Z-Axis Power Delivery (ZAPD) Concept and Implementation

Size: px

Start display at page:

Download "Z-Axis Power Delivery (ZAPD) Concept and Implementation"

Silvester Dixon
6 years ago
Views:

1 Z-Axis Power Delivery (ZAPD) Concept and Implementation 1

2 The Slew Rate Wall < 20pH < 20pH Beyond 2005 di/dt = 1000 A/ns V droop = 75 mv 2004 di/dt =680 A/ns V droop = 100 mv 1500pH 500pH 2003 di/dt = 400 A/ns V droop = 110 mv MB VRM Edge Connect VRM OPVR ZAPD 2

3 Power Delivery Challenge Reduction of Path Impedance VRM VRM Connector Mother Board And Socket Interposer Substrate Die Substrate µp 60 A/us 100 A/us 1000 A/us 100 A/ns 3 rd Droop Controlled by VRM & MB filter caps (Bulk & HF) Capacitance Capacitance is is a a Band-Aid. Band-Aid. Inductance Inductance is is the the Key. Key. 2 nd Droop Controlled by interposer & pkg caps 1 st Droop Controlled by on-die & pkg caps Based on Intel ITS presentation 3

4 Distributed Power Architectures Motherboard Interconnect DC/DC Voltage Regulator (VRM) Die Die Substrate Interposer (socket substrate) Motherboard LSC DSC Low Voltage High Current Inductors Capacitors High Voltage Low Current Example 32-Bit Processor Power Distribution (60 (60 A/us A/us max max at at VRM) Power Conversion Needs to to Move Closer to to CPU CPU 4

5 Distributed Power Architectures Edge-Connect Processor Interconnect Die Die Substrate) Interposer (socket substrate) Power Connector Voltage Regulator Module (VRM) Motherboard & Socket Removed from Power Delivery Path Example 64-bit Power Distribution (100 (100 A/us A/us max max at at VRM) Need Modular Power Supply As As Close As As Possible 5

6 The Next Logical Step? On-Package-Voltage-Regulation (OPVR)? Advantages Power distribution performance Disadvantages Non-modularity (embedded w/ CPU) VR failures result in CPU failures Concept has been around for over 6 years and has yet to take hold due to above. Power Delivery As Close to CPU as possible Interposer Substrate Microprocessor FETs, Caps, etc. Non-Modular Power Delivery Provides Electrical Solution But But Burdens CPU CPU Cost Cost 6

7 Power Path Analysis A Comparison of VRD to ZVRM VR Down Power Path Via Power flow Thermal lid IDC cap on substrate CPU die C4 solder balls ZVRM Power Path Capacitor on VRM Connector Substrate Planes Substrate C L 7

8 Z-Axis Power Delivery Fully integrated solution includes: Thermal Power / Signal Delivery Power Delivery to top of processor (Active / Passive) Alignment Keying Retention Efficient use of z-axis space 8

9 KEY BENEFITS Signal Routing separated from Power Routing Motherboard real estate consolidation A Single integrated heat sink assembly for CPU & Z-Axis circuitry. Fast response & tighter voltage variance due to VR proximity (reduced power impedance delivery ) = Higher frequencies for CPU. Performance able to support well beyond VRM capability. Potentially reduced component count due to reduced power delivery impedance (e.g. fewer capacitors). Confirmed designs up to 140 Amps. 9

10 Thermal 10

11 Z-Axis Power Delivery Thermal Solution Heat Sink Assembly A single integrated heat sink assembly for CPU & Z-Axis circuitry. Z-axis components lie on periphery of heat sink base where thermal performance for CPU is inefficient. 100 Watt; degree C per Watt 11

12 CPU 1.3 C ZVRM Thermal Profile ZVRM FETs ZVRM FETs ZVRM ZVRM Uses Uses Edges Edges of of CPU CPU Heatsink Heatsink which which are are not not Effectively Effectively Used Used Today Today Low Lateral Heat Conduction

Thermal A single integrated heat sink assembly for CPU & VR.

clips Clip Force: Meets Atholon64 Thermal Design Guide Spec.

256 C/Watt CPU Power Target: 100 Watts Form factor changes have allowed sub 0.

13 Thermal A single integrated heat sink assembly for CPU & VR. Mechanical 76mm x 109 mm x 85mm (H x W x L) Weight: ~ 500 grams with fan and clips Clip Force: Meets Atholon64 Thermal Design Guide Spec. Fan: 70 mm; 5400 RPM Mechanical C/Watt CPU Power Target: 100 Watts Form factor changes have allowed sub 0.20 C/Watt Materials Base: Aluminum Heat Pipe: Copper Fins: Aluminum and Copper Processor Thermal Interface: Shin Etsu G751 Status Sample Shipping Drawings available 13

Thermal Path Analysis A Comparison of VRD to ZVRM ZVRM Thermal Resistance Diagram Fan T Air Heat Sink θ Heat Sink T Heat Sink TIM3 θ TIM3 T TIM3 θ TIM3 T TIM3 θ TIM2 T TIM2 ZVRM θ PCB T PCB θ PCB T

14 Thermal Path Analysis A Comparison of VRD to ZVRM ZVRM Thermal Resistance Diagram Fan T Air Heat Sink θ Heat Sink T Heat Sink TIM3 θ TIM3 T TIM3 θ TIM3 T TIM3 θ TIM2 T TIM2 ZVRM θ PCB T PCB θ PCB T PCB TIM2 Lid θ Lid T Lid TIM1 Processor Die θ TIM1 T TIM1 Socket ZVRM (5-10W) 80W ZVRM (5-10W) MB Die Thermal Thermal Impedance Impedance System System to to Air Air θ SA θ = SA (Τ (Τ die Τ die Τ amb )/ amb )/(P(P die + die + P ZVRM ) ZVRM ) 14

15 Thermal Test Results An 80% efficient ZVRM, full coverage TIM3, and 32.5mm lid increased the case temperature by 2.1 C and die temperature by 2.3 C at 99W. This temperature increase can be reduced, but not yet thoroughly evaluated. The 32.5mm small lid had a 0.7 C increase in case temperature and a 0.1 C decrease in die temperature compared to the 37.5mm large lid package. Since this test requires the use of two different thermal sources. The ZAPD power connectors had less than a 13 C temperature increase from no ZVRM DC load to an 80% efficient ZVRM at 99W (65A). The ZVRM FETs had less than a 44 C temperature rise from ambient at 99W and 80% efficiency. 15

16 Voltage Regulation 16

Performance able to support well beyond VRM capability.

17 Z-Axis Power Delivery with Voltage Regulation (Optional) ZVRM Fast response & tighter voltage variance due to VR proximity (reduced power impedance delivery ) = Higher frequencies for CPU. Performance able to support well beyond VRM capability. Potentially reduced component count due to reduced power delivery impedance (e.g. fewer capacitors). A multi-phase DC-DC converter using traditional buck topology & industry standardized components. Confirmed designs up to 140 Amps. 17

18 Substrates 18

19 Proposed Substrate Modifications for ZAPD Surface Pads Thermal Lid Substrate Underfill Silicon Die C4 Solder Balls TIM-1 Contact Pads 19

Calibrated etched resistor on a polyamide PWB powered by the ZVRM.

20 Thermal Load Board Emulates the CPU/substrate thermal load. Verifies the thermal simulation results and serves as a stand alone DC load Calibrated etched resistor on a polyamide PWB powered by the ZVRM. Produces and accurately measures 78 to 101 watts of uniformly distributed heat. TLB Top TLB Bottom 20

Silicon Thermal Test Die STTV Validate Package/Substrate w/ ZVRM Demonstrate thermal, electrical and mechanical performance of the package in the ZVRM configuration STTV including BUM substrate,

21 Silicon Thermal Test Die STTV Validate Package/Substrate w/ ZVRM Demonstrate thermal, electrical and mechanical performance of the package in the ZVRM configuration STTV including BUM substrate, modified lid and C4 thermal die array Test MoBo with socket Package Testing Accelerated life, Durability, Shock and Vibration, Thermal Shock, Power Cycling, Temperature-Humidity Cycling Characterization / Analysis / Reliability Assessment Can selectively heat 16 locations 4 x 4 Thermal Die Array for STTV Thermal Power Testing 21

CRTV Contact Resistance Test Vehicle Mechanical Substrate Dimension: 40mm x 40mm Lid

configuration Materials Top Pads: 30u Electroplated Au over 120 u Nickel Features and

64887-001) Mimics mechanical load of typical microprocessor.

22 CRTV Contact Resistance Test Vehicle Mechanical Substrate Dimension: 40mm x 40mm Lid Dimension: 32mm x 32mm Electrical 16 zone thermal element 4-point Contact Resistance Test configuration Materials Top Pads: 30u Electroplated Au over 120 u Nickel Features and Benefits Designed to test contact resistance of Power Interconnect ( Molex Series Number: ) Mimics mechanical load of typical microprocessor. Fabricated by NTK Fits into standard upga connectors CRTV Contact Resistance Test Vehicle Used to evaluate contact resistance changes in the system. 22

23 Interconnect 23

Z-Axis Power Delivery Interconnect Features and Benefits High Current / Low Inductance Design Integrated metal reinforced alignment feature Environmental testing in progress Designed to be

interconnect) Uses high-current interconnect to contact surface of CPU pkg to support growing DC current.

24 Z-Axis Power Delivery Interconnect Features and Benefits High Current / Low Inductance Design Integrated metal reinforced alignment feature Environmental testing in progress Designed to be incorporated in Z-axis Interconnect architecture Designed for SMT Lid and substrate alignment built in to connector Power to the Top of the Processor Separate voltage source (VR or passive interconnect) Uses high-current interconnect to contact surface of CPU pkg to support growing DC current. Low impedance power delivery path to the microprocessor to support growing dynamic AC current changes of CPU (2 nd order droop reduced). 68 ph (34 ph design available, 15 ph designs modeled) Originally designed for power, but could be used for signals Connector designed to compensate for Z-Axis tolerances. Mechanical Vertical Compliance: 0.7 mm Contact Force: ~90 grams avg. Durability: 25 Cycles Electrical (Quad-Array) Loop Inductance: 68 ph Total Current Target: 80 Amps Materials Terminal: Phosphor-Bronze Housing: LCP Contact Plating: 30 u Au over 50 u Nickel SMT Tail Plating: Tin-Lead Status Sample quantities available Drawings available 24

25 Phase II and Phase III Connectors Lower Inductance??? 140 Amps 200 Amp Modeled Lower Cost 80 Amps 25

26 Mechanical Simulation Material : Beryllium Copper C17460 HT Thickness = mm Interference Height : 0.71 mm Normal Force : 108 grams 26

Confirms modeling calculations from design phase Uses the S 21

27 Interconnect AC Inductance Test Design verification vehicle to determine inductance and AC resistance. Confirms modeling calculations from design phase Uses the S 21 measurement technique with a network analyzer. Substrate Side ZVRM Side Fixture Assembly 27

28 Connector Inductance Phase III Connector Phase II Connector Simulation 28

29 DC Contact Testing 29

30 Test Fixtures TOP BOARD BOTTOM BOARD CRTV 30

31 Test Groups A) EIA-364 TS Temp and Humidity : Test Group 2 Low Level Contact Resistance: EIA Durability (Preconditioning) EIA plug / unplug cycles Thermal Shock 10 Cycles: -55 C to +85 C: Mated Low Level Contact Resistance: EIA Cyclic Temperature and Humidity 25 C at 80% humidity to 65 C at 50% humidity Ramp: 0.5 hours Dwell: 1 hour Cycles: 24 Low Level Contact Resistance: EIA Durability (Reseating): 3 plug / unplug cycles Low Level Contact Resistance: EIA C) Shock Low Level Contact Resistance: EIA EIA B Shock Test o 50G o 11mS half-sine E) Contact Beam Force vs. Displacement B) EIA-364 TS Vibration :Test Group 3 Low Level Contact Resistance: EIA Durability (Preconditioning) EIA plug / unplug cycles Temperature Life: EIA : Mated 105 C / 240 hours Low Level Contact Resistance: EIA Vibration EIA , Test Condition 7 Low Level Contact Resistance: EIA Vibration Schedule: Hz. 3.1 G Random PSD 15 minutes per axis duration D) Retention Force: Measure static force of retention hardware (frame, heatsink and clips) using supplied fixture. 31

32 Contact Resistance Evaluation 32

33 Temp Rise Top Bottom Thermal Couple soldered to terminal base 33

34 Temperature Rise Chart VRM PCB Bank 4 POWERED: Bank 1 ELECTRICALLY ISOLATED: Banks 2, 3, and 4 A B Bank 1 TC-13 TC Bank 3 Tr6209 Temperature Rise Profile on P2P, Specimen #1 - Signals - Power Path Pins - Return Path Pins Thermal Couple Locations 30 Bank TC 13 Temperature > Ambient (C) WORST Case sample results Worst Case Location: Outer locations ~ 5º less No Heatsink / No Fan / Closed still air room TC 14 Load: 1 Oz. Copper across Bank 1 4 Banks x 35 Amps per Bank = 140 Amps Time (min) 34

35 System Level Power Path Modeling 35

36 System Level Analysis VRD : Voltage Regulator Down As seen in most desktop PCs today Voltage regulator is soldered on to the motherboard. VRM : Voltage Regulator Module As seen in many servers today Voltage regulator is added to system in the form of a module Typically, module is inserted into an edgecard connector ZAPD: Z-Axis Power Delivery How does Passive and Active ZAPD systems compare to VRD and VRM System level analysis of VRD, VRM, Passive ZAPD and ZVRM 36

37 VRM System 37

38 ZAPD System 38

39 Compare Results: Power Path Impedance 3 rd order droop - VR Cap 2 nd order droop - Inductance 1 st order droop - Substrate Caps 39

40 System Testing ZVRM Voltage droop 162.8mV 68mV VRD High Hump Running Stopclk & TZ Five parts tested, average magnitude of the Hump = 162.8mV Reference design High Hump Running Stopclk & TZ Five parts tested, average magnitude of the Hump = 68mV 130mV 60mV VRD Low Hump Running Stopclk & TZ Five parts tested, average magnitude of the Hump = 106.4mV from VID setpoint, 130mV from onset of transient Reference design Low Hump Running Stopclk & TZ Five parts tested, average magnitude of the Hump = 94.4mV from the VID setpoint, 60mV from onset of transient. 40

41 System Testing Overshoot Comparison Graph Spike Voltage Variance Overshoot ZVRM = 45% Improvement over VRD VRD Only Active ZAPD Only Passive ZAPD Hump Voltage Variance Overshoot ZVRM = 139% Improvement over VRD VRD Only Active ZAPD Only Passive ZAPD 41

KEY BENEFITS Signal Routing separated from Power Routing Motherboard real estate consolidation A Single integrated heat sink assembly for CPU & Z-Axis circuitry.

42 KEY BENEFITS Signal Routing separated from Power Routing Motherboard real estate consolidation A Single integrated heat sink assembly for CPU & Z-Axis circuitry. Fast response & tighter voltage variance due to VR proximity (reduced power impedance delivery ) = Higher frequencies for CPU. Performance able to support well beyond VRM capability. Potentially reduced component count due to reduced power delivery impedance (e.g. fewer capacitors). Confirmed designs up to 140 Amps. 42

PRODUCT SPECIFICATION

PRODUCT SPECIFICATION ipass TM 0.8 mm PITCH I/O CONNECTOR REVISION: ECR/ECN INFORMATION: EC No: UCP200-137 DATE: 200 / 02 / 08 TITLE: 1 of 14 TABLE OF CONTENTS 1.0 SCOPE 3 2.0 PRODUCT DESCRIPTION 3 2.1 PRODUCT NAME AND SERIES