SIMULATIONS OF LCC RESONANT CIRCUIT POWER ELECTRONICS COLORADO STATE UNIVERSITY. Modified in Spring 2006
|
|
|
- Charleen Williamson
- 6 years ago
- Views:
Transcription
1 SIMULATIONS OF LCC RESONANT CIRCUIT POWER ELECTRONICS COLORADO STATE UNIVERSITY Modified in Spring 2006 Page 1 of 27
2 PURPOSE: The purpose of this lab is to simulate the LCC circuit using MATLAB and CAPTURE CIS to better familiarize the student with some of its operating characteristics. This lab will explore some of the following aspects of the buck converter: Input impedance Output impedance Zero frequency Output power Output current Output voltage Zero poles Phase of transfer function Stable circuit Unstable circuit Simulation of LCC Resonant Circuit Using CAPTURE CIS NOTE: The simulations that follow are intended to be completed with CAPTURE CIS. It is assumed that the student has a fundamental understanding of the operation of CAPTURE CIS. CAPTURE CIS provides tutorials for users that are not experienced with its functions. PROCEDURE: Part 1: Build the schematic shown in Figure below. Vm is an AC voltage source (VAC) from the source library. It needs to be set for 1 volt. L1 is an ideal inductor from the Analog Library. Set for 25µH. R is an ideal resistor from the Analog Library. Set for 25. Page 2 of 27
3 Cs is an ideal capacitor from the Analog library. Change the value to 200nF. Cp is an ideal capacitor from the Analog library. Change the value to 66nF. Use the student version Capture CIS that install on CSU computer lab to simulation the given circuit above. Here are some steps: 1. Draw the circuit given above 2. Apply the VAC, because we want to plot the frequency response 3. Do analysis setup a. Go to analysis/setup b. D-click on AC sweep c. Set all the values for the frequency as following d. And click on decade Page 3 of 27
4 Click OK 4. Analysis/run probe The figure below is the result of impedance of series RLC tank circuit. What is the input impedance value of LCC circuit? Page 4 of 27
5 Next, we want to run the simulation of the output voltage of the LCC circuit. Use the same circuit as above, and place voltage markers as shown in the schematic below. This figure shows the output voltage of LCC circuit. What is the output voltage of LCC circuit? Page 5 of 27
6 Now remove voltage markers from the circuit, and place the db magnitude of voltage marker in series next to output resistor. The figure below is the result of output voltage of series LCC tank circuit. What is the value of output voltage of LCC circuit? What is the phase value output voltage of LCC circuit? Page 6 of 27
7 Use the same circuit as above and remove the db magnitude of voltage marker from the circuit. Place the db magnitude of current marker and the Phase of current in series next to L1. Page 7 of 27
8 The figure below is the result of inductor current of series LCC tank circuit. What is the value of inductor current of LCC circuit? What is the phase value of inductor current of LCC circuit? Next, find the zero crossing of phase of inductor current. Use the same circuit as above and remove the db magnitude of current marker from the circuit. Keep the Phase of current in series next to L1. Page 8 of 27
9 The figure below is the result of zero crossing of phase of inductor current of series LCC tank circuit. What is the value the zero crossing of phase of inductor current? Page 9 of 27
10 Use the same circuit as above and remove the db magnitude of current marker and Phase of current from the inductor. Place the db magnitude of current marker and the Phase of current in series next to Cs. The figure below is the result of capacitor current of series LCC tank circuit. What is the value of input capacitor Cs current of LCC circuit? What is the phase value of input capacitor (Cs) current of LCC circuit? Use the same circuit as above and remove the db magnitude of current marker and Phase of current from the input capacitor (Cs). Place the db Page 10 of 27
11 magnitude of current marker in series next to output resistor. The figure below is the result of power of series LCC tank circuit. What is the value of power of LCC circuit? For Homework: You need to re-solve the LCC resonant circuit with Capacitor ESR and see its effects on the magnitude and phase plots in some detail. For example choose the ratio of the Cs and Cp ESR to the load resistance to be in the ratio range from 0.01 to 1. Page 11 of 27
12 Simulation of LCC Resonant Circuit Using MATLAB NOTE: The simulations that follow are intended to be completed with MATLAB. It is assumed that the student has a fundamental understanding of the operation of MATLAB. MATLAB provides tutorials for users that are not experienced with its functions. PROCEDURE: Part 1: write an m file shown in Figure 1. Vm is a variable voltage. Set to 1 volts L is a variable inductor. Set to 25µH. R is a variable ideal resistor. Set to 25Ω. Cp is a variable ideal capacitor. Change the value to 66nF. Cs is a variable ideal capacitor. Change the value to 200nF. Page 12 of 27
13 Figure1. Input impedance for LCC circuit Page 13 of 27
14 Once the above m file is captured, the simulations can be run. First, go to your directory. Find your m file and then run your file. If there is a red message on your MATLAB window, then you need to correct your error. Otherwise, you will see the solution as show in figure 2. Page 14 of 27
15 Figure 2. The output of Zinput_LCC m file. Next, plot the output voltage of the LCC circuit by adding the output voltage equation to the LCC m file. Then rerun the LCC m file. Page 15 of 27
16 Page 16 of 27
17 Now plot the inductor current of the LCC circuit by adding the inductor current equations to the LCC m file. Then rerun the LCC m file. Page 17 of 27
18 Page 18 of 27
19 Page 19 of 27
20 Now find the zero crossing of phase of inductor current. First define the input impedance as a vector. Write a loop function to do the zero crossing of the phase. Then rerun the simulation. If there is any error message on your MATLAB windows, then correct your error and then rerun the simulation. Otherwise, you will see the result as show below Page 20 of 27
21 Page 21 of 27
22 Now calculate and plot the output of capacitor current by adding the capacitor current equations to the LCC m file. Then rerun the LCC m file. Then rerun the simulation. If there is any error message on your MATLAB windows, then correct your error and then rerun the simulation. Otherwise, you will see the results as show below Page 22 of 27
23 Page 23 of 27
24 Page 24 of 27
25 Now calculate and plot the output power of LCC circuit by adding the output power equations to the LCC m file. But the output power is a vector function. First define the input impedance as a vector. Write a loop function to do the zero crossing of the phase. Then rerun the LCC m file. If there is any error message on your MATLAB windows, then correct your error and then rerun the simulation. Otherwise, you will see the results as show below Page 25 of 27
26 Page 26 of 27
27 ans = Page 27 of 27
SIMULATION OF A SERIES RESONANT CIRCUIT ECE562: Power Electronics I COLORADO STATE UNIVERSITY. Modified in Fall 2011
SIMULATION OF A SERIES RESONANT CIRCUIT ECE562: Power Electronics I COLORADO STATE UNIVERSITY Modified in Fall 2011 ECE 562 Series Resonant Circuit (NL5 Simulation) Page 1 PURPOSE: The purpose of this
PSPICE SIMULATIONS WITH THE RESONANT INVERTER POWER ELECTRONICS COLORADO STATE UNIVERSITY. Created by Colorado State University student
PSPICE SIMULATIONS WITH THE RESONANT INVERTER POWER ELECTRONICS COLORADO STATE UNIVERSITY Created by Colorado State University student Page 1 of 13 PURPOSE: The purpose of this lab is to simulate the resonant
SIMULATIONS WITH THE BUCK-BOOST TOPOLOGY EE562: POWER ELECTRONICS I COLORADO STATE UNIVERSITY. Modified February 2006
SIMULATIONS WITH THE BUCK-BOOST TOPOLOGY EE562: POWER ELECTRONICS I COLORADO STATE UNIVERSITY Modified February 2006 Page 1 of 13 PURPOSE: The purpose of this lab is to simulate the Buck-Boost converter
SIMULATION WITH THE BOOST TOPOLOGY ECE562: Power Electronics I COLORADO STATE UNIVERSITY. Modified in Fall 2011
SIMULATION WITH THE BOOST TOPOLOGY ECE562: Power Electronics I COLORADO STATE UNIVERSITY Modified in Fall 2011 ECE 562 Boost Converter (NL5 Simulation) Laboratory 2 Page 1 PURPOSE: The purpose of this
EXPERIMENT NUMBER 10 TRANSIENT ANALYSIS USING PSPICE
EXPERIMENT NUMBER 10 TRANSIENT ANALYSIS USING PSPICE Objective: To learn to use a circuit simulator package for plotting the response of a circuit in the time domain. Preliminary: Revise laboratory 8 to
SIMULATION WITH THE CUK TOPOLOGY ECE562: Power Electronics I COLORADO STATE UNIVERSITY. Modified in Fall 2011
SIMULATION WITH THE CUK TOPOLOGY ECE562: Power Electronics I COLORADO STATE UNIVERSITY Modified in Fall 2011 ECE 562 Cuk Converter (NL5 Simulation) Laboratory Page 1 PURPOSE: The purpose of this lab is
SIMULATIONS WITH THE BOOST TOPOLOGY EE562: POWER ELECTRONICS I COLORADO STATE UNIVERSITY. Modified February 2006
SIMULATIONS WITH THE BOOST TOPOLOGY EE562: POWER ELECTRONICS I COLORADO STATE UNIVERSITY Modified February 26 Page 1 of 24 PURPOSE: The purpose of this lab is to simulate the Boost converter using ORCAD
DEPARTMENT OF ELECTRICAL ENGINEERING. Date: Assistant A2: PSpice 2 PC Pool
University of Applied Sciences Hamburg Group No : DEPARTMENT OF ELECTRICAL ENGINEERING Laboratory for Instrumentation and Measurement L1: in charge of the report PSpice 2 PC Pool Date: Assistant A2: Professor:
Lab 9 Frequency Domain
Lab 9 Frequency Domain 1 Components Required Resistors Capacitors Function Generator Multimeter Oscilloscope 2 Filter Design Filters are electric components that allow applying different operations to
RLC Frequency Response
1. Introduction RLC Frequency Response The student will analyze the frequency response of an RLC circuit excited by a sinusoid. Amplitude and phase shift of circuit components will be analyzed at different
BAKISS HIYANA BT ABU BAKAR JKE,POLISAS
BAKISS HIYANA BT ABU BAKAR JKE,POLISAS 1 1. Explain AC circuit concept and their analysis using AC circuit law. 2. Apply the knowledge of AC circuit in solving problem related to AC electrical circuit.
EE 2274 RC and Op Amp Circuit Completed Prior to Coming to Lab. Prelab Part I: RC Circuit
EE 2274 RC and Op Amp Circuit Completed Prior to Coming to Lab Prelab Part I: RC Circuit 1. Design a high pass filter (Fig. 1) which has a break point f b = 1 khz at 3dB below the midband level (the -3dB
Time Domain Reflectometer Example
Time Domain Reflectometer Example This section presents differential and single-ended versions of a Time Domain Reflectometer (TDR). The setup demonstrates the process of analyzing both imdepance and delay.
University of Jordan School of Engineering Electrical Engineering Department. EE 219 Electrical Circuits Lab
University of Jordan School of Engineering Electrical Engineering Department EE 219 Electrical Circuits Lab EXPERIMENT 7 RESONANCE Prepared by: Dr. Mohammed Hawa EXPERIMENT 7 RESONANCE OBJECTIVE This experiment
Introduction to Modeling of Switched Mode Power Converters Using MATLAB and Simulink
Introduction to Modeling of Switched Mode Power Converters Using MATLAB and Simulink Extensive introductory tutorials for MATLAB and Simulink, including Control Systems Toolbox and Simulink Control Design
AC Circuits INTRODUCTION DISCUSSION OF PRINCIPLES. Resistance in an AC Circuit
AC Circuits INTRODUCTION The study of alternating current 1 (AC) in physics is very important as it has practical applications in our daily lives. As the name implies, the current and voltage change directions
University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 4 SINGLE STAGE AMPLIFIER
University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 4 SINGLE STAGE AMPLIFIER Issued 10/27/2008 Report due in Lecture 11/10/2008 Introduction In this lab you will characterize a 2N3904 NPN
ETIN25 Analogue IC Design. Laboratory Manual Lab 2
Department of Electrical and Information Technology LTH ETIN25 Analogue IC Design Laboratory Manual Lab 2 Jonas Lindstrand Martin Liliebladh Markus Törmänen September 2011 Laboratory 2: Design and Simulation
Experiment Number 2. Revised: Summer 2013 PLECS RC, RL, and RLC Simulations
Preface: Experiment Number 2 Revised: Summer 2013 PLECS RC, RL, and RLC Simulations Preliminary exercises are to be done and submitted individually Laboratory simulation exercises are to be done individually
LAB1 WEBENCH SIMULATION EE562: POWER ELECTRONICS COLORADO STATE UNIVERSITY
LAB1 WEBENCH SIMULATION EE562: POWER ELECTRONICS COLORADO STATE UNIVERSITY PURPOSE: The purpose of this lab is to explore National Semiconductors WEBENCH, which is an online design and prototyping tool.
Microwave Circuit Design: Lab 5
1. Introduction Microwave Circuit Design: Lab 5 This lab investigates how trade-offs between gain and noise figure affect the design of an amplifier. 2. Design Specifications IMN OMN 50 ohm source Low
OrCAD 17.2 Pspice Tutorial. High-Speed Circuits & Systems Lab. Yonsei University
OrCAD 17.2 Pspice Tutorial High-Speed Circuits & Systems Lab. Yonsei University Installation Move to http://www.orcad.com/resources/orcaddownloads#demo Installation Click Download FREE-OrCAD 17.2 Lite
A Walk Through the MSA Software Vector Network Analyzer Transmission Mode 12/18/09
A Walk Through the MSA Software Vector Network Analyzer Transmission Mode 12/18/09 This document is intended to familiarize you with the basic features of the MSA and its software, operating as a Vector
EXPERIMENT 9 Problem Solving: First-order Transient Circuits
EXPERIMENT 9 Problem Solving: First-order Transient Circuits I. Introduction In transient analyses, we determine voltages and currents as functions of time. Typically, the time dependence is demonstrated
CHAPTER 6: ALTERNATING CURRENT
CHAPTER 6: ALTERNATING CURRENT PSPM II 2005/2006 NO. 12(C) 12. (c) An ac generator with rms voltage 240 V is connected to a RC circuit. The rms current in the circuit is 1.5 A and leads the voltage by
Lab 1: Basic RL and RC DC Circuits
Name- Surname: ID: Department: Lab 1: Basic RL and RC DC Circuits Objective In this exercise, the DC steady state response of simple RL and RC circuits is examined. The transient behavior of RC circuits
University of Michigan EECS 311: Electronic Circuits Fall 2009 LAB 2 NON IDEAL OPAMPS
University of Michigan EECS 311: Electronic Circuits Fall 2009 LAB 2 NON IDEAL OPAMPS Issued 10/5/2008 Pre Lab Completed 10/12/2008 Lab Due in Lecture 10/21/2008 Introduction In this lab you will characterize
Simulating Circuits James Lamberti 5/4/2014
Simulating Circuits James Lamberti (jal416@lehigh.edu) 5/4/2014 There are many simulation and design platforms for circuits. The two big ones are Altium and Cadence. This tutorial will focus on Altium,
EXPERIMENT NUMBER 8 Introduction to Active Filters
EXPERIMENT NUMBER 8 Introduction to Active Filters i-1 Preface: Preliminary exercises are to be done and submitted individually. Laboratory hardware exercises are to be done in groups. This laboratory
Department of Electrical & Computer Engineering Technology. EET 3086C Circuit Analysis Laboratory Experiments. Masood Ejaz
Department of Electrical & Computer Engineering Technology EET 3086C Circuit Analysis Laboratory Experiments Masood Ejaz Experiment # 1 DC Measurements of a Resistive Circuit and Proof of Thevenin Theorem
Study of Inductive and Capacitive Reactance and RLC Resonance
Objective Study of Inductive and Capacitive Reactance and RLC Resonance To understand how the reactance of inductors and capacitors change with frequency, and how the two can cancel each other to leave
Engineering 3821 Fall Pspice TUTORIAL 1. Prepared by: J. Tobin (Class of 2005) B. Jeyasurya E. Gill
Engineering 3821 Fall 2003 Pspice TUTORIAL 1 Prepared by: J. Tobin (Class of 2005) B. Jeyasurya E. Gill 2 INTRODUCTION The PSpice program is a member of the SPICE (Simulation Program with Integrated Circuit
FACULTY OF ENGINEERING LAB SHEET
FACULTY OF ENGINEERING LAB SHEET CIRCUITS AND SIGNALS EEL 2186 TRIMESTER 1 (218/219) -Circuit analysis using ORCAD PSpice *Note: You will be given an assessment sheet during the lab session to be completed
Experiment Number 2. Revised: Fall 2018 PLECS RC, RL, and RLC Simulations
Experiment Number 2 Revised: Fall 2018 PLECS RC, RL, and RLC Simulations Preface: Experiment number 2 will be held in CLC room 105, 106, or 107. Your TA will let you know Preliminary exercises are to be
Lab #2 First Order RC Circuits Week of 27 January 2015
ECE214: Electrical Circuits Laboratory Lab #2 First Order RC Circuits Week of 27 January 2015 1 Introduction In this lab you will investigate the magnitude and phase shift that occurs in an RC circuit
BUCK Converter Control Cookbook
BUCK Converter Control Cookbook Zach Zhang, Alpha & Omega Semiconductor, Inc. A Buck converter consists of the power stage and feedback control circuit. The power stage includes power switch and output
Experiment 8: An AC Circuit
Experiment 8: An AC Circuit PART ONE: AC Voltages. Set up this circuit. Use R = 500 Ω, L = 5.0 mh and C =.01 μf. A signal generator built into the interface provides the emf to run the circuit from Output
Figure AC circuit to be analyzed.
7.2(1) MULTISIM DEMO 7.2: INTRODUCTION TO AC ANALYSIS In this section, we ll introduce AC Analysis in Multisim. This is perhaps one of the most useful Analyses that Multisim offers, and we ll use it in
Opamp stability using non-invasive methods
Opamp stability using non-invasive methods Opamps are frequently use in instrumentation systems as unity gain analog buffers, voltage reference buffers and ADC input buffers as well as low gain preamplifiers.
Resonant Frequency of the LRC Circuit (Power Output, Voltage Sensor)
72 Resonant Frequency of the LRC Circuit (Power Output, Voltage Sensor) Equipment List Qty Items Part Numbers 1 PASCO 750 Interface 1 Voltage Sensor CI-6503 1 AC/DC Electronics Laboratory EM-8656 2 Banana
Background Theory and Simulation Practice
CAD and Simulation Objectives Experiment Topic: CAD and Simulation PSpice 9.1 Student Version To obtain your free copy of the software and user s guide, go to Electronics Lab website ( http://www.electronics-lab.com/downloads/schematic/013/
University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS
University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS Issued 9/22/2008 Pre Lab Completed 9/29/2008 Lab Due in Lecture 10/6/2008 Introduction In this lab you will design a
Exercise 2: Parallel RLC Circuits
RLC Circuits AC 2 Fundamentals Exercise 2: Parallel RLC Circuits EXERCSE OBJECTVE When you have completed this exercise, you will be able to analyze parallel RLC circuits by using calculations and measurements.
Frequency Selective Circuits
Lab 15 Frequency Selective Circuits Names Objectives in this lab you will Measure the frequency response of a circuit Determine the Q of a resonant circuit Build a filter and apply it to an audio signal
ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis
ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis All circuit simulation packages that use the Pspice engine allow users to do complex analysis that were once impossible to
ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits
ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits Laboratory Group (Names) OBJECTIVES Observe and calculate the response of first-order low pass and high pass filters. Gain
EECS40 RLC Lab guide
EECS40 RLC Lab guide Introduction Second-Order Circuits Second order circuits have both inductor and capacitor components, which produce one or more resonant frequencies, ω0. In general, a differential
The Series RLC Circuit and Resonance
Purpose Theory The Series RLC Circuit and Resonance a. To study the behavior of a series RLC circuit in an AC current. b. To measure the values of the L and C using the impedance method. c. To study the
Exercise 1: Series Resonant Circuits
Series Resonance AC 2 Fundamentals Exercise 1: Series Resonant Circuits EXERCISE OBJECTIVE When you have completed this exercise, you will be able to compute the resonant frequency, total current, and
A Walk Through the MSA Software Vector Network Analyzer Reflection Mode 12/12/09
A Walk Through the MSA Software Vector Network Analyzer Reflection Mode 12/12/09 This document is intended to familiarize you with the basic features of the MSA and its software, operating as a Vector
Series and Parallel Resonant Circuits
Series and Parallel Resonant Circuits Aim: To obtain the characteristics of series and parallel resonant circuits. Apparatus required: Decade resistance box, Decade inductance box, Decade capacitance box
Introduction to OrCAD. Simulation Program With Integrated Circuits Emphasis.
Islamic University of Gaza Faculty of Engineering Electrical Engineering department Digital Electronics Lab (EELE 3121) Eng. Mohammed S. Jouda Eng. Amani S. abu reyala Experiment 1 Introduction to OrCAD
Designing low-frequency decoupling using SIMPLIS
Designing low-frequency decoupling using SIMPLIS K. Covi Traditional approach to sizing decoupling Determine effective ESR required Parallel electrolytic caps until ESR = ΔV/ΔI where ΔV = desired voltage
Exercise 1: RF Stage, Mixer, and IF Filter
SSB Reception Analog Communications Exercise 1: RF Stage, Mixer, and IF Filter EXERCISE OBJECTIVE DISCUSSION On the circuit board, you will set up the SSB transmitter to transmit a 1000 khz SSB signal
Exercise 2: Q and Bandwidth of a Series RLC Circuit
Series Resonance AC 2 Fundamentals Exercise 2: Q and Bandwidth of a Series RLC Circuit EXERCISE OBJECTIVE When you have completed this exercise, you will be able to calculate the bandwidth and Q of a series
An Introductory Guide to Circuit Simulation using NI Multisim 12
School of Engineering and Technology An Introductory Guide to Circuit Simulation using NI Multisim 12 This booklet belongs to: This document provides a brief overview and introductory tutorial for circuit
Experiment Guide: RC/RLC Filters and LabVIEW
Description and ackground Experiment Guide: RC/RLC Filters and LabIEW In this lab you will (a) manipulate instruments manually to determine the input-output characteristics of an RC filter, and then (b)
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 8 FILTER NETWORKS OBJECTIVES In this lab session the student will investigate passive low-pass and
EK307 Active Filters and Steady State Frequency Response
EK307 Active Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of active signal-processing filters Learning Objectives: Active Filters, Op-Amp Filters, Bode plots Suggested
Lab E5: Filters and Complex Impedance
E5.1 Lab E5: Filters and Complex Impedance Note: It is strongly recommended that you complete lab E4: Capacitors and the RC Circuit before performing this experiment. Introduction Ohm s law, a well known
EE 462G Laboratory #1 Measuring Capacitance
EE 462G Laboratory #1 Measuring Capacitance Drs. A.V. Radun and K.D. Donohue (1/24/07) Department of Electrical and Computer Engineering University of Kentucky Lexington, KY 40506 Updated 8/31/2007 by
Foundations (Part 2.C) - Peak Current Mode PSU Compensator Design
Foundations (Part 2.C) - Peak Current Mode PSU Compensator Design tags: peak current mode control, compensator design Abstract Dr. Michael Hallworth, Dr. Ali Shirsavar In the previous article we discussed
Introduction to PSpice
Electric Circuit I Lab Manual 4 Session # 5 Introduction to PSpice 1 PART A INTRODUCTION TO PSPICE Objective: The objective of this experiment is to be familiar with Pspice (learn how to connect circuits,
CHAPTER 14. Introduction to Frequency Selective Circuits
CHAPTER 14 Introduction to Frequency Selective Circuits Frequency-selective circuits Varying source frequency on circuit voltages and currents. The result of this analysis is the frequency response of
ENGR4300 Test 3A Fall 2002
1. 555 Timer (20 points) Figure 1: 555 Timer Circuit For the 555 timer circuit in Figure 1, find the following values for R1 = 1K, R2 = 2K, C1 = 0.1uF. Show all work. a) (4 points) T1: b) (4 points) T2:
Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4
EECS 16B Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm 1,
ECE 4670 Spring 2014 Lab 1 Linear System Characteristics
ECE 4670 Spring 2014 Lab 1 Linear System Characteristics 1 Linear System Characteristics The first part of this experiment will serve as an introduction to the use of the spectrum analyzer in making absolute
Week 4: Experiment 24. Using Nodal or Mesh Analysis to Solve AC Circuits with an addition of Equivalent Impedance
Week 4: Experiment 24 Using Nodal or Mesh Analysis to Solve AC Circuits with an addition of Equivalent Impedance Lab Lectures You have two weeks to complete Experiment 27: Complex Power 2/27/2012 (Pre-Lab
ECE 6416 Low-Noise Electronics Orientation Experiment
ECE 6416 Low-Noise Electronics Orientation Experiment Object The object of this experiment is to become familiar with the instruments used in the low noise laboratory. Parts The following parts are required
EK307 Passive Filters and Steady State Frequency Response
EK307 Passive Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of passive signal-processing filters Learning Objectives: Passive filters, Frequency domain, Bode plots
OrCAD PSpice - Tutorial. TA: 黃玉龍
OrCAD PSpice - Tutorial TA: 黃玉龍 r9994320@ntu.edu.tw Outline 2 Introduction Preparation Schematic Simulation Conclusion Introduction 3 OrCAD PSpice is developed by Cadence Analog circuit simulation tool
Electronics and Instrumentation Name ENGR-4220 Fall 1998 Section Quiz 2
Quiz 2 1. RLC Circuits You should recognize the circuits shown below from Experiment 5 and Gingrich s notes. Given below are several possible expressions for transfer functions for such circuits. Indicate
Cir cuit s 212 Lab. Lab #7 Filter Design. Introductions:
Cir cuit s 22 Lab Lab #7 Filter Design The purpose of this lab is multifold. This is a three-week experiment. You are required to design a High / Low Pass filter using the LM38 OP AMP. In this lab, you
3. Apparatus/ Materials 1) Computer 2) Vernier board circuit
Experiment 3 RLC Circuits 1. Introduction You have studied the behavior of capacitors and inductors in simple direct-current (DC) circuits. In alternating current (AC) circuits, these elements act somewhat
Since transmission lines can be modeled using PSpice, you can do your analysis by downloading the student version of this excellent program.
PSpice Analysis Since transmission lines can be modeled using PSpice, you can do your analysis by downloading the student version of this excellent program. PSpice can be downloaded from the following
LAB 8: Activity P52: LRC Circuit
LAB 8: Activity P52: LRC Circuit Equipment: Voltage Sensor 1 Multimeter 1 Patch Cords 2 AC/DC Electronics Lab (100 μf capacitor; 10 Ω resistor; Inductor Coil; Iron core; 5 inch wire lead) The purpose of
Core Technology Group Application Note 6 AN-6
Characterization of an RLC Low pass Filter John F. Iannuzzi Introduction Inductor-capacitor low pass filters are utilized in systems such as audio amplifiers, speaker crossover circuits and switching power
Introduction to SPICE. Simulator of Electronic devices
Introduction to SPICE Simulator of Electronic devices Main steps: Download Instalation Open OrCAD capture CIS Lite Create a circuit. Place parts. Design a Simulation Profile Run PSpice F11 View simulation
ME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION
Objectives: ME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION The primary goal of this laboratory is to study the operation and limitations of several commonly used pieces of instrumentation:
INTRODUCTION TO FILTER CIRCUITS
INTRODUCTION TO FILTER CIRCUITS 1 2 Background: Filters may be classified as either digital or analog. Digital filters are implemented using a digital computer or special purpose digital hardware. Analog
Activity P52: LRC Circuit (Voltage Sensor)
Activity P52: LRC Circuit (Voltage Sensor) Concept DataStudio ScienceWorkshop (Mac) ScienceWorkshop (Win) AC circuits P52 LRC Circuit.DS (See end of activity) (See end of activity) Equipment Needed Qty
EE 210 Lab Exercise #3 Introduction to PSPICE
EE 210 Lab Exercise #3 Introduction to PSPICE Appending 4 in your Textbook contains a short tutorial on PSPICE. Additional information, tutorials and a demo version of PSPICE can be found at the manufacturer
DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER
DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER Murdoch University: The Murdoch School of Engineering & Information Technology Author: Jason Chan Supervisors: Martina Calais &
University of Illinois at Chicago Spring ECE 412 Introduction to Filter Synthesis Homework #2 Solutions. Problem 1
Problem 1 (a) Magnitude (impedance) scale the circuit so that all resistors are 1kΩ. Solution: Since all of the resistors in the circuit are 1Ω, we need to magnitude scale by k m = 1000; therefore, we
LAB EXERCISE 3 FET Amplifier Design and Linear Analysis
ADS 2012 Workspaces and Simulation Tools (v.1 Oct 2012) LAB EXERCISE 3 FET Amplifier Design and Linear Analysis Topics: More schematic capture, DC and AC simulation, more on libraries and cells, using
Analog Circuits and Systems
Analog Circuits and Systems Prof. K Radhakrishna Rao Lecture 31: Waveform Generation 1 Review Phase Locked Loop (self tuned filter) 2 nd order High Q low-pass output phase compared with the input 90 phase
SPICE SIMULATION TUTORIAL
SPICE SIMULATION TUTORIAL DESIGN ENTRY TOOL------------------------------------------------------- This tutorial will show you how to open, modify and simulate a project using the Cadence simulation tool.
Operational Amplifiers
Operational Amplifiers Continuing the discussion of Op Amps, the next step is filters. There are many different types of filters, including low pass, high pass and band pass. We will discuss each of the
Class #16: Experiment Matlab and Data Analysis
Class #16: Experiment Matlab and Data Analysis Purpose: The objective of this experiment is to add to our Matlab skill set so that data can be easily plotted and analyzed with simple tools. Background:
Testing and Stabilizing Feedback Loops in Today s Power Supplies
Keywords Venable, frequency response analyzer, impedance, injection transformer, oscillator, feedback loop, Bode Plot, power supply design, open loop transfer function, voltage loop gain, error amplifier,
EE233 Autumn 2016 Electrical Engineering University of Washington. EE233 HW7 Solution. Nov. 16 th. Due Date: Nov. 23 rd
EE233 HW7 Solution Nov. 16 th Due Date: Nov. 23 rd 1. Use a 500nF capacitor to design a low pass passive filter with a cutoff frequency of 50 krad/s. (a) Specify the cutoff frequency in hertz. fc c 50000
Lab 4 Rev. 1 Open Lab Due COB Friday April 6, 2018
EE314 Systems Spring Semester 2018 College of Engineering Prof. C.R. Tolle South Dakota School of Mines & Technology Lab 4 Rev. 1 Open Lab Due COB Friday April 6, 2018 In this lab we will setup Matlab
LABORATORY #3 QUARTZ CRYSTAL OSCILLATOR DESIGN
LABORATORY #3 QUARTZ CRYSTAL OSCILLATOR DESIGN OBJECTIVES 1. To design and DC bias the JFET transistor oscillator for a 9.545 MHz sinusoidal signal. 2. To simulate JFET transistor oscillator using MicroCap
RLC Software User s Manual
RLC Software User s Manual Venable Instruments 4201 S. Congress, Suite 201 Austin, TX 78745 512-837-2888 www.venable.biz Introduction The RLC software allows you to measure the frequency response of RLC
Using an automated Excel spreadsheet to compensate a flyback converter operated in current-mode. Christophe Basso, David Sabatié
Using an automated Excel spreadsheet to compensate a flyback converter operated in current-mode Christophe Basso, David Sabatié ON Semiconductor download Go to ON Semiconductor site and enter flyback in
EE301 ELECTRONIC CIRCUITS CHAPTER 2 : OSCILLATORS. Lecturer : Engr. Muhammad Muizz Bin Mohd Nawawi
EE301 ELECTRONIC CIRCUITS CHAPTER 2 : OSCILLATORS Lecturer : Engr. Muhammad Muizz Bin Mohd Nawawi 2.1 INTRODUCTION An electronic circuit which is designed to generate a periodic waveform continuously at
Assignment 8 Analyzing Operational Amplifiers in MATLAB and PSpice
ECEL 301 ECE Laboratory I Dr. A. Fontecchio Assignment 8 Analyzing Operational Amplifiers in MATLAB and PSpice Goal Characterize critical parameters of the inverting or non-inverting opampbased amplifiers.
Lecture 16 Date: Frequency Response (Contd.)
Lecture 16 Date: 03.10.2017 Frequency Response (Contd.) Bode Plot (contd.) Bode Plot (contd.) Bode Plot (contd.) not every transfer function has all seven factors. To sketch the Bode plots for a generic
The Design of 2.4GHz Bipolar Oscillator by Using the Method of Negative Resistance Cheng Sin Hang Tony Sept. 14, 2001
The Design of 2.4GHz Bipolar Oscillator by Using the Method of Negative Resistance Cheng Sin Hang Tony Sept. 14, 2001 Introduction In this application note, the design on a 2.4GHz bipolar oscillator by
ECE4902 Lab 5 Simulation. Simulation. Export data for use in other software tools (e.g. MATLAB or excel) to compare measured data with simulation
ECE4902 Lab 5 Simulation Simulation Export data for use in other software tools (e.g. MATLAB or excel) to compare measured data with simulation Be sure to have your lab data available from Lab 5, Common