TSB-67. Transmission Performance Specifications for Field Testing of UTP Cabling Systems

Size: px
Start display at page:

Download "TSB-67. Transmission Performance Specifications for Field Testing of UTP Cabling Systems"

Transcription

1 TSB-67 Transmission Performance Specifications for Field Testing of UTP Cabling Systems Prepared by: ANSI/EIA/TIA PN-3287 Task Group on UTP Link Performance

2 Required Field Test Parameters for TSB-67 Wire Map Length Propagation Delay Delay Skew Attenuation Near-End Crosstalk (NEXT)

3 The new category 5 wire map same length same attenuation same NEXT same propagation delay already spec d delay skew already spec d Power Sum NEXT new Return Loss new (already in ISO) ELFEXT new Power Sum ELFEXT new

4 Link Definition Channel (Two transitions at each end) Channel End USER S PATCH CORD WALL OUTLET USER S PATCH CORD Channel End HORIZONTAL CABLE PATCH PANEL WIRING CLOSET Under carpet or furniture connector WORK AREA

5 Link Definition Basic Link (One transition at each end) Link End Link End PATCH PANEL WALL OUTLET HORIZONTAL CABLE TESTER PATCH CORD TESTER PATCH CORD WORK AREA WIRING CLOSET

6 Horizontal Cabling Length Limits OVERALL LINK LENGTH LIMIT: 100 Meters Max HUB/SWITCH PATCH CORDS 7m Max* WORK AREA CORDS 3m Max WIRING CLOSET (TC) HORIZONTAL CABLE 90 Meters Max *Total combined length off all patch cords in TC cannot exceed 7m WORK AREA

7 AutoTest Results Autotest runs all tests required by the choosen standard TSB-67: Wire Map Length NEXT Attenuation

8 Wire Map Continuity end-to-end Shorts between any two or more conductors (or shield) Transposed pairs Reversed pairs Split pairs...and any other miswires

9 Correct Pair Wiring

10 Wire Map Results

11 Reversed Pair

12 Transposed Pairs Example: mix T568A and T568B wiring standards = Trouble

13 Pin/Pair Assignment - T568A Pair 2, (Orange) Pair 3, (Green) Pair 1, (Blue) Pair 4, (Brown)

14 Pin/Pair Assignment - T568B Pair 3, (Green) Pair 2, (Orange) Pair 1, (Blue) Pair 4, (Brown)

15 DSP Series Test Results Transposed Pair

16 Split Pairs Caused by connecting wires from different pairs to paired pins This effectively results in an untwisted cable which can cause a high level of Near-end Crosstalk (NEXT)

17 Split Pairs

18 DSP Series Test Results

19 Nominal Velocity of Propagation (NVP) The speed at which a signal travels in a cable, expressed as a percentage of the speed of light in vacuum. NVP = speed at which pulse travels in cable speed of light in vacuum X 100% Speed of light in vacuum is 300,000 km/s or 0.3 m/nsec

20 Length Calculation Length = RT_Prop_delay (nsec) x NVP x Speed_of_Light Example: measurement of Prop_delay: 435 nsec NVP (%) 2 Length (ft)

21 Length Results

22 Length Measurement Reporting Measured Link Length Calculated for shortest electrical delay Includes the length of the two patch cords Test Limit (PASS/FAIL) Maximum allowable link length PLUS 10% Calculated for shortest electrical delay

23 Propagation Delay ns 486 ns 494 ns 484 ns

24 Propagation Delay

25 Delay Skew The difference in propagation delay ns (481 ns) 5ns (486 ns) 13 ns (494 ns) 3ns (484 ns)

26 Delay Skew

27 DSP Series Test Results

28 Attenuation The amount of signal loss in the transmission link (expressed in db) Signal Source Signal Receiver db Loss

29 Sources/Causes Attenuation The electrical characteristics of the cable materials and its construction Insertion losses due to improper termination (IDC) Reflections due to impedance mismatches Effect Above a certain amount of loss, the cabling link may not reliably transmit network data

30 Attenuation as a Function of Frequency TEST CABLE (300 ft) 25 Attenuation (db) Pair 1,2 PASS: 30-May-97 01:20:22pm MHz Mukilteo Cable Co. TIA Cat 5 Basic Link Limit

31 Attenuation View Plot

32 DSP Series Test Results

33 Attenuation Measurement Reporting PASS Highest measured attenuation and frequency at which this occurred Test limit at this frequency FAIL Measured attenuation and frequency at which this occurred Test limit at this frequency

34 Near End Crosstalk (NEXT) Transmit Receive Crosstalk measures the amount of signal interference from one pair to another pair NEXT measures crosstalk at the signal source (Near End)

35 Effects of NEXT Similar to noise interference Induced signal may have sufficient amplitude to corrupt the original signal to be falsely detected as valid data Effect: intermittent station lockup complete network attachment failure

36 NEXT

37 NEXT Results

38 NEXT is measured in db NEAR END 1 Tx signal 2 3 Rx dist. 6 FAR END NEXT (db) = 10 Log Power of measured disturbance Power of transmitted signal

39 NEXT View Plot Press View Plot Press Next Pair to view other pair combina-tions Press EXIT until you return to the Autotest results screen

40 NEXT Measurement To be measured from both ends of the link

41 NEXT measurements taken at the far end Highlight Press ENTER Press View Plot

42 Why Do We Need Next Measurement at Both Ends? NEAR END FAR END Tx PAIR Rx PAIR BAD CONNECTOR Crosstalk of MHz

43 Testing from the Far End Reveals the Problem NEAR END FAR END Tx PAIR Rx PAIR BAD CONNECTOR Crosstalk of MHz

44 NEXT Measurement Evaluation Worst Case Margin: +4.8dB at 2.7MHz

45 NEXT - Worst Case Margin Margin: Difference between measured value and pass/fail (minimum performance) value Positive margin means NEXT Loss is better than minimum (Pass) Negative margin means NEXT Loss exceeds the minimum (Fail) Worst case: smallest margin the point closest to the standard s limit across all frequencies

46 (Pair-to-pair) NEXT B A D C 6 Combinations A B A C A D B C B D C D

47 NEXT Headroom Worst case NEXT across all 12 pair-topair NEXT tests 6 pair combinations from Main Unit 6 pair combinations from Remote Unit Headroom indicates the quality of the link Positive = PASS Bigger value is better

48 Calculating Headroom Headroom = worst Worst Case NEXT Margin Headroom = 6.5dB

49 The traditional two-pair system S/N = ACR Workstation Transmit (Output) Receive (Input) NEXT External noise Signal Signal LAN equipment Receive (Input) Transmit (Output)

50 ACR Attenuation to Crosstalk Ratio A variant of Signal to Noise Ratio The difference between NEXT (in db) and Attenuation (in db) The best performance indicator to determine useable bandwidth

51 Link Performance NEXT is used as indicator for quality of components and workmanship. ACR as an indicator of maximum usable bandwidth. 10 db: still usable signal power 0 db: noise power equals signal power you cannot rely on signal energy above the frequency at which the ACR = 0 db

52 TIA Limits: Attenuation, NEXT, ACR Limit in db Att (limit) NEXT (limit) ACR (limit) Frequency in MHz

53 Measured ACR Values ACR in db ACR (limit) ACR (DSP) Frequency in MHz

54 DSP Series ACR Test Results

55 Power Sum NEXT Workstation Outlet Horizontal Cabling Patch Panel Hub Power Sum NEXT is the combined NEXT on one wire pair from all other wire pairs

56 Power Sum NEXT The amount of crosstalk induced on a pair when signals are applied simultaneously to all other cable pairs A harder test to pass than NEXT uses TIA NEXT pair-to-pair limits Will be included in new standard It s a calculation, not measurement.

57 Power Sum NEXT PS NEXT Margin PSNEXT Plot

58 NEXT and FEXT Workstation Telecommunications Outlet Cabling Patch panel Hub NEXT FEXT FEXT is additive all crosstalk along the link adds to the FEXT disturbance observed at the receiver

59 Multiple pair -parallel transmission Far-End Crosstalk (FEXT) adds disturbance Workstation Transmit (Output) Transmit (Output) Signal 1 Signal 2 FEXT LAN Equipment Receive (Input) Receive Input Example: 1000BASE-T: 4 pairs are used.)

60 ELFEXT (Equal Level FEXT) Workstation Outlet Horizontal Cabling Patch panel Hub FEXT attenuation ELFEXT (signal difference in db) ELFEXT is the FEXT level relative to the attenuated signal (FEXT-Attenuation)

61 Power Sum ELFEXT Workstation Transmit (Output) Signal 1 FEXT LAN Equipment Receive (Input) Example: 1000BASE-T: 4 pairs are used.)

62 ELFEXT: A factor in S/N Ratio Measure Far End Crosstalk Loss ( analogous to measuring NEXT loss) Measure attenuation ELFEXT: Subtract attenuation from FEXT loss ELFEXT: another indication of S/N for LAN systems where two or more signals travel in the same direction (1000BASE-T).

63 PSNEXT and PSFEXT Multiple Disturber NEXT (MDNEXT): Power Sum addition of NEXT Losses Multiple Disturber FEXT (MDFEXT): Power Sum addition of FEXT Losses Of particular importance in 2 situations: Use of 25-pair cable Network applications that use parallel transmission over 2 or more wire pairs

64 Return Loss A measure of reflected signal power over the frequency range of interest Result of variations in Characteristic Impedance Structural variations due to the cable manufacturing process Connectors Installation

65 Effect of Return Loss Full Duplex LAN systems System A Transmit Output Receive Input Signal A to B Reflection Signal B to A Directional Coupler System B Receive Input Desired signal = attenuated signal from other end. Noise = reflected signal on same wire pair.

66 Noise contributors in S/N Ratio ACR is the traditional S/N indicator for 2-wire pair LAN systems ACR no longer will be the only measure ELFEXT loss is another S/N indicator when multiple signals are transmitted in parallel Return loss causes another S/N degradation when signals on a wire pair are transmitted in two directions at the same time (Full Duplex)

67 Combined Noise Disturbance Transmit Output Receive Input Receiver must detect attenuated signal Disturbance at receiver input: NEXT (3 other pairs) ELFEXT (3 other pairs) Return Loss

n Proper pin termination at each end n Continuity to the remote end n Shorts between any two or more conductors n Transposed pairs: n Crossed pairs.

n Proper pin termination at each end n Continuity to the remote end n Shorts between any two or more conductors n Transposed pairs: n Crossed pairs. INTRODUCTION Structured Cabling or data cabling (also known Local Area Network or LAN Cabling) is increasing in its deployment for business, commercial and residential use to carry signaling for networks

More information

Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail

Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail 1 Outline Henriecus Koeman Fluke Networks July 9, 2001 This rather technical discussion contains

More information

AMP NETCONNECT Category 6 System

AMP NETCONNECT Category 6 System AMP NETCONNECT Category 6 System 2 How Did We Get Here? Basic Cabling Structure Component Specifications Link/Channel Specifications Additional Structure Options EIA/TIA TSB36 EIA/TIA 568 TIA/EIA TSB40

More information

Cabling Ad Hoc Cat 5e Measurements

Cabling Ad Hoc Cat 5e Measurements Cabling Ad Hoc Cat 5e Measurements Larry Cohen Solarflare Communications 1 Overview Cabling Ad Hoc Test Plan Measurement One Cat 5e horizontal cable sample, four test channel configurations characterized

More information

XX.7 Link segment characteristics

XX.7 Link segment characteristics XX.7 Link segment characteristics 10GBASE-T is designed to operate over a 4-pair balanced cabling system. Each of the four pairs supports an effective data rate of 2500 Mbps in each direction simultaneously.

More information

DELTA Test Report. Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model. Performed for Sterling

DELTA Test Report. Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model. Performed for Sterling DELTA Test Report TEST Reg. no. 19 Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model Performed for Sterling DANAK-19/16909 Project no.: T213173-01 Page 1

More information

Cable Testing TELECOMMUNICATIONS AND NETWORKING

Cable Testing TELECOMMUNICATIONS AND NETWORKING Cable Testing TELECOMMUNICATIONS AND NETWORKING Analog Signals 2 Digital Signals Square waves, like sine waves, are periodic. However, square wave graphs do not continuously vary with time. The wave holds

More information

Media. Twisted pair db/km at 1MHz 2 km. Coaxial cable 7 db/km at 10 MHz 1 9 km. Optical fibre 0.2 db/km 100 km

Media. Twisted pair db/km at 1MHz 2 km. Coaxial cable 7 db/km at 10 MHz 1 9 km. Optical fibre 0.2 db/km 100 km Media Attenuation Repeater spacing Twisted pair 10-12 db/km at 1MHz 2 km Coaxial cable 7 db/km at 10 MHz 1 9 km Optical fibre 0.2 db/km 100 km conniq.com provides an excellent tutorial on physical media.

More information

Qualification testing of 100 ohm shielded channel, Class EA. Performed for Tyco Electronics Raychem N.V.

Qualification testing of 100 ohm shielded channel, Class EA. Performed for Tyco Electronics Raychem N.V. We help ideas meet the real world DELTA Test Report DANAK TEST Reg. no. 19 Qualification testing of 100 ohm shielded channel, Class EA Performed for Tyco Electronics Raychem N.V. DANAK-19J1636 Project

More information

Field Measurements of Return Loss

Field Measurements of Return Loss Field Measurements of Return Loss White Paper By Mark Johnston and Jim Tonti Microtest October 21, 1998 Page 1 12/15/99 Overview Return loss is an important new measurement used to qualify the performance

More information

Cable Analysis. Extracting Information from Measured Data. The Performance Leader in Hand-Held Network Tools. Fanny Mlinarsky.

Cable Analysis. Extracting Information from Measured Data. The Performance Leader in Hand-Held Network Tools. Fanny Mlinarsky. Cable Analysis Extracting Information from Measured Data Fanny Mlinarsky 2-Nov-98 The Performance Leader in Hand-Held Network Tools Introduction Every cable tells a story. Cable certification measurements

More information

- Characteristic impedance of cabling links is characterised by Return Loss

- Characteristic impedance of cabling links is characterised by Return Loss ISO/IEC 11801 ISO 11801 is the principle design standard for structured cabling systems for all countries of the world that do not have more specific standards, such as ISO 11801 (European Union), TIA

More information

Product Bulletin. Belden DataTwist 4800 Cables

Product Bulletin. Belden DataTwist 4800 Cables Product Bulletin PB 296 Belden DataTwist 4800 Cables DataTwist 4800 UTP Cables provide significant headroom and robust data transmission performance for today s most demanding applications. The cables

More information

ECE 528 Understanding Power Quality

ECE 528 Understanding Power Quality ECE 528 Understanding Power Quality http://www.ece.uidaho.edu/ee/power/ece528/ Paul Ortmann portmann@uidaho.edu 208-733-7972 (voice) Lecture 41 1 Today Wiring for communications Decibels Coupling Avoiding

More information

Test Report based on DIN EN ISO/IEC 17025: 2005

Test Report based on DIN EN ISO/IEC 17025: 2005 Test Report based on DIN EN ISO/IEC 1725: 25 GHMT Type Approval 2 Connector Permanent Link, Copper, Class EA according ISO/IEC 1181-1 Ed.1. Document-no: P582a-18-E This Test Report with the measurements

More information

Independent Testing - For End User Confidence

Independent Testing - For End User Confidence Independent Testing - For End User Confidence EVALUATION OF PERFORMANCE OF LEVEL IIIe FIELD TESTER FROM FLUKE NETWORKS, TYPE DTX-1800 CABLE ANALYZER, FOR 500 MHz PERMANENT LINK MEASUREMENTS Main Unit,

More information

Test Report based on DIN EN ISO/IEC 17025:2005

Test Report based on DIN EN ISO/IEC 17025:2005 Test Report based on DIN EN ISO/IEC 1725:25 GHMT Type Approval 2 Connector Permanent Link, Copper, Class E according ISO/IEC 1181-1 Ed.1. 217-11 Document-no: P4945b-18-E This Test Report with the measurements

More information

Test Report. Test Result: PASS

Test Report. Test Result: PASS Test Report Designation : C6 A TIA/EIA68B. UTP Length :. m Temp :. Deg C Specification : CAT6 A MHZ UTP Test Date/Time : 11--16 1:1 Sample-ID-No. : GGRQ4 Customer : Rertech Drum no. :. Cable type : CAT6A

More information

EFFECT OF SHIELDING ON CABLE RF INGRESS MEASUREMENTS LARRY COHEN

EFFECT OF SHIELDING ON CABLE RF INGRESS MEASUREMENTS LARRY COHEN EFFECT OF SHIELDING ON CABLE RF INGRESS MEASUREMENTS LARRY COHEN OVERVIEW Purpose: Examine the common-mode and differential RF ingress levels of 4-pair UTP, F/UTP, and F/FTP cables at an (RJ45) MDI port

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 61935-1 Edition 3.0 2009-07 Specification for the testing of balanced and coaxial information technology cabling Part 1: Installed balanced cabling as specified in ISO/IEC 11801

More information

Independent Testing - For End User Confidence

Independent Testing - For End User Confidence Independent Testing - For End User Confidence ELECTRICAL TRANSMISSION PERFORMANCE TESTING OF SCREENED CATEGORY 6 ISO/IEC, EN & TIA/EIA CONNECTING HARDWARE ACCORDING TO REQUIREMENTS OF 2ND EDITION ISO/IEC

More information

B. Division-16 Basic Materials and Methods section apply to work specified in this section.

B. Division-16 Basic Materials and Methods section apply to work specified in this section. Section 16745 PREMISE CABLING SYSTEMS PART ONE GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification

More information

Copper and Fiber Optic Cables

Copper and Fiber Optic Cables Copper and Fiber Optic Cables Pietro Nicoletti piero[at]studioreti.it Cables-Engl - 1 P. Nicoletti: see note pag. 2 Copyright note These slides are protected by copyright and international treaties. The

More information

AESA TECHNOLOGY OF LAN CABLE

AESA TECHNOLOGY OF LAN CABLE TECHNOLOGY OF LAN CABLE CONTENT CHAPTER INTRODUCTION CHAPTER LOCAL AREA NETWORK (LAN) CHAPTER STRUCTURED CABLING SYSTEM (SCS) CHAPTER OPTICAL FIBER CABLE CHAPTER STANDARD CHAPTER COPPER LAN CABLE DESIGN

More information

Test report number CRT-001b Project number CRT-001b

Test report number CRT-001b Project number CRT-001b 3933 US Route 11 Cortland, NY 13 Telephone: (7) 3-6711 Facsimile: (7) 8-39 www.intertek.com July 24, 215 Nexans Cabling Solutions Alsembergsesteenweg 2, b3 B-151 Buizingen BELGIUM Test report number 12193693CRT-1b

More information

10GBASE-T T Tutorial. SolarFlare Communications IEEE Kauai, Hawaii. November 11, 2002

10GBASE-T T Tutorial. SolarFlare Communications IEEE Kauai, Hawaii. November 11, 2002 10GBASE-T T Tutorial IEEE 802.3 Kauai, Hawaii November 11, 2002 Communications Communications 10GBASE-T IEEE Tutorial, 11/11/2002 1 Agenda Introduction, Cabling & Challenges - George Zimmerman, Ph.D. CEO

More information

High Data Rate Characterization Report

High Data Rate Characterization Report High Data Rate Characterization Report VPSTP-016-1000-01 Mated with: VRDPC-50-01-M-RA and VRDPC-50-01-M-RA Description: Plug Shielded Twisted Pair Cable Assembly, 0.8mm Pitch Samtec, Inc. 2005 All Rights

More information

Test Report based on DIN EN ISO/IEC 17025

Test Report based on DIN EN ISO/IEC 17025 Test Report based on DIN EN ISO/IEC 17025 GHMT PREMIUM Verification Program Recertification Connector, Copper, Category 6A ISO/IEC 11801 Ed.2.2 This Test Report with the measurements consists of 28 pages.

More information

1) The addition of TCL and ELTCTL requirements to Category 6

1) The addition of TCL and ELTCTL requirements to Category 6 Subject 444 TO: SUBJECT: 455 East Trimble Road San Jose, CA 95131 July 28, 2008 Subscribers to UL s Listing and Verification Services for Communications Cable (DUZX) Revised Test and Follow-Up Service

More information

DATA TRANSMISSION. ermtiong. ermtiong

DATA TRANSMISSION. ermtiong. ermtiong DATA TRANSMISSION Analog Transmission Analog signal transmitted without regard to content May be analog or digital data Attenuated over distance Use amplifiers to boost signal Also amplifies noise DATA

More information

LAN tester EASYLAN. Instruction manual

LAN tester EASYLAN. Instruction manual LAN tester EASYLAN Instruction manual LAN TESTER EASYLAN Specifications indicated in the present instruction manual may be changed without prior notice. 1. INTRODUCTION AND SAFETY PROVISIONS...7 1.1 INTRODUCTION...

More information

High Data Rate Characterization Report

High Data Rate Characterization Report High Data Rate Characterization Report ERDP-013-39.37-TTR-STL-1-D Mated with: ERF8-013-05.0-S-DV-DL-L and ERM8-013-05.0-S-DV-DS-L Description: Edge Rate Twin-Ax Cable Assembly, 0.8mm Pitch Samtec, Inc.

More information

NETWORK CONNECTIVITY SYSTEMS

NETWORK CONNECTIVITY SYSTEMS NETWORK CONNECTIVITY SYSTEMS Installation Cable KS-STP Category 7 Installation Cable Certificates 10GBaseT FTP Category 6 Installation Cable UTP Category 6 Installation Cable UTP Category 5E Installation

More information

Synergy RJ45 LCS 6 Category 6 data outlets

Synergy RJ45 LCS 6 Category 6 data outlets Legrand Electric Ltd. Arena Park - Dial Lane West Bromwich - West Midlands - B70 0EB- United Kingdom Technical enquiries : Tel. 0870 8 90 - Fax. 0870 8 9021 CONTENTS PAGE 7300 56 7300 57 1. Applications...

More information

TileCal Analogue Cable Measurement Report

TileCal Analogue Cable Measurement Report Weiming Qian w.qian@rl.ac.uk +44-1235-446128 Rutherford Appleton Laboratory, UK 25 August 2005 Contents Contents... 2 1 Scope... 3 2 Impedance measurements... 3 2.1 Test setup... 3 2.2 Differential mode

More information

Chapter 12: Transmission Lines. EET-223: RF Communication Circuits Walter Lara

Chapter 12: Transmission Lines. EET-223: RF Communication Circuits Walter Lara Chapter 12: Transmission Lines EET-223: RF Communication Circuits Walter Lara Introduction A transmission line can be defined as the conductive connections between system elements that carry signal power.

More information

Communications Integrators, Inc. June S. Wilson Street, Suite 105 Tempe, Arizona Toll Free (800) Web Site

Communications Integrators, Inc. June S. Wilson Street, Suite 105 Tempe, Arizona Toll Free (800) Web Site Communications Integrators, Inc. June 2008 2625 S. Wilson Street, Suite 105 Tempe, Arizona 85282 Toll Free (800) 679-9711 Web Site www.ciinet.com Product Guide Specification Specifier Notes: This product

More information

Physical Test Setup for Impulse Noise Testing

Physical Test Setup for Impulse Noise Testing Physical Test Setup for Impulse Noise Testing Larry Cohen Overview Purpose: Use measurement results for the EM coupling (Campbell) clamp to determine a stable physical test setup for impulse noise testing.

More information

High Data Rate Characterization Report

High Data Rate Characterization Report High Data Rate Characterization Report EQRF-020-1000-T-L-SMA-P-1 Mated with: QSE-xxx-01-x-D-A and SMA-J-P-x-ST-TH1 Description: Cable Assembly, High Speed Coax, 0.8 mm Pitch Samtec, Inc. 2005 All Rights

More information

Category 7 A /Class F A Products

Category 7 A /Class F A Products CATEGORY 7 A /CLASS F A PRODUCTS Category 7 A /Class F A Products Exceeding ISO/IEC category 7 A /class F A specifications, Siemonʼs fully shielded TERA endto-end cabling solution is the highest-performing,

More information

Call For Interest PoE- plus. Chris Di Minico MC Communications

Call For Interest PoE- plus. Chris Di Minico MC Communications Call For Interest PoE- plus Chris Di Minico MC Communications cdiminico@ieee.org 1 IEEE 802.3 CFI Powering Ethernet Devices Over Data Cabling IEEE 802.3af Web Cameras Ethernet Switch Data and Power Security

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 +1-603-862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu +1-603-862-0166

More information

Notice Notice Notice Notice Notice

Notice Notice Notice Notice Notice TITLE: PCI-SIG ENGINEERING CHANGE NOTICE OCuLink Cable Spec ECN DATE: March, 0 AFFECTED DOCUMENT: OCuLink.0 SPONSOR: Part I:. Summary o the Functional Changes Alex Haser (Molex), Jay Neer (Molex) The IL/

More information

Data and Computer Communications. Chapter 3 Data Transmission

Data and Computer Communications. Chapter 3 Data Transmission Data and Computer Communications Chapter 3 Data Transmission Data Transmission quality of the signal being transmitted The successful transmission of data depends on two factors: characteristics of the

More information

Application Note 5044

Application Note 5044 HBCU-5710R 1000BASE-T Small Form Pluggable Low Voltage (3.3V) Electrical Transceiver over Category 5 Unshielded Twisted Pair Cable Characterization Report Application Note 5044 Summary The Physical Medium

More information

Request Request Request Request Request Request Request

Request Request Request Request Request Request Request TITLE: DATE: March, 0 AFFECTED DOCUMENT: OCuLink.0 SPONSOR: Part I:. Summary o the Functional Changes PCI-SIG ENGINEERING CHANGE REQUEST OCuLink Cable Spec ECR Rev. Alex Haser (Molex), Jay Neer (Molex)

More information

SECTION BUILDING WIRE AND CABLE

SECTION BUILDING WIRE AND CABLE SECTION 260519 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Building wire and cable. 2. Wiring connectors and connections. B. RELATED SECTIONS 1. Section 26 05 53 Electrical Identification. 2. Section

More information

Channel Characteristics and Impairments

Channel Characteristics and Impairments ELEX 3525 : Data Communications 2013 Winter Session Channel Characteristics and Impairments is lecture describes some of the most common channel characteristics and impairments. A er this lecture you should

More information

IEEE Std 802.3ap (Amendment to IEEE Std )

IEEE Std 802.3ap (Amendment to IEEE Std ) IEEE Std 802.3ap.-2004 (Amendment to IEEE Std 802.3.-2002) IEEE Standards 802.3apTM IEEE Standard for Information technology. Telecommunications and information exchange between systems. Local and metropolitan

More information

High Data Rate Characterization Report

High Data Rate Characterization Report High Data Rate Characterization Report EQCD-020-39.37-STR-TTL-1 EQCD-020-39.37-STR-TEU-2 Mated with: QTE-020-01-X-D-A and QSE-020-01-X-D-A Description: 0.8mm High-Speed Coax Cable Assembly Samtec, Inc.

More information

Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada

Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada jo.walling@sympatico.ca 0. Summary Contrary to the simplified perception about alien crosstalk,

More information

ACR (Attenuation to Crosstalk Ratio) ACR-F. Alien Crosstalk. Attenuation (signal attenuation, conductor attenuation)

ACR (Attenuation to Crosstalk Ratio) ACR-F. Alien Crosstalk. Attenuation (signal attenuation, conductor attenuation) ACR (Attenuation to Crosstalk Ratio) The distance between the wanted signal and the interfering signal (ACR) is an important factor for the transmission quality. To ensure a faultless transmission, the

More information

A Few (Technical) Things You Need To Know About Using Ethernet Cable for Portable Audio

A Few (Technical) Things You Need To Know About Using Ethernet Cable for Portable Audio A Few (Technical) Things You Need To Know About Using Ethernet Cable for Portable Audio Rick Rodriguez June 1, 2013 Digital Audio Data Transmission over Twisted-Pair This paper was written to introduce

More information

Lecture 2 Physical Layer - Data Transmission

Lecture 2 Physical Layer - Data Transmission DATA AND COMPUTER COMMUNICATIONS Lecture 2 Physical Layer - Data Transmission Mei Yang Based on Lecture slides by William Stallings 1 DATA TRANSMISSION The successful transmission of data depends on two

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS IEC 61935.1:2006 IEC 61935-1:2005 AS/NZS IEC 61935.1:2006 Australian/New Zealand Standard Testing of balanced communication cabling in accordance with ISO/IEC 11801 Part 1: Installed cabling AS/NZS

More information

A Novel Simplified Four-Port Scattering Parameter Model for Design of Four-Pair Twisted-Pair Cabling Systems for Local Area Networks

A Novel Simplified Four-Port Scattering Parameter Model for Design of Four-Pair Twisted-Pair Cabling Systems for Local Area Networks IEEE TRANSACTIONS ON MICROWAVE THEORY AND TECHNIQUES, VOL. 48, NO. 5, MAY 2000 815 A Novel Simplified Four-Port Scattering Parameter Model for Design of Four-Pair Twisted-Pair Cabling Systems for Local

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD IEC 61935-1 Edition 4.0 2015-12 colour inside Specification for the testing of balanced and coaxial information technology cabling Part 1: Installed balanced cabling as specified

More information

High Speed Characterization Report

High Speed Characterization Report TCDL2-10-T-05.00-DP and TCDL2-10-T-10.00-DP Mated with: TMMH-110-04-X-DV and CLT-110-02-X-D Description: 2-mm Pitch Micro Flex Data Link Samtec, Inc. 2005 All Rights Reserved Table of Contents Introduction...1

More information

Data sheet MC GC1000 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft

Data sheet MC GC1000 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft Page 1/6 MC GC0 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft 18427034141 Illustrations Principle diagram Product specification 10 GBit installation cable, simplex installation cable Cat.7 AWG 23 S/FTP with wires

More information

Successful SATA 6 Gb/s Equipment Design and Development By Chris Cicchetti, Finisar 5/14/2009

Successful SATA 6 Gb/s Equipment Design and Development By Chris Cicchetti, Finisar 5/14/2009 Successful SATA 6 Gb/s Equipment Design and Development By Chris Cicchetti, Finisar 5/14/2009 Abstract: The new SATA Revision 3.0 enables 6 Gb/s link speeds between storage units, disk drives, optical

More information

Data sheet MC GC1200 pro22 Cat.7A S/FTP 2x4P LSHF-FR 1640 ft

Data sheet MC GC1200 pro22 Cat.7A S/FTP 2x4P LSHF-FR 1640 ft Page 1/7 Illustrations Principle diagram Product specification 10 GBit installation cable, duplex installation cable Cat.7A AWG 22 S/FTP with wires shielded in pairs 2x4 pairs (PiMF) pair shield: plastic

More information

Automatic measuring system for LAN cables AXT & Cat 8 HF only

Automatic measuring system for LAN cables AXT & Cat 8 HF only Picture for information only Automatic measuring system for LAN cables AXT & Cat 8 HF only The fastest measuring system on the market Checked against certified ISO 17025 standards High accuracy Easy to

More information

Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables

Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables Indicative picture Phoenix 1004 DT Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables Compliant to all major national standards for telephone,

More information

Data and Computer Communications Chapter 3 Data Transmission

Data and Computer Communications Chapter 3 Data Transmission Data and Computer Communications Chapter 3 Data Transmission Eighth Edition by William Stallings Transmission Terminology data transmission occurs between a transmitter & receiver via some medium guided

More information

EQCD High Speed Characterization Summary

EQCD High Speed Characterization Summary EQCD High Speed Characterization Summary PRODUCT DESCRIPTION: A length of coaxial ribbon cable is terminated to a transition PCB break-out region onto which respective connectors are soldered. Three such

More information

High Speed Characterization Report

High Speed Characterization Report PCRF-064-1000-SMA-P-1 Mated with: PCIE-XXX-02-X-D-TH and SMA-J-P-X-ST-TH1 Description: Cable Assembly, Low Loss Microwave Coax, PCI Express Breakout Samtec, Inc. 2005 All Rights Reserved Table of Contents

More information

Bill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables.

Bill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables. 098-219r2 Prepared by: Ed Armstrong Zane Daggett Bill Ham Martin Ogbuokiri Date: 07-24-98 Revised: 09-29-98 Revised again: 10-14-98 Revised again: 12-2-98 Revised again: 01-18-99 1. REQUIREMENTS FOR SPI-3

More information

CAT. 5e U/UTP 4x2x24AWG/1 CCA DOUBLE SHEATH

CAT. 5e U/UTP 4x2x24AWG/1 CCA DOUBLE SHEATH CAT. 5e U/UTP 4x2x24AWG/1 CCA DOUBLE SHEATH FIGURE CONSTRUCTION Inner conductor CCA Φ 0.50±0.01mm Insulation Solid HDPE Φ 0.90±0.05mm Color 1 Blue & White/ Blue 2 Orange & White/ Orange 3 Green & White/

More information

HDMI Compliance Test Report

HDMI Compliance Test Report HDMI Compliance Test Report Cable: WS356G40L2P5AC Active/Passive: Active Guage: 40AWG Length: 2.5M Connector Type: A-C Summary Pass/ Fail Comment Test 5-2 wire assignment Test 5-3 TMDS Data Eye Diagram

More information

Data sheet MC GC1200 pro22 Cat.7A S/FTP 4P LSHF-FR, class Dca s2 d2

Data sheet MC GC1200 pro22 Cat.7A S/FTP 4P LSHF-FR, class Dca s2 d2 Page 1/7 Illustrations Principle diagram See enlarged drawings at the end of document Product specification 10 GBit installation cable, simplex installation cable Cat.7A AWG 22 S/FTP with wires shielded

More information

UTP Copper. SFTP Copper. FUTP Copper. Composite. Special Applications Copper. Category 5e. Category 6 Category 5E Category 3. Category 7A Category 7

UTP Copper. SFTP Copper. FUTP Copper. Composite. Special Applications Copper. Category 5e. Category 6 Category 5E Category 3. Category 7A Category 7 05/2011 Table of Contents n Table of Contents 1 n Product Selection 2 n HCM Overview 4 n HCM Certified Cabling Systems 6 n UTP Copper 8 n SFTP Copper 32 n FUTP Copper 36 n Special Applications Copper 42

More information

Contents. Telecom Service Chae Y. Lee. Data Signal Transmission Transmission Impairments Channel Capacity

Contents. Telecom Service Chae Y. Lee. Data Signal Transmission Transmission Impairments Channel Capacity Data Transmission Contents Data Signal Transmission Transmission Impairments Channel Capacity 2 Data/Signal/Transmission Data: entities that convey meaning or information Signal: electric or electromagnetic

More information

TEST REPORT. DANAK Reg. no. 19. Electrical performance testing of: Connecting Hardware according to IEC

TEST REPORT. DANAK Reg. no. 19. Electrical performance testing of: Connecting Hardware according to IEC Page 1 of 12 2 Appendices TEST REPORT DANAK Reg. no. 19 DELTA Danish Electronics, Light & Acoustics Venlighedsvej 4 DK-2970 Hørsholm Denmark Tel. (+45) 45 86 77 22 Fax (+45) 45 86 58 98 www.delta.dk Electrical

More information

Part II Data Communications

Part II Data Communications Part II Data Communications Chapter 3 Data Transmission Concept & Terminology Signal : Time Domain & Frequency Domain Concepts Signal & Data Analog and Digital Data Transmission Transmission Impairments

More information

Engineering the Power Delivery Network

Engineering the Power Delivery Network C HAPTER 1 Engineering the Power Delivery Network 1.1 What Is the Power Delivery Network (PDN) and Why Should I Care? The power delivery network consists of all the interconnects in the power supply path

More information

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860)

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860) 3933 US Route 11 Cortland, NY 1345 Telephone: (67) 753-6711 Facsimile: (67) 758-3659 www.intertek.com December 16, 214 Test Report Number: 33592CRT-137 Project Number: 33592 Legrand North America Superior

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 +1-603-862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu +1-603-862-0166

More information

CAT 5e UTP Cable: NETSET BOX [305m], indoor

CAT 5e UTP Cable: NETSET BOX [305m], indoor Code: E08_05 CAT 5e UTP Cable: NETSET BOX [05m], indoor NETSET BOX UTP 5e Ethernet cable far exceeds the requirements for Category 5e twisted pair cables. View of the cable box - inside 05m of the cable.

More information

Transmission Impairments

Transmission Impairments 1/13 Transmission Impairments Surasak Sanguanpong nguan@ku.ac.th http://www.cpe.ku.ac.th/~nguan Last updated: 11 July 2000 Transmissions Impairments 1/13 Type of impairments 2/13 Attenuation Delay distortion

More information

CAT 6 Data Wiring System Connectors

CAT 6 Data Wiring System Connectors NEW CAT 6 Data Wiring System Connectors TM2 Series Features. High-Speed Data Transfer Conforms to the TIA/EIA-568B.2- data Wiring standard, thereby clears CAT 6 transfer performance requirements. As such,

More information

CABLE TESTER. Models CA7024, CA7026 & CA7028. Call toll free (800) or visit

CABLE TESTER. Models CA7024, CA7026 & CA7028. Call toll free (800) or visit CABLE TESTER Models CA7024, CA7026 & CA7028 Call toll free (800) 537-0351 or visit www.allspec.com Hand-held LAN Cable Mapping and Troubleshooting Tester (Model CA7028) Hand-held Alphanumeric TDR (Time

More information

Category 6 UTP EuroClass C ca Cables

Category 6 UTP EuroClass C ca Cables Category 6 UTP EuroClass C ca Cables Datasheet: GD103704v1 APPLICATION Brand-Rex Cat6Plus C6U cables exceed the Category 6 performance standards. They are rated to 250MHz and are suitable for use in all

More information

The Amphenol Alden Products Company Industrial Ethernet Family of Products

The Amphenol Alden Products Company Industrial Ethernet Family of Products The Amphenol Alden Products Company Industrial Ethernet Family of Products The AmphenolAlden Products Company Industrial Ethernet Family of Products Ethernet Migrates Out of the Office Environment to the

More information

Lecture 3: Data Transmission

Lecture 3: Data Transmission Lecture 3: Data Transmission 1 st semester 1439-2017 1 By: Elham Sunbu OUTLINE Data Transmission DATA RATE LIMITS Transmission Impairments Examples DATA TRANSMISSION The successful transmission of data

More information

Where Did My Signal Go?

Where Did My Signal Go? Where Did My Signal Go? A Discussion of Signal Loss Between the ATE and UUT Tushar Gohel Mil/Aero STG Teradyne, Inc. North Reading, MA, USA Tushar.gohel@teradyne.com Abstract Automatic Test Equipment (ATE)

More information

Modular Plug Connectors Compliant to Enhanced Category 5 Standards

Modular Plug Connectors Compliant to Enhanced Category 5 Standards Modular Plug Connectors Compliant to Enhanced Category 5 Standards TM2P Series (Shielded Type) TM22P-88P (Non-shielded Type) Features. Supports High-Speed LAN Transmission Conforms to requirements of TIA/EIA-568B

More information

The Future of Cabling -

The Future of Cabling - FIET 2011 Limited Standards Activities onvenor T215 WG1: IT abling Secretary T215 WG2 The Future of abling beyond ategory 7A and OM4 Member JT1 S25 WG3: Generic abling onvenor JT1 S25 WG3 ITG: abling Implementation

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 (603) 862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu 603.862.0166

More information

Methods for Testing Impulse Noise Tolerance

Methods for Testing Impulse Noise Tolerance Methods for Testing Impulse Noise Tolerance May,6,2015 Larry Cohen Overview Purpose: Describe some potential test methods for impulse noise tolerance What we will cover in this presentation: Discuss need

More information

ENY81 Coupling Network

ENY81 Coupling Network Version 01.00 ENY81 Coupling Network January 2008 For radio disturbance measurements on unshielded, symmetrical telecommunications ports Eight-wire network Radio disturbance measurements in line with CISPR

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 (603) 862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu 603.862.0166

More information

EC 554 Data Communications

EC 554 Data Communications EC 554 Data Communications Mohamed Khedr http://webmail. webmail.aast.edu/~khedraast.edu/~khedr Syllabus Tentatively Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 Week

More information

Data Communication. Chapter 3 Data Transmission

Data Communication. Chapter 3 Data Transmission Data Communication Chapter 3 Data Transmission ١ Terminology (1) Transmitter Receiver Medium Guided medium e.g. twisted pair, coaxial cable, optical fiber Unguided medium e.g. air, water, vacuum ٢ Terminology

More information

ISO/IEC JTC 1/SC 25/WG 3 N 755 Date: Replaces ISO/IEC JTC 1/SC 25/WG 3 N n/a

ISO/IEC JTC 1/SC 25/WG 3 N 755 Date: Replaces ISO/IEC JTC 1/SC 25/WG 3 N n/a ISO/IEC JTC 1/SC 25/WG 3 N 755 Date: 2005-05-18 Replaces ISO/IEC JTC 1/SC 25/WG 3 N n/a ISO/IEC JTC 1/SC 25/WG 3 Customer Premises Cabling Secretariat: Germany (DIN) DOC TYPE: Liaison document TITLE: Letter

More information

L(f) = = (f) G(f) L2(f) Transmission Impairments: Attenuation (cont.)

L(f) = = (f) G(f) L2(f) Transmission Impairments: Attenuation (cont.) Transmission Impairments: Attenuation (cont.) how many times the put signal has attenuated relative to the input signal should be in L(f) (f) (f) A A in (f) (f) how many times the put signal has been amplified

More information

AM BASIC ELECTRONICS TRANSMISSION LINES JANUARY 2012 DEPARTMENT OF THE ARMY MILITARY AUXILIARY RADIO SYSTEM FORT HUACHUCA ARIZONA

AM BASIC ELECTRONICS TRANSMISSION LINES JANUARY 2012 DEPARTMENT OF THE ARMY MILITARY AUXILIARY RADIO SYSTEM FORT HUACHUCA ARIZONA AM 5-306 BASIC ELECTRONICS TRANSMISSION LINES JANUARY 2012 DISTRIBUTION RESTRICTION: Approved for Pubic Release. Distribution is unlimited. DEPARTMENT OF THE ARMY MILITARY AUXILIARY RADIO SYSTEM FORT HUACHUCA

More information

Single Fiber, Single wavelength, GbE / FE transceiver ODN requirements & performance measurements ODN = Optical Distribution Network

Single Fiber, Single wavelength, GbE / FE transceiver ODN requirements & performance measurements ODN = Optical Distribution Network Single, Single wavelength, GbE / FE transceiver ODN requirements & performance measurements ODN = Optical Distribution Network Meir Bartur, Zonu, Inc. IEEE 802.3 ah interim May 2002 1 Dependence on cable

More information

SIGNAL INTEGRITY ANALYSIS AND MODELING

SIGNAL INTEGRITY ANALYSIS AND MODELING 1.00mm Pitch BGA Socket Adapter System SIGNAL INTEGRITY ANALYSIS AND MODELING Rev. 2 www.advanced.com Signal Integrity Data Reporting At Advanced Interconnections Corporation, our Signal Integrity reporting

More information

Design Considerations for High-Speed RS-485 Data Links

Design Considerations for High-Speed RS-485 Data Links Design Considerations for High-Speed RS-485 Data Links Introduction The trend in high-speed data networks continues to push for higher data rates over longer transmission distances, and under ever-harsher

More information

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860)

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860) 3933 US Route 11 Cortland, NY 1345 Telephone: (67) 753-6711 Facsimile: (67) 758-3659 www.intertek.com December 16, 214 Test Report Number: 33592CRT-136 Project Number: 33592 Legrand North America Superior

More information