Micromachining with tailored Nanosecond Pulses

Size: px
Start display at page:

Download "Micromachining with tailored Nanosecond Pulses"

Transcription

1 Micromachining with tailored Nanosecond Pulses Hans Herfurth a, Rahul Patwa a, Tim Lauterborn a, Stefan Heinemann a, Henrikki Pantsar b a )Fraunhofer USA, Center for Laser Technology (CLT), Port Street, Plymouth, MI b ) VTT, Technical Research Center of Finland. ABSTRACT Fiber lasers in MOPA configuration are a very flexible tool for micromachining applications since they allow to independently adjust the pulse parameters such as pulse duration, repetition rates and pulse energy while maintaining a constant beam quality. The developed fiber laser provides an average power of 11 W and maximum pulse energy of 0.5 mj for a wide range of pulse parameters at diffraction limited beam quality. Its pulse duration and repetition rate are continuously adjustable from 10 ns to cw and from 10kHz to 1MHz respectively. Ablation experiments were carried out on stainless steel, nickel and silicon with the goal of optimizing removal rates or surface finish using nanosecond pulses of different parameters. Maximum removal rates are achieved on all three materials using relatively similar pulse parameters. For silicon, pulse duration of 320ns at 100kHz and 45mJ resulted in optimum removal. In single shot experiments on silicon a significant influence of the pulse duration was found with a distinct optimum for removal rate and surface finish. The optimum intensity at the work piece is in the range of 35MW/cm 2 to 70MW/cm 2. Lower values are below the ablation threshold, while the plasma shielding effect limits considerable increases in removal rates for intensities exceeding 70MW/cm 2. Keywords: Fiber laser, flexible pulse parameter, ablation, metal, silicon, 1. INTRODUCTION Pulsed lasers find more and more applications in the industry as the equipment cost continue to decrease and at the same time new products are launched to the market. New fiber lasers offer a cost effective solution to many applications but often the parameter range of these lasers is limited. Fraunhofer CLT has developed a new flexible pulsed fiber laser which can be operated using a very wide parameter window. The purpose of the study was to establish optimal parameters for processing different engineering materials and to establish the effect of pulse duration on the quality and efficiency of different laser processes. The results showed that optimal parameter ranges could be determined for all tested materials. It was found that especially the pulse energy and the pulse width have a great effect on the processing results. Reasons for this behavior are discussed. 2. XPRIMNTAL ST-UP 2.1 Pulsed fiber laser The pulsed fiber laser is a joint development of Fraunhofer USA, Center for Laser Technology (CLT) and the University of Michigan (UoM), College of ngineering. While the University of Michigan develops advanced fiber designs and testing, the laser system was engineered by Fraunhofer CLT. The system is based on the Master Oscillator Power Amplifier (MOPA) approach consisting of a master oscillator (seeder) and three amplifier stages. The principle set-up is shown in Figure1. The pre-amplifier is based on standard single mode fiber components, as they are used in the telecommunications industry. The power amplifier is currently based on standard large mode area fiber (30 µm core, 250 µm cladding). The unique feature of the fiber based MOPA system is the continuously adjustable pulse duration, repetition rate and pulse energy at constant beam quality, even at tens of watts average power. The system has a proven high pulse to pulse stability. A novel fiber concept for obtaining single mode radiation out of a large core fiber even without coiling or taper is currently under development. The performance of this new, patented fiber has been demonstrated for passive fibers and will be extended to active fibers in the near future. This development will enable scaling of the pulse energy in the multi milli-joule range. Photonics North 2007, edited by John Armitage, Proc. of SPI Vol. 6796, 67961G, (2007) X/07/$18 doi: / Proc. of SPI Vol G-1

2 Amplification Amp. factor Pump power Pulse energy Average power Peak power 33 db W 4.0µJ 0.18W 400W Amplification Amp. factor Pump power Pulse energy Average power Peak power 22 db W 0.5mJ 15W 50kW Signal diode Isolator First stage Second stage Third stage 14 SMSC db SMSC 19 db LMA 23 db 30/250 Isolator Isolator, Pump Pump taper Pump diode diode diode Output 300mW 500mW 30W Seeder Pre-amplifiers Power Amplifier Fig. 1. Principle MOPA set-up with seeder, two pre-amplifiers and power amplifier. The current Yb-based system is shown in Figure 2. It comprises the pump module for the power amplifier (bottom), the MOPA based fiber laser (middle) including all associated electronics and controls, as well as all optical components of the power amplifier with free space beam delivery and the pulse generator (top). C IDI IDI Specifications: Wavelength: /-4nm Beam quality: M 2 <1.5 Average power: 15W Pulse energy: 0.5mJ Pulse Length: 10ns to 1µs continuously adjustable Repetition Rate: 10kHz-1MHz continuously adjustable Fig. 2. Pulsed fiber laser system and specifications Pulse generator, MOPA system, and pump module for power amplifier (top to bottom) The main controller controls and monitors all pre-amplification components. It can be connected to a computer via thernet, RS-232 or RS-485. Basic control commands are used to change parameters and read the status of the connected devices. An analog interface is integrated to change parameter settings on a microsecond timescale, such as gating and pulse parameter variation. A fully integrated external frequency/pulse generator (Avtech) is used for the Proc. of SPI Vol G-2

3 seeder to allow continuous adjustability of pulse duration, duty cycle and amplitude. It is controlled via a RS-232 interface and provides an analog interface for gating and modulation of the amplitude. The performance of the system is shown in Figure 3 for pulse duration of 10ns and various repetition rates. 100,000 10,000 Pulse length: 10ns 10kHz Peak power [W] 1, kHz 1MHz nergy [µj] 1 CW Seed First stage Second stage Third stage Amplifier Stage Fig. 3. Peak power and pulse energy of pulsed fiber laser for individual stages 2.2 Processing optics and sample manipulation The collimated laser beam has a diameter of approximately 1mm at the laser output. A 5x telescope is used to increase the beam size before it enters the galvanometric scanner (Scanlab). Two different lenses with a focal length of 100mm and 160mm are used to focus and direct the beam onto the work piece. They result in spot minimum spot size of xx and xx respectively. While the beam is manipulated by the scanner in x- and y-direction during processing, the material samples are positioned in x-, y-, and z-direction with a high precision motion system (Aerotech). The motion system also repositions the samples in z-direction after the processing for each layer is completed. 3. RSULTS 3.1 Processing of Stainless Steel The objective for the experiments performed on stainless steel SS304 was to establish the relationship between processing parameters and the material removal rate. This was carried out by engraving 1.8mm x 1.8mm squares into the surface of a stainless steel plate of 2mm thickness. The engraving was done by scanning multiple layers, each of which ablated a thin layer of material from the surface. The total energy applied per square was kept constant at 121.5J. Therefore, for higher scanning velocity, the number of layers was increased respectively and for higher power, the number of layers was decreased to maintain the constant input energy per square. The scanning speed was varied from 100 to 800mm/s, the frequency from 20 to 100kHz and pulse width from 20 to 640ns. Two power levels were tested. With 163mm focal length, which creates an approximately 45µm focal spot diameter on the surface, 4.5W laser power was used. With the shorter focal length of 80mm, delivering an approximate focal spot diameter of 25µm, 2.25W of laser power on work piece surface was used. The displacement between hatched lines was in both cases 12µm and the area was scanned in the x- and y-direction. The material removal rate was determined by measuring the depth of the squares, and consequently the volume of the removed material. The depth was measured using an optical microscope and measuring the surface of the material, the distance to the highest peaks of the square and the lowest valleys. This did not in detail provide the correct amount of removed material, but gave a good estimate. The accuracy of measurement was the poorest with samples processed with a high scanning velocity and a low pulse repetition rate. For such conditions there was very little overlap of pulses and the engraved surface was very coarse. In these cases, the roughness (Rz) value of the surface is in the range of tens of micrometers. As a result, the volume measurement is not accurate. Figure 4 describes the measurement procedure. Proc. of SPI Vol G-3

4 Too surface Highest measur, point measurement Do' Fig. 4. Procedure to determine ablated material volume Using 2.25W of power and a spot size of 25µm (80mm focal length), the highest material removal efficiency [mm 3 /kj] is obtained at low repetition rates and pulse widths ranging form 80 to 320ns. In this parameter range, high peak power is achieved that leads to high material removal rates. The optimal material removal efficiency depends mainly on correlation between pulse width and frequency. At 100kHz highest material removal is obtained using an 80ns pulse width, which resulted in a 280W peak power and an average power density in the laser spot of 57.3MW/cm 2. The corresponding pulse energy is 22.5µJ. The dependency between pulse width, scanning velocity and material removal efficiency is presented in Figure 5. The maximum of the material removal rate shifts to longer pulses for lower repetition rates. At 20kHz the highest material removal rate is achieved with a pulse width of 320ns. For these settings the pulse energy is 113µJ, the peak power is 350W and the average power density in the laser spot is 71.6MW/cm ) w mrrvs 150 mm's 200mm's 300 mms 400mm/s 800mm/s Pulse width ns] Repetition rate: 100kHz 3.0 o a, ' Pulse width [ns] Repetition rate: 20kHz 100 mms 150 mm1s 200 mms 300 mms 400 mrrvs 600 mms 800 mm1s Fig. 5. Material removal as a function of pulse width and scanning speed The material removal rate is also affected by the scanning velocity. This effect is observed especially for high repetition rates. Figure 6 shows the dependency between the scanning speed and the material removal rate [mm 3 /min]. For samples that were processed at 100 khz frequency the material removal rate starts to decrease when the scanning velocity drops below approximately 300mm/s. At this speed, the individual pulses overlap by 88 to 92%, with the pulseto-pulse distance being only 2 to 3µm. For values higher than 300mm/s the removal rate is rather constant and independent of the scanning velocity. At a repetition rate of 60kHz a similar decrease in the ablation rate occurs at velocities lower than 150 to 200mm/s. This setting results in a pulse-to-pulse distance of 2.5 to 3.3µm and the pulses overlap by 10 to 13%. No distinct correlation between the scanning velocity and the removal rate is observed at a repetition rate of 20kHz. However, the surfaces created at low repetition rates and low scanning velocity are also very rough and therefore, the measurement of the ablated material volume is less accurate. Proc. of SPI Vol G-4

5 > o ns 320ns l6ons 80 ns 40 ns 20 ns Scanning velocity [mm s1] Fig. 6. Material removal rate as a function of scanning velocity and pulse width The ablation process was optimized for highest material removal rate or surface quality. The highest ablation rate as a function of input energy was achieved at 20kHz repetition rate, 320ns pulse width and 150mm/s scanning velocity. At these settings the removed material volume per laser energy was 3.4mm 3 /kj and the ablation rate was 0.46mm 3 /min. However, the surfaces obtained at low repetition rates or low scanning velocities are very rough with peak-to-valley values exceeding 15µm. In general, operating at maximum material removal rates leads to unacceptable surface quality for engraving applications. Figure 7 (left) shows the surface appearance of a sample processing at highest removal rate. In addition to the rough surface there are also small cavities that occur randomly. For comparison, Figure 7 (right) presents the result after optimizing the parameter settings towards high surface quality. '': jil Pulse width: 320ns Repetition rate: 20kHz Scanning speed: 150mm/s Pulse width: 160ns Repetition rate: 100kHz Scanning speed: 800mm/s Fig. 7 Surface appearance for different processing conditions Post-treated surface Proc. of SPI Vol G-5

6 Shorter pulses, increased scanning velocity and repetition rates lead to the significantly improved surface appearance. ven further enhancements are possible if the sample is post processed using parameter settings that do not ablate additional material but remelt a thin layer and smooth out the surface profile. The power was set to 4.5W on work piece surface for all investigation performed with the 163mm focusing optic. Overall, highest material removal [mm 3 /kj] is achieved at a low repetition rate and a pulse width ranging from 160 to 320ns. The optimal material removal rate depends primarily on the dependency between pulse width and frequency. At 100kHz the highest material removal rate is obtained using a pulse width of 80ns, which corresponds to a peak power of 560W and an average power density in the laser spot of 35.4 MW/cm 2. The pulse energy for this setting is 45µJ. The maximum material removal rate shifts to longer pulses when the frequency is decreased. At 40kHz repetition rate, the maximum is at 160ns and at 20kHz, the maximum is observed at a pulse width of 320ns. The peak power is 700W and the average intensity is 44.2MW/cm 2 in both settings. The scanning velocity does not significantly effect the material removal rate and only slight changes occur. For higher frequency (100kHz), the material removal rate is rather constant regardless of the velocity. However, at low repetition frequency of 20 khz, the material removal rate increases with rising scanning velocity up to 800mm/s for pulse width of 160 and 32ns. Other pulse parameters maintained a rather constant material removal rate, regardless of the scanning velocity. 3.2 Processing of Silicon The objective of processing experiments carried out on silicon wafers was to drill holes and to scribe grooves. The purpose was to determine possible ablation rates and the processing quality and to estimate the optimal parameter settings for silicon processing. Grooves of 40mm length were scribed to the silicon sample using scanning velocities ranging from 200 to 2000mm/s, frequencies between 20 to 200kHz and the pulse widths from 20 to 320ns. All samples were processed using the 80mm focal length focusing optic that produces a spot size of 25µm. The laser power on the work piece surface was 4.5 W. The depth of each groove was measured; however this applies only to samples in which the relationship between the scanning velocity and frequency was such that a continuous groove is scribed. Some samples exhibit a large amount of recast and debris preventing an accurate measurement of the groove depth. The groove depth is measured from the top level of the sample to the highest and lowest point at the bottom of the groove. The depth is an average value of these measurements. Generally, the groove depth is maximized at low velocities; a fact that is mainly due to the higher energy per length. The achievable groove depth at 100kHz is shown in Figure 8 (left). The repetition rate has also a significant effect on the ablation rate. The higher ablation rates are observed with decreasing frequency ns 25 l6ons 20 a) 15 8Ons Ons 2Ons Scanning velocity [mm s'] rmvs 300 rrmls 400 rrmfs 500 rrm/s 600 rrmfs 800 rrrfs 1000 rin* 1500 rrn* 2000 rrn* Pulse width ns] Fig. 8. Groove depth as a function of scanning velocity and pulse width at a frequency 100kHz However, low frequencies limit the applicable scanning velocity, since high velocities result a series of single pulses, but not in a continuous groove. On the other hand, high frequency and low scanning velocity lead to a strong formation of recast and the material ejection from the groove is insufficient. Proc. of SPI Vol G-6

7 The depth of the groove is also affected by the pulse width. Short pulses remove only a limited amount of material, while longer pulses result in a considerable increase of the material removal rate (Figure 8 right). However, extending the pulse width also reduces the groove quality and eventually stops the ejection of material. A significant amount of recast is formed, especially at slow scanning velocities. The best quality for scribing grooves in silicon is achieved using a scanning velocity 600mm/s, a repetition rate of 100kHz and a pulse width of 160ns. The edges of the groove are melted and the quality is very consistent. The depth of the groove is 15µm. Figure 9 shows an example for such a groove. Fig. 9. Laser machined groove in silicon (depth 15µm) Single pulses were applied to the surface of the silicon wafer to investigate the effect of the pulse duration on the ablation phenomenon. Three different pulse widths were selected: 20, 80, 320, and 1000ns. In each case, the pulse energy was maintained at 45µJ, only the pulse width was been changed. The 1000ns pulse only heated and melted the surface of the material, but hardly removed any material. In this case the resulting peak power was only 45W and the average intensity in the laser spot 9.2MW/cm 2. By shortening the pulse to 320ns material is ablated and a clean funnel shaped blind hole with a very small amount of recast is formed. The peak power is 140W and the average intensity is 28.6MW/cm 2. Further compression of the pulse width to 80ns clearly induces a more aggressive impact and but the material removal is not very efficient and leaves a blind hole with a depth of only 4µm. The material removal is further reduced at a pulse width of 20ns. The created dimple is less than 2 micrometer deep and a large amount of debris is observed effected area. In this case, the peak power is 2.25kW and average intensity 458MW/cm 2. Figure 10 shows processing results for pulse lengths of 20 and 320ns. Pulse width: 320ns, peak power: 140W, depth: 15µm Fig. 10. Processing results in single pulse mode on silicon Pulse width: 20ns, peak power: 2.2kW, depth: >2µm Proc. of SPI Vol G-7

8 4. SUMMARY AND CONCLUSIONS A new pulsed fiber laser with flexible pulse width, repetition rate, and pulse energy is introduced and results on micromachining of metal and silicon are presented. The experiments show a pronounced effect of the pulse width on the quality and efficiency of the processes. Optimized settings for the pulse width and peak intensity are determined that result in highest removal rates or high surface quality. The material removal rates drop rapidly if the optimum intensity is exceeded. Factors that are assumed to cause this reduction in process efficiency include intra-pulse plasma effects and exothermic reactions during processing. A minimum intensity is required to exceed the ablation threshold of the material and to establish efficient material removal. The high flexibility of the laser source allows exploring a wide parameter range and offers extended capabilities in determining optimum processing conditions for specific materials. Proc. of SPI Vol G-8

Practical Applications of Laser Technology for Semiconductor Electronics

Practical Applications of Laser Technology for Semiconductor Electronics Practical Applications of Laser Technology for Semiconductor Electronics MOPA Single Pass Nanosecond Laser Applications for Semiconductor / Solar / MEMS & General Manufacturing Mark Brodsky US Application

More information

Rear Side Processing of Soda-Lime Glass Using DPSS Nanosecond Laser

Rear Side Processing of Soda-Lime Glass Using DPSS Nanosecond Laser Lasers in Manufacturing Conference 215 Rear Side Processing of Soda-Lime Glass Using DPSS Nanosecond Laser Juozas Dudutis*, Paulius Gečys, Gediminas Račiukaitis Center for Physical Sciences and Technology,

More information

Marking Cutting Welding Micro Machining Additive Manufacturing

Marking Cutting Welding Micro Machining Additive Manufacturing Marking Cutting Welding Micro Machining Additive Manufacturing Slide: 1 CM-F00003 Rev 4 G4 Pulsed Fiber Laser Slide: 2 CM-F00003 Rev 4 Versatility for Industry Automotive 2D/3D Cutting Night & Day Marking

More information

High peak power pulsed single-mode linearly polarized LMA fiber amplifier and Q-switch laser

High peak power pulsed single-mode linearly polarized LMA fiber amplifier and Q-switch laser High peak power pulsed single-mode linearly polarized LMA fiber amplifier and Q-switch laser V. Khitrov*, B. Samson, D. Machewirth, D. Yan, K. Tankala, A. Held Nufern, 7 Airport Park Road, East Granby,

More information

Precision Cold Ablation Material Processing using High-Power Picosecond Lasers

Precision Cold Ablation Material Processing using High-Power Picosecond Lasers Annual meeting Burgdorf Precision Cold Ablation Material Processing using High-Power Picosecond Lasers Dr. Kurt Weingarten kw@time-bandwidth.com 26 November 2009 Background of Time-Bandwidth Products First

More information

End Capped High Power Assemblies

End Capped High Power Assemblies Fiberguide s end capped fiber optic assemblies allow the user to achieve higher coupled power into a fiber core by reducing the power density at the air/ silica interface, commonly the point of laser damage.

More information

Ultrafast Lasers with Radial and Azimuthal Polarizations for Highefficiency. Applications

Ultrafast Lasers with Radial and Azimuthal Polarizations for Highefficiency. Applications WP Ultrafast Lasers with Radial and Azimuthal Polarizations for Highefficiency Micro-machining Applications Beneficiaries Call Topic Objective ICT-2013.3.2 Photonics iii) Laser for Industrial processing

More information

ICALEO 2007, October 29 November 1, Hilton in the WALT DISNEY WORLD Resort, Orlando, FL, USA

ICALEO 2007, October 29 November 1, Hilton in the WALT DISNEY WORLD Resort, Orlando, FL, USA WHAT IS THE BEST CHOICE FOR LASER MATERIAL PROCESSING ROD, DISK, SLAB OR FIBER? Paper 201 Erwin Steiger Erwin Steiger LaserService, Graf-Toerring-Strasse 68, Maisach, Bavaria, 82216, Germany Abstract Laser

More information

Lasers à fibres ns et ps de forte puissance. Francois SALIN EOLITE systems

Lasers à fibres ns et ps de forte puissance. Francois SALIN EOLITE systems Lasers à fibres ns et ps de forte puissance Francois SALIN EOLITE systems Solid-State Laser Concepts rod temperature [K] 347 -- 352 342 -- 347 337 -- 342 333 -- 337 328 -- 333 324 -- 328 319 -- 324 315

More information

Photonic Crystal Fiber Interfacing. In partnership with

Photonic Crystal Fiber Interfacing. In partnership with Photonic Crystal Fiber Interfacing In partnership with Contents 4 Photonics Crystal Fibers 6 End-capping 8 PCF connectors With strong expertise in designing fiber lasers and fused fiber components, ALPhANOV,

More information

High power UV from a thin-disk laser system

High power UV from a thin-disk laser system High power UV from a thin-disk laser system S. M. Joosten 1, R. Busch 1, S. Marzenell 1, C. Ziolek 1, D. Sutter 2 1 TRUMPF Laser Marking Systems AG, Ausserfeld, CH-7214 Grüsch, Switzerland 2 TRUMPF Laser

More information

FIBER LASERS Ytterbium, Thulium and Erbium short pulse and CW lasers

FIBER LASERS Ytterbium, Thulium and Erbium short pulse and CW lasers About V-Gen V-Gen develops, manufactures and markets high quality innovative laser systems for a wide range of industrial applications. The company s laser systems are the product of extensive experience

More information

1 kw, 15!J linearly polarized fiber laser operating at 977 nm

1 kw, 15!J linearly polarized fiber laser operating at 977 nm 1 kw, 15!J linearly polarized fiber laser operating at 977 nm V. Khitrov, D. Machewirth, B. Samson, K. Tankala Nufern, 7 Airport Park Road, East Granby, CT 06026 phone: (860) 408-5000; fax: (860)408-5080;

More information

Single frequency MOPA system with near diffraction limited beam

Single frequency MOPA system with near diffraction limited beam Single frequency MOPA system with near diffraction limited beam quality D. Chuchumishev, A. Gaydardzhiev, A. Trifonov, I. Buchvarov Abstract Near diffraction limited pulses of a single-frequency and passively

More information

Progress on High Power Single Frequency Fiber Amplifiers at 1mm, 1.5mm and 2mm

Progress on High Power Single Frequency Fiber Amplifiers at 1mm, 1.5mm and 2mm Nufern, East Granby, CT, USA Progress on High Power Single Frequency Fiber Amplifiers at 1mm, 1.5mm and 2mm www.nufern.com Examples of Single Frequency Platforms at 1mm and 1.5mm and Applications 2 Back-reflection

More information

High Rep-Rate KrF Laser Development and Intense Pulse Interaction Experiments for IFE*

High Rep-Rate KrF Laser Development and Intense Pulse Interaction Experiments for IFE* High Rep-Rate KrF Laser Development and Intense Pulse Interaction Experiments for IFE* Y. Owadano, E. Takahashi, I. Okuda, I. Matsushima, Y. Matsumoto, S. Kato, E. Miura and H.Yashiro 1), K. Kuwahara 2)

More information

Fiber lasers and their advanced optical technologies of Fujikura

Fiber lasers and their advanced optical technologies of Fujikura Fiber lasers and their advanced optical technologies of Fujikura Kuniharu Himeno 1 Fiber lasers have attracted much attention in recent years. Fujikura has compiled all of the optical technologies required

More information

Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping

Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping Albert Töws and Alfred Kurtz Cologne University of Applied Sciences Steinmüllerallee 1, 51643 Gummersbach, Germany

More information

Thin-Disc-Based Driver

Thin-Disc-Based Driver Thin-Disc-Based Driver Jochen Speiser German Aerospace Center (DLR) Institute of Technical Physics Solid State Lasers and Nonlinear Optics Folie 1 German Aerospace Center! Research Institution! Space Agency!

More information

Advances in Laser Micro-machining for Wafer Probing and Trimming

Advances in Laser Micro-machining for Wafer Probing and Trimming Advances in Laser Micro-machining for Wafer Probing and Trimming M.R.H. Knowles, A.I.Bell, G. Rutterford & A. Webb Oxford Lasers June 10, 2002 Oxford Lasers June 2002 1 Introduction to Laser Micro-machining

More information

Advanced seeders for fiber lasers - IFLA. 23 June. 2014

Advanced seeders for fiber lasers - IFLA. 23 June. 2014 Advanced seeders for fiber lasers - IFLA 23 June. 2014 Seeders - introduction In MOPA * pulsed fiber lasers, seeders largely impact major characteristics of the laser system: Optical spectrum Peak power

More information

MULTI-STAGE YTTERBIUM FIBER-AMPLIFIER SEEDED BY A GAIN-SWITCHED LASER DIODE

MULTI-STAGE YTTERBIUM FIBER-AMPLIFIER SEEDED BY A GAIN-SWITCHED LASER DIODE MULTI-STAGE YTTERBIUM FIBER-AMPLIFIER SEEDED BY A GAIN-SWITCHED LASER DIODE Authors: M. Ryser, S. Pilz, A. Burn, V. Romano DOI: 10.12684/alt.1.101 Corresponding author: e-mail: M. Ryser manuel.ryser@iap.unibe.ch

More information

GRADE A ENGRAVING. Application-focused DPSS laser outshines industry favorite fiber laser counterpart when marking components

GRADE A ENGRAVING. Application-focused DPSS laser outshines industry favorite fiber laser counterpart when marking components GRADE A ENGRAVING by Marin Iliev, R&D manager, RMI Laser Application-focused DPSS laser outshines industry favorite fiber laser counterpart when marking components No doubt fiber lasers are the most common

More information

Development of High-peak Power Yb-doped Fiber Laser in Large Core Fiber

Development of High-peak Power Yb-doped Fiber Laser in Large Core Fiber Development of High-peak Power Yb-doped Fiber Laser in Large Core Fiber Institute of Laser Engineering Osaka University Hidetsugu Yoshida Koji Tsubakimoto Hisanori Fujita Masahiro Nakatsuka Noriaki Miyanaga

More information

PERFORMANCE OF PHOTODIGM S DBR SEMICONDUCTOR LASERS FOR PICOSECOND AND NANOSECOND PULSING APPLICATIONS

PERFORMANCE OF PHOTODIGM S DBR SEMICONDUCTOR LASERS FOR PICOSECOND AND NANOSECOND PULSING APPLICATIONS PERFORMANCE OF PHOTODIGM S DBR SEMICONDUCTOR LASERS FOR PICOSECOND AND NANOSECOND PULSING APPLICATIONS By Jason O Daniel, Ph.D. TABLE OF CONTENTS 1. Introduction...1 2. Pulse Measurements for Pulse Widths

More information

Beam Shaping in High-Power Laser Systems with Using Refractive Beam Shapers

Beam Shaping in High-Power Laser Systems with Using Refractive Beam Shapers - 1 - Beam Shaping in High-Power Laser Systems with Using Refractive Beam Shapers Alexander Laskin, Vadim Laskin AdlOptica GmbH, Rudower Chaussee 29, 12489 Berlin, Germany ABSTRACT Beam Shaping of the

More information

Concepts for High Power Laser Diode Systems

Concepts for High Power Laser Diode Systems Concepts for High Power Laser Diode Systems 1. Introduction High power laser diode systems is a new development within the field of laser diode systems. Pioneer of such laser systems was SDL, Inc. which

More information

Improving efficiency of CO 2

Improving efficiency of CO 2 Improving efficiency of CO 2 Laser System for LPP Sn EUV Source K.Nowak*, T.Suganuma*, T.Yokotsuka*, K.Fujitaka*, M.Moriya*, T.Ohta*, A.Kurosu*, A.Sumitani** and J.Fujimoto*** * KOMATSU ** KOMATSU/EUVA

More information

High Power Thin Disk Lasers. Dr. Adolf Giesen. German Aerospace Center. Institute of Technical Physics. Folie 1. Institute of Technical Physics

High Power Thin Disk Lasers. Dr. Adolf Giesen. German Aerospace Center. Institute of Technical Physics. Folie 1. Institute of Technical Physics High Power Thin Disk Lasers Dr. Adolf Giesen German Aerospace Center Folie 1 Research Topics - Laser sources and nonlinear optics Speiser Beam control and optical diagnostics Riede Atm. propagation and

More information

Development of Nano Second Pulsed Lasers Using Polarization Maintaining Fibers

Development of Nano Second Pulsed Lasers Using Polarization Maintaining Fibers Development of Nano Second Pulsed Lasers Using Polarization Maintaining Fibers Shun-ichi Matsushita*, * 2, Taizo Miyato*, * 2, Hiroshi Hashimoto*, * 2, Eisuke Otani* 2, Tatsuji Uchino* 2, Akira Fujisaki*,

More information

5kW DIODE-PUMPED TEST AMPLIFIER

5kW DIODE-PUMPED TEST AMPLIFIER 5kW DIODE-PUMPED TEST AMPLIFIER SUMMARY?Gain - OK, suggest high pump efficiency?efficient extraction - OK, but more accurate data required?self-stabilisation - Yes, to a few % but not well matched to analysis

More information

AVIA DPSS Lasers: Advanced Design for Increased Process Throughput

AVIA DPSS Lasers: Advanced Design for Increased Process Throughput White Paper AVIA DPSS Lasers: Advanced Design for Increased Process Throughput The Q-switched, diode-pumped, solid-state (DPSS) laser has become a widely employed tool in a broad range of industrial micromachining

More information

Integrated disruptive components for 2µm fibre Lasers ISLA. 2 µm Sub-Picosecond Fiber Lasers

Integrated disruptive components for 2µm fibre Lasers ISLA. 2 µm Sub-Picosecond Fiber Lasers Integrated disruptive components for 2µm fibre Lasers ISLA 2 µm Sub-Picosecond Fiber Lasers Advantages: 2 - microns wavelength offers eye-safety potentially higher pulse energy and average power in single

More information

The Development of a High Quality and a High Peak Power Pulsed Fiber Laser With a Flexible Tunability of the Pulse Width

The Development of a High Quality and a High Peak Power Pulsed Fiber Laser With a Flexible Tunability of the Pulse Width The Development of a High Quality and a High Peak Power Pulsed Fiber Laser With a Flexible Tunability of the Pulse Width Ryo Kawahara *1, Hiroshi Hashimoto *1, Jeffrey W. Nicholson *2, Eisuke Otani *1,

More information

Dicing of Thin Silicon Wafers with Ultra-Short Pulsed Lasers in the Range from 200 fs up to 10 ps

Dicing of Thin Silicon Wafers with Ultra-Short Pulsed Lasers in the Range from 200 fs up to 10 ps Technical Communication JLMN-Journal of Laser Micro/Nanoengineering Vol. 10, No. 2, 2015 Dicing of Thin Silicon Wafers with Ultra-Short Pulsed Lasers in the Range from 200 fs up to 10 ps C. Fornaroli 1,

More information

High Power Dense Spectral Combination Using Commercially Available Lasers and VHGs

High Power Dense Spectral Combination Using Commercially Available Lasers and VHGs High Power Dense Spectral Combination Using Commercially Available Lasers and VHGs Christophe Moser, CEO Moser@ondax.com Contributors: Gregory Steckman, Frank Havermeyer, Wenhai Liu: Ondax Inc. Christian

More information

NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA

NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA Abstract: A novel interferometric scheme for detection of ultrasound is presented.

More information

Development of scalable laser technology for EUVL applications

Development of scalable laser technology for EUVL applications Development of scalable laser technology for EUVL applications Tomáš Mocek, Ph.D. Chief Scientist & Project Leader HiLASE Centre CZ.1.05/2.1.00/01.0027 Lasers for real-world applications Laser induced

More information

Continuum White Light Generation. WhiteLase: High Power Ultrabroadband

Continuum White Light Generation. WhiteLase: High Power Ultrabroadband Continuum White Light Generation WhiteLase: High Power Ultrabroadband Light Sources Technology Ultrafast Pulses + Fiber Laser + Non-linear PCF = Spectral broadening from 400nm to 2500nm Ultrafast Fiber

More information

1550 nm Programmable Picosecond Laser, PM

1550 nm Programmable Picosecond Laser, PM 1550 nm Programmable Picosecond Laser, PM The Optilab is a programmable laser that produces picosecond pulses with electrical input pulses. It functions as a seed pulse generator for Master Oscillator

More information

Designing for Femtosecond Pulses

Designing for Femtosecond Pulses Designing for Femtosecond Pulses White Paper PN 200-1100-00 Revision 1.1 July 2013 Calmar Laser, Inc www.calmarlaser.com Overview Calmar s femtosecond laser sources are passively mode-locked fiber lasers.

More information

Sub-ns Microchip Lasers Technology: Overview and Progress in Health Science and Industrial Applications Florent Thibault

Sub-ns Microchip Lasers Technology: Overview and Progress in Health Science and Industrial Applications Florent Thibault Sub-ns Microchip Lasers Technology: Overview and Progress in Health Science and Industrial Applications Florent Thibault May 2012/ page 1 Agenda 1. Company overview 2. Laser technology 3. Added value for

More information

Features. Applications. Optional Features

Features. Applications. Optional Features Features Compact, Rugged Design TEM Beam with M 2 < 1.2 Pulse Rates from Single Shot to 15 khz IR, Green, UV, and Deep UV Wavelengths Available RS232 Computer Control Patented Harmonic Generation Technology

More information

Fiber Lasers for EUV Lithography

Fiber Lasers for EUV Lithography Fiber Lasers for EUV Lithography A. Galvanauskas, Kai Chung Hou*, Cheng Zhu CUOS, EECS Department, University of Michigan P. Amaya Arbor Photonics, Inc. * Currently with Cymer, Inc 2009 International Workshop

More information

LASER TECHNOLOGY. Key parameters. Groundbreaking in the laser processing of cutting tools. A member of the UNITED GRINDING Group

LASER TECHNOLOGY. Key parameters. Groundbreaking in the laser processing of cutting tools. A member of the UNITED GRINDING Group Creating Tool Performance A member of the UNITED GRINDING Group Groundbreaking in the laser processing of cutting tools Key parameters The machining of modern materials using laser technology knows no

More information

Application of EOlite Flexible Pulse Technology. Matt Rekow Yun Zhou Nicolas Falletto

Application of EOlite Flexible Pulse Technology. Matt Rekow Yun Zhou Nicolas Falletto Application of EOlite Flexible Pulse Technology Matt Rekow Yun Zhou Nicolas Falletto 1 Topics Company Background What is a Flexible Pulse Laser? Why Tailored or Flexible Pulse? Application of Flexible

More information

Fiber Laser Chirped Pulse Amplifier

Fiber Laser Chirped Pulse Amplifier Fiber Laser Chirped Pulse Amplifier White Paper PN 200-0200-00 Revision 1.2 January 2009 Calmar Laser, Inc www.calmarlaser.com Overview Fiber lasers offer advantages in maintaining stable operation over

More information

Variable Pulse Duration Laser for Material Processing

Variable Pulse Duration Laser for Material Processing JLMN-Journal of Laser Micro/Nanoengineering Vol., No. 1, 7 Variable Pulse Duration Laser for Material Processing Werner Wiechmann, Loren Eyres, James Morehead, Jeffrey Gregg, Derek Richard, Will Grossman

More information

Laser-Produced Sn-plasma for Highvolume Manufacturing EUV Lithography

Laser-Produced Sn-plasma for Highvolume Manufacturing EUV Lithography Panel discussion Laser-Produced Sn-plasma for Highvolume Manufacturing EUV Lithography Akira Endo * Extreme Ultraviolet Lithography System Development Association Gigaphoton Inc * 2008 EUVL Workshop 11

More information

Atlantic. Industrial High Power Picosecond Lasers. features

Atlantic. Industrial High Power Picosecond Lasers. features Atlantic Industrial High Power Picosecond Lasers lasers have been designed as a versatile tool for a variety of industrial material processing applications. They are compact, OEM rugged, with up to 8 W

More information

HIGH POWER LASERS FOR 3 RD GENERATION GRAVITATIONAL WAVE DETECTORS

HIGH POWER LASERS FOR 3 RD GENERATION GRAVITATIONAL WAVE DETECTORS HIGH POWER LASERS FOR 3 RD GENERATION GRAVITATIONAL WAVE DETECTORS P. Weßels for the LZH high power laser development team Laser Zentrum Hannover, Germany 23.05.2011 OUTLINE Requirements on lasers for

More information

DCS laser for Thomson scattering diagnostic applications

DCS laser for Thomson scattering diagnostic applications DCS laser for Thomson scattering diagnostic applications Authors Jason Zweiback 10/6/2015 jzweiback@logostech.net 1 Summary Motivation DCS laser Laser for Thomson scattering diagnostics 2 What is the Dynamic

More information

UNMATCHED OUTPUT POWER AND TUNING RANGE

UNMATCHED OUTPUT POWER AND TUNING RANGE ARGOS MODEL 2400 SF SERIES TUNABLE SINGLE-FREQUENCY MID-INFRARED SPECTROSCOPIC SOURCE UNMATCHED OUTPUT POWER AND TUNING RANGE One of Lockheed Martin s innovative laser solutions, Argos TM Model 2400 is

More information

Vixar High Power Array Technology

Vixar High Power Array Technology Vixar High Power Array Technology I. Introduction VCSELs arrays emitting power ranging from 50mW to 10W have emerged as an important technology for applications within the consumer, industrial, automotive

More information

FemtoFAB. Femtosecond laser micromachining system. tel fax Konstitucijos ave. 23C LT Vilnius, Lithuania

FemtoFAB. Femtosecond laser micromachining system. tel fax Konstitucijos ave. 23C LT Vilnius, Lithuania FemtoFAB Femtosecond laser micromachining system Konstitucijos ave. 23C LT-08105 Vilnius, Lithuania tel. +370 5 272 57 38 fax +370 5 272 37 04 info@wophotonics.com www.wophotonics.com INTRODUCTION FemtoFAB

More information

COHERENT BEAM COMBINING OF HIGH POWER LASERS FOR MATERIALS PROCESSING

COHERENT BEAM COMBINING OF HIGH POWER LASERS FOR MATERIALS PROCESSING COHERENT BEAM COMBINING OF HIGH POWER LASERS FOR MATERIALS PROCESSING www.civan.co.il EXECUTIVE SUMMARY Civan Advanced Technologies develops and manufactures single-mode, highpower laser systems with a

More information

Robustness and high MTBF, to guarantee availability, even in harsh industrial environments. Maintenance-free, thereby eliminating maintenance

Robustness and high MTBF, to guarantee availability, even in harsh industrial environments. Maintenance-free, thereby eliminating maintenance Efficient Industrial Application of Near-Infrared Laser Sources Fiber lasers, Nd:YAG or Nd:YVO lasers may be combined with either flatbed or galvanometer systems as well as with fixed-beam systems for

More information

ModBox-FE-125ps-10mJ. Performance Highlights FEATURES APPLICATIONS. Electrical & Optical Pulse Diagrams

ModBox-FE-125ps-10mJ. Performance Highlights FEATURES APPLICATIONS. Electrical & Optical Pulse Diagrams The System-FE-1064nm is set to generate short shaped pulses with high extinction ratio at 1064.1 nm. It allows dynamic extinction ratio up to 55 db with user adjustable pulse duration, repetition rate

More information

Mitigation of Self-Pulsing in High Power Pulsed Fiber Lasers

Mitigation of Self-Pulsing in High Power Pulsed Fiber Lasers Mitigation of Self-Pulsing in High Power Pulsed Fiber Lasers Yusuf Panbiharwala, Deepa Venkitesh, Balaji Srinivasan* Department of Electrical Engineering, Indian Institute of Technology Madras. *Email

More information

Atlantic. series. Industrial High Power Picosecond DPSS Lasers

Atlantic. series. Industrial High Power Picosecond DPSS Lasers Atlantic series Industrial High Power Picosecond DPSS Lasers Laser description Laser micromachining is rapidly becoming the material processing technology of choice for numerous small scale, real world

More information

directly on each side of the crystal to form a rugged, monolithic oscillator that is end pumped by a CW diode laser.

directly on each side of the crystal to form a rugged, monolithic oscillator that is end pumped by a CW diode laser. Product Bulletin MicroChip NanoPulse, NanoGreen, and NanoEyeSafe CDRH Solid-State Lasers The JDS Uniphase MicroChip NanoLaser produces high peak power, high repetition rates, and short pulses from compact,

More information

High power VCSEL array pumped Q-switched Nd:YAG lasers

High power VCSEL array pumped Q-switched Nd:YAG lasers High power array pumped Q-switched Nd:YAG lasers Yihan Xiong, Robert Van Leeuwen, Laurence S. Watkins, Jean-Francois Seurin, Guoyang Xu, Alexander Miglo, Qing Wang, and Chuni Ghosh Princeton Optronics,

More information

Mikrobohren mit gepulsten Faserlasern

Mikrobohren mit gepulsten Faserlasern Mikrobohren mit gepulsten Faserlasern Ronald Holtz (Class 4 Laser Professionals AG) Christoph Rüttimann, Noémie Dury (Rofin Lasag AG) Content - Market and applications overview - Properties of lamp pumped

More information

Midaz Micro-Slab DPSS Lasers:

Midaz Micro-Slab DPSS Lasers: Midaz Micro-Slab DPSS Lasers: Higher power & pulse rate for higher speed micromachining Professor Mike Damzen Midaz Laser Ltd 4 June 2008 AILU Meeting Industrial opportunities in laser micro and nano processing

More information

Recent Progress in Active Fiber Designs and Monolithic High Power Fiber Laser Devices. Kanishka Tankala, Adrian Carter and Bryce Samson

Recent Progress in Active Fiber Designs and Monolithic High Power Fiber Laser Devices. Kanishka Tankala, Adrian Carter and Bryce Samson Recent Progress in Active Fiber Designs and Monolithic High Power Fiber Laser Devices Kanishka Tankala, Adrian Carter and Bryce Samson Advantages of Fiber Lasers Features Highly efficient diode pumped

More information

Flexible and Programmable Pulse Shaping MOPA Fiber Laser Platform, Performances and Applications

Flexible and Programmable Pulse Shaping MOPA Fiber Laser Platform, Performances and Applications Special Issue Flexible and Programmable Pulse Shaping MOPA Fiber Laser Platform, Performances and Applications Louis DESBIENS, 1 Pascal DELADURANTAYE, 1 Alain COURNOYER, 1 David GAY, 1 Claude PARÉ, 1 Sasia

More information

Fiber lasers: The next generation

Fiber lasers: The next generation Fiber lasers: The next generation David N Payne Optoelectronics Research Centre and SPI Lasers kw fibre laser No connection! After the telecoms EDFA The fibre laser another fibre revolution? Fibre laser

More information

POWER DETECTORS. How they work POWER DETECTORS. Overview

POWER DETECTORS. How they work POWER DETECTORS. Overview G E N T E C - E O POWER DETECTORS Well established in this field for over 30 years Gentec Electro-Optics has been a leader in the field of laser power and energy measurement. The average power density

More information

New random trigger-feature for ultrashort-pulsed laser increases throughput, accuracy and quality in micromachining applications

New random trigger-feature for ultrashort-pulsed laser increases throughput, accuracy and quality in micromachining applications New random trigger-feature for ultrashort-pulsed laser increases throughput, accuracy and quality in micromachining applications Andreas Oehler* a, Hubert Ammann a, Marco Benetti a, Dominique Wassermann

More information

Novel laser power sensor improves process control

Novel laser power sensor improves process control Novel laser power sensor improves process control A dramatic technological advancement from Coherent has yielded a completely new type of fast response power detector. The high response speed is particularly

More information

Gigashot TM FT High Energy DPSS Laser

Gigashot TM FT High Energy DPSS Laser Gigashot TM FT High Energy DPSS Laser Northrop Grumman Cutting Edge Optronics (636) 916-4900 / Email: st-ceolaser-info@ngc.com 2015 Northrop Grumman Systems Corporation Gigashot TM FT Key Specifications

More information

High-peak power laser system used in Yb doped LMA fiber

High-peak power laser system used in Yb doped LMA fiber High-peak power laser system used in Yb doped LMA fiber Institute of Laser Engineering, Osaka University, Suita, Osaka, Japan YOSHIDA Hidetsugu, TSUBAKIMOTO Koji, FUJITA Hisanori, NAKATSUKA Masahiro, MIYANAGA

More information

SURFACE ANALYSIS STUDY OF LASER MARKING OF ALUMINUM

SURFACE ANALYSIS STUDY OF LASER MARKING OF ALUMINUM SURFACE ANALYSIS STUDY OF LASER MARKING OF ALUMINUM Julie Maltais 1, Vincent Brochu 1, Clément Frayssinous 2, Réal Vallée 3, Xavier Godmaire 4 and Alex Fraser 5 1. Summer intern 4. President 5. Chief technology

More information

SUPPLEMENTARY INFORMATION DOI: /NPHOTON

SUPPLEMENTARY INFORMATION DOI: /NPHOTON Supplementary Methods and Data 1. Apparatus Design The time-of-flight measurement apparatus built in this study is shown in Supplementary Figure 1. An erbium-doped femtosecond fibre oscillator (C-Fiber,

More information

This series of lasers are available with a choice of Nd:YAG, Nd:YLF, and Nd:YVO 4. System Reliability

This series of lasers are available with a choice of Nd:YAG, Nd:YLF, and Nd:YVO 4. System Reliability Photonics Industries DS Series of UV (351/355 nm) diode pumped solid-state Q-switched lasers offer a compact, hands-free system with the long-term reliability that the manufacturing industry demands. Utilizing

More information

PGx11 series. Transform Limited Broadly Tunable Picosecond OPA APPLICATIONS. Available models

PGx11 series. Transform Limited Broadly Tunable Picosecond OPA APPLICATIONS. Available models PGx1 PGx3 PGx11 PT2 Transform Limited Broadly Tunable Picosecond OPA optical parametric devices employ advanced design concepts in order to produce broadly tunable picosecond pulses with nearly Fourier-transform

More information

High Power and Energy Femtosecond Lasers

High Power and Energy Femtosecond Lasers High Power and Energy Femtosecond Lasers PHAROS is a single-unit integrated femtosecond laser system combining millijoule pulse energies and high average powers. PHAROS features a mechanical and optical

More information

Nmark AGV-HP. High Accuracy, Thermally Stable Galvo Scanner

Nmark AGV-HP. High Accuracy, Thermally Stable Galvo Scanner Nmark AGV-HP High Accuracy, Thermally Stable Galvo Scanner Highest accuracy scanner available attains single-digit, micron-level accuracy over the field of view Optical feedback technology significantly

More information

Elimination of Self-Pulsations in Dual-Clad, Ytterbium-Doped Fiber Lasers

Elimination of Self-Pulsations in Dual-Clad, Ytterbium-Doped Fiber Lasers Elimination of Self-Pulsations in Dual-Clad, Ytterbium-Doped Fiber Lasers 1.0 Modulation depth 0.8 0.6 0.4 0.2 0.0 Laser 3 Laser 2 Laser 4 2 3 4 5 6 7 8 Absorbed pump power (W) Laser 1 W. Guan and J. R.

More information

High-power fibre Raman lasers at the University of Southampton

High-power fibre Raman lasers at the University of Southampton High-power fibre Raman lasers at the University of Southampton Industry Day Southampton, April 2 2014 Johan Nilsson Optoelectronics Research Centre University of Southampton, England Also consultant to

More information

1272. Phase-controlled vibrational laser percussion drilling

1272. Phase-controlled vibrational laser percussion drilling 1272. Phase-controlled vibrational laser percussion drilling Chao-Ching Ho 1, Chih-Mu Chiu 2, Yuan-Jen Chang 3, Jin-Chen Hsu 4, Chia-Lung Kuo 5 National Yunlin University of Science and Technology, Douliou,

More information

High-Power Femtosecond Lasers

High-Power Femtosecond Lasers High-Power Femtosecond Lasers PHAROS is a single-unit integrated femtosecond laser system combining millijoule pulse energies and high average power. PHAROS features a mechanical and optical design optimized

More information

3D SCANNING LASER HARDENING. Matěj HRUŠKA, Marek VOSTŘÁK, Eva SMAZALOVÁ, Michal ŠVANTNER

3D SCANNING LASER HARDENING. Matěj HRUŠKA, Marek VOSTŘÁK, Eva SMAZALOVÁ, Michal ŠVANTNER 3D SCANNING LASER HARDENING Matěj HRUŠKA, Marek VOSTŘÁK, Eva SMAZALOVÁ, Michal ŠVANTNER University of West Bohemia, Pilsen, Czech Republic, EU, maslej@ntc.zcu.cz Abstract The laser scanning method uses

More information

Atlantic. Industrial High Power Picosecond Lasers. features

Atlantic. Industrial High Power Picosecond Lasers. features Atlantic Industrial High Picosecond Lasers lasers have been designed as a versatile tool for a variety of industrial material processing applications. They are compact, OEM rugged, with up to 8 W output

More information

Investigations on the performance of lidar measurements with different pulse shapes using a multi-channel Doppler lidar system

Investigations on the performance of lidar measurements with different pulse shapes using a multi-channel Doppler lidar system Th12 Albert Töws Investigations on the performance of lidar measurements with different pulse shapes using a multi-channel Doppler lidar system Albert Töws and Alfred Kurtz Cologne University of Applied

More information

PicoBlade 2 Picosecond Micromachining Laser. Precision and flexibility for optimized processes a fully featured, machine-ready system

PicoBlade 2 Picosecond Micromachining Laser. Precision and flexibility for optimized processes a fully featured, machine-ready system PicoBlade 2 Picosecond Micromachining Laser Precision and flexibility for optimized processes a fully featured, machine-ready system www.lumentum.com Data Sheet The PicoBlade 2 laser system is a versatile

More information

High Average Power, High Repetition Rate Side-Pumped Nd:YVO 4 Slab Laser

High Average Power, High Repetition Rate Side-Pumped Nd:YVO 4 Slab Laser High Average Power, High Repetition Rate Side-Pumped Nd:YVO Slab Laser Kevin J. Snell and Dicky Lee Q-Peak Incorporated 135 South Rd., Bedford, MA 173 (71) 75-9535 FAX (71) 75-97 e-mail: ksnell@qpeak.com,

More information

Drive Beam Photo-injector Option for the CTF3 Nominal Phase

Drive Beam Photo-injector Option for the CTF3 Nominal Phase CTF3 Review Drive Beam Photo-injector Option for the CTF3 Nominal Phase Motivation CTF3 Drive Beam Requirements CTF3 RF gun design The Laser (I. Ross / RAL) The Photocathode Cost estimate Possible schedule

More information

Progress and development in Fibre Laser technology

Progress and development in Fibre Laser technology Invited Paper Progress and development in Fibre Laser technology Ray Horley, Stephen Norman and Michalis N. Zervas (*) SPI Lasers UK Ltd, Southampton, UK; (*) also with Optoelectronics Research Centre,

More information

How to Properly Select a Laser Power or Energy Sensor

How to Properly Select a Laser Power or Energy Sensor How to Properly Select a Laser Power or Energy Sensor By Dick Rieley, Sales Manager, Mid Altantic and Southeast Regions, Ophir-Spiricon LLC The selection of a sensor to accurately measure the power of

More information

FPPO 1000 Fiber Laser Pumped Optical Parametric Oscillator: FPPO 1000 Product Manual

FPPO 1000 Fiber Laser Pumped Optical Parametric Oscillator: FPPO 1000 Product Manual Fiber Laser Pumped Optical Parametric Oscillator: FPPO 1000 Product Manual 2012 858 West Park Street, Eugene, OR 97401 www.mtinstruments.com Table of Contents Specifications and Overview... 1 General Layout...

More information

A new picosecond Laser pulse generation method.

A new picosecond Laser pulse generation method. PULSE GATING : A new picosecond Laser pulse generation method. Picosecond lasers can be found in many fields of applications from research to industry. These lasers are very common in bio-photonics, non-linear

More information

Power. Warranty. 30 <1.5 <3% Near TEM ~4.0 one year. 50 <1.5 <5% Near TEM ~4.0 one year

Power. Warranty. 30 <1.5 <3% Near TEM ~4.0 one year. 50 <1.5 <5% Near TEM ~4.0 one year DL CW Blue Violet Laser, 405nm 405 nm Operating longitudinal mode Several Applications: DNA Sequencing Spectrum analysis Optical Instrument Flow Cytometry Interference Measurements Laser lighting show

More information

Femtosecond to millisecond transient absorption spectroscopy: two lasers one experiment

Femtosecond to millisecond transient absorption spectroscopy: two lasers one experiment 7 Femtosecond to millisecond transient absorption spectroscopy: two lasers one experiment 7.1 INTRODUCTION The essential processes of any solar fuel cell are light absorption, electron hole separation

More information

High-Power, Passively Q-switched Microlaser - Power Amplifier System

High-Power, Passively Q-switched Microlaser - Power Amplifier System High-Power, Passively Q-switched Microlaser - Power Amplifier System Yelena Isyanova Q-Peak, Inc.,135 South Road, Bedford, MA 01730 isyanova@qpeak.com Jeff G. Manni JGM Associates, 6 New England Executive

More information

Power scaling of picosecond thin disc laser for LPP and FEL EUV sources

Power scaling of picosecond thin disc laser for LPP and FEL EUV sources Power scaling of picosecond thin disc laser for LPP and FEL EUV sources A. Endo 1,2, M. Smrz 1, O. Novak 1, T. Mocek 1, K.Sakaue 2 and M.Washio 2 1) HiLASE Centre, Institute of Physics AS CR, Dolní Břežany,

More information

High Peak Power Fiber Seeds & Efficient Stabilized Pumps

High Peak Power Fiber Seeds & Efficient Stabilized Pumps High Peak Power Fiber Seeds & Efficient Stabilized Pumps Features Ultra Narrow Spectral Bandwidth (< 100kHz Instantaneous for single mode diodes) Ultra Track Linear Tracking Photodiode Temperature Stabilized

More information

White Paper: Modifying Laser Beams No Way Around It, So Here s How

White Paper: Modifying Laser Beams No Way Around It, So Here s How White Paper: Modifying Laser Beams No Way Around It, So Here s How By John McCauley, Product Specialist, Ophir Photonics There are many applications for lasers in the world today with even more on the

More information

Micro-milling process improvement using an agile pulse-shaping fiber laser

Micro-milling process improvement using an agile pulse-shaping fiber laser Micro-milling process improvement using an agile pulse-shaping fiber laser David Gay, Alain Cournoyer, Pascal Deladurantaye, Martin Briand, Vincent Roy, Bruno Labranche, Marc Levesque and Yves Taillon

More information

Atlantic. Industrial High Power Picosecond Lasers. features

Atlantic. Industrial High Power Picosecond Lasers. features Industrial High Picosecond Lasers lasers have been designed as a versatile tool for a variety of industrial material processing applications. They are compact, OEM rugged, with up to 6 W output power at

More information