ADVR-2100M. Universal Hybrid Analog-Digital Voltage Regulator Operation Manual

Transcription

1 ADV-2100M Universal Hybrid Analog-Digital Voltage egulator Operation Manual Hybrid Universal Analog / Digital 1 or 3 Phase 5 Amp elf Excited, hunt, Auxiliary Winding, Harmonic Power or PMG Automatic Voltage egulator Easy to et-up and Program Install Manual KUAI ELECIC IDUY CO., LD. EL : FAX : Website : Headquarters : o.3, Lane 201, Chien Fu t., Chyan Jenn Dist., Kaohsiung 80664, AIWA

2 ECI 1 : PECIFICAI ensing Input (,, E3) Average eading tatic Power Dissipation Voltage Vac, 1 phase / 3 phase Max.12 watts DIP switch setting Vac Burden in HU & PMG Wiring / 440 Vac 550 power input 110 Vac / 600 Vac 1100 power input 220 Vac Frequency 50/60 Hz, DIP switch setting Quadrature Droop Input (C1, ) Power Input (P1, P2) C 1A or 5A greater than 5VA (DIP switch setting) Voltage Vac, 1 phase 2 wire ensitivity +/- PF +/- 0.5 (Droop adjustable) Frequency Hz Analogue Voltage Input (, ) Excitation Output (F+, F-) Input resistance greater than 2K ohms 110V 1 phase Continuous 63 Vdc 5A Max. Input +/- 5 Vdc or +10 Vdc Max. 90 Vdc 7A for 10 secs. ensitivity 1 Vdc for 2.5% Volts (adjustable) 220V 1 phase Continuous 125 Vdc 5A Max. 180 Vdc 7A for 10 secs. Under Frequency Protection (Factory Presets) 220V 3 phase Continuous 150 Vdc 5A 50 Hz system presets knee point at 45 Hz Max. 215 Vdc 7A for 10 secs. 60 Hz system presets knee point at 55 Hz esistance 13 power input 110 Vac 25 power input 220 Vac Over Excitation Protection Max. 100 ohms et point 125 Vdc +/- 4 power input 220 Vac Fuse pec. low blow 5 x 20 mm 505-5A Inverse-time curve. his function can be turned off. External Voltage Adjustment (V1, V2) Voltage hermal Drift Max. +/- 500 ohms 1 watt potentiometer Less than 3% at temperature range -40 to +70 C Max. +/- 1K ohm 1 watt potentiometer Under-Frequency Knee Point hermal Drift Voltage egulation Less than +/- 0.1 Hz at -40 to +70 C Less than +/- 0.5% ( with 4% engine governing ) Environment Build Up Voltage Operating emperature -40 to +70 C 5 Vac 25 Hz residual volts at power input terminal torage emperature -40 to +85 C elative Humidity Max. 95% oft tart amp ime Vibration Hz 4 seconds +/- 10% Dimensions ypical ystem esponse (L) x (W) x 55.5 (H) mm Less than 20 milliseconds 5.91 (L) x 5.31 (W) x 2.19 (H) inch EMI uppression Weight Internal electromagnetic interference filtering 470 g +/- 2% 1.04 lb +/- 2% 2 ADV-2100M

3 ECI 2 : OULIE / IZE / IALLAI EFEECE AV Wrench Unit : mm Plastic Mounting orque Kgf.cm Figure 1 Outline Drawing AEI 1. AV can be mounted directly on the engine, genset, switchgear, control panel, or any position that will not affect operation. For dimension reference, please see Figure All voltage readings are to be taken with an average-reading voltmeter Meggers and high-potential test equipment must not be used. Use of such equipment could damage the AV. 3. erminal: Fast-On terminals 6.35 mm (1/4 inch). 4. Improper setting of under-frequency protection could cause the output voltage of the unit to drop or become unstable under with changes in load. Avoid making any changes to the U/F setting unless necessary. ECI 3 : DIP WICH POGAMMIG W W2 W1 W1-1 & W1-2 ets the s ensing Voltage W2 W2-1 et ensing for 1 or 3 Phase W2-2 et Frequency W2-3 et Over Excitation Protection or OFF W2-4 & 5 ets Capacity W2-6 ets Capacity of Droop C ADV-2100M 3

4 ECI 4 : ADJUME Figure 2 ECI 5 : WIIG CECI V1 & V2 are ormally Bridged and Voltage is Adjusted on the PBC 1K Ohm 1W C1 et the DIP W Correctly C1 et the DIP W Correctly V1 V1 V2 V2 0 to 10 Vdc Analog lnput Only use when Paralleling to Correct (PF) C is only used when paralleling C. tator Wires C. tator Wires PMG Figure 3 PMG Connection Figure 4 hunt Connection (220V) 4 ADV-2100M

5 C1 et the DIP W Correctly V1 V2 C. (Harmonic) AUX. wires tator Wires Figure 5 Auxiliary Winding (AUX.) Connection AEI 1. All AC voltage readings are average value only. 2. Use a remote 500 ohms 1 watt external V for +/- 5% adjustment range. (keep shorted if not used) 3. Use a remote 1K ohm 1 watt external V for +/- 10% adjustment range. 4. ensing Voltage can be set from Vac Program W1-1 & 2 correctly. 5. For single phase sensing bridge & E3 and move W2-1 to OFF. 6. If your PMG is not working you can also power the AV in shunt using terminals P1 & P2 connected to the output of the generator as long as it s less than 277 Vac. Use only the replacement fuses specified in this user manual. Appearance and specifications of products are subject to change for improvement without prior notice. ADV-2100M 5