Last Time Buy. Deadline for receipt of LAST TIME BUY orders: April 30, 2011

Size: px

Start display at page:

Download "Last Time Buy. Deadline for receipt of LAST TIME BUY orders: April 30, 2011"

Clinton Jenkins
6 years ago
Views:

1 Last Time Buy These parts are in production but have been determined to be LAST TIME BUY. This classification indicates that the product is obsolete and notice has been given. Sale of this device is currently restricted to existing customer applications. The device should not be purchased for new design applications because of obsolescence in the near future. Samples are no longer available. Date of status change: November 1, 1 Deadline for receipt of LAST TIME BUY orders: April 3, 11 Recommended Substitutions: For existing customer transition, and for new customers or new applications, contact Allegro Sales. NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.

2 + A557 Features and Benefits 3 ma output current per channel Independent overcurrent protection and thermal limiting for each driver Output voltage to 6 V Output SOA protection Fault-detection circuitry for open or shorted load Low quiescent current Sleep Mode Integral output flyback/clamp diodes TTL- and 5 V CMOS-compatible inputs Package: 16-pin SOICW with internally fused pins (LB) Description The A557 has been specifically designed to provide costeffective solutions to relay-driving applications with up to 3 ma drive current per channel. It may also be used for driving incandescent lamps in applications where turn-on time is not a concern. Each of the four outputs will sink 3 ma in the on state. The outputs have a minimum breakdown voltage of 6 V and a sustaining voltage of 4 V. A low-power Sleep Mode is activated with either ENABLE low or all inputs low. In this mode, the supply current drops to below 1 μa. Overcurrent protection for each channel has been designed into these devices and is activated at a nominal 5 ma. It protects each output from short circuits with supply voltages up to 3 V. When an output experiences a short circuit, the output current is limited at the 5 ma current clamp. In addition, foldback circuitry decreases the current limit if an excessive voltage is present across the output and assists in keeping the device within its SOA (safe operating area). An exclusive-or circuit compares the input and output state of each driver. If either a short or open load condition is detected, a single FAULT output is turned on (active low). Not to scale Continued on the next page Functional Block Diagram FAULT ENABLE SLEEP CONTROL COMMON CONTROL ONE OF FOUR DRIVERS 6 A K V CC.5 V IN N OUT N THERMAL LIMIT CURRENT LIMIT 3 A << N

3 Description (continued) Continuous or multiple overload conditions causing the channel temperature to reach approximately 165 C will result in an additional linear decrease in the output current of the affected driver. If the fault condition is corrected, the output stage will return to its normal saturated condition. The package offers fused leads for enhanced thermal dissipation. Package LB is a 16-lead power wide SOIC for surface-mount applications. It is lead (Pb) free, with 1% matte tin leadframe plating. Selection Guide Part Number Package Packing Ambient Temperature ( C) A557KLBTR-T 16-lead SOIC 1 pieces per reel 4 to 15

4 Absolute Maximum Ratings Characteristic Symbol Notes Rating Units Logic Supply Voltage V CC 7. V Input Voltage V I or V OE 7. V Output Voltage V O 6 V Overcurrent Protected Output Voltage V O(OCP) 3 V Output Current I O per driver, and T J limited if higher current is Outputs current-limited to approximately 5 ma attempted 5 ma FAULT Output Voltage V FLT 6 V Package Power Dissipation P D See graph Operating Ambient Temperature T A Range K 4 to 15 ºC Range E 4 to 85 ºC Range S to 85 ºC Maximum Junction Temperature T J (max) 15 ºC Storage Temperature T stg 55 to 15 ºC ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS 1 5 SUFFIX 'LB', R = 9 C/W JA TEMPERATURE IN C 3

6 ELECTRICAL CHARACTERISTICS over operating temperature range, V CC = 4.75 V to 5.5 V Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Output Leakage Current* I CEX V O = 6 V, V I =.8 V, V OE =. V 3 1 μa V O = 6 V, V I =. V, V OE =.8 V <1. 1 μa Output Sustaining Voltage V O(SUS) I O = 1 ma, V I = V OE =.8 V, V CC = Open 4 V Output Saturation Voltage V O(SAT) I O = 1 ma 65 mv I O = 3 ma 18 3 mv Over-Current Limit I OM 5 ms PulseTest, V O = 5. V 5 ma Input Voltage V IH IN n or ENABLE. V V IL IN n or ENABLE.8 V Input Current I IH IN n or ENABLE, V IH =. V 1 μa I IL IN n or ENABLE, V IL =.8 V -1 μa Fault Output Leakage Current I FLT V FLT = 6 V μa V FLT = 5 V <1.. μa Fault Output Current I FLT V FLT = 5 V, Driver Output Open, V I =.8 V, V OE =. V μa Fault Output Saturation Voltage V FLT(SAT) I FLT = 3 μa.1.4 V Clamp Diode Forward Voltage V F I F = 5 ma V I F = 75 ma V Clamp Diode Leakage Current I R V R = 6 V 5 μa Turn-On Delay t PHL I O = 3 ma, 5% V I to 5% V O.6 1 μs From Sleep, I O = 3 ma, 5% V I to 5% V O 3. μs I O = 3 ma, 5% V OE to 5% V O μs Turn-Off Delay t PLH I O = 3 ma, 5% V I to 5% V O. 1 μs I O = 3 ma, 5% V OE to 5% V O μs Total Supply Current I CC All Outputs Off.75.1 ma Any One Output On 1 ma Two Outputs On 18 3 ma Three Outputs On 4 4 ma All Outputs On 3 5 ma Thermal Limit T J 165 C Typical Data is at T A = +5 C and V CC = 5 V and is for design information only. Negative current is defined as coming out of (sourcing) the specified terminal. As used here, -1 is defined as greater than +1 (absolute magnitude convention) and the minimum is implicitly zero. * Measurement includes output fault-sensing pull-down current. 5

7 TYPICAL OPERATING CHARACTERISTICS 6 OUTPUT SATURATION VOLTAGE IN VOLTS.3..1 VCC = 5 V 1 TA = 15 C TA = 5 C TA = -4 C 3 4 OUTPUT CURRENT IN MILLIAMPERES Dwg. GP-64 OUTPUT CURRENT LIMIT IN MILLIAMPERES OUTPUT VOLTAGE IN VOLTS TA = +5 C VCC = 5 V 3 4 Dwg. GP-65 6 TURN-OFF DELAY IN MICROSECONDS 4 IN SWITCHING ENABLE SWITCHING TA = +5 C VCC = 5 V TURN-ON DELAY IN MICROSECONDS 3 1 IN SWITCHING (FROM SLEEP) TA = +5 C VCC = 5 V ENABLE SWITCHING IN SWITCHING (AWAKE) OUTPUT CURRENT IN MILLIAMPERES Dwg. GP OUTPUT CURRENT IN MILLIAMPERES Dwg. GP

8 CIRCUIT DESCRIPTION AND APPLICATION The A557 low-current quad power drivers provide protected output driver functions, combined with a fault diagnostic scheme, plus an automatic low-current Sleep-Mode function. These devices monitor their outputs for fault (open or shorted) conditions. For each channel the input and output levels are compared. If these are different from the expected levels then a fault condition is flagged by pulling the common FAULT output low. Status IN N ENABLE OUT N FAULT H H L H Normal Load L H H H X L H H Sleep Mode All L X H H Over-Current or H H R L Short to Supply Open Load or L H L L Short to Ground Thermal Fault H H H L R = Linear drive, current limited. The FAULT output is operational only if ENABLE is high. The output state is detected by monitoring the OUT n terminal using a comparator whose threshold is typically.5 V. In order to detect open-circuit outputs, a 3 μa current sink pulls the output below the comparator threshold. To ensure correct fault operation, a minimum load of approximately 1 ma is required. The fault function is disabled when in sleep mode, i.e., FAULT goes high and the 3 μa output sinks are turned off. The FAULT output is a switched current sink of typically 6 μa. Each channel consists of a TTL/CMOS-compatible logic input gated with a common ENABLE input. A logic high at the input will provide drive to turn on the output npn switch. Each output has a current-limit circuit that limits the output current by detecting the voltage drop across a low-value internal resistor in the emitter of the output switch. If this drop reaches a threshold, then the base drive to the output switch is reduced to maintain constant current in the output. To keep the device within its safe operating area (SOA) this output current limit is further reduced: if the power dissipation in the output device increases the local junction temperature above 165 C (nominal), so as to limit the power dissipation (and hence the local junction temperature). As each channel has its own thermal limit circuitry this provides some independence between the output channels, i.e., one channel can be operating in thermally reduced current limit, while the others can provide full drive capability. as a function of the output voltage. Full current limit of 5 ma (nominal) is available up to approximately V O = 8 V; above this the limit is reduced linearly to about 35 ma at V O = 3 V. This helps to improve SOA by immediately reducing the peak power pulse into a shorted load at high V O. A logic low at the ENABLE input causes all outputs to be switched off regardless of the state of the IN terminals. In addition, the device is put into a low quiescent current sleep mode, reducing I CC below 1 μa. If ENABLE is taken high and any of the inputs go high, the circuit will auto-wake-up. However, if the device is enabled, but all inputs stay low, then the circuit remains in sleep mode. All outputs have internal flyback diodes, with a common-cathode connection at the K terminal. Incandescent lamp driver High incandescent lamp turn-on (in-rush currents) can contribute to poor lamp reliability and destroy semiconductor lamp drivers. When an incandescent lamp is initially turned on, the cold filament is at minimum resistance and would normally allow a 1x to 1x in-rush current. Warming (parallel) or current-limiting (series) resistors protect both driver and lamp but use significant power either when the lamp is off or when the lamp is on, respectively. Lamps with steady-state current ratings up to 3 ma can be driven without the need for warming or current-limiting resistors, if lamp turn-on time is not a concern (1s of ms). With these drivers, during turn-on, the high in-rush current is sensed by the internal sense resistor, drive current to the output stage is reduced, and the output operates in a linear mode with the load current limited to approximately 5 ma. During lamp warmup, the filament resistance increases to its maximum value, the output driver goes into saturation and applies maximum rated voltage to the lamp. 7

9 CIRCUIT DESCRIPTION AND APPLICATION (continued) LAMP CURRENT NORMAL LAMP IN-RUSH CURRENT ITRIP TIME NOT TO SCALE THERMAL GRADIENT SENSING CURRENT LIMIT Dwg. WP-8 Inductive load driver Bifilar (unipolar) stepper motors (and other inductive loads) can be driven directly. The internal diodes prevent damage to the output transistors by suppressing the high-voltage spikes that occur when turning off an inductive load. For rapid current decay (fast turn-off speeds), the use of Zener diodes will raise the flyback voltage and improve performance. However, the peak voltage must not exceed the specified minimum sustaining voltage (V SUPPLY + V Z + V F < V O(SUS) ). Over-current conditions In the event of a shorted load, or stalled motor, the load current will attempt to increase. As described above, the drive current to the affected output stage is linearly reduced, causing the output to go linear (limiting the load current to about 5 ma). As the junction temperature of the output stage increases, the thermalshutdown circuit will shut off the affected output. If the fault condition is corrected, the output driver will return to its normal saturated condition. Fault diagnostics A pull-up resistor or current source is required on the FAULT output. This can be connected to whatever supply level the following circuitry requires (within the specification constraints). For a 5 V supply (i.e., Vcc) 15 kω or greater should be used. As the fault diagnostic function is to indicate when the output state is different from the input state for any channel, the FAULT output waveform will obviously produce a pulse waveform following the combined duty-cycle of all channels showing a fault condition. There are therefore two basic approaches to using the function in an application: As an interrupt in a controller-based system. If the system has a microcontroller then a FAULT low causes an interrupt, which then initiates a diagnostic sequence to find the culprit channel. This sequence usually consists of cycling through each channel one at a time, while monitoring the FAULT output. It is then easy to determine which channel has the faulty output and how it is failing (i.e., short to supply, open-circuit or short to ground). The system may then take whatever action is required, but could continue with operation of the remaining good channels while disabling signals to the faulty channel. As a simple common fault indication. If there is no controller in the system then the FAULT output can be set to give an indication (via a lamp or LED, etc.) of a fault condition which might be anywhere on the four channels. Because the FAULT output is dependent on the states of the input and output (four possibilities) but will only indicate on two of them, the duty cycle at the FAULT output will reflect the duty cycle at the faulty channel s input (or its inverse, depending upon fault type). In typical applications (5% duty cycles) a simple solution is to make the pull-up current on the FAULT output much less than the pull-down current (6 μa), and add a capacitor to give a time constant longer than the period of operation. For typical values, the device will produce a continuous dc output level. Component values will need to be adjusted to cope with different conditions. 8

10 CIRCUIT DESCRIPTION AND APPLICATION (continued) NOT TO SCALE IN FAULT (SHORTED LOAD) FAULT (OPEN LOAD) WITH OUTPUT CAPACITOR OUTPUT CURRENT SHORT CIRCUIT NORMAL LOAD CURRENT LIMIT (1 V SUPPLY) CURRENT LIMIT (4 V SUPPLY) Dwg. WP-35 TIME Dwg. WP-13-1 Under some conditions it is possible to get spurious glitches on the FAULT output at load turn-on and turn-off transitions: Light load turn-off. Under light loading conditions the turnoff delay (see characteristics above) of the output stage increases and may result in a spurious fault output of a few μs (the duration being proportional to the turn-off delay). As it is difficult to define this over all operating conditions, if a particular application would be sensitive to this type of glitch, then it is generally recommended to include a small (about.1 μf) smoothing/ storage capacitor at the FAULT output. Incandescent lamp turn-on. As described above, driving an incandescent filament results in the driver operating in current limit for a period after turn-on. During this period a fault condition will be indicated (over current). As discussed above this period can be 1s of ms. To avoid this indication, the capacitor on the FAULT output would need to be increased to provide an appropriate time constant. Alternatively, in a microcontrollerbased system, the code could be written to ignore the FAULT condition for an appropriate period after lamp turn on. Correct FAULT operation cannot be guaranteed with an unconnected output unused outputs should not be turned on, or unused outputs should be pulled high to >.5 V, and/or associated inputs tied low. Thermal considerations Device power dissipation can be calculated as: P D = (V O1 x I O1 x duty cycle 1 ) + + (V O4 x I O4 x duty cycle 4 ) + (V CC x I CC ) Note - I CC is also modulated by the duty cycle, but this is a reasonable approximation for most purposes. This can then be compared against the permitted package power dissipation, using: Permitted P D = (15 T A )/R JA where R JA is given as 9 C/W R JA is measured on typical two-sided PCB with minimal copper ground area. Additional information is available on the Allegro website. 9

11 LB Package, 16-pin SOIC with internally fused pins 4 and 5, and 1 and ±. 4 ± ±.1 1.3± A B PCB Layout Reference View 16X.1 C SEATING PLANE C SEATING PLANE GAUGE PLANE.41 ± MAX. ±.1 For Reference Only Pins 4 and 5, and 1 and 13 internally fused Dimensions in millimeters (reference JEDEC MS-13 AA) Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area B Reference pad layout (reference IPC SOIC17P13X65-16M) All pads a minimum of. mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances Copyright , The products described here are manufactured under one or more U.S. patents or U.S. patents pending. reserves the right to make, from time to time, such de par tures from the detail spec i fi ca tions as may be required to permit improvements in the per for mance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The in for ma tion in clud ed herein is believed to be ac cu rate and reliable. How ev er, assumes no responsibility for its use; nor for any in fringe ment of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: 1

Protected Quad Power Driver

Protected Quad Power Driver Features and Benefits 700 ma output current per channel Independent overcurrent protection for each driver Thermal protection for device and each driver Low output-saturation voltage Integral output flyback