850 MHz Antenna Sharing Combiner ASC850VG12A
|
|
|
- Joshua Carpenter
- 6 years ago
- Views:
Transcription
1 DATA SHEET Small, lightweight, outdoor unit Dual Technology Combiner (GSM 850 / UMTS 850) Can also be used for same technology (e.g. GSM/GSM) Can be used close to Antenna Can be used in Ground Based Applications while maintaining Diversity Path Can operate as a Passive Combiner in non-dc fed system Rx path is Independent of Tx path Can survive incorrect installation as ports are protected AISG 2.0 compatible unit ASC receives DC Voltage and AISG sampling at the UMTS BTS-1 port ASC operates at constant power High Linearity Lightning protected Fail-safe bypass mode High reliability Overview CCI s Dual Technology Antenna Sharing Combiner (ASC) allows two Base Stations to share the same antennas and preserves Receive Diversity without any combining losses. In the Downlink direction, the transmit signal from each Base Station is directed to one of the two antenna ports. In the uplink direction, an Amplifier compensates for combining losses normally associated with passive combiners. The Gain of the amplifier can be controlled remotely using AISG 2.0 Protocol, and the gain level to each BTS can be independently controlled. Technical Description: The ASC system consists of a twin outdoor tower mount unit with two antenna inputs. The tower mount unit is dual duplexed to separate the low-power uplink signal from the high-power downlink signal at the antenna port, amplifies the low-level uplink signals using an ultra-low noise amplifier (LNA), and recombines the two paths at the BTS port. In addition, the uplink signal is split out after the LNA and routed to the BTS diversity port. The tower mount units consist of six band-pass filters, four redundant low-noise amplifiers, two splitters, bypass failure circuitry, and bias tee s which are all housed in an IP65 moisture proof enclosure, with IP68 Immersion proof connectors suited to long-life masthead mounting. The unit provides protection against lightning strikes via a multi-stage surge protection circuit. AISG 2.0 DC power and control is provided via the feeder cable from the BTS using the AISG 2.0 and 3GPP standard. The ASC is powered through the UMTS (BTS-1) port. Additionally the ASC operates at constant power when powered by an AISG 2.0 Compatible Site Control Unit, or BTS. A separate AISG connector is also provided to allow direct AISG connection or Daisy Chaining to multiple AISG products at the top of the tower. With fully protected input ports, the unit can be installed without the concern of damaging the unit should it be incorrectly installed CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
2 DATA SHEET Applications Functions as a combiner for same band Base Station Equipment, (Can be same technology (e.g. GSM and GSM) or different technology (e.g. GSM and UMTS)) enabling Rx Diversity and overcoming losses normally associated with passive combiners. Can be used close to the antenna, enabling Remote Radio Head equipment to be combined with Coaxial fed systems which use a pair of Coaxial Feeder Lines. Gives additional gain for overcoming feeder and combining losses. Can be used in ground based applications, as a combiner. Overcomes losses and maintains Rx Diversity path. PDU has flexibility to be used in non-dc fed systems, thus giving passive combining of two same band systems into coaxial feeder line pair CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
3 SPECIFICATIONS Electrical Specification RF Parameters Ports Frequency(MHz) Specification Return Loss ANT db min. (16 db bypass mode) db min. BTS db min. (16 db bypass mode) db min. Gain ANT - BTS to 12 db adjustable in 0.25 db steps via AISG (± 0.5 db) Insertion Loss ANT - BTS (RX Bypass mode) db max. ±0.3 db passband ripple ANT - BTS (TX) db typ. ±0.1 db passband ripple Noise Figure ANT - BTS db 25 max gain, 1.8 db 65 max gain Input Third Order Intercept Point ANT - BTS db min. at max. gain General Characteristics Impedance 50 ohms Continuous Average Power 200 W max. Peak Envelope Power 2 kw max. Intermodulation Performance(all ports) <-110 dbm (-153 dbc) typical (2 +43 dbm tones) all bands Operating Voltage +10V to +30V DC provided via coax or AISG Power Consumption 4.0 W Environmental Specification Operating Temperature Enclosure MTBF Lightning Protection -40 C to +60 C IP65 (Unit Body), IP68 (Connector >500,000 hours 8/20us, ±2KA max, 10 strikes each, IEC Mechanical Specification Dimensions (w/o connectors or brackets)(h W D) Connectors DIN 7-16 female x 6 (BTS (x 2), ANT (x 2), RxD (x 2)), AISG x x 7.87 x 4.02 in. (270 x 200 x 102 mm) Dimensions (with brackets)(h W D) Weight (w/o Bracket) Weight (with Bracket) Mounting x in. (363 x 211 x mm) 15.4 lbs (7.0 kg) approx lbs (7.5 kg) approx Pole/Wall Mounting Bracket 2015 CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
4 SPECIFICATIONS ASC850VG12A Outline Drawing 2015 CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
5 SPECIFICATIONS Block Diagram ASC850VG12A Block Diagram 2015 CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
6 ORDERING Parts & Accessories ASC850VG12A 850 MHz Dual Technology Outdoor Antenna Sharing Combiner 2015 CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
7 STANDARDS & CERTIFICATIONS Certifications Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US 2015 CCI All rights reserved. Specifications are subject to change. DS-ASC850VG12A-V
900 MHz Antenna Sharing Combiner ASC900VG11A
DATA SHEET Small, lightweight, outdoor unit Dual Technology Combiner (GSM 900 / UMTS 900) Can also be used for same technology (e.g. GSM/GSM) Can be used close to Antenna Can be used in Ground Based Applications
AWS Antenna Sharing Combiner
DATA SHEET Small, lightweight, outdoor unit Multi-Technology Combiner (GSM/UMTS/CDMA/LTE AWS Band) Can also be used for same technology (e.g. UMTS/UMTS or LTE/LTE) Can be used close to Antenna Can be used
Spectrum Sharing 900 MHz Combiner
DATA SHEET Combines two 900 MHz base station outputs with a narrow guard band onto a common port Full transmit and receive band combining with a guard band of 0.8 to 3 MHz High power 400 W per input port
DAS Interface Module DAST-700-MODA-30 DATA SHEET. Overview
DATA SHEET A common connection point for Upper and Lower Band LTE Base stations to a single DAS system Levels and equalizes performance for all base stations with Integrated Level Controls No need to attenuate
Low Loss Combiner LLC-1900-IN DATA SHEET. Overview
DATA SHEET Combines Multiple Technologies onto a Single Feed Line Low Loss Combining Combining for Multiple Technologies (GSM/UMTS, UMTS/UMTS, UMTS/LTE, CDMA/LTE, etc.) Minimal or No Guard Band High Reliability
ATSBT-BOTTOM-FM-4G. Electrical Specifications. Product Classification. General Specifications. Mechanical Specifications. Bottom Smart Bias Tee
Electrical Specifications EU Certification Bottom Smart Bias Tee Injects AISG power and control signals onto a coaxial cable line Reduces cable and site lease costs by eliminating the need for AISG home
Cellular (850 Band) DAS. Tray with Independent Control. General Information. Key Features: Tel: Fax:
Cellular (850 Band) DAS Interface Tray with Independent Control Tel: 201-342-3338 www.cciproducts.com General Information CCI s Cellular Band DAS Interface Tray with Independent Control provides an integrated,
INSTALLATION and OPERATION INSTRUCTIONS. FOR FiberLink BI-DIRECTIONAL AMPLIFIER WITH DIVERSITY MW-FBDA-800AB-50W-DIV
INSTALLATION and OPERATION INSTRUCTIONS FOR FiberLink BI-DIRECTIONAL AMPLIFIER WITH DIVERSITY MW-FBDA-800AB-50W-DIV Page 1 of 15 TABLE OF CONTENTS PARA No. PARAGRAPH PAGE No. 1. OVERVIEW 3 2. COMPONENT
Small Cell 65 Degree Panel Antenna
DATA SHEET Small Cell Sector antenna optimized over the PCS (1850-1995 MHz) and BRS (2496 to 2690 MHz) bands Cross-Pol design for 2x2 MIMO Excellent upper sidelobe suppression Designed for superior Front
4-Port Antenna MHz mm
Twin band antenna, dual polarisation, 4 connectors Independent tilt on each band 0-12 / 0-12 MET and RET versions, 3GPP/AISG2.0 Single RET module to control all tilt angles, fully inserted inside the antenna
Major Products. RF/Microwave provider
Major Products Products 1 RF Sub-systems Combiner FEU TTA TMA SCU 2 Products 2 RF components Power Splitter (BTS) Filter Switch Coupler 3 Feature1 Divider Frequency Range 824~894, 1750~1870, 1885~2170,
DTMA-1800-UMTS-12-AISG
DTMA--UMTS-12- Double units for easy use with XXPol antennas Suitable for antenna RET control according to /3GPP standard Bypass mode to ensure cell operation in case of power down Supports 1.1 and 2.0
TriBand Twelve-Port Antenna
DATA SHEET Six foot (1.8 m) TriBand, twelve port antenna with a 65 azimuth beamwidth covering 694-960 MHz and 1695-2690 MHz frequencies Eight wide high band ports covering 1695-2690 MHz and four wide low
TriBand Antenna HPA65R-KE4A DATA SHEET
DATA SHEET Four foot (1.2 m), TriBand, six port antenna with a 65 azimuth beamwidth covering 694-960 MHz and 1695-2690 MHz frequencies Four wide high band ports covering 1695-2690 MHz and two wide low
Multi-Band Twelve-Port Antenna
DATA SHEET Eight foot (2.4 m) multiband, twelve port antenna with a 65 azimuth beamwidth covering 698-896 MHz and 1695-2400 MHz frequencies Eight high band ports covering 1695-2400 MHz and four low band
Special Events Multibeam Antenna
DATA SHEET Six dual beams optimised for maximum throughput over the PCS band Three foot (0.9 m), single-panel design supports six beams - without mount changes Each beam pair dual +45 /-45 polarized Seperate
Twelve Port Multi-Band Antenna
DATA SHEET Four foot (1.2 m) multiband, twelve port antenna with a 65 azimuth beamwidth covering 698-798 MHz, 824-896 MHz and 1695-2360 MHz frequencies Total of Eight high band ports, four high wide band
Twelve Port Multi-Band Antenna
DATA SHEET Eight High Broadband ports covering PCS, AWS / AWS-3 and WCS bands (698-798 MHz, 824-896 MHz. & 1695-2360 MHz.) Four Low Band ports covering 700 MHz and 850 MHz bands Supports 8x8 MIMO in high
Ultra Wideband Six Beam Antenna
DATA SHEET Ultra wideband coverage 1695-2690 MHz, including AWS & AWS-3, DCS 1800, PCS, UMTS 2100, WCS and BRS/2.6 GHz bands 3 ft (0.7 m) tall, single panel design supporting six beams without mount changes
OctoPort Multi-Band Antenna
DATA SHEET Four foot (1. m) multiband, eight port antenna with a 65 azimuth beamwidth covering 698-798, 84-896 MHz and 1695-400 MHz frequencies Four wide high band ports covering 1695-400 MHz and four
HexPort Multi-Band Antenna
DATA SHEET Six foot (1.8 m), six port antenna with a 65 azimuth beamwidth covering 698-894 MHz and 1710-2360 MHz frequencies Four high band and two low band ports including the WCS band in a single antenna
HexPort Multi-Band Antenna
DATA SHEET Six foot (1.8 m), six port antenna with a 33 azimuth beamwidth covering 698-894 MHz and 1710-2360 MHz Four high band and two low band ports including the WCS band in a single antenna Sharp elevation
Twelve Port Multi-Band Antenna
DATA SHEET Twelve Port Multi-Band Antenna Eight foot (2.5 m) multiband, twelve port antenna with a 45 azimuth beamwidth covering 698-960 MHz and 1695-2360 MHz frequencies Eight wide high band ports covering
Ten/Five Beam Special Events Antenna
DATA SHEET Five low band beams optimized for maximum throughput over frequency bands (698-896 MHz); Ten high band beams optimized for maximum throughput over frequency bands (1695-2180 MHz) Three foot
Hybrid Bi-SectorTM Array
DATA SHEET Eight foot (2.4 m), multiband, ten port Hybrid Bi-Sector Antenna. Deploying a high performing 65 azimuth beamwidth covering 698-960 MHz and a pair of CCI s Patented Asymmetrical 33 Shaped Beams
Product Classification. Mechanical Specifications. Dimensions. Regulatory Compliance/Certifications. Included Products
ATBTK-FM Bias Tee Kit, AISG Compatible 698-2170 MHz Product Classification Product Type RET bias tee Mechanical Specifications Antenna Interface BTS Interface 7-16 DIN Male 7-16 DIN Female Dimensions Depth
4-Port Antenna MHz mm
Dual band antenna, dual polarisation, 4 connectors Independent tilt on each band 0-14 / 0-12 UltraLine platform with multi-array capability MET and RET versions, 3GPP/AISG2.0, in multiple single RET (multiple
Ten Port Multi-Band Antenna
DATA SHEET Eight High Broadband ports simultaneously covering PCS, AWS / AWS-3 and WCS bands Eight High Broadband ports with two Low Band ports in one antenna Excellent elevation side-lobe performance
Multi-band Bi-Sector TM Array
DATA SHEET Multi-band Bi-Sector TM Array Six foot (1.8m), twelve port, dual beam antenna with patented asymmetrical beam shapes optimized for LTE Two independent 33 beams to match existing 65 patterns,
Ten Port Multi-Band Antenna
DATA SHEET Six foot (1.8 m) multiband, 10 port antenna with a 65 azimuth beamwidth covering 698-896 MHz and 1695-360 MHz frequencies Full Spectrum Compliance for WCS, AWS3 and upcoming Band 14 Operations
Ultra-wideband Bi-SectorTM Array
DATA SHEET Five foot (1.4 m), four port, dual beam antenna with patented asymmetrical beam shapes optimized for LTE Two ultra-wideband 33 beams to match existing 65 patterns, covering 1710-2400 MHz One
Introduction to Same Band Combining of UMTS & GSM
Introduction to Same Band Combining of UMTS & GSM Table of Contents 1. Introduction 2 2. Non-Filter Based Combining Options 2 3. Type 1 Combiners 2 4. Type 2 Combiners 3 5. Overview of Active & Passive
Hybrid Bi-SectorTM Array
DATA SHEET Eight foot (2.4m), multiband, ten port Hybrid Bi-Sector Antenna. Deploying a high performing 65 azimuth beamwidth covering 698-960 MHz and a pair of CCI s Patented Asymmetrical 33 Shaped Beams
Hybrid Bi-SectorTM Array
DATA SHEET Six foot (1.9 m), multiband, Ten port Hybrid Bi-Sector Antenna. Deploying a high performing 65 azimuth beamwidth covering 698-960 MHz and a pair of CCI s Patented Asymmetrical 33 Shaped Beams
Superseded. Small Cell IDA Antenna IDA-30F-KE-H2 DATA SHEET. Overview. Applications
DATA SHEET Overview Applications 2 ports covering bands between 698 and 960 MHz and 2 ports covering bands between 1695 and 2690 MHz Constant 30 vertical by 30 horizontal beamwidth MIMO and SISO capable
Wideband Quasi-Omni Antenna
DATA SHEET Two foot (0.5 m), two port, quasi-omni antenna with uniform horizontal beamwidths covering the extended band from 1710-2690 MHz 360 of coverage area across all bands of operation in a single
RB-NKC1 3dB Hybrid Coupler - CDMA800/GSM900, MHz
Hybrid Couplers RB-NKC1 3dB Hybrid Coupler - CDMA800/GSM900, 800-960MHz High input power of 200W. Permits combining of CDMA800 and GSM900 services. Low insertion loss of 0.15dB. High inter-band isolation
12-Port Antenna MHz mm
G Dx + Next Generation Twin tri band antenna, dual polarisation, 12 connectors Independent tilt on each band 2-12 / 2-12 / 2-12 / 2-12 / 2-12 / 2-12 Lightweight Twin+, next generation TwinLine platform
Frequency Range (MHz) CONNECTOR TYPE Female. Manual Electrical Tilt (MET) --- Three Sectors
Tri band, tri-sector antenna, 18 connectors Independent tilt on each band 2-10 / 0-10 / 0-10 Independent azimuth panning ±15 on each sector MET and RET versions, 3GPP/AISG2.0 Our patented, RET module controlling
Wideband Quasi-Omni Antenna
DATA SHEET Two foot (0.5 m), two port, quasi-omni antenna with uniform horizontal beamwidths covering the extended band from 1710-2690 MHz 360 of coverage area across all bands of operation in a single
DTMA AISG. Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier)
Compact line Double units for easy use with XPol antennas Supports AISG 1.1 and AISG 2.0 (default) Suitable for antenna RET control according to AISG/3GPP standard By-pass mode to ensure cell operation
14-Port Antenna MHz mm
+ Next Generation Hepta band antenna, dual polarisation, 14 connectors Independent tilt on each band 2-10 / 2-10 / 2-12 / 2-12 / 2-12 / 2-12 / 2-12 Lightweight Twin+, next generation TwinLine platform
Multi-Band Quasi-Omni Antenna
DATA SHEET Two foot (0.6 m), multi-band, four port quasi-omni antenna with 360 of coverage, covering 698-896 MHz and 1710-2360 MHz frequencies Two wide high band ports covering 1710-2360 MHz and two wide
Low Wideband Quasi-Omni Antenna
DATA SHEET Two foot (0.7 m), singleband, two port quasi-omni antenna with 360 of coverage, covering 694-960 MHz frequencies Two wide low band ports covering 694-960 MHz in a low weight and low profile
Wideband Six Beam Antenna
DATA SHEET Three foot (0.7 m) tall, single band, twelve port mutlibeam array. Containing Six Independent Asymmetrical Shaped Beams covering 1695-2180 MHz frequencies Twelve wide high band Dual-Pol +45
ClearGain Tower Mounted Amplifier System 800/1900 MHz User Manual
ADCP-75-123 Issue 5 July 2004 ClearGain Tower Mounted Amplifier System 800/1900 MHz User Manual 1294153 Rev A Preface COPYRIGHT All Rights Reserved Printed in the U.S.A. REVISION HISTORY Issue 1 04/2000
INSTALLATION AND OPERATING MANUAL
INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM
8-Port Antenna MHz mm
Quad band antenna, dual polarisation, 8 connectors Independent tilt on each band 2-12 / 2-12 / 2-12 / 2-12 Lightweight Twin+, next generation TwinLine platform and low windload MET and RET versions, 3GPP/AISG2.0,
DLNA-1800 Tower Mounted Amplifier Features
DLNA-18 Tower Mounted Amplifier Features Increased uplink signal sensitivity Increased range of operation Decreased number of dropped calls Bypass mode of operation in the case of a failure Visual display
White Paper. Network Coverage at its Best Tower Mounted Amplifiers
White Paper Network Coverage at its Best Tower Mounted Amplifiers Overview As cellular mobile networks continue to expand, operators keep trying to find cost-effective ways to improve network performance.
10-Port Antenna MHz mm
G Dx 5-Band, 10-Port,, XPOL, Panel Antenna, Variable Tilt, + Next Generation Penta band antenna, dual polarisation, 10 connectors Independent tilt on each band 2-12 / 2-12 / 2-12 / 2-12 / 2-12 Lightweight
ANTENNAFIER TM 915LTX BLOCK DIAGRAM LNA
Digitally Tunable 0.5 to 10 Watts This 915 LTX is a Outdoor High Power Digitally Tunable Bi-Directional Amplifier for 802.11b/g WLAN. It s tuned and powered over a 50 Ohm coax. Now you can fine tune your
The coupling torque at 7-16 connectors is Nm! The tightning torque for fi xing the AISG connector must be Nm!
Attention: The coupling torque at 7-16 connectors is 25-30 Nm! The tightning torque for fi xing the AISG connector must be 0.5-1 Nm! 936.2179a Änderungen vorbehalten Internet: http://www.kathrein.de Page
Omnidirectional Antenna Vertical Polarization Indoor and outdoor use
db Omnidirectional Antenna and outdoor use 17 27 Omni 17 27 6 2dBi 8 41 N female Connector position Bottom or top 17 27 MHz SWR < 1.8 2 dbi Intermodulation IM < 15 dbc (2 x 4 dbm carrier) ertical 5 W (at
12-Port Antenna MHz mm
G Dx 6-Band, 12-Port,, XPOL, Panel Antenna, Variable Tilt, + Next Generation Hex band antenna, dual polarisation, 12 connectors Independent tilt on each band 2-12 / 2-12 / 2-12 / 2-12 / 2-12 / 2-12 Lightweight
/ MHz
17-217 / 17-217 MHz WWX63X13x 2x X-Pol Twin Band VET Panel 6 16.8 / 16.8 dbi Ordering Options Manual Electrical Tilt Remote Electrical Tilt AISG v1.1 Remote Electrical Tilt AISG v2. / 3GPP Electrical Characteristics
4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by
4-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT set by R1 698 960 X 65 2 12 R2 698 960 X 65 2 12 4-Port Antenna 698 960/698 960 65 /65 15.5/15.5dBi 2 12 /2 12 T Type No. 80010901
12-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by
12-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT set by R1 R2 Y1 Y2 Y3 Y4 698 803 824 894 1695 2690 1695 2690 1695 2690 1695 2690 X X X X X X 65 65 65 65 65 65 1.5 10 1.5 10 2.5
12-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by
12-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT set by R1 R2 Y1 Y2 Y3 Y4 698 803 824 894 1695 2690 1695 2690 1695 2690 1695 2690 X X X X X X 65 65 65 65 65 65 2 12 2 12 2 14 2
65 Wideband Tri-Sector Antenna
DATA SHEET Two foot (0.5 m), six port, tri-sector antenna each sector with uniform horizontal beamwidths covering the extended band from 1710-2690 MHz Three individual 65 sectors arranged in a cloverleaf
PANEL ANTENNAS WITH ONLY HIGH BAND ARRAYS
PANEL ANTENNAS WITH ONLY HIGH BAND ARRAYS 54 April 2015 Ultra-wideband antennas designed to handle 2G, 3G networks and MIMO configurations for LTE on 1.8 / 2.1 / 2.6 networks. HighBand April 2015 55 (2x)
/ / MHz
7-9 / 17-217 / 17-26 MHz 6878 Tri Band Panel Antenna XXX-Pol 6 16. / 18.6 / 18.6 dbi Variable Tilt Tri band, XXX-Pol, variable tilt, panel antenna, 6 connectors Independent tilt on each band - / - / -
8-Port Antenna MHz mm
N G NG Quad band antenna, dual polarisation, 8 connectors Independent tilt on each band 0-10 / 0-12 / 0-12 / 0-10 UltraLine platform with multi-array capability MET and RET versions, 3GPP/AISG2.0 Single
Frequency Range (MHz) Connector Polarization XPOL XPOL XPOL XPOL XPOL
N G NG StreamLine Penta band antenna, dual polarisation, 10 connectors Independent tilt on each band 2-12 / 2-12 / 2-12 / 2-12 / 2-12 MET and RET versions, 3GPP/AISG2.0, in multiple single RET (multiple
GSM-R Terminal filter Technical Specification
Handling 3.2 GSM-R Terminal filter Technical Specification TRV 2014/71742 1 1 (17) Table of content 1 INTRODUCTION... 3 1.1 Scope... 3 1.1.1 The two problems... 3 1.1.1.1 Unwanted emission from public
ATBTK-MF-4G. Product Classification. Mechanical Specifications. Dimensions. Regulatory Compliance/Certifications.
ATBTK-MF-4G Bias Tee Kit, AISG Compatible 698-2700 MHz Product Classification Product Type RET bias tee Mechanical Specifications Antenna Interface 7-16 DIN Female BTS Interface 7-16 DIN Male Dimensions
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by R1 Y1 Y2 698 960 1710 2690 1710 2690 X X X 65 65 65 1 10 2.5 12 2.5 12 6-Port Antenna 698 960/1710 2690/1710 2690 65 /65
Standard C-band 10W BUC MODEL No. NJT5762 series
< Features > * High Efficiency & Low Distortion P1dB: +40 dbm min. over temperature IM3: -28 dbc @ Pout = +37 dbm Power Consumption: 69 W * Compact Size & Light Weight Weight: 3.2kg * AC Power Option *
REDUTELCO TECHNOLOGY CO.,LTD.
User Manual Wide Tri Band Booster (23dBm) REDUTELCO TECHNOLOGY CO.,LTD. 2013 January Information in this manual is subject to change without notice http:www.redutelco.com 2009 Redutelco All rights reserved
/ / / MHz
7-9 / 7-9 / 1710-2170 / 1710-2170 MHz Twin dual band, (2x) XX-Pol, variable tilt, panel antenna with 8 connectors Independent tilt on each band 0-10 / 0-10 / 0-10 / 0-10 Available as a Manual or Remote
4-Port Antenna ircu / /65 16/18.5dBi 0 10 /0 10 T V01
4-Port Antenna Frequency Range Dual Polarization Half-power Beam Width Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt 0 10 0 10 4-Port Antenna 698 894/1710 2170 65 /65 16/18.5dBi
Product Line. Represented by:
Product Line Represented by: Type of equipment How to read our BDA (or One Way) part number RBDA- 19 Rack BDA FOBDA Fiber Optic BDA RFOBDA Fiber in 19 rack BDA GXXX One Way Booster Band Type (See Frequency
Becker Nachrichtentechnik GmbH Kapellenweg Asbach - Germany
High Dynamic 8 Way Combiner 100 khz... 4000 MHz, 50 Ω Features - wideband - high dynamic - without signal losses - low power consumption - high port- to- port isolation - compact 19, 1 U design Applications
Universal/Standard Ku-band 8W BUC MODEL No. NJT8318 series
< Features > * High Temperature Operating Operation Guarantee Temperature Range: * Monitor & Control Line-up FSK Communication RS-232C Interface Serial < Line-Up > -40 to +75 C * RF Frequency Line-up Universal
Additional heat sink required!
8-850 MHz SUPER LOW NOISE AMPLIFIER WLA08-45A 1 WLA08-45A LNA is a super low noise figure, medium power, and high linearity amplifier with unconditional stable. The amplifier offers the exceptional noise
Universal/Standard Ku-band 8W BUC MODEL No. NJT8318 series
< Features > * High Temperature Operating Operation Guarantee Temperature Range: * RF Frequency Line-up Universal Ku-band: 13.75 to 14.5 GHz Standard Ku-band: 14.0 to 14.5 GHz * Monitor & Control Line-up
For detailed specifications or for your custom application, please contact your K&L sales representative. 20 db High Power Attenuator
DAS Overview As the LTE rollout continues and cellular frequency bands grow more congested, continuity of coverage becomes more challenging. Distributed Antenna Systems (DAS) provide one way to increase
Guide. Installation. Wilson Electronics, Inc. In-Building Wireless Amplifi er. Contents:
Amplifier Installation Guide In-Building Wireless Amplifi er Contents: Guarantee and Warranty 1 Antenna Options and Accessories 2 Before Getting Started / How It Works 2 Installation Overview 3 Installation
FEU (Front End Unit) for Optic Repeater
FEU (Front End Unit) for Optic Repeater 1. Specification 1.1. All Items Parameter Specification Comments RX1 RX2 TX Frequency Range. 1750.625 ~ 1769.375MHz 1750.625 ~ 1769.375MHz 1840.625 ~ 1859.375MHz
S14WI Splitter for Wireless Infrastructure
1 of 9 S14WI Splitter for Wireless Infrastructure Technical Product Data Features Active or Passive Options Available Optional Antenna Current Monitor and Alarm Optional Antenna DC Bias Select Pole-mount
Universal/Standard Ku-band GaN 40W BUC MODEL No. NJT8371 series
< Features > * GaN Technology Amplifier Inside * RF Frequency Line-up Universal Ku-band: 13.75 to 14.5 GHz Standard Ku-band: 14.0 to 14.5 GHz * High Efficiency Output Power Saturation Output Power: +46.0
Ku-Band VSAT Block Up Converters
FEATURES Single box BUC output power levels to 10W RS485 M&C capability Accurate RF Power Monitoring Maintenance Free Operation +24VDC or +48 VDC input voltage OPTIONS 10W L-Band to Ku-Band Block Up Converter
GSM DCS WCDMA Triple Band Repeater
CRF-GDW27-F GSM DCS WCDMA Triple Band Repeater Gain 80dB, Output 27dBm Overview: CRF-GDW27-F wireless Pico Repeater is a fast and cost effective solution widely deployed to provide coverage improvement
Dual Band Optical Repeater System
1 Optical DAS Coverage Solutions Dual Band Optical Repeater System BTS Link-204/208 with DBROU http://www.shyamtelecom.com www.shyamtelecom.com Optical DAS Coverage Solutions 2 BTS Link-204/208 with DBROU
BTS Link-104/108 with SBROU
1 Optical DAS Coverage Solutions Single Band Optical Repeater System BTS Link-104/108 with SBROU http://www.shyamtelecom.com www.shyamtelecom.com Optical DAS Coverage Solutions 2 BTS Link-104/108 with
REDUTELCO TECHNOLOGY CO.,LTD.
User Manual Wide Band Repeater REDUTELCO TECHNOLOGY CO.,LTD. 2013 January Information in this manual is subject to change without notice http:www.redutelco.com 2009 Redutelco All rights reserved 1 Table
Network Infrastructure Products for Harsh Environments
Salt Fog Qualified Products Network Infrastructure Products for Harsh Environments Network Infrastructure Products for Harsh Environments Microlab s product line for harsh outdoor applications have been
User Manual LTE 4G 850/2600. Wide Dual Band Repeater REDUTELCO TECHNOLOGY CO.,LTD January
User Manual LTE 4G 850/2600 Wide Dual Band Repeater REDUTELCO TECHNOLOGY CO.,LTD. 2015 January Information in this manual is subject to change without notice http:www.redutelco.com 2009 Redutelco All rights
X-Band Redundant LNA Systems
X-Band Redundant LNA Systems LRX-1000 Series Introduction Redundant LNA systems minimize system downtime due to LNA failure by providing a spare LNA and an automatic means of switching to the spare upon
High performance site components
High performance site components Introduction Egant AB is one of the leading suppliers of products for Cellular infrastructure. Specialised in products that makes it possible to share antenna systems,
RECEIVER MULTICOUPLER AND R.F. PRESELECTORS
EMR corp. ELECTROMAGNETIC DESIGNS AND CONSULTING SERVICES FOR THE TWO-WAY COMMUNICATIONS INDUSTRY 22402 N. 19th Avenue - Phoenix, Arizona 85027 Toll Free: 1-800-796-2875 Tel: (623) 581-2875 Fax: (623)
C-Band VSAT Block Up Converters
FEATURES Single box BUC output power levels to 20W RS485 M&C capability Accurate RF Power Monitoring Maintenance Free Operation +24VDC or +48 VDC input voltage OPTIONS Antenna Mounting Kit Form A Summary
RF Components Product Catalogue
RF Components Product Catalogue Government and Defence Broadcast Marine, Oil and Gas SNG and VSAT RF Engineering by Design Contents Splitters / Combiners Active Splitters and Combiners Page 3 Passive Splitters
PASSIVE COMPONENTS PASSIVE COMPONENTS.
PASSIVE COMPONENTS PASSIVE COMPONENTS www.rosenbergerap.com Rosenberger HQ, Bavaria, Germany INTRODUCTION Rosenberger Hochfrequenztechnik GmbH&Co. was founded in Germany in 1958 and ranks among the leading
Precision Test & Measurement Solutions by CCI
Precision Test & Measurement Solutions by CCI Passive Intermodulation...challenging the technology of today s wireless communication systems Passive Intermodulation (PIM) is an undesired, non-linear, signal
Antenna Fiber Boxes. BROADY SOLUTIONS - Tel : +33 (0)
Catalogue 2014 Antenna Fiber Boxes AFB-100 : Single Rx Antenna Fiber Box AFB-100 is designed to modulate radio signal from one receiving antenna to optical SC/APC output. Any passive or active antenna
C-Band Redundant LNA Systems
C-Band Redundant LNA Systems LRC-1000 Series Introduction Redundant LNA systems minimize system downtime due to LNA failure by providing a spare LNA and an automatic means of switching to the spare upon
Technical Manual. Mobile Communication Mini Booster Model: PW-MB or PW-MB10-900
Technical Manual Mobile Communication Mini Booster Model: PW-MB10-800 or PW-MB10-900 PW-MB10-2100 or PW-MB10-1800 Page 1 Table of Contents Introduction Name & Function How to install the system User Attentions
RF Surge Protection. the needs of advanced network applications with technologies such as DC Block, DC Pass and Ultra Low PIM.
RF Surge Protection RF Surge Protection Over forty years ago, PolyPhaser pionieered the market with its patented protection solutions for ever-evolving telecommunication systems. Our proven designs have
Active Antennas: The Next Step in Radio and Antenna Evolution
Active Antennas: The Next Step in Radio and Antenna Evolution Kevin Linehan VP, Chief Technology Officer, Antenna Systems Dr. Rajiv Chandrasekaran Director of Technology Development, RF Power Amplifiers