The Low-Noise, Integrated Transformer Helium-4 Dipstick Insert
|
|
- Morgan Charles
- 6 years ago
- Views:
Transcription
1 The Low-Noise, Integrated Transformer Helium-4 Dipstick Insert Sang Lin Chu Georgia Institute Of Technology 837 State Street N.W. Atlanta, GA December 29, 2003
2 1 Introduction The low-noise dipstick with an integrated low temperature transformer was designed in the summer of 2003 from June to early August by Sang Chu and Alexey Bezryadin as part of a summer research project for the Research Experience for Undergraduates at the University of Illinois at Urbana-Champaign. The intent of developing such a Helium-4 insert, or dipstick, was to measure very low resistances with a low noise floor much better than the previous implementation which had a noise floor of a few Ohms (microvolt and nanoamp resolution driving signals). There are three stages of filters on all lines in the dipstick. The first consists of a compacted stainless steel powder filter, the second of Thermocoaxial MgO powder filter cables, and the third of silver-paste applied to the insulation of thin copper wires directly connected to a 16 pin chip carrier. The bottom of the dipstick where the sample is connected is enclosed by an electromagnetic shield of copper. The transformer is also inside the same copper cell. The transformer setup was designed so that the dipstick could be used with or without the transformer in measurements. The dipstick can achieve a base temperature of 1.45 K when pumped inside a Helium-4 dewar. Ideal usage is for temperatures below 77 K due to ground leaks from the thermocoaxial cables. 2 Vacuum Design The highest part of the dipstick consists of Quick-Flange type fittings. Most of it is comprised of QF-40 sized flanges. A Fischer brand receptacle (part number DBEE-105A pin) is mounted on a blank QF-40 flange machined to form a vacuum seal using the supplied o-rings on the receptacle. The low temperature part of the dipstick is sealed forming a vacuum connection with a 1.5 nominal outer diameter stainless steel 316 tube with a welded QF-50 fitting. A small vacuum valve used for pumping and insertion of Helium-4 exchange gas uses QF-16 quick flange fittings. The inner tube is a thin walled 1/2 outer diameter stainless steel tube attached to the center of the vacuum assembly by 5/8 compression fittings connected to a 3/8 male pipe thread extension. A picture of the top portion of the vacuum assembly is shown with the BNC box connected to the Fischer connector receptacle. 3 Electrical Wiring and Filtering All measurement leads are connected at room temperature with female BNC panel mount connectors contained inside an aluminum project box. The BNC box is fitted with the matching female mating connector to the Fischer receptacle (Fischer part number S105A pin female plug). The female plug had to be 2
3 modified to be mounted inside the project box as it is normally used in cable assemblies and not for panel mount installations. From the Fischer connector receptacle, we use Lakeshore low temperature quad twisted pair (part number Quad-Twist Cryogenic Wire QT36) wires which have two pairs of twisted pair leads. These are ideal for low interference four probe measurements. The wires are made of non-ferromagnetic 36 AWG phosphor bronze wire with Formvar insulation and are quite easy to solder. These wires then go straight into the compact powder filters using the ends of an old-style resistor to fit tightly into the female receptacle of the SMA connector (note that the resistors were later removed and the wires were directly connected to the filters). More information on the compact powder filters can be found in the document titled Compact Powder Filters. Each compact powder filter is labeled with numbers corresponding to the pin numbers on the Fischer connector. From the compact powder filters, thermocoaxial cables using SMA connectors are connected. The thermocoaxial cables have 34 AWG enamel coated insulated copper wires which go inside the copper cell through silver paste and directly to the chip holder. More information on assembly and filtering characteristics on the thermocoaxial cables can be found in the document Thermocoaxial Cables as a Low Temperature High Frequency Filter. The following picture shows the connections from the twisted pair wires to the low temperature parts of the dipstick. The sample chip mount is a 16 pin integrated chip carrier with a slight notch on the upper left-hand corner to indicate pin 1. Two pins, labeled by an X, are not used and covered by the use of a Cernox X2024 thermometer (calibration was made in the LabVIEW file Cernox R to T X20424.vi). The pin layout of the chip carrier is labeled in the diagram below. The pin numbers correspond to the Fischer receptacle connector (part number DBEE105A pin) used at the room temperature part of the dipstick. Twisted pairs are denoted by arrows connecting them. 3
4 The input of the transformer is connected on pins 12 and 13. A counterwound heater made of Stablohm resistive wires is connected on pins 20 and 21 with an end to end resistance of 573 Ω. The following table summarizes the resistance from room temperature BNC connectors to the pins on the chip carrier for each pin. The compact powder filters contribute anywhere from Ω due to contact resistance and the Advance wire inside whereas the thermocoaxial cables contribute Ω due to contact resistance and Nickel-Chrome (80/20) inner conductor. Room temperature leakages (as measured on August 9th, 2003) are also reported. Note that the leakages disappear when cooled near Nitrogen (77 K) temperature. Naturally, there is an associated error with measurement at room temperature on the order of mega-ohms due to this leakage. It is suggested to keep the dipstick under vacuum while not in use to prevent further leakage due to water absorption of the thermocoaxial cables. Resistances were measured with a Keithley 187 True RMS multimeter. 4 Transformer The basic concept behind the transformer is to use an inductively coupled setup so that the signal is amplified by a high turn ratio between the pickup loop and the sample. The following circuit diagram shows the wiring of a typical sample when connected to the transformer. R s denotes the sample resistance, R z the impedance of the transformer, G the gain of the transformer and V the voltage source driving the current I through the sample and transformer connected in parallel. 4
5 Pin Lead Resistance [Ω] Ground Leak Resistance (300 K) [M Ω] Overload > Overload Overload > Overload > Overload > > > > Heater + > Heater - > > >4.95 Table 1: End-to-end resistances (from RT to the base temperature chip holder). The transformer has four primaries primaries P1, P2 is on the yellow/red cable while primaries P3, P4 are on the yellow cable. The secondary S is on the red cable and is used to connect directly to room temperature electronics. The table below summarizes the gains, resistances and nominal turn ratios for each primary as measured at room temperature. At a temperature of 4 K, the resistances of the copper windings of the transformer are expected to be approximately 70 times smaller. Pins 12 and 13 from the chip carrier have a 4 pin removable connector which can be connected to the transformer or directly to the room temperature connections. When connected to the transformer, alignment of the black line on the connected to the yellow/red transformer cable results in a connection to primary P1. Rotation by 180 degrees results in connection to primary P2. Alignment of the black line on the yellow transformer cable results in a connection to primary P3 and similarly, a rotation of 180 degrees results in a connection to primary P4. The table below summarizes the connections to the transformer. The following diagram shows how the connections on the transformer were made. 5
6 Primary Nominal Turns Resistance [Ω] (300 K) Turn Ratio 3V 1 khz on S P : mv P : mv P : mv P : mv S Table 2: Summary of the transformation gains, turn ratios and resistances. Primary P1 P2 P3 P4 Alignment with Black Marker on Connector Aligned with black marker on yellow/red cable from transformer Anti-aligned with black marker on yellow/red cable from transformer Aligned with black marker on yellow cable from transformer Anti-aligned with black marker on yellow cable from transformer Table 3: Wiring chart for the transformer. 6
UHV Double-Ended SMA Feedthrough, , Conflat compatible flange
SMA Interface SMA Interface Grounded and Feedthroughs UHV Double-Ended SMA Feedthrough, 110730, Conflat compatible flange UHV male SMA cable 5 assembly, 110755, Kapton insulated 50-ohm coaxial cable Features
More informationAmphenol RF. Mini-BNC Mini-BNC Connectors. Mini-BNC. Description. Features/Benefits. Applications
Amphenol RF 100 Connectors Description Amphenol RF introduces the new generation of quality BNC connectors for the telecommunication and broadband applications for higher connector densities while preserving
More informationAmphenol RF- BNC Connector Series
Page 1 of 7 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC
More informationADVANCED GROUP. Pee-Series Series 12 KVDC. Introduction. Introduction
Introduction Introduction Pee-Wee is a series of subminiature, high voltage connectors and cable assemblies for use in high voltage applications where dense electronic packaging is required. Pee-Wee uses
More informationProduct Information Measuring resistor with the Pt100-sensor referring to DIN EN Pt100, Pt500, Pt1000
Platinum sensor probe - Basic information The Pt100-sensor is used for precise temperature monitoring applications, where errors in measurement have to be excluded. The linear relationship of the resistor
More informationDiseño del Criostato del Receptor de Banda Ancha
Diseño del Criostato del Receptor de Banda Ancha José Manuel Serna, Beatriz Vaquero, Félix Tercero, Samuel López Informe Técnico IT-CDT 2015-18 [Los desarrollos descritos en este informe técnico han sido
More informationMaximum mated height 1.2mm, Micro Coaxial Connector K.FL2 Series
Connector mated condition Mated height comparison (compared to conventional company products) Fig.1 Features 1. A low mated height of 1.2mm max. When connected, K.FL2 delivers a world class low mated height
More informationph or ORP Transmitter
ph or ORP Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma (Process + Temp) Removable backlighted display Universal process connection Compatible with 120 mm ph/ ORP probes
More information242, , FAX.
TEL. 886 2 8994 1601, FAX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information SMA SMB Subminiature Connectors Screw Lock Subminiature Connectors Snap Lock 50 Ω 18 GHz
More informationSERIESN50, COAXIAL CONNECTORS
SERIESN50, COAXIAL CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER N connectors are available with 50 and 75 impedance. The frequency range extends to 18 GHz, depending on the connector and cable type.
More informationMicro-Change. Cordset Family
Side Tab Cordset Family Small Space? Big Solution. When space and time are in short supply, look no further than Brad Harrison brand for the best, ready-made m connector solutions. For fast, compact migration
More informationRFX. Type N RG58, 141, 142 Straight Plug Type N Connectors» Cable Straight. Jack 50 Ohm Yes
Please note: Images are for reference only Amphenol Part Number: Description: Product Series: Product Type: Connector Body Style: Gender: Impedance: RoHS Compliant: 082-5376-RFX RG58, 141, 142 Straight
More informationConductivity Transmitter
Conductivity Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma Removable backlighted display Universal process connection Type can be combined with... Three cell constants
More informationSTANDARD RTD's INDEX
STANDARD RTD's INDEX PAGE General Information... R2 Temperature/Resistance Table... R6 Part Numbering Examples... R10 High Temperature MgO Elements (RA)... R11 Leadwire Style RTD's (RB)... R12 Leadwire
More informationQUICK REFERENCE. A-Size (7/8 ) powerfast. D-Size (1 3/8 ) powerfast. M16 powerfast. M23 powerfast. M40 powerfast. 3 & 4 pole 14 AWG conductors
QUICK REFERENCE A-Size (7/8 ) powerfast D-Size (1 3/8 ) powerfast M16 powerfast 3 & 4 pole 14 AWG conductors Tray rated-exposed run PVC cable STOOW cable available Up to 15 Amp, 600 Volt rated NEMA 1,3,4,6P
More informationDigital flow ELEMENT transmitter for continuous flow measurement
ELEMENT Transmitter Digital flow ELEMENT transmitter for continuous flow measurement Type can be combined with... PN10, DN15 to DN400 fluidic process connection Programmable outputs : one or two transistor
More informationAmphenol RF Interconnects BNC 31 Series Bayonet Lock RF Connector System
BNC 31 Series Bayonet Lock RF Connector System Materials Body/Finish /Nickel Centre MALE Centre FEMALE Phosphor Bronze Centre Finish Gold 30µ Insulator Delron/PBT Gasket Silicone Rubber Crimp s Annealed
More informationTNC SERIES General... 4 Interface... 5 Characteristics...6-7
CONTENTS PAGE TNC SERIES General... 4 Interface... 5 Characteristics...6-7 TNC 50 Ω SERIES Plugs...8-9 Jacks...0- Jacks and receptacles... Receptacles...-4 Adapters... 5 Caps... 6 TNC 75 Ω SERIES Plugs...
More informationTimes Microwave Systems Hermetically Sealed Assemblies
SCOPE This Specification details the Electrical, Mechanical and Environmental Characteristics of Times Microwave Systems MILTECH 480.48 Diameter Hermetically Sealed Coaxial Transmission Lines. This product
More informationSTANDARD COAXIAL CONNECTORS. Eco 7/16 series
STANDARD COAXIAL CONNECTORS Eco 7/16 series Eco 7/16 INTRODUCTION GENERAL Standard coaxial connectors Screw on coupling Compliant to CECC and IEC standards 50 Ω APPLICATIONS Broadcast RF components (filters,
More informationSimplex Baseboard System Baseboard System
Simplex Baseboard System Baseboard System I Complete installation programme I Trouble-free and time-saving installation I Various connection kits for all types of pipe Our service to you I Simplex Products
More informationUHV Feedthrough, Conflat compatible flange
NC Interface NC Interface Grounded and Feedthroughs UHV Feedthrough, 110116 Conflat compatible flange UHV female cable 4 assembly, 110180, stainless steel Accufast connector and Kapton insulated coaxial
More informationTorque Sensor Accessories and Services
------------------- Torque Sensor Accessories and Services Highlights Strain gage signal conditioners Cable assemblies Speed sensors Shunt calibration modules and thermocouples Calibration services PCB
More informationsealed mini usb connectors
QUICK CONNECT CABLE END MATES WITH PANEL MOUNT PANEL MOUNT MATES WITH CABLE END REAR VIEW - PC TAIL REAR VIEW - FEED-THRU TERMINATION REAR VIEW - SOLDER HOLES SPECIFICATIONS Mechanical Specifications Life:
More informationLabs. Introduction. Specialty Family
INC. Labs Introduction Specialty Family Features K-Jumper: Affordable, High Performance Interconnect up to 35 GHz Space-Flex : Semi-Rigid and Flexible Cable Assemblies for S-Level Space T-Flex : Flexible
More informationA short, off-center fed dipole for 40 m and 20 m by Daniel Marks, KW4TI
A short, off-center fed dipole for 40 m and 20 m by Daniel Marks, KW4TI Version 2017-Nov-7 Abstract: This antenna is a 20 to 25 foot long (6.0 m to 7.6 m) off-center fed dipole antenna for the 20 m and
More informationDigital flow ELEMENT transmitter for continuous flow measurement
Digital flow ELEMENT transmitter for continuous flow measurement Type 8036 can be combined with... DN06 to DN65 fluidic process connection Programmable outputs : one or two transistor output(s) and single
More informationSmall-sized, plastic type, push-pull lock connectors
Small-sized, plastic type, push-pull lock connectors RP17 Series Product Specifications Ratings Rated current Rated voltage Features 1. Superior mating operability Secure mating and easy unmating is achieved
More informationMineral-insulated resistance thermometers to EN
Data Sheet 90.2221 Page 1/6 Mineral-insulated resistance thermometers to EN 60 751 for temperatures from -50 (-200) to +600 C flexible sheath with shock-protected sensor as single or twin resistance thermometer
More informationSMA - 50 Ohm Connectors
For Flexible Cable Straight Crimp Type Plug - Captivated Contact CABLE TYPE RG-178/U, 196 1.20 +.025 f (GHz) 0-12.4 GHz 142-0402-001 142-0402-006 RG-161/U, 174,188, 316 RG-188 DS, RG-316 DS RG-58/U, 141,
More informationTru products are now under the Tru-Win brand from Winchester Interconnect.
TRU MEIA Series Tru-Win MEIA offers the latest innovation in high power connector design. The MEIA interface provides equivalent kw power handling compared to similar EIA connector line sizes but provides
More informationC-L-X ARMOR REMOVAL PROCEDURES
C-L-X ARMOR REMOVAL PROCEDURES USING THE KETT MODEL #KS-226 CABLE SAW The procedure listed below details Okonite s recommended method for removing C-L-X armor from large and small diameter cables. These
More informationMicro-manipulated Cryogenic & Vacuum Probe Systems
Janis micro-manipulated probe stations are designed for non-destructive electrical testing using DC, RF, and fiber-optic probes. They are useful in a variety of fields including semiconductors, MEMS, superconductivity,
More informationSMB Connectors. Adaptors-50Ω. Plug to Plug. Jack to Jack. Plug to Jack. Bulkhead Jack to Jack
SMB Connectors Adaptors-50Ω Plug to Plug 1P-801-00 Jack to Jack 1P-802-00 Plug to Jack 1P-803-00 Bulkhead Jack to Jack 1P-804-18 Mini-SMB 75Ω Straight Plug 1P75-111-00 Cable group RG316 Straight PCB Jack
More informationBroadband performance with low reflection DC to 4 GHz provides low cost connector combined with high quality.
Amphenol RF 36 Connectors Description The name derives from SubMiniature B (the second subminiature design). Developed in the 1960 s, this sub miniature interface has snap-on coupling. Amphenol s connectors
More informationAmphenol RF. MMCX Micro-Mate (MMCX) Connectors MMCX. Description. Features/Benefits. Applications
Amphenol RF 14 Micro-Mate () Connectors Description (also called MicroMate TM ), is a micro-miniature connector series with a snap-lock mechanism allowing for 360 degrees rotation enabling flexibility
More informationCSP-03G-003 High-Frequency Coaxial Test & Measurement Probe Model Number: CSP-03G-003, Replacement Probe: SPL-03G-043, SPL-03B-121 Target Connector: CPT-03-50-2 Applications: Designed for use in interconnect
More informationMillikelvin measurement platform for SQUIDs and cryogenic sensors
Cryoconference 2010 Millikelvin measurement platform for SQUIDs and cryogenic sensors M. Schmidt, J. Beyer, D. Drung, J.-H. Storm Physikalisch-Technische Bundesanstalt, Abbe Str. 2-22, 10587 Berlin, Germany
More informationCu 0.37 Brass Cu 0.37 Brass
To: From: EDGES MEMO #148 MASSACHUSETTS INSTITUTE OF TECHNOLOGY HAYSTACK OBSERVATORY WESTFORD, MASSACHUSETTS 01886 October 7, 2014 Telephone: 781-981-5400 Fax: 781-981-0590 EDGES Group Alan E.E. Rogers
More informationConduit measured transfer impedance and shielding effectiveness (typically achieved in the RS103 and CS114 tests)
Conduit measured transfer impedance and shielding effectiveness (typically achieved in the RS3 and CS4 tests) D. A. Weston K. McDougall conduitse.doc 5-2-27 The data and information contained within this
More informationGlenair s Series 80 ASAP Cordsets for High-Speed Ethernet, USB and Firewire Applications
General Information Compact Weight-Saving Design with size #23 Contacts SB 2.0, 100BASE-T, 1000BASE-T, IEEE 1394 Environmentally Protected, Robust Construction Aerospace-Grade Cable Meets FAA FAR 25 Flammability
More informationMGA Magnetic field system. DC khz
MGA 1030 Magnetic field system DC - 250 khz EN 55103-1 + 2, EN 61000-4-8, Automotive, MIL-STD a.o. Generation and measurement of magnetic fields from DC up to 250 khz Field strengths up to 1000 A/m Additional
More informationSMA Description Applications Features
MCX SMA Description SMA connectors are adaptable to interconnection requirements of both systems and components.s - Corm offers a wide variety of cable connectors,receptacles, feed thrus, end launches,
More informationFST Series HUMIDITY-TEMPERATURE TRANSMITTERS INSTRUCTION MANUAL
FST Series HUMIDITY-TEMPERATURE TRANSMITTERS INSTRUCTION MANUAL 20020628 CONTENTS DESCRIPTION... 3 OPERATION... 4 Power Supply...4 Output Range...4 Temperature Operating Range and Temperature Limits...4
More informationCatalog of CLA force and torque sensors
Catalog of CLA force and torque sensors SC-002 LC-01 LC-10 TSF-000 TSF-05 TSF-1 TSF-100 Micro-force sensor Force sensor Micro-torque sensor Torque sensor Phone +41 32 421 44 90, Fax +41 32 421 44 91, ventes@cla.ch,
More informationSMA 50 Ohm Connectors Alphabetical Index INCHES (MILLIMETERS) CUSTOMER DRAWINGS AVAILABLE ON REQUEST
SMA 50 Ohm Connectors Alphabetical Index SMA Connectors - 50 Ohm Bulkhead Mount... 20 Custom Feedthroughs... 48 Dummy Loads... 37 End Launch... 16 Field Replaceable... 28 Flexible Cable... 8 In-Series
More informationREP Design LLC. 193 Winding Ridge Rd, Southington, CT INSTALLATION INSTRUCTIONS:
REP Design LLC 193 Winding Ridge Rd, Southington, CT 06489 1-860.426.1894 n7emw@cox.net www.repdesign.us INSTALLATION INSTRUCTIONS: SHD-SO239 Super Heavy Duty SO-239Antenna Mounting System Thank you for
More informationTest Cable Assemblies
Test Cable Assemblies DC-65 GHz 8851 SW Old Kansas Ave. Stuart, FL 34997 USA +1-772-286-9300 +1-800-544-5594 sales@emc-rflabs.com www.emc-rflabs.com Premium Test Cable Lab-Flex 200 Frequency to 31 GHz
More informationLoop & Magnetic Field Coil
Model 6502 10 khz 30 MHz Model 6507 1 khz 30 MHz Model 6509 1 khz 30 MHz Model 7603 20 Hz >50 khz Model 7604 20 Hz 500 khz Model 7605 30 Hz >50 MHz Saturation Indicator Remote Monitor Option Quality Construction
More informationFlexible AC current probes
Flexible AC current probes Making use of the principle of Rogowski coils, the MiniFLEX models are flexible sensors offering a wide dynamic range for measuring AC intensities and viewing high-speed current
More informationV4 Premium Kit. Prusa i3 Build Guide
V4 Premium Kit Prusa i3 Build Guide Hi! Congratulations on your purchase of the DIYElectronics.co.za Prusa I3 kit, the best South African 3D Printer Kit! Hopefully this should serve as complete guide to
More informationWisconsin Contractors Institute Continuing Education
IMPORTANT NOTE: You should have received an email from us with a link and password to take your final exam online. Please check your email for this link. Be sure to check your spam folder as well. If you
More informationFrom dc to 10 GHz the. VSWR shall not exceed 1.3 &.04 (f) where f is the frequency in Gigahertz (GHz).
121 Series Coaxial Snap On & Screw On Types / 50 Ohm & 75 Ohm These 50 and 75 Ohm coaxial connectors are easily inserted into your printed circuit board using an insertion tool. Solder is eliminated and
More information- Datasheet - Features: Version 1.1. Cryogenic Low Pass Filter Unit Type KA-Fil 2a
Cryogenic Low Pass Filter Unit Type KA-Fil 2a - Datasheet - Version 1.1 Features: 5 Independent Low Pass Filters Operating Range 300K to 4.2K Overriding Diodes allow Bypassing and Pulsing Small Size 2009
More informationSECTION 14. DIN 1.0/2.3 / DIN 1.6/5.6 / Type 43 R118 / R120 / R129 / R214
SECTION 14 14 DIN 1.0/2.3 / DIN 1.6/5.6 / Type 43 R118 / R120 / R129 / R214 Contents DIN 1.0/2.3 Introduction... 14-4 Interface... 14-4 Characteristics Eco... 14-5 Plugs Eco... 14-6 Jacks Eco... 14-6
More informationAMP-13 OPERATOR S MANUAL
AMP-13 OPERATOR S MANUAL Version 2.0 Copyright 2008 by Vatell Corporation Vatell Corporation P.O. Box 66 Christiansburg, VA 24068 Phone: (540) 961-3576 Fax: (540) 953-3010 WARNING: Read instructions carefully
More informationMASSACHUSETTS INSTITUTE OF TECHNOLOGY HAYSTACK OBSERVATORY
To: From: EDGES MEMO #073 MASSACHUSETTS INSTITUTE OF TECHNOLOGY HAYSTACK OBSERVATORY WESTFORD, MASSACHUSETTS 01886 Updated July 16, 2012 Telephone: 781-981-5407 Fax: 781-981-0590 EDGES Group Alan E.E.
More informationCorning Gilbert Inc. Microwave Push-on Interconnects 1
Corning Gilbert Inc. Microwave Push-on Interconnects 1 GPO Specifications General Characteristics Impedance 50 ohms nominal Frequency range DC to 40 GHz Temperature range -65 C thru 165 C Electrical Characteristics
More informationModel SR554 Transformer Preamplifier
Model SR554 Transformer Preamplifier Model SR554 Transformer Preamplifier 1290-D Reamwood Avenue Sunnyvale, California 94089 Phone: (408) 744-9040 Fax: (408) 744-9049 email: info@thinksrs.com www.thinksrs.com
More informationAmphenol RF MCX. MCX Connectors MCX. Description. Features/Benefits. Applications
Amphenol RF 20 Connectors Description connectors conform to the European CECC 22000 spec and were introduced in the 1980 s. While the uses identical inner contact and insulator dimensions as the SMB, the
More informationA-Size 7/8" powerfast Connectivity
A-Size 7/8" powerfast Connectivity A-Size 7/8" powerfast Cordset Part Number Key R K M 34 - *M /S.. A-Size 7/8" powerfast Cordset R = straight W = right angle Y = male connector, female threads (blank)
More informationValve Island with Electronic I/O
Screw in Temperature /Switch with display for ON/OFF Control Indication, monitoring, transmission and ON/OFF control in one device Extra large display Menu guided parametrisation Complete communication
More informationSetting Standards Connectors M 16
Setting Standards Connectors M 16 inclusive 15 Product Overview 16 Housings page 18 Inserts page 22 Accessories page 29 Technical Data M 16 Control Signal Connectors Mechanical Data Housing Materials and
More informationTECHNICAL REPORT: CVEL Parasitic Inductance Cancellation for Filtering to Chassis Ground Using Surface Mount Capacitors
TECHNICAL REPORT: CVEL-14-059 Parasitic Inductance Cancellation for Filtering to Chassis Ground Using Surface Mount Capacitors Andrew J. McDowell and Dr. Todd H. Hubing Clemson University April 30, 2014
More informationC240-NFSM-3M. Jumper Assembly Sample Label. Product Classification. General Specifications. Return Loss/VSWR
C240-NFSM-3M Product Classification Brand Product Series Product Type CNT Jumper with interface types N Female and SMA Male, 3m CNT Braided cable assembly General Specifications Body Style, Connector A
More information400 (±2,5 V/ V/ ,3% V4A
LVDT Inductive Position Transducer - Hydraulic Series Series Hydraulic position measurement in hydraulic cylinders of machine controls ranges 10...300 mm temperature -40...+150 C (sensors) 0...+60 C (external
More informationA NISE funded Basic Research Project. Technical Document 3277 September SSC Pacific San Diego, CA Benjamin J.
Technical Document 3277 September 2013 An Experimental Platform for Performing Measurements of the RF Magnetic Permeability and Electric Permittivity of Functional Materials at Cryogenic Temperatures A
More informationWiFi Interface Identifier
WiFi Interface Identifier WiFi Interface Identifier Today s wireless market has exposed us to many new, and some familiar connectors. The wide range of antennas, access points, routers, WLAN s, cellular
More informationRF Microwave Standard Assemblies
RF Microwave Standard Assemblies RF Microwave Standard Assemblies 146 Q-Flex Series Specifications Q-Flex assemblies are a unique ALTERNATIVE to custom designed flexible coaxial cables.traditionally custom
More informationTRUtest Specifications. Electrical. Mechanical. Environmental. Requirement. Detail. 1.35:1 maximum. 0.4 db/ft GHz
TRUtest Series TRUtest Series cable assemblies combine MIL-standard test-grade interfaces with flexible and durable cable construction to provide repeatable, reliable performance and long service life.
More informationLocator Accessories DATA SHEETS. Accessory Range for Pipe & Cable Location Equipment
Locator Accessories DATA SHEETS Accessory Range for Pipe & Cable Location Equipment GENERAL PURPOSE SONDE The C.SCOPE 8kHz and 33kHz General Purpose Sondes are transmitters used to trace the direction
More informationThe Discussion of this exercise covers the following points:
Exercise 5 Resistance and Ohm s Law EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the notion of resistance, and know how to measure this parameter using an ohmmeter.
More informationLoad Cell Accessories and Services
Load Cell Accessories and Services Highlights Strain gage signal conditioners Cable assemblies Mounting accessories Calibration services PCB Piezotronics, Inc. Toll-Free in USA 888-684-0004 716-684-0001
More informationResistance Thermometers Model Series TR7X0, Sheathed Design
Electrical Temperature Measurement Resistance Thermometers Model Series TR7X0, Sheathed Design WIKA Data Sheet TE 60.40 Applications T Suitable for all industrial and laboratory applications Special Features
More informationINDEX Unflanged Elbows 7/8 Male - Male...2 1+5/8 Male - Male...3 1+5/8 Male - Female...4 1+5/8 Female - Female...5 3+1/8 Male - Male...6 Flanged Elbows 7/8...8 1+5/8...9 3+1/8...10 Coaxial Adaptors 7/8
More informationEthernet & High Speed Networks. Quadrax Contact up to Cat6 MIL-DTL-38999/ARINC 600/EN2997/EN3646
Ethernet & High Speed Networks Quadrax Contact up to Cat6 MIL-DTL-38999/ARINC 600/EN2997/EN3646 Quadrax Contact Presentation Today s technology for Aeronautic and Military equipment is more and more complex,
More informationHF860 Radio Frequency Probe
Connector type Specific HF860 order code Connecting element SMA-Female HF86002B0001G530 SMB- HF86005B0004G530 SMB-Female HF86002B0005G530 SMC- HF86005B0003G530 U.FL- HF86005B0002G530 RF- HF86005B0007G530
More informationCurrent Probes. User Manual
Current Probes User Manual ETS-Lindgren Inc. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reason. Nothing contained herein shall
More informationMaterials (other materials see WIKA diaphragm seal program) Model S-10
2.0 Specifications WIKA Tronic catalog pages and data sheets have a consistent layout of technical information that is required to select the correct transmitter. The second page of the data sheet lists
More informationtotal j = BA, [1] = j [2] total
Name: S.N.: Experiment 2 INDUCTANCE AND LR CIRCUITS SECTION: PARTNER: DATE: Objectives Estimate the inductance of the solenoid used for this experiment from the formula for a very long, thin, tightly wound
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationSW 16mm. SW 15mm. SW 19mm
M B-Coding Automation Technology 7 series Screw locking acc. to DIN EN 6076--0 Degree of protection IP67 Moulded versions Degree of protection IP68 Easy assembly Excellent EMC shielding Versions with shielding
More informationRF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].
RP SMA Male Connector Solder Attachment for PE-SR402AL, PE-SR402FL, PE-SR402FLJ, PE- SR402TN, RG402, Gold Plated Brass Body RF Connectors Technical Data Sheet PE44724 Configuration SMA Male Reverse Polarity
More informationK3D60a ±100N. Description. The K3D60a three-axis sensor is suitable for measuring force on three mutually perpendicular axes.
K3D60a ±100N Description The K3D60a three-axis sensor is suitable for measuring force on three mutually perpendicular axes. The new 3-axis sensor K3D60a is a further development of the series K3D60 and
More informationSeries 791 Connectors
Pin and Socket s for Series 79 Connectors Crimp s Size 23 Crimp s Operating temperature: -65 to +150 C Current rating: 5A Crimp Tensile Strength Wire Size Axial Load (lbs.) 22 12 24 8 26 5 28 3 30 1.5
More informationMale Cable Connectors / Female Receptacles Male cable connector straight, with internal strain relief clamp and/or clamping ring, cable diameter 6-12,5 mm No. of contacts 3 + PE 3 + PE Termination technique
More informationEVOLUTION OF THE CRYOGENIC EDDY CURRENT MICROPROBE
EVOLUTION OF THE CRYOGENIC EDDY CURRENT MICROPROBE J.L. Fisher, S.N. Rowland, J.S. Stolte, and Keith S. Pickens Southwest Research Institute 6220 Culebra Road San Antonio, TX 78228-0510 INTRODUCTION In
More informationDC Circuits, Ohm's Law and Multimeters Physics 246
DC Circuits, Ohm's Law and Multimeters Physics 246 Theory: In this lab we will learn the use of multimeters, verify Ohm s law, and study series and parallel combinations of resistors and capacitors. For
More informationEMC Near-field Probes + Wideband Amplifier
1 Introduction The H20, H10, H5 and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC precompliance measurements. The probes are used in the near field of sources of electromagnetic
More informationInstruction Manual T-800 Series Current Transmitter. Model T-800L Model T-800LT Model T-800TT
Instruction Manual T-800 Series Current Transmitter Model T-800L Model T-800LT Model T-800TT M323 Rev G1 September 10, 2009 JOWA USA, Inc. 59 Porter Road Littleton, MA 01460-1431 USA Telephone: 978-486
More informationRP SMA Male Right Angle Connector Solder Attachment for PE-SR402AL, PE-SR402FL, RG402
RP SMA Male Right Angle Connector Solder Attachment for PE-SR402AL, PE-SR402FL, RG402 RF Connectors Technical Data Sheet PE4790 Configuration SMA Male Reverse Polarity Connector MIL-STD-348 50 Ohms Right
More informationNEW. Automation Technology 768 series
Automation Technology 78 series Screw locking acc. to DIN EN 07--0 Degree of protection IP7 Moulded versions Easy Assembly Excellent EMC shielding (versions with shielding rings 0 ) Versions with shielding
More informationGenerator Power [kw]
PW3-25-SA/80 PW3-50-SA/80 PW3-100-SA/80 0 25 50 75 100 Generator Power [kw] 100-SA/80 Generator Overall Dimensions 25-SA/80 and 50-SA/80 Generator PWH-22 PWH-20 PWH-24 Capacity Output Power Dimensions
More informationAC/DC Resistance Standard DRR-112
AC/DC Resistance Standard DRR-112 Operator's Manual DTM Instruments, LLC www.dtminstruments.com Version 2.0 November 2013 Introduction The AC/DC resistance standard DRR-112 is used to calibrate resistance
More informationn Measurable displacements between n Linearity: max. ± 0.05 % n Housing diameter 12.9 mm n Service life: 10 8 movements
Potentiometric Displacement Sensor Miniature design Model 8709 Code: Delivery: Warranty: 8709 EN ex stock 24 months Application Potentiometric displacement sensors are used for direct, precise measurement
More informationCurrent clamps for AC current
Current clamps for AC current Y series The Y series clamps are designed to be both rugged and versatile whilst remaining easy to use. The jaws are designed so that the clamps can be hooked onto cables
More informationRosemount 5408 and 5408:SIS Level Transmitters
Quick Start Guide 00825-0100-4408, Rev AD March 2018 Rosemount 5408 and 5408:SIS Level Transmitters Cone Antenna Quick Start Guide March 2018 1 About this guide This Quick Start Guide provides basic guidelines
More informationReversePolarity Series(SMA,BNC,TNC)
RP ReversePolarity Series(SMA,BNC,TNC) Description Reverse polarity BNC, TNC, N & SMA connectors (RP-BNC, RP-TNC, RP-SMA) are designed for uses in wireless applications where a non-standard interface has
More informationLC31L-BAT Link Coupler
Instruction Manual For the LC31L-BAT Link Coupler 09 March 2018 2012-2018 by Ralph Hartwell Spectrotek Services All rights reserved 2 RADIO FREQUENCY WARNING NOTICE If the LC31L-BAT is installed incorrectly
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/30 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, RECEPTACLE, SOCKET CONTACTS, SHELL SIZE 1, SIZE 20 SIGNAL
More information