SUPPLY OF CARRIER PROTECTION COUPLER TYPE NSD-50

Size: px
Start display at page:

Download "SUPPLY OF CARRIER PROTECTION COUPLER TYPE NSD-50"

Transcription

1 (I) GENERAL : Indoor PLCC Equipments are required for important 400KV, 220KV and 132KV Sub/station for Speech, Data Transmission, Protection and Teleprinter Links. (II) GENERAL REQUIREMENT : The equipments shall be of latest components, technology and highly reliable. The equipments offered must have been type tested. (III) SCOPE OF SUPPLY : Protection Couplers NSD-50 with three modules shall be supplied along with fixing channel, required accessories and the terminal blocks fully wired complete in all respect with identification mark. The carrier protection shall be integrated with carrier terminal by just inserting the modules in respective slots of carrier terminal. You will have to impart free training of protection coupler type NSD-50 along with ETL version carrier equipments to at least 3 to 4 telecom engineers of G.E.T.C.O to get acquainted with the technology for our new incumbents. (IV) SPECIFICATION : The equipments to be supplied under this specification shall function satisfactorily under tropical, hot, humid, salty and chemically polluted climatic condition with adverse temperature condition. The equipment shall be manufactured and tested as per latest national or international standard (IS, IEC, CCITT, CIGRE, etc.) whichever is better. This will be clearly brought out by the bidder. The equipments offered shall confirm to, but not limited to following standards. (1) IEC Single sideband Power Line Carrier Terminals. (2) IEC 834-1/ Performance & Testing of teleprotection (Part-I) equipments of Power system - Narrow band Command system. (3) IEC / Environmental Testing Part-2 Tests section-3 Test Ca: Damp heat steady state. In addition to the above, the carrier Protection coupler shall be manufactured and supplied detailed as under: GETCO/E/TS-PLCC 03403/R0, Dt: Page 1 of 11

2 (IV)(A) TELE PROTECTION EQUIPMENT : The bidder shall offer Teleprotection Equipment which works on coded and un-coded signal principle for transmission/reception of protection signal detailed as under. The equipment shall be suitable for; connection to the Power line carrier terminal for remote end tripping/blocking on permissive and Direct Tripping signals to be transmitted through single PLCC Channel. The requirement is as under: - (a) Teleportation Equipment with 4 commands. It should be suitable for permissive and direct trip carrier aided protection scheme. The command should be either All coded OR Two coded + Two uncoded commands. It should work in full-duplex mode for both 2/4-command versions. The Tele-Protection Equipment shall have provision for: - Signal Inputs/Outputs No. of starting inputs No. of command inputs Command O/P using solid state relays Command O/P for unblocking outputs Condition Requirement Two Command Equipment Four Command Equipment (D.C. Isolated 48V- 250V DC & <10 ma 2 4 DC isolated, N/O contact 250VDC, <2A N/O contact 250V DC, 10W 2 4 Alarm Outputs 250V D.C.150 Watts 4 * 4 * Counters Separate for each Tx and Rx Commands Power supply Working from PLC Terminal 48V DC (+ 20%,- 15%) * 2 Common alarms, N/O OR N/C contact 1 Transmitter alarm, N/O contact 1 Receiver alarm, N/O contact GETCO/E/TS-PLCC 03403/R0, Dt: Page 2 of 11

3 The network protection signaling equipment shall not be only insensitive to corona noise, but shall also remain unaffected by impulse type noises which are generated by electrical discharge and by the opening and closing of circuit breakers, isolators, earthing switches etc. In the offer, bidder shall clearly explain as to what measures have been taken to make the equipment insensitive to corona noise, white noise and to impulse noise of amplitude larger than the wanted signal and submit full test reports. The equipment shall be unaffected by spurious tripping signals. The Bidder shall submit proof as to how this is achieved satisfactorily. The equipment shall be suitable for transmission of direct and permissive trip signal for protection of power lines and Sub-station Equipments. The equipment shall operate in the audio frequency range in speech band (0 to 2000 HZ). The protection signaling equipment shall be of solid-state design, modular in construction and have a proven operating record in similar application over EHV systems, with motherboard construction. The carrier protection channels shall be engineered in such a manner that time interval between receipt of a tripping/blocking command from the protection relays on the transmit side by its transmission over the carrier link, reception at the far end and giving of the commands to trip relays at the distance end shall not exceed 20 msec for permissive tripping and 30 msec. for direct tripping even for the longest line section. Operating time lower than specified above may be preferred provided they fulfill the requirements of security and reliability as below & also meet the requirement of the standard IEC first edition 1988 & latest amendment if any. For For Permissive Trip Direct Trip (Uncoded) (Coded) False - Trip probability < 2x10-4 < (Noise burst of any amplitude) Fail to trip probability < 5x10-1 < 10-2 For S/N 6db in 4 khz Band (White Noise Measurement) It may be emphasized that specified time, as mentioned above, is composed of the following: (a) Back - to - Back signal delay in Frequency shift or coded signal protection equipment. (b) Back - to - Back delay in PLC terminal. (c) Delay in transmission line. GETCO/E/TS-PLCC 03403/R0, Dt: Page 3 of 11

4 (d) Operation time of inter posing relay, if any, frequency shift or coding equipment. It has to be ensured that under no circumstance protection channel should share the power. Each protection channel shall be able to transmit power for which system is designed. For example, a 20 W PLC terminal shall transmit 20 watt (max) for protection channel alone in the event of fault. Speech and superimposed data channels, in the same protection terminal must get disconnected momentarily during the protection signaling transmission. The equipment shall be constructed such that in permissive line protection system, operational reliability of the protection channel may be checked over the carrier link from end to end and by means of a loop test. It shall be possible to carry out the above tests from either end of the carrier link. During healthy condition of the transmission line, the loop test shall not initiate a tripping command. In the event of a system fault, while loop test is in progress, protection signal shall over ride the test signal. In the receiver section of Carrier protection signaling equipment the FSK signal shall be converted in to the coded pulses (i.e Bit Pattern) and evaluated digitally before giving final output command to tripping relays or relay protection equipments to achieve high dependability and security and also to provide reliability against false trip and loosing commands even under adverse channel condition. The equipment shall be complete with built - in Digital counters for counting the number of trip commands sent and number of trip commands received separately for each channel. The equipment shall be mounted inside the Carrier Terminal and shall be fully wired with, contactor units, tag blocks etc., and ready for commissioning. The bidder shall clearly indicate and describe the facility/items provided in the equipment in details. Any ambiguity or omission will mean that the particular facility or module etc., is not provided in the equipment. It shall meet the entire environmental requirement as that of carrier terminal. While transmitting protection signals the protection coupler shall cut off the speech and other less important channels and thereby the entire GETCO/E/TS-PLCC 03403/R0, Dt: Page 4 of 11

5 power of carrier terminal should be made available for transmission of protection signals. It should be brought out that the protection equipment should perform satisfactorily under noisy condition. The bidder shall indicate the guaranteed technical particulars of the equipment offered in Schedule - 'B'. A Schedule of deviation shall be attached separately for Teleprotection equipment in the form of Schedule - 'B/1'. (V) CONFIGURATION: The Configuration of Carrier Protection Coupler, Type NSD-50 shall have following different cards/prints. G4AA : DSP Module NSD 50 G4AC : Interface NSD 50 ( 2 Modules) PREQUALIFICATION REQUIREMENTS : 1. The bidder shall be Original Equipment Manufacturer of the Protection Coupler. The offered equipments should have been designed, manufactured and tested as per relevant IS/IEC Standards with latest amendments. 2. The bidder should indicate manufacturing capacity by submitting fresh certificate of a Chartered Engineer (CE). 3. Equipment proposed to be supplied by bidder of similar or higher rating shall be in service for a minimum period of THREE (3) years. The Satisfactory performance certificate of corporate office of respective utilities should be submitted. 4. The bidder should clearly indicate the quantity and single value contract executed during last FIVE (5) years, for the offered equipment. The details of past supplies should cover, i) Same rated equipment as Offered supplied to GETCO (Erstwhile known as GEB). ii) Higher rated equipment than Offered supplied to GETCO (Erstwhile known as GEB). iii) Same rated equipment as Offered supplied to other Utilities. 5. The bidder shall furnish the copies of type test reports for the Carrier protection Coupler not more than FIVE years old. Equipment Offered shall have all Valid Type Test Certificate from NABL accredited or GETCO/E/TS-PLCC 03403/R0, Dt: Page 5 of 11

6 International Laboratory. The Validity of Type Test report is 5 Years from the Date of Type Test Report. 6. The bidder shall furnish the full technical details & drawings for the Carrier terminal offered. 7. The bidder shall have the experience of at least 10 years of manufacture & supply of similar type of Carrier terminals. 8. The bidder shall furnish the full details of the orders executed. 9. Any deviation shall be clearly indicated separately. 10. The GETCO reserves right to increase or decrease the quantity at the time of placing the order. 11. The GETCO reserve right either to accept or reject any of the offers Without assigning the reason. (VI) TYPE TESTS: Valid type test reports not more than 5 Years old performed for following tests shall be submitted with the offer with all supporting result sheets and reference documents with List of Type Tests in Performa- X Given here under. Performa X: Sr.No. Test Equipment Description of test conducted Standard/ Clause Test report No. & Name of test laboratory Remarks All tests of carrier terminal Insulation test Impulse withstand Power supply variations Interruption test LF disturbance emission Reverse polarity Transmission time Interference by discrete frequency Checking of alarm functions Security Dependability Interference by frequency deviation Multi command equipment GETCO/E/TS-PLCC 03403/R0, Dt: Page 6 of 11

7 (VII) Drawings: Following Drawings shall be submitted with the offer. Module Layout For ETL 41+ NSD 50 : Unit Arrangement Cabinet Layout For ETL 41 + NSD 50 Wiring Diagram For ETL 41 + NSD 50 Cable Complete V9LB Cable Complete V9LC GETCO/E/TS-PLCC 03403/R0, Dt: Page 7 of 11

8 S C H E D U L E - 'B' General Data and Guaranteed Technical Particulars Teleprotection Equipment. No. System Particular GTP of offered equipment 1. MAKE and Type of Protection Equipment 2. No. of Commands: - Uncoded - Coded - Altogether 3. Test signal frequency(loop test) 4. Trip signal frequencies 5. Guard frequency 6. Command duration 7. Signal evaluation time 8. Nominal transmission times Including PLC equipment Delay & relay operating times * Nominal transmission time for - Uncoded - Coded 9. Security: False Trip Probability: 10. Dependability: Fail to Trip Probability For S/N of 6 db : 11. Unblocking operating time 12. Power supply 13. Ambient condition 14. Transmitter Module: Level - Guard signal PLC Pilot Or separate guard signal - Normal tripping signal - Test signal Spurious signal suppression Signal boosting 15. Receiver Module Level - Guard Signal - Normal tripping signal - Test signal GETCO/E/TS-PLCC 03403/R0, Dt: Page 8 of 11

9 S C H E D U L E - 'B' General Data and Guaranteed Technical Particulars Teleprotection Equipment. No. System Particular GTP of offerred equipment Dynamic range - Minimum level - Maximum level 16. Guard Signal frequency Programmable Standard setting 17. Nos. & type of Alarm outputs With voltage & current ratings. 18 Nos. & type of starting inputs 19. Nos. of type of command inputs 20. Method of tripping 21. Rated battery voltage and current Rating 22. Nos. & type of command outputs With voltage & current rating & Operating time. 23. Nos. & type of unblocking outputs With rated voltage, current limit & Operating time. 24. Transmission time and command Prolongation period for - Permissive Trip - Direct Trip 25. Trip Counters - display type - range - Standby supply Endurance GETCO/E/TS-PLCC 03403/R0, Dt: Page 9 of 11

10 S C H E D U L E ' B/1 (To be filled in and signed by the Tenderer) Schedule of deviations from Technical Specifications for. We / I have carefully gone through the Technical Specification and we / I have satisfied ourselves / myself and hereby confirm that our / my offer strictly confirm to the requirements of the Technical Specification except for the deviations given below : Sr.No. Description Stipulations in specification Deviation Offered Remarks Signature : Name of Authorized signatory of the company : Name of the tendering Company Date : Place: GETCO/E/TS-PLCC 03403/R0, Dt: Page 10 of 11

11 SCHEDULE OF REQUIREMENTS OF ABB MAKE NSD-50 PROTECTION COUPLER Sr.No. Description Quantity 1. Protection coupler Type NSD-50, Nos. Make: ABB suitable for four command (with 3 modules) transmission arrangement. GETCO/E/TS-PLCC 03403/R0, Dt: Page 11 of 11

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR PLCC TERMINAL WITH Page 1 of 19 (A) SPECIAL INSTRUCTIONS TO BIDDER Please

More information

Utility Communications Teleprotection Equipment TPT-200

Utility Communications Teleprotection Equipment TPT-200 Utility Communications Teleprotection Equipment TPT-200 5C Communications Inc. All rights reserved Teleprotection is designed to transfer protection commands coming, in most cases, from distance protection

More information

GENERAL TECHNICAL SPECIFICATION (Turnkey Work)

GENERAL TECHNICAL SPECIFICATION (Turnkey Work) GENERAL TECHNICAL SPECIFICATION (Turnkey Work) March 2015 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar,

More information

VI 3 - i TABLE OF CONTENTS

VI 3 - i TABLE OF CONTENTS VI 3 - i TABLE OF CONTENTS 3 PROJECT SPECIFIC DATA... 1 3.1 DEFINITIONS... 1 3.1.1 Design Data, High and Medium Voltage... 1 3.1.2 Design Data, Low Voltage Equipment... 2 3.1.3 Phase Relationship... 3

More information

1.0 mh, 3150 A LINE TRAP

1.0 mh, 3150 A LINE TRAP GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR 1.0 mh, 3150 A LINE TRAP GETCO/E/TS-400KV WT 0904/R0, Dt: 09.01.2012

More information

SWT 3000 Teleprotection technical data siemens.com

SWT 3000 Teleprotection technical data siemens.com Power network telecommunication SWT 3000 Teleprotection technical data siemens.com Sustainable success for high-voltage power networks The SWT 3000 Teleprotection system has been the first choice for reliable

More information

LICENSING GUIDELINES AND PROCEDURES FOR SHORT-RANGE RADIO SERVICE (SRRS). For the purpose of this Circular, the following terms are defined hereunder:

LICENSING GUIDELINES AND PROCEDURES FOR SHORT-RANGE RADIO SERVICE (SRRS). For the purpose of this Circular, the following terms are defined hereunder: MEMORANDUM CIRCULAR NO. 01-01-98 SUBJECT: LICENSING GUIDELINES AND PROCEDURES FOR SHORT-RANGE RADIO SERVICE (SRRS). Pursuant to the provisions of Republic Act No.7925 Act No. 3846 as amended, Executive

More information

TECHNICAL SPECIFICATION OF LT SHACKLE BOLT (G. I. BOLT) WITH NUT AND SPRING WASHER

TECHNICAL SPECIFICATION OF LT SHACKLE BOLT (G. I. BOLT) WITH NUT AND SPRING WASHER TECHNICAL SPECIFICATION OF LT SHACKLE BOLT (G. I. BOLT) WITH NUT AND SPRING WASHER 1.0 SCOPE: This specification covers the manufacture, testing at works and supply of G. I. Bolts with Nut and Spring Washer

More information

POWER LINE CARRIER UCC 2021

POWER LINE CARRIER UCC 2021 POWER LINE CARRIER SPECIAL FEATURES UCC 2021 Flexibility for upgrade of existing PLC networks (100% compatible with existing PA and Line Interface modules of Analog GE PLC equipments) Interconnection between

More information

TECHNICAL SPECIFICATION

TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION 1. SCOPE : TECHNICAL SPECIFICATION FOR LIGHTNING ARRESTORS 1.1. This Specification covers design, manufacture, testing at manufacturer's Works, packing, supply, delivery of 42 KV

More information

M9606. FSK Modem. 5C Communications Inc.

M9606. FSK Modem. 5C Communications Inc. FSK Modem Application modem is a voice-frequency telegraphy unit (VFT unit) which operates according to the principle of binary frequency shift keying. It is designed especially for Power Industrial applications.

More information

36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE)

36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEB STANDARD 022 : 1994 Specification for 36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEYLON ELECTRICITY BOARD SRI LANKA Specification for 36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEB Standard 022 : 1994

More information

Hands On Relay School 2017

Hands On Relay School 2017 Hands On Relay School 2017 RFL Electronics Inc. www.rflelect.com PLC Teleprotection 2 Application of TPS PLC IEEE Std 643 2004 The PLC uses the Power lines to transmit and receive signals from station

More information

10. DISTURBANCE VOLTAGE WITHSTAND CAPABILITY

10. DISTURBANCE VOLTAGE WITHSTAND CAPABILITY 9. INTRODUCTION Control Cabling The protection and control equipment in power plants and substations is influenced by various of environmental conditions. One of the most significant environmental factor

More information

SOLUTIONS FOR AN EVOLVING WORLD RFL Programmable FSK Powerline carrier system

SOLUTIONS FOR AN EVOLVING WORLD RFL Programmable FSK Powerline carrier system SOLUTIONS FOR AN EVOLVING WORLD RFL 9780 Programmable FSK Powerline carrier system Your world is changing and so are we. At RFL, we know your needs change much faster than your infrastructure. Our comprehensive

More information

Hamdy Faramawy Senior Application Specialist ABB Sweden

Hamdy Faramawy Senior Application Specialist ABB Sweden Design, Engineering and Application of New Firm Capacity Control System (FCCS) Mohammed Y. Tageldin, MSc. MIET Senior Protection Systems Engineer ABB United Kingdom mohammed.tageldin@gb.abb.com Hamdy Faramawy

More information

GENERAL TECHNICAL SPECIFICATION

GENERAL TECHNICAL SPECIFICATION GENERAL TECHNICAL SPECIFICATION September 2017 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar, Kolkata 700091.

More information

Table of Contents. Introduction... 1

Table of Contents. Introduction... 1 Table of Contents Introduction... 1 1 Connection Impact Assessment Initial Review... 2 1.1 Facility Design Overview... 2 1.1.1 Single Line Diagram ( SLD )... 2 1.1.2 Point of Disconnection - Safety...

More information

VHF LAND MOBILE SERVICE

VHF LAND MOBILE SERVICE RFS21 December 1991 (Issue 1) SPECIFICATION FOR RADIO APPARATUS: VHF LAND MOBILE SERVICE USING AMPLITUDE MODULATION WITH 12.5 khz CARRIER FREQUENCY SEPARATION Communications Division Ministry of Commerce

More information

communication networks Power Line Carrier Communication. Design and Engineering.

communication networks Power Line Carrier Communication. Design and Engineering. communication networks Power Line Carrier Communication. Design and Engineering. 2 3 An existing PLC network represents a considerable investment made over many years. In spite of the growing significance

More information

TECHNICAL SPECIFICATION FOR 22 KV CURRENT TRANSFORMERS

TECHNICAL SPECIFICATION FOR 22 KV CURRENT TRANSFORMERS GUJARAT ENERGY TRANSMISSION CORPORATION LTD. CIRCLE OFFICE, NADIAD TECHNICAL SPECIFICATION FOR 22 KV CURRENT TRANSFORMERS SPECIAL INSTRUCTIONS TO BIDDER Please read following instructions carefully before

More information

NAME OF (VENDOR/MANUFACTURER) Clause No. Clause Description Comments, if any Remarks, if any

NAME OF (VENDOR/MANUFACTURER) Clause No. Clause Description Comments, if any Remarks, if any BSNL seeks comments on Draft GR for UPS from UPS/Invertors vendors BSNL INVITES COMMENTS FROM UPS / INVERTOR VENDORS ON DRAFT GR FOR UPS PREPARED BY BSNL. COMMENTS MAY BE GIVEN TO BSNL CORPORATE OFFICE,

More information

ASHIDA Numerical 3OC + 1EF Protection Relay

ASHIDA Numerical 3OC + 1EF Protection Relay PROTH. ERR L5 PKP FAULT DT REC LOCK BF L6 L7 CLOSE TRIP ADR 241B Protection Features : 4 Element (3 Phase + EF + Sensitive EF) Over current IDMT/DMT with instant trip. Programmable (Non- Volatile) Setting

More information

SOLUTIONS FOR AN EVOLVING WORLD RFL DSP Powerline Carrier System

SOLUTIONS FOR AN EVOLVING WORLD RFL DSP Powerline Carrier System SOLUTIONS FOR AN EVOLVING WORLD RFL 9508 DSP Powerline Carrier System Your world is changing and so are we. At RFL, we know your needs change much faster than your infrastructure. Our comprehensive line

More information

The RSM shall be extensively used in field & laboratory for verification of the accuracy of all types of single-phase energy meters.

The RSM shall be extensively used in field & laboratory for verification of the accuracy of all types of single-phase energy meters. TECHNICAL SPECIFICATION FOR PORTABLE ELECTRONIC REFERENCE STANDARD METER (ERS) FOR TESTING OF SINGLE PHASE KILOWATT HOUR ENERGY METERS (ACCURACY CLASS 0. 2) 1. SCOPE: The specification covers the requirement

More information

AC CURRENT GENERATOR POC-6000 (current from 0 to 1000 ARMS)

AC CURRENT GENERATOR POC-6000 (current from 0 to 1000 ARMS) AC CURRENT GENERATOR PERFORMANCES Wide range of current 50 db dynamic range Signal-to-noise ratio: 80 db open loop protection Stability < 0,1% Very low THD distortion < 0,3% External synchronization Build-up

More information

PROTECTION SIGNALLING

PROTECTION SIGNALLING PROTECTION SIGNALLING 1 Directional Comparison Distance Protection Schemes The importance of transmission system integrity necessitates high-speed fault clearing times and highspeed auto reclosing to avoid

More information

POWER LINE CARRIER COMMUNICATION

POWER LINE CARRIER COMMUNICATION POWER LINE CARRIER COMMUNICATION September 2017 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar, Kolkata 700091.

More information

Maharashtra State Electricity Distribution Co. Ltd.

Maharashtra State Electricity Distribution Co. Ltd. Maharashtra State Electricity Distribution Co. Ltd. SPECIFICATION NO. MSEDCL/ DIST:MSC-III/LT CAP/1/2009/R2(071009) SPECIFICATIONS FOR APP TYPE L.T. CAPACITOR UNITS OF 25 / 30 KVAR CAPACITY (FOR 63 / 100

More information

ASHIDA Numerical OC/EF Protection Relay

ASHIDA Numerical OC/EF Protection Relay ASHIDA Numerical OC/EF Protection Relay Features: 4 Element (3 Phase + EF) over current IDMT with instant trip. Back - lit LCD display for settings. Display of fault current. / Load current. Selection

More information

Proposal Evaluation Methodology. For Narrow Band Power Line Carrier Equipment

Proposal Evaluation Methodology. For Narrow Band Power Line Carrier Equipment Proposal Evaluation Methodology )PEM( For Narrow Band Power Line Carrier Equipment Spec: 01-17 Ver: 2 Prepared Checked Approved Name Sh. Shabi L. Dubrovski M. Koritny T. Honovich Date Signature 1 1. General

More information

) #(2/./53 $!4! 42!.3-)33)/.!4! $!4! 3)'.!,,).' 2!4% ()'(%2 4(!. KBITS 53).' K(Z '2/50 "!.$ #)2#5)43

) #(2/./53 $!4! 42!.3-)33)/.!4! $!4! 3)'.!,,).' 2!4% ()'(%2 4(!. KBITS 53).' K(Z '2/50 !.$ #)2#5)43 INTERNATIONAL TELECOMMUNICATION UNION )454 6 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU $!4! #/--5.)#!4)/. /6%2 4(% 4%,%(/.%.%47/2+ 39.#(2/./53 $!4! 42!.3-)33)/.!4! $!4! 3)'.!,,).' 2!4% ()'(%2 4(!.

More information

Director General Engineering, Planning and Standards Branch (JETN, Room 1943B) Industry Canada 235 Queen Street, Ottawa, Ontario, K1A 0H5

Director General Engineering, Planning and Standards Branch (JETN, Room 1943B) Industry Canada 235 Queen Street, Ottawa, Ontario, K1A 0H5 340 Albert St Suite 1300 Ottawa, ON K1R 7Y6 BY EMAIL to Spectrum.engineering@ic.gc.ca Director General Engineering, Planning and Standards Branch (JETN, Room 1943B) Industry Canada 235 Queen Street, Ottawa,

More information

071-3: 2009 CEB SPECIFICATION

071-3: 2009 CEB SPECIFICATION 071-3: 2009 CEB SPECIFICATION PROGRAMMABLE POLY PHASE METERING EQUIPMENT - CT CONNECTED CEYLON ELECTRICITY BOARD SRI LANKA Specification for PROGRAMMABLE POLY PHASE CT CONNECTED METERING EQUIPMENT ACCURACY

More information

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units BETA Switching Transformers, Bells and Socket Outlets /2 Product overview /3 4AC3 0, 4AC3 1 bell transformers /5 4AC3 4... 4AC3 transformers for permanent loads /8 4AC2 4 power supply units / 7LQ2 2 bells

More information

Smart Termination TECHNICAL SPECIFICATIONS CURRENT VOLTAGE INSTRUMENTRANSFORMER

Smart Termination TECHNICAL SPECIFICATIONS CURRENT VOLTAGE INSTRUMENTRANSFORMER Customer : REV. 0 Page 1/16 Smart Termination TECHNICAL SPECIFICATIONS CURRENT VOLTAGE INRUMENTRANSFORMER CVS - 24 - G - Revision Prepared Description Checked by Rev. Date by 0 13/06/16 First issue E.

More information

Technical Specification. for 1.1 KV Copper Control Cable

Technical Specification. for 1.1 KV Copper Control Cable WEST BENGAL STATE ELECTRICITY DISTRIBUTION COMPANY LIMITED (A Govt. of West Bengal Enterprise) Office of the Chief Engineer, Procurement & Contracts Department Vidyut Bhavan, 4 th. floor, Bidhannagar,

More information

Suppliers' Information Note. BT Metallic Path Facility. Interface Description

Suppliers' Information Note. BT Metallic Path Facility. Interface Description SIN 349 Issue 2.5 August 2015 Suppliers' Information Note For The BT Network BT Metallic Path Facility Interface Description Each SIN is the copyright of British Telecommunications plc. Reproduction of

More information

TEST SUMMARY. Prüfbericht - Nr.: Test Report No.: Seite 2 von 27. Page 2 of 27

TEST SUMMARY. Prüfbericht - Nr.: Test Report No.: Seite 2 von 27. Page 2 of 27 15072768 001 Seite 2 von 27 Page 2 of 27 TEST SUMMARY 4.1.1 HARMONICS ON AC MAINS 4.1.2 VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER ON AC MAINS 4.1.3 MAINS TERMINAL CONTINUOUS DISTURBANCE VOLTAGE

More information

The power line carrier equipment will provide speech, telecontrol and teleprotection channels over 50 Hz, 132 KV transmission systems.

The power line carrier equipment will provide speech, telecontrol and teleprotection channels over 50 Hz, 132 KV transmission systems. National Electric Power Company Telecommunication and Control Department Supply of Outdoor Coupling Equipments ( Line Traps and Coupling Filters ) Tender No. 8/2018 A) General NEPCO is extending the transmission

More information

Technical Equipment Specification

Technical Equipment Specification STATE OF CALIFORNIA Office of the State Chief Information Officer Public Safety Communications Division Technical Equipment Specification Equipment Type: Transmitter/Receiver Mobile Relay/Base/Control

More information

SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem

SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1993 Specifications CSJ s 0902-48-442 & 0902-48-432 SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1. General. This Item shall govern for the furnishing and installation of Spread Spectrum Wireless

More information

Overcurrent Protection / 7SJ45

Overcurrent Protection / 7SJ45 Overcurrent Protection / SJ SIPROTEC easy SJ numerical overcurrent protection relay powered by CTs Fig. / Description SIPROTEC easy SJ numerical overcurrent protection relay powered by current transformers

More information

ETSI ES V1.2.1 ( )

ETSI ES V1.2.1 ( ) ES 201 235-4 V1.2.1 (2002-03) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 4: Transmitters and Receivers for use in Terminal Equipment

More information

THE KENYA POWER AND LIGHTING CO. LTD. SPECIFICATIONS for IMPULSE VOLTAGE TEST EQUIPMENT

THE KENYA POWER AND LIGHTING CO. LTD. SPECIFICATIONS for IMPULSE VOLTAGE TEST EQUIPMENT THE KENYA POWER AND LIGHTING CO. LTD SPECIFICATIONS for IMPULSE VOLTAGE TEST EQUIPMENT NAME DESIGNATION SIGNATURE DATE Compiled by Ephantus Nyagah Ag. Senior Engineer Checked by Eng. Thagichu Kiiru Deputy

More information

SPECIAL SPECIFICATION 6744 Spread Spectrum Radio

SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 1. Description. Furnish and install spread spectrum radio system. 2. Materials. Supply complete manufacturer specifications

More information

Technical Specifications for Portable 3-Ø Power Analyzer

Technical Specifications for Portable 3-Ø Power Analyzer Technical Specifications for Portable 3-Ø Power Analyzer SCOPE: This specification covers the general specifications of 3-phase power analyzer that can be used to measure the no load and full load losses

More information

Maharashtra State Electricity Distribution Co. Ltd.

Maharashtra State Electricity Distribution Co. Ltd. Maharashtra State Electricity Distribution Co. Ltd. Draft SPECIFICATION NO. MSEDCL/ DIST:MSC-III/LT MPP CAP/11/2009/R0 SPECIFICATIONS FOR MPP TYPE L.T. CAPACITOR UNITS OF 25 / 30 KVAR CAPACITY (FOR 63

More information

COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS

COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS 006: 2008 CEB SPECIFICATION COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS CEYLON ELECTRICITY BOARD SRI LANKA Specification for COMBINED METERING TRANSFORMERS (OUTDOOR TYPE) FOR

More information

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand

More information

INTERNATIONAL TELECOMMUNICATION UNION DATA COMMUNICATION NETWORK: INTERFACES

INTERNATIONAL TELECOMMUNICATION UNION DATA COMMUNICATION NETWORK: INTERFACES INTERNATIONAL TELECOMMUNICATION UNION CCITT X.21 THE INTERNATIONAL (09/92) TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE DATA COMMUNICATION NETWORK: INTERFACES INTERFACE BETWEEN DATA TERMINAL EQUIPMENT

More information

GENERAL CONSIDERATIONS ON TRANSMULTIPLEXING EQUIPMENTS. (Geneva, 1980; further amended)

GENERAL CONSIDERATIONS ON TRANSMULTIPLEXING EQUIPMENTS. (Geneva, 1980; further amended) 5i 7.9 Other terminal equipments Recommendation G.791 GENERAL CONSIDERATIONS ON TRANSMULTIPLEXING EQUIPMENTS (Geneva, 1980; further amended) The CCITT, considering the advantages offered in some cases

More information

TS RES - OUTSTANDING ISSUES

TS RES - OUTSTANDING ISSUES TS RES - OUTSTANDING ISSUES This document has been officially issued as DRAFT until the following outstanding issues have been resolved. At that time the document will be officially reissued as the next

More information

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Aggregated Generating Facilities Technical Requirements

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Aggregated Generating Facilities Technical Requirements Division 502 Technical Applicability 1(1) Section 502.1 applies to: Expedited Filing Draft August 22, 2017 the legal owner of an aggregated generating facility directly connected to the transmission system

More information

KENYA ELECTRICITY GENERATING COMPANY LTD

KENYA ELECTRICITY GENERATING COMPANY LTD KENYA ELECTRICITY GENERATING COMPANY LTD TENDER No. KGN-HYD-014-2016 TENDER FOR REHABILITATION OF PROTECTION EQUIPMENT FOR MASINGA HYDRO POWER STATION 20/06/2016 ADDENDUM NO. 1 In accordance with the tender

More information

012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION)

012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION) 012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 8051 Fax: +94 11 232 5387 CONTENTS Page 1.0

More information

Device Under Test: ALTEA VS- 24-I VS-24-I. 0 24/09/12 First issue A. Peretto L. Peretto 1 24/06/16 All text review E. Scala L. Peretto J. L.

Device Under Test: ALTEA VS- 24-I VS-24-I. 0 24/09/12 First issue A. Peretto L. Peretto 1 24/06/16 All text review E. Scala L. Peretto J. L. /9 TECHNICAL SPECIFICATIONS VOLTAGE LOW-POWER TRANSFORMER VS- Rev. Date Revision Description Prepared by Checked by Approved by 0 24/09/2 First issue A. Peretto L. Peretto 24/06/6 All text review E. Scala

More information

EMC Test Report. Report Number: M030826

EMC Test Report. Report Number: M030826 Page 1 of 36 EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: melb@emctech.com.au EMC Test Report Report

More information

TECHNICAL GUIDELINES FOR FM BROADCAST STANDARDS

TECHNICAL GUIDELINES FOR FM BROADCAST STANDARDS TECHNICAL GUIDELINES FOR FM BROADCAST STANDARDS Directorate of Technical Regulations February 2014 94, Kairaba Avenue, P. O. Box 4230 Bakau, The Gambia Tel. (220) 4399601 / 4399606 Fax: (220) 4399905 EMail:

More information

HI-Physix Laboratory, L-83, Sector-1, DSIDC Industrial Area, Bawana, Delhi. Discipline Electronics Testing Issue Date

HI-Physix Laboratory, L-83, Sector-1, DSIDC Industrial Area, Bawana, Delhi. Discipline Electronics Testing Issue Date Last Amended on - Page 1 of 14 I. AUDIO EQUIPMENT 1. Audio-Video and Similar Electronics Apparatus Safety Requirement Marking & Instructions Laser Radiation (Products Marked Class I only) Heating under

More information

Southern Company Interconnection Requirements for Inverter-Based Generation

Southern Company Interconnection Requirements for Inverter-Based Generation Southern Company Interconnection Requirements for Inverter-Based Generation September 19, 2016 Page 1 of 16 All inverter-based generation connected to Southern Companies transmission system (Point of Interconnection

More information

PROCEDURE FOR INSPECTION OF ELECTRICAL INSTALLATIONS ABOVE 250KVA

PROCEDURE FOR INSPECTION OF ELECTRICAL INSTALLATIONS ABOVE 250KVA PROCEDURE FOR INSPECTION OF ELECTRICAL INSTALLATIONS ABOVE 250KVA Generally inspection of electrical installations is carried out under Regulation-30 (Periodical inspection & testing) & Regulation-43 (Approval

More information

SC1000 DGPS USCG Dual Transmitter

SC1000 DGPS USCG Dual Transmitter Southern Avionics Company's DGPS Reference Station Transmitter System. Model: SC1000 DUAL USCG SC1000 DGPS USCG Dual Transmitter QUALIFICATIONS: Meets applicable requirements of the United States Coast

More information

CAPACITOR VOLTAGE TRANSFORMER

CAPACITOR VOLTAGE TRANSFORMER CAPACITOR VOLTAGE TRANSFORMER March 2015 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office VidyutBhawan, Block DJ, Sector-II, Bidhannagar, Kolkata 700091. CIN

More information

ECREE OF THE DIRECTOR GENERAL OF POST AND TELECOMMUNICATION NUMBER: 171/DIRJEN/2009

ECREE OF THE DIRECTOR GENERAL OF POST AND TELECOMMUNICATION NUMBER: 171/DIRJEN/2009 1 ECREE OF THE DIRECTOR GENERAL OF POST AND TELECOMMUNICATION NUMBER: 171/DIRJEN/2009 ON TECHNICAL REQUIREMENTS OF TOOLS AND EQUIPMENT OF HF, VHF, AND UHF COMMUNICATION RADIO BY THE GRACE OF GOD THE ALMIGHTY

More information

PROXIMITY SENSOR TERMINOLOGY

PROXIMITY SENSOR TERMINOLOGY Never use this desk reference for installation or operation of equipment. Refer to manual for installation and operation instructions. The following descriptions refer to the European standard EN 60947-5-2.

More information

PLC-K506 Series FEATURES DESCRIPTION FEATURES

PLC-K506 Series FEATURES DESCRIPTION FEATURES FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate With Up to 32 Devices DESCRIPTION

More information

Coast and Ship Station Single Sideband Radiotelephone Transmitters and Receivers Operating in the 1,605-28,000 khz Band

Coast and Ship Station Single Sideband Radiotelephone Transmitters and Receivers Operating in the 1,605-28,000 khz Band Issue 1 April 1, 1971 Spectrum Management Radio Standards Specification Coast and Ship Station Single Sideband Radiotelephone Transmitters and Receivers Operating in the 1,605-28,000 khz Band Aussi disponible

More information

satech SynchroStar GPS 200 Series

satech SynchroStar GPS 200 Series satech SynchroStar GPS 200 Series KEY BENEFITS Designed with high quality oscillator OCXO the device is characterized by superior frequency stability and improved holdover performance that allows maintaining

More information

Type: ADR233A (ADITYA V2 Series) (Preliminary) ASHIDA Numerical 3 Phase Tx. Differential Protection Relay

Type: ADR233A (ADITYA V2 Series) (Preliminary) ASHIDA Numerical 3 Phase Tx. Differential Protection Relay Ashida Numerical 3 Directional Phase Tx. 3O/C Differential + 1E/F Protection PROTH. ERR FAULT 87 L5 L6 REF L7 BF TRIP ADR 233B_V2 233A_V2 Protection Features: 3Phase Tx. Differential Protection + REF Programmable

More information

TECHNICAL SPECIFICATION FOR 11KV, 3C x95mm mm 2 AERIAL BUNCHED CABLES FOR OVERHEAD LINES (CROSSED LINKED POLYTHENE DRY GAS CURED)

TECHNICAL SPECIFICATION FOR 11KV, 3C x95mm mm 2 AERIAL BUNCHED CABLES FOR OVERHEAD LINES (CROSSED LINKED POLYTHENE DRY GAS CURED) TECHNICAL SPECIFICATION FOR 11KV, 3C x95mm 2 + 80mm 2 AERIAL BUNCHED CABLES FOR OVERHEAD LINES (CROSSED LINKED POLYTHENE DRY GAS CURED) 1. SCOPE This specification covers requirements of, 3C x95mm 2 +

More information

PURCHASE DIVISION DEPARTMENT QUALITY MANUAL Revision No. : 02 Issue No: : 2 Dt of Revision : Issue Dt. :

PURCHASE DIVISION DEPARTMENT QUALITY MANUAL Revision No. : 02 Issue No: : 2 Dt of Revision : Issue Dt. : Section : 0 Document : DQM-01 Topic : FORMAT 6 OF PROCUREMENT PROCEDURE OF CPRI (NON-WORKS) Section I(B)-Technical Specification Tender Enquery No PUR/UARC-02/14-15 Name of the Equipment: Damped Oscillatory

More information

ALP-UDR Universal Detection Relay user-defined protection, automation, and monitoring

ALP-UDR Universal Detection Relay user-defined protection, automation, and monitoring ALP-UDR Universal Detection Relay user-defined protection, automation, and monitoring The first Real-Time Protection and Automation platform that can be adapted to a wide variety of applications. While

More information

TECHNICAL SPECIFICATION OF UNIVERSAL TYPE COMBINED THREE PHASE & SINGLE PHASE PORTABLE ELECTRONIC REFERENCE STANDARD METER CAPABLE OF TESTING OF ALL

TECHNICAL SPECIFICATION OF UNIVERSAL TYPE COMBINED THREE PHASE & SINGLE PHASE PORTABLE ELECTRONIC REFERENCE STANDARD METER CAPABLE OF TESTING OF ALL TECHNICAL SPECIFICATION OF UNIVERSAL TYPE COMBINED THREE PHASE & SINGLE PHASE PORTABLE ELECTRONIC REFERENCE STANDARD METER CAPABLE OF TESTING OF ALL 1.0 Scope: TYPE OF HT AND LT METERS This specification

More information

G-8945 TRANSFER-TRIP SYSTEM

G-8945 TRANSFER-TRIP SYSTEM T om or r ow 's T el em et r y T od a y! Da-Tel Research Company, Inc. Phone: (970) 249-6129 932 N. Park Avenue / P. O. Box 1206 Fax: (970) 249-8919 Montrose, Colorado 81402 www.da-telresearch.com Email:

More information

ABB 1. Multifunctional three-phase monitoring relays. CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet. Features. Approvals. Marks.

ABB 1. Multifunctional three-phase monitoring relays. CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet. Features. Approvals. Marks. 2CDC 251 054 F0t08 CM-MPN.52 2CDC 251 055 F0t08 CM-MPN.62 2CDC 251 056 F0t08 CM-MPN.72 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage

More information

Test Specification for Type Approval

Test Specification for Type Approval A2 (1991) (Rev.1 1993) (Rev.2 1997) (Rev. 2.1 July 1999) (Rev.3 May 2001) (Corr.1 July 2003) (Rev.4 May 2004) (Rev.5 Dec 2006) (Rev.6 Oct 2014) Test Specification for Type Approval.1 General This Test

More information

Part VI: Requirements for ISDN Terminal Equipment

Part VI: Requirements for ISDN Terminal Equipment Issue 9 November 2004 Spectrum Management and Telecommunications Policy Compliance Specification for Terminal Equipment, Terminal Systems, Network Protection Devices, Connection Arrangements and Hearing

More information

Testing for ground faults on storage batteries. Megger is a registered trademark

Testing for ground faults on storage batteries. Megger is a registered trademark WWW.MEGGER.COM Testing for ground faults on storage batteries Megger is a registered trademark Title Author Andrew Sagl Date January 2010 Keywords Abstract E-mail BGFT, circuit breaker uninterruptable

More information

KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES

KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate with up to 32 devices DESCRIPTION

More information

Section L5: PRE-ENERGIZATION TEST PROCEDURES FOR LOAD-ONLY ENTITIES AND TRANSMISSION-ONLY ENTITIES

Section L5: PRE-ENERGIZATION TEST PROCEDURES FOR LOAD-ONLY ENTITIES AND TRANSMISSION-ONLY ENTITIES Section L5: PRE-ENERGIZATION TEST PROCEDURES FOR LOAD-ONLY ENTITIES AND TRANSMISSION-ONLY ENTITIES PURPOSE The following is PG&E's procedure for pre-energization inspections. For PG&E to provide the Load

More information

TECHNICAL SPECIFICATION OF STAY WIRE FOR TRANSMISSION LINES AND SUB STATIONS

TECHNICAL SPECIFICATION OF STAY WIRE FOR TRANSMISSION LINES AND SUB STATIONS GUJARAT ENERGY TRANSMISSION CORPORATION LTD. Sardar Patel Vidyut Bhavan, Race Course, Vadodara: 390 007 TECHNICAL SPECIFICATION OF STAY WIRE FOR TRANSMISSION LINES AND SUB STATIONS GETCO/E/TS SWR019/R1

More information

MGVCL/MM/ /2082/11KV AB CABLE TECHNICAL SPECIFICATION FOR 11KV AERIAL BUNCHED CABLES FOR OVERHEAD LINES

MGVCL/MM/ /2082/11KV AB CABLE TECHNICAL SPECIFICATION FOR 11KV AERIAL BUNCHED CABLES FOR OVERHEAD LINES TECHNICAL SPECIFICATION FOR 11KV AERIAL BUNCHED CABLES FOR OVERHEAD LINES 1. Qualifying Requirement of AB Cable Manufacture/Supplier The manufacturer should have manufactured, successfully type tested

More information

TEST SUMMARY. Prüfbericht - Nr.: Test Report No.: Seite 2 von 25. Page 2 of 25

TEST SUMMARY. Prüfbericht - Nr.: Test Report No.: Seite 2 von 25. Page 2 of 25 15072259 001 Seite 2 von 25 Page 2 of 25 TEST SUMMARY 4.1.1 HARMONICS ON AC MAINS 4.1.2 VOLTAGE FLUCTUATIONS ON AC MAINS 4.1.3 MAINS TERMINAL CONTINUOUS DISTURBANCE VOLTAGE 4.1.4 DISCONTINUOUS INTERFERENCE

More information

Industrial IT for Utility Communications. Communicate IT Power Line Carrier ETL500

Industrial IT for Utility Communications. Communicate IT Power Line Carrier ETL500 Industrial IT for Utility Communications Communicate IT Power Line Carrier ETL500 Features Software programmable Power Line Carrier (PLC) unit for the transmission of speech, data and protection signals

More information

Model Number Structure

Model Number Structure Current Sensor CSM DS_E Solid-state, Plug-in Current Sensor Applicable to motor overcurrent protection and 3-phase AC current detection. Inverse-type, start-up lock type, and instantaneous type overcurrent

More information

KNX Powerline PL 110. KNX Association

KNX Powerline PL 110. KNX Association KNX Powerline PL 110 Table of Contents 1 Introduction...3 2 Standardisation...3 3 Transmission Process...4 3.1 Phase Coupling...5 3.2 Telegram Transmission...6 3.2.1 Training Sequence...6 3.2.2 Preamble

More information

SPTS 1 - Ratings and General Requirements for Plant, Equipment and Apparatus for The ScottishPower System and Connection Points to it.

SPTS 1 - Ratings and General Requirements for Plant, Equipment and Apparatus for The ScottishPower System and Connection Points to it. 1. SCOPE The requirements of this document apply to all Plant, Equipment and Apparatus that are part of, or are Directly connected to, the Company network. Requirements contained herein may be modified

More information

SRA 2250/6 RESISTOR ARS-01 RESISTOR AUTOMATICS

SRA 2250/6 RESISTOR ARS-01 RESISTOR AUTOMATICS ELECTRICAL ENGINEERING DIVISION Distribution Network Department SRA 2250/6 RESISTOR ARS-01 RESISTOR AUTOMATICS ELA T150.2 en SRA 2250/6 Resistor specification The SRA 2250/6 Resistor is intended to increase

More information

MANAGEMENT COMPLEX / GST:33AAACN1121C1ZG CIN:L93090TN1956GOI /TENDER ENQUIRY NO :ENQ/18-19/003497/MM15(02) /DATE

MANAGEMENT COMPLEX / GST:33AAACN1121C1ZG CIN:L93090TN1956GOI /TENDER ENQUIRY NO :ENQ/18-19/003497/MM15(02) /DATE NLC INDIA LIMITED (formerly Neyveli Lignite Corporation Limited) ('NAVARATNA'-Government of India Enterprise) MATERIALS MANAGEMENT COMPLEX Dr. Rajendra Prasad Road,Block-27,Neyveli-607807.Tamilnadu,India.

More information

High Performance Current Transducer IT 200-S ULTRASTAB = A. ε L

High Performance Current Transducer IT 200-S ULTRASTAB = A. ε L High Performance Current Transducer IT 200-S ULTRASTAB For the electronic measurement of currents: DC, AC, pulsed..., with galvanic isolation between the primary circuit and the secondary circuit. I PM

More information

ANNEXURE-I. Documents to be uploaded 1 Certificate of Registration with Industries 2 VAT Certificate 3 Service Tax Certificate

ANNEXURE-I. Documents to be uploaded 1 Certificate of Registration with Industries 2 VAT Certificate 3 Service Tax Certificate ANNEXURE-I Documents to be uploaded 1 Certificate of Registration with Industries 2 VAT Certificate 3 Service Tax Certificate 4 Excise Duty Registration Certificate 5 Pan Card 6 Approved Vendor Certificates

More information

Proximity Sensor Terminology

Proximity Sensor Terminology The following descriptions refer to the European standard EN 60947-5-2. of 2007. The specifications given here are intended to be minimum performance values described by the standard. Alignment must not

More information

Title: Southern States Type SLS Smart Sectionalizer Solid Dielectric Three Phase Sectionalizer. Product Specification Guide TABLE OF CONTENTS

Title: Southern States Type SLS Smart Sectionalizer Solid Dielectric Three Phase Sectionalizer. Product Specification Guide TABLE OF CONTENTS TABLE OF CONTENTS PAGE 1.0 SCOPE... 2 2.0 STANDARDS... 2 3.0 DESIGN REQUIREMENTS... 2 3.01 Service Conditions... 2 3.02 Ratings... 3 4.0 Sectionalizer Construction... 4 5.0 Mechanism... 6 6.0 Solid Dielectric

More information

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017 Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175, ART-B22-D300 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and

More information

SAUDI STANDARD NO. SASO IEC : 2007 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS

SAUDI STANDARD NO. SASO IEC : 2007 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS SAUDI STANDARD NO. SASO IEC 60669-2-2: 2007 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS Part 2-2: Particular requirements Electromagnetic remote-control switches (RCS) SAUDI ARABIAN

More information

ADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W

ADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W ADC5000 SERIES AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications 60W, 125W and 250 W Input voltage 230/115 VAC voltages 12, 24, 36 or 48 VDC Statistical MTBF >3 000

More information

Company Directive STANDARD TECHNIQUE: SD1E/2. Technical Requirements for Customer Export Limiting Schemes

Company Directive STANDARD TECHNIQUE: SD1E/2. Technical Requirements for Customer Export Limiting Schemes Company Directive STANDARD TECHNIQUE: SD1E/2 Technical Requirements for Customer Export Limiting Schemes Policy Summary This Standard Technique specifies the requirements for customer owned Export Limitation

More information

Measurement Procedure & Test Equipment Used

Measurement Procedure & Test Equipment Used Measurement Procedure & Test Equipment Used Except where otherwise stated, all measurements are made following the Electronic Industries Association (EIA) Minimum Standard for Portable/Personal Land Mobile

More information