HW#3 Solution. Dr. Parker. Fall 2014
|
|
- Lee Peters
- 6 years ago
- Views:
Transcription
1 HW#3 Solution Dr. Parker Fall 2014 Assume for the problems below that V dd = 1.8 V, V tp0 is -.7 V. and V tn0 is.7 V. V tpbodyeffect is -.9 V. and V tnbodyeffect is.9 V. lambda=100 nm. Assume ß n (k n )= W/L µ A(microamps)/V 2 and ß p (k p )= 51 W/L µ A/V 2 1. (10%) A PMOS transistor has Vs = 1.7 V, V d =.9 V. V gd = -.3 V. What region of operation is it in? Vgd= -.3; Vgd= Vg- Vd=> Vg = Vgd + Vd = -.3 V +.9 V=.6 V Vtpbodyeffect= -.9 V (there is body effect since the source is not tied to the lowest potential) Vds=.9-1.7= -.8 V Vgs=.6-1.7= -1.1 V Is the transistor ON? Vgs Vtpbodyffect? ? True, so transistor is ON Vds > Vgs-Vtp? -.8 > -1.1 (-.9)? -.8 > -.2? False, transistor is in SATURATION region 2. (10 %) An NMOS transistor has Vds = 1.2 V. V d = 1.3 V. Is the transistor in the saturation region of operation when Vgs =1.1 V? Vds =Vd-Vs 1.2 = 1.3 Vs Vs= =.1 V There is body effect since the source of the transistor is not connected to the lowest potential. Vgs Vtpbodyffect? 1.1.9? True, transistor is ON Vds> Vgs Vtnbodyeffect? 1.2 > ? 1.2 >.2? The transistor is in SATURATION region 3. a) (5 %) A PMOS transistor is used as a pass transistor (switch). The input voltage is Vin = 1.6 V. The gate voltage Vgs=-1 V. The voltage Vout =.7 V at time t = 0+. What is the final output voltage at t = infinity? The source is at the input, so if it is ON the it doesn t limit the output voltage. To verify if the transistor is ON, we test for Vgs Vtpbodyffect; Vgs = -1 V, Vtpbodyeffect = -.9V, so the the above inequality is true and therefore the transistor is ON. Therefore, the output at t=infinity is 1.6V.
2 b) (3%) Does the PMOS transistor have body effect when t approaches infinity? Yes, it does have body effect because the source terminal is different from the highest potential. c) (10%) Assume the transistor width is three times unit size and the length is twice minimum size. Compute the drain current flow I DS at t = 0+ and at t=infinity. At t=0+, Vds=.7-1.6= -.9 V Vgs= -1 V Vtpbodyeffect= -.9 V (the source is lower than the highest potential) Vgs Vtpbodyeffect? If this condition is true, the transistor is ON ? The condition is true, so the transistor is ON. Vds > Vgs-Vtpbodyeffect? -.9 > -1 (-.9)? -.9 > -1? False, so the transistor is in SATURATION region Idsp =.5*µp*Cox*W/L*(Vgs-Vtpbodyeffect)^2 =.5*(51x10^-6)((3*(4*lambda))/(2*(2*lambda))(-1- (-.9))^2 = ua (negative sign indicates the current flow direction) At t=infinity Vds= 0 V Vgs= -1 V Vtpbodyeffect= -.9 V Vgs Vtpbodyeffect? If this condition is true, the transistor is ON ? The condition is true, so the transistor is ON. Vds > Vgs-Vtpbodyeffect? If the condition is true the transistor is in linear region 0 > -1 (-.9)? 0 > -.1? True, so the transistor is in LINEAR region Idsp = µp*cox*w/l*vds*(vgs-vtpbodyeffect Vds/2) Idsp= 0 A
3 4. a) (7 %) Identify the sources and drains in a transmission gate at t=0+ when Vin =.6 V and Vout = 1.3 V. Vgn = 1.6 V, and Vgp =.2 V. b) (8 %) What regions are the two transistors in when t approaches infinity? your answers. Be sure to justify NMOS: We have body effect because the source terminal of the nmos is not connected to the lowest potential. First, let s investigate if the transistor is ON: Vgs= = 1 V Vgs Vtpbodyffect? 1V.9? True, so the transistor is ON Since the NMOS transistor is ON, and the source is not at the output, then the NMOS pass transistor can pass the input voltage and at t= infinity the output voltage is.6 V Vgs= 1 V Vds= =0 V Vds < Vgs-Vtnbodyeffect? If this condition is true, then the transistor is in linear region. 0 < 1 -.9? True, the NMOS transistor is in LINEAR region PMOS: Vgs = = -.4 V Vgs Vtpbodyeffect? -.4 V -.9 V? False, the PMOS transistor is in cut-off
4 5. a) (10%) In the circuit below, what are the voltages at node A and Out at t= =infinity? For the NMOS transistor, the drain is at node A and the source is at VIn. For the PMOS, the source is at node Out and the drain is at node A. If the NMOS transistor is ON, node A at t=infinity is equal to VIn. NMOS: Let s investigate if the transistor is ON: Vgs= = 1.3 V Vgs Vtpbodyffect? 1.3.9? True, so transistor is ON At t=infinity the voltage at node A is Vin, so node A is equal to.5 V PMOS: Node Out is the source terminal. We have body effect since the source at t=infinity the source is not the highest potential. For the transistor to be ON: Vgs Vtpbodyeffect From this above inequality we get that, Vg - Vs Vtpbodyeffect Vs Vg Vtpbodyeffect Vs 0 (-.9); Vs.9; therefore at =infinity the output voltage Out=.9 V b) (5%) If the input Vin cannot be transfered to the output, what would be the range of voltages that you could apply to the gate of the pmos transistor to transfer Vin. Assume you can use a negative power supply. Any voltage less than or equal to VIn Vtpbodyeffect, so Vg -.4 is good. The pmos transistor is ON when the source terminal is greater than the gate terminal by the threshold of the transistor; so as long as the gate voltage is low enough to satisfy this condition, the pmos transistor is able to transfer the voltage at node A.
5 6. (5%) What is the effective channel resistance of a PMOS transistor of 10 lambda width and minimum length? Assume Vgs=-1.7 V, Vds= -.5V, Vg=0. Let s first verify that the transistor is ON and in LINEAR region Vgs = -1.7 V Vgs = Vg Vs Vs = Vg Vgs = 1.7 V (we have body effect) Vgs Vtpbodyeffect? True, therefore the transistor is ON. Vds = -.5 V Vds> Vgs Vtpbodyeffect? -.5 > -1.7 (-.9)? -.5 > -.8? This is true, so the PMOS transistor is in LINEAR region. Rchp = 1/( ß p *W/L*(Vgs-Vtpbodyeffect)) Rchp = 1/(51X10^-6*((10*lambda)/(2*lambda))*(-1.7-(-.9)) Rchp = 4.9 KΩ 7. (5%) What type of parasitic transistors causes latchup? Briefly explain how latchup can occur. Parasitic bipolar transistors causes latchup. Latchup occurs when we have current flowing between Vdd and ground away from the transistor channels in a CMOS process 8. (5%) Assume a channel is formed between drain and source of an NMOS transistor, so that the transistor is in linear region. If we continuously increase slowly the drain voltage, what would happen to the channel eventually? Would the transistor still be in linear region? If we increase the drain of the transistor we pull electrons from the pool of the n+diffusion, reducing the depth of the channel at the drain side. At some point, when the drain is high enough to meet the condition Vds=Vgs-Vthreshold, the channel is said to be in pinched-off region (the border between linear and saturation). If we keep increasing Vd, the transistor will move to saturation region. 9. (5%) Why do we need to have some space between the p+ diffusions to the edge of the n-well? We need to have some space between the p+ diffusions to the edge of the n-well to avoid a short circuit with the p-substrate 10. (7%) What is electromigration? How can it be avoided? Electromigration is the process through which a metal can break resulting in an open circuit due to the increase of the current density. For example, if a particle falls into a metal, so that the metal width is reduced, this makes a narrow tunnel through which current can flow faster. As a result as the electrons are flowing they start picking up metal atoms and moving them until finally the metal breaks causing an open circuit. It can be avoided by design rules, the minimum width in for metal is 3*lambda
6 11. (5%) What is the minimum distance in micrometers allowed between two unconnected metal1 features to prevent design rule violations? 3*lambda=.3 micrometers
HW#3 Solution. Dr. Parker. Fall 2015
HW#3 Solution Dr. Parker Fall 2015 Assume for the problems below that V dd = 1.8 V, V tp0 is -.7 V. and V tn0 is.7 V. V tpbodyeffect is -.9 V. and V tnbodyeffect is.9 V. Assume ß n (k n )= 219.4 W/L µ
More informationHW#3 Solution. Dr. Parker. Spring 2014
HW#3 olution r. Parker pring 2014 Assume for the problems below that V dd = 1.8 V, V tp0 is -.7 V. and V tn0 is.7 V. V tpbodyeffect is -.9 V. and V tnbodyeffect is.9 V. Assume ß n (k n )= 219.4 W/L µ A(microamps)/V
More informationDIGITAL VLSI LAB ASSIGNMENT 1
DIGITAL VLSI LAB ASSIGNMENT 1 Problem 1: NMOS and PMOS plots using Cadence. In this exercise, you are required to generate both NMOS and PMOS I-V device characteristics (I/P and O/P) using Cadence (Use
More informationCMOS Transistor and Circuits. Jan 2015 CMOS Transistor 1
CMOS Transistor and Circuits Jan 2015 CMOS Transistor 1 Latchup in CMOS Circuits Jan 2015 CMOS Transistor 2 Parasitic bipolar transistors are formed by substrate and source / drain devices Latchup occurs
More informationSolution HW4 Dr. Parker EE477
Solution HW4 Dr. Parker EE477 Assume for the problems below that V dd = 1.8 v, V tp0 is -.7 v. and V tn0 is.7 V. V tpbodyeffect is -.9 v. and V tnbodyeffect is.9 V. Assume ß n (k n )= 219.4 W/L µ A(microamps)/V
More informationLearning Outcomes. Spiral 2-6. Current, Voltage, & Resistors DIODES
26.1 26.2 Learning Outcomes Spiral 26 Semiconductor Material MOS Theory I underst why a diode conducts current under forward bias but does not under reverse bias I underst the three modes of operation
More information8. Combinational MOS Logic Circuits
8. Combinational MOS Introduction Combinational logic circuits, or gates, witch perform Boolean operations on multiple input variables and determine the output as Boolean functions of the inputs, are the
More informationMetal Oxide Semiconductor Field-Effect Transistors (MOSFETs)
Metal Oxide Semiconductor Field-Effect Transistors (MOSFETs) Device Structure N-Channel MOSFET Providing electrons Pulling electrons (makes current flow) + + + Apply positive voltage to gate: Drives away
More informationECE520 VLSI Design. Lecture 5: Basic CMOS Inverter. Payman Zarkesh-Ha
ECE520 VLSI Design Lecture 5: Basic CMOS Inverter Payman Zarkesh-Ha Office: ECE Bldg. 230B Office hours: Wednesday 2:00-3:00PM or by appointment E-mail: pzarkesh@unm.edu Slide: 1 Review of Last Lecture
More informationENEE307 Lab 7 MOS Transistors 2: Small Signal Amplifiers and Digital Circuits
ENEE307 Lab 7 MOS Transistors 2: Small Signal Amplifiers and Digital Circuits In this lab, we will be looking at ac signals with MOSFET circuits and digital electronics. The experiments will be performed
More information3.CMOS Inverter-homework
3.CMOS Inverter-homework 1. for a CMOS inverter, when the pmos and nmos are long-channel devices,or when the supply voltage is low, velocity does not occur, under these circumstances,vm(vin=vout)=? 2.
More informationPower dissipation in CMOS
DC Current in For V IN < V TN, N O is cut off and I DD = 0. For V TN < V IN < V DD /2, N O is saturated. For V DD /2 < V IN < V DD +V TP, P O is saturated. For V IN > V DD + V TP, P O is cut off and I
More informationModule 4 : Propagation Delays in MOS Lecture 19 : Analyzing Delay for various Logic Circuits
Module 4 : Propagation Delays in MOS Lecture 19 : Analyzing Delay for various Logic Circuits Objectives In this lecture you will learn the following Ratioed Logic Pass Transistor Logic Dynamic Logic Circuits
More informationLecture 16. Complementary metal oxide semiconductor (CMOS) CMOS 1-1
Lecture 16 Complementary metal oxide semiconductor (CMOS) CMOS 1-1 Outline Complementary metal oxide semiconductor (CMOS) Inverting circuit Properties Operating points Propagation delay Power dissipation
More informationLecture 16: MOS Transistor models: Linear models, SPICE models. Context. In the last lecture, we discussed the MOS transistor, and
Lecture 16: MOS Transistor models: Linear models, SPICE models Context In the last lecture, we discussed the MOS transistor, and added a correction due to the changing depletion region, called the body
More informationMicroelectronics, BSc course
Microelectronics, BSc course MOS circuits: CMOS circuits, construction http://www.eet.bme.hu/~poppe/miel/en/14-cmos.pptx http://www.eet.bme.hu The abstraction level of our study: SYSTEM + MODULE GATE CIRCUIT
More information8. Characteristics of Field Effect Transistor (MOSFET)
1 8. Characteristics of Field Effect Transistor (MOSFET) 8.1. Objectives The purpose of this experiment is to measure input and output characteristics of n-channel and p- channel field effect transistors
More informationLecture 13 - Digital Circuits (II) MOS Inverter Circuits. October 25, 2005
6.12 - Microelectronic Devices and Circuits - Fall 25 Lecture 13-1 Lecture 13 - Digital Circuits (II) MOS Inverter Circuits October 25, 25 Contents: 1. NMOS inverter with resistor pull-up (cont.) 2. NMOS
More informationMOS TRANSISTOR THEORY
MOS TRANSISTOR THEORY Introduction A MOS transistor is a majority-carrier device, in which the current in a conducting channel between the source and the drain is modulated by a voltage applied to the
More informationDesign cycle for MEMS
Design cycle for MEMS Design cycle for ICs IC Process Selection nmos CMOS BiCMOS ECL for logic for I/O and driver circuit for critical high speed parts of the system The Real Estate of a Wafer MOS Transistor
More informationDepletion-mode operation ( 공핍형 ): Using an input gate voltage to effectively decrease the channel size of an FET
Ch. 13 MOSFET Metal-Oxide-Semiconductor Field-Effect Transistor : I D D-mode E-mode V g The gate oxide is made of dielectric SiO 2 with e = 3.9 Depletion-mode operation ( 공핍형 ): Using an input gate voltage
More informationLecture 4. MOS transistor theory
Lecture 4 MOS transistor theory 1.7 Introduction: A MOS transistor is a majority-carrier device, in which the current in a conducting channel between the source and the drain is modulated by a voltage
More informationShorthand Notation for NMOS and PMOS Transistors
Shorthand Notation for NMOS and PMOS Transistors Terminal Voltages Mode of operation depends on V g, V d, V s V gs = V g V s V gd = V g V d V ds = V d V s = V gs - V gd Source and drain are symmetric diffusion
More informationEE 330 Laboratory 7 MOSFET Device Experimental Characterization and Basic Applications Spring 2017
EE 330 Laboratory 7 MOSFET Device Experimental Characterization and Basic Applications Spring 2017 Objective: The objective of this laboratory experiment is to become more familiar with the operation of
More information! PN Junction. ! MOS Transistor Topology. ! Threshold. ! Operating Regions. " Resistive. " Saturation. " Subthreshold (next class)
ESE370: ircuit-level Modeling, Design, and Optimization for Digital Systems Today! PN Junction! MOS Transistor Topology! Threshold Lec 7: September 16, 2015 MOS Transistor Operating Regions Part 1! Operating
More informationMOS Field Effect Transistors
MOS Field Effect Transistors A gate contact gate interconnect n polysilicon gate source contacts W active area (thin oxide area) polysilicon gate contact metal interconnect drain contacts A bulk contact
More informationEE5320: Analog IC Design
EE5320: Analog IC Design Handout 3: MOSFETs Saurabh Saxena & Qadeer Khan Indian Institute of Technology Madras Copyright 2018 by EE6:Integrated Circuits & Systems roup @ IIT Madras Overview Transistors
More informationECE315 / ECE515 Lecture 8 Date:
ECE35 / ECE55 Lecture 8 Date: 05.09.06 CS Amplifier with Constant Current Source Current Steering Circuits CS Stage Followed by CG Stage Cascode as Current Source Cascode as Amplifier ECE35 / ECE55 CS
More informationEE311: Electrical Engineering Junior Lab, Fall 2006 Experiment 4: Basic MOSFET Characteristics and Analog Circuits
EE311: Electrical Engineering Junior Lab, Fall 2006 Experiment 4: Basic MOSFET Characteristics and Analog Circuits Objective This experiment is designed for students to get familiar with the basic properties
More informationBuilding Blocks of Integrated-Circuit Amplifiers
Building Blocks of ntegrated-circuit Amplifiers 1 The Basic Gain Cell CS and CE Amplifiers with Current Source Loads Current-source- or active-loaded CS amplifier Rin A o R A o g r r o g r 0 m o m o Current-source-
More informationBasic Fabrication Steps
Basic Fabrication Steps and Layout Somayyeh Koohi Department of Computer Engineering Adapted with modifications from lecture notes prepared by author Outline Fabrication steps Transistor structures Transistor
More informationSession 10: Solid State Physics MOSFET
Session 10: Solid State Physics MOSFET 1 Outline A B C D E F G H I J 2 MOSCap MOSFET Metal-Oxide-Semiconductor Field-Effect Transistor: Al (metal) SiO2 (oxide) High k ~0.1 ~5 A SiO2 A n+ n+ p-type Si (bulk)
More informationLecture Integrated circuits era
Lecture 1 1.1 Integrated circuits era Transistor was first invented by William.B.Shockley, Walter Brattain and John Bardeen of Bell laboratories. In 1961, first IC was introduced. Levels of Integration:-
More informationECE 546 Lecture 12 Integrated Circuits
ECE 546 Lecture 12 Integrated Circuits Spring 2018 Jose E. Schutt-Aine Electrical & Computer Engineering University of Illinois jesa@illinois.edu ECE 546 Jose Schutt Aine 1 Integrated Circuits IC Requirements
More informationStudy of Differential Amplifier using CMOS
Study of Differential Amplifier using CMOS Mr. Bhushan Bangadkar PG Scholar Mr. Amit Lamba Assistant Professor Mr. Vipin Bhure Assistant Professor Electronics and Communication Electronics and Communication
More informationTransistor was first invented by William.B.Shockley, Walter Brattain and John Bardeen of Bell Labratories. In 1961, first IC was introduced.
Unit 1 Basic MOS Technology Transistor was first invented by William.B.Shockley, Walter Brattain and John Bardeen of Bell Labratories. In 1961, first IC was introduced. Levels of Integration:- i) SSI:-
More informationPESIT Bangalore South Campus
INTERNAL ASSESSMENT TEST 2 Date : 19/09/2016 Max Marks: 40 Subject & Code : Analog and Digital Electronics (15CS32) Section: III A and B Name of faculty: Deepti.C Time : 8:30 am-10:00 am Note: Answer five
More informationd. Why do circuit designers like to use feedback when they make amplifiers? Give at least two reasons.
EECS105 Final 5/12/10 Name SID 1 /20 2 /30 3 /20 4 /20 5 /30 6 /40 7 /20 8 /20 Total 1. Give a short answer to each question a. Your friend from Stanford says that he has designed a three-stage high gain
More informationELEC 2210 EXPERIMENT 12 NMOS Logic
ELEC 2210 EXPERIMENT 12 NMOS Logic Objectives: The experiments in this laboratory exercise will provide an introduction to NMOS logic. You will use the Bit Bucket breadboarding system to build and test
More informationConduction Characteristics of MOS Transistors (for fixed Vds)! Topic 2. Basic MOS theory & SPICE simulation. MOS Transistor
Conduction Characteristics of MOS Transistors (for fixed Vds)! Topic 2 Basic MOS theory & SPICE simulation Peter Cheung Department of Electrical & Electronic Engineering Imperial College London (Weste&Harris,
More informationTopic 2. Basic MOS theory & SPICE simulation
Topic 2 Basic MOS theory & SPICE simulation Peter Cheung Department of Electrical & Electronic Engineering Imperial College London (Weste&Harris, Ch 2 & 5.1-5.3 Rabaey, Ch 3) URL: www.ee.ic.ac.uk/pcheung/
More informationConduction Characteristics of MOS Transistors (for fixed Vds) Topic 2. Basic MOS theory & SPICE simulation. MOS Transistor
Conduction Characteristics of MOS Transistors (for fixed Vds) Topic 2 Basic MOS theory & SPICE simulation Peter Cheung Department of Electrical & Electronic Engineering Imperial College London (Weste&Harris,
More informationEE105 Fall 2015 Microelectronic Devices and Circuits: MOSFET Prof. Ming C. Wu 511 Sutardja Dai Hall (SDH)
EE105 Fall 2015 Microelectronic Devices and Circuits: MOSFET Prof. Ming C. Wu wu@eecs.berkeley.edu 511 Sutardja Dai Hall (SDH) 7-1 Simplest Model of MOSFET (from EE16B) 7-2 CMOS Inverter 7-3 CMOS NAND
More informationHomework 2 Solutions. Perform.op analysis, the small-signal parameters of M1 and M2 are shown below.
Problem 1 Homework 2 Solutions 1) Circuit schematic Perform.op analysis, the small-signal parameters of M1 and M2 are shown below. Small-signal parameters of M1 gds = 9.723u gm = 234.5u region = 2 vds
More informationField Effect Transistors (FET s) University of Connecticut 136
Field Effect Transistors (FET s) University of Connecticut 136 Field Effect Transistors (FET s) FET s are classified three ways: by conduction type n-channel - conduction by electrons p-channel - conduction
More informationECE 5745 Complex Digital ASIC Design Topic 2: CMOS Devices
ECE 5745 Complex Digital ASIC Design Topic 2: CMOS Devices Christopher Batten School of Electrical and Computer Engineering Cornell University http://www.csl.cornell.edu/courses/ece5950 Simple Transistor
More informationproblem grade total
Fall 2005 6.012 Microelectronic Devices and Circuits Prof. J. A. del Alamo Name: Recitation: November 16, 2005 Quiz #2 problem grade 1 2 3 4 total General guidelines (please read carefully before starting):
More informationEECE 481. MOS Basics Lecture 2
EECE 481 MOS Basics Lecture 2 Reza Molavi Dept. of ECE University of British Columbia reza@ece.ubc.ca Slides Courtesy : Dr. Res Saleh (UBC), Dr. D. Sengupta (AMD), Dr. B. Razavi (UCLA) 1 PN Junction and
More informationImproved Inverter: Current-Source Pull-Up. MOS Inverter with Current-Source Pull-Up. What else could be connected between the drain and V DD?
Improved Inverter: Current-Source Pull-Up MOS Inverter with Current-Source Pull-Up What else could be connected between the drain and? Replace resistor with current source I SUP roc i D v IN v OUT Find
More informationEE 501 Lab 1 Exploring Transistor Characteristics
Objectives: Tasks: EE 501 Lab 1 Exploring Transistor Characteristics Lab report due on Sep 8th, 2011 1. Make sure you have your cadence 6 work properly 2. Familiar with characteristics of MOSFET such as
More informationToday's Goals. Finish MOS transistor Finish NMOS logic Start CMOS logic
Bi Today's Goals Finish MOS transistor Finish Start Bi MOS Capacitor Equations Threshold voltage Gate capacitance V T = ms Q i C i Q II C i Q d C i 2 F n-channel - - p-channel ± ± + + - - Contributions
More informationLecture # 16 Logic with a State Dependent Device. Logic Gates How are they built in practice?
EECS 42 Introduction to Digital Electronics Andrew R. Neureuther These viewgraphs will be handed out in class 1/21/ Lecture # 16 Logic with a State Dependent Device S&O pp. 9-9, 4-6 (read for graphs and
More informationBasic Circuits. Current Mirror, Gain stage, Source Follower, Cascode, Differential Pair,
Basic Circuits Current Mirror, Gain stage, Source Follower, Cascode, Differential Pair, CCS - Basic Circuits P. Fischer, ZITI, Uni Heidelberg, Seite 1 Reminder: Effect of Transistor Sizes Very crude classification:
More information4: Transistors Non idealities
4: Transistors Non idealities Inversion Major cause of non-idealities/complexities: Who controls channel (and how)? Large Body(Substrate) Source Voltage V G V SB - - - - - - - - n+ n+ - - - - - - - - -
More informationUNIT 3: FIELD EFFECT TRANSISTORS
FIELD EFFECT TRANSISTOR: UNIT 3: FIELD EFFECT TRANSISTORS The field effect transistor is a semiconductor device, which depends for its operation on the control of current by an electric field. There are
More informationIntroduction to the Long Channel MOSFET. Dr. Lynn Fuller
ROCHESTER INSTITUTE OF TECHNOLOGY MICROELECTRONIC ENGINEERING Introduction to the Long Channel MOSFET Dr. Lynn Fuller Webpage: http://people.rit.edu/lffeee Electrical and 82 Lomb Memorial Drive Rochester,
More informationElectronic Circuits for Mechatronics ELCT 609 Lecture 6: MOS-FET Transistor
Electronic Circuits for Mechatronics ELCT 609 Lecture 6: MOS-FET Transistor Assistant Professor Office: C3.315 E-mail: eman.azab@guc.edu.eg 1 Introduction Why we call it Transistor? The name came as an
More informationMicroelectronics Circuit Analysis and Design. MOS Capacitor Under Bias: Electric Field and Charge. Basic Structure of MOS Capacitor 9/25/2013
Microelectronics Circuit Analysis and Design Donald A. Neamen Chapter 3 The Field Effect Transistor In this chapter, we will: Study and understand the operation and characteristics of the various types
More information55:041 Electronic Circuits
55:041 Electronic Circuits Mosfet Review Sections of Chapter 3 &4 A. Kruger Mosfet Review, Page-1 Basic Structure of MOS Capacitor Sect. 3.1 Width 1 10-6 m or less Thickness 50 10-9 m or less ` MOS Metal-Oxide-Semiconductor
More informationLecture 4. The CMOS Inverter. DC Transfer Curve: Load line. DC Operation: Voltage Transfer Characteristic. Noise in Digital Integrated Circuits
Noise in Digital Integrated Circuits Lecture 4 The CMOS Inverter i(t) v(t) V DD Peter Cheung Department of Electrical & Electronic Engineering Imperial College London URL: www.ee.ic.ac.uk/pcheung/ E-mail:
More informationLecture 13 - Digital Circuits (II) MOS Inverter Circuits. March 22, 2001
6.12 - Microelectronic Devices and Circuits - Spring 21 Lecture 13-1 Lecture 13 - Digital Circuits (II) MOS Inverter Circuits March 22, 21 Contents: 1. NMOS inverter with resistor pull-up (cont.) 2. NMOS
More informationMechatronics and Measurement. Lecturer:Dung-An Wang Lecture 2
Mechatronics and Measurement Lecturer:Dung-An Wang Lecture 2 Lecture outline Reading:Ch3 of text Today s lecture Semiconductor 2 Diode 3 4 Zener diode Voltage-regulator diodes. This family of diodes exhibits
More informationThe George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB
The George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB Experiment # 11 MOSFET Amplifiers testing and designing Equipment:
More informationModule-3: Metal Oxide Semiconductor (MOS) & Emitter coupled logic (ECL) families
1 Module-3: Metal Oxide Semiconductor (MOS) & Emitter coupled logic (ECL) families 1. Introduction 2. Metal Oxide Semiconductor (MOS) logic 2.1. Enhancement and depletion mode 2.2. NMOS and PMOS inverter
More informationLecture 13. Biasing and Loading Single Stage FET Amplifiers. The Building Blocks of Analog Circuits - III
Lecture 3 Biasing and Loading Single Stage FET Amplifiers The Building Blocks of Analog Circuits III In this lecture you will learn: Current biasing of circuits Current sources and sinks for CS, CG, and
More informationMOSFET Terminals. The voltage applied to the GATE terminal determines whether current can flow between the SOURCE & DRAIN terminals.
MOSFET Terminals The voltage applied to the GATE terminal determines whether current can flow between the SOURCE & DRAIN terminals. For an n-channel MOSFET, the SOURCE is biased at a lower potential (often
More informationECE 2274 MOSFET Voltmeter. Richard Cooper
ECE 2274 MOSFET Voltmeter Richard Cooper Pre-Lab for MOSFET Voltmeter Voltmeter design: Build a MOSFET (2N7000) voltmeter in LTspice. The MOSFETs in the voltmeter act as switches. To turn on the MOSFET.
More informationLECTURE 19 DIFFERENTIAL AMPLIFIER
Lecture 19 Differential Amplifier (6/4/14) Page 191 LECTURE 19 DIFFERENTIAL AMPLIFIER LECTURE ORGANIZATION Outline Characterization of a differential amplifier Differential amplifier with a current mirror
More informationField-Effect Transistor (FET) is one of the two major transistors; FET derives its name from its working mechanism;
Chapter 3 Field-Effect Transistors (FETs) 3.1 Introduction Field-Effect Transistor (FET) is one of the two major transistors; FET derives its name from its working mechanism; The concept has been known
More informationPart II: The MOS Transistor Technology. J. SÉE 2004/2005
Part II: The MOS Transistor Technology J. SÉE johann.see@ief.u-psud.fr 2004/2005 Lecture plan Towards the nanotechnologies... data storage The data processing through the ages MOS transistor in logic-gates
More informationMEASUREMENT AND INSTRUMENTATION STUDY NOTES UNIT-I
MEASUREMENT AND INSTRUMENTATION STUDY NOTES The MOSFET The MOSFET Metal Oxide FET UNIT-I As well as the Junction Field Effect Transistor (JFET), there is another type of Field Effect Transistor available
More informationCMOS VLSI Design (A3425)
CMOS VLSI Design (A3425) Unit III Static Logic Gates Introduction A static logic gate is one that has a well defined output once the inputs are stabilized and the switching transients have decayed away.
More informationEE 230 Lab Lab 9. Prior to Lab
MOS transistor characteristics This week we look at some MOS transistor characteristics and circuits. Most of the measurements will be done with our usual lab equipment, but we will also use the parameter
More information1. The simple, one transistor current source
1. The simple, one transistor current source The test schematic (srs-simpla-mos.asc): 1. Design the NMOS source for a 40µA output current and the minimum allowed output voltage V omin =50mV. The design
More informationECE 3110: Engineering Electronics II Fall Final Exam. Dec. 16, 8:00-10:00am. Name: (78 points total)
Final Exam Dec. 16, 8:00-10:00am Name: (78 points total) Problem 1: Consider the emitter follower in Fig. 7, which is being used as an output stage. For Q 1, assume β = and initally assume that V BE =
More informationENEE 307 Laboratory#2 (n-mosfet, p-mosfet, and a single n-mosfet amplifier in the common source configuration)
Revised 2/16/2007 ENEE 307 Laboratory#2 (n-mosfet, p-mosfet, and a single n-mosfet amplifier in the common source configuration) *NOTE: The text mentioned below refers to the Sedra/Smith, 5th edition.
More informationLecture 190 CMOS Technology, Compatible Devices (10/28/01) Page 190-1
Lecture 190 CMOS Technology, Compatible Devices (10/28/01) Page 190-1 LECTURE 190 CMOS TECHNOLOGY-COMPATIBLE DEVICES (READING: Text-Sec. 2.9) INTRODUCTION Objective The objective of this presentation is
More information4.1 Device Structure and Physical Operation
10/12/2004 4_1 Device Structure and Physical Operation blank.doc 1/2 4.1 Device Structure and Physical Operation Reading Assignment: pp. 235-248 Chapter 4 covers Field Effect Transistors ( ) Specifically,
More informationMetal-Oxide-Silicon (MOS) devices PMOS. n-type
Metal-Oxide-Silicon (MOS devices Principle of MOS Field Effect Transistor transistor operation Metal (poly gate on oxide between source and drain Source and drain implants of opposite type to substrate.
More informationCS/ECE 5710/6710. Composite Layout
CS/ECE 5710/6710 Introduction to Layout Inverter Layout Example Layout Design Rules Composite Layout Drawing the mask layers that will be used by the fabrication folks to make the devices Very different
More informationThis Week s Subject. DRAM & Flexible RRAM. p-channel MOSFET (PMOS) CMOS: Complementary Metal Oxide Semiconductor
DRAM & Flexible RRAM This Week s Subject p-channel MOSFET (PMOS) CMOS: Complementary Metal Oxide Semiconductor CMOS Logic Inverter NAND gate NOR gate CMOS Integration & Layout GaAs MESFET (JFET) 1 Flexible
More informationLecture 34: Designing amplifiers, biasing, frequency response. Context
Lecture 34: Designing amplifiers, biasing, frequency response Prof J. S. Smith Context We will figure out more of the design parameters for the amplifier we looked at in the last lecture, and then we will
More informationUNIT-III GATE LEVEL DESIGN
UNIT-III GATE LEVEL DESIGN LOGIC GATES AND OTHER COMPLEX GATES: Invert(nmos, cmos, Bicmos) NAND Gate(nmos, cmos, Bicmos) NOR Gate(nmos, cmos, Bicmos) The module (integrated circuit) is implemented in terms
More informationShort Channel Bandgap Voltage Reference
Short Channel Bandgap Voltage Reference EE-584 Final Report Authors: Thymour Legba Yugu Yang Chris Magruder Steve Dominick Table of Contents Table of Figures... 3 Abstract... 4 Introduction... 5 Theory
More informationEEC 118 Lecture #11: CMOS Design Guidelines Alternative Static Logic Families
EEC 118 Lecture #11: CMOS Design Guidelines Alternative Static Logic Families Rajeevan Amirtharajah University of California, Davis Jeff Parkhurst Intel Corporation Announcements Homework 5 this week Lab
More informationField-Effect Transistors
Field-Effect Transistors The field-effect transistor 1 is a semiconductor device which depends for its operation on the control of current by an electric field. There are two types of field-effect transistors,
More informationEE 40. Midterm 3. November 14, 2002
Lab TA: Dan Bart Nir Konrad Yu Ching EE 40 Midterm 3 November 14, 2002 PLEASE WRITE YOUR NAME ON EACH ATTACHED PAGE PLEASE SHOW YOUR WORK TO RECEIVE PARTIAL CREDIT Problem 1: 10 Points Possible Problem
More informationCPE/EE 427, CPE 527 VLSI Design I CMOS Inverter. CMOS Inverter: A First Look
CPE/EE 427, CPE 527 VLSI Design I CMOS Inverter Department of Electrical and Computer Engineering University of Alabama in Huntsville Aleksandar Milenkovic CMOS Inverter: A First Look C L 9/11/26 VLSI
More informationDigital Integrated Circuits Designing Combinational Logic Circuits. Fuyuzhuo
Digital Integrated Circuits Designing Combinational Logic Circuits Fuyuzhuo Introduction Digital IC Ratioed Logic Introduction Digital IC EE141 2 Ratioed Logic design Basic concept Resistive load Depletion
More information3: MOS Transistors. Non idealities
3: MOS Transistors Non idealities Inversion Major cause of non-idealities/complexities: Who controls channel (and how)? Large Body(Substrate) Source Voltage V G V SB - - - - - - - - n+ n+ - - - - - - -
More informationLecture 14. FET Current and Voltage Sources and Current Mirrors. The Building Blocks of Analog Circuits - IV
Lecture 4 FET Current and oltage s and Current Mirrors The Building Blocks of Analog Circuits n this lecture you will learn: Current and voltage sources using FETs FET current mirrors Cascode current mirror
More informationEECS 141: SPRING 98 FINAL
University of California College of Engineering Department of Electrical Engineering and Computer Science J. M. Rabaey 511 Cory Hall TuTh3:3-5pm e141@eecs EECS 141: SPRING 98 FINAL For all problems, you
More informationIntelligent Systems Group Department of Electronics. An Evolvable, Field-Programmable Full Custom Analogue Transistor Array (FPTA)
Department of Electronics n Evolvable, Field-Programmable Full Custom nalogue Transistor rray (FPT) Outline What`s Behind nalog? Evolution Substrate custom made configurable transistor array (FPT) Ways
More informationWeek 7: Common-Collector Amplifier, MOS Field Effect Transistor
EE 2110A Electronic Circuits Week 7: Common-Collector Amplifier, MOS Field Effect Transistor ecture 07-1 Topics to coer Common-Collector Amplifier MOS Field Effect Transistor Physical Operation and I-V
More informationDigital Microelectronic Circuits ( ) Pass Transistor Logic. Lecture 9: Presented by: Adam Teman
Digital Microelectronic Circuits (361-1-3021 ) Presented by: Adam Teman Lecture 9: Pass Transistor Logic 1 Motivation In the previous lectures, we learned about Standard CMOS Digital Logic design. CMOS
More informationEECS 141: FALL 98 FINAL
University of California College of Engineering Department of Electrical Engineering and Computer Science J. M. Rabaey 511 Cory Hall TuTh9:30-11am ee141@eecs EECS 141: FALL 98 FINAL For all problems, you
More informationCOMPARISON OF THE MOSFET AND THE BJT:
COMPARISON OF THE MOSFET AND THE BJT: In this section we present a comparison of the characteristics of the two major electronic devices: the MOSFET and the BJT. To facilitate this comparison, typical
More informationAnalog IC: Project: 1.8 Volt Band Gap Reference: Due Date 11/09/2014
Analog IC: Project: 1.8 Volt Band Gap Reference: Due Date 11/09/2014 Frederick Rockenberger September 11, 2014 Project Specications bandgap reference maximum power consumption = 10 microwatt, supply voltage
More informationExam 1 ECE 410 Fall 2002
NAME: Exa 1 ECE 410 Fall 2002 During this exa you are allowed to use a calculator and the equations sheet provided. You are not allowed to speak to or exchange books, papers, calculators, etc. with other
More informationENG2410 Digital Design CMOS Technology. Fall 2017 S. Areibi School of Engineering University of Guelph
ENG2410 Digital Design CMOS Technology Fall 2017 S. reibi School of Engineering University of Guelph The Transistor Revolution First transistor Bell Labs, 1948 Bipolar logic 1960 s Intel 4004 processor
More information