TFS / KFSU: Isolating spark gaps with plastic coating and 2 connections (Rd 10 mm) made of stainless

Transcription

1 LIGHTNING EQUIPOTENTIAL BONDING Isolating Spark Gap For lightning equipotential bonding For indirect connection/earthing of functionally isolated installation components when being affected by lightning For lightning equipotential bonding application according to IEC With corrosion-resistant stainless steel connections For mounting inside of buildings, outdoors, in damp rooms as well as for underground installation Extremely heavy-duty devices For lightning equipotential bonding according to IEC as well as for use in IT installations according to IEC TFS: High-capacity isolating spark gap KFSU: Isolating spark gap TFS / KFSU TFS KFSU TFS Isolating Spark Gap KFSU Ex- Isolating Spark Gap Dimension drawing TFS / KFSU Basic circuit diagram TFS / KFSU TFS / KFSU: Isolating spark gaps with plastic coating and 2 connections (Rd 10 mm) made of stainless steel Lightning impulse current (10/350 μs) I imp 100 ka Class of lightning current carrying capability acc. to EN H Nominal discharge current (8/20 μs) I n 100 ka 100 ka Rated power-frequency withstand voltage (50 Hz) U W/AC 300 V 300 V 100% Lightning impulse sparkover voltage U rimp 4 kv 4 kv Power frequency sparkover voltage (50 Hz) U aw 2.5 kv 2.5 kv Operating temperature range T U -20 C C -20 C C Degree of protection IP 65 IP 65 Length 160 mm 160 mm Diameter of enclosure 43 mm 43 mm Enclosure material steel-plastic coating steel-plastic coating Connection Rd 10 mm Rd 10 mm Material (connection) stainless steel stainless steel Type TFS KFSU Part No Packing unit 1 pc(s). 1 pc(s). TFS KFSU 343

2 EXFS 100 / EXFS 100 KU For explosion-hazard areas LIGHTNING EQUIPOTENTIAL BONDING For indirect connection/earthing of functionally isolated installation components when being affected by lightning Device for lightning equipotential bonding according to IEC in explosion-hazard areas For bridging insulating pieces, insulating flanges etc. in cathodically corrosion-protected pipe sections For safe installation in explosion protected zone 1 (gas) or 21 (dust) Especially low sparkover voltage Especially high a.c. current withstand capability ATEX-certified isolating spark gap for lightning equipotential bonding according to IEC with low sparkover voltage EXFS 100: Isolating spark gap for use in explosion-hazard areas with plastic coating and M10 connecting thread nut EXFS 100 KU: Isolating spark gap for use in explosion-hazard areas with 2 m connecting cable for underground installation The Ex isolating spark gaps of the EXFS 100 / EXFS 100 KU product family are used when conductive installation components situated in explosion-hazard areas cannot be connected directly with each other. The spark gaps with low sparkover voltage are especially efficient for isolated installation components with little insulation resistance. No special regulations have to be observed for safe application in zone 1 with gases or zone 21 with dusts. With a maximum lightning impulse current of 100 ka (10/350 μs), EXFS 100 and EXFS 100 KU meet class H according to EN Lightning Protection Components (LPC) Part 3: Requirements for isolating spark gaps. The ATEX-certified spark gaps EXFS 100 and EXFS 100 KU provide approved safety according to harmonised European standards. For connecting EXFS 100 spark gaps, prewired connecting cables with different lengths are available as accessories. Flat and angled connection brackets (IF) make it easier to connect the spark gaps to pipe flanges. EXFS 100 KU types are enclosed by a damp-proof plastic coating and can therefore be ideally used for underground installation at insulating couplings. Type examination certificate 344

3 EXFS 100 LIGHTNING EQUIPOTENTIAL BONDING EXFS 100 / EXFS 100 KU EXFS 100 EXFS Dimension drawing EXFS 100 Installation of EXFS 100 EXFS 100: Ex isolating spark gap with plastic coating and M10 connecting thread nuts EXFS 100 Lightning impulse current (10/350 μs) I imp 100 ka Class of lightning current carrying capability acc. to EN H Nominal discharge current (8/20 μs) I n 100 ka Rated power-frequency withstand voltage (50 Hz) U W/AC 250 V 100% Lightning impulse sparkover voltage U rimp 1.25 kv Power-frequency sparkover voltage (50 Hz) U aw 0.5 kv Rated discharge current (50 Hz) I max 500 A / 0.5 sec. (T U: 45 C) (Ex) marking acc. to EN (gases) II 2G Ex d IIC T6 (Ex) marking according to EN (dusts) II 2D Ex td A21 IP67 T 80 C Operating temperature range T U -20 C C Degree of protection IP 67 Approvals, Certifications BVS 06 ATEX E 099, IECEx KEM Length of enclosure 100 mm Diameter of enclosure 45,5 mm Enclosure material plastic coating Connection of enclosure thread nut M10, 2x M10x25 mm, 2x spring washer Type EXFS 100 Part No Packing unit 1 pc(s). Accessory Part for EXFS 100 / EXFS 100 KU Accessory Part for EXFS 100 / EXFS 100 KU EXFS 100: Connecting cable, Cu 25 mm 2 Connecting cable for EXFS 100; 2 cable lugs Ø10.5 mm, hexagon screw and nut (M10), StSt and spring washer Cable lug Cross Cable Type material section length pc(s). No. AL EXFS L100 KS Cu/gal Sn 25 mm mm AL EXFS L200 KS Cu/gal Sn 25 mm mm AL EXFS L300 KS Cu/gal Sn 25 mm mm AL EXFS L100 KS AL EXFS L200 KS AL EXFS L300 KS AL EXFS L100 KS AL EXFS L200 KS AL EXFS L300 KS Pair of angled connection brackets IF 1 Pair of angled connection brackets for EXFS...; diameter corresponds to bolt diameter of the bolted flange joint (d1 up to max. 60 mm, please indicate the diameter required when placing your order) Type Material pc(s). No. IF1 St/tZn Connection Bracket Type IF -SET Pair of flat connection brackets IF 3 Pair of flat connection brackets for EXFS...; diameter corresponds to bolt diameter of the bolted flange joint (d1 up to max. 60 mm, please indicated the diameter required when placing your order) Type Material pc(s). No. IF3 St/tZn Connection Bracket Type IF -SET

4 EXFS 100 / EXFS 100 KU EXFS 100 KU LIGHTNING EQUIPOTENTIAL BONDING EXFS 100 KU EXFS 100 KU isolating spark gap/ Funkenstrecke insulating piece/ Isolierstück insulation / Isolierung Installation of EXFS 100 KU Dimension drawing EXFS 100 KU EXFS 100 KU: Ex isolating spark gap with connecting cable for aboveground and underground installation EXFS 100 KU Lightning impulse current (10/350 μs) I imp 100 ka Class of lightning current carrying capability acc. to EN H Nominal discharge current (8/20 μs) I n 100 ka Rated power-frequency withstand voltage (50 Hz) U W/AC 250 V 100% Lightning impulse sparkover voltage U rimp 1.25 kv Power-frequency sparkover voltage (50 Hz) U aw 0.5 kv Rated discharge current (50 Hz) I max 500 A / 0.5 sec. (T U: 45 C) (Ex) marking acc. to EN (gases) II 2G Ex d IIC T6 (Ex) marking according to EN (dusts) II 2D Ex td A21 IP67 T 80 C Operating temperature range T U -20 C C Degree of protection IP 67 Approvals, Certifications BVS 06 ATEX E 099, IECEx KEM Length of enclosure 123 mm Diameter of enclosure 34 mm Enclosure material plastic coating; water-proof coating Connection of enclosure NYY-J-1x25 mm 2, approx. 2 m long Type EXFS 100 KU Part No Packing unit 1 pc(s)

5 LIGHTNING EQUIPOTENTIAL BONDING EXFS L / EXFS KU For use in explosion-hazard areas For indirect connection/earthing of functionally isolated installation components when being affected by lightning Device for lightning equipotential bonding acc. to IEC in explosion-hazard areas (Zone 2) According to ATEX Directive 94/9/EC Corrosion-resistant zinc diecasting enclosure with plastic cover and flexible conductor connection For bridging insulating pieces, insulating flanges etc. in cathodically corrosion protected pipe sections Extremely heavy-duty device ATEX-certified isolating spark gap for lightning equipotential bonding according to IEC 62305, approved device with flexible conductor connection EXFS L...: Isolating spark gap for use in explosion-hazard areas with flexible connecting cable EXFS KU: Isolating spark gap for use in explosion-hazard areas with 1.5 m connecting cable for underground installation Ex isolating spark gaps of the EXFS L / EXFS KU product family are used when the direct interconnection of electrically conductive installation components in Ex areas is not applicable. As, for example, in case of cathodically corrosion protected pipeline sections. ATEX-certified EXFS L and EXFS KU spark gaps provide approved and tested safety in accordance with harmonised European standards. The arc-resistant tungsten-copper electrodes ensure a long service life of the Ex spark gaps. The approved type EXFS L with flexible conductor connection quickly adapts to any application environment. The prewired spark gaps provide connecting cables with different lengths with cable lugs, screws and M10 nut. The flat or angled connection brackets (IF), which are available as accessories, allow for easy connection of the spark gap to pipeline flanges. The EXFS KU type is enclosed in a damp-proof PVC enclosure and is ideal for underground installation at insulating couplings

6 EXFS L / EXFS KU EXFS L LIGHTNING EQUIPOTENTIAL BONDING EXFS L EXFS L EXFS L300 EXFS L100 Ex- Isolating Spark Gap EXFS L200 Ex- Isolating Spark Gap EXFS L300 Ex- Isolating Spark Gap l max = 300 mm (avoid loops where possible) Installation of EXFS Dimension drawing EXFS EXFS L...: Ex isolating spark gap for aboveground installation EXFS L100 EXFS L200 EXFS L300 Lightning impulse current (10/350 μs) I imp 50 ka 50 ka 50 ka Class of lightning current carrying capability acc. to EN N N N Nominal discharge current (8/20 μs) I n 100 ka 100 ka 100 ka Rated power-frequency withstand voltage (50 Hz) U W/AC 300 V 300 V 300 V 100% Lightning impulse sparkover voltage U rimp 2.5 kv 2.5 kv 2.5 kv Power frequency sparkover voltage (50 Hz) U aw 1.2 kv 1.2 kv 1.2 kv Type of protection acc. to EN 50014, EN II 3 G EEx nc II T4 II 3 G EEx nc II T4 II 3 G EEx nc II T4 Operating temperature range T U -20 C C -20 C C -20 C C Degree of protection IP 54 IP 54 IP 54 Approvals, Certifications ZELM 03 ATEX 3192X ZELM 03 ATEX 3192X ZELM 03 ATEX 3192X Length of enclosure 90 mm 90 mm 90 mm Diameter of enclosure 63 mm 63 mm 63 mm Enclosure material zinc diecasting, plastic zinc diecasting, plastic zinc diecasting, plastic Connecting cable H01N2-D 25 mm 2 with cable lug and screw/nut (M10) Cable length 100 mm 200 mm 300 mm Suitable for flange size mm mm mm Type EXFS L100 EXFS L200 EXFS L300 Part No Packing unit 1 pc(s). 1 pc(s). 1 pc(s). Accessory Part for EXFS L / EXFS KU Pair of angled connection brackets IF 1 Pair of angled connection brackets for EXFS...; diameter corresponds to bolt diameter of the bolted flange joint (d1 up to max. Connection Bracket Type IF -SET mm, please indicate the diameter required when placing your order) Type Material pc(s). No. IF1 St/tZn Accessory Part for EXFS L / EXFS KU Pair of flat connection brackets IF 3 Pair of flat connection brackets for EXFS...; diameter corresponds to bolt diameter of the bolted flange joint (d1 up to max. Connection Bracket Type IF -SET mm, please indicated the diameter required when placing your order) Type Material pc(s). No. IF3 St/tZn

7 EXFS KU LIGHTNING EQUIPOTENTIAL BONDING EXFS L / EXFS KU EXFS KU EXFS KU Ex- Isolating Spark Gap Dimension drawing EXFS KU EXFS KU: Ex isolating spark gap with connecting cables for aboveground and underground installation EXFS KU Lightning impulse current (10/350 μs) I imp 50 ka Class of lightning current carrying capability acc. to EN N Nominal discharge current (8/20 μs) I n 100 ka Rated power-frequency withstand voltage (50 Hz) U W/AC 300 V 100% Lightning impulse sparkover voltage U rimp 2.5 kv Power frequency sparkover voltage (50 Hz) U aw 1.2 kv Type of protection acc. to EN 50014, EN II 3 G EEx nc II T4 Operating temperature range T U -20 C C Degree of protection IP 67 Approvals, Certifications ZELM 03 ATEX 3192X Length of enclosure 90 mm Diameter of enclosure 63 mm Enclosure material zinc diecasting, plastic Connecting cable NYY-J-1x25 mm 2 Cable length 2 x approx mm Type EXFS KU Part No Packing unit 1 pc(s)

8 Pipe Clamp for Explosion Hazard Areas LIGHTNING EQUIPOTENTIAL BONDING For fixing at pipes in explosion hazard areas For use in explosion hazard areas Ex zones 1 and 2 (gases, vapours, fogs) as well as Ex zones 21 and 22 (dusts) Tested for explosion group IIB Time-saving installation deactivation of the system/areas for welding or drilling work not necessary Pipe clamp for explosion hazard areas from Ø26.9 mm ( ) to Ø88.9 mm (3 ); Ø88.9 mm (3 ) to 300 mm and from Ø300 to 500 mm. Separate clamping body for endless tightening strap (Part No ) from Ø26.9 mm ( ) to 500 mm. Pipe clamp for electrical contacting of pipes in explosion hazard areas, for implementing of lightning equipotential bonding according to EN (VDE ) So far, the method of choice for implementing equipotential bonding and lightning equipotential bonding terminals in explosion hazard areas has been welding or threaded bushings. Using pipe clamps was only permitted if there was proof of ignition spark immunity in case of lightning current loading. DEHN + SÖHNE has now provided evidence of ignition spark absence for a pipe clamp at lightning current loading. By realising the test according to EN (VDE ): Requirements for connection components (clamps and connectors) in a potentially explosive atmosphere, absence of ignition sparks was proved for the test sample with a lightning current carrying capability up to 50 ka (10/350 μs). The design of this novel pipe clamp for explosion risk areas not only provides a safe electrical contact by means of two contact clips, but also the mechanical fixing by an electrically insulated clamping body. The Ex pipe clamp can be connected by round conductor, Cu, St/tZn, Al, StSt with Ø8/10 mm or flexible / stranded copper conductors, cross section mm 2, with E-Cu crimped cable lug (DIN 46235) flat copper conductor with minimum dimension 20x2.5 mm and a Ø10.5 mm bore hole DECLARATION OF MANUFACTURER Product: Pipe clamp for explosive zones Product description: Part No Part No Part No Part No Part No Manufacturer: DEHN + SÖHNE GmbH + Co.KG. Hans-Dehn-Str Neumarkt i.d.opf., Germany Application: The pipe clamp for explosive zones is used for connecting pipes of different materials and diameters to the lightning equipotential bonding structure in explosive atmospheres. Lightning currents are discharged without formation of sparks as specified in the technical data sheet. We herewith confirm that the pipe clamp for explosive zones is suitable for the use in explosive zones 1 and 2 (gas, vapour, mist) and explosive zones 21 and 22 (combustible dust) in connection with the installation instructions, P not legally admissible and not necessary with respect to explosion protection. Attached to a StSt pipe Neumarkt i.d.opf., 12 Okt Dr.-Ing. Ralph Brocke Director R&D c:\dokume~1\drb\lokale~1\temp\xpgrpwise\herstellererklärung bandrohrschelle ex-bereiche upd ate ausführung klein und groß engl..doc Page

9 EX BRS 27 LIGHTNING EQUIPOTENTIAL BONDING Pipe Clamp for Explosion Hazard Areas Ex Pipe Clamp for Ø6 mm to 26.9 mm EX BRS Type EX BRS 27 clamping range from Ø6 mm to 26.9 mm ( ) EX BRS 27 Lightning impulse current (10/350 μs) for Cu I imp 10 ka-> Ø6-12 mm I 20 ka-> Ø mm ( ) I 25 ka-> Ø26.9 mm ( ) Lightning impulse current (10/350 μs) for St/tZn I imp 25 ka-> Ø mm ( ) Lightning impulse current (10/350 μs) for StSt I imp 10 ka-> Ø6-12 mm I 12 ka-> Ø mm ( ) I 25 ka-> Ø26.9 mm ( ) Clamping range Ø mm ( ) Dimension tensioning strap (l1 x w x d) 190x10x0.25 mm Clamping body material polyamide Grip head/strap material StSt Contact angle material Ms/gal Sn Type EX BRS 27 Part No Packing unit 1 pc(s) Ex Pipe Clamp for Ø26.9 mm to 500 mm Type EX BRS 90, Part No , clamping range from Ø26.9 mm ( ) to 88.9 mm (3 ) Type EX BRS 300, Part No , clamping range from Ø88.9 mm (3 ) to 300 mm and Type EX BRS 500, Part No , clamping range from Ø300 to 500 mm EX BRS 90 EX BRS 300 EX BRS 500 Lightning impulse current (10/350 μs) for Cu I imp 50 ka 50 ka 50 ka Lightning impulse current (10/350 μs) for St/tZn I imp 50 ka 50 ka 50 ka Lightning impulse current (10/350 μs) for StSt I imp 25 ka 50 ka 50 ka Class of lightning current carrying capability acc. to DIN EN N N N Clamping range Ø26.9 ( ) mm (3 ) Ø88.9 (3 ) mm Ø mm Dimension tensioning strap (l1 x w x d) 410x25x0.3 mm 1100x25x0.3 mm 1850x25x0.3 mm Clamping body material polyamide polyamide polyamide Grip head/strap material StSt StSt StSt Contact angle material Cu/gal Sn Cu/gal Sn Cu/gal Sn Type EX BRS 90 EX BRS 300 EX BRS 500 Part No Packing unit 1 pc(s). 1 pc(s). 1 pc(s). NEW 351

10 Pipe Clamp for Explosion Hazard Areas Separate clamping body for endless tightening strap LIGHTNING PROTECTION TECHNOLOGY SYSTEMS Separate clamping body with endless strap (Part No ) Clamping ranges from Ø26.9 mm ( ) to 500 mm Lightning impulse current (10/350 μs) for Cu I imp Lightning impulse current (10/350 μs) for St/tZn I imp Lightning impulse current (10/350 μs) for StSt I imp Class of lightning current carrying capability acc. to DIN EN Clamping range Clamping body material Grip head/strap material Contact angle material 50 ka 50 ka 25 ka N Ø26.9 mm ( ) mm polyamide StSt Cu/gal Sn Part No Packing unit 1 pc(s). Accessory Part for Pipe Clamp for Explosion Hazard Areas Tensioning strap Endless tensioning strap (100 m long) Strap dimension Material (l x w x d) pc(s). No. StSt (V2A)... x 25 x 0.3 mm

11 LIGHTNING EQUIPOTENTIAL BONDING SDS Voltage Limiting Device Electrical isolation of insulated track sections and earthed parts of installations Safe equipotential bonding in case of a short circuit or earth fault at the overhead contact line due to high-current-resistant welding of the electrodes Discharge of surges without formation of short circuits due to lightning-resistant SDS... voltage limiting device Short-circuit withstand capability 25 ka rms / 100 ms; 36 ka rms / 75 ms SDS...: Cylindrical SDS spark gap unit for insertion into rail adapter Siemens No. 8WL6503-xx DIN EN describes the use of voltage limiting devices for d.c. and a.c. railways for so-called open earthing of railways for live components of overhead contact lines and current collectors. In order to prevent the occurrence of hazardous surges between the insulated tracks or track sections of electrical railways and earthed parts of the installation, voltage limiting devices (SDS...) are used. Their function is to connect parts of the installation in overhead contact lines and current collectors permanently to the return circuit, as soon as the threshold voltage is exceeded. In case of atmospheric overvoltages, the lightning-resistant SDS... voltage limiting device is capable of returning to its initial state after discharging the impulse current. Only if the specified lightning current loads are exceeded, a permanent short circuit is initiated by heavy-current-resistant welding of the electrodes and the fuse link has to be replaced. mostly unnecessary SDS spark gap unit for use with rail adapter, Siemens No. 8WL6503-xx The SDS voltage limiting device consists of a spark gap unit and the respective connecting kit for direct connection to the rail or overhead contact line tower. The spark gap unit type SDS 1, Part No , developed by DEHN + SÖHNE, has also been approved by the German Federal Railway Authority (EBA)

12 SDS SDS... LIGHTNING EQUIPOTENTIAL BONDING SDS 1 SDS 1 Sicherungseinsatz SDS Basic circuit diagram SDS... Dimension drawing SDS... SDS 1 SDS 2 SDS 3 SDS 4 SDS 5 Power frequency sparkover voltage U aw 940 V d.c. sparkover voltage U ag 600 V +/- 20 % 350 V +/- 20 % 550 V 230 V +/- 20 % 120 V +/- 20 % Impulse sparkover voltage 1400 V (1 kv/μs) 900 V (1 kv/μs) 1000 V (1 kv/μs) 650 V (1 kv/μs) 600 V (1 kv/μs) Self-extinguishing capability 300 A / 65 V Lightning current discharge capacity (10/350 μs) 0.1x / 0.5x / 1x 5 ka 2 ka 2.5 ka 2.5 ka 2 ka Lightning current withstand capability (10/350 μs) 25 ka 25 ka 25 ka 25 ka 25 ka Impulse current discharge capacity (8/20 μs) 0.1x / 0.5x / 1x 20 ka 20 ka Safe short circuit due to welding of the electrodes for alternating 100 ms 1.5 ka / 1000 V / 100 ms Safe short circuit due to welding of the electrodes for alternating 30 ms 2.5 ka / 1000 V / 30 ms Safe short circuit due to welding of the electrodes for direct currents 750 A / 250 ms 600 A / 250 ms 600 A / 250 ms 600 A / 250 ms Short circuit withstand capability 25 ka rms / 100 ms; 25 ka rms / 100 ms; 25 ka rms / 100 ms; 25 ka rms / 100 ms; 25 ka rms / 100 ms; 36 ka rms / 75 ms 36 ka rms / 75 ms 36 ka rms / 75 ms 36 ka rms / 75 ms Long-term current 1 ka rms for t 120 s 1 ka rms for t 120 s 1 ka rms for t 120 s 1 ka rms for t 120 s Leakage current I lc < 1 μa for 100 V d.c. < 1 μa for 100 V d.c. < 1 μa for 100 V d.c. < 1 μa for 100 V d.c. Operating temperature range T U -40 C C -40 C C -40 C C -40 C C -40 C C For mounting on allows for installation into voltage breakdown protector/siemens rail adapter No. 8WL6503-xx Tightening torque of the fuse link in the busbar adapter 15 Nm 15 Nm 15 Nm 15 Nm 15 Nm Approvals, Certifications EBA DB Drawing No. 4 Ebs Sheet 2 Type SDS 1 SDS 2 SDS 3 SDS 4 SDS 5 Part No Packing unit 10 pc(s). 10 pc(s). 10 pc(s). 10 pc(s). 10 pc(s)

13 LIGHTNING EQUIPOTENTIAL BONDING Equipotential Bonding Equipotential Bonding Bars PAS 11AK PAS 11AK Busbar PAS 11AK UV PAS 11AK UV AK FL40 PAS AK FL40 PAS Terminal for Fl PAS 9AK PAS 9AK Busbar Equipotential busbar K12, with snap-on terminals For equipotential bonding according to DIN VDE 0100 Part 410/540 and the lightning equipotential bonding according to EN (VDE ) Type K12 with 12 contact studs: 10 terminals for Rd mm 2 or Rd 10 mm conductors and 1 terminal for Fl -30x4 mm conductors Contact Cross Type bar section pc(s). No. PAS 11AK Cu/gal Sn 30 mm Type K12 with 12 contact studs, UV-stabilised: 10 terminals for Rd mm 2 or Rd 10 mm conductors and 1 terminal for Fl 30x4 mm Contact Cross Type bar section pc(s). No. PAS 11AK UV Cu/gal Sn 30 mm Accessories Snap-on Terminal for Fl 40 Conductors Type pc(s). No. AK FL40 PAS Equipotential Bonding Bar MS For equipotential bonding Connections for: 7 Rd conductors Rd mm 2 1 Rd conductor 7 10 mm 1 Fl conductor 30x3.5 mm or Rd conductor 8 10 mm Contact Cross Type bar section pc(s). No. PAS 9AK Ms 50 mm PAS 6RK OH PAS 6RK OH Busbar Equipotential Bonding Bars R15, with Terminal Block System For main equipotential bonding according to DIN VDE 0100 Part 410/540 and lightning equipotential bonding according to EN (DIN VDE ) Type A: 7 terminal blocks mm 2 2 terminal blocks mm 2 or Rd 8 10 mm 1 terminal block Fl -30x4 mm Clamping Cross Type bar section pc(s). No. PAS 10RK Ms/gal Sn 100 mm Type B: 5 terminal blocks mm 2 3 terminal blocks mm 2 or Rd 8 10 mm 1 terminal block Fl 30x4 mm Clamping Cross Type bar section pc(s). No. PAS 9RK Ms/gal Sn 100 mm Type C: 13 terminal blocks mm 2 1 terminal block mm 2 or Rd 8 10 mm Clamping Cross Type bar section pc(s). No. PAS 14RK Ms/gal Sn 100 mm Equipotential Bonding Busbar, with miniature terminal block system Miniature unit: For surface mounting without cover Clamping Cross Type bar Connection section pc(s). No. PAS 6RK OH Ms/gal Sn 6 x mm mm Accessories / Construction Kit RK FL40 PAS RK FL40 PAS Modular Terminal, flat strip -40 mm for EB Terminal Block Flat conductor 40 mm Type Material Connection Modules pc(s). No. RK FL40 PAS St/gal Zn -40x5 mm RK 16 PAS RK 16 PAS Modular Terminal, -16 mm for EB Terminal Block 2.5 to 25 mm 2 Type Material Connection Modules pc(s). No. RK 16 PAS St/gal Zn mm Terminal Block Up to 95 mm 2 or Rd 8-10 mm Type Material Connection Modules pc(s). No. RK 95 PAS St/gal Zn mm KS 198 PAS KS 398 PAS KS 798 PAS KS 198 PAS Terminal Bar, brass, 198 mm long KS 398 PAS Terminal bar, brass, 398 mm long KS 798 PAS Terminal bar, brass, 798 mm long SB PAS RK SB PAS RK Bar holder, plastic, grey Clamping Bar Type Material Length Modules pc(s). No. KS 198 PAS Ms/gal Sn 198 mm KS 398 PAS Ms/gal Sn 398 mm KS 798 PAS Ms/gal Sn 798 mm Bar Frame Fixing Type Material holes pc(s). No. SB PAS RK Plastic 6x4 mm RK FL30 PAS RK FL30 PAS Modular Terminal, flat strip -30 mm for EB Terminal Block Flat conductor 30 mm Type Material Connection Modules pc(s). No. RK FL30 PAS St/gal Zn -30x4 mm AH PAS RK AH PAS RK Plastic cover, grey Cover to snap on / to be labelled Type Material Modules pc(s). No. AH PAS RK Plastic Note: For our complete product range for earthing and equipotential bonding please refer to our current Lightning Protection catalogue, which can be requested from Export Department

14 Equipotential Bonding LIGHTNING EQUIPOTENTIAL BONDING Equipotential Bonding Bars for industial use Busbars PAS I 6AP M10 CU PAS I 6AP M10 V2A PAS I 6AP M10 CU Busbar PAS I 6AP M10 V2A Busbar PAS I 8AP M10 CU PAS I 8AP M10 V2A PAS I 8AP M10 CU Busbar PAS I 8AP M10 V2A Busbar PAS I 10AP M10 CU PAS I 10AP M10 V2A PAS I 10AP M10 CU Busbar PAS I 10AP M10 V2A Busbar PAS I 12AP M10 CU PAS I 12AP M10 V2A PAS I 12AP M10 CU PAS I 12AP M10 V2A Equipotential Bonding Busbar for industrial use For main equipotential bonding according to DIN VDE 0100 Part 410/540 and lightning equipotential bonding according to EN (DIN VDE ) Also for use in hazardous zones (screws protected against selfloosening) 6 connections with insulators Dimension Cross Type Material (l x w x d) section pc(s). No. PAS I 6AP M10 CU Cu 295x40x5 mm 200 mm PAS I 6AP M10 V2A StSt 295x40x6 mm 240 mm connections with insulators Dimension Cross Type Material (l x w x d) section pc(s). No. PAS I 8AP M10 CU Cu 365x40x5 mm 200 mm PAS I 8AP M10 V2A StSt 365x40x6 mm 240 mm connections with insulators Dimension Cross Type Material (l x w x d) section pc(s). No. PAS I 10AP M10 CU Cu 435x40x5 mm 200 mm PAS I 10AP M10 V2A StSt 435x40x6 mm 240 mm connections with insulators Dimension Cross Type Material (l x w x d) section pc(s). No. PAS I 12AP M10 CU Cu 505x40x5 mm 200 mm PAS I 12AP M10 V2A StSt 505x40x6 mm 240 mm ES 2X2AP 10 ST ES 2X2AP 10 V2A ES 2X2AP 10 Stk ES 2X2AP 10 V2A ES 2X3AP 10 ST ES 2X3AP 10 V2A ES 2X3AP 10 Stk ES 2X3AP 10 V2A ES 2X4AP ST ES 2X4AP 10 V2A ES 2X4AP Stk ES 2X4AP 10 V2A ES 2X6AP 10 ST ES 2X6AP 10 V2A ES 2X6AP 10 Stk ES 2X6AP 10 V2A Busbars To be screwed or welded to steel structures Borehole distance 50 mm 2x2 connections Dimension Cross Type Material (l x w x d) section pc(s). No. ES 2X2AP 10 ST St/tZn 196x60x4 mm 240 mm ES 2X2AP 10 V2A StSt 196x60x5 mm 300 mm x3 connections Dimension Cross Type Material (l x w x d) section pc(s). No. ES 2X3AP 10 ST St/tZn 242x60x4 mm 240 mm ES 2X3AP 10 V2A StSt 242x60x5 mm 300 mm x4 connections Dimension Cross Type Material (l x w x d) section pc(s). No. ES 2X4AP ST St/tZn 293x60x4 mm 240 mm ES 2X4AP 10 V2A StSt 293x60x5 mm 300 mm x6 connections Dimension Cross Type Material (l x w x d) section pc(s). No. ES 2X6AP 10 ST St/tZn 393x60x4 mm 240 mm ES 2X6AP 10 V2A StSt 393x60x5 mm 300 mm AD PAS 6AP V2A AD PAS 8AP V2A AD PAS 10AP V2A AD PAS 12AP V2A AD PAS 6AP V2A Cover NIRO, for 6-pole EB AD PAS 8AP V2A Cover NIRO, for 8-pole EB AD PAS 10AP V2A Cover NIRO, for 10-pole EB AD PAS 12AP V2A Cover NIRO, for 12-pole EB Accessories Cover for EBB (Industry) Covers for EBB with insulators Material EBB Dimension Type screw/nut type (l x w x d) pc(s). No. AD PAS 6AP V2A StSt 6 connections 301x60x0.8 mm AD PAS 8AP V2A StSt 8 connections 371x60x0.8 mm AD PAS 10AP V2A StSt 10 connections 441x60x0.8 mm AD PAS 12AP V2A StSt 12 connections 511x60x0.8 mm BS M10 PAS Accessories Fixing Set for EBB (Industry) BS M10 PAS Fixing Set for EB Screw Screw Plastic Type material type dowel pc(s). No. BS M10 PAS St/tZn 45 mm c M10x20 mm Ø12x60 mm IS PAS M10 Accessories Insulator for EBB (Industry) IS PAS M10 Isolator für PAS Industrie Material Terminal Type Isolator thread pc(s). No. IS PAS M10 UP (thermoset) M Note: For our complete product range for earthing and equipotential bonding please refer to our current Lightning Protection catalogue, which can be requested from Export Department

15 LIGHTNING EQUIPOTENTIAL BONDING Equipotential Bonding Connecting Clamps Components for ring equipotential bonding VK A UNI ST VK A UNI Stk. Connection Clamp St/tZn VK A UNI V2 ST VK A UNI V2 Stk. Connection Clamp St/tZn VK A R22 F40 STBL VK A R22 F40 STBL Connection Clamp St/bare MMVK R16 R25 ST MMVK R16 R25 STBL MMVK R16 R25 Stk. MAXI MV terminal, St/bare MMVK R16 R25 STBL MAXI MV terminal, St/tZn Connecting Clamp, for reinforcements For connecting reinforced concrete mats or reinforcements to round and flat conductors For T, cross and parallel connections Clamping range Type Material Rd / Rd Rd / Fl Fl / Fl pc(s). No. VK A UNI ST St/tZn (+) 6-10 / (+) 6-10 / (II) 30 / mm 30 mm 30 mm For T, cross and parallel connections Clamping range Type Material Rd / Fl Fl / Fl pc(s). No. VK A UNI V2 ST St/tZn (+) 6-10 / (+ / II) 30 / mm 30 mm For T and cross connections Clamping range Type Material Rd / Fl pc(s). No. VK A R22 F40 STBL St/bare (+) 6-22 / 40 mm MAXI MV Clamp for T, cross and parallel connections Part No with UL certification Clamping range Type Material Rd/Rd pc(s). No. MMVK R16 R25 ST St/tZn (+/II) 8-16 / mm MMVK R16 R25 STBL St/bare (+/II) 8-16 / mm Tape Conductors with Pressure Plate AK RPA V2A AK RPA V2A Strip Holder, with thrust pad For wall mounting Thrust pad with M8 screw for strip conductor up to 11 mm and round conductor 6-10 mm. 11 mm distance from the wall Material Material Type CH screw pc(s). No. FBH 6 ST St/tZn StSt FBH 6 CU Cu StSt FBH 6 V2A StSt StSt mm distance from the wall Material Material Type CH screw pc(s). No. FBH 11 ST St/tZn StSt Terminal Clamp For universal connection to the ring equipotential bonding for St/tZn, copper or stainless steel (StSt) CH Cross-sectional Type Material Rd / Fl area pc(s). No. AK RPA V2A StSt 8-10 / 3-11x30 mm mm Components for foundation earthing electrodes VK EH R10 F30 ST VK EH R10 F30 V2A VK EH R10 F30 Stk. Connection Clamp St/tZn VK EH R10 F30 V2A Connection Clamp StSt (V2A) Connecting Clamp, for Foundation Earth Electrodes For connecting round and flat conductors in the concrete foundation For T, cross and parallel connections, no threading of the conductors required Clamping range mm Type Material Rd / Fl Fl / Fl pc(s). No. VK EH R10 F30 ST St/tZn (+) 10 / 30 (+/II) 30 / VK EH R10 F30 V2A StSt (+) 10 / 30 (+/II) 30 / Expansion Strap for Foundation Earth Electrodes For leading the foundation earth electrode in extended foundations (several sections) through the expansion or isolating joints. Thus no need to lead the earth electrode out of the base plate. Strap Dimension Block material (l x w x d) material pc(s). No. StSt (V2A) approx. 700x30x(4x1) mm styrene AH FE RF V G AH FE RF V G Distance Holder St/tZn, reinf. version 300 mm AH FE RF AH FE RF Distance Holder St/tZn, DIN A, 280 mm Spacer Reinforced angled type Support Support Type Material Fl Rd pc(s). No. AH FE RF V G St/tZn 40 mm 8-10 mm Spacer Straight type Support Support Type Material Fl Rd pc(s). No. AH FE RF St/tZn 40 mm 8-10 mm Note: For our complete product range for earthing and equipotential bonding please refer to our current Lightning Protection catalogue, which can be requested from Export Department

16 358