ETSI EN V1.2.1 ( )

Size: px
Start display at page:

Download "ETSI EN V1.2.1 ( )"

Transcription

1 EN V1.2.1 (27-6) European Standard (Telecommunications series) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied

2 2 EN V1.2.1 (27-6) Reference REN/TM Keywords DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission 65 Route des Lucioles F-6921 Sophia Antipolis Cedex - FRANCE Tel.: Fax: Siret N NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (6) N 783/88 Important notice Individual copies of the present document can be downloaded from: The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on printers of the PDF version kept on a specific network drive within Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 27. All rights reserved. DECT TM, PLUGTESTS TM and UMTS TM are Trade Marks of registered for the benefit of its Members. TIPHON TM and the TIPHON logo are Trade Marks currently being registered by for the benefit of its Members. 3GPP TM is a Trade Mark of registered for the benefit of its Members and of the 3GPP Organizational Partners.

3 3 EN V1.2.1 (27-6) Contents Intellectual Property Rights...6 Foreword...6 Introduction Scope References Definitions, symbols and abbreviations Definitions Symbols Abbreviations General characteristics Frequency bands and channel arrangements Special compatibility requirements between systems Transmission capacity and spectral efficiency Main requirements Transmitter characteristics Transmitter power Transmitter power and frequency control Transmitter power control (ATPC and RTPC) Automatic Transmitter Power Control (ATPC) Remote Transmitter Power Control (RTPC) Remote Frequency Control (RFC) Transmitter output power tolerance Radio Frequency (RF) spectrum mask Discrete CW components exceeding the spectrum mask limit Discrete CW components at the symbol rate Other discrete CW components exceeding the spectrum mask limit Spurious emissions - external Radio frequency tolerance Receiver characteristics Spurious emissions-external System performance without diversity BER as a function of receiver signal level Interference sensitivity Co-channel "external" interference sensitivity Adjacent channel interference sensitivity CW spurious interference Complementary requirements Branching/feeder requirements Waveguide flanges (or other connectors) Return loss at equipment antenna port (C/C' reference point) Intermodulation products Transmitter characteristics Spurious emissions - internal Receiver characteristics Input level range Spurious emissions - internal Image rejection Innermost channel selectivity System performance without diversity Equipment Residual BER (RBER) Interference sensitivity for CCDP with XPIC operation Co-channel "internal" interference sensitivity in flat fading conditions...22

4 4 EN V1.2.1 (27-6) Co-channel "internal" interference sensitivity under dispersive fading conditions Distortion sensitivity System characteristics with diversity Differential delay compensation BER performance...23 Annex A (normative): Frequency bands from 1,4 GHz to 2,7 GHz...24 A. Introduction...24 Annex B (normative): Frequency bands from 3 GHz to 11 GHz (channel separation up to 3 MHz and 56 / 6 MHz)...25 B. Introduction...25 B.1 System B.1 ( Mbit/s; STM- - 2 STM- / 3 GHz to 11 GHz / 1,75 MHz to 29,65 MHz)...26 B.1.1 Distortion sensitivity...26 B.2 System B.2 (STM-1 / 3 GHz to 1,5 GHz / about 3 MHz ACAP)...26 B.2.1 Radio Frequency (RF) spectrum mask...26 B.2.2 Receiver innermost channel selectivity...29 B.3 System B.3 (2 STM-1 / 3 GHz to 1,5 GHz / about 3 MHz CCDP)...29 B.3.1 Radio Frequency (RF) spectrum mask...29 B.3.2 Innermost channel selectivity...31 B.3.3 Distortion sensitivity...32 B.4 System B.4 (4 STM- / 5 34 / 3 GHz to 1,5 GHz / about 3 MHz ACAP)...33 B.5 System B.5 (8 STM- / 1 34 / 3 GHz to 1,5 GHz / about 6 MHz ACAP)...33 B.6 System B.6 (2 STM1 (ACCP) or STM-4 / 4 STM1 (CCDP) / 3 GHz to 1,5 GHz / about 6 MHz)...33 Annex C (normative): Frequency bands from 3 GHz to 11 GHz (channel separation 4 MHz)...34 C. Introduction...34 C.1 System C.1 (2 STM-1 / 3 GHz to 11 GHz / 4 MHz - CCDP)...34 C.1.1 Radio Frequency (RF) spectrum mask...35 C.1.2 Distortion sensitivity...36 C.2 System C.2 (2 STM-1 / 3 GHz to 11 GHz / 4 MHz - ACAP)...36 C.2.1 Radio Frequency (RF) spectrum mask...36 C.2.2 Receiver input level range...37 C.3 System C.3 (4 STM-1 / 3 GHz to 11 GHz / 4 MHz - CCDP)...37 C.3.1 Transmitter Radio Frequency (RF) spectrum mask...37 C.3.2 Receiver input level range...38 C.3.3 Distortion sensitivity...38 Annex D (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz...39 D. Introduction...39 D.1 System D.1 (2 / 2 34 Mbit/s / 13 GHz, 15 GHz and 18 GHz / 1,75 MHz / 28 MHz)...4 D.1.1 Distortion sensitivity...4 D.2 System D.2 (sub STM- / 18 GHz / 3,5 MHz)...4 D.3 System D.3 (STM- / 13 GHz, 15 GHz and 18 GHz / 28 MHz ACCP-14 MHz ACAP)...41 D.4 System D.4 (STM- / 13 GHz, 15 GHz and 18 GHz / 14 MHz ACCP)...41 D.4.1 Distortion sensitivity...41 D.5 System D.5 (STM-1 / 13 GHz and 15 GHz / about 3 MHz ACAP)...41

5 5 EN V1.2.1 (27-6) D.6 System D.6 (2 STM-1 / 13 GHz and 15 GHz / about 3 MHz CCDP)...41 D.7 System D.7 (STM-1 / 18 GHz / 27,5 MHz and 55 MHz)...42 D.7.1 RF spectrum mask...42 D Class 4 equipment...42 D Class 5B equipment...43 D.7.2 Distortion sensitivity...43 D.8 System D.8 (2 STM-1 (ACCP) and STM-4 (CCDP) / 13 GHz, 15 GHz and 18 GHz / 55 MHz and 56 MHz)...43 D.9 System B.4 (4 STM- / 5 34 / 13 GHz, 15 GHz and 18 GHz / 27,5 MHz and 28 MHz ACAP)...43 D.1 System B.5 (8 STM- / 1 34 / 13 GHz, 15 GHz and 18 GHz / 55 MHz and 56 MHz ACAP)...44 Annex E (normative): Frequency bands from 23 GHz to 55 GHz...45 E. Introduction...45 E.1 Systems E.1, E.2 and E.3: Transmitter spectrum mask for class 5B equipment...46 Annex F (normative): Transmission of packet data and combinations of other signals in bands from 3 GHz to 55 GHz...47 F.1 Introduction...47 F.2 General characteristics...47 F.2.1 Frequency characteristics and channel arrangements...47 F.2.2 Transmission capacities and equipment assessment...47 Annex G (informative): Additional information...48 G.1 Residual Bit Error Ratio (RBER) and Frame Error Ratio (RFER)...48 G.2 Measurement test set for XPI characteristics...49 G.3 Differential delay compensation range...5 G.4 FER/BER equivalence and FER performance measurement equipment settings (example)...5 G.4.1 FER/BER equivalence...5 G.4.2 FER equipment settings and measurement techniques (example)...51 G.5 Automatic Transmitter Power Control (ATPC)...51 Annex H (informative): Mitigation techniques referred in ERC/DEC()7 (18 GHz band)...53 Annex I (informative): Bibliography...54 History...55

6 6 EN V1.2.1 (27-6) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to. The information pertaining to these essential IPRs, if any, is publicly available for members and non-members, and can be found in SR 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to in respect of standards", which is available from the Secretariat. Latest updates are available on the Web server ( Pursuant to the IPR Policy, no investigation, including IPR searches, has been carried out by. No guarantee can be given as to the existence of other IPRs not referenced in SR 314 (or the updates on the Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by Technical Committee Transmission and Multiplexing (TM). The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas, as identified below: Part 1: "Overview and system-independent common characteristics"; Part 2-1: "System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 2-2: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 3: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where simplified or no frequency co-ordination procedures are applied"; Part 4-1: "System-dependent requirements for antennas"; Part 4-2: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for antennas". National transposition dates Date of adoption of this EN: 15 June 27 Date of latest announcement of this EN (doa): 3 September 27 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 March 28 Date of withdrawal of any conflicting National Standard (dow): 31 March 28 Introduction The introduction of EN [15] applies.

7 7 EN V1.2.1 (27-6) 1 Scope The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in two different clauses sub-sets: Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] and further detailed in EN [16]. Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless they are considered having been commonly agreed for proper system operation and deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some of these requirements is made on a voluntary basis. Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are given in EN [16]. For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive "essential requirements" mentioned above, description and limits are detailed in the present document in the annexes A to G, subdivided by frequency band or specific applications. The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system requirements are covered in EN (see bibliography) and EN (see bibliography). The present document does not cover test procedures and test conditions which are set out in EN [14]. As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment classes are defined in EN [16]. The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format, provided that all the requirements in the relevant parts of this EN series are met. In some cases, where within the same spectral efficiency class there are different applications, (e.g. for multi-channel trunk or single channel operation), that justify different radio frequency parameters, two different equipment "types" (e.g. type 1 and 2) are provided. Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE Directive [1] for DFRS may be found in TR (see bibliography). Technical background for most of the parameters and requirements referred to in this EN series may be found in TR (see bibliography).

8 8 EN V1.2.1 (27-6) 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at NOTE: While any hyperlinks included in this clause were valid at the time of publication cannot guarantee their long term validity. [1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [2] CENELEC EN 12215: "Sectional Specification: Radio frequency coaxial connectors - Series EIA flange". [3] CEPT/ERC/DEC()7: "ERC Decision of 19 October 2 on the shared use of the band GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-earth)". [4] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-: Classification of environmental conditions; Introduction". [5] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-1: Classification of environmental conditions; Storage". [6] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-2: Classification of environmental conditions; Transportation". [7] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations". [8] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations". [9] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-: Specification of environmental tests; Introduction". [1] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-1: Specification of environmental tests; Storage". [11] EN : "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-2: Specification of environmental tests; Transportation". [12] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of environmental tests; Stationary use at weatherprotected locations".

9 9 EN V1.2.1 (27-6) [13] EN : "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected locations". [14] EN : "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point equipment - Definitions, general requirements and test procedures". [15] EN : "Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview and system-independent common characteristics". [16] EN : "Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for digital systems operating in frequency bands where frequency coordination is applied". [17] IEC : "Hollow metallic waveguides. Part 2: Relevant specifications for ordinary rectangular waveguides". [18] IEC : "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary rectangular waveguides". [19] IEC : "Radio-frequency connectors. Part 1: General requirements and measuring methods". [2] IEC 6339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange connectors". [21] IEC : "Methods of measurement for equipment used in digital microwave radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 4: Transmitter/receiver including modulator/demodulator". [22] IEC : "Methods of measurement for equipment used in digital microwave radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 8: Adaptive equalizer". [23] IEEE : "IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications". [24] IEEE : "IEEE Conformance Test Methodology for IEEE Standards for Local and Metropolitan Area Networks - Specific Requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications". [25] ITU-T Recommendation G.78: "Sub STM- network node interface for the synchronous digital hierarchy (SDH)". [26] ITU-T Recommendation O.151: "Error performance measuring equipment operating at the primary rate and above". [27] ITU-T Recommendation O.181: "Equipment to assess error performance on STM-N interfaces". [28] ITU-T Recommendation O.191: "Equipment to measure the cell transfer performance of ATM connections". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN [15] apply.

10 1 EN V1.2.1 (27-6) 3.2 Symbols For the purposes of the present document, the symbols given in EN [15] apply. 3.3 Abbreviations For the purposes of the present document, the abbreviations given in EN [15] apply. 4 General characteristics For commonality of purpose, systems are sub-divided into families by frequency range of operation; one normative annex is assigned to each family of equipment. There are six families of annexes, referenced from A to F, which may be found in both in the present document and EN [16]: A Frequency bands from 1,4 GHz to 2,7 GHz. B Frequency bands from 3 GHz to 11 GHz (Channel separation up to 3 MHz and 56/6 MHz). C Frequency bands from 3 GHz to 11 GHz (Channel separation 4 MHz). D Frequency bands 13 GHz, 15 GHz and 18 GHz. E Frequency bands from 23 GHz to 55 GHz. F Transmission of packet data and combinations of other signals in bands from 3 GHz to 55 GHz. 4.1 Frequency bands and channel arrangements Frequency bands and channel arrangements, which are relevant for equipment covered by the present document, are defined by ITU-R Recommendations and/or CEPT Recommendations and are referenced in the first table of each annex A through E (i.e. tables A.1 through E.1) of EN [16]. ITU-R Recommendations or CEPT/ECC (see note) recommended frequency channel arrangements, known at the date of publication of this EN series, are set out for reference only. In general, the channel arrangement is relevant neither to article 3.2 of the R&TTE Directive [1] nor for other requirements in the present document; only the frequency band, actual channel separation and, in some cases innermost channels separation are relevant for defining the set of parameters and test suites relevant to each system. NOTE: CEPT Recommendations were published until 22 as CEPT/ERC Recommendations; consequently to the restructuring of ERC under new ECC organization, new and revised Recommendations might formally change their reference as ECC Recommendations, without changing their technical content and applicability. Other national or future ITU-R Recommendations or CEPT/ECC Recommendations, set around the same or close to the frequency range of present ITU-R Recommendations or CEPT/ECC Recommendations, are considered applicable to systems assessed against this EN series, provided that they use the same channel separation. Specification and tests of wide radio-frequency band covering units and multirate equipment are placed in normative annex G of EN [16]. Whenever applicable, it is also valid for assessing parameters specified in the present document. 4.2 Special compatibility requirements between systems There shall be no requirement to operate transmitting equipment from one supplier with receiving equipment from another and, depending on the deployment conditions, it shall be possible to operate the system in vertical and/or horizontal polarization, if required by the channel arrangement.

11 11 EN V1.2.1 (27-6) To be compatible with certain constraints given by existing installations and/or deployments already made with systems from other supplier or for different FS applications, new systems on the same path may be subject to additional requirements, other than those derived for a single supplier or same application environment. NOTE: This does not imply that when a single supplier is involved there are no similar requirements; however, they do not need standardization because many other technical and cost-effective solutions might be flexibly adopted under suppliers' own responsibility only. For the purposes of this EN series the following set of compatibility requirements between systems has been defined: a) There may be a requirement to multiplex different suppliers' equipment on the same polarization of the same antenna. This will not apply to systems with an integral antenna. b) There may be a requirement to multiplex different suppliers' equipment on different polarizations of the same antenna. This will not apply to systems with an integral antenna. c) There may be a requirement to coexist with analogue systems on adjacent cross-polarized channels on the same route. 4.3 Transmission capacity and spectral efficiency The payload bit rates considered in this EN series are commonly tailored to typical PDH and SDH baseband interfaces: 2,48 Mbit/s, 2 2,48 Mbit/s, 8,448 Mbit/s, 2 8,448 Mbit/s, 34,368 Mbit/s, 2 34,368 Mbit/s, 51,84 Mbit/s (STM-), 2 51,84 Mbit/s (2 STM-), 155,52 Mbit/s (STM-1), N 155,52 Mbit/s (N STM-1), STM-N. Only systems in annex A, due to the smaller channel separation provided, are (exceptionally) labelled with typical capacity rate without specific reference to PDH/SDH rates. In the following text these capacities will be simply referred to as 2 Mbit/s, 2 2 Mbit/s, 8 Mbit/s, 2 8 Mbit/s, 34 Mbit/s, 2 34 Mbit/s, STM-, 2 STM-, STM-1, N STM-1 and STM-N. For each system the bit rates related to each class and their relevant channel separation are detailed in the second table of each annex A through E (i.e. tables A.2 through E.2) of EN [16] of this EN series. Provided that they meet all requirements of the relevant annex, equivalent PDH or SDH transport rates may be used where appropriate. Such equivalent transport rates may be: N 2 Mbit/s or other PDH rates in place of equivalent higher PDH rates. 14 Mbit/s (including 4 34 Mbit/s) in place of STM-1. Any PDH mapping into STM- or STM-1 frames, as defined in the basic multiplexing schemes. N 2 Mbit/s mapped into SDH VC12 or VC2 transport bit rates (sub-stm- defined, as sstm-1k or sstm-2n capacities, by ITU-T Recommendation G.78 [25]) in place of a PDH rate (e.g. 4 VC12/sSTM14 or 1 VC2/sSTM21 in place of 8 Mbit/s). NOTE: In addition to this general principle, annex D (system D.2) presents specific characteristics for sub-stm- systems in the 18 GHz band. Any other signal (e.g. IP frames or ATM cells, even possibly mixed with PDH capacities) mapping into PDH or SDH frames, according present or future basic ITU-T or multiplexing schemes. The present document is also applicable to other base band interfaces (e.g. packet data interfaces or mixed interfaces) even if multiplexed (including compression algorithms if any) into proprietary frames; for such cases annex F gives the basic rules for applying the conventional PDH/SDH set of parameters to those equipment assessment.

12 12 EN V1.2.1 (27-6) 5 Main requirements This clause summarizes requirements related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] that are further detailed in EN [16]. However, for some requirements, besides the relevant essential limits set out in EN [16] for the purpose of their separate publishing in the Official Journal of the European Communities (OJEC) under the R&TTE Directive [1], additional, non-essential, more stringent limits are here set out in response to specific compatibility requirements by network operators when deploying new systems on the same routes with existing systems from other suppliers. The specified transmitter and receiver characteristics shall be met with the appropriate baseband signals applied at reference point X' and received from reference point X of figure 1 of EN [15]. Table 1: Baseband test signals Type of baseband signal interface at X/X' Test signal to be applied according to PDH PRBS ITU-T Recommendation O.151 [26] SDH ITU-T Recommendation O.181 [27] ATM ITU-T Recommendation O.191 [28] Ethernet interface (packet data) IEEE 82.3 [23], IEEE [24] Other than the above Relevant standards which the interface refers to 5.1 Transmitter characteristics Transmitter power The only essential requirement is the Maximum Output Power which is an essential requirement under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. For guidance, in addition to the absolute maximum transmitter power, typical values of transmitter highest power for real equipment, of feeder loss and length, and of antenna diameter and gain are provided in TR (see bibliography) in order to support inter- and intra- compatibility and sharing analysis. In some frequency bands, or parts of frequency bands, ITU-R Recommendations define specific limits in terms of output power and/or EIRP (or output power and/or EIRP density) in order to improve the compatibility with other Radio Services sharing these frequency bands with the FS. An additional capability for output power level adjustment may be required, for regulatory purposes, in the interface regulations according to article 4.1 of the R&TTE Directive [1], in which case the range of adjustment, either by fixed or automatic attenuators, should be in increments of 5 db or less. In particular, for the band 18 GHz, the FS shall, where practical, implement the appropriate mitigation techniques as required in ERC/DEC()7 [3]. See informative annex H Transmitter power and frequency control Transmitter power control (ATPC and RTPC) Automatic Transmitter Power Control (ATPC) This functionality is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. Besides those essential requirements specified in EN [16], ATPC may be requested as mandatory functionality in the licensing conditions for the following purposes: to enhance network density (see note 1); as a mitigation factor for sharing with other Services due to CEPT Decisions (see notes 2 and 3).

13 13 EN V1.2.1 (27-6) Administrations should explicitly state whether ATPC is used as a regulatory measure for either frequency coordination or as a mitigation technique to protect other services in its radio regulation interface for notification according to article 4.1 of the R&TTE Directive [1]. NOTE 1: In this particular case, as an additional, but non-essential to article 3.2, requirement, it may be specified that transmitter output power meet the spectrum mask limits set out in clause 4.2 of EN [16] throughout the ATPC range. NOTE 2: The first example is in the 18 GHz band, where since there is sharing between FS and FSS, ATPC will become a mandatory feature for all new equipment to be deployed after the date referred by ERC/DEC()7 [3], however, the actual usage of ATPC will be required only where practical and depending on local sharing conditions with satellite services and local deployment conditions in existing networks. The ATPC range is not subject to standardization. NOTE 3: When used as mitigation factor ATPC should not be, in principle, used to enhance network density Remote Transmitter Power Control (RTPC) This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Remote Frequency Control (RFC) This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Transmitter output power tolerance The only essential requirement is the power tolerance around the nominal output power together with the associated temperature range, declared by the supplier, which is considered essential under article 3.2 of R&TTE Directive [1]. For relevant limits see EN [16]. An additional voluntary requirement may be required where more stringent limits apply according to the specific environmental condition for which the equipment is designed. In this case, when specified, the tolerance of the nominal output power shall be within the limits specified for: Systems operating within classes of weather protected locations defined in EN [4] to EN [13]; nominal output power, when specified, within ±A db; the value for A is system dependent and is given in the relevant annex(es). Systems operating within non-weather protected locations classes 4.1 and 4.1E and within classes 3.3, 3.4 and 3.5 weather protected locations defined in EN [4] to EN [8]; nominal output power within ±B db; the value for B is system dependent and is given in the relevant annex(es). In any case, the less stringent tolerance (±B db or the only one when a single tolerance exists), when applied to the operational environmental profile declared by the supplier (i.e. not necessarily an standardized one), is considered essential to article 3.2 and contained in EN [16]. Only voluntary and more stringent tolerances are specified in the present document Radio Frequency (RF) spectrum mask The radio frequency spectrum density mask is relevant to essential requirements under article 3.2 of R&TTE Directive [1], the limits for the essential portion of RF spectrum density masks are found in EN [16]. Additional non-essential requirements for spectrum density masks may have to be met in cases where there is a requirement for internal system dependent reasons only. Where more stringent RF spectrum masks are required, they may be found in the relevant annex(es) of the present document.

14 14 EN V1.2.1 (27-6) The db level shown on the spectrum masks relates to the spectral power density at the carrier centre frequency, disregarding the residual of the carrier (due to modulation imperfection). NOTE: The masks do not include frequency tolerance. Systems specified in annex A are an exception to this general rule; in this case "fo" identifies the nominal carrier frequency and the spectrum mask includes an allowance for frequency tolerance. The spectrum analyser settings for measuring the RF spectrum mask are shown in table 6 of clause of EN [16]. They are reproduced in table 2 in the present document for the reader's convenience. Table 2: Spectrum analyser settings for RF power spectrum measurement Channel separation (CS) (MHz),3 < CS,3,3 < CS,3,3 < CS,9,9 < CS < CS < CS Centre fo fo fo fo fo fo frequency Sweep width > 5 CS > 5 CS > 5 CS > 5 CS > 5 CS > 5 CS (MHz) Scan time auto auto auto auto auto Auto IF bandwidth (khz) Video bandwidth (khz),3,1,1,3,3,3 NOTE: The masks do not include frequency tolerance. Systems specified in annex A are an exception to this general rule; in this case "fo" identifies the nominal carrier frequency and the spectrum mask includes an allowance for frequency tolerance Discrete CW components exceeding the spectrum mask limit Discrete CW components at the symbol rate This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. NOTE: In some previous ENs more stringent limits were required, due to the possibility of interference on the analogue baseband channels of analogue systems deployed on the same route with digital systems. However these deployments are no longer practical and such requirements are therefore no longer considered appropriate (for new equipment) Other discrete CW components exceeding the spectrum mask limit This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Spurious emissions - external "External" limit for spurious emissions from transmitters are necessary in order to limit interference into other systems operating wholly externally to the system under consideration (external emissions). This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Radio frequency tolerance This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16].

15 15 EN V1.2.1 (27-6) In some cases, as an additional voluntary requirement, more stringent limits apply according to the specific environmental condition for which the equipment is designed. In this case, when specified, maximum radio frequency tolerance shall not exceed: ±Y ppm or ±YY khz, whichever is the more stringent, for operation in weather protected environmental classes 3.1 and 3.2 defined in EN [7]; ±X ppm or ±XX khz, whichever is the more stringent, for operation in other more severe environmental classes defined in EN [4] to EN [8]. The values of either X or XX and either Y or YY are system dependent and are given in the relevant annex(es). In any case, the less stringent tolerance (±X ppm or ±XX khz, the only one when a single tolerance exists), when applied to the operational environmental profile declared by the supplier (i.e. not necessarily an standardized one), is considered to be essential with respect to article 3.2 of R&TTE Directive [1] and is specified in EN [16]. Only voluntary and more stringent tolerances are specified in the present document. These limits include both short-term factors (environmental effects) and long-term factors (ageing effects). The supplier shall specify the guaranteed short-term part and the expected ageing part. 5.2 Receiver characteristics Spurious emissions-external This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. 5.3 System performance without diversity BER as a function of receiver signal level This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Interference sensitivity Co-channel "external" interference sensitivity "External" co-channel interference is considered to be that interference from a system fully independent from the one under test (i.e. a system deployed by another operator in the same geographical area). This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16] Adjacent channel interference sensitivity This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. In addition, for ACCP/CCDP applications of class 4 and class 5B systems in frequency bands below 15 GHz with CS 14 MHz, to cope with differential fading effects on the longer hops in systems operating on adjacent channels on the same route but using different antennas, C/I values up to about 1 db tighter than those reported in EN [16] may be necessary. However, this actually depends on the hop fading occurrence factor and the ATPC range implemented on all adjacent systems (i.e. the higher is the ATPC common range, the lower is the C/I sensitivity need). The relationship of these parameters on hop performance prediction is not identified; therefore specific requirement cannot be defined.

16 16 EN V1.2.1 (27-6) CW spurious interference This parameter is relevant to essential requirements under article 3.2 of R&TTE Directive [1] and is specified in EN [16]. 6 Complementary requirements This clause considers requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless, all or some of these requirements are considered useful for proper system operation and deployment when specific deployment conditions or compatibility requirements, as defined in clause 4.2, are present. Compliance to all or some of these requirements is on a voluntary basis. 6.1 Branching/feeder requirements Waveguide flanges (or other connectors) When flanges (or coaxial types) are required at reference point(s) B, B', C, C', the following types shall be used: UBR/PBR/CBR-XXX flanges according to IEC [18] shall be used for the bands specified in table 3. When the same band appears covered by two different options, both are admitted, provided that adaptors are available. Coaxial connectors can be used, as an option, for all frequency bands (see note). The impedance of the coaxial ports shall be nominally 5 Ω. NOTE: For coaxial connectors a number of popular standards exist; attention is drawn to a range of coaxial connectors referred to in parts 1 and 2 of IEC 6339 [2], IEC [19], CENELEC EN [2]. However, it should be noted that these standards are not exhaustive. Table 3: Waveguide flanges of UBR/PBR/CBR types (according to IEC [18]) Frequency band(s) WG "R" designation (and its frequency range in GHz) according to IEC [17] 1,4 GHz and 2,5 GHz bands 2,1 GHz to 2,5 GHz band None (Only coaxial connections are commonly used) 3,5 GHz band Either R 32 (2,6 to 3,95) or R 4 (3,3 to 4,9) 4 GHz band R 4 (3,3 to 4,9) 5 GHz band R 48 (3,95 to 5,85) L6/U6 GHz band R 7 (5,85 to 8,2) 7 GHz band(s) Either R 7 (5,85 to 8,2) or R 84 (7,5 to 1) 8 GHz band R 84 (7,5 to 1) 1,5 GHz band 11 GHz band Either R 1 (8,2 to 12,4) or R 12 (1 to 15) 13 GHz band Either R 12 (1 to 15) or R 14 (12,4 to 18) 15 GHz band R 14 (12,4 to 18) 18 GHz band either R 18 (15 to 22) or R 22 (18 to 26) 23 GHz band R 22 (18 to 26) 26 GHz band Either R 22 (18 to 26) or R 26 (22 to 33) 28 GHz band Either R 26 (22 to 33) or R 32 (26,5 to 4) 31 GHz and 32 GHz bands R 32 (26,5 to 4) 38 GHz band R 32 (26,5 to 4) 48,5 GHz to 5,2 GHz band R 5 (4 to 6) 52 GHz band Either R 5 (4 to 6) Or R 62 (5 to75) 55 GHz band Either R 5 (4 to 6) Or R 62 (5 to 75)

17 17 EN V1.2.1 (27-6) Return loss at equipment antenna port (C/C' reference point) It is frequent practice that equipment without integral antennas are connected to feeder/antenna systems from other supplier. For equipment according to the present document, that uses outdoor radio frequency units, which are likely to have integral antennas or similar technical solutions, without long feeder connections, the impact of return loss at the antenna port on system performance is negligible and does not require (see also note to table 4) standardized limits. For fully indoor systems, which are generally deployed with longer feeder connections to an external antenna, and may be required to operate with respect to compatibility requirements specified in clause 4.2 list items a and b, the minimum return loss depends on the signal bandwidth and modulation complexity. The required values, at point C and C' of figure 1 of EN [15], over the required RF channels and measured back in the direction to the equipment shall meet the values specified in table 4. Table 4: Return loss at the C and C' port towards equipment for fully indoor system Channel separation (CS) Spectral efficiency class (MHz) 1 and 2 3 and 4 5 and 6 CS 27,5 14 db 18 db 2 db (64 QAM based) 22 db (128 QAM based) 24 db (256 QAM based) 26 db (512 QAM based) 27,5 > CS 13,75 Not required 12 db 16 db 13,75 > CS 7 Not required Not required 1 db 7 > CS Not required Not required Not required NOTE: Not required means that return loss is not an issue for performance but only for potential power loss due to reflection. Even if there might be special cases where RF units designed for outdoor operation are also used in fully indoor conditions, this should be resolved on a case by case basis. For feeder/antenna return loss requirements see EN (see bibliography). 6.2 Intermodulation products Where multi-channel branching system is concerned and where the system is intended to comply with compatibility requirement in clause 4.2, each odd order intermodulation product, caused by different transmitters linked to the same branching system, shall be less than -11 dbm referenced to reference point B of figure 1 of EN [15] of this EN series with an output power per transmitter limited to the maximum power stated by the supplier for the equipment. The reference power shall be the maximum power stated by the supplier for the equipment. This clause is not intended for use with conformance tests, but only, if required, for type tests agreed between user and supplier. The measurement, if any, will be carried out with un-modulated signals of the same power of the average level of the digital signals. 6.3 Transmitter characteristics Spurious emissions - internal This category covers emissions that, for system compatibility with other systems only, may be required to be more stringent than the "external" emissions detailed in clause Requirements for internal spurious emissions are necessary only for systems that are required to comply with compatibility requirements under clause 4.2 list items a, b and c. The levels of the spurious emissions from the transmitter, referenced to reference point B' of figure 1 of EN [15] are specified in table 5. The level of spurious emission will be the total average level integrated over the bandwidth of the channel under consideration.

18 18 EN V1.2.1 (27-6) Table 5: Internal levels for the transmitter spurious emissions Controlling factor for requirement application Within transmit half band, digital interference to analogue systems on the same route, for digital systems with compatibility requirements as in clause 4.2 list item c. Within receive half band, digital into digital interference on the same local multi-channel branching/antenna system, for digital systems with compatibility requirements as specified in clause list item a. Within receive half band, digital into digital interference for digital systems without branching network (i.e. single transceivers with duplexer), for digital systems with compatibility requirements as specified in clause 4.2 list item b. Spurious emission frequency relative to channel assigned frequency Discrete (CW) spurious emissions within the same transmit half band All spurious signals within The receive half band Specification limit -6 dbm -9 dbm -7 dbm 6.4 Receiver characteristics Input level range The input Receiver Signal Level (RSL) range, under flat fading condition, where the BER is kept lower than a specified level (typically 1-6 for availability purpose and, for higher modulation formats, 1-1 for errored seconds performance) depends on various parameters such as, but not limited to, frequency band, hop length and spectrum efficiency class. In principle, the highest is the range, the more flexible is the use of the equipment; however, high capacity systems with complex modulations (e.g. classes 5 and 6) suffer from one side of relatively higher RSL/BER thresholds and from the other side from more sensitivity to non-linear distortion caused by RX chain saturations. A unique standardized approach is not therefore advisable, nevertheless the necessary fade-margin shall be accommodated; the following "design objectives" are given for guidance only. The lower limit for the RSL threshold for a Bit Error Ratio (BER) 1-6 is specified in the relevant annex of EN [16]. The upper limit for the RSL, where the same BER of 1-6, due to non-linear distortions, is not exceeded is assumed to be XX db above. In the same fashion, the upper limit for the RSL where a lower BER of 1 -y (typically 1-8 or 1-1 ) is not exceeded is assumed to be YY db above the relevant RSL threshold for that BER also specified in the relevant annex of EN [16]. Indicative values for XX db and YY db are given in table 6.

19 19 EN V1.2.1 (27-6) Frequency Range 1,5 GHz to 3 GHz 3 GHz to 11 GHz 13 GHz to 18 GHz 23 GHz to 38 GHz 4 GHz to 55 GHz Table 6: Indicative design objectives for input level range XX RSL range (db) for : YY RSL range (db) for : BER 1-6 BER 1-8 BER 1-1 Spectral efficiency class Spectral efficiency class Spectral efficiency class 1 to to to (see note 1) 5 (see note 1) 44 (see note 3) 44 (see 47 (see note 2) 47 (see note 2) 44 (see note 3) Systems C.x: See annex C Other systems: 44 (see note 3) 44 (see note 3) 41 (see note 3) (see note 4) 41 (see 34 (see note 5) 41 (see note 4) (see note 4) 38/41 (see note 7) 38/41 (see notes 6 and 7) Systems C.x: See annex C Other systems: note 3) note 4) NOTE 1: RSL higher than -2 dbm is not required. NOTE 2: RSL higher than -22 dbm is not required. NOTE 3: RSL higher than -23 dbm is not required. NOTE 4: RSL higher than -24 dbm is not required. NOTE 5: For channel spacing > 28 MHz only. NOTE 6: For channel spacing 28 MHz only. NOTE 7: Higher value for systems with compatibility requirements under clause 4.2. NOTE 8: In case of two-carriers systems (D.8 and E.4 systems referred in annexes D and E, respectively), when carrying STM-4 or when carrying 4 STM-1, with each STM-1 mixed on both carriers, the test shall be made changing the RSL of both carrier simultaneously. For more details see clause G.3 in EN [16]. These limits apply without interference and are referenced to point B (points B and C may coincide when simple duplexer is used) of figure 1 of EN [15]. For equipment designed to operate only with ATPC as a fixed permanent feature the above maximum input levels are reduced by an amount up to the ATPC range Spurious emissions - internal For systems without the compatibility requirements of clause 4.2 there is no requirement. When equipment is required to share the same antenna with other equipment, the spurious emissions limits, referenced to point B, are specified in table 7. The required level will be the total average level integrated over the bandwidth of the channel under consideration. Table 7: Limits of spurious emissions-internal Controlling factor Spurious falling in the same receive half-band for systems with compatibility requirements of clause 4.2 list item a. Spurious falling in the same receive half-band for systems with compatibility requirements of clause 4.2 list item b. Specification limit -11 dbm -7 dbm NOTE: In addition, when compatibility with FDM systems on the same branching/antenna system is required, more stringent limits for CW lines (e.g. L.O. residual emission) might be necessary, ranging from -85 dbm to -125 dbm, according to the actual interfered baseband frequency of the analogue system and the possible additional decoupling due to local IPI of the antenna (conventionally assumed to be 4 db).

20 2 EN V1.2.1 (27-6) Image rejection The receiver image(s) rejection shall be as listed in table 8. Table 8: Receiver image rejection Controlling factor a) For any image frequency falling within the receive half band while using branching on different polarizations as defined under the compatibility requirements in clause 4.2 list item b. b) For systems not intended to fulfil any compatibility requirements in clause 4.2 list item a and/or 4.2 list item b. c) For any image frequency falling within the receive half band while using branching on same polarization, as defined in clause 4.2 list item a, or in the transmit half band on different polarization, as defined by the compatibility requirements in clause 4.2 list item b. d) For any image(s) frequency falling within transmit half band and using branching on same polarization, as defined by the compatibility requirements in clause 4.2 list item a. Image rejection 9 db Not Applicable 1 db 12 db Additional requirements, if any, may be found in the relevant annexes A through to E of the present document Innermost channel selectivity For systems, which are intended to comply with compatibility requirement under clause 4.2 list items a and b, to guarantee innermost TX/RX channel compatibility, the inner side of the innermost receiver shall be within the mask which is system and channel arrangement dependent and given in annex(es) to the present document. Since it is not considered feasible to make a practical measurement of this characteristic, the supplier shall give the design data of all filters implemented on this receiver. 6.5 System performance without diversity Equipment Residual BER (RBER) The RBER level under simulated operating conditions without interference shall be guaranteed with a signal level at reference point B (or C) of the system block diagram of figure 1 of EN [15], which is between 1 db and 35 db above the threshold level which gives BER 1-6 (as specified in clause 5.3.1); however an upper limit above -3 dbm is not required (see note 1). NOTE 1: Only for the 52 GHz and 55 GHz bands the value could be relaxed to -32 dbm. The requirement is intended between base-band ports at reference points X' and X shown in figure 1 of EN [15]. As the measurement is made on the tributaries, the clause relative to one rate is also applicable to systems for n the same rate (e.g. requirement for 2 Mbit/s is applicable to n 2 Mbit/s). To guarantee a higher degree of service, see clause G.1, the network operator may require equipment to meet a RBER limit with the first adjacent channel interferer. In this case the RBER level under simulated operating conditions shall still be guaranteed with a signal level as specified above with an adjacent interference level set to represent a Carrier to Interference ratio (C/I) of: -4 db for all system classes 1 to db for class 5A systems (this figure assumes a minimum cross polar discrimination of 1 db for these systems). -3 db or -4 db for class 5B systems (see note 2). According to the supplier's declaration for class 6 systems.

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 217-2-1 V2.1.1 (2014-12) EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-1: System-dependent requirements for digital systems

More information

DraftETSI EN V1.2.1 ( )

DraftETSI EN V1.2.1 ( ) Draft EN 301 213-2 V1.2.1 (2000-04) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 300 113-2 V1.2.1 (2002-04) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended

More information

Final draft ETSI EN V1.1.1 ( )

Final draft ETSI EN V1.1.1 ( ) Final draft EN 301 460-3 V1.1.1 (2000-08) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-multipoint equipment; Part 3: Point-to-multipoint digital radio systems below 1 GHz

More information

Draft ETSI EN V1.3.1 ( )

Draft ETSI EN V1.3.1 ( ) Draft EN 300 430 V1.3.1 (2000-10) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of STM-1 digital signals

More information

ETSI EN V1.3.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.3.1 ( ) Harmonized European Standard (Telecommunications series) EN 302 217-2-2 V1.3.1 (2009-04) Harmonized European Standard (Telecommunications series) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Digital

More information

ETSI EN V1.2.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.2.1 ( ) Harmonized European Standard (Telecommunications series) EN 300 086-2 V1.2.1 (2008-09) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal

More information

Final draft ETSI EN V1.1.1 ( )

Final draft ETSI EN V1.1.1 ( ) Final draft EN 302 291-2 V1.1.1 (2005-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Close

More information

ETSI EN V7.0.1 ( )

ETSI EN V7.0.1 ( ) Candidate Harmonized European Standard (Telecommunications series) Harmonized EN for Global System for Mobile communications (GSM); Base Station and Repeater equipment covering essential requirements under

More information

Draft ETSI EN V1.3.1 ( )

Draft ETSI EN V1.3.1 ( ) Draft EN 300 431 V1.3.1 (2000-10) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio system for the transmission of digital signals operating

More information

ETSI EN V1.1.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.1.1 ( ) Harmonized European Standard (Telecommunications series) EN 302 617-2 V1.1.1 (2010-10) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and

More information

ETSI EN V2.1.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V2.1.1 ( ) Harmonized European Standard (Telecommunications series) EN 302 500-2 V2.1.1 (2010-10) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra WideBand (UWB)

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector

More information

ETSI EN V1.4.1 ( )

ETSI EN V1.4.1 ( ) EN 300 296-2 V1.4.1 (2013-08) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 387 V1.1.1 (1999-11) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Plesiochronous Digital Hierarchy (PDH); Low and medium capacity digital radio systems

More information

ETSI EN V1.4.1 ( )

ETSI EN V1.4.1 ( ) EN 301 213-3 V1.4.1 (2002-02) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range

More information

Draft ETSI EN V1.3.1 ( )

Draft ETSI EN V1.3.1 ( ) Draft EN 300 234 V1.3.1 (2000-10) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digital radio systems carrying 1 x STM-1 signals and operating

More information

Final draft EN V1.1.1 ( )

Final draft EN V1.1.1 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Plesiochronous Digital Hierarchy (PDH); Low and medium capacity DRRS operating in the

More information

Final draft ETSI EN V1.1.1 ( )

Final draft ETSI EN V1.1.1 ( ) Final draft EN 302 062 V1.1.1 (2002-10) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digital radio relay systems carrying STM-4, 4 STM-1 or

More information

Draft ETSI EN V2.2.0 ( )

Draft ETSI EN V2.2.0 ( ) Draft EN 302 217-2-2 V2.2.0 (2013-11) Harmonized European Standard Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Digital systems operating in

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 219-2 V1.1.1 (2001-03) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment transmitting

More information

ETSI EN V1.3.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.3.1 ( ) Harmonized European Standard (Telecommunications series) EN 302 435-2 V1.3.1 (2009-12) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Technical characteristics

More information

Draft ETSI EN V1.3.1 ( )

Draft ETSI EN V1.3.1 ( ) Draft EN 300 198 V1.3.1 (1999-11) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of digital signals operating

More information

ETSI EN V1.6.1 ( )

ETSI EN V1.6.1 ( ) EN 300 197 V1.6.1 (2002-03) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of digital signals operating at

More information

ETSI EN V1.5.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.5.1 ( ) Harmonized European Standard (Telecommunications series) EN 300 330-2 V1.5.1 (2010-02) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 471-2 V1.1.1 (2001-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Rules for Access and

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 301 489-2 V1.3.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V1.1.2 ( ) Harmonized European Standard

ETSI EN V1.1.2 ( ) Harmonized European Standard EN 302 729-2 V1.1.2 (2011-05) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Level Probing Radar (LPR) equipment operating in the

More information

ETSI EN V1.2.3 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.2.3 ( ) Harmonized European Standard (Telecommunications series) EN 301 166-2 V1.2.3 (2009-11) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment for analogue

More information

ETSI ES V1.1.1 ( )

ETSI ES V1.1.1 ( ) Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless digital video links operating above 1,3 GHz; Specification of typical receiver performance parameters for spectrum planning

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 390-2 V1.1.1 (2000-09) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-19 V1.2.1 (2002-11) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

Final draft ETSI EN V1.1.1 ( )

Final draft ETSI EN V1.1.1 ( ) Final draft EN 301 215-4 V1.1.1 (2003-07) European Standard (Telecommunications series) Fixed Radio Systems; Point to Multipoint Antennas; Antennas for multipoint fixed radio systems in the 11 GHz to 60

More information

ETSI EN V1.3.2 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.3.2 ( ) Harmonized European Standard (Telecommunications series) EN 302 288-2 V1.3.2 (2009-01) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices; Road Transport and Traffic Telematics

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 119-4 V2.1.1 (2004-09) European Standard (Telecommunications series) Environmental Engineering (EE); European telecommunication standard for equipment practice; Part 4: Engineering requirements

More information

Final draft ETSI EN V1.3.1 ( )

Final draft ETSI EN V1.3.1 ( ) Final draft EN 300 433-2 V1.3.1 (2011-05) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Citizens' Band (CB) radio equipment; Part 2: Harmonized EN covering

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 357-2 V1.1.1 (2000-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Analogue cordless wideband audio devices

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 718-2 V1.1.1 (2001-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Avalanche Beacons; Transmitter-receiver

More information

ETSI EN V1.5.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.5.1 ( ) Harmonized European Standard (Telecommunications series) EN 32 217-4-2 V1.5.1 (21-1) Harmonized European Standard (Telecommunications series) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4-2: Antennas;

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 330-2 V1.1.1 (2001-06) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 301 127 V1.3.1 (2002-07) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digital radio systems carrying SDH signals (up to 2 x STM-1) in frequency

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 302 858-2 V1.3.1 (2013-11) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Road Transport and Traffic Telematics (RTTT); Automotive radar equipment operating

More information

ETSI EN V1.2.1 ( ) Harmonized European Standard

ETSI EN V1.2.1 ( ) Harmonized European Standard EN 302 372-2 V1.2.1 (2011-02) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Equipment for Detection and Movement; Tanks Level Probing

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 341-2 V1.1.1 (2000-12) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile service (RP 02); Radio equipment

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-23 V1.2.1 (2002-11) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 300 422-2 V1.3.1 (2011-08) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range; Part 2: Harmonized

More information

ETSI EN V3.1.1 ( )

ETSI EN V3.1.1 ( ) EN 302 217-2 V3.1.1 (2017-05) HARMONISED EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 617-2 V2.1.1 (2015-12) HARMONISED EUROPEAN STANDARD Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonised

More information

ETSI EN V1.4.1 ( )

ETSI EN V1.4.1 ( ) EN 300 422-2 V1.4.1 (2015-06) HARMONIZED EUROPEAN STANDARD Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range; Part 2: Harmonized

More information

Final draft EN V1.1.2 ( )

Final draft EN V1.1.2 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); High capacity DRRS carrying 1 x Synchronous Transport Module-1 (1 x STM-1) signals

More information

Final draft ETSI EN V1.4.1 ( )

Final draft ETSI EN V1.4.1 ( ) Final draft EN 302 217-4-1 V1.4.1 (2009-09) European Standard (Telecommunications series) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4-1: System-dependent

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-13 V1.2.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 217-2-2 V2.1.1 (2013-07) Harmonized European Standard Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Digital systems operating in frequency

More information

Text Comparison. Documents Compared en_ v010301p.pdf. en_ v010501p.pdf

Text Comparison. Documents Compared en_ v010301p.pdf. en_ v010501p.pdf Text Comparison Documents Compared en_30033002v010301p.pdf en_30033002v010501p.pdf Summary 2506 word(s) added 4788 word(s) deleted 1608 word(s) matched 48 block(s) matched To see where the changes are,

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 220-4 V1.1.1 (2017-02) HARMONISED EUROPEAN STANDARD Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 4: Harmonised Standard covering the essential requirements

More information

ETSI TS V7.3.0 ( ) Technical Specification

ETSI TS V7.3.0 ( ) Technical Specification TS 151 026 V7.3.0 (2010-04) Technical Specification Digital cellular telecommunications system (Phase 2+); Base Station System (BSS) equipment specification; Part 4: Repeaters (3GPP TS 51.026 version 7.3.0

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 127 V1.1.1 (2000-09) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digital radio systems carrying SDH signals (2 x STM-1) in frequency

More information

Draft ETSI EN V3.0.8 ( )

Draft ETSI EN V3.0.8 ( ) Draft EN 302 217-2 V3.0.8 (2016-06) HARMONISED EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency

More information

Final draft ETSI EN V1.2.2 ( )

Final draft ETSI EN V1.2.2 ( ) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Portable Very High Frequency (VHF) radiotelephone equipment for the maritime mobile

More information

Summary 18/03/ :27:42. Differences exist between documents. Old Document: en_ v010501p 17 pages (97 KB) 18/03/ :27:35

Summary 18/03/ :27:42. Differences exist between documents. Old Document: en_ v010501p 17 pages (97 KB) 18/03/ :27:35 Summary 18/03/2016 16:27:42 Differences exist between documents. New Document: en_30067602v020101p 16 pages (156 KB) 18/03/2016 16:27:36 Used to display results. Old Document: en_30067602v010501p 17 pages

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 390 V1.2.1 (2003-11) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point and Multipoint Systems; Spurious emissions and receiver immunity limits at equipment/antenna

More information

ETSI TR V1.1.1 ( )

ETSI TR V1.1.1 ( ) TR 102 475 V1.1.1 (2006-07) Technical Report Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission Systems; Data transmission equipment operating in the 2,4 GHz ISM band

More information

Final draft ETSI EN V1.2.1 ( )

Final draft ETSI EN V1.2.1 ( ) Final draft EN 301 216 V1.2.1 (2001-03) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Plesiochronous Digital Hierarchy (PDH); Low and medium capacity and

More information

Draft EN V1.1.1 ( )

Draft EN V1.1.1 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); High capacity DRRS carrying STM-4 in two 40 MHz channels or 2 x STM-1 in a 40 MHz channel

More information

ETSI TS V4.0.0 ( )

ETSI TS V4.0.0 ( ) TS 151 026 V4.0.0 (2002-01) Technical Specification Digital cellular telecommunications system (Phase 2+); GSM Repeater Equipment Specification (3GPP TS 51.026 version 4.0.0 Release 4) GLOBAL SYSTEM FOR

More information

Draft ETSI EN V2.1.0 ( )

Draft ETSI EN V2.1.0 ( ) The present document can be downloaded from: Draft ETSI EN 302 208-2 V2.1.0 (2014-06) Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency Identification Equipment operating

More information

ETSI TS V1.1.1 ( )

ETSI TS V1.1.1 ( ) TS 100 220-1 V1.1.1 (1999-10) Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRDs); Measurement Specification for Wideband Transmitter Stability

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-17 V1.2.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 669 V1.1.1 (2000-06) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digital radio systems carrying STM-4 intwo40mhzchannelsor2xstm-1ina40mhz

More information

ETSI EN V2.3.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V2.3.1 ( ) Harmonized European Standard (Telecommunications series) EN 300 220-2 V2.3.1 (2010-02) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used

More information

Draft ETSI EN V1.1.0 ( )

Draft ETSI EN V1.1.0 ( ) Draft EN 303 372-2 V1.1.0 (2016-01) HARMONISED EUROPEAN STANDARD Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements

More information

SOUTH AFRICAN NATIONAL STANDARD

SOUTH AFRICAN NATIONAL STANDARD ISBN 978-0-626-32956-3 Edition 1 ETSI EN 300 639:2001 Edition V1.3.1 SOUTH AFRICAN NATIONAL STANDARD Fixed Radio Systems; Point-to-point equipment; Sub-STM-1 digital radio systems operating in the 13 GHz,

More information

ETSI TS V1.5.1 ( ) Technical Specification

ETSI TS V1.5.1 ( ) Technical Specification TS 100 392-15 V1.5.1 (2011-02) Technical Specification Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 15: TETRA frequency bands, duplex spacings and channel numbering 2 TS 100 392-15 V1.5.1

More information

ETSI EN V1.4.1 ( )

ETSI EN V1.4.1 ( ) EN 301 055 V1.4.1 (2001-02) European Standard (Telecommunications series) Fixed Radio Systems: Point-to-multipoint equipment; Direct Sequence Code Division Multiple Access (DS-CDMA); Point-to-multipoint

More information

ETSI TS V5.4.0 ( )

ETSI TS V5.4.0 ( ) Technical Specification Universal Mobile Telecommunications System (UMTS); UTRA Repeater; Radio transmission and reception () 1 Reference RTS/TSGR-0425106v540 Keywords UMTS 650 Route des Lucioles F-06921

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 124 V1.2.1 (2001-02) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-multipoint equipement; Direct Sequence Code Division Multiple Access (DS-CDMA) point-to-multipoint

More information

ETSI TS V1.4.1 ( ) Technical Specification

ETSI TS V1.4.1 ( ) Technical Specification TS 100 392-15 V1.4.1 (2010-03) Technical Specification Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 15: TETRA frequency bands, duplex spacings and channel numbering 2 TS 100 392-15 V1.4.1

More information

Draft ETSI EN V1.1.1 ( )

Draft ETSI EN V1.1.1 ( ) Draft EN 302 245-1 V1.1.1 (2004-05) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Transmitting equipment for the Digital Radio Mondiale (DRM)

More information

EUROPEAN ETS TELECOMMUNICATION September 1996 STANDARD

EUROPEAN ETS TELECOMMUNICATION September 1996 STANDARD EUROPEAN ETS 300 431 TELECOMMUNICATION September 1996 STANDARD Source: ETSI TC-TM Reference: DE/TM-04013 ICS: 33.080 Key words: digital, radio, DRRS Transmission and Multiplexing (TM); Digital fixed point-to-point

More information

This draft amendment A1, if approved, will modify the European Telecommunication Standard ETS (1996)

This draft amendment A1, if approved, will modify the European Telecommunication Standard ETS (1996) AMENDMENT ETS 300 786 pr A1 August 1999 Source: ETSI TC-TM Reference: RE/TM-04063-15/A1 Key words: DRRS, radio, SDH, STM, transmission This draft amendment A1, if approved, will modify the European Telecommunication

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 215-1 V1.1.1 (2000-06) European Standard (Telecommunications series) Fixed Radio Systems; Point to Multipoint Antennas; Antennas for point-to-multipoint fixed radio systems in the 11 GHz to 60 GHz

More information

Final draft ETSI EG V1.1.0 ( )

Final draft ETSI EG V1.1.0 ( ) Final draft EG 203 367 V1.1.0 (2016-03) GUIDE Guide to the application of harmonised standards covering articles 3.1b and 3.2 of the Directive 2014/53/EU (RED) to multi-radio and combined radio and non-radio

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 300 132-3 V1.2.1 (2003-08) European Standard (Telecommunications series) Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 3: Operated by rectified

More information

EN V1.2.2 ( )

EN V1.2.2 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Parameters for DRRS for the transmission of digital signals and analogue video signals

More information

EN V1.1.1 ( )

EN V1.1.1 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Direct Sequence Code Division Multiple Access (DS-CDMA) point-to-multipoint DRRS in

More information

ETSI TS V9.3.0 ( ) Technical Specification

ETSI TS V9.3.0 ( ) Technical Specification TS 136 106 V9.3.0 (2011-01) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (); FDD repeater radio transmission and reception (3GPP TS 36.106 version 9.3.0 Release 9) 1 TS 136 106

More information

ETSI TS V8.1.0 ( ) Technical Specification

ETSI TS V8.1.0 ( ) Technical Specification TS 125 144 V8.1.0 (2009-03) Technical Specification Universal Mobile Telecommunications System (UMTS); User Equipment (UE) and Mobile Station (MS) over the air performance requirements (3GPP TS 25.144

More information

EN V1.1.1 ( )

EN V1.1.1 ( ) European Standard (Telecommunications series) Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Part 1: Antennas for Point-to-Point (P-P) radio links in the 1 GHz to 3 GHz band European

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 489-26 V1.1.1 (2001-09) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 300 487 V2.1.2 (2016-11) HARMONISED EUROPEAN STANDARD Satellite Earth Stations and Systems (SES); Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating

More information

Final draft ETSI EN V2.1.1( )

Final draft ETSI EN V2.1.1( ) Final draft EN 300 132-3-0 V2.1.1(2011-10) European Standard Environmental Engineering (EE); Power supply interface at the input to telecommunications and datacom (ICT) equipment; Part 3: Operated by rectified

More information

Draft ETSI EN V2.1.0 ( )

Draft ETSI EN V2.1.0 ( ) Draft EN 300 487 V2.1.0 (2016-02) HARMONISED EUROPEAN STANDARD Satellite Earth Stations and Systems (SES); Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications

More information

ETSI ES V1.1.1 ( )

ETSI ES V1.1.1 ( ) ES 202 007 V1.1.1 (2002-03) Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Close Range peer-to-peer symmetrical Data Communication (CRDC) system 2 ES 202 007 V1.1.1 (2002-03)

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 301 091-2 V2.1.1 (2017-01) HARMONISED EUROPEAN STANDARD Short Range Devices; Transport and Traffic Telematics (TTT); Radar equipment operating in the 76 GHz to 77 GHz range; Harmonised Standard covering

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 841-3 V1.1.1 (2011-11) Harmonized European Standard VHF air-ground Digital Link (VDL) Mode 2; Technical characteristics and methods of measurement for ground-based equipment; Part 3: Harmonized

More information

ETSI TS V ( )

ETSI TS V ( ) TS 136 307 V8.11.0 (2014-03) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Requirements on User Equipments (UEs) supporting a release-independent frequency band (3GPP

More information

Draft ETSI EN V ( )

Draft ETSI EN V ( ) Draft EN 303 609 V12.4.1 (2016-01) HARMONISED EUROPEAN STANDARD Global System for Mobile communications (GSM); GSM Repeaters; Harmonised Standard covering the essential requirements of article 3.2 of the

More information

ETSI TS V8.0.0 ( ) Technical Specification

ETSI TS V8.0.0 ( ) Technical Specification TS 136 106 V8.0.0 (2009-01) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (); FDD repeater radio transmission and reception (3GPP TS 36.106 version 8.0.0 Release 8) 1 TS 136 106

More information

ETSI EN V1.4.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.4.1 ( ) Harmonized European Standard (Telecommunications series) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Cordless audio devices in the range 25 MHz to 2 000 MHz; Part 2: Harmonized EN covering

More information