Component Identification
|
|
- Ezra Hunter
- 6 years ago
- Views:
Transcription
1 Generic Skills for Microelectronic Engineers Component Identification AIM: To be able to identify common electronic components used in miniature and medium power applications. Methods of labelling, range of values, relevant applications and uses and methods of construction will also be examined. This session is available at Many of the photos in this section are taken from retailers catalogues. Reference is made to the retailer for each photo.
2 Scope We will examine the following components Resistors Capacitors Inductors Transformers Switches Plugs & Sockets Diodes Transistors Special devices
3 Resistors We already know resistors oppose the flow of current like a hose opposes the flow of water. The most obvious parameter that is important about a resistor is its value of resistance. There are however other things that are important. Resistance Tolerance Wattage Voltage rating Construction
4 Resistance and tolerance Resistors are made in specific resistances that repeat every decade. Depending on the tolerance (accuracy with respect to its marked value) there are a different number of values in each decade. These are referred to as the resistor series E12 has 12 values per decade E24 has 24 values per decade etc. The tolerance of the resistor is quoted in percent and tells of the expected variation in value of the resistor. A 10% resistor marked as 100W may actually have a value that varies by 10%. It is clear that there is no point making resistors in the higher E series values if they have a large tolerance. The sizes would overlap.
5
6 The resistance value for most smaller resistors is indicated by coloured bands on the resistor. Some larger resistors have the values stamped on them. (MEMORISE CODE)
7 Wattage The power dissipated in a resistor can be calculated as P = V x I P = I 2 R P =V 2 /R The size of the resistor generally determines how much heat it can dissipate. The common sizes are 0.25W, 0.5W, 1W, 5W, 10W.
8 Voltage rating Typically 0.25W resistors are rated at a working voltage of 250V. The larger sizes usually have a slightly higher rating, ie. 0.5W resistors are typically rated at 350V. For special high voltage applications there are special high voltage resistors available. This is analogous to the pressure applied to a pipe. If you exceed its rated pressure it will burst and the water will flood out. If a resistors voltage is exceed it will breakdown and the electrons will flood out. Usually in an arc!
9 Resistor construction Resistors are manufactured in different ways for different applications. The common types are: Carbon film Metal film Wire wound
10 Carbon film resistors These are a general purpose resistor offering good stability, long life and low noise.
11 Metal film resistors These are a better quality resistor. They offer very good stability, long life and low noise. They can be manufactured to high tolerance. They are therefore usually used to make the higher tolerance resistor series. Both leaded carbon film and metal film resistors are useful up to approximately 500 MHz. At higher frequencies the resistors start to exhibit inductive effects and surface mount resistors are commonly used.
12 Wire wound resistors These resistors are used for high power applications. Because of their wound construction they exhibit high inductance which can be a problem at high frequency. Their ceramic construction allows them to operate at high temperatures.
13 Variable resistors Resistors can also be made so that they can be adjusted by the user. They can be utilized as controls that the user will operate regularly or as adjustments that might be set when the equipment is built then left alone. Rotary Potentiometers Slider potentiometers
14 A potentiometer (pot) is simply a voltage divider that is adjustable. Potentiometers come in many sizes and also come in a number of tapers. The common ones are A B Logarithmic Taper Linear Taper Linear tapers are used for circuits where the output signal is required to change linearly with the movement of the control, ie the voltage from a variable power supply. logarithmic tapers are used for audio equipment where the output should change logarithmically. The human ear receives sound logarithmically, ie double the amplitude does not sound twice as loud. We therefore use A tapers for volume controls etc.
15 Trimpot When the variable resistance will be set during manufacture we usually use screwdriver adjustable potentiometers called trimpots. Many different varieties exist.
16 Capacitors + Capacitors come in a huge range of types. Understanding where they are best used is very important. You will learn more about there construction in other subjects. We will examine: Polyester Monolithic Tantalum Ceramic Electrolytic
17 Polyester (Greencaps) These non-polarised capacitors are good for general purpose applications where small to medium size low cost capacitors are required. Their tolerance is usually 10% and they typically range in size from about 0.001mF to 0.47 mf. (Special ones are available for speaker crossovers up to 10mF) The capacitance value is normally written on the capacitor using the same notation as for resistors except the base unit is pf. 474 = pF = 0.47mF The MKT type (above right) have fixed leg spacing to make circuit board layout more precise. The main usage is for bypass or coupling in low to medium frequency circuits. Different voltage ratings are available (100v, 250v and 630v)
18 Monolithic These non-polarised capacitors have small size for their capacitance value. They are labelled similarly to polyester caps. Size ranges from 0.001mF to 1.0 mf. The main use for these capacitors is for power supply filtering on digital electronic circuit boards, ie computers. Their small size allows less wasted space. They typically have a 10% tolerance and voltage rating of 50V.
19 Tantalum These caps are polarised (they have a +ve and -ve leg). They have very large capacitance for their size. They can only be used in circuits where one leg stays more positive always. (usually marked by +ve sign) Typical range of 0.10mF to 47.0 mf with voltage ratings up to 35V. Applications include power supply filtering or bypassing where a larger capacitance is required. Typical tolerance is 10%.
20 Ceramic Non-polarised capacitors with low values of capacitance, typically 1pF to 0.1mF. Typically 50V rated but higher available (3kV). Tolerance is usually low, 20%, some higher tolerance ones available. Main application is for low capacitance values especially suited to Radio Frequency (RF) circuits or for high voltage applications.
21 Electrolytic These capacitors are the largest valued capacitors available. They range typically from 1.0mF to 10,000mF. They are polarised and have voltage ratings up to around 63V. Some special non-polarised ones are available. They come in axial (RT) or single ended (RB) lead configurations. They must have +ve DC voltage on the +ve leg. The -ve leg is usually marked with arrows. They are typically used as the large filter capacitors in power supplies.
22 TrimCaps Sometimes an adjustable capacitor is required. These are called trimcaps and are usually only available in small sizes 1pF to 100pF. They are normally used to fine tune a capacitor that might be performing a timing or filtering function. Typically found in radio receivers.
23 Inductors Simple chokes are just coils of wire on a former of plastic or iron based material. Large chokes are used in power supplies to stop AC signals but let DC signals pass. Small chokes are used at higher frequencies for the same purpose in radio circuits. they are often mistaken for resistors.
24 Transformers Transformers are used to change the voltage of an AC signal to a new voltage. We commonly use these to change 240V from the mains to a lower voltage suitable to power our circuits. They are made of two coils wound onto the same former.
25 Plugs and Sockets There are hundreds of plugs and connectors in use today. You will learn many over time but should know the following Phono (2.5mm, 3.5mm, 6.5mm) - audio for speakers, mics, headphones etc RCA - line level audio BNC - radio frequency signals, test equipment Banana - general purpose power and low freq signals Crocodile (alligator) - general purpose power and low freq signals testing
26 Diodes Diodes are like valves that only allow electrons to pass in one direction. the current will flow from Anode to Cathode only. The Cathode is marked always with a stripe. They are very often used to turn AC signals into DC signals in power supplies. We often use 4 diodes to do this and they are available in a package called a bridge rectifier especially for this purpose.
27 Light Emitting Diodes Special Light Emitting Diodes (LEDs) used for indicator lights etc. Usually require about 20 ma to run. Available in different physical sizes.
28 Transistors Many thousands of transistors are available for many different applications. At this stage it is important for you to know some of the common packages that transistors are made into. The higher power devices often need to be attached to a heat sink as they get quite hot. These packages have some form of mounting holes etc.
29
30 Special Devices Integrated circuits Voltage Regulators
31 Switches Number of throws (2) Number of poles (3) Switches are classified into their electrical operation and mechanical type. The number of poles, number of throws and whether it is a momentary switch or not is described. A momentary switch does not sit at either throw in the rest position and does not connect to either throw until operated. Eg. A DPDT switch is a double pole double throw switch. Many combinations are available. SPDT, 4PDT, SPST etc.
32 Toggle switch Rocker Switch Slider switches are also available but less common.
33 Fuse Holders To provide protection to the circuitry due to a fault condition we often use fuses. They are wire devices designed to melt when excess current flows through them. This can prevent a fire. Fuse holders are used to hold the fuse.
34 Surface Mount Components With electronic circuits needing to become much smaller and frequencies of operation becoming much higher we see a lot of surface mount design being done.
Workshop Part Identification Lecture N I A G A R A C O L L E G E T E C H N O L O G Y D E P T.
Workshop Part Identification Lecture N I A G A R A C O L L E G E T E C H N O L O G Y D E P T. Identifying Resistors Resistors can be either fixed or variable. The variable kind are called potentiometers
More informationTechnician Licensing Class T6
Technician Licensing Class T6 Amateur Radio Course Monroe EMS Building Monroe, Utah January 11/18, 2014 January 22, 2014 Testing Session Valid dates: July 1, 2010 June 30, 2014 Amateur Radio Technician
More informationMatrix Multimedia Limited Tel Fax
matrix multimedia Electronic Circuits and Components v2.0 Course material with Virtual Laboratories that stimulate, teach & test. This second version of Electronic Circuits and Components is bigger and
More informationUniversity of Technology, Jamaica School of Engineering. Electrical Workshop Notes On Electrical components
University of Technology, Jamaica School of Engineering Electrical Workshop Notes On Electrical components Resistors Resistors are fundamental components in electronic circuits. A resistor is constructed
More informationT6A4. Electrical components; fixed and variable resistors, capacitors, and inductors; fuses, switches, batteries
Amateur Radio Technician Class Element Course Presentation ti ELEMENT SUB-ELEMENTS Technician Licensing Class Supplement T Electrical/Electronic Components Exam Questions, Groups T - FCC Rules, descriptions
More information10 2 2,13,15,16,46 27, non-inductive ,26,
HANDS-ON RADIO PARTS LIST (Thanks, John AF4WM and Steve AD7KR) Updated through Experiment 129 Quantities assume all parts available for re-use MAX QTY EXPERIMENT NOTES 1/4 WATT RESISTOR (All values are
More informationContents. 1. Essential Electronics 1. Preface Acknowledgements
Contents Preface Acknowledgements ix xi 1. Essential Electronics 1 1.1: Current 2 1.2: Voltage 5 1.3: Power 6 1.4: Signals and Averages 7 1.4.1: Mean Average 7 1.4.2: Rectified Average 8 1.4.3: RMS Average
More informationWhat is a Resistor? Token Electronics Industry Co., Ltd. Version: January 12, Web:
Version: January 12, 2017 What is a Resistor? Web: www.token.com.tw Email: rfq@token.com.tw Token Electronics Industry Co., Ltd. Taiwan: No.137, Sec. 1, Zhongxing Rd., Wugu District, New Taipei City, Taiwan,
More informationThe 6LE8 One Tube Broadcaster
The 6LE8 One Tube Broadcaster Introduction The purpose of this broadcaster is to transmit your favorite music to every AM radio in your home. The transmitting power is so low that it should not bother
More information5W Mono Amplifier Kit
5W Mono Amplifier Kit Kit Construction Before you start assembling your kit there are a couple of important things you must do. FIRST read through these instructions entirely before you start construction
More informationElectronic Components. Identification of components and handling precautions to protect them from damage due to electrostatic discharge
Electronic Components Identification of components and handling precautions to protect them from damage due to electrostatic discharge 1 Passive Components Resistors Capacitors Inductors Diodes Interface
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More informationSUBELEMENT T6 Electrical components: semiconductors; circuit diagrams; component functions 4 Exam Questions - 4 Groups
SUBELEMENT T6 Electrical components: semiconductors; circuit diagrams; component functions 4 Exam Questions - 4 Groups 1 T6A Electrical components: fixed and variable resistors; capacitors and inductors;
More informationDepartment of Electronics & Telecommunication.
BASIC ELECTRONICS ENGINEERING 1 Department of Electronics & Telecommunication. Experiment No. : 01 Date of Performance: ----------------- Name of the student: ---------------------------------------------------------------------------------------------
More informationLM2412 Monolithic Triple 2.8 ns CRT Driver
Monolithic Triple 2.8 ns CRT Driver General Description The is an integrated high voltage CRT driver circuit designed for use in high resolution color monitor applications. The IC contains three high input
More informationModel SR554 Transformer Preamplifier
Model SR554 Transformer Preamplifier Model SR554 Transformer Preamplifier 1290-D Reamwood Avenue Sunnyvale, California 94089 Phone: (408) 744-9040 Fax: (408) 744-9049 email: info@thinksrs.com www.thinksrs.com
More informationWeener Wah FX TYPE: Wah Wah Based on the Clyde McCoy 2016 edition madbeanpedals
Weener Wah FX TYPE: Wah Wah Based on the Clyde McCoy 2016 edition madbeanpedals 1.95 W x 2.275 H Terms of Use: You are free to use purchased WeenerWah circuit boards for both DIY and small commercial operations.
More informationWiring Manual NEScaf April 2010 (August 2006)
Wiring Manual NEScaf April 2010 (August 2006) Switched Capacitor Audio Filter The NEScaf is a switched capacitor audio filter (acronym SCAF) built around a building-block type filter chip. The NEScaf will
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationPart Derating Parameters
Part Derating Parameters Capacitors Fixed Aluminum (Electrolytic) Fixed Ceramic Fixed Mica/Glass Fixed Paper/Plastic Fixed Tantalum (Non- Solid) Reverse Voltage Fixed Tantalum (Solid) Reverse Voltage Variable
More informationThe Walford Electronics Ford Receiver Kit Project Construction Manual
The Walford Electronics Ford Receiver Kit Project Construction Manual Walford Electronics Ford Receiver construction manual V1.5 Page 1 of 22 Introduction The Ford receiver has four stages: The first stage
More informationCustom Integrated Circuit (MSM9520RS) Replacement Module
FT-101Z/ FT-107/ FT-707/ FT-901,902 (later version) DISPLAY COUNTER UNIT (PB-2086A) Custom Integrated Circuit (MSM9520RS) Replacement Module Assembly and Installation Manual (v1.3e) STEP-BY-STEP PROCEDURES
More informationName My end of year 8 Target = Teacher. OLSJ Design & Technology Electronic Products. Overall Progress Effort Rating ABCDEFG.
Name My end of year 8 Target = Teacher OLSJ Design & Technology Electronic Products Week 1 2 3 4 5 6 7 Lesson Objectives What will you learn about today? 1. Circuit Symbols and circuit diagram 2. Drilling
More information12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
More informationPhysics 310 Lab 2 Circuit Transients and Oscilloscopes
Physics 310 Lab 2 Circuit Transients and Oscilloscopes Equipment: function generator, oscilloscope, two BNC cables, BNC T connector, BNC banana adapter, breadboards, wire packs, some banana cables, three
More informationHAMTRONICS TB901 FM EXCITER INSTALLATION, OPERATION, & MAINTENANCE
HAMTRONICS TB901 FM EXCITER INSTALLATION, OPERATION, & MAINTENANCE GENERAL INFORMATION. The TB901 is a single-channel low power fm transmitter (exciter) designed to provide 300-600 milliwatts continuous
More informationRadio Merit Badge Boy Scouts of America
Radio Merit Badge Boy Scouts of America Module 2 Electronics, Safety & Careers BSA National Radio Scouting Committee2012 Class Format Three modules any order Module 1 Intro To Radio Module 2 Electronic
More informationA 100-Watt Transmitter Using a Pair of VT1625s
12/16/2007 6:00 PM VT1625 100 Watt Transmitter A 100-Watt Transmitter Using a Pair of VT1625s FIG. 10.6 A 100-watt transmitter for five bands, using salvaged TV power transformer and surplus 1625 amplifier
More informationHow To Make A Basic DC Controller For Model Trains.
How To Make A Basic DC Controller For Model Trains. By John Rumming. Welcome to another of my PDF how to documents. This one will cover a topic of a basic DC controller. There are a minimal amount of parts,
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationAmplifier, Product Design
Amplifier, Product Design Choose one component from the amplifier circuit and investigate technical, theory and mathematical information related to your chosen component. This work will be completed over
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationUltra 4B SE Special Edition. Stereo Phono/Line Preamplifier
Modular Series Ultra B SE Special Edition Stereo Phono/Line Preamplifier User s Manual Phono Line Line Balance Volume Mapletree Audio Design Ultra B SE Stereo Preamplifier Rev. Feb. / Mapletree Audio Design
More informationEmbedded Control. Week 1 (6/29/11)
Embedded Control Week 1 (6/29/11) Week 1 15:00 Lecture Circuit theory, terminology Overview of elementary circuit components Reading circuit diagrams 16:00 Lab NXT GPIO with HiTechnic sensor expansion
More information1 FUNCTIONAL DESCRIPTION WAY SPLITTER/INPUT BOARD FET RF AMPLIFIERS WAY POWER COMBINER VSWR CONTROL BOARD...
CONTENTS 1 FUNCTIONAL DESCRIPTION...1 2 4-WAY SPLITTER/INPUT BOARD...2 3 FET RF AMPLIFIERS...3 4 4-WAY POWER COMBINER...4 5 VSWR CONTROL BOARD...5 6 ADJUSTMENT OF BIAS VOLTAGE TO ESTABLISH PROPER QUIESCENT
More informationUNIT V - RECTIFIERS AND POWER SUPPLIES
UNIT V - RECTIFIERS AND POWER SUPPLIES OBJECTIVE On the completion of this unit the student will understand CLASSIFICATION OF POWER SUPPLY HALF WAVE, FULL WAVE, BRIDGE RECTIFER AND ITS RIPPLE FACTOR C,
More information4/30/2012. General Class Element 3 Course Presentation. Circuit CoCircuit Componentsmponents. Subelement G6. 3 Exam Questions, 3 Groups
General Class Element 3 Course Presentation ti ELEMENT 3 SUB ELEMENTS General Licensing Class Subelement G6 Circuit Components 3 Exam Questions, 3 Groups G1 Commission s Rules G2 Operating Procedures G3
More informationGRID CONTROLLED POWER SUPPLY IS A VERSATILE UNIT Uses Pair of RCA-2050 s for Wide Voltage Range
10/30/07 11:55 PM Thyratrons GRID CONTROLLED POWER SUPPLY IS A VERSATILE UNIT Uses Pair of RCA-2050 s for Wide Voltage Range By J. H. OWENS, W2FTW and G. D. HANCHETT, W1AK/2 RCA Ham Tips Volume 6, Number
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationElectric Druid Flangelicious Flanger Project
Electric Druid Flangelicious Flanger Project (Using either 4KNOBFLANGE or MULTIFLANGE chips) Overview! 2 Build Instructions! 2 Populate the PCB! 2 1N4148 Diodes! 2 Resistors! 2 Cup of tea and soldering
More informationExperiment no -1: Components Testing *
OpenStax-CNX module: m50547 1 Experiment no -1: Components Testing * Bijay_Kumar Sharma This work is produced by OpenStax-CNX and licensed under the Creative Commons Attribution License 4.0 Abstract This
More informationDEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 03. Resistors
MEHRAN UNIVERSITY OF ENGINEERING AND TECHNOLOGY, JAMSHORO DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 03 Resistors Roll. No: Checked by: Date: Grade: Object: To become familiar with resistors,
More informationBYOC Vibrato Kit Instructions BA662A version
BYOC Vibrato Kit Instructions BA662A version Please read these instructions very thoroughly before building even if you are an experience builder. Because of the layout, there is a certain order which
More informationBYOC Vibrato Kit Instructions BA6110 version
BYOC Vibrato Kit Instructions BA6110 version Please read these instructions very thoroughly before building even if you are an experience builder. Because of the
More informationHome Map Projects Construction Soldering Study Components 555 Symbols FAQ Links
Home Map Projects Construction Soldering Study Components 555 Symbols FAQ Links Circuit Symbols Wires Supplies Output devices Switches Resistors Capacitors Diodes Transistors Audio & Radio Meters Sensors
More informationBASIC ELECTRONICS PROF. T.S. NATARAJAN DEPT OF PHYSICS IIT MADRAS LECTURE-2 ELECTRONIC DEVICES -1 RESISTOR, IDEAL SOURCE VOLTAGE & CAPACITOR
BASIC ELECTRONICS PROF. T.S. NATARAJAN DEPT OF PHYSICS IIT MADRAS LECTURE-2 ELECTRONIC DEVICES -1 RESISTOR, IDEAL SOURCE VOLTAGE & CAPACITOR In the last lecture we saw the importance of learning about
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationIPR LA-3 KIT last update 15 march 06
IPR LA-3 KIT last update 15 march 06 PART-2: Audio Circuitry CIRCUIT BOARD LAYOUT: Power and Ground Distribution Now that your power supply is functional, it s time to think about how that power will be
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationAM RADIO KIT MODEL AM-780K. Assembly and Instruction Manual
AM RADIO KIT MODEL AM-780K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2007, 1999 by Elenco Electronics, Inc. All rights reserved. Revised 2007 REV-F 753108 No part of this book
More informationElectronic component
Electronic component Electronic component: An electronic component is any basic discrete device or physical entity in an electronic system used to affect electrons or their associated fields. 2 TYPES OF
More informationNRI INSTITUTE OF TECHNOLOGY
NRI INSTITUTE OF TECHNOLOGY (Approved by AICTE, New Delhi: Affiliated to JNTUK, Kakinada) POTHAVARAPPADU (V), (via) Nunna, Agiripalli (M), Krishna District, A.P. PIN: 521212 Ph: 08656-324999 Website: nrigroupofcolleges.com
More informationElectricity Fundamentals Training System
Electricity Fundamentals Training System LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 07/2018 Table of Contents General Description 2 Courseware 2 Topic Coverage 2 List of Available Training
More informationLM V Monolithic Triple Channel 15 MHz CRT DTV Driver
220V Monolithic Triple Channel 15 MHz CRT DTV Driver General Description The is a triple channel high voltage CRT driver circuit designed for use in DTV applications. The IC contains three high input impedance,
More informationLM2462 Monolithic Triple 3 ns CRT Driver
LM2462 Monolithic Triple 3 ns CRT Driver General Description The LM2462 is an integrated high voltage CRT driver circuit designed for use in color monitor applications. The IC contains three high input
More informationUNSIGNED HARDCOPY NOT CONTROLLED. REFERENCES MS90178 Standard 24-Value Series Decade for Electronic Components of 5-, 10-, and 20-Percent Tolerance
Subject: APPROVED BY STATUS PURPOSE AFFECTED FUNCTIONS Electrical Component Identification Manager, Hardware Engineering Maintenance Revision Defines and explains the techniques used for identifying the
More informationFCC Technician License Course
FCC Technician License Course 2014-2018 FCC Element 2 Technician Class Question Pool Presented by: Tamiami Amateur Radio Club (TARC) WELCOME To the SECOND of 4, 3-hour classes presented by TARC to prepare
More informationHendricks QRP Kits The Twofer Rev
Hendricks QRP Kits The Twofer Rev 1 11-15-06 1. Description The Twofer is a classic QRP transmitter that s easy to assemble and operate. It uses a JFET VXO (variable crystal oscillator), driver stage and
More informationWESTREX RA-1712 PHOTOGRAPHIC SOUND RECORD ELECTRONICS
INTRODUCTION The RA-1712 solid state Record Electronics is an integrated system for recording photographic sound tracks on a Westrex photographic sound recorder. It accepts a 600Ω input signal level from
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationUltimatum Fuzz. The Ultimate experience in vintage-style octave-up fuzz
Ultimatum Fuzz The Ultimate experience in vintage-style octave-up fuzz Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationIntro to Electronics. Week 1
Intro to Electronics Week 1 1 What is included? DIY ELECTRONICS 2 Lights http://www.flickr.com/photos/oskay/3423822454/ Intro to Electronics, Week 1 Last modified April 16, 2012 3 Sounds http://www.flickr.com/photos/createdigitalmedia/3701158293/
More informationINSPIRE VLF-3 Rev #1C Receiver Kit ASSEMBLY INSTRUCTIONS
INSPIRE VLF-3 Rev #1C Receiver Kit ASSEMBLY INSTRUCTIONS The following assembly instructions should be followed carefully. The INSPIRE VLF-3 receiver kit is NOT a simple electronic assembly. If you follow
More informationLM2405 Monolithic Triple 7 ns CRT Driver
LM2405 Monolithic Triple 7 ns CRT Driver General Description The LM2405 is an integrated high voltage CRT driver circuit designed for use in color monitor applications The IC contains three high input
More informationTS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 2 BASIC CIRCUIT ELEMENTS OBJECTIVES The purpose of this experiment is to familiarize the student with
More informationTektronix 485 repair
Tektronix 485 repair Fig. 1 Tektronix 485. 2 channel, 350MHz oscilloscope. Some time ago my colleague gave me a faulty TEK 485 oscilloscope. Symptoms: Bright, blue mains fuse explosion after pressing the
More informationAn Electronic Variable Load by Dave Chute, KG4BZW
EDITOR: GEOFF HAINES, N1GY Published Quarterly N1GY@ARRL.NET Summer Edition FROM THE EDITOR: Once again I am happy to report that we have several great articles in the Summer Edition of The WCF Experimenter.
More informationDIGITAL / ANALOG TRAINER
DIGITAL / ANALOG TRAINER MODEL XK-150 A COMPLETE MINI-LAB FOR BUILDING, TESTING AND PROTOTYPING ANALOG AND DIGITAL CIRCUITS Instruction Manual ELENCO Copyright 2016, 1998 by ELENCO Electronics, Inc. All
More informationMDT DSB TRANSCEIVER CONSTRUCTION MANUAL. MDT Construction Manual Issue 2 Page 1
MDT DSB TRANSCEIVER CONSTRUCTION MANUAL MDT Construction Manual Issue 2 Page 1 CONTENTS 1 Introduction... 4 2 DSB vs SSB... 5 3 DSB transmitter... 6 4 Direct Conversion receiver... 7 5 MDT Block Diagram...
More informationElectric Druid 4 second Digital Delay Project
Electric Druid 4 second Digital Delay Project Overview! 2 Build Instructions! 2 Populate the PCB! 2 Resistors! 2 Cup of tea and soldering check! 3 Power protection diode! 4 Ground link wire! 4 IC sockets!
More informationThe Uniden Grant XL Owners Site
The Uniden Grant XL Owners Site Modifications page for the Grant XL (For Informational purposes only) The author of this site takes NO responsibility for illegal modifications and/or use of illegally modified
More informationValue Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
More informationUK-electronic 2012/15 Manual for the Tap Tremolo Rev. 2.0 Based on TAPLFO from Tom Wiltshire (www.electricdruid.com)
UK-electronic 2012/15 Manual for the Tap Tremolo Rev. 2.0 Based on TAPLFO from Tom Wiltshire (www.electricdruid.com) Page 1..2...Basics Page 3...short Circuit description Page 4...Bill of material Page
More informationAUTO-SCAN FM RADIO KIT
FM-88K 071210.qxp_FM-88K 060810 12/29/15 10:05 AM Page 1 AUTO-SCAN FM RADIO KIT MODEL FM-88K Assembly and Instruction Manual ELENCO Copyright 2016, 2011 by ELENCO All rights reserved. No part of this book
More informationBi-Directional DC Motor Speed Controller 5-32Vdc (3166v2)
General Guidelines for Electronic Kits and Assembled Modules Thank you for choosing one of our products. Please take some time to carefully read the important information below concerning use of this product.
More informationCircuit Board Assembly Instructions
Circuit Board Assembly Instructions This document walk you through the assembly of the Base4 Clock v1.2 - v1.3 circuit boards. Important note for kit buyers The color and appearance of the components may
More information5. The Different Types of Resistors
5. The Different Types of Resistors Resistors ( R ), are the most fundamental and commonly used of all the electronic components, to the point where they are almost taken for granted. There are many different
More informationHigh Voltage Supply. 330 V from 12 V. For the Valved RIAA Preamplifier and other applications POWERSUPPLY
For the Valved RIAA Preamplifier and other applications High Voltage Supply 33 V from 12 V Design by T. Giesberts Although this supply was primarily designed for use with the Valved RIAA Preamplifier,
More informationA Novel Design and Application of Binary Resistance Box Using DIP Switches
RESEARCH ARTICLE OPEN ACCESS A Novel Design and Application of Binary Resistance Box Using DIP Switches 1 A.Anvesh, 2 T.Charan Singh, 3 M.Maheswara Rao 1 2,3 Swarna Bharathi Institute of Science & Technology,
More informationTRACE ELLIOT SERVICE MANUAL NO. SM00025 ISSUE 1
TRACE ELLIOT SERVICE MANUAL NO. SM00025 ISSUE 1 Date: January 6, 1997 Product Code : T3455/3456 Model No : Velocette 12R / Alnico Technical File No : TE00025 Issued by: Trace Elliot Limited. Blackwater
More informationFM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Build Instructions Before you start, take
More informationSTUDENT NUMBER Letter VCE VET ELECTRONICS. Written examination. Monday 31 October 2005
Victorian CertiÞcate of Education 2005 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Figures Words STUDENT NUMBER Letter VCE VET ELECTRONICS Written examination Monday 31 October 2005 Reading time: 9.00 am
More informationSUPER Tuna ][+ Builder s Guide
SUPER Tuna ][+ Builder s Guide Ver2.3 Rex Harper W1REX 3/25/2015 The first thing you should do is to familiarize yourself with what you are going to build. The previous 3 pages are schematics of the
More informationXkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ Rev 1.15 An Optional accessory for the Xkitz XLO-5 or XLO-5DC 5 Channel Color Light Organs Introduction This kit contains all the electronics
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationMono Amplifier. LM386 Headphone Amp
Mono Amplifier LM386 Headphone Amp Layout On/Off Switch - cuts power to the circuit Mono Input Jack: use either L or R or solder together Schematic Step 1 - Parts List 1.) R1-10ohm Resistor - Brown Black
More informationIntroduction. Inductors in AC Circuits.
Module 3 AC Theory What you ll learn in Module 3. Section 3.1 Electromagnetic Induction. Magnetic Fields around Conductors. The Solenoid. Section 3.2 Inductance & Back e.m.f. The Unit of Inductance. Factors
More informationLesson 3: Electronics & Circuits
Lesson 3: Electronics & Circuits Preparation for Amateur Radio Technician Class Exam Topics Review Ohm s Law Energy & Power Circuits Inductors & Inductance Capacitors & Capacitance Analog vs Digital Exam
More informationTen Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
More informationInstant MTBF Data Input Sheet Commercial / Bellcore TR Integrated Circuits, Bipolar, Digital
Instant MTBF Data Input Sheet Commercial / Bellcore TR-332 Probabilistic Software, Inc. http://www.e-mtbf.com System / Equipment Name: Assembly Name: Quantity Of This Assembly: Parts List Number: Environment:
More informationMST3 SSB TRANSCEIVER BOARD KIT CONSTRUCTION AND OPERATION MANUAL. MST3 Construction and Operation Manual Issue 1 Page 1
MST3 SSB TRANSCEIVER BOARD KIT CONSTRUCTION AND OPERATION MANUAL MST3 Construction and Operation Manual Issue 1 Page 1 CONTENTS 1 Introduction... 5 2 Block Diagram... 7 3 Circuit Description... 8 3.1 Carrier
More informationSPECIFICATIONS: Subcarrier Frequency 5.5MHz adjustable, FM Modulated +/- 50KHz. 2nd 11MHz >40dB down from 5.5MHz
Mini-kits AUDIO / SUBCARRIER KIT EME75 Version4 SPECIFICATIONS: Subcarrier Frequency 5.5MHz adjustable, FM Modulated +/- 50KHz Subcarrier Output 1.5v p-p Output @ 5.5MHz DESCRIPTION & FEATURES: The Notes
More informationMetal Detector. Student Lab Guide. Engineering Teaching Laboratory. Lab Partner(s)
Metal Detector Student Lab Guide Engineering Teaching Laboratory Name Date Lab Partner(s) NEW TERMS Electric Circuit: Electric circuits are paths for transmitting electric current, or moving electricity.
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationSystems Engineering. Passive Components. v1.2 March itic.
Systems Engineering Passive Components Pere Palà itic http://itic.cat v1.2 March 2012 Resistors Resistor Types Resistors Ubiquitous Uncritical Surface mount chip Metal film Carbon Wirewound Precision resistors
More informationDRTXM2 TRANSMITTER BILL OF MATERIAL IDENT QTY PART NUMBER DESCRIPTION
DRTXM2 TRANSMITTER BILL OF MATERIAL H1 C1-5,7,10-11,15,17-18,20, 22-28,34,38, 43-46,49-53,1A,2A 8 Right Angle LED Mount 0 0.01uf 50V Ceramic Disc Capacitor 31 0.1 UF/50V Decoupling Capacitors C13,14,39-42
More informationBlue Ring Tester Kit Assembly & User Manual
Blue Ring Tester Kit Assembly & User Manual Alltronics LLC/AnaTek Instruments 2761 Scott Blvd, Santa Clara, CA, 95050, USA March 2015 Edition Tel: 408-778-3868, Fax: 408-778-2558, E mail : tech@alltronics.com
More information