SPECIFICATION. Product Name : TheStripe Penta-band GSM 850/900/1800/1900 & UMTS/WCDMA 2100 MHz 80mm*30mm PCB Antenna for Murata GSC Connections

Transcription

1 SPECIFICATION Part No. : PC Product Name : TheStripe Penta-band GSM 850/900/1800/1900 & UMTS/WCDMA 2100 MHz 80mm*30mm PCB Antenna for Murata GSC Connections Features : 119mm long, 0.81mm diameter Miniature Co-axial Cable Murata GSC (Compatible) Connector Tested in Freespace ROHS Compliant REVISION STATUS Photo : Version Date Page Revision Description Prepared Approved 01 May 24 th 2007 All New format TW Product Centre Ronan Quinlan

2 Contents 1.0 Introduction Key Antenna Performance Indicators Mechanical Specifications Placement Electrical Characteristics Charts Environmental Conditions and Reliability Test Setup and Detailed Results Packaging Cable and Connector Drawings 20

3 1.0 Introduction This high performance, low profile, PCB antenna is based on smart TheStripe antenna technology. It consists of a PCB antenna and mini coaxial cable. The product is a high gain Penta-band 850/900/1800/1900/2100 antenna suitable for worldwide GSM, UMTS and WCDMA applications. The product should be tested in freespace conditions connected to the client s cellular device. It is designed for connection to Murata GSC receptacles. Further optimization can be done upon receipt of the client s device at a local Taoglas facility. 2.0 Key Antenna Performance Indicators Taoglas PC Communication System Frequency Band (MHz) AMPS GSM DCS PCS UMTS/WCDMA VSWR Return Loss Efficiency 9% 13% 25% 67% 76% 65% 80% 59% 55% 2.6 Peak Gain (dbi) Average Gain Impedance 50 Ohm 2.9 Radiation Pattern Omni-directional 2.10 Polarization Linear

4 3.0 Mechanical Specifications 3.1 Dimensions and Drawing 3.2 Cable and Connector RF Coaxial Cable ψ0.81 ± 0.1mm RF Cable L = 119 mm Gray Colour RF Connector Murata GSC (compatible) 4.0 Antenna Placement Antenna designed to for testing when connected outside the client s device and placed in freespace conditions, for example on plastic foam block. Final product can use pre-applied double sided adhesive tape, slot or screwmount

5 5.0 Antenna Electrical Characteristics 5.1 Return Loss

6 5.2 VSWR

7 6.0 Environmental Conditions and Reliability 6.1 Environmental Conditions Operation Temperature -20 C to + 65 C Storage Temperature -30 C to + 75 C Relative Humidity 40% to 95% 6.2 Reliability Test Items Procedure Requirement Thermal Shock Storage Temperature (Cold) Starting at -40 for 30minutes and then cycled to +85 to remain 30minutes (a complete cycle). To repeat 5 complete cycles. (Refer to IEC Method Na) Samples must be put into -30 C chamber for 72 hours and samples shall be powered during test. (Refer to IEC Method Aa) 1. The value of return loss must be within product specifications after this test. 2. No physical deformation should be evident. 1. The value of return loss must be within product specifications after this test. 2. No physical deformation should be evident. Storage Temperature (Dry Heat) Samples must be put into +75 C chamber for 72 hours and samples shall be powered during test. (Refer to IEC Method Ba) 1. The value of return loss must be within product specifications after this test. 2. No physical deformation should be evident. Operating Temperature (Cold) Samples must be put into -20 C chamber for 2 hours and samples shall be powered during test. (Refer to IEC Method Aa) 1. The value of return loss must met specification during test/after test 2. No mechanical defects after test. Operating Temperature (Dry Heat) Samples must be put into +65 C chamber for 72 hours and samples shall be powered during test. (Refer to IEC Method Ba) 1. The value of return loss must met specification during test/after test 2. no mechanical defects after test.

8 7.0 Antenna Test Procedures and Setup 7.1 Test Procedure for VSWR/Return Loss STEP 1 Route Cable in Correct Position STEP 2 Connect Antenna to Module Connect feed-line to network analyzer STEP 3 Assemble Antenna in Correct Position on Isolated Foam Block

9 7.2 3D Radiation Pattern Testing Test Setup Diagram Actual Test Photo

10 Standard Horn Antenna PC (DUT) D Radiation Patterns Azimuth plane 824MHz Elevation plane 824MHz

11 Azimuth plane 850MHz Elevation plane 850MHz 4

12 Azimuth plane 900MHz Elevation plane 900MHz

13 Azimuth plane 1710MHz Elevation plane 1710MHz

14 Azimuth plane 1800MHz Elevation plane 1800MHz Azimuth plane 1900MHz Elevation plane 1900MHz 6

15 Azimuth plane 1990MHz Elevation plane 1990MHz Azimuth plane 2100MHz Elevation plane 2100MHz

16 Azimuth plane 2170MHz Elevation plane 2170MHz D CHAMBER TESTING TABULAR RESULTS PC

17

18 7.2.5 Gain vs Frequency Chart Gain(dBi) Gain(dBi) Frequency(MHz) Gain (dbi) Average Gain (db) Efficiency vs Frequency Chart Efficiency (%) 100 Efficiency(%) Efficiency (%) Frequency(MHz)

19 8.0 Antenna Packaging

20 9.0 Cable and Connector Drawings 0.81mm Outside Diameter Cable Specification

21 Murata GSC Connector (Compatible)