WITH THE development of high brightness light emitting

Size: px
Start display at page:

Download "WITH THE development of high brightness light emitting"

Transcription

1 1410 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 3, MAY 2008 Quasi-Active Power Factor Correction Circuit for HB LED Driver Kening Zhou, Jian Guo Zhang, Subbaraya Yuvarajan, Senior Member, IEEE, and Da Feng Weng Abstract High brightness light emitting diodes (HB LEDs) are likely to be used for general lighting applications due to their high efficiency and longer life. The paper presents a quasi-active power factor corrector (PFC) for driving a string of HB LEDs. The singlestage PFC circuit has a high efficiency, and it does not increase the voltage/current stress on the active switch used in the switching converter due to PFC. The circuit has two operating modes based on the input voltage level and its features, like power factor correction and power balance, are explained. The experimental results obtained on a prototype converter along with waveforms are presented. Index Terms Driver, light emitting diodes (LEDs), power factor correction (PFC), pulse width modulation, switching converter. I. INTRODUCTION WITH THE development of high brightness light emitting diode (HB LED) technology, the output light efficiency of power LEDs has increased over 100 lumens/w [1]. The HB LED can be used as a solid state light source in general lighting applications. In addition to high efficiency, it has no mercury content and has a longer life. In the future, the power LED is likely to replace the existing lighting sources like the incandescent lamp and fluorescent lamp. For lamp drivers in general lighting applications, there are several regulations, e.g., harmonic limits on the input AC current have to meet Class C regulations for output power over 25 W [2]. Since the incandescent lamp is basically a resistor, it is easy to meet the requirement. For a fluorescent lamp, there are several power factor correction (PFC) circuits used in fluorescent lamp drivers or ballasts. It is the power factor correction circuit that makes the fluorescent ballast to meet Class C regulation. In general lighting applications, including fluorescent and HB-LED, power factor correction can be achieved using either a passive circuit or an active circuit. It is difficult to achieve a higher power factor and lower THD with a passive PFC which uses only inductors and capacitors, or with a variable inductive Manuscript received May 9, 2007; revised October 22, This paper was presented at the Applied Power Electronics Conference, Anaheim, CA, February 25-March 1, Recommended for publication by Associate Editor J. M. Alonso. K. Zhou is with the Zhejiang University of Science and Technology, Zhejiang, China. J. G. Zhang is with the ZhejiangUniversity, Hangzhou, Zhejiang, China. S. Yuvarajan is with the Department of Electrical Engineering, North Dakota State University, Fargo, ND USA ( subbaraya.yuvarajan@ndsu. edu). D. F. Weng is with MAXIM Integrated Products, Sunnyvale, CA USA. Color versions of one or more of the figures in this paper are available online at Digital Object Identifier /TPEL filter [3]. The active PFC on the other hand can provide a low THD and a high power factor. Single-switch AC-DC-DC converters with power factor correction combines boost PFC and forward or flyback converters [4], [5] and with load current feedback power control [6]. Active input current shaper is another solution of single switch AC-DC-DC converter with power factor correction function [7]. In general, the use of two power stages is a good way to implement power factor correction and to balance the input and output powers but it increases the cost. Single power stage with charge pump PFC has been used in the fluorescent AC-DC-AC ballast. For a single power stage AC-DC-DC converter with PFC, it is hard to balance the input and output powers [8] [11]. Also, there are high voltage and current stresses on the power components. A HB-LED driver (AC-DC-DC Converter) draws power from AC mains and supplies a DC current to the LED string. The driver needs a DC-DC converter to convert the input voltage into a DC current source and it limits the effectiveness of a charge pump. A single-power-stage AC-DC-DC converter with PFC is one candidate for HB LED drivers. The use of a single power stage increases the stress on the switch in the DC-DC converter due to input current and PFC voltage, and there is a power balance problem. This paper presents a quasi-active PFC scheme assisted by a power converter feeding a string of HB LEDs [12]. In the proposed quasi-active PFC scheme which precedes a driving power stage, a passive circuit is used to implement power factor correction function. The input current or PFC voltage stress is not added on to the active switch used in the following power (DC/DC) converter. It is the passive circuit implementing PFC function that increases the reliability and lowers the cost. It is the following power converter driving the passive PFC circuit that makes the size of the components in the passive circuit small. There are two operating modes in the circuit in which it is easy to balance the input and output powers. The principle of operation of the proposed HB-LED driver is explained and experimental results are presented. II. BASIC OPERATION AND MODES The basic quasi-active PFC circuit is shown in Fig. 1. It consists of a high frequency coupled inductor (C_Inductor), three valley-fill diodes ( and ), two DC bulk capacitors ( and ), and a resonant capacitor. The PFC supplies a discontinuous power load, such as, a buck, a buck-boost, a forward, or a flyback converter. In the present application, a buck-converter controlling the current through a set of HB LEDs constitutes the load. The operation of the PFC circuit falls under two working (operating) modes: (a) direct-feed mode (occurs when the instantaneous input line voltage is higher than the voltage of /$ IEEE

2 ZHOU et al.: QUASI-ACTIVE POWER FACTOR CORRECTION CIRCUIT FOR HB LED DRIVER 1411 Fig. 1. Basic quasi-active PFC circuit. Fig. 2. Equivalent circuits for direct-feed mode: (a) output current increasing; (b) output current decreasing. each DC bulk capacitor and ) and (b) coupled-boost mode (occurs when the input voltage is lower than the voltage of each DC bulk capacitor). a) Direct-Feed Mode: As the PFC s output current is changed from zero to a final (fixed) value, the input line will directly feed energy to the load and the resonant capacitor through the rectifier and the primary winding of C_inductor [Fig. 2(a)]. The load current passing through stores energy which will be released to the resonant capacitor and the capacitors and through when it goes to zero [Fig. 2(b)]. During this time, the input source charges the resonant capacitor and the two DC bulk capacitors and through. Because the output voltage of the bridge rectifier is less than the sum of the voltages on capacitors and, the charging current through will decay. It is clear that during this mode, the capacitors and store part of the input energy and their voltages increase. b) Coupled-Boost Mode: Since the input AC voltage is lower than the voltage on and during this mode, the resonant capacitor releases its stored energy resulting in a reduction in its voltage when the load current is changed from zero to a final (fixed) value. When the voltage on becomes lower than that on and, the two capacitors will release the stored energy to the load and the resonant capacitor [Fig. 3(a)]. The energy release corresponds to currents flowing through windings and of the coupled inductor and the stored energy. The coupled inductors and also resonate with the capacitor. As the load current goes back to zero, the coupled inductors and continue to resonate with, whose voltage increases. As the voltage across reflected to the secondary is less the voltage across and, diodes and turn off, and the stored magnetic energy in and is transferred to. The inductor will release the stored magnetic energy to the resonant capacitor, and. At the same time, the input power line will also directly feed energy to the capacitors, and, as shown in Fig. 3(b). It is clear that during this mode, the capacitors and release the stored energy to the load and have their voltage decrease. As shown in Fig. 1, the reflected load current is the current through the active switch in the following DC/DC converter or discontinuous current load. The current stress on the active switch is decided only by the output load current and it is independent of the input PFC current. The voltage stress on the active switch is determined by the maximum input voltage of the following DC/DC converter. The quasi-active PFC circuit has automatic voltage regulation that helps to keep the maximum DC bus voltage close to the amplitude of the input voltage for all load conditions. III. POWER FACTOR CORRECTION AND POWER BALANCE A. Power Factor Correction During the direct-feed mode, the current through is composed of two parts as shown in Fig. 4(a), the pulse current which is the reflected load current when the active switch of DC/DC converter turns on, and Fig. 4(b), the decaying current through. The slope of the decaying current is proportional to the difference between the input rectified AC voltage and the DC bus voltage. It is easy to see that the current through will decay slowly as the instantaneous rectified AC voltage approaches the DC bus voltage. It means that, as the rectified AC voltage gets close to the DC bus voltage, the average current through over one switching period will increase. The mathematical expression for the average input current during one switching period is given by where is the DC bus voltage; is the reflected load current; and are associated with, switching frequency, and. For a fixed switching frequency and a constant output (1) (2)

3 1412 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 3, MAY 2008 Fig. 3. Equivalent circuits for coupled-boost mode: (a) I increasing; (b) I decreasing (higher and lower reflected voltages). Fig. 4. Input current waveform for direct-feed mode. Fig. 6. Input current waveform for coupled-boost mode. Fig. 5. Plot of input current versus input voltage (d-f mode) current source, and are constants. The plot of versus is shown in Fig. 5. The input current varies linearly with the input voltage during the direct-feed mode, which means the input current follows the input voltage. During the coupled-boost mode, the input current is the current through which is decaying (Fig. 6). The average input current for a switching period is given by where is a constant associated with and switching frequency. The plot of versus is shown in Fig. 7. The relationship between the input current and the input voltage during the coupled-boost mode is almost linear, which means the input current follows the input voltage. Considering the plots shown in Figs. 5 and 7, it is seen that there is a linear relation between the input current and voltage that shows the inherent power factor correction function of the circuit. B. Power Balance The ratio between the time intervals for the direct feed and the coupled-boost mode depends on the ratio between the instantaneous input voltage and the voltage on or. In one AC cycle, as the voltage on and increases, the interval of (3) Fig. 7. Plot of input current versus input voltage (c-b mode). the coupled-boost mode increases, which means that the input power decreases. As the voltage on and deceases, the interval of coupled-boost mode decreases and the input power increases. Due to the automatic variation of the coupled-boost mode interval, it is easy to balance the input and output powers and make the maximum bus voltage closer to the amplitude of the input voltage for all load conditions. Suppose the output power decreases; the capacitors and will release less energy to the load during coupled-boost mode, which means the change (decrease) in the voltage on and is less. Thus, there is a reduction in the interval of the direct-feed mode and an increase in the interval of the coupledboost mode. This reduces the stored energy in the two DC bulk capacitors that balances the lower energy released by the bulk capacitors to the load. In the same way, the energy balance can be explained for the case of increasing output power. C. Design Considerations The quasi-active PFC circuit is a passive circuit driven by the discontinuous current pulses of the following DC-DC con-

4 ZHOU et al.: QUASI-ACTIVE POWER FACTOR CORRECTION CIRCUIT FOR HB LED DRIVER 1413 Fig. 8. HB LED driver with quasi-active power factor correction circuit. Fig. 9. Picture of the HB LED driver with quasi-active PFC demo board. verter (Fig. 8). To achieve the highest possible efficiency, the current in the coupled inductor under rated load should be continuous during most of the direct-feed interval and discontinuous during most of the coupled-boost mode interval. In this way, the current in is continuous most of the time and its amplitude is low thereby avoiding the use of a costly differential inductor. The value of the inductor is determined by the switching frequency and the value of the inductor in the downstream DC-DC converter. When the reflected load current steps up from zero to a certain level, the current in the inductor of the following DC-DC converter increases and the inductor stores the energy. The value of has very little effect on the current through the inductor in the DC-DC converter and the energy stored. This means that the value of the coupled inductor should be smaller than that of the inductor in the DC-DC converter. During the direct-feed interval, the coupled inductor transfers the input energy into the two DC bulk capacitors, which retain enough energy to supply output power during the coupled-boost mode interval. It is clear that, for a given inductor current, a higher inductor value will increase the energy stored in the DC capacitors. Based on the previously mentioned requirements, the value of inductor can be chosen to be between half and one-fourth that of the inductor in the DC-DC converter, that is where to 1/2. The turns-ratio of the coupled inductor is chosen as (4) (5) where and ) are the number of turns on the primary, secondary, and the third winding of the coupled inductor. By choosing a turns-ratio over 2, the dead time of the input current can be made zero. The values of the two bulk capacitors and depend on the the DC bus capacitor that is used in the regular AC-DC power supply, and they should be double the value of the capacitor as. The values of and can be made larger to make sure that the voltage ripple is less then 10%. In the circuit, the resonant capacitor controls the instant at which the coupled-boost mode starts. If the value of is zero, the coupled-boost mode will prevail until a current is set up in. The basic requirement is to have the coupled-boost mode operation only when the instantaneous ac input voltage is lower than the voltage on the capacitors and. Based on this requirement, the value of the reflected load current, and the value of the coupled inductor, the value of can be determined. IV. EXPERIMENTAL RESULTS The quasi-active PFC circuit is used as a HB LED driver for an output power of 30 W, as shown in Fig. 8. Ten 3-W LEDs from Cree (XLamp 7090 XL Series LED) are used as the load. The system efficiency is measured to be 88.05% (for a maximum load of 0.74 A at 40 V at V AC and W). The key components are: uh, uf/200 V, and uh. The picture of the demo board is shown in Fig. 9. The waveforms of the input AC voltage and current obtained are shown in Fig. 10. A digital power analyzer was used to obtain the harmonics in the input

5 1414 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 3, MAY 2008 Fig. 10. Waveforms of input voltage and current for the quasi-active PFC demo board. TABLE I HARMONIC IN THE INPUT CURRENT ALONG WITH CLASS C LIMITS current and the power factor. The harmonics present in the current along with the Class C limits are given in Table I. The THD is measured as 9.32% and the input power factor is measured as It is seen that the waveform of the input current is much closer to the sinusoidal waveform of the input current of an active-boost PFC converter and it meets Class C regulation. V. CONCLUSION A quasi-active PFC topology which can be used to drive HB LEDs is presented in this paper. It has no active switch in the PFC section, and the whole quasi-active PFC section is driven by the discontinuous input current of the following DC/DC power stage which actually supplies the HB LEDs.

6 ZHOU et al.: QUASI-ACTIVE POWER FACTOR CORRECTION CIRCUIT FOR HB LED DRIVER 1415 The quasi-active PFC section is subjected to the switching frequency of the following DC/DC converter. Hence, its efficiency and reliability are higher and the size and cost are lower. The test results on a prototype shows that the total harmonic distortion (THD) is below 10% and the efficiency is also high. Kening Zhou received the B.S. and M.S. degrees in electrical engineering from Zhejiang University, Hangzhou, China, in 1982 and 1998, respectively. He is presently an Associate Professor at the Zhejiang University of Science and Technology, Zhejiang, China. His main study area includes electric-measurement-control technology and power electronics technology. REFERENCES [1] HB LED Market Outlook detailed at Industry Conf. [Online]. Available: [2] M. OLeary, Plug in safeguard AC power line quality, EDN, pp , Mar. 18, [3] W. H. Wolfle and G. Hurley, Quasi-active power factor correction with a variable inductive filter: Theory, design, and practice, IEEE Trans. Power Electron., vol. 18, no. 1, pp , Jan [4] H. Wei, I. Batarseh, G. Zhu, and P. Kornetzky, A single-switch AD-DC converter with power factor correction, IEEE Trans. Power Electron., vol. 15, no. 3, pp , May [5] R. Redl, L. Balogh, and N. O. Sokal, A new family of single-stage isolated power-factor correctors with fast regulation of the output voltage, in Proc. IEEE Power Electronics Specialists Conf., 1994, pp [6] Q. Zhao, M. Xu, F. C. Lee, and J. Qian, Single-switch parallel power factor correction AC-DC converters with inherent load current feedback, IEEE Trans. Power Electron., vol. 19, no. 4, pp , Jul [7] J. Sebastian, A. Femandez, P. Villegas, M. Hemando, and J. Prieto, New topologies of active input current shapers to allow AC-to-DC converters to comply with the IEC , IEEE Trans. Power Electron., vol. 17, no. 4, pp , Jul [8] M. H. L. Chow, K. W. Siu, C. K. Tse, and Y.-S. Lee, A novel method for elimination of line-current harmonics in single-stage PFC switching regulators, IEEE Trans. Power Electron., vol. 13, no. 1, pp , Jan [9] M. H. L. Chow, Y. S. Lee, and C. K. Tse, Single-stage single-switch isolated PFC regulator with unity power factor, fast transient response and low voltage stress, in Proc. IEEE Power Electronics Specialists Conf., 1998, pp [10] M. M. Jovanovic, D. M. Tsang, and F. C. Lee, Reduction of voltage stress in integrated high-quality rectifier-regulators by variable frequency control, in Proc. IEEE Applied Power Electronics Conf., 1994, pp [11] C. Qiao and K. M. Smedley, A topology survey of single-stage power factor corrector with a boost type input-current-shaper, IEEE Trans. Power Electron., vol. 16, no. 3, pp , May [12] D. F. Weng, Quasi-active power factor correction circuit for switching power supply, U.S. Patent # , Jun Jian Guo Zhang received the Associate degree in optic engineering from Zhejiang University, Hangzhou, China, in His main study area includes computer network and digital and power electronic technology. Subbaraya Yuvarajan (SM 84) received the M.Tech. and Ph.D. degrees from the Indian Institute of Technology, Chennai, Madras, India, in 1969 and 1981, respectively. He was with the Department of Electrical Engineering, PSG College of Technology, from 1969 to 1974, and with the Indian Institute of Technology from 1974 to He joined the Department of Electrical and Computer Engineering, North Dakota State University, Fargo, in 1983, where his currently a Professor. His research interests include high-performance power supplies and power conversion for renewable energy sources like PV power and PEM fuel cell. Da Feng Weng received the B.S. and M.E. degrees in electrical engineering from Zhejiang University, Hangzhou, China, in 1982 and 1985, respectively, and the Ph.D. degree in electrical engineering from North Dakota State University, Fargo, in He has worked in several lighting and semiconductor industries, including Magne Tek, Matsushita Electric Works, Philips Research, Analog devices, Intersil, and he is currently with MAXIM Integrated Products. His research includes power electronics topology and control.

THREE-PHASE converters are used to handle large powers

THREE-PHASE converters are used to handle large powers IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 6, NOVEMBER 1999 1149 Resonant-Boost-Input Three-Phase Power Factor Corrector Da Feng Weng, Member, IEEE and S. Yuvarajan, Senior Member, IEEE Abstract

More information

Boost Converter for Power Factor Correction of DC Motor Drive

Boost Converter for Power Factor Correction of DC Motor Drive International Journal of Electrical, Electronics and Telecommunication Engineering, Vol. 43, Special Issue: 3 51 Boost Converter for Power Factor Correction of DC Motor Drive K.VENKATESWARA RAO M-Tech

More information

AC/DC Converter with Active Power Factor Correction Applied to DC Motor Drive

AC/DC Converter with Active Power Factor Correction Applied to DC Motor Drive International Journal of Engineering Research and Development ISSN: 2278-067X, Volume 1, Issue 11 (July 2012), PP. 58-66 www.ijerd.com AC/DC Converter with Active Power Factor Correction Applied to DC

More information

MODERN switching power converters require many features

MODERN switching power converters require many features IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 19, NO. 1, JANUARY 2004 87 A Parallel-Connected Single Phase Power Factor Correction Approach With Improved Efficiency Sangsun Kim, Member, IEEE, and Prasad

More information

A Single Phase Single Stage AC/DC Converter with High Input Power Factor and Tight Output Voltage Regulation

A Single Phase Single Stage AC/DC Converter with High Input Power Factor and Tight Output Voltage Regulation 638 Progress In Electromagnetics Research Symposium 2006, Cambridge, USA, March 26-29 A Single Phase Single Stage AC/DC Converter with High Input Power Factor and Tight Output Voltage Regulation A. K.

More information

POWER FACTOR CORRECTION USING AN IMPROVED SINGLE-STAGE SINGLE- SWITCH (S 4 ) TECHNIQUE

POWER FACTOR CORRECTION USING AN IMPROVED SINGLE-STAGE SINGLE- SWITCH (S 4 ) TECHNIQUE International Journal of Power Systems and Microelectronics (IJMPS) Vol. 1, Issue 1, Jun 2016, 45-52 TJPRC Pvt. Ltd POWER FACTOR CORRECTION USING AN IMPROVED SINGLE-STAGE SINGLE- SWITCH (S 4 ) TECHNIQUE

More information

Comparative Analysis of Power Factor Correction Techniques for AC/DC Converter at Various Loads

Comparative Analysis of Power Factor Correction Techniques for AC/DC Converter at Various Loads ISSN 2393-82 Vol., Issue 2, October 24 Comparative Analysis of Power Factor Correction Techniques for AC/DC Converter at Various Loads Nikita Kolte, N. B. Wagh 2 M.Tech.Research Scholar, PEPS, SDCOE, Wardha(M.S.),India

More information

Student Department of EEE (M.E-PED), 2 Assitant Professor of EEE Selvam College of Technology Namakkal, India

Student Department of EEE (M.E-PED), 2 Assitant Professor of EEE Selvam College of Technology Namakkal, India Design and Development of Single Phase Bridgeless Three Stage Interleaved Boost Converter with Fuzzy Logic Control System M.Pradeep kumar 1, M.Ramesh kannan 2 1 Student Department of EEE (M.E-PED), 2 Assitant

More information

Power Factor Improvement With High Efficiency Converters

Power Factor Improvement With High Efficiency Converters Power Factor Improvement With High Efficiency Converters P. YOHAN BABU, P.SURENDRA BABU, K. Ravi Chandrudu, G.V.P. Anjaneyulu Abstract New recommendations and future standards have increased the interest

More information

Narasimharaju. Balaraju *1, B.Venkateswarlu *2

Narasimharaju. Balaraju *1, B.Venkateswarlu *2 Narasimharaju.Balaraju*, et al, [IJRSAE]TM Volume 2, Issue 8, pp:, OCTOBER 2014. A New Design and Development of Step-Down Transformerless Single Stage Single Switch AC/DC Converter Narasimharaju. Balaraju

More information

IN THE high power isolated dc/dc applications, full bridge

IN THE high power isolated dc/dc applications, full bridge 354 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 2, MARCH 2006 A Novel Zero-Current-Transition Full Bridge DC/DC Converter Junming Zhang, Xiaogao Xie, Xinke Wu, Guoliang Wu, and Zhaoming Qian,

More information

Webpage: Volume 3, Issue IV, April 2015 ISSN

Webpage:  Volume 3, Issue IV, April 2015 ISSN CLOSED LOOP CONTROLLED BRIDGELESS PFC BOOST CONVERTER FED DC DRIVE Manju Dabas Kadyan 1, Jyoti Dabass 2 1 Rattan Institute of Technology & Management, Department of Electrical Engg., Palwal-121102, Haryana,

More information

SINGLE-STAGE HIGH-POWER-FACTOR SELF-OSCILLATING ELECTRONIC BALLAST FOR FLUORESCENT LAMPS WITH SOFT START

SINGLE-STAGE HIGH-POWER-FACTOR SELF-OSCILLATING ELECTRONIC BALLAST FOR FLUORESCENT LAMPS WITH SOFT START SINGLE-STAGE HIGH-POWER-FACTOR SELF-OSCILLATING ELECTRONIC BALLAST FOR FLUORESCENT S WITH SOFT START Abstract: In this paper a new solution to implement and control a single-stage electronic ballast based

More information

SINGLE-stage ac dc converters simultaneously perform

SINGLE-stage ac dc converters simultaneously perform 3714 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 27, NO. 8, AUGUST 2012 A Low-Power AC DC Single-Stage Converter With Reduced DC Bus Voltage Variation Navid Golbon, Student Member, IEEE, and Gerry Moschopoulos,

More information

A Novel Single-Stage Push Pull Electronic Ballast With High Input Power Factor

A Novel Single-Stage Push Pull Electronic Ballast With High Input Power Factor 770 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 48, NO. 4, AUGUST 2001 A Novel Single-Stage Push Pull Electronic Ballast With High Input Power Factor Chang-Shiarn Lin, Member, IEEE, and Chern-Lin

More information

RECENTLY, the harmonics current in a power grid can

RECENTLY, the harmonics current in a power grid can IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 2, MARCH 2008 715 A Novel Three-Phase PFC Rectifier Using a Harmonic Current Injection Method Jun-Ichi Itoh, Member, IEEE, and Itsuki Ashida Abstract

More information

IN ORDER to reduce the low-frequency current harmonic

IN ORDER to reduce the low-frequency current harmonic 1472 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 54, NO. 3, JUNE 2007 Optimizing the Design of Single-Stage Power-Factor Correctors José A. Villarejo, Member, IEEE, Javier Sebastián, Member, IEEE,

More information

Modified Ac-Dc Single-Stage Converters

Modified Ac-Dc Single-Stage Converters 44 Journal of Power Electronics, Vol 7, No 1, January 2007 JPE 7-1-6 Modified Ac-c Single-Stage Converters Gerry Moschopoulos *, Yan Liu *, and Sondeep Bassan * * epartment of Electrical and Computer Engineering,

More information

A Novel Bridgeless Single-Stage Half-Bridge AC/DC Converter

A Novel Bridgeless Single-Stage Half-Bridge AC/DC Converter A Novel Bridgeless Single-Stage Half-Bridge AC/DC Converter Woo-Young Choi 1, Wen-Song Yu, and Jih-Sheng (Jason) Lai Virginia Polytechnic Institute and State University Future Energy Electronics Center

More information

An Interleaved Single-Stage Fly Back AC-DC Converter for Outdoor LED Lighting Systems

An Interleaved Single-Stage Fly Back AC-DC Converter for Outdoor LED Lighting Systems An Interleaved Single-Stage Fly Back AC-DC Converter for Outdoor LED Lighting Systems 1 Sandhya. K, 2 G. Sharmila 1. PG Scholar, Department of EEE, Maharaja Institute of Technology, Coimbatore, Tamil Nadu.

More information

Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation

Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation V. Ravi 1, M. Venkata Kishore 2 and C. Ashok kumar 3 Balaji Institute of Technology & Sciences,

More information

New Efficient Bridgeless Cuk Rectifiers for PFC Application on d.c machine

New Efficient Bridgeless Cuk Rectifiers for PFC Application on d.c machine International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 9, Issue 1 (November 2013), PP. 15-21 New Efficient Bridgeless Cuk Rectifiers for

More information

Performance Improvement of Bridgeless Cuk Converter Using Hysteresis Controller

Performance Improvement of Bridgeless Cuk Converter Using Hysteresis Controller International Journal of Electrical Engineering. ISSN 0974-2158 Volume 6, Number 1 (2013), pp. 1-10 International Research Publication House http://www.irphouse.com Performance Improvement of Bridgeless

More information

466 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY A Single-Switch Flyback-Current-Fed DC DC Converter

466 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY A Single-Switch Flyback-Current-Fed DC DC Converter 466 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY 1998 A Single-Switch Flyback-Current-Fed DC DC Converter Peter Mantovanelli Barbosa, Member, IEEE, and Ivo Barbi, Senior Member, IEEE Abstract

More information

Linear Transformer based Sepic Converter with Ripple Free Output for Wide Input Range Applications

Linear Transformer based Sepic Converter with Ripple Free Output for Wide Input Range Applications Linear Transformer based Sepic Converter with Ripple Free Output for Wide Input Range Applications Karthik Sitapati Professor, EEE department Dayananda Sagar college of Engineering Bangalore, India Kirthi.C.S

More information

Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation

Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation Ms.K.Swarnalatha #1, Mrs.R.Dheivanai #2, Mr.S.Sundar #3 #1 EEE Department, PG Scholar, Vivekanandha

More information

THE converter usually employed for single-phase power

THE converter usually employed for single-phase power 82 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 46, NO. 1, FEBRUARY 1999 A New ZVS Semiresonant High Power Factor Rectifier with Reduced Conduction Losses Alexandre Ferrari de Souza, Member, IEEE,

More information

Isolated AC/DC Offline High Power Factor Single-Switch Led Driver Using Fuzzy Logic Controller

Isolated AC/DC Offline High Power Factor Single-Switch Led Driver Using Fuzzy Logic Controller Middle-East Journal of Scientific Research 24 (Recent Innovations in Engineering, Technology, Management & Applications): 90-94, 2016 ISSN 1990-9233; IDOSI Publications, 2016 DOI: 10.5829/idosi.mejsr.2016.24.RIETMA115

More information

SCIENCE & TECHNOLOGY

SCIENCE & TECHNOLOGY Pertanika J. Sci. & Technol. 25 (S): 9-18 (2017) SCIENCE & TECHNOLOGY Journal homepage: http://www.pertanika.upm.edu.my/ A Single-stage LED Driver with Voltage Doubler Rectifier Nurul Asikin, Zawawi 1

More information

Power Factor Correction of LED Drivers with Third Port Energy Storage

Power Factor Correction of LED Drivers with Third Port Energy Storage Power Factor Correction of LED Drivers with Third Port Energy Storage Saeed Anwar Mohamed O. Badawy Yilmaz Sozer sa98@zips.uakron.edu mob4@zips.uakron.edu ys@uakron.edu Electrical and Computer Engineering

More information

PWM Switched Double Stage Buck Boost Converter with LC Filter for LED Lighting Applications

PWM Switched Double Stage Buck Boost Converter with LC Filter for LED Lighting Applications PWM Switched Double Stage Buck Boost Converter with LC Filter for LED Lighting Applications Akhiljith P.J 1, Leena Thomas 2, Ninu Joy 3 P.G. student, Mar Athanasius College of Engineering, Kothamangalam,

More information

Design and Simulation of New Efficient Bridgeless AC- DC CUK Rectifier for PFC Application

Design and Simulation of New Efficient Bridgeless AC- DC CUK Rectifier for PFC Application Design and Simulation of New Efficient Bridgeless AC- DC CUK Rectifier for PFC Application Thomas Mathew.T PG Student, St. Joseph s College of Engineering, C.Naresh, M.E.(P.hd) Associate Professor, St.

More information

POWERED electronic equipment with high-frequency inverters

POWERED electronic equipment with high-frequency inverters IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II: EXPRESS BRIEFS, VOL. 53, NO. 2, FEBRUARY 2006 115 A Novel Single-Stage Power-Factor-Correction Circuit With High-Frequency Resonant Energy Tank for DC-Link

More information

SINGLE STAGE LOW FREQUENCY ELECTRONIC BALLAST FOR HID LAMPS

SINGLE STAGE LOW FREQUENCY ELECTRONIC BALLAST FOR HID LAMPS SINGLE STAGE LOW FREQUENCY ELECTRONIC BALLAST FOR HID LAMPS SUMAN TOLANUR 1 & S.N KESHAVA MURTHY 2 1,2 EEE Dept., SSIT Tumkur E-mail : sumantolanur@gmail.com Abstract - The paper presents a single-stage

More information

Flyback with Half Wave Rectifier for Single Stage Power Factor Correction K.Umamaheswari*, V.Venkatachalam ** *

Flyback with Half Wave Rectifier for Single Stage Power Factor Correction K.Umamaheswari*, V.Venkatachalam ** * International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 473 Flyback with Half Wave Rectifier for Single Stage Power Factor Correction K.Umamaheswari*, V.Venkatachalam

More information

Integrated Buck-Buck-Boost AC/DC Converter

Integrated Buck-Buck-Boost AC/DC Converter ISSN (Online): 347-3878 Volume Issue 1, January 014 Integrated Buck-Buck-Boost AC/DC Converter Supriya. K 1, Maheswaran. K 1 M.Tech (Power Electronics & Drives), Department of EEE, Nehru College of Engineering

More information

FOR THE DESIGN of high input voltage isolated dc dc

FOR THE DESIGN of high input voltage isolated dc dc 38 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 1, JANUARY 2008 Dual Interleaved Active-Clamp Forward With Automatic Charge Balance Regulation for High Input Voltage Application Ting Qian and Brad

More information

Controlled Single Switch Step down AC/DC Converter without Transformer

Controlled Single Switch Step down AC/DC Converter without Transformer International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 9, Issue 12 (February 2014), PP. 34-38 Controlled Single Switch Step down AC/DC

More information

A New Single Switch Bridgeless SEPIC PFC Converter with Low Cost, Low THD and High PF

A New Single Switch Bridgeless SEPIC PFC Converter with Low Cost, Low THD and High PF A New Single Switch Bridgeless SEPIC PFC Converter with ow Cost, ow THD and High PF Yasemin Onal, Yilmaz Sozer The University of Bilecik Seyh Edebali, Department of Electrical and Electronic Engineering,

More information

A NEW SINGLE STAGE THREE LEVEL ISOLATED PFC CONVERTER FOR LOW POWER APPLICATIONS

A NEW SINGLE STAGE THREE LEVEL ISOLATED PFC CONVERTER FOR LOW POWER APPLICATIONS A NEW SINGLE STAGE THREE LEVEL ISOLATED PFC CONVERTER FOR LOW POWER APPLICATIONS S.R.Venupriya 1, Nithyananthan.K 2, Ranjidharan.G 3, Santhosh.M 4,Sathiyadevan.A 5 1 Assistant professor, 2,3,4,5 Students

More information

A NOVEL CONTROL SCHEME OF QUASI- RESONANT VALLEY-SWITCHING FOR HIGH- POWER FACTOR AC TO DC LED DRIVERS

A NOVEL CONTROL SCHEME OF QUASI- RESONANT VALLEY-SWITCHING FOR HIGH- POWER FACTOR AC TO DC LED DRIVERS Int. J. Engg. Res. & Sci. & Tech. 2015 V Maheskumar and T Poornipriya, 2015 Research Paper ISSN 2319-5991 www.ijerst.com Vol. 4, No. 4, November 2015 2015 IJERST. All Rights Reserved A NOVEL CONTROL SCHEME

More information

A Unique SEPIC converter based Power Factor Correction method with a DCM Detection Technique

A Unique SEPIC converter based Power Factor Correction method with a DCM Detection Technique IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 11, Issue 4 Ver. III (Jul. Aug. 2016), PP 01-06 www.iosrjournals.org A Unique SEPIC converter

More information

Performance comparison of Quasi-Z-Source inverter with conventional Z-source inverter

Performance comparison of Quasi-Z-Source inverter with conventional Z-source inverter International Journal of Electrical Engineering. ISSN 0974-2158 Volume 8, Number 3 (2015), pp. 225-238 International Research Publication House http://www.irphouse.com Performance comparison of Quasi-Z-Source

More information

SSRG International Journal of Electrical and Electronics Engineering (SSRG-IJEEE) volume 1 Issue 10 Dec 2014

SSRG International Journal of Electrical and Electronics Engineering (SSRG-IJEEE) volume 1 Issue 10 Dec 2014 Soft switching power factor correction of Single Phase and Three Phases boost converter V. Praveen M.Tech, 1 V. Masthanaiah 2 1 (Asst.Professor, Visvodaya engineering college, Kavali, SPSR Nellore Dt.

More information

Single Phase Bridgeless SEPIC Converter with High Power Factor

Single Phase Bridgeless SEPIC Converter with High Power Factor International Journal of Emerging Engineering Research and Technology Volume 2, Issue 6, September 2014, PP 117-126 ISSN 2349-4395 (Print) & ISSN 2349-4409 (Online) Single Phase Bridgeless SEPIC Converter

More information

Comparison between the Performance of Basic SEPIC Converter and modified SEPIC Converter with PI Controller

Comparison between the Performance of Basic SEPIC Converter and modified SEPIC Converter with PI Controller Research Paper American Journal of Engineering Research (AJER) 2014 American Journal of Engineering Research (AJER) e-issn : 2320-0847 p-issn : 2320-0936 Volume-03, Issue-08, pp-180-186 www.ajer.org Open

More information

DUE TO THE increased awareness of the many undesirable

DUE TO THE increased awareness of the many undesirable IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 1, JANUARY 1998 75 A Novel Method for Elimination of Line-Current Harmonics in Single-Stage PFC Switching Regulators Martin H. L. Chow, K. W. Siu, Chi

More information

Integration of Two Flyback Converters at Input PFC Stage for Lighting Applications

Integration of Two Flyback Converters at Input PFC Stage for Lighting Applications Integration of Two Flyback Converters at Input PFC Stage for Lighting Applications Anjali.R.N 1, K. Shanmukha Sundar 2 PG student [Power Electronics], Dept. of EEE, Dayananda Sagar College of Engineering,

More information

Single Phase Converters for Power Factor Correction with Tight Output Voltage Regulation

Single Phase Converters for Power Factor Correction with Tight Output Voltage Regulation Single Phase Converters for Power Factor Correction with Tight Output Voltage Regulation K. Umamaheswari 1, V. Venkatachalam 2 1 Research Scholar, Anna University, Chennai 2 Principal, The Kavery Engineering

More information

ENERGY saving through efficient equipment is an essential

ENERGY saving through efficient equipment is an essential IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 61, NO. 9, SEPTEMBER 2014 4649 Isolated Switch-Mode Current Regulator With Integrated Two Boost LED Drivers Jae-Kuk Kim, Student Member, IEEE, Jae-Bum

More information

A HIGH STEP UP RESONANT BOOST CONVERTER USING ZCS WITH PUSH-PULL TOPOLOGY

A HIGH STEP UP RESONANT BOOST CONVERTER USING ZCS WITH PUSH-PULL TOPOLOGY A HIGH STEP UP RESONANT BOOST CONVERTER USING ZCS WITH PUSH-PULL TOPOLOGY Maheswarreddy.K, PG Scholar. Suresh.K, Assistant Professor Department of EEE, R.G.M College of engineering, Kurnool (D), Andhra

More information

NOWADAYS, it is not enough to increase the power

NOWADAYS, it is not enough to increase the power IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 44, NO. 5, OCTOBER 1997 597 An Integrated Battery Charger/Discharger with Power-Factor Correction Carlos Aguilar, Student Member, IEEE, Francisco Canales,

More information

Simulation and Performance Evaluation of Closed Loop Pi and Pid Controlled Sepic Converter Systems

Simulation and Performance Evaluation of Closed Loop Pi and Pid Controlled Sepic Converter Systems Simulation and Performance Evaluation of Closed Loop Pi and Pid Controlled Sepic Converter Systems Simulation and Performance Evaluation of Closed Loop Pi and Pid Controlled Sepic Converter Systems T.

More information

CHAPTER 3. SINGLE-STAGE PFC TOPOLOGY GENERALIZATION AND VARIATIONS

CHAPTER 3. SINGLE-STAGE PFC TOPOLOGY GENERALIZATION AND VARIATIONS CHAPTER 3. SINGLE-STAGE PFC TOPOLOG GENERALIATION AND VARIATIONS 3.1. INTRODUCTION The original DCM S 2 PFC topology offers a simple integration of the DCM boost rectifier and the PWM DC/DC converter.

More information

UNITY POWER FACTOR CORRECTION USING THE BI-BOOST TOPOLOGY WITH A FORWARD CONTROL TECHNIQUE

UNITY POWER FACTOR CORRECTION USING THE BI-BOOST TOPOLOGY WITH A FORWARD CONTROL TECHNIQUE 8 th International Conference on DEVELOPMENT AND APPLICATION SYSTEMS S u c e a v a, R o m a n i a, M a y 25 27, 2 0 0 6 UNITY POWER FACTOR CORRECTION USING THE BI-BOOST TOPOLOGY WITH A FORWARD CONTROL

More information

International Journal of Scientific & Engineering Research, Volume 5, Issue 3, March-2014 ISSN

International Journal of Scientific & Engineering Research, Volume 5, Issue 3, March-2014 ISSN 332 An Improved Bridgeless SEPIC PFC Converter N. Madhumitha, Dr C. Christober Asir Rajan Department of Electrical & Electronics Engineering Pondicherry Engineering College madhudeez@pec.edu, asir_70@pec.edu

More information

A Double ZVS-PWM Active-Clamping Forward Converter: Analysis, Design, and Experimentation

A Double ZVS-PWM Active-Clamping Forward Converter: Analysis, Design, and Experimentation IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 6, NOVEMBER 2001 745 A Double ZVS-PWM Active-Clamping Forward Converter: Analysis, Design, and Experimentation René Torrico-Bascopé, Member, IEEE, and

More information

IN recent years, the development of high power isolated bidirectional

IN recent years, the development of high power isolated bidirectional IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 2, MARCH 2008 813 A ZVS Bidirectional DC DC Converter With Phase-Shift Plus PWM Control Scheme Huafeng Xiao and Shaojun Xie, Member, IEEE Abstract The

More information

A Predictive Control Strategy for Power Factor Correction

A Predictive Control Strategy for Power Factor Correction IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 8, Issue 6 (Nov. - Dec. 2013), PP 07-13 A Predictive Control Strategy for Power Factor Correction

More information

Bridgeless Cuk Power Factor Corrector with Regulated Output Voltage

Bridgeless Cuk Power Factor Corrector with Regulated Output Voltage Bridgeless Cuk Power Factor Corrector with Regulated Output Voltage Ajeesh P R 1, Prof. Dinto Mathew 2, Prof. Sera Mathew 3 1 PG Scholar, 2,3 Professors, Department of Electrical and Electronics Engineering,

More information

BRIDGELESS SEPIC CONVERTER FOR POWER FACTOR IMPROVEMENT

BRIDGELESS SEPIC CONVERTER FOR POWER FACTOR IMPROVEMENT BRIDGELESS SEPIC CONVERTER FOR POWER FACTOR IMPROVEMENT Hemalatha Gunasekaran Department of EEE, Pondicherry Engineering college, Pillaichavady, Puducherry, INDIA hemalathagunasekarancluny@gmail.com Dr.

More information

IT is well known that the boost converter topology is highly

IT is well known that the boost converter topology is highly 320 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 2, MARCH 2006 Analysis and Design of a Low-Stress Buck-Boost Converter in Universal-Input PFC Applications Jingquan Chen, Member, IEEE, Dragan Maksimović,

More information

Multilevel inverter with cuk converter for grid connected solar PV system

Multilevel inverter with cuk converter for grid connected solar PV system I J C T A, 9(5), 2016, pp. 215-221 International Science Press Multilevel inverter with cuk converter for grid connected solar PV system S. Dellibabu 1 and R. Rajathy 2 ABSTRACT A Multilevel Inverter with

More information

Hardware Implementation of Two-Phase Bridgeless Interleaved Boost Converter for Power Factor Correction

Hardware Implementation of Two-Phase Bridgeless Interleaved Boost Converter for Power Factor Correction Hardware Implementation of Two-Phase Bridgeless Interleaved Boost Converter for Power Factor Correction Authors & Affiliation: Dr.R.Seyezhai*, V.Abhineya**, M.Aishwarya** & K.Gayathri** *Associate Professor,

More information

THE increasing tension on the global energy supply has resulted

THE increasing tension on the global energy supply has resulted IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 27, NO. 4, APRIL 2012 1885 Single-Stage Boost Inverter With Coupled Inductor Yufei Zhou, Student Member, IEEE, and Wenxin Huang, Member, IEEE Abstract Renewable

More information

A HIGH RELIABILITY SINGLE-PHASE BOOST RECTIFIER SYSTEM FOR DIFFERENT LOAD VARIATIONS. Prasanna Srikanth Polisetty

A HIGH RELIABILITY SINGLE-PHASE BOOST RECTIFIER SYSTEM FOR DIFFERENT LOAD VARIATIONS. Prasanna Srikanth Polisetty GRT A HIGH RELIABILITY SINGLE-PHASE BOOST RECTIFIER SYSTEM FOR DIFFERENT LOAD VARIATIONS Prasanna Srikanth Polisetty Department of Electrical and Electronics Engineering, Newton s College of Engineering

More information

A COMPARATIVE STUDY OF ACTIVE POWER FACTOR CORRECTION AC-DC CONVERTERS FOR ELECTRIC VEHICLE APPLICATIONS

A COMPARATIVE STUDY OF ACTIVE POWER FACTOR CORRECTION AC-DC CONVERTERS FOR ELECTRIC VEHICLE APPLICATIONS A COMPARATIVE STUDY OF ACTIVE POWER FACTOR CORRECTION AC-DC CONVERTERS FOR ELECTRIC VEHICLE APPLICATIONS A. Inba Rexy 1 and R. Seyezhai 2 1 Department of EEE, Loyola-ICAM College of Engineering and Technology,

More information

Reduction of Voltage Stresses in Buck-Boost-Type Power Factor Correctors Operating in Boundary Conduction Mode

Reduction of Voltage Stresses in Buck-Boost-Type Power Factor Correctors Operating in Boundary Conduction Mode Reduction of oltage Stresses in Buck-Boost-Type Power Factor Correctors Operating in Boundary Conduction Mode ars Petersen Institute of Electric Power Engineering Technical University of Denmark Building

More information

AN EFFICIENT CLOSED LOOP CONTROLLED BRIDGELESS CUK RECTIFIER FOR PFC APPLICATIONS

AN EFFICIENT CLOSED LOOP CONTROLLED BRIDGELESS CUK RECTIFIER FOR PFC APPLICATIONS AN EFFICIENT CLOSED LOOP CONTROLLED BRIDGELESS CUK RECTIFIER FOR PFC APPLICATIONS Shalini.K 1, Murthy.B 2 M.E. (Power Electronics and Drives) Department of Electrical and Electronics Engineering, C.S.I.

More information

SINGLE-STAGE power factor correction (PFC) ac-dc converters

SINGLE-STAGE power factor correction (PFC) ac-dc converters 384 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 54, NO. 1, FEBRUARY 2007 New Power Factor Correction AC-DC Converter With Reduced Storage Capacitor Voltage Antonio Lázaro, Member, IEEE, Andrés Barrado,

More information

Single Phase Single Stage Power Factor Correction Converter with Phase Shift PWM Technique

Single Phase Single Stage Power Factor Correction Converter with Phase Shift PWM Technique Single Phase Single Stage Power Factor Correction Converter with Phase Shift PWM Technique G.KAVIARASAN 1, M.G ANAND 2 1 PG Scholar, Department of Power Electronics and Drives THE KAVERY ENGINEERNG COLLEGE,salem

More information

A New Soft Recovery PWM Quasi-Resonant Converter With a Folding Snubber Network

A New Soft Recovery PWM Quasi-Resonant Converter With a Folding Snubber Network 456 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 49, NO. 2, APRIL 2002 A New Soft Recovery PWM Quasi-Resonant Converter With a Folding Snubber Network Jin-Kuk Chung, Student Member, IEEE, and Gyu-Hyeong

More information

BIDIRECTIONAL dc dc converters are widely used in

BIDIRECTIONAL dc dc converters are widely used in 816 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II: EXPRESS BRIEFS, VOL. 62, NO. 8, AUGUST 2015 High-Gain Zero-Voltage Switching Bidirectional Converter With a Reduced Number of Switches Muhammad Aamir,

More information

Analysis, Design and Development of a Single Switch Flyback Buck-Boost AC-DC Converter for Low Power Battery Charging Applications

Analysis, Design and Development of a Single Switch Flyback Buck-Boost AC-DC Converter for Low Power Battery Charging Applications 318 Journal of Power Electronics, Vol. 7, No. 4, October 007 JPE 7-4-7 Analysis, Design and Development of a Single Switch Flyback Buck-Boost AC-DC Converter for Low Power Battery Charging Applications

More information

THE classical solution of ac dc rectification using a fullwave

THE classical solution of ac dc rectification using a fullwave 630 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 44, NO. 5, OCTOBER 1997 The Discontinuous Conduction Mode Sepic and Ćuk Power Factor Preregulators: Analysis and Design Domingos Sávio Lyrio Simonetti,

More information

Novel Passive Snubber Suitable for Three-Phase Single-Stage PFC Based on an Isolated Full-Bridge Boost Topology

Novel Passive Snubber Suitable for Three-Phase Single-Stage PFC Based on an Isolated Full-Bridge Boost Topology 264 Journal of Power Electronics, Vol. 11, No. 3, May 2011 JPE 11-3-3 Novel Passive Snubber Suitable for Three-Phase Single-Stage PFC Based on an Isolated Full-Bridge Boost Topology Tao Meng, Hongqi Ben,

More information

GENERALLY, a single-inductor, single-switch boost

GENERALLY, a single-inductor, single-switch boost IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 19, NO. 1, JANUARY 2004 169 New Two-Inductor Boost Converter With Auxiliary Transformer Yungtaek Jang, Senior Member, IEEE, Milan M. Jovanović, Fellow, IEEE

More information

An Improved T-Z Source Inverter for the Renewable Energy Application

An Improved T-Z Source Inverter for the Renewable Energy Application IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 9, Issue 2 Ver. I (Mar Apr. 2014), PP 33-40 An Improved T-Z Source Inverter for the Renewable

More information

IN A CONTINUING effort to decrease power consumption

IN A CONTINUING effort to decrease power consumption 184 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 1, JANUARY 1999 Forward-Flyback Converter with Current-Doubler Rectifier: Analysis, Design, and Evaluation Results Laszlo Huber, Member, IEEE, and

More information

ISSN (Print) : Santhi Mary Antony A / International Journal of Engineering and Technology (IJET)

ISSN (Print) : Santhi Mary Antony A / International Journal of Engineering and Technology (IJET) PERFORMANCE COMPARISON OF LLCC RESONANT BASED MULTI OUTPUT CONVERTER AND SINGLE INDUCTOR BOOST BASED MULTI OUTPUT CONVERTER FOR LED DRIVER APPLICATIONS Santhi Mary Antony A Assistant Professor, Department

More information

Simulation of AC-DC Converter for High Power Application

Simulation of AC-DC Converter for High Power Application International Journal of Power Electronics and Drive System (IJPEDS) Vol. 9, No. 1, March 2018, pp. 336~344 ISSN: 2088-8694, DOI: 10.11591/ijpeds.v9n1.pp336-344 336 Simulation of AC-DC Converter for High

More information

3SSC AND 5VMC BASED DC-DC CONVERTER FOR NON ISOLATED HIGH VOLTAGE GAIN

3SSC AND 5VMC BASED DC-DC CONVERTER FOR NON ISOLATED HIGH VOLTAGE GAIN 3SSC AND 5VMC BASED DC-DC CONVERTER FOR NON ISOLATED HIGH VOLTAGE GAIN R.Karuppasamy 1, M.Devabrinda 2 1. Student, M.E PED, Easwari engineering college.email:rksamy.3@gmail.com. 2. Assistant Professor

More information

Advanced Single-Stage Power Factor Correction Techniques

Advanced Single-Stage Power Factor Correction Techniques Advanced Single-Stage Power Factor Correction Techniques by Jinrong Qian Dissertation submitted to the faulty of the Virginia Polytechnic Institute and State University in partial fulfillment of the requirements

More information

Soft-Switching Two-Switch Resonant Ac-Dc Converter

Soft-Switching Two-Switch Resonant Ac-Dc Converter Soft-Switching Two-Switch Resonant Ac-Dc Converter Aqulin Ouseph 1, Prof. Kiran Boby 2,, Prof. Dinto Mathew 3 1 PG Scholar,Department of Electrical and Electronics Engineering, Mar Athanasius College of

More information

Controlled Transformerless Step-Down Single Stage AC/ DC Converter

Controlled Transformerless Step-Down Single Stage AC/ DC Converter Controlled Transformerless Step-Down Single Stage AC/ DC Converter K. E. Shaharban M Tech Scholar Department of Electrical Engineering FISAT,Angamaly, kerala,india Muhammed Noufal Assistant Professor Department

More information

Comparison Between CCM Single-Stage And Two-Stage Boost PFC Converters *

Comparison Between CCM Single-Stage And Two-Stage Boost PFC Converters * Comparison Between CCM Single-Stage And Two-Stage Boost PFC Converters * Jindong Zhang 1, Milan M. Jovanoviü, and Fred C. Lee 1 1 Center for Power Electronics Systems The Bradley Department of Electrical

More information

Review of Current Sharing Techniques In LED Drivers

Review of Current Sharing Techniques In LED Drivers November 10-13, 2013, Vienna, Austria Review of Current Sharing Techniques In LED Drivers Presented by: Xiaohui QU Southeast University, Nanjing, CHINA 2013/11/26 1 LED Strings in Parallel V O i i 1 2

More information

IEEE Transactions On Circuits And Systems Ii: Express Briefs, 2007, v. 54 n. 12, p

IEEE Transactions On Circuits And Systems Ii: Express Briefs, 2007, v. 54 n. 12, p Title A new switched-capacitor boost-multilevel inverter using partial charging Author(s) Chan, MSW; Chau, KT Citation IEEE Transactions On Circuits And Systems Ii: Express Briefs, 2007, v. 54 n. 12, p.

More information

ANALYSIS OF POWER QUALITY IMPROVEMENT OF BLDC MOTOR DRIVE USING CUK CONVERTER OPERATING IN DISCONTINUOUS CONDUCTION MODE

ANALYSIS OF POWER QUALITY IMPROVEMENT OF BLDC MOTOR DRIVE USING CUK CONVERTER OPERATING IN DISCONTINUOUS CONDUCTION MODE ANALYSIS OF POWER QUALITY IMPROVEMENT OF BLDC MOTOR DRIVE USING CUK CONVERTER OPERATING IN DISCONTINUOUS CONDUCTION MODE Bhushan P. Mokal 1, Dr. K. Vadirajacharya 2 1,2 Department of Electrical Engineering,Dr.

More information

PARALLELING of converter power stages is a wellknown

PARALLELING of converter power stages is a wellknown 690 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 4, JULY 1998 Analysis and Evaluation of Interleaving Techniques in Forward Converters Michael T. Zhang, Member, IEEE, Milan M. Jovanović, Senior

More information

International Journal of Engineering Research and General Science Volume 3, Issue 4, July-August, 2015 ISSN

International Journal of Engineering Research and General Science Volume 3, Issue 4, July-August, 2015 ISSN A High-Performance Single-Phase Bridgeless Interleaved PFC Converter with Over - Current Protection Edwin Basil Lal 1, Bos Mathew Jos 2,Leena Thomas 3 P.G Student 1, edwinbasil@gmail.com, 9746710546 Abstract-

More information

Neuro Fuzzy Control Single Stage Single Phase AC-DC Converter for High Power factor

Neuro Fuzzy Control Single Stage Single Phase AC-DC Converter for High Power factor Neuro Fuzzy Control Single Stage Single Phase AC-DC Converter for High Power factor S. Lakshmi Devi M.Tech(PE),Department of EEE, Prakasam Engineering College,Kandukur,A.P K. Sudheer Assoc. Professor,

More information

Keywords: Forward Boost Converter, SMPS, Power Factor Correction, Power Quality, Efficiency.

Keywords: Forward Boost Converter, SMPS, Power Factor Correction, Power Quality, Efficiency. www.semargroups.org, www.ijsetr.com ISSN 2319-8885 Vol.02,Issue.19, December-2013, Pages:2243-2247 Power Quality Improvement in Multi-Output Forward Boost Converter NARLA KOTESWARI 1, V. MADHUSUDHAN REDDY

More information

TYPICALLY, a two-stage microinverter includes (a) the

TYPICALLY, a two-stage microinverter includes (a) the 3688 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 33, NO. 5, MAY 2018 Letters Reconfigurable LLC Topology With Squeezed Frequency Span for High-Voltage Bus-Based Photovoltaic Systems Ming Shang, Haoyu

More information

Multiple Output Converter Based On Modified Dickson Charge PumpVoltage Multiplier

Multiple Output Converter Based On Modified Dickson Charge PumpVoltage Multiplier Multiple Output Converter Based On Modified Dickson Charge PumpVoltage Multiplier Thasleena Mariyam P 1, Eldhose K.A 2, Prof. Thomas P Rajan 3, Rani Thomas 4 1,2 Post Graduate student, Dept. of EEE,Mar

More information

THE HARMONIC content of the line current drawn from

THE HARMONIC content of the line current drawn from 476 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY 1998 Single-Stage Single-Switch Input-Current-Shaping Technique with Fast-Output-Voltage Regulation Laszlo Huber, Member, IEEE, and Milan

More information

A THREE-PHASE HIGH POWER FACTOR TWO-SWITCH BUCK- TYPE CONVERTER

A THREE-PHASE HIGH POWER FACTOR TWO-SWITCH BUCK- TYPE CONVERTER A THREE-PHASE HIGH POWER FACTOR TWO-SWITCH BUCK- TYPE CONVERTER SEEMA.V. 1 & PRADEEP RAO. J 2 1,2 Electrical and Electronics, The Oxford College of Engineering, Bangalore-68, India Email:Seema.aish1@gmail.com

More information

IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 4, JULY

IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 4, JULY IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 4, JULY 2008 1649 Open-Loop Control Methods for Interleaved DCM/CCM Boundary Boost PFC Converters Laszlo Huber, Member, IEEE, Brian T. Irving, and Milan

More information

A Photovoltaic Based Dual Output SEPIC- Cuk Converter for Led Driver Applications

A Photovoltaic Based Dual Output SEPIC- Cuk Converter for Led Driver Applications A Photovoltaic Based Dual Output SEPIC- Cuk Converter for Led Driver Applications P.Kolanginathan Department of Electrical and Electronics Engineering, Anna University Regional Campus, Coimbatore, India.

More information

A Novel High-Performance Utility-Interactive Photovoltaic Inverter System

A Novel High-Performance Utility-Interactive Photovoltaic Inverter System 704 IEEE TRANSACTIONS ON POWER ELECTRONICS, OL. 18, NO. 2, MARCH 2003 A Novel High-Performance Utility-Interactive Photovoltaic Inverter System Toshihisa Shimizu, Senior Member, IEEE, Osamu Hashimoto,

More information