MHz FUNCTION GENERATOR INSTRUCTION MANUAL

Size: px
Start display at page:

Download "MHz FUNCTION GENERATOR INSTRUCTION MANUAL"

Transcription

1 MHz FUNCTION GENERATOR INSTRUCTION MANUAL

2 Table of Contents Introduction 2 Specification 2 EMC 5 Safety 4 Installation 5 Operation 7 Maintenance 8 1

3 Introduction This instrument is a 20MHz function generator with waveforms of sine, square, triangle, ramp, pulse and DC from a variable amplitude 50Ω output. A TTL output is also provided. The frequency range is 0.2Hz to 20MHz selected by an eight decade range multiplier and calibrated vernier. The sweep input can be used to give a >20:1 frequency change within a selected range. The generator output level is 20Vpk-pk maximum from a 50Ω source. The level is set via switched attenuators plus vernier with a total range of 66dB. DC offset is vernier adjustable over a ±10V range with 0V defined by a centre detent. A switchable symmetry control with a 6:1 range permits ramp and pulse waveforms to be produced. Specification FREQUENCY Frequency Range: Vernier Range: Vernier Accuracy: 0.2Hz to 20MHz in 8 overlapping decade ranges with fine adjustment by a vernier. >10:1 on each range. Typically ± 5% of full scale. SWEEP MODE (EXTERNAL) Sweep Range: Typically >20:1. Input Impedance: 82 kω Input Sensitivity: Typically 0 to 2V for 10:1 sweep. Maximum Allowable Input Voltage: ± 10V Maximum Slew Rate of sweep voltage: 0.1V/us OPERATING MODES (Specifications apply for the top decade of each frequency range and output 10V peak-to-peak into 50Ω termination). Sine Distortion: Amplitude Flatness: Triangle Linearity: Squarewave Rise and Fall Times: DC Range: Symmetry Symmetry Range: Typically 2% on 200, 2k and 20k ranges. ± 0.2dB to 200kHz; ± 2dB to 20MHz. Typically 99% on khz ranges. <22ns ±10V from 50Ω Typically variable from 1:6 to 6:1 up to 500kHz. 2

4 OUTPUTS 50Ω TTL GENERAL Three switch-selectable ranges with 26dB vernier control within each attenuator range. 0dB Range: 1V to 20V peak-to peak from 50Ω (0.5V to 10V into 50Ω). 20dB Range: 100mV to 2V peak-to-peak (50mV to 1V into 50Ω) 40dB Range: 10mV to 0.2V peak-to-peak (5mV to 0.1V into 50Ω) DC Offset Control Range: ±10V from 50Ω. DC offset plus signal peak limited to ±10V (± 5V into 50Ω). DC offset plus waveform attenuated proportionally in 20dB and 40dB position. Capable of driving 4 standard TTL loads. Power: Operating Range: Storage Range: 230V or 115V nominal 50/60Hz, adjustable internally; operating range ±14% of nominal; 30VA max. Installation Category II. + 5ºC to +40ºC, 20% to 80% RH. 40ºC to +70ºC Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2. Electrical Safety: Complies with IEC EMC: Size: Weight: Complies with EN and EN (W) x 82(H) x 230(D) mm, (10.3 x 3.4 x 9.2 ) excluding feet. 1.5 kg (3.3lb). 3

5 Safety This instrument is Safety Class I according to IEC classification and has been designed to meet the requirements of IEC (Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use). It is an Installation Category II instrument intended for operation from a normal single phase supply. This instrument has been tested in accordance with IEC and has been supplied in a safe condition. This instruction manual contains some information and warnings which have to be followed by the user to ensure safe operation and to retain the instrument in a safe condition. This instrument has been designed for indoor use in a Pollution Degree 2 environment in the temperature range 5 C to 40 C, 20% - 80% RH (non-condensing). It may occasionally be subjected to temperatures between +5 C and 10 C without degradation of its safety. Do not operate while condensation is present. Use of this instrument in a manner not specified by these instructions may impair the safety protection provided. Do not operate the instrument outside its rated supply voltages or environmental range. WARNING! THIS INSTRUMENT MUST BE EARTHED Any interruption of the mains earth conductor inside or outside the instrument will make the instrument dangerous. Intentional interruption is prohibited. The protective action must not be negated by the use of an extension cord without a protective conductor. When the instrument is connected to its supply, terminals may be live and opening the covers or removal of parts (except those to which access can be gained by hand) is likely to expose live parts. The apparatus shall be disconnected from all voltage sources before it is opened for any adjustment, replacement, maintenance or repair. Any adjustment, maintenance and repair of the opened instrument under voltage shall be avoided as far as possible and, if inevitable, shall be carried out only by a skilled person who is aware of the hazard involved. If the instrument is clearly defective, has been subject to mechanical damage, excessive moisture or chemical corrosion the safety protection may be impaired and the apparatus should be withdrawn from use and returned for checking and repair. Make sure that only fuses with the required rated current and of the specified type are used for replacement. The use of makeshift fuses and the short-circuiting of fuse holders is prohibited. Do not wet the instrument when cleaning it. The following symbols are used on the instrument and in this manual:- Caution -refer to the accompanying documentation, incorrect operation may damage the instrument. terminal connected to chassis ground. mains supply OFF. l mains supply ON. alternating current. 4

6 Emissions Immunity Cautions This function generator has been designed to meet the requirements of the European EMC Directive 89/336/EEC. Compliance was demonstrated by meeting the test limits of the following standards: EN (1992) Generic emission standard for residential commercial and light industry. Test methods and limits used were: a) EN55022 Conducted, Class B b) EN55022 Radiated, Class B EN (1992) Generic immunity standard for residential, commercial and light industry. Test methods and limits used were: a) EN (1993) Electrostatic Discharge, 8 kv air discharge. b) IEC801-3 (1984) RF Field, 3 V/m. c) IEC801-4 (1988) Fast Transient, 1 kv peak (AC line), 0.5kV peak (signal lines). To ensure continued compliance with the EMC directive the following precautions should be observed: a) connect the generator to other equipment using only high quality, double-screened cables. b) after opening the case for any reason ensure that all signal and ground connections are remade correctly before replacing the covers. Always ensure all case screws are correctly refitted and tightened. c) In the event of part replacement becoming necessary, only use components of an identical type, see the Service Manual. EMC 5

7 Installation Mains Operating Voltage The operating voltage of the instrument is shown on the rear panel. Should it be necessary to change the operating voltage from 230V to 115V or vice-versa, proceed as follows: 1. Disconnect the instrument from all voltage sources. 2. Remove the 4 screws which hold the upper and lower case halves together and lift off the case upper. 3. Change the transformer connections following the diagrams below. 230V Operation - Primaries in series 115V Operation - Primaries in parallel Mains Lead 4. Reassemble in the reverse order. 5. To comply with safety standard requirements the operating voltage marked on the rear panel must be changed to clearly show the new voltage setting. WARNING! THIS INSTRUMENT MUST BE EARTHED Any interruption of the mains earth conductor inside or outside the instrument will make the instrument dangerous. Intentional interruption is prohibited. 6

8 Operation Power The ON/OFF switch is on the rear panel of the instrument. Frequency Selection Symmetry Frequency range is selected by an eight position multiplier switch with fine adjustment by calibrated vernier. A slide switch selects the symmetry control which varies the duty cycle 1:6 to 6:1 to produce sawtooth and variable pulse-width waveforms. Note: The symmetry of the Aux Output does not vary when Sine or Triangle are selected because the Aux Output is generated by a zero crossing comparator. Function Selection The output waveform shape is selected by a four position switch to give sine, square, triangle and DC. A DC level only is useful as it permits input threshold testing of a circuit without having to connect up an external supply. Main Output DC Offset Aux Output The amplitude of the 50Ω MAIN output is controlled by the 3-position ATTENUATOR switches and AMPLITUDE control. Maximum output is 20 volts peak-to-peak from 50Ω and 10 volts peakto-peak when terminated with a 50Ω load. The AMPLITUDE control has greater than 26dB range and used in conjunction with the ATTENTUATORS a range of 0dB to 66dB can be achieved. This provides a range of 20V peakto-peak down to 10mV peak-to-peak, or 10V peak-to-peak down to 5mV peak-to-peak into 50Ω. Greater attenuation can be achieved by using standard 50Ω BNC attenuators. To maintain waveform integrity only 50Ω cable should be used and the receiving end should be terminated with a 50Ω load. The 50Ω MAIN output will withstand a short circuit for a period of 2 minutes at maximum output and greater periods at lower output levels. Do not apply external voltages to this output. The DC OFFSET control has a range of ±10 volts from 50Ω in all output modes; the control has a centre detent for 0 volts. DC offset plus signal peak is limited to ± 10V (± 5V into 50Ω). DC offset plus waveform is attenuated proportionally in the 20dB and 40dB positions. The AUX output provides a fixed TTL pulse output at the same frequency and phase as the 50Ω MAIN output and is capable of driving 4 standard TTL loads. Sweep Input The generator frequency can be swept, DC programmed or modulated by a suitable control voltage applied to the SWEEP IN socket. The instrument sums the SWEEP IN voltage with the internal control voltage derived from the FREQUENCY vernier to determine the operating frequency. A positive voltage increases the frequency; for frequency control with positive-going DC inputs the vernier should therefore be set to the lower frequency limit of the range to be swept. For example, a 0V to +2V signal will sweep the generator 1 decade up from range minimum, set by the vernier, to range maximum. 7

9 Similarly, a negative voltage decreases the frequency and for negative-going DC inputs the vernier should be set to the upper frequency limit of the range to be swept. For example, a 0V to 2V signal will sweep the generator 1 decade down from range maximum, set by the vernier, to range minimum. To use a sweep signal which is symmetrical about ground, the vernier should be set to give a frequency at approximately the centre of the band to be swept. Do not apply external voltages exceeding ±10V. Cleaning Mains Fuse Maintenance For service repair and calibration please contact your local Tenma distributor or go to If the instrument requires cleaning use a cloth that is only lightly dampened with water or a mild detergent. WARNING! TO AVOID ELECTRIC SHOCK, OR DAMAGE TO THE INSTRUMENT, NEVER ALLOW WATER TO GET INSIDE THE CASE. TO AVOID DAMAGE TO THE CASE NEVER CLEAN WITH SOLVENTS. The transformer primary is protected by an integral thermal fuse which is not user replaceable. Should a fault develop which causes the thermal fuse to blow, the generator must be returned to the manufacturer or agent for service. 8

10 TEST EQUIPMENT 405 Pioneer Blvd. Springboro, Ohio Book Part No Issue 1

EC Declaration of Conformity

EC Declaration of Conformity EC Declaration of Conformity TABLE OF CONTENTS 1. SAFETY SUMMARY.. 1 2. INTRODUCTION 5 3. SPECIFICATION 7 EN 61326-1: Electrical equipment for measurement, control and laboratory use EMC requirements (1997+A1:

More information

TG MHz Function Generator Service Manual

TG MHz Function Generator Service Manual TG120 20 MHz Function Generator Service Manual Book Part Number 48591-0520 Issue 1 Table of Contents Specification 1 Safety 3 Installation 4 General 5 Circuit Descriptions 6 Calibration 7 Parts List 8

More information

TG MHz DDS Function Generator INSTRUCTION MANUAL

TG MHz DDS Function Generator INSTRUCTION MANUAL TG1006 10MHz DDS Function Generator INSTRUCTION MANUAL Table of Contents Specifications 2 EMC 6 Safety 7 Installation 8 Connections 9 General 10 Standard Waveform Operation 11 Sweep 13 FSK 15 Store and

More information

TG550 AIM & THURLBY THANDAR INSTRUMENTS. 5MHz function generator with sweep

TG550 AIM & THURLBY THANDAR INSTRUMENTS. 5MHz function generator with sweep AIM & THURLBY THANDAR INSTRUMENTS TG550 5MHz function generator with sweep simultaneous display of frequency & amplitude crystal controlled digital frequency locking seven digit external frequency counter

More information

W DC ELECTRONIC LOAD INSTRUCTION MANUAL

W DC ELECTRONIC LOAD INSTRUCTION MANUAL 72-7855 300W DC ELECTRONIC LOAD INSTRUCTION MANUAL Table of Contents Introduction 1 Specification 2 EMC 6 Safety 7 Installation 8 Connections 9 Operating Controls 11 Operation 14 Application Notes 20 Remote

More information

CIRCUIT-TEST ELECTRONICS

CIRCUIT-TEST ELECTRONICS USER'S MANUAL Sweep Function Generator with Counter SWF-8030 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY INFORMATION...page 3 INTRODUCTION... 4 SPECIFICATIONS... 5 FRONT PANEL

More information

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: MODEL: Multimeter Service Information

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: MODEL: Multimeter Service Information IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-340 MODEL: 61-342 Multimeter Service Information The Service Information provides the following information: Precautions and safety information Specifications

More information

8120 FUNCTION GENERATOR Operation Manual

8120 FUNCTION GENERATOR Operation Manual 8120 FUNCTION GENERATOR Operation Manual Copyright Copyright 1996 by this company. All rights reserved. No part of this publication may be reproduced in any form or by any means without the written permission

More information

8110 FUNCTION GENERATOR. Safety Instruction. Safety Symbols

8110 FUNCTION GENERATOR. Safety Instruction. Safety Symbols Safety Instruction Before operating this product, please read carefully the safety symbols and definitions described here. This product complies with class I safety specifications. Installation category

More information

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-352 The Service Information provides the following information: Precautions and safety information Specifications Basic maintenance (cleaning, replacing

More information

Model: PR-55. High Voltage Oscilloscope Probe 10 kv, 40 MHz USER MANUAL

Model: PR-55. High Voltage Oscilloscope Probe 10 kv, 40 MHz USER MANUAL Model: PR-55 High Voltage Oscilloscope Probe 10 kv, 40 MHz USER MANUAL 1 2017 All rights reserved. B&K Precision products are covered by US and foreign patents, issued and pending. Information is this

More information

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual. Manual Title: 5502E Getting Started Supplement Issue: 3 Part Number: 4155211 Issue Date: 9/18 Print Date: November 2012 Page Count: 12 Revision/Date: This supplement contains information necessary to ensure

More information

User s Manual Current Probe. IM E 2nd Edition IM E

User s Manual Current Probe. IM E 2nd Edition IM E User s Manual 700937 Current Probe 2nd Edition Introduction Thank you for purchasing the 700937 Current Probe. This Instruction Manual contains useful information about the instrument s functions and operating

More information

DM-45 Digital Multimeter

DM-45 Digital Multimeter INSTRUCTION MANUAL DM-45 Digital Multimeter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Description The Greenlee DM-45 Digital

More information

BENNING. CM7 Electrical Tester. Service Information

BENNING. CM7 Electrical Tester. Service Information BENNING CM7 Electrical Tester Service Information TABLE OF CONTENTS Page Introduction 1 Precautions and Safety Information 1 Symbols 1 Safety 2 Specifications 3 General Specification 3 Voltage Specification

More information

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual. Manual Title: 550A Getting Started Supplement Issue: Part Number: 415509 Issue Date: 9/18 Print Date: November 01 Page Count: 19 Revision/Date: This supplement contains information necessary to ensure

More information

Model 4007DDS. 7 MHz Sweep Function Generator

Model 4007DDS. 7 MHz Sweep Function Generator Model 4007DDS 7 MHz Sweep Function Generator 1 Model 4007DDS - Instruction Manual Limited Two-Year Warranty B&K Precision warrants to the original purchaser that its products and the component parts thereof,

More information

USER'S MANUAL DMR-6700

USER'S MANUAL DMR-6700 USER'S MANUAL Multimeter True RMS DMR-6700 CIRCUIT-TEST ELECTRONICS www.circuittest.com Introduction This meter measures AC/DC Voltage, AC/DC Current, Resistance, Capacitance, Frequency (electrical & electronic),

More information

5MHz FUNCTION GENERATOR

5MHz FUNCTION GENERATOR 5MHz FUNCTION GENERATOR MODEL GF-8056 User s Manual Elenco TM Electronics, Inc. Copyright 2004 by Elenco TM Electronics, Inc. All rights reserved. 753117 No part of this book shall be reproduced by any

More information

5MHz FUNCTION GENERATOR

5MHz FUNCTION GENERATOR 5MHz FUNCTION GENERATOR MODEL GF-8056 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com User s Manual Elenco TM Electronics, Inc.

More information

INSTRUCTION MANUAL MODEL 4010A. 2 MHz FUNCTION GENERATOR MANUAL DE INSTRUCCIONES MODELO 4010A. 2MHz GENERADOR DE FUNCIONES

INSTRUCTION MANUAL MODEL 4010A. 2 MHz FUNCTION GENERATOR MANUAL DE INSTRUCCIONES MODELO 4010A. 2MHz GENERADOR DE FUNCIONES INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MODEL 4010A MODELO 4010A 2 MHz FUNCTION GENERATOR 2MHz GENERADOR DE FUNCIONES TEST INSTRUMENT SAFETY WARNING Normal use of test equipment exposes you to a certain

More information

Digital Clamp Meter Model: &

Digital Clamp Meter Model: & Digital Clamp Meter Model: 72-7224 & 72-7226 1 SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This meter is designed to meet IEC61010-1, 61010-2-032,

More information

USER'S MANUAL ACDC-100 TRMS ACDC-100. Versatile AC/DC Clamp-on Multimeter Series

USER'S MANUAL ACDC-100 TRMS ACDC-100. Versatile AC/DC Clamp-on Multimeter Series 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com USER'S MANUAL ACDC-100 TRMS ACDC-100 Versatile AC/DC Clamp-on Multimeter Series 1 1) SAFETY This manual contains information

More information

BENNING. Service Information MODEL: MM1-1 / MM1-2 / MM1-3

BENNING. Service Information MODEL: MM1-1 / MM1-2 / MM1-3 BENNING MODEL: MM1-1 / MM1-2 / MM1-3 Service Information The Service Information provides the following information: Precautions and safety information Specifications Basic maintenance (cleaning, replacing

More information

2001A. 200KHz Function Generator Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free

2001A. 200KHz Function Generator Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free 2001A 200KHz Function Generator Instruction Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com WARRANTY Global Specialties

More information

MODEL W Power Amplifier

MODEL W Power Amplifier TEGAM, INC. MODEL 2348 18.75 W Power Amplifier This owner s manual was as current as possible when this product was manufactured. However, products are constantly being updated and improved. Because of

More information

Arbitrary/Function Waveform Generators 4075B Series

Arbitrary/Function Waveform Generators 4075B Series Data Sheet Arbitrary/Function Waveform Generators Point-by-Point Signal Integrity The Arbitrary/Function Waveform Generators are versatile high-performance single- and dual-channel arbitrary waveform generators

More information

COM-POWER OPERATION MANUAL ACS W

COM-POWER OPERATION MANUAL ACS W COM-POWER OPERATION MANUAL For the ACS-250-100W 150 khz to 250 MHz 100W Power Amplifier Page 1 of 15 MANUAL_ACS-250-100W Rev. M02.15 Table of Contents Important Safety Precautions.....3 Introduction..5

More information

Model : OPERATING MANUAL Table of Contents (1)

Model : OPERATING MANUAL Table of Contents (1) Table of Contents (1) Title Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Measurement Operation A. DC

More information

Appendix A: Specifications

Appendix A: Specifications All specifications apply to the TDS 200-Series Digital Oscilloscopes and a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications, two conditions must first be

More information

User s Manual Current Probe. IM E 2nd Edition. Yokogawa Electric Corporation

User s Manual Current Probe. IM E 2nd Edition. Yokogawa Electric Corporation User s Manual 701930 Current Probe Yokogawa Electric Corporation 2nd Edition Foreword Revisions Thank you for purchasing the Current Probe (Model 701930). This instruction manual contains useful information

More information

User s Manual Current Probe. IM E 1st Edition. Yokogawa Electric Corporation

User s Manual Current Probe. IM E 1st Edition. Yokogawa Electric Corporation User s Manual 701932 Current Probe Yokogawa Electric Corporation 1st Edition Foreword Revisions Thank you for purchasing the 701932 Current Probe. This user's manual contains useful information about the

More information

DIGITAL MULTIMETER CONTENTS DIGITAL MULTIMETER CONTENTS

DIGITAL MULTIMETER CONTENTS DIGITAL MULTIMETER CONTENTS CONTENTS CONTENTS CONTENTS 1. SAFETY INFORMATION...1 1.1 Preliminary...1 1.2 Dos and don ts...2 1.3 Symbols...3 1.4 Precautions...4 2. DESCRIPTION...5 2.1 Names of parts...6 2.2 Switches, buttons and input

More information

GF 467F FUNCTION GENERATOR. PROTECTED RS232 + (USB OR LAN)* LabVIEW 0,01 Hz to 5 MHz CMos. Specifications. Other specifications

GF 467F FUNCTION GENERATOR. PROTECTED RS232 + (USB OR LAN)* LabVIEW 0,01 Hz to 5 MHz CMos. Specifications. Other specifications FUNCTION GENERATOR EAN CODE : 3760244880468 5 MHZ+RS232++(USB or LAN)* GF 467F COMPLETE : Reciprocal frequency counter 50 MHz. - Internal linear or logarithmic sweep, and external VCF or FM modulation.

More information

RIGOL. User s Guide. RP1000D Series High Voltage Differential Probe. Feb RIGOL Technologies, Inc

RIGOL. User s Guide. RP1000D Series High Voltage Differential Probe. Feb RIGOL Technologies, Inc User s Guide RP1000D Series High Voltage Differential Probe Feb. 2013 RIGOL Technologies, Inc Guaranty and Declaration Copyright 2012 RIGOL Technologies, Inc. All Rights Reserved. Trademark Information

More information

KMD-S04 Multímetro de bolsillo

KMD-S04 Multímetro de bolsillo www.grupotemper.com KMD-S04 Multímetro de bolsillo Table of Contents Title Page Overview ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 3 Unpacking Inspection ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 4 Safety Information

More information

LH240 LH1040 LH2040 LH2015

LH240 LH1040 LH2040 LH2015 LH240 LH1040 LH2040 LH2015 AC/DC Clamp On Multimeters Pinces Multimétriques AC/DC AC/DC Zangen-Multimeter Multimetri tenaglia c.a./c.c. Multímetros de inserción de C.A./C.C. Operating Instructions Mode

More information

INSTRUCTION MANUAL FUNCTION GENERATOR FG-274 B

INSTRUCTION MANUAL FUNCTION GENERATOR FG-274 B INSTRUCTION MANUAL FUNCTION GENERATOR FG-274 B71-0173-11 CONTENTS USING THE PRODUCT SAFELY Ⅰ-Ⅳ 1. FEATURES... 1 2. SPECIFICATIONS... 2 3. FRONT AND REAR PANELS... 5 3.1. Front Panel... 5 3.2. Rear Panel...

More information

CBA 400M MHZ to 400 MHZ

CBA 400M MHZ to 400 MHZ 1 CBA 400M-100 1 MHZ to 400 MHZ 100 watt amplifier user Manual 601-298A CBA 400M-100 1 MHZ to 400 MHZ 100 watt amplifier USER Manual CBA 400M-100 User Manual contents 1 Safety information 5 2 Introduction

More information

LH630 LH635 LH1035. Operating Instructions Mode d emploi Bedienungsanleitung Istruzioni per il funzionamento Instrucciones de Funcionamiento

LH630 LH635 LH1035. Operating Instructions Mode d emploi Bedienungsanleitung Istruzioni per il funzionamento Instrucciones de Funcionamiento LH630 LH635 LH1035 AC/DC Clamp On Multimeters Pinces Multimétriques AC/DC AC/DC Zangen-Multimeter Multimetri tenaglia c.a./c.c. Multímetros de incerción de C.A./C.C. Operating Instructions Mode d emploi

More information

Appendix A: Specifications

Appendix A: Specifications Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Appendix A: Specifications This section provides a complete description of the video measurement set specifications.

More information

ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL

ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL 1 1. SAFETY INFORMATION SAFETY SYMBOLS Warning! Dangerous Voltage (Risk of electric shock). Caution! Refer to the user s manual before using this

More information

Model MHz Arbitrary Waveform / Function Generator

Model MHz Arbitrary Waveform / Function Generator Verification and Adjustment Manual 3390-905-01 Rev. B / May 2016 www.tek.com/keithley Model 3390 50 MHz Arbitrary Waveform / Function Generator *P3390-905-01B* 3390-905-01 A Greater Measure of Confidence

More information

AMM-1022 Digital Multimeter USER`S MANUAL

AMM-1022 Digital Multimeter USER`S MANUAL Digital Multimeter USER`S MANUAL www.tmatlantic.com CONTENTS 1. SAFETY INFORMATION.3 2. DESCRIPTION..6 3. SPECIFICATIONS.8 4. OPERATING INSTRUCTION..11 4.1 Voltage measurement...11 4.2 Current measurement

More information

User s Manual Current Probe IM E. 8th Edition

User s Manual Current Probe IM E. 8th Edition User s Manual 701931 Current Probe 8th Edition Thank you for purchasing the Current Probe (Model 701931). This instruction manual contains useful information about the instrument s functions and operating

More information

TEGAM, INC. SINGLE/DUAL CHANNEL HIGH VOLTAGE AMPLIFIER MODEL 2340/2350. Instruction Manual PN# CD Publication Date: June 2006 REV.

TEGAM, INC. SINGLE/DUAL CHANNEL HIGH VOLTAGE AMPLIFIER MODEL 2340/2350. Instruction Manual PN# CD Publication Date: June 2006 REV. TEGAM, INC. SINGLE/DUAL CHANNEL HIGH VOLTAGE AMPLIFIER MODEL 2340/2350 Instruction Manual PN# 810044-CD Publication Date: June 2006 REV. C This owner s manual was as current as possible when this product

More information

Agilent 1146A AC/DC Oscilloscope Current Probe

Agilent 1146A AC/DC Oscilloscope Current Probe A User s Guide Publication number 01146-92003 May 2005 Copyright Agilent Technologies 1996-2005 All Rights Reserved Contents Receiving Your Shipment -2 Packaging -2 Description -3 Compatibility -3 Control

More information

Power supply CP-D 24/4.2 Primary switch mode power supply

Power supply CP-D 24/4.2 Primary switch mode power supply Data sheet Power supply CP-D 24/4.2 Primary switch mode power supply The CP-D range of modular power supply units in MDRC design (modular DIN rail components) is ideally suited for installation in distribution

More information

TT-SI 9001 / TT-SI MHz Active Differential Probes

TT-SI 9001 / TT-SI MHz Active Differential Probes INSTRUCTION MANUAL TT-SI 9001 / TT-SI 9002 25MHz Active Differential Probes These probes are in compliance with IEC-61010-031 CAT III, Pollution Degree 2 1. Safety Terms and Symbols Terms appear in this

More information

INSTRUCTION MANUAL ACD-10 PRO & TRMS PRO

INSTRUCTION MANUAL ACD-10 PRO & TRMS PRO INSTRUCTION MANUAL ACD-10 PRO & TRMS PRO AMPROBE 1 Congratulations! You are now the owner of an AMPROBE Instrument. It has been quality crafted according to quality standards and contains quality components

More information

V1.3. TBLC08 50mH AC-LISN TBLC08

V1.3. TBLC08 50mH AC-LISN TBLC08 V1.3 TBLC08 The TBLC08 is a Line Impedance Stabilization Network for the measurement of line-conducted interference within the range of 9kHz to 30MHz, according to the CISPR16 standard. The device is designed

More information

Keysight N2790A Differential Voltage Probe. User Guide

Keysight N2790A Differential Voltage Probe. User Guide Keysight N2790A Differential Voltage Probe User Guide Notices Keysight Technologies 2013-2014, 2015, 2018 No part of this manual may be reproduced in any form or by any means (including electronic storage

More information

N acquisitions, all channels simultaneously, N is selectable from 4, 16, 64, and 128 Inputs

N acquisitions, all channels simultaneously, N is selectable from 4, 16, 64, and 128 Inputs With compliments All specifications apply to the TDS 200-Series Digital Real-Time Oscilloscope with a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications,

More information

E2621A and E2622A Probe Adapters for Infiniium Oscilloscopes. User s Guide. Publication number E September 2002

E2621A and E2622A Probe Adapters for Infiniium Oscilloscopes. User s Guide. Publication number E September 2002 User s Guide sa Publication number E2621-92003 September 2002 For Safety, Regulatory, and publishing information, see the pages at the back of this book. Copyright Agilent Technologies 1999-2002 All Rights

More information

SAFETY PRECAUTIONS: Before use, read the following safety precautions

SAFETY PRECAUTIONS: Before use, read the following safety precautions [1] SAFETY PRECAUTIONS: Before use, read the following safety precautions This instruction manual explains how to use your multimeter CD731, CD751 safely. Before use, please read this manual thoroughly.

More information

USER'S MANUAL. ACD-6 Pro. ACD-6 TRMS Pro. Versatile Clamp-on Multimeter Series

USER'S MANUAL. ACD-6 Pro. ACD-6 TRMS Pro. Versatile Clamp-on Multimeter Series USER'S MANUAL ACD-6 Pro ACD-6 TRMS Pro Versatile Clamp-on Multimeter Series 1 1) SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and maintaining

More information

MODEL 3810/2 Line Impedance Stabilization Network

MODEL 3810/2 Line Impedance Stabilization Network EMC TEST SYSTEMS FEBRUARY 1996 REV C PN 399197 MODEL 3810/2 Line Impedance Stabilization Network OPERATION MANUAL USA P.O. Box 80589 Austin, Texas 78708-0589 2205 Kramer Lane, Austin, Texas 78758-4047

More information

AC/DC Clamp Meter. Owner's Manual. Model No Safety Operation Maintenance Español

AC/DC Clamp Meter. Owner's Manual. Model No Safety Operation Maintenance Español Owner's Manual AC/DC Clamp Meter Model No. 82369 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product. Safety Operation Maintenance Español

More information

THURLBY THANDAR INSTRUMENTS. TGA1240 SERIES 40MHz ARBITRARY WAVEFORM GENERATORS INSTRUCTION MANUAL

THURLBY THANDAR INSTRUMENTS. TGA1240 SERIES 40MHz ARBITRARY WAVEFORM GENERATORS INSTRUCTION MANUAL THURLBY THANDAR INSTRUMENTS TGA1240 SERIES 40MHz ARBITRARY WAVEFORM GENERATORS INSTRUCTION MANUAL Table of Contents Overview 3 Specifications 5 EMC 13 Safety 14 Installation 15 Connections 17 Front Panel

More information

79/26 Series III Multimeter

79/26 Series III Multimeter 79/26 Series III Multimeter Instruction Sheet W Read First: Safety Information Never use the meter if the meter or test leads look damaged. Be sure the test leads and switch are in the correct position

More information

PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D

PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D T8211D 1 1. SAFETY INFORMATION BE EXTREMELY CAREFUL IN THE USE OF THIS METER. Improper use of this device can result in electric shock or destroy of

More information

DDS Function Generator

DDS Function Generator Model: 4007B, 4013B DDS Function Generator USER MANUAL Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all phases of operation,

More information

9 Specifications. Specifications NOMINAL CHARACTERISTICS

9 Specifications. Specifications NOMINAL CHARACTERISTICS 9 Specifications Specifications NOMINAL CHARACTERISTICS WARRANTED CHARACTERISTICS Nominal characteristics describe parameters and attributes that are guaranteed by design, but do not have associated tolerances.

More information

HAWK5000 Operators Manual

HAWK5000 Operators Manual HAWK5000 Operators Manual Keison Products P.O. Box 2124, Chelmsford CM1 3UP, England Tel: +44 (0) 1245 600560 Fax: +44 (0) 1245 600030 Email: sales@keison.co.uk www.keison.co.uk KANE INTERNATIONAL LIMITED

More information

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use True RMS Digital Multimeter DVM98 1 Safety information This multimeter has been designed according to IEC - 1010 concerning electronic measuring instruments with an overvoltage category (CAT II) and pollution

More information

Model and

Model and Function Generator Model 72-14110 and 72-14111 0 Contents Function Generator... 0 Model 72-14110 and 72-14111... 0 Chapter 1 Safety Information... 3 1.1 Safety Terms and Symbols... 3 1.2 General Safety

More information

AC/DC Current Probe GCP-100 QUICK START GUIDE ISO-9001 CERTIFIED MANUFACTURER

AC/DC Current Probe GCP-100 QUICK START GUIDE ISO-9001 CERTIFIED MANUFACTURER AC/DC Current Probe GCP-100 QUICK START GUIDE ISO-9001 CERTIFIED MANUFACTURER This manual contains proprietary information, which is protected by copyright. All rights are reserved. No part of this manual

More information

Tablet Oscilloscope Safety Information

Tablet Oscilloscope Safety Information Tablet Oscilloscope Safety Information Shenzhen Micsig Instruments Co., Ltd. General Safety Summary To use the instrument safely, please follow safety precautions carefully and obey the well-known safety

More information

Chapter 6 Specifications

Chapter 6 Specifications RIGOL This chapter lists the technical specifications and general specifications of the RF signal generator. The technical specifications are valid when the instrument is within the calibration period,

More information

TT-SI MHz Active Differential Probe

TT-SI MHz Active Differential Probe INSTRUCTION MANUAL TT-SI 9101 100MHz Active Differential Probe These probe is in compliance with IEC-61010-031 CAT III, Pollution Degree 2 1. Safety Terms and Symbols Terms appear in this manual: WARNING.

More information

AC/DC CLAMP METER USER S MANUAL

AC/DC CLAMP METER USER S MANUAL AC/DC CLAMP METER USER S MANUAL CONTENTS PAGE SAFETY INFORMATION SYMBOL EXPLANATION SAFETY PRECAUTIONS 1 1 2 MAINTENANCE 3 GENERAL DESCRIPTION 4 PANEL DESCRIPTION 4 OPERATING INSTRUCTIONS... 7 SPECIFICATIONS

More information

Digital Function Generator

Digital Function Generator Digital Function Generator 13654-99 PHYWE Systeme GmbH & Co. KG Robert-Bosch-Breite 10 37079 Göttingen Germany Tel. +49 (0) 551 604-0 Fax +49 (0) 551 604-107 E-mail info@phywe.de Operating Instructions

More information

TA MHz ±700 V Differential Probe User s Manual. This probe complies with IEC , IEC CAT III, Pollution Degree 2.

TA MHz ±700 V Differential Probe User s Manual. This probe complies with IEC , IEC CAT III, Pollution Degree 2. TA041 25 MHz ±700 V Differential Probe User s Manual This probe complies with IEC-1010.1, IEC-1010.2-031 CAT III, Pollution Degree 2. 1. Safety terms and symbols Terms appearing in this manual: WARNING

More information

Multi range AC current clamps (1000A / 100A / 5A / 0.5A) A 1281 Instruction manual Version 2.0, Code no

Multi range AC current clamps (1000A / 100A / 5A / 0.5A) A 1281 Instruction manual Version 2.0, Code no (1000A / 100A / 5A / 0.5A) A 1281 Instruction manual Version 2.0, Code no. 20 751 696 Distributor: Manufacturer: METREL d.d. Ljubljanska cesta 77 1354 Horjul Slovenia web site: http://www.metrel.si e-mail:

More information

FUNCTION GENERATOR OPERATION MANUAL

FUNCTION GENERATOR OPERATION MANUAL FUNCTION GENERATOR OPERATION MANUAL INDEX 1. Introduction (3) 2. Specifications (3) 3. Working Theory (7) 4. Structure (8) 5. Operation & Maintenance (9) 6. Accessories (14) 1 This instrument is a highly

More information

User s Guide. 400A AC/DC Clamp Meter. Model MA Washington Street Melrose, MA Phone Toll Free

User s Guide. 400A AC/DC Clamp Meter. Model MA Washington Street Melrose, MA Phone Toll Free User s Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 400A AC/DC Clamp Meter Model MA220 Introduction Thank you for selecting

More information

DUAL CHANNEL BROADBAND LINEAR AMPLIFIER Model A800D

DUAL CHANNEL BROADBAND LINEAR AMPLIFIER Model A800D DUAL CHANNEL BROADBAND LINEAR AMPLIFIER Model A800D HIGH VOLTAGE FIXED GAIN BROADBAND 800Vpp 60mA 100x DC to ca 200 khz LOW OUTPUT IMPEDANCE HIGH SLEW RATE

More information

T L Audio CRIMSON SERIES. User Manual EQ-3011 EQUALISER. Tony Larking Professional Sales Limited, Letchworth, England.

T L Audio CRIMSON SERIES. User Manual EQ-3011 EQUALISER. Tony Larking Professional Sales Limited, Letchworth, England. T L Audio CRIMSON SERIES User Manual EQ-3011 EQUALISER Tony Larking Professional Sales Limited, Letchworth, England. Tel: 01462 490600. International +44 1462 490600. Fax: 01462 490700. International +44

More information

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.

Manual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual. Manual Title: 5522A Getting Started Supplement Issue: 10 Part Number: 3795091 Issue Date: 9/18 Print Date: January 2011 Page Count: 18 Revision/Date: This supplement contains information necessary to ensure

More information

1. SAFETY INFORMATION.1 2. DESCRIPTION SPECIFICATIONS.6 4. OPERATING INSTRUCTION Voltage measurement Current measurement 10

1. SAFETY INFORMATION.1 2. DESCRIPTION SPECIFICATIONS.6 4. OPERATING INSTRUCTION Voltage measurement Current measurement 10 CONTENTS 1. SAFETY INFORMATION.1 2. DESCRIPTION..4 3. SPECIFICATIONS.6 4. OPERATING INSTRUCTION..9 4.1 Voltage measurement...10 4.2 Current measurement 10 4.3 Resistance measurement...12 4.4 Diode test.12

More information

User s Guide. 400A AC/DC Clamp Meter. Model MA220

User s Guide. 400A AC/DC Clamp Meter. Model MA220 User s Guide 400A AC/DC Clamp Meter Model MA220 Introduction Thank you for selecting the Extech MA200 AC/DC Clamp Meter. This meter measures AC/DC Current, AC/DC Voltage, Resistance, Capacitance, Frequency,

More information

1. BP4620 SPECIFICATIONS

1. BP4620 SPECIFICATIONS 1. SPECIFICATIONS 1. SPECIFICATIONS 1-1 1.1 Specification Conditions 1-2 1.2 Output 1-3 1.3 Output Limiters 1-5 1.4 Signal Sources 1-6 1.5 Monitor Output 1-7 1.6 Measurement Functions 1-7 1.7 Sequence

More information

DIGIT & POINTER MULTIMETER

DIGIT & POINTER MULTIMETER CONTENTS DIGIT & POINTER MULTIMETER OPERATOR S MANUAL 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 3 1.4 MAINTENANCE 3 2. DESCRIPTION 4 2.1 NAMES OF COMPONENTS 4 2.2 FUNCTION

More information

HZ 115. Differential probe for oscilloscopes. C E IEC 1010 Cat III

HZ 115. Differential probe for oscilloscopes. C E IEC 1010 Cat III HZ 115 Differential probe for oscilloscopes 1500 V input voltage max. 30 MHz bandwidth x 100 and x 1000 attenuation 50 db CMRR (1MHz) User-friendliness through a microcontroller Automatic Switch-off Beep

More information

Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES

Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES TABLE OF CONTENTS / EN TITLE TABLE OF CONTENTS PAGE 1. SAFETY INFORMATION... 1 2. TECHNICAL SPECIFICATIONS... 2 3. PARTS & CONTROLS...

More information

Model 3725/2M. Line Impedance Stabilization Network (LISN) User Manual

Model 3725/2M. Line Impedance Stabilization Network (LISN) User Manual Model 3725/2M Line Impedance Stabilization Network (LISN) User Manual ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any

More information

Tektronix: Products > AWG 2040 Arbitrary Waveform Generator

Tektronix: Products > AWG 2040 Arbitrary Waveform Generator Page 1 of 7 Arbitrary Waveform Generator AWG 2040 This product is no longer carried in our catalog. Features 1.024 GS/sec Clock Rate Provides up to 500 MHz Waveforms 1 MB Record Length (4 MB with Opt.

More information

TT-SI MHz DIFFERENTIAL PROBE

TT-SI MHz DIFFERENTIAL PROBE TT-SI 9110 100MHz DIFFERENTIAL PROBE USER S MANUAL This probe is in compliance with IEC-1010.1, IEC - 1010. 2-031 CATⅢ, Pollution Degree 2. 1. Safety Terms and Symbols Terms appear in this manual: WARNING.

More information

DIGITAL MULTIMETER OPERATOR'S INSTRUCTION MANUAL HOLD 10A COM LIGHT MS8265 ON/OFF. 200M KHz 2K 20K μ μ μ n.

DIGITAL MULTIMETER OPERATOR'S INSTRUCTION MANUAL HOLD 10A COM LIGHT MS8265 ON/OFF. 200M KHz 2K 20K μ μ μ n. MS8265 DIGITAL MULTIMETER OPERATOR'S INSTRUCTION MANUAL HOLD ON/OFF LIGHT 1000V CAT II 600V CAT III MS8265 200K 2M 20M 20K 200M KHz 2K 20 200 2 20 200μ 200 20μ 750 2μ 1000 200n F 20n 10A 2m 200m 10 10

More information

1157A 2.5 GHz Active Probe

1157A 2.5 GHz Active Probe User s Guide A Publication number 01157-97002 September 2005 For Safety and Regulatory information, see the pages at the back of this guide. Copyright Agilent Technologies 2001-2002, 2005 All Rights Reserved.

More information

FREQUENCY SYNTHESIZERS, SIGNAL GENERATORS

FREQUENCY SYNTHESIZERS, SIGNAL GENERATORS SYNTHESIZED SIGNAL GENERATOR MG3641A/MG3642A 12 khz to 1040/2080 MHz NEW New Anritsu synthesizer technology permits frequency to be set with a resolution of 0.01 Hz across the full frequency range. And

More information

1156A 1.5 GHz Active Probe

1156A 1.5 GHz Active Probe User s Guide A Publication number 01156-97002 September 2005 For Safety and Regulatory information, see the pages at the back of this guide. Copyright Agilent Technologies 2001-2002, 2005 All Rights Reserved.

More information

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range SPECIFICATIONS NI PXIe-4610 Power Amplifier This document lists specifications for the NI PXIe-4610 Power Amplifier. These specifications are typical at 25 ºC unless otherwise stated. The operating range

More information

Model ST Instruction Manual. True RMS Autoranging Digital Multimeter. reedinstruments. www. com

Model ST Instruction Manual. True RMS Autoranging Digital Multimeter. reedinstruments. www. com Model ST-9933 True RMS Autoranging Digital Multimeter Instruction Manual reedinstruments com Table of Contents Safety... 3 Features... 4 Specifications...4-8 Technical...4-5 Accuracy...5-8 Display Description...

More information

TA MHz oscilloscope probe TA MHz oscilloscope probe

TA MHz oscilloscope probe TA MHz oscilloscope probe TA375 100 MHz oscilloscope probe TA386 200 MHz oscilloscope probe User's Guide X1 X10 TA386 X1/X10 Max. 600 Vp Introduction This passive high-impedance oscilloscope probe is suitable for most oscilloscopes

More information

Model Hz to 10MHz Precision Phasemeter. Operating Manual

Model Hz to 10MHz Precision Phasemeter. Operating Manual Model 6610 1Hz to 10MHz Precision Phasemeter Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give long

More information

1147A 50 MHz Current Probe

1147A 50 MHz Current Probe A User s Guide Publication number 01147-92003 September 2005 For Safety information, Regulatory information, and publishing information, see the pages at the end of this book. Copyright Agilent Technologies

More information

TT-SI MHz Active Differential Probe

TT-SI MHz Active Differential Probe INSTRUCTION MANUAL TT-SI 9110 100MHz Active Differential Probe These probe is in compliance with EN61010-031:2002+A1:2008 CAT III, Pollution Degree 2 1. Safety Terms and Symbols Terms appear in this manual:

More information

N2790A Differential Voltage Probe

N2790A Differential Voltage Probe N2790A Differential Voltage Probe User s Guide For Safety, Regulatory, and publishing information, see the pages at the back of this book. Copyright Agilent Technologies 2009 All Rights Reserved. A Contents

More information

INSTRUCTION MANUAL. Model 4012A. 5 MHz SWEEP FUNCTION GENERATOR. with DIGITAL DISPLAY

INSTRUCTION MANUAL. Model 4012A. 5 MHz SWEEP FUNCTION GENERATOR. with DIGITAL DISPLAY INSTRUCTION MANUAL Model 4012A 5 MHz SWEEP FUNCTION GENERATOR with DIGITAL DISPLAY TEST INSTRUMENT SAFETY WARNING Normal use of test equipment exposes you to a certain amount of danger from electrical

More information