PSK, PSS Series Data Sheet Positive Switching Regulators

Transcription

1 4.4" 3 U 4.4" 3 U " 2 TE " " 6 TE " Description The PSK/PSS Series of positive switching regulators is designed as power supplies for electronic systems, where no input-to-output isolation is required. Their major advantages include a high level of efficiency, high reliability, low output ripple, and excellenynamic response. Models with input voltages up to 44 V are specially designed for secondary switched and battery-driven mobile applications. The converters are suitable for railway applications according to EN 5055 and EN 502. Two type of housings are available allowing operation up to 7 C. They are designed for insertion into a 9" DIN-rack or for chassis mounting. Replacing the heat sink by an optional cooling plate, allows chassis or wall mounting on top of a metal surface, acting as heat sink. Various options are available to adapt the converter to different applications. Connector type: H5 or H5S4, depending on output current. Features RoHS lead-free-solder and lead-solder-exempted products are available Input voltage up to 44 VDC Single output of 3.3 to 48 VDC No input-to-output isolation High efficiency up to 97% Extremely wide input voltage range Low input-to-outpuifferential voltage Very good dynamic properties Input undervoltage lockout Active current sharing for parallel operation Output voltage adjustment, inhibit, and sense lines Continuously no-load and short-circuit proof All boards are coated with a protective lacquer Safety-approved to IEC/EN and UL/CSA nd Ed. Table of Contents Page Page Description... Model Selection... 2 Functional Description... 3 Electrical Input Data... 4 Electrical Output Data... 6 Auxiliary Functions... 0 Electromagnetic Compatibility (EMC)... 2 Immunity to Environmental Conditions... 4 Mechanical Data... 5 Safety and Installation Instructions... 8 Description of Options... 9 Accessories BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page of 20

2 Model Selection Table : All models Output Output Operating input Nom. input Efficiency 2 Type Connector Options voltage current voltage range voltage designation type V o nom [V] I o nom [A] V i [V] V i nom [V] η min [%] η typ [%] PSK3E25-7 H5S4 B, B PSS5A2-9 H5 B, B, G PSS5A4-2 4 H5 B, B PSK5A6-9 H5-7, E, P, C, B, B, G PSK5A8-2 4 H5 B, B PSK5A20-9 H5S4-7, E, P, C, K, B, B, G PSK5A25-9 H5S4-7, E, P, C, K, B, B, G PSS29-9 H5-7, E, B, B, G PSS22-9 H5 B, B, G PSK22-9 H5-7, E, P, C, B, B, G PSS H5 B, B PSK26-9 H5-7, E, P, C, B, B, G PSK28-2 H5 B, B PSK220-9 H5S4-7, E, P, C, K, B, B, G PSS29-9 H5-7, E, B, B, G PSS22-9 H5 B, B, G PSK22-9 H5-7, E, P, C, B, B, G PSS H5 B, B PSK26-9 H5-7, E, P, C, B, B, G PSK H5 B, B PSK220-9 H5S4-7, E, P, C, K, B, B, G PSS249-9 H5-7, E, P, C, B, B, G PSS242-9 H5-7, E, P, B, B, G PSK242-9 H5-7, E, P, C, B, B, G PSS H5 B, B PSK246-9 H5-7, E, P, C, B, B, G PSK H5 B, B PSK H5S4-7, E, P, C, K, B, B, G PSS369-9 H5-7, E, P, B, B, G PSS362-9 H5 B, B, G PSK362-9 H5-7, E, P, C, B, B, G PSK366-9 H5-7, E, P, C, B, B, G PSK H5S4-7, E, P, C, K, B, B, G PSS489-9 H5 B, B PSK482-9 H5-7, E, P, C, B, B, G Surges up to 56 V for 2 s; see Electrical Input Data 2 Efficiency at V i nom and I o nom. Models with opt. K (standard H5 connector) exhibit approx. to 2% lower efficiency. 3 Output voltage V o set to 5 V by R input 4 Use other PSK/PSS models with same case size (PSK or PSS) and same connector (H5 or H5S4). Note: Non-standard input/output configurations or special custom adaptions are available on request. NFND: Not for new designs Preferred for new designs BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 2 of 20

3 Part Number Description Positive switching regulator in case S0, K0... PSS, PSK Nominal output voltage in Volt Nominal output current in Ampere PSK E P C B G Operational ambient temperature range T A 0 to 50 C to 7 C to 7 C (optional) Options: Inrush current limitation... E Potentiometer to adjust V o... P Thyristor crowbar... C Standard H5 connector... K Cooling plate large/small... B, B RoHS-compliant for all 6 substances... G 2 Option P excludes R-features and vice versa. 2 G is always placed at the end of the part number. Example: PSS29-9EPCB = Positive switching regulator with output 2 V, 9 A, ambient temperature range of 25 to 7 C, inrush current limitation, potentiometer, crowbar, and large cooling plate option B. Note: The sequence of options must follow the order above. allocation, identification of LED, test sockets, and optional potentiometer. Product Marking Label with input voltage range, output voltage and current, Type designation, applicable approvals marks, warnings, pin protection degree, batch and serial no., and data code including production site, version, and date of production. Functional Description The switching regulators are using the buck topology. The input is not electrically isolated from the output. During the on period of the switching FET, current is transferred to the output, and energy is stored in the output choke. During the off period, this energy forces the current to continue flowing through the output choke and the freewheeling diode to the load. Regulation is accomplished by varying on/off duty cycle. Switching frequency is approx. 00 khz. The converters exhibit an undervoltage monitor to prevent high currents at low input voltage, but no overvoltage monitor. These regulators are ideal for applications, where an input to output isolation is not necessary or where it is already provided by an external front end, e.g. a transformer with rectifier. To optimize customer s needs, various options and accessories are available. V i I i Vi+ Gi Fig. Block diagram Fuse Option E Input Filter C i Option C Control circuit Option P BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 3 of 20 C o a 4 6 Vo+ 20 S+ 22 T 4 i 6 R 8 S 8 0 Go I o V o

4 Electrical Input Data Table 2a: Inpuata. General Conditions: T A = 25 C, unless T C is specified Input PSS5A4 PSS24 PSS244 Unit PSK5A8 PSK28 PSK248 Characteristics Conditions min typ max min typ max min typ max V i Operating input voltage I o = 0 I o nom / VDC V io min Min. diff. voltage V i V o T C min T C max 2.9 3/4 5 V i o Undervoltage lockout I i 0 No load input current I o = 0, V i min V i max ma I inr p Peak value of inrush current V i nom, with option E A C x Input capacitance µf The second value is valid, if output is set to 5 V with the R-input. Table 2b: Inpuata. General Conditions: T A = 25 C, unless T C is specified Input PSK3E25 PSS5A2 PSS22 Unit PSK5A25 PSK5A6 PSK26 PSK5A20 PSK220 Characteristics Conditions min typ max min typ max min typ max V i Operating input voltage I o = 0 I o nom VDC V io min Min. diff. voltage V i V o T C min T C max 4.7/ V i o Undervoltage lock-out I i 0 No load input current I o = 0, V i min V i max ma I inr p Peak value of inrush current V i nom, with option E A C x Input capacitance µf Values for PSK3E25/PSK5A20 Table 2c: Inpuata. General Conditions: T A = 25 C, unless T C is specified Input PSS22 PSS242 PSS362 Unit PSK26 PSK246 PSK366 PSK220 PSK2420 PSK3620 Characteristics Conditions min typ max min typ max min typ max V i Operating input voltage I o = 0 I o nom VDC V io min Min. diff. voltage V i V o T C min T C max V i o Undervoltage lock-out I i 0 No load input current I o = 0, V i min V i max ma I inr p Peak value of inrush current V i nom, with option E A C x Input capacitance µf Output set to 5 V with the R-input. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 4 of 20

5 Table 2d: Inpuata. General Conditions: T A = 25 C, unless T C is specified Input PSS29 PSS29 PSS249 Unit PSK22 PSK22 PSK242 Characteristics Conditions min typ max min typ max min typ max V i Operating input voltage I o = 0 I o nom VDC V io min Min. diff. voltage V i V o T C min T C max V i o Undervoltage lock-out I i 0 No load input current I o = 0, V i min V i max ma I inr p Peak value of inrush current V i nom, with option E A C x Input capacitance µf Output set to 5 V with the R-input. 2 Surges up to 56 V for 2 s are allowed (no shutdown). Table 2e: Inpuata. General Conditions: T A = 25 C, unless T C is specified Input PSS369 PSS488 Unit PSK362 PSK482 Characteristics Conditions min typ max min typ max V i Operating input voltage I o = 0 I o nom VDC V io min Min. diff. voltage V i V o T C min T C max 8 0 V i o Undervoltage lock-out I i 0 No load input current I o = 0, V i min V i max ma I inr p Peak value of inrush current V i nom, with option E 6 6 A C x Input capacitance µf Surges up to 56 V for 2 s are allowed (no shutdown). Input Filter and Fuse An input filter and a fuse are incorporated in all converters as standard. The filter reduces emitted electrical noise and prevents oscillations caused by the negative input impedance frequency f i has the following values: v i max = 000 Hz /f i V (or 0 V pp at 00 Hz) Inrush Current Table 3: Input fuses Model Fuse type Size Supplier PSK3E25, PSK5A20, PSK5A25 F 25 A mm Littlefuse PSK220, PSK2420, PSK3620 PSK5A6, PSK26, PSK28 F 20 A PSK246, PSK248, PSK3620 PSS5A2, PSS5A4, F 5 A PSS22, PSK22, PSS24 PSS242, PSK242, PSS244 PSS362, PSK362, PSK366 PSK482 PSS29, PSS249 F 0 A PSS369, PSS489 characteristic of a switched mode regulator. The input fuse protects against fatal defects; see table 3. The maximum permissible additionally superimposed ripple v i of the input voltage (rectifier mode) at a specified input BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 5 of 20 + R ext V i source I inr p Fig. 2 Equivalent input circuit R i C X + JM085a Vo+ Vo Depending on the input source and the input impedance, the inrush current into the converter may reach a high peak value during the switch-on. The inrush current peak value can be determined by following calculation; see also fig. 2: V i source I inr p = (R s ext + R i ) To limit the inrush current, we recommend the choice of the active inrush current limitation circuit, option E. Load

6 Electrical Output Data General Conditions: T A = 25 C, unless T C is specified R control (pin 6) not connected or progammed to V o nom at I o nom Inhibit input (pin 4) connected to Go Sense lines S+ and S connected at female connector Table 3a: Outpuata of PSS models Output PSS5A2 PSS22 PSS22 Unit Characteristics Conditions min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ± ±3 ±4 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 %/K Output set to 5 V with R-input. Table 3b: Outpuata of PSS models. General conditions as per table 3a Output PSS242 PSS244 PSS362 Unit Characteristics Conditions min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±5 ±5 ±8 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 %/K BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 6 of 20

7 Table 3c: Outpuata of PSS models. General conditions as per table 3a Output PSS29 PSS29 PSS249 Unit Characteristics Conditions min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±3 ±4 ±5 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 %/K Output set to 5 V with R-input. Table 3d: Outpuata of PSS models. General conditions as per table 3a Output PSS369 PSS489 Unit Characteristics Conditions min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±5 ±0 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 %/K Table 4a: Outpuata of PSK models. General conditions as per table 3a Output PSK3E25 PSK5A6 PSK5A20 PSK5A25 Unit Characteristics Conditions min typ max min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage Total incl. spikes IEC/EN 6204 noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load Recovery time I o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ± ± ± ± mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 ±0.02 %/K BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 7 of 20

8 Table 4b: Outpuata of PSK models. General conditions as per table 3a Output PSK26 PSK220 PSK26 PSK220 Unit Characteristics Conditions min typ max min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage Total incl. spikes IEC/EN 6204 noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load Recovery time I o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±3 ±3 ±4 ±4 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 ±0.02 %/K Output set to 5 V with R-input. Table 4c: Outpuata of PSK models. General conditions as per table 3a Output PSK246 PSK2420 PSK366 PSK3620 Unit Characteristics Conditions min typ max min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage Total incl. spikes IEC/EN 6204 noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load Recovery time I o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±5 ±5 ±8 ±8 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 ±0.02 %/K Table 4d: Outpuata of PSK models. General conditions as per table 3a Output PSK22 PSK22 PSK242 Unit Characteristics Conditions min typ max min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±3 ±4 ±5 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 ±0.02 %/K Output set to 5 V with R-input BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 8 of 20

9 Table 4e: Outpuata of PSK models. General conditions as per table 3a Output PSK362 PSK482 Unit Characteristics Conditions min typ max min typ max V o Output voltage V i nom, I o nom V I o Output current V i min V i max A I ol Output current limit T C min T C max v o Output Switching freq. V i nom, I o nom mv pp voltage IEC/EN 6204 Total incl. spikes noise BW = 20 MHz V o V Static line regulation V i min V i max, I o nom mv V o l Static load regulation V i nom, I o = 0 I o nom v o d Dynamic Voltage deviat. V i nom load I Recovery time o nom /3 I o nom regulation IEC/EN µs α Vo Temperature coefficient V i min V i max ±5 ±0 mv/k V o / T C (T C min to T C max ) I o = 0 I o nom ±0.02 ±0.02 %/K Output Voltage Regulation The dynamic load regulation is shown in fig. 2 V o /V o nom 05038a V o I o /I o nom V od V o ±% V o ±% V od 0 µs 0 µs Fig. 3 Dynamic load regulation. 0502c Output Protection A voltage suppressor diode, which in worst case conditions fails into a short-circuit, protects the output against an internally generated overvoltage. Such an overvoltage could occur due to a failure of either the control circuit or the switching transistor. The output protection is noesigned to withstand externally applied overvoltages. t t Fig. 4 Overload, short-circuit behaviour V o versus I o. Parallel and Series Connection I o L I o /I o nom Outputs of equal nominal voltage may be parallel-connected. Interconnect the current sharing pins T (pin 22) for even distribution of the output current; see Auxiliary Functions. Outputs can be series-connected with any other regulator, provided that the regulators are powered by electrically isolated source voltages. In series connection the maximum output current is limited by the lowest current limitation. Current Limitation A constant current limitation circuit holds the output current I o almost constant in the area of 00 to 20% of I o nom, when an overload or a short-circuit is applied to the output. It acts selfprotecting and recovers in contrary to the fold back method automatically after removal of the overload or short-circuit condition. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 9 of 20

10 Thermal Considerations and Protection When a switching regulator is located in free, quasi-stationary air (convection cooling) at a temperature T A max and is operated at its nominal output current I o nom, the case temperature T C can rise over T C max after the warm-up phase. T C is measured at the measuring point of case temperature; see Mechanical Data. Under practical operating conditions, the ambient temperature T A may exceed T A max, provided that additional measures (heat I o /I o nom T A min convection cooling 05032a forced cooling C T C max Fig. 5a Output currenerating versus temperature (models -2) T A sink, forced cooling, etc.) are taken to ensure that the case temperature T C does not exceed its maximum value. The regulater is protected by an internal temperature sensor, which inhibits the output above T C max. The output automatically recovers, when the temperature drops below T C max. I o /I o nom T A min convection cooling 0503a forced cooling C T C max Fig. 5b Output currenerating versus temp. (models -7 or -9) T A Auxiliary Functions I inh [ma] Inhibit (Remote On / Off) The inhibit input allows to enable or disable the output with a control signal. In systems with several regulations, this feature can be used to control the activation sequence of the Table 5: Inhibit characteristics Characteristics Conditions min typ max Unit V inh Inhibit input voltage V o = on V i min V i max V V o = off T C min T C max t r Switch-on time V i = V i nom 30 ms t f Switch-off time R L = V o nom /I o nom 25 I i inh Input current when inhibited V i = V i nom 25 ma Vi+ Gi 06009a Vo+ i Go I inh V inh Fig. 6 Specification of the inhibit signal (typical) BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 0 of Output on V inh = 0.8 V V inh = 2.4 V 06034a Output off V Fig. 7 Specification of the inhibit signal (typical) V o /V o nom 0. 0 t t r t f Inhibit Fig. 8 Output response as a function of the inhibit signal t V inh

11 regulators by a logic signal (TTL, C-MOS, etc.). An output voltage overshoot will not occur, when switching on or off. The inhibit signal is referenced to the S (pin 8). The signal i and the switching times are specified in table 5, fig. 6 to 8. Note: With open i input, the output is enabled. Sense Lines This feature enables compensation of the voltage drop across the connector contacts and the load lines. If the sense lines are connected at the load rather than directly at the connector, the user must ensure that V o max (between Vo+ and Go ) is not exceeded. Applying generously dimensioned cross-section load leads reduces the voltage drop. To minimize noise pick-up, the sense lines should be wired in parallel or twisted. To ensure correct operation, both sense lines must be connected to their respective power output. The voltage difference between any sense line and its respective power output pin (as measured on the connector) should not exceed the values given in table 6. Note: Sense lines should always be connected! It is recommended to connect the sense lines directly at the female connector. Table 6: Allowed voltage compensation using sense lines Nominal output Total voltage difference Voltage difference voltage between both sense lines between and their respective output Go and S 3.3 V, 5. V 0.5 V 0.25 V 2 48 V.0 V 0.25 V Vi+ Gi V ref = 2.5 V Fig. 0 Voltage adjustment via R-input + 4 kω Control logic JM54 R Control (Output Voltage Adjust) Note: With open R input, V o V o nom. The output voltage V o can either be adjusted with an external voltage source (V ext ) or with an external resistor (R ext or R ext2 ). The adjustment range is approx. 0 V o max. The minimum differential voltage V io min between input and output (see Electrical Input Data) should be maintained. a) V o = 0 V o max, using V ext between R and S : V o V ext V ext 2.5 V V o V o nom V o nom 2.5 V Caution: To prevenamage V ext should not exceed 20 V, nor be negative. b) V o = 0 to V o nom, using R ext between R and S : 4000 Ω V o V o nom R ext R V o V o nom V o R Ω S+ R S Go R ext2 R ext + V ext Vi+ i R T Gi 06046a Vo+ S+ S Go Load c) V o = V o nom to V o max, using R ext2 between R and S+: 4000 Ω V o (V o nom 2.5 V) R V (Vo Vo nom) V o nom 2.5 V R ext2 V o 2.5 V (R Ω) V o nom 4000 Ω Caution: R ext should never be less than 47 kω. Fig. 9 Sense lines connection Current Sharing For parallel operation of several regulators, interconnect all T- pins to ensure that the output currents are evenly distributed. This feature improves transient load performance and increases system reliability. All paralleled regulators should be supplied by equal input voltage (V i ). The output lines should exhibit equal length and cross section to provide equal voltage drop. Test Sockets Test sockets (pin = 2 mm) for measuring the output voltage V o at the sense lines, are located at the front side of the regulator. The test sockets are protected by a series resistor. LED Output Voltage Indicator A green LED indicator shines when the output voltage is present. Table 7: Maximum adjustable output voltage V o nom Nominal Output Volt. Conditions 3.3 V 5. V 2/5 V 24 V 36 V 48 V Unit min typ min typ min typ min typ min typ min typ V o max Maximum adjustable V i nom, I o nom V output voltage with R-input BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page of 20

12 Electromagnetic Compatibility (EMC) Electromagnetic Immunity General condition: Case not earthed. Table 8: Immunity type tests Phenomenon Standard Class Coupling Value Waveform Source Test In Perf.- Level mode applied imped. procedure oper. crit. 4 Direct transients 2 IEC i/c, +i/ i 800 V p 00 µs 00 Ω pos. and neg. yes B 500 V p 50 µs voltage surge per coupling mode 3000 V p 5 µs 4000 V p µs 7000 V p 00 ns Electrostatic IEC/EN 4 2 contacischarge 8000 V p /50 ns 330 Ω 0 positive and yes A discharge negative air discharge 5000 V p (to case) discharges Electromagnetic IEC/EN 3 2 antenna 0 V/m 2 AM 80% MHz yes A field V/m 3 khz 3 2 antenna 0 V/m 50% duty cycle, n.a. 900 ±5 MHz yes A 200 Hz rep. rate Electrical fast IEC/EN 3 2 i/c, +i/ i 2000 V 2 p bursts of 5/50 ns 50 Ω 60 s positive yes A transients/burst V 3 p 5 khz rep. rate 60 s negative V 2 transients with transients per p V 3 5 ms burst coupling mode p duration and 300 ms period Surges IEC/EN 3 2 i/c 2000 V 2 p.2/50 µs 2 Ω 5 pos. and 5 neg. yes A V 3 p surges per 3 2 +i/ i 2000 V 2 p.2/50 µs 2 Ω coupling mode V 3 p Conducted IEC/EN 3 2 i, o, signal wires 0 VAC 2 AM 80% 50 Ω MHz yes A disturbances VAC 3 khz i = input, o = output, c = case 2 Not applicable for -2 models 3 Valid for -2 models 4 A = Normal operation, no deviation from specifications, B = Normal operation, temporary loss of function or deviation from specs possible 5 With option C, manual reset might be necessary. B 5 BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 2 of 20

13 Electromagnetic Emissions dbµv 80 Limit: 6204bqp Detector: Peak, conducted Vi+, EMC-Service Divina, PSK242-9, U i = 0 Vdc, U o = 24 V, I o = 0 A JM53 EN A qp dbµv/m EMC-Service Divina, ESVS 30:R&S, BBA 906/UHALP 907:Schwarzb., QP, Testdistance 0 m, PSK24Z0A-7EC U i =66 V, U o =24 V I o = 0 A EN 550 A JM52 60 EN A pk MHz MHz Fig. Typical conducted disturbance voltage (quasi-peak and avrage) according to EN 550/22 measured at V i nom = 0 V and I o = 0 A (PSK242-9). Fig. 2 Typ. radiated disturbance voltage (quasi-peak) in 0 m distance according to EN 550/22 measured at V i nom = 0 V and I o = 0 A (PSK242-9). BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 3 of 20

14 Immunity to Environmental Conditions Table 9: Mechanical and climatic stress Test Method Standard Test Conditions Status Cab Damp heat IEC/EN Temperature: 40 ±2 C Regulator steady state MIL-STD-80D section Relative humidity: 93 +2/-3 % not Duration: 56 days operating Db Damp heat test, EN 5055:2007, clause Temperature: 55 C and 25 C Converter cyclic 2 IEC/EN Cycles (respiration effect): 2 not Duration: 2 24 h operating -- Salt mist test EN 5055:2007 Temperature: 35 ±2 C Regulator sodium chloride sect Duration: 6 h not (NaCl) solution class ST2 operating Ea Shock IEC/EN Acceleration amplitude: 50 g n = 490 m/s 2 Regulator (half-sinusoidal) MIL-STD-80D section 56.3 Bump duration: ms operating Number of bumps: 8 (3 each direction) Eb Bump IEC/EN Acceleration amplitude: 25 g n = 245 m/s 2 Regulator (half-sinusoidal) MIL-STD-80D section 56.3 Bump duration: ms operating Number of bumps: 6000 (000 each direction) Fc Vibration IEC/EN Acceleration amplitude: 0.35 mm (0 60 Hz) Regulator (sinusoidal) MIL-STD-80D section g n = 49 m/s 2 ( Hz) operating Frequency ( Oct/min): Hz Tesuration: 7.5 h (2.5 h each axis) Fda Random vibration IEC/EN Acceleration spectral density: 0.05 g 2 /Hz Regulator wide band DIN part 23 Frequency band: Hz operating Reproducibility Acceleration magnitude: 4.9 g n rms high Tesuration: 3 h ( h each axis) -- Shock EN 5055:2007 clause 2.2. Acceleration amplitude: 5. g n Regulator EN 6373 sect. 0, Bump duration: 30 ms operating class B, body mounted Number of bumps: 8 (3 in each direction) -- Simulated long life EN 5055:2007 clause 2.2. Acceleration spectral density: 0.02 g 2 n /Hz Regulator testing at EN 6373 sect. 8 and 9, Frequency band: 5 50 Hz operating increased random class B, body mounted Acceleration magnitude: 0.8 g n rms vibration levels Tesuration: 5 h (5 h in each axis) Body mounted = chassis of a railway coach 2 Models with version V04 or later Temperatures Table 0: Temperature specifications, valid for an air pressure of hpa ( mbar) Temperature -2-7 (Option) -9 Characteristics Conditions min max min max min max Unit T A Ambient temperature Regulator C T C Case temperature operating T S Storage temperature Non operational See Thermal Considerations and Overtemperature Protection. Reliability Table : MTBF and device hours MTBF Ground Benign Ground Fixed Ground Mobile Device Hours MTBF acc. to MIL-HDBK-27F T C = 40 C T C = 40 C T C = 70 C T C = 50 C h h h h h Statistical values, based on an average of 4300 working hours per year and in general field use BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 4 of 20

15 Mechanical Data PSS Models The regulators are designed to be inserted into a rack according to IEC Dimensions in mm. European Projection 7 TE 5 TE to b 4 x M4 LED OK green ± Potentiometer (option P) + Test sockets Measuring point of case temperature T C Front plate Main face 68.5 ±0.5 Back plate 60 d x Screw holes of the frontplate Fig. 3 Case S0 for PSS models; weight.3 kg Aluminum, fully enclosed, black finish EP power-coated, and self cooling. Notes: d 5 mm, recommended minimum distance to next part to ensure proper air circulation at full output power. Free air locations: the regulator should be mounted with its fins in vertical position to achieve a maximum air flow through heat sink. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 5 of 20

16 PSK Models The regulators are designed to be inserted into a DIN-rack according to IEC Dimensions in mm. European Projection TE 9 TE b LED OK green 89 ± Potentiometer (option P) + Test sockets Measuring point of case temperature T C to Front plate Main face Back plate 68.5 d.8 5 x Screw holes of the frontplate Fig. 4 Case K0 for PSK models, weight.6 kg Aluminum, fully enclosed, black finish EP powder-coated, and self cooling. Notes: d 5 mm, recommended minimum distance to next part to ensure proper air circulation at full output power. Free air locations: the regulator should be mounted with its fins in vertical position to achieve a maximum air flow through heat sink. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 6 of 20

17 Option B, B European Projection ± Fig. 5 Option B, large cooling plate Weight:.3 kg M ± Fig. 6 Option B, small cooling plate Weight:.2 kg BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 7 of 20

18 Safety and Installation Instructions Connector Pin Allocation The connector pin allocation table defines the electrical potentials and the physical pin positions on the H5 or H5S4 connector. Pin 24 (protective earth) is a leading pin, which provides electrical contact first. The regulators should only be wired via the female connector H5 (according to DIN 462) to ensure requested safety! 32 30/32 Fixtures for connector retention clips V (see Accessories) Type H5 Fixtures for connector retention clips V (see Accessories) Type H5S4 Fig. 7 View of H5 and H5S4 male connector 000a 4 4/6 Installation Instruction Installation of the regulators must strictly follow the national safety regulations in compliance with the enclosure, mounting, creepage, clearance, casualty, markings, and segregation requirements of the end-use application. The input and the output circuit are not separated. The negative path is internally interconnected. The regulators should be connected to a secondary circuit. Make sure that a regulator failure (e.g. by an internal shortcircuit) does not result in a hazardous condition. Do not open the regulator! Standards and Approvals The regulators are safety-approved to UL/CSA nd Ed. and IEC/EN nd Ed. They correspond to Class I equipment (with case connected to ground). The regulators have been evaluated for: Building in No insulation from input to output. The use in a pollution degree 2 environment Connecting the input to a secondary circuit, which is subject to a maximum transient rating of 500 V. The switching regulators are subject to manufacturing surveillance in accordance with the above mentioned standards and with ISO 900:2008. Cleaning Liquids In order to avoid possible damage, any penetration of cleaning fluids must be prevented, since the regulators are not hermetically sealed. Table 2: H5 and H5S4 connector pin allocation Electrical Determination Type H5 Type H5S4 Pin no. Ident. Pin no. Ident. Output voltage (positive) 4 Vo+ Output voltage (positive) 6 Vo+ 4/6 Vo+ Output voltage (negative) 8 Go Output voltage (negative) 0 Go 8/0 Go Crowbar trigger input (option C) 2 C 2 C Inhibit input 4 i 4 i R-input (output voltage programming) 6 R 6 R Sense line (negative) 8 S 8 S Sense line (positive) 20 S+ 20 S+ Current sharing control input 22 T 22 T Protective ground (leading pin) Input voltage (negative) 26 Gi Input voltage (negative) 28 Gi 26/28 Gi Input voltage (positive) 30 Vi+ Input voltage (positive) 32 Vi+ 30/32 Vi+ Not connected with option P Protection Degree The protection degree is IP 30 (IP 20, if equipped with option P). It applies only, if the regulator is plugged-in or the matching female connector is properly attached. Isolation and Protective Earth The resistance of the protective earth connection (max. 0. Ω) is tested. The electric strength between input interconnected with output and case is tested with 500 VDC s (all models with version V03 or later). Models with V i max = 44 V and V04 or later are tested with 2200 VDC s. These tests are performed in the factory as routine test in accordance with EN 506 and IEC/EN The electric strength test should not be repeated by the customer. BelPS Company does not honor warranty claims resulting from incorrect electric strength tests. Railway Application The regulators have been developed observing the railway standards EN 5055 and EN 502. All boards are coated with a protective lacquer. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 8 of 20

19 Description of Options Î [A] 029a -7 Temperature Range This option defines a restricted temperature range as specified in table 0 (not for new designs). Inrush limit V (I i = ) i R s Soft start Normal operation (R s bypassed) P Potentiometer to Adjust the Output Note: Option P is not recommended for regulators operated in parallel connection. Option P excludes the R function; the R-input (pin 6) should be left open-circuit. The output voltage V o can be adjusted in the range 90 0% of V o nom. However, the minimum differential voltage V i max between input and output as specified in Electrical Input Data should be respected. E Inrush Current Limitation Note: This option requires an increased minimum input voltage V i max of up to V, dependent upon input range. In regulators without option E, after application of the input supply the inrush current is limited by parasitic components of the voltage source and the regulator input only. The regulator input exhibits a very low impedance, and when driven from a low impedance source, for example a battery, the inrush current can peak at several orders of magnitude above the continuous input current. Option E dramatically reduces this peak current and is recommended for any application to protect series elements such as fuses, switches, or circuit brakers. The start-up circuit is bypassed during normal operation. C Thyristor Crowbar Note: The crowbar can be reset by removal of the input voltage only. The inhibit signal cannoeactivate the thyristor. Option C protects the load against power supply malfunction. It is noesigned to sink external currents. As a central overvoltage protection device, the crowbar is usually connected to the external load via distributed inductance of the lines. For this reason, the overvoltage at the load can temporarily exceed the trigger voltage V o c. Depending on the application, further decentralized overvoltage protection elements may have to be used additionally. Fig. 8 Option E: Inrush current versus time. R s is the startup resistor (R s = Ω for models with V i max 80 V, R s = 5 Ω for models with V i max > 80 V) A fixed-value monitoring circuit checks the output voltage V o, and when the trigger voltage V o c is reached, the thyristor crowbar triggers and disables the output. An external connection C (crowbar trigger control) is provided. When crowbar option is used with two or more power supplies in parallel connection, all crowbar trigger terminals (C) should be interconnected. This ensures all crowbar circuits triggering simultaneously, in order to disable all outputs at once. The crowbar trigger voltage is maintained between Vo+ and Go. To prevent false triggering, the user should ensure that V o (between Vo+ and Go ) deos not exceed V o c. B, B Cooling Plate Where a cooling surface is available, a cooling plate (option B or option B) can be fitted instead of the standard heatsink. The mounting system must ensure sufficient cooling capacity to guarantee that the maximum case temperature T C max is not exceeded. The required cooling capacity can be calculated by the following formula: 00% η P Loss = - (V o I o ) η G t 0 40 (typical) 00 (typical) ms RoHS Compliance Models with G are RoHS-compliant for all six substances. Table 3: Crowbar trigger levels Characteristics Conditions PSK5A6 PSK22 PSS249 PSK362 PSK482 Unit PSK5A20 PSK26 PSK242 PSK366 PSK5A25 PSK220 PSK246 PSK3620 PSK2420 min typ max min typ max min typ max min typ max min typ max V o c Trigger voltage T C min T C max V V i min V i max Delay time I o = 0 I o nom µs t s Models with option P BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 9 of 20

20 Accessories A variety of electrical and mechanical accessories are available including: Various front panels for 9" DIN-racks with 3U heigth, 2 or 6 TE, Schroff or Intermas Various mating connectors H5 and H5S4 including faston, screw, solder, or press-fit terminals, code key system and coding wedges HZZ00202-G Pair of connector retention clips HZZ0209-G; see fig. 20 Connector retention brackets HZZ026-G; see fig. 22 Different cable connector housings (cable hoods), including a metallic version for fire protection Cage clamp adapter HZZ0044-G; see fig. 23 Wall-mounting plate K02 HZZ023, only for models with option B Brackets for DIN-rail and wall mounting HZZ0060 DIN-rail mounting assembly HZZ065-G; see fig. 24 Battery sensors S-KSMH... for using the converter as battery charger. Different cell characteristics can be selected; see Battery Charging/ Temperature Sensor. For additional accessory product information, see the accessory data sheet listed with each product series or individual model listing at our web site. 20 to 30 Ncm Fig. 22 Connector retention brackets HZZ026-G Fig. 23 Cage clamp adapter HZZ0044-G Fig. 9 H5 female connector with code key system Fig. 20 Connector retention clips HZZ0209-G Fig. 2 Different front panels Fig. 24 DIN-rail mounting assembly HZZ065-G NUCLEAR AND MEDICAL APPLICATIONS - These products are noesigned or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. BCD20029-G Rev AC, 2-Jan-205 The Power Partners. Page 20 of 20