AQxx Series 450W Discrete Unidirectional TVS Diode

Transcription

1 AQxx Series 5W Discrete Unidirectional TVS Diode RoHS Pb GREEN Description The unidirectional AQxx series is designed to replace multilayer varistors (MLVs) in electronic equipment for low speed and DC applications. It will protect any sensitive equipment from damage due to electrostatic discharge (ESD) and other transient events. The AQxx series can safely absorb repetitive ESD strikes at ±3kV (contact discharge, IEC --) without performance degradation and safely dissipate 3A (AQ5) of /μs induced surge current (IEC --5) with very low clamping voltages. Pinout and Functional Block Diagram 1 Features ESD, IEC --, ±3kV contact, ±3kV air EFT, IEC --, A (5/5ns) Lightning, IEC - -5 nd edition, 3A (t P =/μs, AQ5) Low clamping voltage Low leakage current Small SOD33 package fits 5 footprints AEC-Q1 qualified Moisture Sensitivity Level(MSL -1) Halogen free, lead free and RoHS compliant Applications Switches / Buttons Test Equipment / Instrumentation Point-of-Sale Terminals Medical Equipment Notebooks / Desktops / Servers Computer Peripherals CAN Bus protection Automotive applications Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. Revision: 9/1/17

2 Absolute Maximum Ratings Symbol Parameter Value Units P pk Peak Pulse Power ( =/μs) 5 W T OP Operating Temperature - to 15 C T STOR Storage Temperature -55 to 15 C Notes: CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. AQ5 Electrical Characteristics (T OP =5ºC) 1μA 5. V =1mA. V =5V 1. μa Clamp Voltage 1 V C =1A, =/µs, Fwd 9. V =A, t P =/μs, Fwd 13. V Dynamic Resistance R DYN TLP, tp=ns, I/O to Ground. Ω =/µs 3. A IEC -- (Contact Discharge) ±3 kv IEC -- (Air Discharge) ±3 kv Diode Capacitance 1 C D Reverse Bias=V, f=1mhz 35 pf AQ1 Electrical Characteristics (T OP =5ºC) 1μA 1. V =1mA 13.3 V =1V 1. μa Clamp Voltage 1 V C =1A, =/µs, Fwd 1.5 V =A, t P =/μs, Fwd.5 V Dynamic Resistance R DYN TLP, tp=ns, I/O to Ground.9 Ω =/µs 17. A IEC -- (Contact Discharge) ±3 kv IEC -- (Air Discharge) ±3 kv Diode Capacitance 1 C D-GND Reverse Bias=V, f=1mhz 15 pf Revision: 9/1/17

3 AQ15 Electrical Characteristics (T OP =5ºC) 1μA 15. V =1mA 1.7 V =15V 1. μa I Clamp Voltage 1 PP =1A, =/µs, Fwd. V V C =A, =/µs, Fwd 3. V Dynamic Resistance R DYN TLP, tp=ns, I/O to Ground.3 Ω =/µs 1. A IEC -- (Contact Discharge) ±3 kv IEC -- (Air Discharge) ±3 kv Diode Capacitance 1 C I/O-GND Reverse Bias=V, f=1mhz pf AQ Electrical Characteristics (T OP =5ºC) 1μA. V =1mA.7 V =V 1. μa I Clamp Voltage 1 PP =1A, =/µs, Fwd 3. V V C =5A, =/µs, Fwd. V Dynamic Resistance R DYN TLP, tp=ns, I/O to Ground.9 Ω =/µs 7. A IEC -- (Contact Discharge) ±3 kv IEC -- (Air Discharge) ±3 kv Diode Capacitance 1 C I/O-GND Reverse Bias=V, f=1mhz 5 pf AQ3 Electrical Characteristics (T OP =5ºC) 1μA 3. V =1mA. V =3V 1. μa I Clamp Voltage 1 PP =1A, =/µs, Fwd 5. V V C =5A, =/µs, Fwd. V Dynamic Resistance R DYN TLP, tp=ns, I/O to Ground.1 Ω =/µs 5. A IEC -- (Contact Discharge) ±3 kv IEC -- (Air Discharge) ±3 kv Diode Capacitance 1 C I/O-GND Reverse Bias=V, f=1mhz 5 pf Note: 1. Parameter is guaranteed by design and/or component characterization..transmission Line Pulse (TLP) with ns width, ns rise time, and average window t1=7ns to t= 9ns Revision: 9/1/17

4 Non-Repetitive Peak Pulse Power vs. Pulse Time Capacitance vs. Bias Peak Pulse Power - P pk (kw) Pulse Duration - tp (µs) Capacitance (pf) AQ AQ1 AQ15 3 AQ SDC AQ3 SD3C Bias Voltage (V) Power Derating Curve /μs Pulse Waveform % of Rated Power Ambient Temperature - T A ( o C) Percent of 1% % 9% % 7% % 5% % 3% % % % Time (μs) AQ5 Transmission Line Pulsing(TLP) Plot AQ1 Transmission Line Pulsing(TLP) Plot Revision: 9/1/17

5 Temperature TVS Diode Arrays (SPA Diodes) AQ15 Transmission Line Pulsing(TLP) Plot AQ Transmission Line Pulsing(TLP) Plot AQ3 Transmission Line Pulsing(TLP) Plot Product Characteristics 1 Lead Plating Lead Material Matte Tin Copper Alloy Lead Coplanarity Substrate material. inches (.mm) Silicon Body Material Molded Epoxy UL Recognized epoxy meeting Flammability flammability rating V-. Notes : 1. All dimensions are in millimeters. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr.. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI Soldering Parameters Reflow Condition Pre Heat - Temperature Min (T s(min) ) 15 C - Temperature Max (T s(max) ) C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP - Time (min to max) (t s ) 1 secs Average ramp up rate (Liquidus) Temp (T L ) to peak 3 C/second max T L T S(max) Preheat t L Ramp-down T S(max) to T L - Ramp-up Rate 3 C/second max - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) 15 seconds Peak Temperature (T P ) +/-5 C T S(min) 5 t S time to peak temperature Time Time within 5 C of actual peak Temperature ( ) seconds Ramp-down Rate C/second max Time 5 C to peak Temperature (T P ) minutes Max. Do not exceed C Revision: 9/1/17

6 c. D b TVS Diode Arrays (SPA Diodes) Part Numbering System Automotive Grade TVS Diode Arrays (SPA Diodes) Voltage Number of Channels AQ ** 1 F T G G= Green T= Tape & Reel Package F: SOD33 Ordering Information Part Number Package Marking Min. Order Qty. AQ5-1FTG SOD33 g 3 AQ1-1FTG SOD33 g1 3 AQ15-1FTG SOD33 g 3 AQ-1FTG SOD33 g3 3 AQ3-1FTG SOD33 g 3 Part Marking System g * 1 Blank: SD5-1FTG AQ5-1FTG 1: SD1-1FTG AQ1-1FTG : SD15-1FTG AQ15-1FTG 3: SD-1FTG AQ-1FTG : SD3-1FTG AQ3-1FTG Package Dimensions -SOD33 E E1 L1.5 A1 A A Recommended Solder Pad SOD33 Symbol Millimeters Inches Min Max Min Max A A1.... A b c D E E L Unit: mm Revision: 9/1/17

7 Top Cover Tape 3 REF TVS Diode Arrays (SPA Diodes) W A F B E K P1 Φ:.±.5 Embossed Carrier Tape & Reel Specification SOD33 W1 S ComponentOrientationinTape R M N W H K Symbol Millimeters A 1.3min/1.max B.9+/-. W.+.3/-. D D1 ø1.min/ø1.5max E 1.75+/-. E - F 3.5+/-.5 P.+/-. P.+/-. P1.+/-.5 K 1.15min/1.5max T.5+/-.13 Pin1 mm TAPE AND REEL Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at Revision: 9/1/17