORS COMPLETE PWM POWER CONTROL CIR- CUITRY UNCOMMITTED OUTPUTS FOR SINGLE- ENDED OR PUSH PULL APPLICATIONS LOW STANDBY CURRENT 8mA TYPICAL OPERATION UP TO 300KHz

More information

.100 Hz TO 500 KHz OSCILLATOR RANGE

.100 Hz TO 500 KHz OSCILLATOR RANGE SG2525A/2527A SG3525A/3527A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1%.100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME

More information

Features. Slope Comp Reference & Isolation

Features. Slope Comp Reference & Isolation MIC388/389 Push-Pull PWM Controller General Description The MIC388 and MIC389 are a family of complementary output push-pull PWM control ICs that feature high speed and low power consumption. The MIC388/9

More information

SG1524/SG2524/SG3524 REGULATING PULSE WIDTH MODULATOR DESCRIPTION FEATURES HIGH RELIABILITY FEATURES - SG1524 BLOCK DIAGRAM

SG1524/SG2524/SG3524 REGULATING PULSE WIDTH MODULATOR DESCRIPTION FEATURES HIGH RELIABILITY FEATURES - SG1524 BLOCK DIAGRAM SG54/SG54/SG54 REGULATING PULSE WIDTH MODULATOR DESCRIPTION This monolithic integrated circuit contains all the control circuitry for a regulating power supply inverter or switching regulator. Included

More information

FAN7527. Power Factor Correction Controller. Features. Description. Applications.

FAN7527. Power Factor Correction Controller. Features. Description. Applications. Power Factor Correction Controller www.fairchildsemi.com Features Internal Startup Timer Internal R/C filter eliminates the Need for an External R/C filter Very Precise Adjustable Output Over Voltage Protection

More information

Features MIC2194BM VIN EN/ UVLO CS OUTP VDD FB. 2k COMP GND. Adjustable Output Buck Converter MIC2194BM UVLO

Features MIC2194BM VIN EN/ UVLO CS OUTP VDD FB. 2k COMP GND. Adjustable Output Buck Converter MIC2194BM UVLO MIC2194 400kHz SO-8 Buck Control IC General Description s MIC2194 is a high efficiency PWM buck control IC housed in the SO-8 package. Its 2.9V to 14V input voltage range allows it to efficiently step

More information

Universal Input Switchmode Controller

Universal Input Switchmode Controller Universal Input Switchmode Controller Si9120 FEATURES 10- to 0- Input Range Current-Mode Control 12-mA Output Drive Internal Start-Up Circuit Internal Oscillator (1 MHz) and DESCRIPTION The Si9120 is a

More information

PD3842A/3A/4A/5A High Performance Current-Mode Controllers

PD3842A/3A/4A/5A High Performance Current-Mode Controllers High Performance Current-Mode Controllers Description The are high performance fixed frequency current-mode PWM controller series. These integrated circuits are optimized for off-line and DC-DC converter

More information

FAN7527B. Power Factor Correction Controller. Features. Description. Applications.

FAN7527B. Power Factor Correction Controller. Features. Description. Applications. Power Factor Correction Controller www.fairchildsemi.com Features Internal start-up timer Internal R/C filter eliminates the need for an external R/C filter Very precise adjustable output over voltage

More information

Resonant-Mode Power Supply Controllers

Resonant-Mode Power Supply Controllers Resonant-Mode Power Supply Controllers UC1861-1868 FEATURES Controls Zero Current Switched (ZCS) or Zero Voltage Switched (ZVS) Quasi-Resonant Converters Zero-Crossing Terminated One-Shot Timer Precision

More information

TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUIT

TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUIT Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

VCC. UVLO internal bias & Vref. Vref OK. PWM Comparator. + + Ramp from Oscillator GND

VCC. UVLO internal bias & Vref. Vref OK. PWM Comparator. + + Ramp from Oscillator GND Block Diagram VCC 40V 16.0V/ 11.4V UVLO internal bias & Vref RT OSC EN Vref OK EN OUT Green-Mode Oscillator S COMP 2R R Q R PWM Comparator CS Leading Edge Blanking + + Ramp from Oscillator GND Absolute

More information

LD7577 1/15/2009. High Voltage Green-Mode PWM Controller with Brown-Out Protection. General Description. Features. Applications. Typical Application

LD7577 1/15/2009. High Voltage Green-Mode PWM Controller with Brown-Out Protection. General Description. Features. Applications. Typical Application Rev. 01 General Description High Voltage Green-Mode PWM Controller with Brown-Out Protection The LD7577 integrates several functions of protections, and EMI-improved solution in SOP-8 package. It minimizes

More information

EUP A,30V,1.2MHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

EUP A,30V,1.2MHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit 1.2A,30V,1.2MHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 1.2A continuous load with excellent line and load regulation. The can operate with

More information

TL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

DUAL STEPPER MOTOR DRIVER

DUAL STEPPER MOTOR DRIVER DUAL STEPPER MOTOR DRIVER GENERAL DESCRIPTION The is a switch-mode (chopper), constant-current driver with two channels: one for each winding of a two-phase stepper motor. is equipped with a Disable input

More information

MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter

MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter The Future of Analog IC Technology MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter DESCRIPTION The MP2313 is a high frequency synchronous rectified step-down switch mode converter

More information

CR6842. Green-Power PWM Controller with Freq. Jittering. Features. Applications. General Description. Leading-edge blanking on Sense input

CR6842. Green-Power PWM Controller with Freq. Jittering. Features. Applications. General Description. Leading-edge blanking on Sense input Green-Power PWM Controller with Freq. Jittering Features Low Cost, Green-Power Burst-Mode PWM Very Low Start-up Current ( about 7.5µA) Low Operating Current ( about 3.0mA) Current Mode Operation Under

More information

TL598 PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL598 PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power Control Function Totem-Pole Outputs for 200-mA Sink or Source Current Output Control Selects Parallel or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either Output

More information

LD7536E 5/28/2012. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features.

LD7536E 5/28/2012. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features. 5/28/2012 Green-Mode PWM Controller with Frequency Swapping and Integrated Protections Rev. 00 General Description The is built-in with several functions, protection and EMI-improved solution in a tiny

More information

2A, 23V, 380KHz Step-Down Converter

2A, 23V, 380KHz Step-Down Converter 2A, 23V, 380KHz Step-Down Converter FP6182 General Description The FP6182 is a buck regulator with a built in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range

More information

TL494C, TL494I, TL494M, TL494Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS

TL494C, TL494I, TL494M, TL494Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either

More information

LD7523 6/16/2009. Smart Green-Mode PWM Controller with Multiple Protections. General Description. Features. Applications. Typical Application REV: 00

LD7523 6/16/2009. Smart Green-Mode PWM Controller with Multiple Protections. General Description. Features. Applications. Typical Application REV: 00 6/16/2009 Smart Green-Mode PWM Controller with Multiple Protections REV: 00 General Description The LD7523 is a low startup current, current mode PWM controller with green-mode power-saving operation.

More information

AS384x. Current Mode Controller. ASTEC Semiconductor. Description. Features. Pin Configuration Ñ Top view. Ordering Information

AS384x. Current Mode Controller. ASTEC Semiconductor. Description. Features. Pin Configuration Ñ Top view. Ordering Information SEMICONDUCTOR Features 2. V bandgap reference trimmed to.0% and temperature-compensated Standard temperature range extended to 0 C AS3842/3 oscillations trimmed for precision duty cycle clamp AS3844/ have

More information

1MHz, 3A Synchronous Step-Down Switching Voltage Regulator

1MHz, 3A Synchronous Step-Down Switching Voltage Regulator FEATURES Guaranteed 3A Output Current Efficiency up to 94% Efficiency up to 80% at Light Load (10mA) Operate from 2.8V to 5.5V Supply Adjustable Output from 0.8V to VIN*0.9 Internal Soft-Start Short-Circuit

More information

U LTRA-LOW S TART-UP C URRENT, C URRENT-MODE PWM P RODUCTION D ATA S HEET

U LTRA-LOW S TART-UP C URRENT, C URRENT-MODE PWM P RODUCTION D ATA S HEET U LTRA-LOW S TART-UP C URRENT, C URRENT-MODE PWM T HE I NFINITE P OWER OF I NNOVATION P RODUCTION D ATA S HEET DESCRIPTION The LX155x family of ultra-low start-up current (250µA max), current mode control

More information

Phase Shift Resonant Controller

Phase Shift Resonant Controller Phase Shift Resonant Controller FEATURES Programmable Output Turn On Delay; Zero Delay Available Compatible with Voltage Mode or Current Mode Topologies Practical Operation at Switching Frequencies to

More information

EUP A,30V,500KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

EUP A,30V,500KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit 5A,30V,500KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 5A continuous load with excellent line and load regulation. The operates with an input

More information

LD /15/2011. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. Features. General Description.

LD /15/2011. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. Features. General Description. 12/15/2011 Green-Mode PWM Controller with Frequency Swapping and Integrated Protections Rev. 02a General Description The LD7536 is built-in with several functions, protection and EMI-improved solution

More information

Phase Shift Resonant Controller

Phase Shift Resonant Controller Phase Shift Resonant Controller application INFO available UC1875/6/7/8 FEATURES Zero to 100% Duty Cycle Control Programmable Output Turn-On Delay Compatible with Voltage or Current Mode Topologies Practical

More information

4.5V to 32V Input High Current LED Driver IC For Buck or Buck-Boost Topology CN5816. Features: SHDN COMP OVP CSP CSN

4.5V to 32V Input High Current LED Driver IC For Buck or Buck-Boost Topology CN5816. Features: SHDN COMP OVP CSP CSN 4.5V to 32V Input High Current LED Driver IC For Buck or Buck-Boost Topology CN5816 General Description: The CN5816 is a current mode fixed-frequency PWM controller for high current LED applications. The

More information

EVALUATION KIT AVAILABLE 28V, PWM, Step-Up DC-DC Converter PART V IN 3V TO 28V

EVALUATION KIT AVAILABLE 28V, PWM, Step-Up DC-DC Converter PART V IN 3V TO 28V 19-1462; Rev ; 6/99 EVALUATION KIT AVAILABLE 28V, PWM, Step-Up DC-DC Converter General Description The CMOS, PWM, step-up DC-DC converter generates output voltages up to 28V and accepts inputs from +3V

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

MIC2296. General Description. Features. Applications. High Power Density 1.2A Boost Regulator

MIC2296. General Description. Features. Applications. High Power Density 1.2A Boost Regulator High Power Density 1.2A Boost Regulator General Description The is a 600kHz, PWM dc/dc boost switching regulator available in a 2mm x 2mm MLF package option. High power density is achieved with the s internal

More information

UNISONIC TECHNOLOGIES CO., LTD TL594

UNISONIC TECHNOLOGIES CO., LTD TL594 UNISONIC TECHNOLOGIES CO., LTD TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUIT DESCRIPTION The UTC TL594 is a PWM (Pulse Width Modulation) control circuit, incorporating two error amplifiers, an on-chip adjustable

More information

FL6961 Single-Stage Flyback and Boundary Mode PFC Controller for Lighting

FL6961 Single-Stage Flyback and Boundary Mode PFC Controller for Lighting FL6961 Single-Stage Flyback and Boundary Mode PFC Controller for Lighting Features Boundary Mode PFC Controller Low Input Current THD Controlled On-Time PWM Zero-Current Detection Cycle-by-Cycle Current

More information

SN7500xP. Description. Package Type. Features. Application. Ordering Information SOP-16 DIP-16. Nov, 2011 REV. 00

SN7500xP. Description. Package Type. Features. Application. Ordering Information SOP-16 DIP-16. Nov, 2011 REV. 00 Pulse Width Modulation Description The SN7500 is a monolithic integrated circuit which includes all the necessary building blocks for the design of pulse width modulate(pwm) switching power supplies, including

More information

LM5034 High Voltage Dual Interleaved Current Mode Controller with Active Clamp

LM5034 High Voltage Dual Interleaved Current Mode Controller with Active Clamp High Voltage Dual Interleaved Current Mode Controller with Active Clamp General Description The dual current mode PWM controller contains all the features needed to control either two independent forward/active

More information

REI Datasheet. UC494A, UC494AC, UC495A, UC495AC Advanced Regulatin Pulse Width Modulators. Quality Overview

REI Datasheet. UC494A, UC494AC, UC495A, UC495AC Advanced Regulatin Pulse Width Modulators. Quality Overview UC494A, UC494AC, UC495A, UC495AC Advanced Regulatin Pulse Width Modulators REI Datasheet This entire series of PWM modulators each provide a complete pulse width modulation system in a single monolithic

More information

SG6561/A DESCRIPTION. APPLICATIONS Electronic Lamp Ballasts AC-DC Switching Mode Power Converters TYPICAL APPLICATION. Product Specification

SG6561/A DESCRIPTION. APPLICATIONS Electronic Lamp Ballasts AC-DC Switching Mode Power Converters TYPICAL APPLICATION. Product Specification FEATURES Boundary Mode PFC Controller Low Input Current THD Controlled On-Time PWM Zero-Current Detection Cycle-by-Cycle Current Limiting Leading-Edge Blanking instead of RC Filtering Fast Current Sense

More information

Rad-Tolerant Current Mode PWM Controller

Rad-Tolerant Current Mode PWM Controller SGR1844 / SGR1845 Rad-Tolerant Current Mode PWM Controller Description The SGR1844/SGR1845 is fit, form and function compatible to the SG1844/SG1845 with the addition of guaranteed performance after radiation

More information

FAN2013 2A Low-Voltage, Current-Mode Synchronous PWM Buck Regulator

FAN2013 2A Low-Voltage, Current-Mode Synchronous PWM Buck Regulator FAN2013 2A Low-Voltage, Current-Mode Synchronous PWM Buck Regulator Features 95% Efficiency, Synchronous Operation Adjustable Output Voltage from 0.8V to V IN-1 4.5V to 5.5V Input Voltage Range Up to 2A

More information

LD7536R 05/11/2010. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features.

LD7536R 05/11/2010. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features. 05/11/2010 Green-Mode PWM Controller with Frequency Swapping and Integrated Protections Rev. 00 General Description The LD7536R is built-in with several functions, protection and EMI-improved solution

More information

Dual Channel PWM Controller with SCP / DTC Function

Dual Channel PWM Controller with SCP / DTC Function Dual Channel PWM Controller with SCP / DTC Function General Description The FP545A is a dual channel PWM buck controller with short circuit protection (SCP) and adjustable maximum duty control (DTC) function.

More information