MAGNETIC-LATCHING DC-8 GHz TO-5 RELAYS 4PST

Size: px

Start display at page:

Download "MAGNETIC-LATCHING DC-8 GHz TO-5 RELAYS 4PST"

Marcia Merritt
6 years ago
Views:

MagneticLatching Electromechanical Relay MAGNETICLATCHING DC8 GHz TO5 RELAYS PST SERIES SGRF SGRFD RELAY TYPE PST RF Relay PST RF Relay with internal diodes for coil transient suppression DESCRIPTION

It s low profi le and small size make it ideal for applications where extreme packaging density and/or close PC board spacing are required.

1 MagneticLatching Electromechanical Relay MAGNETICLATCHING DC8 GHz TO5 RELAYS PST SERIES SGRF SGRFD RELAY TYPE PST RF Relay PST RF Relay with internal diodes for coil transient suppression DESCRIPTION The RF series relay is an ultraminiature, hermetically sealed, magneticlatching relay featuring low intercontact capacitance for exceptional RF performance from DC8 GHz. It s low profi le and small size make it ideal for applications where extreme packaging density and/or close PC board spacing are required. Due to its minimal mass, many relays may be used to confi gure replacements for bulkier switching solutions at a substantial savings in weight.these design features make these unique relays the perfect choice for use in RF attenuators, RF switching matrices and other RF applications requiring low insertion loss and low VSWR. The basic operating mechanism is similar to the TO5 series relay. The following unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to environmental extremes: Minimum mass components and welded construction provide maximum resistance to shock and vibration. Advanced cleaning techniques provide maximum assurance of internal cleanliness. Goldplated precious metal contacts ensure reliable, lowlevel switching. The RF relay is ideally suited for applications where power dissipation must be minimized. The relays can be operated with a short duration pulse. After the contacts have transferred, no external holding power is required. The magnetic latching feature of the RF series provides a nonvolatile memory capability since the relays will not reset upon removal of coil power. The D series utilizes discrete diodes for coil suppression. PRINCIPAL OF OPERATION Energizing Coil B produces a magnetic field opposing the holding fl ux of the permanent magnet in Circuit B. As this net holding force decreases, the attractive force in the air gap of Circuit A, which also results from the fl ux of the permanent magnet, becomes great enough to break the armature free of Core B, and snap it into a closed PERMANENT MAGNET MAGNETIC CIRCUIT B ARMATURE position against Core A. The armature then remains in this position upon removal of power from Coil B, but will snap back into position B upon energizing Coil A. Since operation depends upon cancellation of a magnetic fi eld, it is necessary to apply the correct polarity to the relay coils as indicated on the relay schematic. When latching relays are installed in equipment, the latch and reset coils should not be pulsed simultaneously. Coils should not be pulsed with less than rated coil voltage and the pulse width should be a minimum of three times the specifi ed operate time of the relay. If these conditions are not followed, it is possible for the relay to be in the magnetic neutral position. + MAGNETIC CIRCUIT A FRAME + AIR GAP STATIONARY CONTACT MOVING CONTACT ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Temperature Storage Operating Vibration (General Note ) Shock (General Note ) Enclosure Weight 65 C to +5 C 55 C to +85 C 0 g s to 500 Hz 0 g s, for 6 msec half sine Hermetically Sealed 0. oz. (.9g) max. 0 TELEDYNE RELAYS (800) SGRF Page SGRF\060\Q

2 MagneticLatching Electromechanical Relay SERIES SGRF/SGRFD TYPICAL RF CHARACTERISTICS (See RF Notes) Isolation Across Contacts (RF Note ) Isolation Pole to Pole (RF Note 5) Isolation ( db ) Isolation ( db ) Path: or 89 Path: or Path: or 89 Path: or Insertion Loss (RF Note 6) VSWR (RF Note 6) Path: or 89 Path: or 67 Insertion Loss ( db ) VSWR Path: or 89 Path: or RF NOTES. Test conditions: a. Fixture:.0" copper clad, reinforced PTFE, RT/duroid 600 with SMA connectors. (RT/duroid is a registered trademark of Rogers Corporation.) b. Relay header is soldered to ground plane. c. Room ambient temperature. d. All terminals not tested were terminated with 50ohm load. e. Contact signal level: 0 dbm. f. No. of test samples:.. Data presented herein represents typical characteristics and is not intended for use as specification limits.. Data is per pole, except for poletopole data.. Data is the average from readings taken on poles after Coil A is energized then Coil B is energized. 5. Data is the average from readings taken on all closed contacts. 6. Test fixture effect deembedded from frequency and time response data. SGRF Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 0 TELEDYNE RELAYS SGRF\060\Q

3 MagneticLatching Electromechanical Relay SERIES SGRFA/SGRFD GENERAL ELECTRICAL SPECIFICATIONS C unless otherwise noted) (Note ) Contact Arrangement Rated Duty Contact Resistance Contact Load Rating Contact Life Ratings Coil Operating Power Operate Time Contact Bounce Intercontact Capacitance Insulation Resistance Dielectric Strength Negative Coil Transient (Vdc) Diode P.I.V. (Vdc) BiStable (PST) Continuous 0.5 Ω max. initial (measured /8" from the header) Resistive: Amp/8Vdc Low level: 0 to 50 0 to 50 mv 0,000,000 cycles (typical) at low level 00,000 cycles min. at all other loads specifi ed above RF5: 0 mw nominal rated voltage RF: 88 mw nominal rated voltage RF6: 5 mw nominal rated voltage.5 ms nominal rated voltage.0 ms max. 0. pf typical 0,000 MΩ min. between mutually isolated terminals 50 Vrms (60 atmospheric pressure 5 Vrms (60 70,000 ft RFD:.0 max. RFD: 00 min. DETAILED ELECTRICAL SPECIFICATIONS (@5 C) BASE PART NUMBERS SGRF5 SGRFD5 SGRF SGRFD SGRF6 SGRFD6 Coil Voltage, Nominal (Vdc) Nom Max Coil Resistance (Ohms 5 C) (Note ) Set & Reset Voltage (Vdc, Max.) Pulse Operated Teledyne Part Numbering System for SGRF Relay Series D= Internal diode for transient suppression Nominal Coil Voltage SGRFD 5 / S Q Q = Solder Coated Leads G = Gold Plated Leads (RoHS Compliant) R = RoHS Compliant Solder S = 0.87 Leads W =.5 Leads No Suffi x = 0.75 Leads General Note: Parts ordered without suffix may be supplied with SolderCoated or GoldPlated leads Parts ordered with SolderCoated leads will have (Sn60/Pb0) Parts ordered with RoHS SolderCoated leads will have (Sn99./Cu0.7) 0 TELEDYNE RELAYS (800) SGRF Page SGRF\060\Q

4 MagneticLatching Electromechanical Relay SERIES SGRF/SGRFD OUTLINE DIMENSIONS SGRFD SCHEMATIC (Coil B Last Energized) (Bottom View) SGRFD NOTES:. DIMENSIONS ARE IN INCHES, METRIC EQUIVALENTS SHOWN IN [ ]. SCHEMATIC (Coil B Last Energized) (Bottom View) GENERAL NOTES. Relays will exhibit no contact chatter in excess of 0 μsec or transfer in excess of μsec.. Unless otherwise specified, parameters are initial values.. For extended contact life ratings, contact factory.. Contacts shown in position resulting when Coil B last energized. SGRF Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 0 TELEDYNE RELAYS SGRF\060\Q

MagneticLatching Electromechanical Relay SERIES SGRF/SGRFD TYPICAL SIGNAL INTEGRITY CHARACTERISTICS Typical Path +50 mv 0 V 50 mv 0 ps 0 ps 80 ps 0 ps 60 ps Eye Height Eye Width SNR Jitter PP 5.

5 MagneticLatching Electromechanical Relay SERIES SGRF/SGRFD TYPICAL SIGNAL INTEGRITY CHARACTERISTICS Typical Path +50 mv 0 V 50 mv 0 ps 0 ps 80 ps 0 ps 60 ps Eye Height Eye Width SNR Jitter PP 5.0 mv 90.7 ps ps PATTERN GENERATOR SETTINGS 0 Gbps Random Pulse Pattern Generator PRBS signal PRBS output of 00 mv PP (nominal) RF PCB effect (negligible) not removed from measurement Data shown is typical of both poles 0 TELEDYNE RELAYS (800) SGRF Page 5 SGRF\060\Q

HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT

HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT HIGH REPEATABILITY, DC-8 GHz/Gbps TO-5 RELAYS, DPDT SERIES RELAY TYPE RF3 RF33 Repeatable, RF relay Low Power Operating Coil, RF relay DESCRIPTION The ultra miniature RF3 is designed to improve upon the