Phone: Fax: Web: -

Transcription

1 Timer - Delay-on-Make TDM / TDMH / TDML Series Relay contacts are isolated. The TDM Series is a delay-on-make timer that combines accurate digital circuitry with isolated, DPDT relay contacts in an industry standard 8-pin plug-in package. DIP switch adjustment allows precise selection of the time delay over the full time delay range. The TDM Series is the product of choice for custom control panel and OEM designers. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 8 for dimensional drawing. Digi-Set Binary Switch Operation: Switch settable time delay Three time ranges from 0.1s - 10,230s ±0.1% repeat accuracy ±2% setting accuracy 10A, DPDT output contacts LED indication Panel mount kit: P/N: BZ1 8-pin socket: P/N: NDS-8 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) Octal socket for UL listing: P/N: P TDM120AL TDM12DL TDM230AL TDM24AL TDM24DL TDMH120AL TDMH24AL 8-pin models UL listed when used in combination with P socket only. TDMH24DL TDM10DL TDM20AL TDM2DL TDML230AL TDML24DL TDM s in 1s increments TDMH ,230s in 10s increments TDML s in 0.1s increments Voltage 12D - 12VDC 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC Type....Digital integrated circuitry Range* s in 0.1s increments s in 1s increments 10-10,230s in 10s increments Repeat Accuracy....±0.1% or 20ms, whichever is greater Setting Accuracy....±2% or 50ms, whichever is greater Reset Time ms Recycle Time....During Timing - TDMH: 500ms TDM, TDML: 300ms vs Temp. & Voltage....±2% Indicator....LED glows during timing; relay is de-energized Voltage , 24, or 110 VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VAC/DC to 230VAC % - 10% AC Line Frequency....50/60 Hz Power Consumption W Type....Electromechanical relay Form....DPDT LED Indication L Rating....10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x10 7 ; Electrical - 1 x 10 6 Polarity....DC units are reverse polarity protected Isolation Voltage V RMS input to output Mounting....Plug-in socket Dimensions x 2.39 x 1.78 in. (81.3 x 60.7 x 45.2 mm) Termination....Octal 8-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g) *For CE approved applications, power must be removed from the unit when a switch position is changed.

2 Timer - Delay-on-Make TRM Series 8-pin octal DPDT The TRM Series is a combination of analog electronic circuitry and electromechanical relay output. It provides input to output isolation with a wide variety of input voltages and time ranges. Standard plug-in base wiring, fast reset, rugged enclosure, and good repeat accuracy make the TRM a select choice in any OEM application. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 9 for dimensional drawing. 10A, DPDT or SPDT output contacts 24 to 230V operation in ranges 8-pin or 11-pin plug-in Fixed or adjustable delays from s in multiple ranges ±2% repeat accuracy Octal socket for UL listing: P/N: P Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) P/N: PSC11 (NDS-11) 8-pin socket: P/N: NDS-8 11-pin socket: P/N: NDS-11 Panel mount kit: P/N: BZ1 External adjust potentiometer: P/N: P1004- P/N: P External P/N Selection Table 8-pin models UL listed when used in combination with P socket only. 8-pin octal SPDT 11-pin DPDT Value 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm Part Number P P P P P P P P P P Relay contacts are isolated. TRM Voltage 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC and Form, Octal, DPDT 2 - Knob Adjust, Octal, DPDT 3 - Lock Shaft Adjust, Octal, DPDT 5 - Ext. Adjust, 11-pin, DPDT without potentiometer 6 - Ext. Adjust, 11-pin, DPDT supplied with potentiometer 8 - Ext. Adjust, Octal, SPDT, without potentiometer 9 - Ext. Adjust, Octal, SPDT, with potentiometer Time Tolerance - ±20% Y - ±10% Z - ±5% * (seconds) TRM110D1Z30 TRM120A21 TRM120A230 TRM120A2Y *If fixed delay is selected, insert delay ( ) in seconds. TRM120A2Y60 TRM120A2Y600 TRM24A8Y5 TRM24D1Y1 Type... Analog circuitry Range... 50ms - 10m in 15 adjustable ranges or fixed Repeat Accuracy... ±2% or 20 ms, whichever is greater Fixed Time Tolerance & Setting Accuracy... ±5, 10, or 20% Reset Time... 50ms Recycle Time... After timing: 20ms During timing: 0.1% of max. time delay or 75ms, whichever is greater vs Temp. & Voltage... ±10% Voltage or 110VDC; 24, 120, or 230VAC Type... Electromechanical relay Form... Isolated DPDT or SPDT Rating... 10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Isolation Voltage V RMS between input & output terminals Insulation Resistance MΩ Polarity... DC units are reverse polarity protected Mounting... Plug-in socket Tolerance 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% Dimensions x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Termination... Octal 8-pin or 11-pin plug-in AC Line Frequency... 50/60 Hz Power Consumption W Operating / Storage Temperature to 65 C / -30 to 85 C Weight... 6 oz (170 g)

3 Timer - Delay-on-Make The PRLM Series is designed for use in non-critical timing applications. It offers low cost, knob adjustable timing control, full 10A relay output, and onboard LED indication. The knob adjustment provides a guaranteed time range of up to 10 minutes in 6 ranges. The onboard LED indicates whether or not the unit is timing (flashing LED) as well as the status of the output. Operation (Delay-on-Make): The time delay is initiated when input voltage is applied. LED flashes during timing. At the end of the delay period, the output contacts energize. LED is on steady after the unit times out. Reset: Reset is accomplished by removal of input voltage. There is no false output when reset during timing. PRLM Series Knob adjustable time delay relay Electronic circuit with electromechanical relay Popular AC & DC operating voltages Industry standard octal plug-in connection Fixed or adjustable delays from s in multiple ranges ±2% repeat accuracy ±10% factory calibration LED indication 10A, DPDT output contacts Isolated relay contacts Appendix B, page 165, Figure 9 for dimensional drawing. Panel mount kit: P/N: BZ1 8-pin socket: P/N: NDS-8 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) 8-pin octal DPDT PRLM41180 PRLM423 PRLM Voltage 1-12VDC 3-24VDC 5-110VDC 1 - Factory Fixed 2 - Adjustable * s s s s s s Type.... Analog circuitry Range s in 6 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance.... Knob adjust: guaranteed range Fixed: ±10% Reset Time ms Recycle Time.... After timing: 20ms During timing: 0.1% of max. time delay or 75ms, whichever is greater vs Temp. & Voltage.... ±10% Voltage , 24, or 110VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 240VAC/DC % - 10% AC Line Frequency /60 Hz Power Consumption W Type.... Electromechanical relay Form.... Isolated, DPDT *If fixed delay is selected, insert delay ( ) in seconds. Rating A 28VDC; 10A 240VAC; 1/3 120/240VAC Life x10 7 ; Electrical - 1x10 6 Surge.... IEEE C Level A Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Indication Type.... LED Operation.... During timing - flashing energized - on steady Mounting.... Plug-in socket Dimensions x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Termination.... Octal 8-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g)

4 Timer - Delay-on-Make The HRDM Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230V operation in five ranges and factory fixed, onboard, or external adjustable time delays with a repeat accuracy of ±0.5%. The output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. This series is ideal for OEM applications where cost is a factor. HRDM Series 30A, SPDT, NO output contact 12 to 230V operation in 5 ranges Encapsulated circuitry Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy Factory fixed, onboard or external adjust Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 2 for dimensional drawing. External Resistance vs. : - P/N: P (AWG 10/12) NO = Normally Open L = Load C = Common, Transfer Contact NOTE: A knob, or terminals 4 & 5 are only included on adjustable units. RT is used when external adjustment is ordered. Relay contacts are not isolated. HRDM114S HRDM120 HRDM220 HRDM221 HRDM222 HRDM223 HRDM224 HRDM3112S HRDM320 HRDM321 HRDM322 HRDM323 HRDM324 HRDM4130S HRDM413M HRDM415M HRDM420 HRDM421 HRDM422 HRDM423 HRDM Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Time Tolerance Blank - ±5% A - ±1% Type.... Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration).... ±1%, ±5% Reset Time ms vs Temp. & Voltage.... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% AC Line Frequency /60 Hz Power Consumption.... AC 4VA; DC 2W Type.... Electromechanical relay Form.... Non-isolated, SPDT Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** * *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) m (M) min. Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge.... IEEE C Level A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g)

5 Timer - Delay-on-Make ERDM Series A knob, or terminals 9 & 10 are only included on adjustable units. Relay contacts are isolated. is used when external adjustment is ordered. Econo-Timers are a combination of digital electronics and a reliable electromechanical relay. These devices offer a DPDT relay output for relay logic circuits, and isolation of input to output voltages. Cost effective for OEM applications, such as random starting, sequencing ON, switch debouncing, anti-short cycling, and other common delay-on-make applications. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 10 for dimensional drawing. Factory fixed, onboard or external adjust Delays from 0.1s m ±0.5% repeat accuracy Encapsulated, digital circuitry Isolated, 10A, DPDT output contacts P/N: P P/N: P ERDM1110S ERDM123 ERDM126 ERDM128 ERDM222 ERDM310.5S ERDM324 ERDM326 ERDM4110S ERDM4130S ERDM4210 ERDM422 ERDM423 ERDM425 ERDM427 ERDM429 ERDM6210 ERDM628 ERDM629 ERDM Voltage 1-12VDC 3-24VDC 5-120VDC 2 - Onboard knob 3 - External adjust * s s s s s s Type....Digital integrated circuitry Range s - 500m in 11 adjustable ranges or 0.1s m fixed....fixed, onboard or external adjust Repeat Accuracy....±0.5% Tolerance (Factory Calibration).... ±10% Recycle Time ms vs Temp. & Voltage.... ±2% Voltage , 24, or 120VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 120VAC/DC & 230VAC % - 10% AC Line Frequency....50/60 Hz Type....Isolated relay contacts m m m m m *If fixed delay is selected, insert delay ( ) followed by (S) sec or (M) min. Form....DPDT Rating....10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Full Load - 1 x 10 6 Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with two #6 (M3.5 x 0.6) screws Dimensions x 2.5 x 1.7 in. (88.9 x 63.5 x 43.2 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -40 to 85 C Weight oz (162 g)

6 Timer - Delay-on-Make ORM Series The ORM Series features open PC board construction for reduced cost. It has isolated, 10A, DPDT relay contacts and all connections are 0.25 in (6.35 mm) male quick connect terminals. The time delay may be ordered as factory fixed, onboard knob, or external adjustment. Time delays from seconds. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 11 for dimensional drawing. Time delays from 0.05s - 300s in 5 ranges or fixed Low cost open PCB construction 10A, DPDT output contacts ±2% repeat accuracy ±10% factory calibration Factory fixed, onboard or external adjust P/N: P P/N: P ORM120A110 ORM120A115 ORM120A145 ORM120A17 ORM120A25 ORM230A17 ORM24D13.5 is used when external adjustment is ordered. Relay contacts are isolated. ORM Voltage 24A - 24VAC 24D - 24VAC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC 2 - Onboard knob 3 - External adjust Type....Analog circuitry Range s in 5 adjustable ranges or fixed Repeat Accuracy....±2% or 20ms, whichever is greater Tolerance....Adjustable: guaranteed range Fixed: ±10% Recycle Time....After timing - 16ms; During timing - 0.1% of max. time delay or 75ms, whichever is greater vs Temp. & Voltage.... ±10% Voltage or 110VDC; 24, 120, or 230VAC Tolerance 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency....50/60 Hz Power Consumption W * s s s s s *If fixed delay is selected, insert delay ( ) in seconds. Type....Electromechanical relay Form....DPDT, Isolated Rating....10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x10 7 ; Electrical - 1x10 6 Polarity....DC units are reverse polarity protected Isolation Voltage V RMS input to output Mounting....Surface mount with four #6 (M3.5 x 0.6) screws Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (77 g)

7 Timer - Delay-on-Make KRDM Series V = Voltage C = Common, Transfer Contact NO = Normally Open NC = Normally Closed A knob is supplied for adjustable units, or RT terminals 4 & 5 for external adjust. See external adjustment vs time delay chart. Relay contacts are isolated. The KRDM Series is a compact time delay relay measuring only 2 in. (50.8 mm) square. Its solidstate timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDM Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs : Compact time delay relay 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s - 100m in 5 ranges or fixed ±0.5% repeat accuracy ±5% factory calibration voltages from 12 to 230V in 6 ranges - P/N: P (AWG 10/12) KRDM110.4S KRDM110.5S KRDM111.5S KRDM1110S KRDM111S KRDM1130S KRDM120 KRDM121 KRDM2110M KRDM215M KRDM220 KRDM221 KRDM222 KRDM223 KRDM224 KRDM234 KRDM310.2S KRDM320 KRDM4110S KRDM4145S KRDM4160S KRDM421 KRDM430 KRDM433 KRDM623 Current/Ambient Temperature: KRDM Voltage 1-12VDC /DC 3-24VDC 5-110VDC 2 - Onboard knob 3 - External adjust * m *If fixed delay is selected, insert delay ( ) followed by (S) sec. or ( ) (M) min. Max. Switching Voltage...250VAC Range...0.1s - 100m in 5 adjustable ranges or fixed Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Repeat Accuracy...±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration)... ±5% Recycle Time ms vs Temp. & Voltage... ±5% Voltage , 24 or 110VDC; 24, 120 or 230VAC Circuitry...Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity...DC units are reverse polarity protected Tolerance 12VDC & 24VAC/DC...-15% - 20% 110VDC 120 & 230VAC...-20% - 10% Mounting...Surface mount with one #10 (M5 x 0.8) screw Dimensions...2 x 2 x 1.21 in (50.8 x 50.8 x 30.7 mm) AC Line Frequency / DC Ripple...50/60 Hz / 10% Power Consumption...AC 2VA; DC 2W Type...Isolated relay contacts Form...SPDT Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity...95% relative, non-condensing Weight oz (74 g) Rating (at 40 C)...10A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC

8 Timer - Delay-on-Make KSDU/ TDU Series The TDU and KSDU Series are encapsulated solidstate, delay-on-make timers that combine digital timing circuitry with universal voltage operation. The TDU offers DIP switch adjustment allowing accurate selection of the time delay over the full time delay range. The KSDU is factory fixed from 0.1s to 10,230s and does not include the DIP switch. These series are excellent choices for process control systems and OEM equipment. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. 2 universal voltage ranges from 24 to 240VAC/DC Digital integrated circuitry Switch selectable delays from 0.1s - 2.8h in 3 ranges or factory fixed ±0.5% repeat accuracy 1A steady, 10A inrush Totally solid state & encapsulated Digi-Set Binary Switch Operation: KSDU8110 KSDU TDU3000A TDU3001A TDU3003A TDUH3000A TDUH3001A TDUL3000A TDUL3001A Load may be connected to terminal 3 or 1. TDU has DIP switch adjustment; KSDU is fixed. Order Tables: KSDU Voltage Range 8-24 to 120VAC/DC to 240VAC/DC Type (Seconds) Specify fixed delay in seconds TDU Voltage Range 24 to 120VAC/DC 100 to 240VAC/DC 24 to 120VAC/DC 100 to 240VAC/DC 120 to 277VAC 24 to 120VAC/DC 100 to 240VAC/DC Time Range - Seconds Part Number TDUL3000A TDUL3001A TDU3000A TDU3001A TDU3003A TDUH3000A TDUH3001A Type...Digital integrated circuitry Range* Adjustable (TDU) s in 0.1s increments s in 1s increments s in 10s increments Fixed (KSDU)...Fixed from 0.1s s Repeat Accuracy...±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration)...±10% Recycle Time ms vs Temp. & Voltage...±5% Voltage...24 to 120VAC/DC; 100 to 240VAC/DC AC Line Frequency...50/60 Hz Tolerance...±20% Type...Solid state Form...NO, open during timing Maximum Load Current...1A steady state, 10A inrush at 60 C Minimum Holding Current....40mA Voltage Drop.... 1A Circuitry Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g) * For CE approved applications, power must be removed from the unit when a switch position is changed.

9 Timer - Delay-on-Make TMV8000 / TSU2000 Series The TMV and TSU Series are universal voltage delay-on-make timers. Two models cover all the popular voltages and time delays. Available with knob or external adjust time delay. Its simple two terminals can easily be connected in series with a relay coil, contactor coil, solenoid, lamps, small motor, etc., to delay their energization, prevent short cycling or to sequence on various loads. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Operates from 24 to 240VAC/DC Onboard or external adjust time delays Delays from 5s - 8m Totally solid state & encapsulated 1A steady, 10A inrush Two terminal series connection with load P/N: P P/N: P TMV8000 TSU2000 Load may be connected to terminal 3 or 1. TMV has knob adjustment. TSU has external adjustment terminals 4 & 5. Voltage Range 24 to 240VAC/DC 24 to 240VAC/DC 5-480s 0.1-8m External Onboard Part Number TSU2000 TMV8000 Type.... Analog circuitry Range s (TSU2000) 0.1-8m (TMV8000) Repeat Accuracy.... ±2% Tolerance (Factory Calibration).... ±10% Reset Time ms Voltage to 240VAC/DC ±20% AC Line Frequency /60 Hz Type.... Solid State Form.... NO, open during timing Maximum Load Current.... 1A steady state, 10A inrush at 55 C Minimum Holding Current mA Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 70 C / -30 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

10 Timer - Delay-on-Make TSD1 Series The TSD1 Series is designed for more demanding commercial and industrial applications where small size and accurate performance is required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD1 Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Fixed or adjustable delays from 0.1s - 100h ±0.1% repeat accuracy ±1% factory calibration 12 to 230V in 6 ranges 1A, solid-state output Encapsulated - Load may be connected to terminal 3 or 1. External Resistance vs. : TSD11110S TSD1311.2S TSD1315S TSD1320 TSD1321 TSD1424 TSD1 Voltage 1-12VDC 3-24VDC 5-120VDC 2 - External adjust 3 - Onboard adjust * m m h Range s - 100h in 7 adjustable ranges or fixed Repeat Accuracy....±0.1% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Recycle Time ms vs Temp. & Voltage.... ±1% Voltage , 24, 120VDC; 24, 120, 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Type....Solid state Form....NO, open during timing Maximum Load Current....1A steady state, 10A inrush at 60 C Minimum Holding Current mA Off State Leakage Current VAC Voltage Drop.... 1A *If fixed delay is selected, insert delay ( ) followed by (S) sec. (M) min. or (1-100) (H) hours. Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

11 Timer - Delay-on-Make THDM Series The THDM Series is a high power solid-state delay-on-make timer that is connected in series with the load. The THDM eliminates the need for a timer and a separate solid-state relay. A cost effective approach for controlling larger loads, such as motors, electric heating elements, and lamps. When mounted on a metal surface, it can switch loads up to 20A steady, 200A inrush. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output is energized and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 4 for dimensional drawing. High load currents up to 20A, 200A inrush Simple-to-use two terminal series connection ± 0.5% repeat accuracy Fixed or adjustable delays from 1s m ± 10% factory calibration 24, 120, or 230VAC Metallized mounting surface for heat transfer Solid state & encapsulated P/N: P P/N: P P/N: P (AWG 10/12) Plug-on adjustment module: P/N: VTP()() Load may be connected to terminal 3 or s s m m m VTP P/N VTP5G VTP5K VTP5N VTP5P VTP5R Selection Table for VTP Plug-on Accessory. There are no part numbers currently active. Please call Technical Support with your requirements. THDM Voltage 2 - External adjust * m m Type.... Digital intergrated circuitry Range.... 1s m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 10% Recycle Time.... After timing - 350ms; During timing - 150ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Type.... Solid state Form.... NO, open during timing Maximum Load Currents Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A Rating A - 6A B - 10A C - 20A *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (1-100) (M) min. Minimum Load Current mA Effective Voltage Drop (V Line - V Load) Effective Drop 24VAC 3V 120VAC 3V 230VAC 5V Circuitry... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **... Surface mount with one #10 (M5 x 0.8) screw Dimensions... 2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity... 95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

12 Timer - Delay-on-Make The THD1 Series combines accurate timing circuitry with high power solid-state switching. It can switch motors, lamps, and heaters directly without a contactor. You can reduce labor, component cost, and increase reliability with these small, easy-to-use, Digi-Power timers. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 4 for dimensional drawing. External Resistance vs. : THD1 Series High load currents up to 20A, 200A inrush Fixed or adjustable delays from 0.1s m ±0.5% repeat accuracy ±1% factory calibration 24, 120, or 230VAC Metallized mounting surface for heat transfer Totally solid state & encapsulated - P/N: P (AWG 10/12) THD1B410.5S THD1C231 THD1C232 THD1C233 THD1C234 THD1C235 THD1C415M THD1C431 THD1C432 THD1C433 THD1C434 THD1C435 THD1C6110S S1 = Optional Low Current Initiate Switch is used when external adjustment is ordered. THD1 Rating A - 6A B - 10A C - 20A Voltage 2 - External adjust 3 - Onboard adjust Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Recycle Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance.... ±20% Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, open during timing Maximum Load Current Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A * m m *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Minimum Load Current mA Voltage Drop.... rated current OFF State Leakage Current VAC Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

13 Timer - Delay-on-Make KSD1 Series Load may be connected to terminal 3 or 1. The KSD1 Series features two-terminal, seriesconnection with the load. The KSD1 Series is an ideal choice for delay-on-make timing applications. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid-state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for popular AC and DC voltages. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Fixed or adjustable delays from 0.1s m in 6 ranges ±0.5% repeat accuracy ±5% factory calibration 12 to 230V in 5 options 1A, solid-state output Encapsulated - P/N: P (AWG 18/22) KSD11120S KSD1122 KSD1123 KSD1133 KSD1230 KSD13110M KSD1320 KSD1412S KSD14130S KSD1420 KSD1431 KSD16130S KSD1 Voltage 1-12VDC 3-24VDC 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Recycle Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC; 12 or 24VDC Tolerance.... ±20% AC Line Frequency /60 Hz Type.... Solid state Form.... NO, open during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C Minimum Holding Current mA OFF State Leakage Current VAC *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

14 Timer - Delay-on-Make TS1 Series Versa-Timer offers proven reliability and performance with years of use in OEM equipment and commercial applications. This encapsulated general use timing module is capable of controlling load currents ranging from 5mA to 1A. May be connected in series with contactors, relays, valves, solenoids, small motors, and lamps. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Two terminal series connection with load 5mA - 1A load currents Totally solid state & encapsulated ±2% repeat accuracy Fixed or adjustable delays from 0.05s - 10m in 8 ranges P/N: P1004- P/N: P Plug-on adjustment module: P/N: VTP()() Selection Table for VTP Plug-on Accessory. Load may be connected to terminal 3 or 1. TS1 Voltage 1-12VDC 3-24VDC 5-120VDC 2 - External adjust Type... Analog circuitry Range * (12VDC) s s s s 12VDC s in 4 adjustable ranges or fixed (1 MΩ max. ) Other Voltages s in 4 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±10% Recycle Time.... After timing 16ms During timing 0.1% of time delay or 75ms, whichever is greater vs Temp. & Voltage.... ±10% Voltage , 24 or 120VDC; 24, 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Type.... Solid state * (ALL other voltages) s s s s All Other Voltages s s s s TS1111 TS12110 TS TS12120 TS12130 TS TS1214 TS TS12160 TS12190 TS1221 TS1222 TS1224 TS13115 TS1321 TS TS *If fixed delay is selected, insert delay ( ) (12VDC) or ( ) (other voltages) in secs. VTP P/N VTP4B VTP4F VTP4J VTP5N s s s s 12VDC TS1411 TS14110 TS TS1412 TS14120 TS14130 TS1415 TS1416 TS1418 TS1421 TS1422 TS1423 TS1424 TS1612 TS1615 TS1621 TS1622 VTP P/N VTP2A VTP2E VTP2F VTP2H Form.... NO, open during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C Minimum Holding Current.... 5mA Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 80 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

15 Timer - Delay-on-Make TH1 Series The TH1 Series is a solid-state relay and timer combined into one compact, easy-to-use control. This highly reliable device eliminates the need for a separate solid-state relay. When mounted to a metal surface, it can switch load currents up to 20A steady state, and 200A inrush. Operation (Delay-on-Make): Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. High current load capacity up to 20A with 200A inrush Solid-state switching - no contact wear or arcing Encapsulated Fixed or adjustable time delays from s ± 2% repeat accuracy ± 5% factory calibration Metallized mounting surface for heat transfer Appendix B, page 165, Figure 4 for dimensional drawing. - P/N: P (AWG 10/12) TH1A421 TH1B633 TH1C415 TH1C621 S1 = Optional Low Current Initiate Switch TH1 Rating A - 6A B - 10A C - 20A Voltage 2 - External adjust 3 - Onboard adjust Range s in 4 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 5% vs Temp. & Voltage.... ±10% Recycle Time ms Voltage , 120, or 230VAC Tolerance.... ±15% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, open during timing Maximum Load Currents Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A * s s s s *If fixed delay is selected, insert delay ( ) in secs. Minimum Load Current mA Voltage Drop V at rated current OFF State Leakage Current VAC Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

16 Timer - Delay-on-Make MSM Series The MSM replaces bi-metal type timing with reliable solid-state circuitry. There are no moving parts to arc or wear. It is a cost effective solution for OEM designers. It is available for printed circuit board mounting or surface mounting with a removable bracket and wire leads. The MSM offers immediate reset on removal of power. Operation (Delay-on-Make): The time delay begins upon application of input voltage. The output is de-energized before and during the time delay. At the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 167, Figure 25 for dimensional drawing. Printed circuit mount or wire leads Fixed delays from s ± 5% repeat accuracy ± 15% factory calibration Two-wire series connection with the load Fast reset MSM10.2W7 MSM10.5W6 MSM10.7W6 MSM11W6 MSM110W6 MSM130W9 MSM16W9 MSM190W6 MSM20.15W9 MSM210P3 MSM21W9 MSM22W6 MSM25W9 MSM30.7W6 MSM33W9 MSM360P1 MSM40.2W6 MSM420W6 MSM42W6 MSM610W9 V = Voltage L = Load R = Red Wire B = Black Wire MSM Voltage 1-12VDC 3-24VDC Fixed s Specify fixed time in seconds. Wire Type P - PC Mount W - Stranded Wire Leads Type.... Analog Circuitry Range s fixed Repeat Accuracy.... ±5% Tolerance (Factory Calibration).... ±15% Recycle Time ms vs Temp. & Voltage.... ±15% Voltage or 24VDC; 24, 120, or 230VAC Tolerance.... ±10% AC Line Frequency /60 Hz Type.... Solid State Form.... NO, open during timing Maximum Load Current A steady state 25 C; 0.25A steady state 60 C Minimum Holding Current... 40mA Wire Length Inches (mm) (6.35) (9.53) (12.70) (15.88) (19.05) (152.4) (177.8) (203.2) (228.6) Voltage Drop A Circuitry.... Encapsulated Dielectric Breakdown V RMS input to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... a. PC mount 14 AWG (2.087mm 2 ) wires (Can be inserted in AMP Miniature Spring Socket # ) b. Stranded 18 AWG wire leads (0.933 mm 2 ) with mounting bracket Operation / Storage Temperature to 60 C / -30 to 85 C Humidity % relative, non-condensing Weight.... P: 1.1 oz (31.2 g) W: 1.2 oz (34 g)

17 Timer - Delay-on-Make TSD4 Series The TSD4 Digi-Timer is a delay-on-make timer with a normally closed solid-state output. The load is energized prior to and during the delay period. The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance are required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Make NC): Upon application of input voltage, the load energizes immediately. When the initiate switch is closed, the time delay begins. At the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load energizes again and the time delay is reset. Removing input voltage resets the time delay. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Fixed or adjustable delays from 0.1s - 100h 24, 120, or 230VAC ±0.1% repeat accuracy ±1% factory calibration 1A, solid-state output Encapsulated - TSD44115S S1 = Initiate Switch TSD4 Voltage 2 - External adjust 3 - Onboard adjust Range s - 100h in 7 adjustable ranges or fixed Repeat Accuracy.... ±0.1% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms vs Temp. & Voltage.... ±1% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NC, closed before & during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C OFF State Leakage Current VAC * m *If fixed delay is selected, insert m delay ( ) followed by (S) sec h (M) min. or (1-100) (H) hours. Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

18 Timer - Delay-on-Make THD4 Series The THD4 utilizes solid-state circuitry and a solid-state relay in one easy to use control. The metallized mounting surface allows a metal panel to dissipate heat rather than adding an expensive heat sink. The solid-state output is rated 6, 10, or 20 amps steady and up to 200 amps inrush. Motors, heaters and valves can be switched directly, eliminating the expense of a separate contactor. The THD4 offers substantial performance, reliability, and cost advantages for OEM designers. Operation (Delay-on-Make NC): Upon application of input voltage, the load is energized immediately. When the initiate switch closes, the time delay begins. At the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load is again energized and the time delay is reset. Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 4 for dimensional drawing. High load current capacity up to 20A, 200A inrush Load energized prior to & during timing ±0.5% repeat accuracy ±1% factory calibration Totally solid state & encapsulated Fixed or adjustable delays from 0.1s m in 6 ranges - P/N: P (AWG 10/12) External Resistance vs. : There are no part numbers currently active. Please call Technical Support with your requirements. S1 = Low Current Initiate Switch THD4 Rating A - 6A B - 10A C - 20A Voltage 2 - External adjust 3 - Onboard adjust Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NC Rating Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A * m m *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Minimum Load Current mA Voltage Drop V at rated current OFF State Leakage Current VAC Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

19 Timer - Delay-on-Make KSD4 Series The KSD4 Digi-Timer offers a delay-on-make function with normally closed solid-state output. The load is energized prior to and during the time delay. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid-state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for input voltages of 24, 120 or 230VAC. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Make NC): Upon application of input voltage, the load energizes immediately. When the initiate switch is closed, the time delay begins. At the end of the time delay, the load deenergizes. Reset: When the initiate switch is reopened, the load energizes and the time delay is reset. Removing input voltage resets the time delay. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Fixed or adjustable delays from 0.1s m ±0.5% repeat accuracy ±5% factory calibration 24, 120, or 230VAC 1A, solid-state output Encapsulated - KSD4433 S1 = Initiate Switch KSD4 Voltage 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration.... ± 5% Reset Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NC, closed before & during timing Maximum Load Current....1A steady state, 10A inrush at 60 C *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. OFF State Leakage Current VAC Voltage Drop.... 1A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

20 Timer - Delay-on-Make TS4 Series The TS4 Versa-Timer is an analog delay-on-make timer with a normally closed solid-state output. Unlike an interval timer, the load is energized prior to and during the time delay period. It can be used as a faster starting interval time delay when S1 is closed upon application of input voltage. Operation (Delay-on-Make NC): Upon application of input voltage, the load is energized immediately. When the initiate switch is closed, the time delay begins. At the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load again energizes and the time delay is reset. Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Fixed or adjustable delay Load energized prior to & during time delay s in 4 ranges ±2% repeat accuracy 24, 120, or 230VAC 1A, solid-state output Encapsulated P/N: P1004- P/N: P Plug-on adjustment module: P/N: VTP()() s s s s VTP P/N VTP4B VTP4F VTP4J VTP5N S1 = Initiate Switch Selection Table for VTP Plug-on Accessory. TS TS4422 TS4611 TS4 Voltage 2 - External adjust * s s s s Type.... Analog circuitry Range s in 4 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater; under fixed conditions Tolerance (Factory Calibration).... ±10% vs Temp. & Voltage.... ±10% Recycle Time ms Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Type.... Solid state Form.... NC, closed during timing *If fixed delay is selected, insert delay ( ) in secs. Maximum Load Current.... 1A steady state, 10A inrush at 60 C Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

21 Timer - Delay-on-Break TDB / TDBH / TDBL Series 8-pin octal SPDT S1 = Initiate Switch Relay contacts are isolated. The TDB Series combines accurate digital circuitry with isolated, 10A, DPDT or SPDT contacts in an 8 or 11-pin plug-in package. The TDB Series features DIP switch selectable time delays ranging from ,230 seconds in three ranges. The TDB Series is the product of choice for custom control panel and OEM designers. Operation (Delay-on-Break): voltage must be applied to the input before and during timing. Upon closure of the initiate switch, the output relay is energized. The time delay begins when the initiate switch is opened (trailing edge triggered). The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 8 for dimensional drawing. Digi-Set Binary Switch Operation: Switch settable time delay Three time ranges from 0.1s - 10,230s ±0.1% repeat accuracy ±2% setting accuracy 10A, SPDT or DPDT output contacts LED indication Panel mount kit: P/N: BZ1 Hold-down c lips (sold i n p airs): P/N: PSC8 (NDS-8) P/N: PSC11 (NDS-11) 11-pin socket: P/N: NDS-11 Octal 8-pin socket: P/N: NDS-8 Octal socket for UL listing: P/N: P TDB120AL TDB120ALD TDB12D TDB230AL TDB24AL TDB24DL 8-pin models UL listed when used in combination with P socket only. TDBH120AL TDBH120ALD TDBH24AL TDB20AL TDB20ALD TDBL24DL 11-pin DPDT TDB s in 1s increments TDBH ,230s in 10s increments TDBL s in 0.1s increments Voltage 12D - 12VDC 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC LED* L Type....Digital integrated circuitry Range** s in 0.1s increments s in 1s increments 10-10,230s in 10s increments Repeat Accuracy....±0.1% or 20ms, whichever is greater Setting Accuracy....±2% or 50ms, whichever is greater Reset Time ms Recycle Time ms vs Temp. & Voltage....±5% Indicator....LED indicates relay is energized Initiate Time ms Voltage , 24/28, or 110VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency....50/60 Hz Power Consumption W *Note: LED not available on 12VDC units. Type Plug / Form D - 11-pin plug, DPDT Blank - Octal (8-pin) plug, SPDT Type....Electromechanical relay Form....SPDT or DPDT Rating....10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Isolation Voltage V RMS input to output Polarity....DC units reverse polarity protected Mounting....Plug-in socket Dimensions x 2.4 x 1.8 in. (81.3 x 60.7 x 45.2 mm) Termination....Octal 8-pin plug-in or 11-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g) ** For CE approved applications, power must be removed from the unit when a switch position is changed.

22 Timer - Delay-on-Break The TRB Series combines an isolated, 10A electromechanical relay output with analog timing circuitry. False trigger of the TRB by a transient is unlikely because of the complete isolation of the circuit from the line prior to initiation. The initiate contact is common to one side of the line and may be utilized to operate other loads. Installation is easy due to the TRB s industry standard 8 or 11-pin plug-in base wiring. TRB Series Onboard adjustable time delays Fixed or adjustable delays from s in multiple ranges ±2% repeat accuracy AC and DC operating voltages are available Isolated, 10A, SPDT or DPDT output contacts 8-pin octal SPDT Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output relay energizes. The time delay begins when the initiate switch is opened (trailing edge triggered). The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 9 for dimensional drawing. 8-pin models UL listed when used in combination with P socket only. Panel mount kit: P/N: BZ1 Hold-down c lips (sold i n p airs): P/N: PSC8 (NDS-8) P/N: PSC11 (NDS-11) Octal 8-pin socket: P/N: NDS-8 11-pin socket: P/N: NDS-11 Octal socket for UL listing: P/N: P External ad just potentiometers: P/N: P1004- P/N: P pin SPDT 11-pin DPDT External P/N Selection Table Value 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm Part Number P P P P P P P P P P TRB120A1Y240 TRB120A2Y1 TRB120A2Y3 TRB120A2Y30 TRB120A3600 TRB24A1Y0.2 TRB24A4Y60 TRB24D10Y10 TRB Voltage 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC S1 = Initiate Switch Relay contacts are isolated. and Form, Octal, SPDT (AC Volts only) 2 - Onboard Adjust, Octal, SPDT (AC Volts only) 3 - Lock Shaft Adjust, Octal, SPDT (AC Volts only) 4 - Onboard adjust, 11-pin, DPDT 7 - Ext. Adjust, 11-pin, SPDT without potentiometer 10 - Fixed, 11-pin, DPDT Time Tolerance - ±20% Y - ±10% Z - ±5% *If fixed delay is selected, insert delay ( ) in seconds. * (seconds) Type.... Analog circuitry Range ms - 10m in 15 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Fixed Time Tolerance & Setting Accuracy.... ±5, 10, or 20% Initiate Time ms Reset Time ms Recycle Time ms vs Temp. & Voltage.... ±10% Voltage /28 or 110VDC; 24, 120, or 230VAC (DC voltages on DPDT output models only) Tolerance 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency /60 Hz Power Consumption W Type.... Electromechanical relay Form.... Isolated SPDT or DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Insulation Resistance MΩ Isolation Voltage V RMS between input to output Polarity.... DC units are reverse polarity protected Mounting... Plug-in socket Dimensions x 2.39 x 1.78 in (91.6 x 60.7 x 45.2 mm) Termination.... Octal 8-pin plug-in or 11-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g)

23 Timer - Delay-on-Break PRLB Series The PRLB Series is designed for use on non-critical timing applications. It offers low cost, knob adjustable timing control, full 10A relay output, and onboard LED indication. The knob adjustment provides a guaranteed time range of up to 10 minutes in 6 ranges. The onboard LED indicates whether or not the unit is timing (flashing LED) as well as the status of the output. Operation (Delay-on-Break): voltage must be applied at all times prior to and during timing. Upon closure of the initiate switch, the output contacts transfer and remain transferred if no further action is taken. The LED is on steady. When the initiate switch is opened, the time delay is started. The LED flashes during timing. At the conclusion of the delay, the output contacts revert to their original unenergized position. Applying input voltage with the initiate switch closed will energize the load. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 9 for dimensional drawing. Onboard adjustable time delay relay Electronic circuit with electromechanical relay Popular AC & DC operating voltages Industry standard octal plug-in connection Time delays s in 6 ranges ±2% repeat accuracy ±10% factory calibration LED indication 10A, SPDT output contacts Panel mount kit: P/N: BZ1 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) Octal 8-pin socket: P/N: NDS-8 PRLB422 PRLB425 S1 = Initiate Switch Relay contacts are isolated. PRLB Voltage 1-12VDC 3-24VDC 5-110VDC 1 - Factory Fixed 2 - Adjustable * s s s s s s *If fixed delay is selected, insert delay ( ) in seconds. Type... Analog circuitry Range s in 6 adjustable ranges or fixed Repeat Accuracy... ±2% or 20ms, whichever is greater Tolerance... Knob adjust: guaranteed range Fixed: ±10% Reset Time... 75ms Recycle Time ms vs Temp. & Voltage... ±10% Voltage , 24, or 110VDC; 24, 120, or 230VAC Surge... IEEE C Level A Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity... DC units are reverse polarity protected Indication Type... LED Operation... energized - on steady energized & timing - flashing Mounting... Plug-in socket Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% Dimensions x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Termination... Octal 8-pin plug-in AC Line Frequency... 50/60 Hz Power Consumption W Operating / Storage Temperature to 65 C / -30 to 85 C Weight... 6 oz (170 g) Type... Electromechanical relay Form... Isolated, SPDT Rating... 10A 28VDC; 10A 240VAC; 1/3 120 & 240VAC Life x10 7 ; Electrical - 1x10 6

24 Timer - Delay-on-Break HRDB Series S1 = Initiate Switch L = Timed Load UTL = Untimed Load (optional) NO = Normally Open C = Common, Transfer Contact NOTE: A knob, or terminals 4 & 5 are only included on adjustable units. is used when external adjustment is ordered. Relay contacts are isolated. Dashed lines are internal connections. The untimed load is optional. HRDB Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Type....Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration)....±1%, ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage....±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% AC Line Frequency....50/60 Hz Power Consumption....AC 4VA; DC 2W Type....Electromechanical relay Form....Isolated, SPDT Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A The HRDB Series combines an electromechanical, relay output with microcontroller timing circuitry. The HRDB offers 12 to 230V operation in five options and factory fixed, external, or onboard adjustable time delays with a repeat accuracy of ±0.5%. The isolated output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. The HRDB is ideal for OEM applications where cost is a factor. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output relay energizes. The time delay begins when the initiate switch is opened. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 2 for dimensional drawing. External Resistance vs. : Time Tolerance Blank - ±5% A - ±1% * m Isolated, 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy Factory fixed, onboard or external adjust - P/N: P (AWG 10/12) HRDB1110M HRDB113S HRDB117S HRDB120 HRDB121 HRDB124 HRDB21A65M HRDB220 HRDB221 HRDB222 HRDB223 HRDB224 HRDB315M HRDB3160M *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) (M) min. HRDB320 HRDB321 HRDB322 HRDB323 HRDB324 HRDB4130S HRDB420 HRDB421 HRDB422 HRDB423 HRDB424 HRDB615M HRDB621 HRDB623 Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge....IEEE C Level A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....3 x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g)

25 Timer - Delay-on-Break ORB Series The ORB Series open PCB construction offers the user good economy without sacrificing performance and reliability. The output relay is available in isolated, 10A, DPDT or SPDT forms. The time delay may be ordered as factory fixed, onboard knob, or external adjustment. All connections are 0.25 in. (6.35 mm) male quick connect terminals. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output relay energizes. The time delay begins when the initiate switch is opened (trailing edge triggered). The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 11 for dimensional drawing. Low cost open PCB construction 10A, DPDT or SPDT output contacts Line voltage initiation Delays from 0.05s - 300s in 5 ranges ±2% repeat accuracy ±10% factory calibration P/N: P P/N: P ORB120A160 ORB120A25 ORB24A15D ORB24A21D ORB24A25 SPDT DPDT Relay contacts are isolated. ORB Voltage 24A - 24VAC 120A - 120VAC 230A - 230VAC 2 - Onboard knob 3 - External adjust * s s s s s Type.... Analog circuitry Range s in 5 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... Adjustable: guaranteed range Fixed: ±10% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance 24VAC % - 20% 120 & 230VAC % - 10% AC Line Frequency /60 Hz Power Consumption W Form Blank - SPDT D - DPDT *If fixed delay is selected, insert delay ( ) in seconds. Type.... Electromechanical relay Form.... Isolated, SPDT or DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x10 7 ; Electrical - 1x10 6 Isolation Voltage V RMS input to output Mounting.... Surface mount with four #6 (M3.5 x 0.6) screws Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (77 g)

26 Timer - Delay-on-Break KRDB Series V = Voltage S1 = Initiate Switch C = Common, Transfer Contact NO = Normally Open NC = Normally Closed UTL = Untimed Load (optional) A knob is supplied for adjustable units. The untimed load is optional. Relay contacts are isolated. The KRDB Series is a compact time delay relay measuring only 2 in. (50.8 mm) square. Its microcontroller timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDB Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output relay energizes. The time delay begins when the initiate switch is opened. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Compact time delay relay Microcontroller circuitry ±0.5% repeat accuracy Isolated, 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s m in 6 ranges voltages from 12 to 230V in 6 options ±5% factory calibration - P/N: P (AWG 10/12) KRDB1110S KRDB112.5S KRDB1120M KRDB115M KRDB1160M KRDB120 KRDB121 KRDB124 KRDB125 KRDB217S KRDB222 KRDB31120S KRDB415S KRDB420 KRDB421 KRDB422 KRDB424 KRDB425 Current/Ambient Temperature KRDB Voltage 1-12VDC /DC 3-24VDC 5-110VDC 2 - Onboard knob 3 - External adjust Type....Microcontroller with watchdog circuitry Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Recycle Time ms Initiate Time ms vs Temp. & Voltage.... ±5% Voltage , 24, 110VDC; 24, 120 or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC, 120 or 230VAC % - 10% AC Line Frequency / DC Ripple....50/60 Hz / 10% Power Consumption....AC 2VA; DC 2W Type....Isolated relay contacts Form....SPDT Rating (at 40 C)....10A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC * m *If fixed delay is selected, insert delay ( m ) followed by (S) sec, or (M) min. Max. Switching Voltage VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry....Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (74 g)

27 Timer - Delay-on-Break The TDUB Series combines digital timing circuitry with universal voltage operation. Voltages of 24 to 240VAC and 12 to 24VDC are available in three ranges. The TDUB Series offers DIP switch selectable time delays ranging from 0.1 seconds to minutes in three ranges. Its 1A rated output, ability to operate on multiple voltages, and wide range of switch selectable time delays make the TDUB Series an excellent choice for process control systems and OEM equipment. Switch selectable time setting 0.1s m in 3 ranges ± 0.5% repeat accuracy ± 2% setting accuracy 1A, solid-state output Wide voltage ranges TDUB Series Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output energizes. The time delay begins when the initiate switch is opened (trailing edge triggered). The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. P/N: P (AWG 10/12) P/N: P (AWG 18/22) DIN rail: P/N: C103PM DIN rail adaptor: P/N: TDUB3000A TDUB3002A TDUBH3002A TDUBL3002A UTL = Optional Untimed Load S1 = Initiate Switch L = Timed Load Add the value of switches in the ON position for the total time delay. Voltage Range 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC Time Range s s s s s s m m m Part Number TDUBL3000A TDUBL3001A TDUBL3002A TDUB3000A TDUB3001A TDUB3002A TDUBH3000A TDUBH3001A TDUBH3002A Range* s in 0.1s increments s in 1s increments m in 0.1m increments Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Setting Accuracy.... ±2% or 20ms, whichever is greater Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±5% Voltage / Tolerance to 240VAC, 12 to 24VDC /±20% AC Line Frequency / DC Ripple /60 Hz / 10% Power Consumption.... AC 2VA; DC 1W Type.... Solid state Form.... NO, closed before and during timing Rating.... 1A steady state, 10A inrush at 60 C Voltage Drop.... AC 1A; DC 1A Off State Leakage Current.... AC 230VAC; DC 1mA Circuitry Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g) *For CE approved applications, power must be removed from the unit when a switch position is changed.

28 Timer - Delay-on-Break TSDB Series (Positive Switching) (Negative Switching) The TSDB Series is designed for more demanding commercial and industrial applications where small size, and accurate performance are required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 1000 minutes are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output energizes. The time delay begins when the initiate switch is opened. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Fixed or adjustable delays 0.1s m in 6 ranges ±0.5% repeat accuracy ± 1% factory calibration 12VDC to 230VAC in 5 options 1A, solid-state output Encapsulated - TSDB120P TSDB320P TSDB420 TSDB431 TSDB434 UTL = Optional Untimed Load L = Timed Load S1 = Initiate Switch TSDB Voltage 1-12VDC 3-24VDC 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance....±15% Power Consumption....AC 2VA; DC 1W AC Line Frequency / DC Ripple....50/60 Hz / 10 % Type....Solid state Form....NO, closed before & during timing Maximum Load Current....1A steady state, 10A inrush at 60 C Switching Mode (VDC only) P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Off State Leakage Current VAC; DC 1mA Voltage Drop....AC 1A; DC 1A DC Operation....Positive or negative switching Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

29 Timer - Delay-on-Break THDB Series The THDB Series combines accurate timing circuitry with high power, solid-state switching. It can switch motors, lamps, and heaters directly without a contactor. You can reduce labor, component cost, and increase reliability with these small, easy-to-use, Digi-Power timers. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output energizes. The time delay begins when the initiate switch is opened. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output energizes if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 4 for dimensional drawing. High load currents up to 20A, 200A inrush Fixed or adjustable 0.1s m in 6 ranges ±0.5% repeat accuracy ±1% factory calibration 24, 120, or 230VAC Metallized mounting surface for heat transfer Totally solid-state & encapsulated - P/N: P (AWG 10/12) UTL = Optional Untimed Load L = Timed Load S1 = Initiate Switch External Resistance vs. : THDB231C THDB232C THDB233C THDB234C THDB235C THDB4110MC THDB421A THDB430C THDB431C THDB432C THDB433C THDB434C THDB435C THDB Voltage 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, closed before & during timing Maximum Load Current Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A Rating A - 6A B - 10A C - 20A *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Voltage Drop.... rated current Off State Leakage Current VAC Minimum Load Current mA Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

30 Timer - Delay-on-Break KSDB Series (Positive Switching) (Negative Switching) UTL = Optional Untimed Load L = Load S1 = Initiate Switch The KSDB is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid-state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for popular AC and DC voltages. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output energizes. The time delay begins when the initiate switch is opened. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output energizes if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Fixed or adjustable 0.1s m in 6 ranges ±0.5% repeat accuracy ± 5% factory calibration 12VDC to 230VAC in 6 ranges 1A, solid-state output Encapsulated - P/N: P (AWG 18/22) KSDB1110MP KSDB1115SP KSDB1120SP KSDB113MP KSDB113SP KSDB1160SP KSDB120P KSDB134P KSDB2115S KSDB220 KSDB231 KSDB312SN KSDB314SP KSDB315SP KSDB320P KSDB324N KSDB330N KSDB330P KSDB334P KSDB4110S KSDB41150S KSDB4120M KSDB4160S KSDB4190M KSDB431 KSDB61150S KSDB631 KSDB Voltage 1-12VDC 3-24VDC 5-120VDC 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage , 24, or 120VDC; 24, 120, or 230VAC Tolerance....±20% Power Consumption....AC 2VA; DC 2W AC Line Frequency / DC Ripple....50/60 Hz / 10 % Type....Solid state Form....NO, closed before & during timing Maximum Load Current....1A steady state, 10A inrush at 60 o C Switching Mode (VDC only) P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. OFF State Leakage Current....AC 230VAC; DC 1mA Voltage Drop....AC 1A; DC 1A DC Operation....Positive or negative switching Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 80 C Humidity....95% relative, non-condensing Weight oz (68 g)

31 Timer - Interval/Delay-on-Break TSD7 Series Interval The TSD7 utilizes only two terminals connected in series with the load. Interval timing mode period is achieved by using a small portion of the AC sine wave allowing sufficient voltage for circuit operation. It can be used as an interval timer to control or pulse shape the operation of contactors, solenoids, relays, and lamp loads. The TSD7 can be wired to delay on the break of a switch for energy saving fan delays. Operation (Interval): Upon application of input voltage, the output energizes and the time delay begins. The output remains energized throughout the time delay. At the end of the time delay, the output de-energizes and remains de-energized until power is removed. Reset: Removing input voltage resets the time delay and the output. Operation (Delay-on-Break): Upon closure of SW1, the load is energized and the timer is reset (zero volts across its input terminals). Opening SW1 re-applies input voltage to the timer, the load remains energized and the time delay begins. At the end of the time delay, the output de-energizes. If SW1 is open when power is applied, the load will energize for the time delay then de-energize. Reset: Reclosing SW1 resets the timer. Two terminal series connection to load Fixed or adjustable 1s m in 5 ranges Digital integrated circuitry ±0.5% repeat accuracy P/N: P P/N: P Plug-on adjustment module: P/N: VTP()() VTP P/N Appendix B, page 165, Figure 1 for dimensional drawing s s m m m VTP5G VTP5K VTP5N VTP5P VTP5R Delay-on- Break Selection Table for VTP Plug-on Accessory. V = Voltage L = Load S1 = Initiate Switch TSD72130S TSD7222 TSD74110M TSD7412S TSD7413S TSD7414M TSD7421 TSD7423 TSD7424 TSD761120S TSD761180S TSD7611S TSD7621 TSD7 Voltage 2 - External adjust Type.... Digital integrated circuitry Range.... 1s m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±10% Recycle Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Type.... Solid state Form.... NO, closed during timing Maximum Load Current.... 1A steady state, 10A inrush at 45 C Minimum Load Current mA * *If fixed delay is selected, insert m delay ( ) followed by (S) sec m or (1-1000) (M) min. Effective Voltage Drop (VLine-VLoad) Effective Drop 24VAC 3V 120VAC 4V 230VAC 6V Circuitry... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting... Surface mount with one #10 (M5 x 0.8) screw Dimensions... 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity... 95% relative, non-condensing Weight oz (68 g)

32 Timer - Interval/Delay-on-Break The THD7 utilizes only two terminals connected in series with the load. Interval timing mode is achieved by using a small portion of the AC sine wave allowing sufficient voltage for circuit operation. The THD7 can be used for interval or delay-on-break timing. It is designed to operate large loads directly, such as motors, heater elements, and motor starters. THD7 Series Solid-state relay and timer combined Two terminal series connection to load Up to 20A steady state, 200A inrush Fixed or adjustable delays from 1s m ±0.5% repeat accuracy Interval Operation (Interval): Upon application of input voltage, the output energizes and the time delay begins. The output remains energized throughout the time delay. At the end of the time delay the output de-energizes and remains de-energized until power is removed. Reset: Removing input voltage resets the time delay and the output. Operation (Delay-on-Break): Upon closure of SW1, the load energizes and the timer is reset (zero voltage across its input terminals). Opening SW1 re-applies input voltage to the timer, the load remains energized and the time delay begins. At the end of the time delay the output de-energizes. If SW1 is open when power is applied, the load will energize for the time delay then de-energize. Reset: Reclosing SW1 resets the timer. Appendix B, page 165, Figure 4 for dimensional drawing. P/N: P P/N: P P/N: P (AWG 10/12) Plug-on adjustment module: P/N: VTP()() s s m m m VTP P/N VTP5G VTP5K VTP5N VTP5P VTP5R Delay-on- Break Selection Table for VTP Plug-on Accessory. V = Voltage L = Load S1 = Initiate Switch THD72110SA THD7415SB THD7421C THD7612MA THD7621C THD7 Voltage 2 - External adjust * m m Type....Digital integrated circuitry Range....1s m in 5 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±10% Recycle Time....After timing: 150ms; During timing: 350ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Type....Solid state Form....NO, closed during timing Rating Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A Rating A - 6A B - 10A C - 20A *If fixed delay is selected, insert delay (1-1000) followed by (S) sec. or ( )(M) min. Effective Voltage Drop (VLine-VLoad) Effective Drop 24VAC 3V 120VAC 3V 230VAC 5V Minimum Load Current...100mA Circuitry...Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **...Surface mount with one #10 (M5 x 0.8) screw Dimensions...2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity...95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

33 Timer - Delay-on-Break TSB Series S1 = Initiate Switch UTL = Optional Untimed Load L = Load The TSB Series is a totally solid-state, delay-onbreak timing module. The TSB is available with a fixed, external, or onboard adjustable time delay. s from 0.05 to 600 seconds, in 4 standard ranges, cover over 90% of all OEM and commercial appliance timing applications. The repeat accuracy is ±2%. Operating voltages of 24, 120, or 230VAC are available. The TSB s 1A steady state, 10A rated, solid-state output is perfect for direct control of solenoids, contactors, relays, lamps, buzzers, and small heaters. The TSB can be surface mounted with a single screw, or snapped on a 35 mm DIN rail using the P adaptor. Operation (Delay-on-Break): voltage must be applied before and during timing. Upon closure of the initiate switch, the output energizes. The time delay begins when the initiate switch opens. The output remains energized during timing. At the end of the time delay, the output de-energizes. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reclosing the initiate switch during timing resets the time delay. Loss of input voltage resets the output and the time delay. Appendix B, page 165, Figure 1 for dimensional drawing. Fixed or adjustable s in 4 ranges Totally solid state & encapsulated ± 2% repeat accuracy ±5% factory calibration - TSB2130 TSB2190 TSB222 TSB232 TSB4110 TSB41300 TSB414 TSB4170 TSB418 TSB4190 TSB422 TSB423 TSB424 TSB432 TSB434 TSB632 TSB634 TSB Voltage 2 - External adjust 3 - Onboard adjust * s s s s *If fixed delay is selected, insert delay ( ) in seconds. Range s - 600s in 4 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% vs Temp. & Voltage.... ±10% Reset Time ms Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, closed before & during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C Off State Leakage Current VAC Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

34 Timer - Single Shot TDS / TDSH / TDSL Series 8-pin octal SPDT The TDS Series combines accurate digital circuitry with isolated, 10A rated, DPDT or SPDT relay contacts in an 8 or 11-pin plug-in package. The TDS Series features DIP switch selectable time delays ranging from 0.1s to 10,230s in three ranges. The TDS Series is the product of choice for custom control panel and OEM designers. Operation (Single Shot): voltage must be applied to the input before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output relay energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 8 for dimensional drawing. Digi-Set Binary Switch Operation: Switch selectable time delay Three time ranges from 0.1s - 10,230s ±0.1% repeat accuracy ±2% setting accuracy 10A, SPDT or DPDT output contacts LED indication TDS120AL TDS120ALD TDS12D TDS230AL TDS24AL TDS24DL 8-pin models UL listed when used in combination with P socket only. Panel mount kit: P/N: BZ1 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) P/N: PSC11 (NDS-11) 11-pin socket: P/N: NDS-11 Octal 8-pin socket: P/N: NDS-8 Octal socket for UL listing: P/N: P TDSH120AL TDSH120ALD TDSH24ALD TDS20AL TDS2D TDSL24D 11-pin DPDT S1 = Initiate Switch Relay contacts are isolated. TDS s in 1s increments TDSH ,230s in 10s increments TDSL s in 0.1s increments Voltage 12D - 12VDC 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC LED* L Type....Digital integrated circuitry Range** s in 0.1s increments s in 1s increments 10-10,230s in 10s increments Repeat Accuracy....±0.1% or 20ms, whichever is greater Setting Accuracy....±2% or 50ms, whichever is greater Reset Time ms Recycle Time ms vs Temp. & Voltage....±5% Indicator....LED glows during timing; relay is energized Initiate Time ms Voltage , 24/28, or 110VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency....50/60 Hz Power Consumption W Type of Plug / Form Blank - Octal (8-pin) plug, SPDT D - 11-pin Plug, DPDT * Note: LED not available in 12VDC Type....Electromechanical relay Form....SPDT & DPDT Rating....10A 120/240VAC & 28 VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Isolation Voltage V RMS input to output Polarity....DC units are reverse polarity protected Mounting....Plug-in socket Dimensions x 2.4 x 1.8 in. (81.3 x 60.7 x 45.2 mm) Termination....Octal 8-pin plug-in or 11-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g) **For CE approved applications, power must be removed from the unit when a switch position is changed.

35 Timer - Single Shot TRS Series The TRS Series combines an isolated, 10A electromechanical, relay output with analog timing circuitry. False trigger of the TRS by a transient is unlikely because of the complete isolation of the circuit from the line prior to initiation. The initiate contact is common to one side of the line and may be utilized to operate other loads. Installation is easy due to the TRS s industry standard 8 or 11-pin plug-in base wiring. Knob adjustable time delays Fixed or adjustable s in 15 ranges Analog circuitry ±2% repeat accuracy AC & DC operating voltages are available Isolated, 10A, SPDT & DPDT output contacts 8-pin octal SPDT Operation (Single Shot): voltage must be applied to the input before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. Applying input voltage with the initiate switch closed will energize the load and begin the time delay. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 9 for dimensional drawing. 8-pin models UL listed when used in combination with P socket only. P/N: P1004- P/N: P Octal socket for UL listing: P/N: P Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) P/N: PSC11 (NDS-11) Octal 8-pin socket: P/N: NDS-8 11-pin socket: P/N: NDS-11 Panel mount kit: P/N: BZ1 TRS Voltage 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC 11-pin SPDT 11-pin DPDT S1 = Initiate Switch Relay contacts are isolated. is used when external adjustment is ordered. and Form, Octal, SPDT (AC Volts only) 2 - Knob Adjust, Octal, SPDT (AC Volts only) 3 - Lock Shaft Adjust, Octal, SPDT (AC Volts only) 4 - Knob adjust, 11-pin, DPDT 7 - Ext. Adjust, 11-pin, SPDT without potentiometer 10 - Fixed, 11-pin, DPDT External P/N Selection Table Value 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm 1M ohm 1.5M ohm 2M ohm 3M ohm 5M ohm Type.... Analog circuitry Range s - 10m in 15 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Fixed Time Tolerance & Setting Accuracy... ±5, 10, or 20% Initiate Time ms Reset Time ms Recycle Time ms vs Temp. & Voltage.... ±10% Voltage /28 or 110VDC; 24, 120, or 230VAC (DC voltages on DPDT output models only) Tolerance 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency /60 Hz Power Consumption W Part Number P P P P P P P P P P Time Tolerance - ±20% Y - ±10% Z - ±5% *If fixed delay is selected, insert delay ( ) in seconds. * (seconds) TRS120A1300 TRS120A2300 TRS120A4Z3 TRS24D7Z10 TRS24D7Z3 Type.... Electromechanical relay Form.... Isolated SPDT or DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Insulation Resistance MΩ Isolation Voltage V RMS between input & output terminals Polarity.... DC units are reverse polarity protected Mounting... Plug-in socket Termination.... Octal 8-pin plug-in or 11-pin plug-in Dimensions x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g)

36 Timer - Single Shot The PRLS Series is designed for use on non-critical timing applications. It offers low cost, knob adjustable timing control; full 10A relay output; and onboard LED indication. The knob adjustment provides a guaranteed time range of up to 10 minutes in 6 ranges. The onboard LED indicates whether or not the unit is timing (flashing LED) as well as the status of the output. Operation (Single Shot): voltage must be applied to the input at all times prior to and during timing. Upon closure of the initiate switch (momentary or maintained) the output contacts transfer and the time delay is initiated. The LED flashes during timing. At the end of the delay, the output contacts revert to their original position. If the initiate switch is reclosed during timing, the time delay will not be affected. Applying input voltage with the intiate switch closed will energize the load and begin the time delay. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 9 for dimensional drawing. PRLS Series Knob adjustable time delay relay Electronic circuit with electromechanical relay AC & DC operating voltages Standard, octal plug-in connection Fixed or adjustable s in 6 ranges ±2% repeat accuracy ±10% factory calibration LED indication 10A, SPDT output contacts Panel mount kit: P/N: BZ1 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) Octal 8-pin socket: P/N: NDS-8 PRLS625 S1 = Initiate Switch V = Voltage Relay contacts are isolated. PRLS Voltage 1-12VDC 3-24VDC 5-110VDC 1 - Factory Fixed 2 - Adjustable * s s s s s s *If fixed delay is selected, insert delay ( ) in seconds. Type....Analog circuitry Range s in 6 adjustable ranges or fixed Repeat Accuracy....±2% or 20ms, whichever is greater Tolerance....Knob adjust: guaranteed range Fixed: ±10% Reset Time ms Recycle Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC; 12, 24, or 110VDC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency....50/60 Hz Power Consumption W Type....Electromechanical relay Form....Isolated SPDT Rating....10A 28VDC; 10A 240VAC; 1/3 120 & 240VAC Life x10 7 ; Electrical - 1x10 6 Surge....IEEE C Level A Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Indication Type....LED Operation.... energized & timing - flashing Mounting....Plug-in socket Dimensions x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Termination....Octal 8-pin, plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g)

37 Timer - Single Shot HRDS Series The HRDS Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230V operation in five options and factory fixed, onboard or external adjustable time delays with a repeat accuracy of ±0.5%. The output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. This series is ideal for OEM applications where cost is a factor. 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Encapsulated circuitry Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy Factory fixed, onboard or external adjust Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output relay energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 2 for dimensional drawing. - P/N: P (AWG 10/12) NO = Normally Open S1 = Initiate Switch L = Load C = Common, Transfer Contact NOTE: A knob, or terminals 4 & 5 are only included on adjustable units. is used when external adjustment is ordered. Relay contacts are not isolated. External Resistance vs. : HRDS120 HRDS124 HRDS21120S HRDS220 HRDS221 HRDS222 HRDS223 HRDS313M HRDS320 HRDS321 HRDS322 HRDS323 HRDS324 HRDS420 HRDS421 HRDS422 HRDS423 HRDS424 HRDS430 HRDS Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Time Tolerance Blank - ±5% A - ±1% * m *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) (M) min. Type.... Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration).... ±1%, ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% AC Line Frequency /60 Hz Power Consumption.... AC 4VA; DC 2W Type.... Electromechanical relay Form.... Non-isolated, SPDT Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge... IEEE C Level A Circuitry... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity... DC units are reverse polarity protected Mounting... Surface mount with one #10 (M5 x 0.8) screw Dimensions... 3 x 2 x 1.5 in (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C/-40 to 85 C Humidity... 95% relative, non-condensing Weight oz (111 g)

38 Timer - Interval/Single Shot ERDI Series Interval Econo-Timers are a combination of digital electronics and an electromechanical relay. DPDT relay output for relay logic circuits, and isolation of input to output voltages. For applications, such as interval on, pulse shaping, minimum run time, etc. The ERD Series is encapsulated to protect the circuitry from shock, vibration and humidity. Operation (Interval): Upon application of input voltage, time delay begins, and output relay energizes. At the end of time delay, output de-energizes until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Operation (Single Shot): voltage must be applied before & during timing. Upon momentary or maintained closure of initiate switch, output relay energizes for time delay. At the end of the delay, output de-energizes. Opening or reclosing initiate switch during timing has no affect on time delay. will energize if initiate switch is closed when input voltage is applied. Reset: Reset occurs when time delay is complete & initiate switch is opened. Loss of input voltage resets time delay & output. Appendix B, page 165, Figure 10 for dimensional drawing. Factory fixed, onboard or external adjust Delays from 0.1s m in 11 ranges ±0.5% repeat accuracy ± 10% factory calibration Encapsulated digital circuitry Isolated 10A, DPDT output contacts P/N: P P/N: P ERDI1210 ERDI123 ERDI323 ERDI326 ERDI4311 ERDI436 ERDI628 Single Shot 2-3 & 7-6 are Normally Open Contacts (NO) 2-4 & 7-5 are Normally Closed Contacts (NC) A knob, or terminals 9 & 10 are included on adjustable units. Relay contacts are isolated. is used when external adjustment is ordered. ERDI Voltage 1-12VDC 3-24VDC 5-120VDC 2 - Onboard knob 3 - External adjust * s s s s s s Type.... Digital integrated circuitry Range s - 500m in 11 adjustable ranges, 0.1s m fixed.... Knob, external adjust, or fixed Repeat Accuracy.... ±0.5% Tolerance (Factory Calibration).... ±10% Reset Time ms vs Temp. & Voltage.... ±2% Voltage , 24, or 120VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 120VDC/AC & 230VAC % - 10% AC Line Frequency /60 Hz Type.... Isolated relay contacts m m m m m *If fixed delay is selected, insert delay ( ) followed by (S) sec, or (M) min. Form.... DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with two #6 (M3.5 x 0.6) screws Dimensions x 2.5 x 1.7 in. (88.9 x 63.5 x 43.2 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -40 to 85 C Weight oz (162 g)

39 Timer - Single Shot The ORS Series open PCB construction offers the user good economy without sacrificing performance and reliability. The output relay is available in isolated, 10A, DPDT or SPDT forms. The time delay may be ordered as factory fixed, onboard knob, or external adjustment. All connections are 0.25 in. (6.35 mm) male quick connect terminals. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output relay energizes for a measured interval of time. At the end of the time delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 11 for dimensional drawing. ORS Series Low cost open PCB construction Momentary or maintained initiation 10A, DPDT or SPDT output contacts Delays from 0.05s - 300s in 5 ranges ±2% repeat accuracy ±10% factory calibration P/N: P P/N: P ORS120A1180 ORS120A33 ORS230A150SD SPDT DPDT Relay contacts are isolated. ORS Voltage 24A - 24VAC 120A - 120VAC 230A - 230VAC 2 - Onboard knob 3 - External adjust * s s s s s Type.... Analog circuitry Range s in 5 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... Adjustable: guaranteed range Fixed: ±10% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance 24VAC % - 20% 120 & 230VAC % - 10% AC Line Frequency /60 Hz Power Consumption W Form Blank - SPDT D - DPDT *If fixed delay is selected, insert delay ( ) in seconds. Type.... Electromechanical relay Form.... Isolated, SPDT or DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x10 7 ; Electrical - 1x10 6 Isolation Voltage V RMS input to output Mounting.... Surface mount with four #6 (M3.5 x 0.6) screws Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (77 g)

40 Timer - Single Shot V = Voltage S1 = Initiate Switch C = Common, Transfer Contact NO = Normally Open NC = Normally Closed UTL = Untimed Load A knob is supplied for adjustable units. The untimed load is optional. Relay contacts are isolated. The KRDS Series is a compact time delay relay measuring only 2 in. (50.8 mm) square. Its microcontroller timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDS Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output relay energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : KRDS Series Compact time delay relay ±0.5% repeat accuracy Isolated, 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s m in 6 ranges ±5% factory calibration voltages from 12 to 230V in 5 options - P/N: P (AWG 10/12) KRDS120 KRDS221 KRDS225 KRDS424 KRDS430 Current/Ambient Temperature: KRDS Voltage 1-12VDC /DC 5-110VDC 2 - Onboard knob 3 - External adjust Type....Microcontroller with watchdog circuitry Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±5% Voltage , 24 or 110VDC; 24, 120 or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC, 120VAC or 230VAC %- 10% AC Line Frequency / DC Ripple....50/60 Hz / 10% Power Consumption....AC 2VA; DC 2W Type....Isolated relay contacts Form....SPDT * m *If fixed delay is selected, insert delay ( m ) followed by (S) sec, or (M) min. Rating (at 40 C)....10A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry....Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals.... Operating / Storage Temperature to 60 C/-40 to 85 C Humidity....95% relative, non-condensing Weight oz (74 g)

41 Timer - Single Shot The TDUS Series combines digital timing circuitry with universal voltage operation. Voltages of 24 to 240VAC and 12 to 24VDC are available in three ranges. The TDUS Series offers DIP switch selectable time delays ranging from 0.1 seconds to minutes in three ranges. Its 1A rated output, ability to operate on multiple voltages, and wide range of switch selectable time delays make the TDUS Series an excellent choice for process control systems and OEM equipment. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Switch selectable time setting 0.1s m in 3 ranges ± 0.5% repeat accuracy ± 2% setting accuracy 1A, solid-state output Encapsulated Wide voltage ranges TDUS Series P/N: P (AWG 10/12) P/N: P (AWG 18/22) TDUS3000A TDUS3002A TDUSL3000A UTL = Optional Untimed Load S1 = Initiate Switch L = Timed Load Voltage Range 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC Time Range s s s s s s m m m Part Number TDUSL3000A TDUSL3001A TDUSL3002A TDUS3000A TDUS3001A TDUS3002A TDUSH3000A TDUSH3001A TDUSH3002A Range* s in 0.1s increments s in 1s increments m in 0.1m increments Repeat Accuracy....±0.5% or 20 ms, whichever is greater Setting Accuracy.... ±2% or 20 ms, whichever is greater Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±5% Voltage/Tolerance to 240VAC, 12 to 24VDC /±20% AC Line Frequency / DC Ripple....50/60 Hz / 10% Power Consumption....AC 2VA; DC 1W Type....Solid state Form....NO, closed during timing Rating....1A steady state, 10A inrush at 60 C Voltage Drop....AC 1A; DC 1A Off State Leakage Current....AC 230VAC; DC 1 ma Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g) *For CE approved applications, power must be removed from the unit when a switch position is changed.

42 Timer - Single Shot TSDS Series (Positive Switching) (Negative Switching) The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance are required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 1000 minutes are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. This product is suitable for many applications, including dispensing, welding, and exposure timing. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will not energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Fixed or adjustable delays 0.1s m in 6 ranges ±0.5% repeat accuracy ±1% factory calibration 12VDC to 230VAC in 5 options 1A, solid-state output Encapsulated - L = Timed Load UTL = Optional Untimed Load S1 = Initiate Switch Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : TSDS11390SP TSDS2110S TSDS320N TSDS321P TSDS421 TSDS Voltage 1-12VDC 3-24VDC 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance....±15% Power Consumption....AC 2VA; DC 1W AC Line Frequency / DC Ripple....50/60 Hz / 10% Type....Solid state Form....NO, closed during timing Maximum Load Current....1A steady state, 10A inrush at 60 C Switching Mode (VDC only) P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Voltage Drop....AC 1A; DC 1A Off State Leakage Current....AC 230VAC; DC 1mA DC Operation....Positive or negative switching Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

43 Timer - Single Shot UTL = Optional Untimed Load L = Timed Load S1 = Initiate Switch The THDS Series combines accurate timing circuitry with high power solid-state switching. It can switch motors, lamps, and heaters directly without a contactor. You can reduce labor, component cost, and increase reliability with these small, easy-to-use, Digi-Power timers. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output energizes if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 4 for dimensional drawing. External Resistance vs. : THDS Series High load currents up to 20A, 200A inrush Fixed or adjustable delays from 0.1s m ±0.5% repeat accuracy ±1% factory calibration 24, 120, or 230VAC Metallized mounting surface for heat transfer Totally solid state and encapsulated - P/N: P (AWG 10/12) THDS230C THDS231C THDS232C THDS233C THDS234C THDS235C THDS410.25SA THDS411.5SA THDS414MC THDS420B THDS430C THDS432C THDS433C THDS434C THDS435C THDS610.25SA THDS611.5SA THDS Voltage 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, closed during timing Maximum Load Current Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A Rating A - 6A B - 10A C - 20A *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. Voltage Drop.... rated current Off State Leakage Current VAC Minimum Load Current mA Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

44 Timer - Single Shot UTL = Optional Untimed Load L = Timed Load S1 = Initiate Switch (Positive Switching) (Negative Switching) The KSDS Series is ideal for applications that require momentary start interval timing including dispensing, exposure timing, or pulse shaping. This series is available for both AC and DC voltages. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid-state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will not energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch is opened. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : KSDS Series Fixed or adjustable delays 0.1s m in 6 ranges ±0.5% repeat accuracy ± 5% factory calibration 12 to 230V in 5 ranges 1A, solid-state output - KSDS1115SP KSDS121P KSDS130P KSDS310.1SP KSDS330P KSDS415M KSDS420 KSDS Voltage 1-12VDC 3-24VDC 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage or 24VDC; 24, 120, or 230VAC Tolerance....±20% AC Line Frequency / DC Ripple....50/60 Hz / 10 % Power Consumption....AC 2VA; DC 1W Type....Solid state Form....NO, closed during timing Maximum Load Current....1A steady state, 10A inrush at 60 C Switching Mode (VDC only) P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. OFF State Leakage Current....AC 230VAC; DC 1mA Voltage Drop....AC 1A; DC 1A DC Operation....Positive or negative switching Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

45 Timer - Single Shot TSS Series The TSS is a totally solid-state timing module. Its 1A rated, solid-state output provides an excellent method of time control for exposures, dispensing, or for increasing or decreasing a switch closure. Time delays from 0.05 to 600 seconds, in 4 ranges, cover 90% of all OEM applications. Factory calibration of fixed delays is ±5% and the repeat accuracy is ±2%. The TSS can be surface mounted with a single screw, or snapped on a 35mm DIN rail using the P accessory adaptor. Operation (Single Shot): Voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch opens. Loss of input voltage resets the time delay and output. Appendix B, page 165, Figure 1 for dimensional drawing. Expands or decreases switch closures Momentary or maintained initiate switch Totally solid state Encapsulated to protect against shock & vibration Fixed or adjustable delays from s in 4 ranges ±2% repeat accuracy ±5% factory calibration - S1 = Initiate Switch L = Timed Load UTL = Optional Untimed Load TSS223 TSS410.5 TSS421 TSS422 TSS424 TSS432 TSS622 TSS624 TSS Voltage 2 - External adjust 3 - Onboard adjust * s s s s Range s - 600s in 4 adjustable ranges or fixed Repeat Accuracy....±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NO, closed during timing *If fixed delay is selected, insert delay ( ) in seconds. Maximum Load Current....1A steady state, 10A inrush at 60 C Off State Leakage Current VAC Voltage Drop.... 1A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / - 40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

46 Timer - Single Shot THC / THS Series The TH series is a solid-state relay and timer combined into one compact, easy-to-use control. When mounted to a metal surface, the TH Series may be used to directly control lamp or heater loads of up to 20A steady, 200A inrush. Its single shot function can perform dispensing and pulse shaping operations. The initiate switch can be a momentary or maintained type of switch. Time delays can be selected from seconds in 4 ranges. The THC Series is used for coin vending applications where fast initiate response is required. Operation (Single Shot): voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch (leading edge triggered), the output energizes for a measured interval of time. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no affect on the time delay. The output will energize if the initiate switch is closed when input voltage is applied. Reset: Reset occurs when the time delay is complete and the initiate switch opens. Loss of input voltage resets the time delay and output. High load current capacity, up to 20A, 200A inrush Momentary or maintained initiate switch ±2% repeat accuracy ±5% factory calibration Fixed or adjustable s in 4 ranges Metallized mounting surface for heat transfer - P/N: P (AWG 10/12) Appendix B, page 165, Figure 4 for dimensional drawing. THC41180B THC421C THS422B S1 = Initiate Switch L = Timed Load UTL = Optional Untimed Load THC / THS Voltage 2 - External adjust 3 - Onboard adjust * s s s s Rating A - 6A B - 10A C - 20A *If fixed delay is selected, insert delay ( ) in seconds. Range s in 4 adjustable ranges or fixed Repeat Accuracy....±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 5% Reset Time ms Initiate Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance....±15% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NO, closed during timing Maximum Load Currents Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A Minimum Load Current mA Voltage Drop V at rated current OFF State Leakage Current VAC Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

47 Timer - Retriggerable Single Shot The HRD9 Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230V operation in five ranges and factory fixed, external, or onboard adjustable time delays with a repeat accuracy of ±0.5%. The isolated output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. The HRD9 is ideal for OEM applications where cost is a factor. HRD9 Series Isolated, 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Delays from 0.1s - 100m in 5 ranges 0.5% repeat timing accuracy Factory fixed, onboard or external adjust Encapsulated circuitry Operation (Motion Detector/Retriggerable Single Shot): voltage must be applied prior to and during timing. The output is de-energized. Upon closure of the initiate switch (momentary or maintained) the output energizes and the time delay starts. On completion of the delay period, the output de-energizes. Reset: Reclosing the initiate switch during or after timing will reset the time delay and restart timing. Reset is also accomplished by removing and reapplying input voltage. Note: Powering up the unit with the initiate switch closed will not energize the output relay or start timing. Appendix B, page 165, Figure 2 for dimensional drawing. - P/N: P (AWG 10/12) Quick connect to screw adaptor: (Positive Switching) (Negative Switching) HRD93110S HRD9320 External Resistance vs. : S1 = Initiate Switch L = Timed Load UTL = Untimed Load (optional) NO = Normally Open C = Common, Transfer Contact NOTE: A knob, or terminals 4 & 5 are only included on adjustable units. is used when external adjustment is ordered. Relay contacts are isolated. The untimed load is optional. HRD9 Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Time Tolerance Blank - ±5% A - ±1% *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) (M) min. Type.... Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1%, ±5% Reset Time ms vs Temp. & Voltage.... ±2% Initiate Time ms ( 1500 operations per min.) Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% AC Line Frequency /60 Hz Power Consumption.... AC 4VA; DC 2W Type.... Electromechanical relay Form.... Isolated, SPDT Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** * m Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge.... IEEE C Level A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C/-40 to 85 C Humidity % relative, non-condensing Weight oz (111 g)

48 Timer - Retriggerable Single Shot KRD9 Series C = Common, Transfer Contact UTL = Untimed Load (optional) A knob is supplied for adjustable units, or terminals 4 & 5 for external adjust. See external adjustment vs time delay chart. The untimed load is optional. Relay contacts are isolated. The KRD9 Series microcontroller timing circuit provides excellent repeat accuracy and stability. Cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Retriggerable Single Shot): Function Type A ( Initially De-energized): voltage must be applied prior to and during timing. When the initiate switch is closed, (momentary or maintained) the output energizes and the time delay starts. On completion of the delay, the output de-energizes. The unit will time out if S1 remains in the open or closed position for the full time delay. Reclosing the initiate switch resets the time delay and restarts timing; the output remains energized. The output will not energize if the initiate switch is closed when input voltage is applied. Function Type B ( Initially Energized): Upon application of input voltage, the output energizes and the time delay starts. At the end of the time delay, the load de-energizes. The unit will time out if S1 remains in the open or closed position for the full time delay. Closing (re-closing) the initiate switch resets the time delay and restarts timing; the output remains energized. Reset: The time delay and the output are reset when input voltage is removed. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Compact time delay relay Microcontroller circuitry ±0.5% repeat accuracy Isolated, 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s m in 6 ranges voltages from 12 to 230V in 6 options - P/N: P (AWG 10/12) KRD9120B KRD92115MA KRD92115MB KRD9220B KRD93115MA KRD94115SB KRD9423B Current / Ambient Temperature: KRD9 Voltage 1-12VDC /DC 3-24VDC 5-110VDC 2 - Onboard knob 3 - External adjust * m m Type.... Microcontroller based with watchdog circuitry Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms Initiate Time ms; 750 operations per minute vs Temp. & Voltage.... ±5% Voltage , 24 or 110VDC; 24, 120 or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC, 120 or 230VAC % - 10% AC Line Frequency / DC Ripple /60 Hz / 10% Power Consumption.... AC 2VA; DC 2W Type.... Isolated relay contacts Form.... SPDT Function Type A - De-energized B - Energized *If fixed delay is selected, insert delay ( ) followed by (S) sec, or (M) min. Rating (at 40 C) A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC Max. Switching Voltage VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry.... Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity.... DC units are reversed polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (74 g)

49 Timer - Interval TDI / TDIH / TDIL Series The TDI Series is an interval timer that combines accurate digital circuitry with isolated, 10A rated, DPDT relay contacts in an 8-pin plug-in package. The TDI Series features DIP switch selectable time delays ranging from 0.1 to 10,230 seconds in three ranges. The TDI Series is the product of choice for custom control panel and OEM designers. Operation (Interval): Upon application of input voltage, the time delay begins. The output relay is energized during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 8 for dimensional drawing. Digi-Set Binary Switch Operation: Switch settable time delay Three time ranges from 0.1s - 10,230s ±0.1% repeat accuracy ±2% setting accuracy 10A, DPDT output contacts LED indication Panel mount kit: P/N: BZ1 Octal 8-pin socket: P/N: NDS-8 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) TDI120AL TDI12D TDI230AL TDI24AL TDI24DL TDIH24AL TDI20AL TDIL24DL Relay contacts are isolated. TDI s in 1s increments TDIH ,230s in 10s increments TDIL s in 0.1s increments Voltage 12D - 12VDC 24A - 24VAC 24D - 24VDC/28VDC 110D - 110VDC 120A - 120VAC 230A - 230VAC Type.... Digital integrated circuitry Range** s in 0.1s increments s in 1s increments 10-10,230s in 10s increments Repeat Accuracy.... ±0.1% or 20ms, whichever is greater Setting Accuracy.... ±2% or 50ms, whichever is greater Reset Time ms Recycle Time ms vs Temp. & Voltage.... ±2% Indicator.... LED glows during timing; relay is energized Voltage , 24, or 110VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency /60 Hz Power Consumption W Type.... Electromechanical relay LED Indication* L * Note: LED not available in 12VDC Form.... DPDT Rating A 120/240VAC & 28VDC; 1/3 120/240VAC Life x10 7 ; Electrical - 1 x 10 6 Polarity.... DC units are reverse polarity protected Isolation Voltage V RMS input to output Mounting.... Plug-in socket Dimensions x 2.4 x 1.8 in. (81.3 x 60.7 x 45.2 mm) Termination.... Octal 8-pin plug-in Operating / Storage Temperature to 65 C / -30 to 85 C Weight oz (170 g) ** For CE approved applications, power must be removed from the unit when a switch position is changed.

50 Timer - Interval HRDI Series The HRDI Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230V operation in five ranges and factory fixed, external, or onboard adjustable time delays with a repeat accuracy of ±0.5%. The output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. This series is ideal for OEM applications where cost is a factor. 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Encapsulated circuitry Delays from 0.1s - 100m in 5 ranges ±0.5% repeat timing accuracy Factory fixed, onboard or external adjust Operation (Interval): Upon application of input voltage, the time delay begins. The output relay is energized during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 2 for dimensional drawing. External Resistance vs. : - P/N: P (AWG 10/12) C = Common, Transfer Contact NO = Normally Open L = Load NOTE: A knob, or terminals 4 & 5 are only T included on adjustable units. is used when external adjustment is ordered. Relay contacts are not isolated. HRDI117S HRDI220 HRDI221 HRDI222 HRDI223 HRDI224 HRDI320 HRDI321 HRDI322 HRDI323 HRDI324 HRDI4130M HRDI421 HRDI422 HRDI423 HRDI424 HRDI431 HRDI Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Time Tolerance Blank - ±5% A - ±1% Type....Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration)....±1%, ±5% Recycle Time ms vs Temp. & Voltage....±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% AC Line Frequency....50/60 Hz Power Consumption....AC 4VA; DC 2W Type....Electromechanical relay Form....SPDT, non-isolated Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** * *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) m (M) min. Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge....IEEE C Level A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....3 x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g)

51 Timer - Interval KRDI Series The KRDI Series is a compact time-delay relay measuring only 2 in. (50.8 mm) square. Its solidstate timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDI Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Interval): Upon application of input voltage, the time delay begins. The output relay energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Compact time delay relay 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy ±5% factory calibration voltages from 12 to 230V in 6 options - P/N: P (AWG 10/12) KRDI1132S KRDI120 KRDI121 KRDI122 KRDI210.1S KRDI2110S KRDI21120S KRDI320 KRDI420 KRDI423 V = Voltage C = Common, Transfer Contact NO = Normally Open NC = Normally Closed A knob is supplied for adjustable units, or RT terminals 4 & 5 for external adjust. See external adjustment vs time delay chart. Relay contacts are isolated. Current/Ambient Temperature: KRDI Voltage 1-12VDC 3-24VDC 5-110VDC 2 - Onboard knob 3 - External adjust Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 5% Reset Time ms vs Temp. & Voltage.... ±5% Voltage , 24 or 110VDC; 24, 120 or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC, 120VAC or 230VAC % - 10% AC Line Frequency / DC Ripple....50/60 Hz / 10% Power Consumption....AC 2VA; DC 2W Type....Isolated relay contacts Form....SPDT Rating (at 40 C)....10A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC * *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) m (M) min. Max. Switching Voltage VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry....Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (74 g)

52 Timer - Interval TDUI Series The TDUI Series combines digital timing circuitry with universal voltage operation. Voltages of 24 to 240VAC and 12 to 24VDC are available in three ranges. The TDUI Series offers DIP switch selectable time delays ranging from 0.1 seconds to minutes in three ranges. Its 1A rated output, ability to operate on multiple voltages, and wide range of switch selectable time delays make the TDUI Series an excellent choice for process control systems and OEM equipment. Switch selectable time setting 0.1s m in 3 ranges ±0.5% repeat accuracy ±2% setting accuracy 1A, solid-state output Encapsulated Wide voltage ranges Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. P/N: P (AWG 10/12) P/N: P (AWG 18/22) TDUI3000A TDUIH3001A TDUIH3002A TDUIL3002A Voltage Range 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC 24 to 120VAC 100 to 240VAC 12 to 24VDC Time Range s s s s s s m m m Part Number TDUIL3000A TDUIL3001A TDUIL3002A TDUI3000A TDUI3001A TDUI3002A TDUIH3000A TDUIH3001A TDUIH3002A Range* s in 0.1s increments s in 1s increments m in 0.1m increments Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Setting Accuracy.... ±2% or 20ms, whichever is greater Reset Time ms vs Temp. & Voltage.... ±5% Voltage to 240VAC, 12 to 24VDC ±20% AC Line Frequency /60 Hz Power Consumption.... AC 2VA; DC 1W DC Ripple % Type.... Solid state Form.... NO, closed during timing Rating.... 1A steady state, 10A inrush at 60 C Voltage Drop.... 1A; DC 1A OFF State Leakage Current.... AC 230VAC; DC 1mA Circuitry Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g) *For CE approved applications, power must be removed from the unit when a switch position is changed.

53 Timer - Interval TSD2 Series The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance are required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Fixed or adjustable delays from 0.1s - 100h ±0.1% repeat accuracy ±1% factory calibration 24, 120, or 230VAC 1A, solid-state output Encapsulated Operation (Interval): Upon application of input voltage, the time delay begins. The output is energized during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. - External Resistance vs. : TSD2221 TSD2411S TSD24145S TSD241600S TSD2434 TSD2 Voltage 2 - External adjust 3 - Onboard adjust * m m h Range s - 100h in 7 adjustable ranges or fixed Repeat Accuracy.... ±0.1% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms vs Temp. & Voltage.... ±1% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Form.... NO, closed during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. or (1-100) (H) hours Off State Leakage Current VAC Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

54 Timer - Interval THD2 Series The THD2 Series combines accurate timing circuitry with high power solid-state switching. It can switch motors, lamps, and heaters directly without a contactor. You can reduce labor, component cost, and increase reliability with these small, easy-to-use, Digi-Power timers. Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. High load currents up to 20A, 200A inrush Fixed or adjustable delays from 0.1s m ±0.5% repeat accuracy ±1% factory calibration 24, 120, or 230VAC Metallized mounting surface for heat transfer Totally solid state and encapsulated Appendix B, page 165, Figure 4 for dimensional drawing. External Resistance vs. : - P/N: P (AWG 10/12) S1 = Optional Low Current Initiate Switch THD2B4110M THD2B41600S THD2B6110M THD2C231 THD2C232 THD2C233 THD2C234 THD2C235 THD2C423 THD2C430 THD2C431 THD2C432 THD2C433 THD2C434 THD2C435 THD2 Rating A - 6A B - 10A C - 20A Voltage 2 - External adjust 3 - Onboard adjust Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms vs Temp. & Voltage.... ±2% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Type....Solid state Form....NO, closed during timing Maximum Load Current Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A * m m *If fixed delay is selected, insert delay (1-1000) followed by (S) secs. or (M) mins. Minimum Load Current mA Voltage Drop V at rated current OFF State Leakage Current VAC Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

55 Timer - Interval (Positive Switching) (Negative Switching) The TSD6 offers total solid-state, interval timing for 12 or 24VDC applications. This series provides either negative or positive switching. The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance is required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : TSD6 Series Fixed or adjustable delays from 0.1s - 100h ±0.1% repeat accuracy ±1% factory calibration 12 or 24VDC interval timing 1A, solid-state output Encapsulated - TSD6113SN TSD6121N TSD6121P TSD6123N TSD6124P TSD6310.8SN TSD631180SP TSD631380SP TSD6320P TSD6334P TSD6 Voltage 1-12VDC 3-24VDC 2 - External adjust 3 - Onboard adjust * m m h Range s - 100h 7 adjustable ranges or fixed Repeat Accuracy.... ±0.1% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1% Reset Time ms vs Temp. & Voltage.... ±1% Voltage or 24VDC Tolerance.... ±15% DC Ripple.... ±10% Power Consumption.... 1W Type.... Solid state, positive or negative switching Form.... NO, closed during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C Switching Mode P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. or (1-100) (H) hours Off State Leakage Current.... 1mA Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... Units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

56 Timer - Interval The KSD2 Series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable, solid-state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for input voltages of 24, 120 or 230VAC. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. An excellent choice for most OEM pulse shaping, maximum run time, and other process control applications. Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : KSD2 Series Fixed or adjustable delays from 0.1s m ±0.5% repeat accuracy ± 5% factory calibration 24, 120, or 230VAC 1A, solid-state output Encapsulated - KSD2211M KSD2221 KSD2413M KSD2420 KSD2 Voltage 2 - External adjust 3 - Onboard adjust * m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NO, closed during timing Maximum Load Current....1A steady state, 10A inrush at 60 C *If fixed delay is selected, insert delay ( ) followed by (S) secs. or (M) mins. OFF State Leakage Current VAC Voltage Drop.... 1A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

57 Timer - Interval TS2 / TS6 Series The TS2 Series is designed for 24, 120 or 230VAC and the TS6 Series is designed for 12 or 24VDC. These series are capable of controlling load currents of up to 1A steady state, 10A inrush. Encapsulated circuitry and the reliability of a ±2% repeat accuracy make the TS2 and TS6 ideal for cost sensitive applications. Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and the output. Appendix B, page 165, Figure 1 for dimensional drawing. 12 or 24VDC; 24,120, or 230VAC input voltages Fixed or adjustable delays from 0.05s - 10m in 8 ranges Repeat accuracy ±2% Load currents to 1A, 10A inrush Totally solid state & encapsulated P/N: P1004- P/N: P Plug-on adjustment module: P/N: VTP()() TS6 12VDC VTP P/N s s s s VTP2A VTP2E VTP2F VTP2H Note: TS6 is not reverse polarity protected. Order Tables: TS2 Voltage TS6 Voltage 1-12VDC 3-24VDC 2 - External adjust 2 - External adjust Type... Analog circuitry Range * s s s s * 12VDC s s s s 12VDC s in 4 adjustable ranges or fixed (1 MΩ max. ) Other Voltages s in 4 adjustable ranges or fixed Repeat Accuracy.... ±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±10% vs Temp. & Voltage.... ±10% Reset Time ms Voltage or 24VDC; 24, 120, or 230VAC Tolerance.... ±15% DC Ripple % Power Consumption.... DC 1W; AC 2VA Type.... Solid state *If fixed delay is selected, insert delay ( ) in seconds. 24VDC s s 2-180s 5-600s Switching Mode P - Positive TS22120 TS2213 TS2223 TS TS24110 TS2412 TS2413 TS24130 *If fixed delay is selected, insert delay ( VDC) or ( VDC) in secs. TS2 & TS6 All Other Voltages s s s s Selection Table for VTP Plug-on Accessory. TS2421 TS2422 TS2423 TS2424 TS TS26130 TS26190 TS2621 VTP P/N VTP4B VTP4F VTP4J VTP5N TS6116P TS6122P TS6123P TS6311P TS63110P TS6321P Form.... NO, closed during timing Maximum Load Current.... 1A steady state, 10A inrush at 60 C Voltage Drop.... DC 1A; AC 1A Circuitry.... Encapsulated Polarity... TS6 is not reverse polarity protected Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

58 Timer - Interval TH2 Series The TH2 is the combination of a timer and a solidstate relay into one easy-to-use solid-state molded module. When mounted to a metal surface, the TH2 Series can switch load currents up to 20A steady state with 200A inrush. The TH2 replaces a timer and relay at a competitive price. Operation (Interval): Upon application of input voltage, the time delay begins. The output energizes during the time delay. At the end of the time delay, the output de-energizes and remains de-energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Appendix B, page 165, Figure 4 for dimensional drawing. Features High load current capacity up to 20A, 200A inrush Fixed or adjustable time delays from s in 4 ranges ±2% repeat accuracy ±5% factory calibration Metallized mounting surface for heat transfer Solid state & encapsulated - P/N: P (AWG 10/12) TH2A421 TH2 Rating A - 6A B - 10A C - 20A Voltage 2 - External adjust 3 - Onboard adjust Range s - 600s in 4 adjustable ranges, or fixed Repeat Accuracy....±2% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% vs Temp. & Voltage.... ±10% Reset Time ms Voltage , 120, or 230VAC Tolerance....±15% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Form....NO, closed during timing Maximum Load Currents Steady State Inrush** A 6A 60A B 10A 100A C 20A 200A * s s s *If fixed delay is selected, insert s delay ( ) in seconds. Minimum Load Current mA Voltage Drop V at rated current OFF State Leakage Current VAC Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting **....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16ms.

59 Timer - Recycling Relay contacts are isolated. The TDR Series of time-delay relays are comprised of digital circuitry and an isolated, 10A relay output. The on and off delays are selected by means of two, ten position binary switches, which allow the setting of the desired delay to be precise every time. Operation (Recycling - ON Time First): Upon application of input voltage, the green LED glows, the output relay is energized, the red LED glows, and the T1 ON time begins. At the end of the ON time, the output de-energizes, the red LED turns OFF and the T2, OFF time begins. At the end of the OFF time, the output relay energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the first delay. Operation (Recycling - OFF Time First): Upon application of input voltage, the green LED glows, the T1 OFF time begins, the load is OFF. At the end of the OFF time, the T2 ON time begins, the load energizes, and the red LED glows. At the end of the ON time the load de-energizes and the red LED turns OFF. The cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to the OFF time. Appendix B, page 165, Figure 8 for dimensional drawing. Digi-Set Binary Switch Operation: TDR Series Switch settable time delays - both times adjustable 0.1s h in 3 ranges ±0.1% repeat accuracy ±2% setting accuracy Isolated, 10A, DPDT output contacts Octal plug-in base connection Panel mount kit: P/N: BZ1 Octal 8-pin socket: P/N: NDS-8 Hold-down clips (sold in pairs): P/N: PSC8 (NDS-8) TDR1A22 TDR2A22 TDR2A23 TDR4A11 TDR4A12 TDR4A13 TDR4A22 TDR4A23 TDR4A33 TDR4B22 TDR4B23 TDR6A22 TDR Voltage A - 24 to 240VAC/DC D - 12* to 48VDC 1-12VDC* 3-24VDC 5-110VDC Sequence A - ON Time First B - OFF Time First ON Time s in 0.1s increments s in 1s increments ,230s in 10s increments *Control status LED not available on 12VDC units. Type.... Microcontroller circuitry Range** s in 0.1s increments s in 1s increments 10-10,230s in 10s increments Repeat Accuracy.... ±0.1% or 20ms, whichever is greater Setting Accuracy.... ±2% or 50ms, whichever is greater Reset Time ms Recycle Time ms vs Temp. & Voltage.... ±2% Voltage to 24VDC, 110VDC, 24, 120, or 230VAC; 24 to 240VAC/DC; 12 to 48VDC Tolerance 12VDC & 24VDC/AC % - 20% 110 to 230VAC/DC % - 10% AC Line Frequency / DC Ripple /60 Hz / 10% Power Consumption.... AC 2VA; DC 2W LED Indicator.... Green; On when input voltage is applied Type.... Electromechanical relay OFF Time s in 0.1s increments s in 1s increments ,230s in 10s increments Form.... DPDT Rating A 120/240VAC & 30VDC; 1/3 230VAC Life x10 7 ; Electrical - 1 x 10 5 Max. Switching Voltage VAC Relay LED Indicator.... Red; ON when output relay energizes Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Plug-in socket Dimensions x 2.39 x 1.78 in. (81.3 x 60.7 x 45.2 mm) Termination.... Octal 8-pin plug-in Operating / Storage Temperature to 60 C / -30 to 85 C Weight oz (170 g) **For CE approved applications, power must be removed from the unit when a switch position is changed.

60 Timer - Recycling NO = Normally Open S1 = Reset Switch C = Common, Transfer Contact L = Load Terminals 4 & 5 and/or 7 & 8 are only included on externally adjustable units. Relay contacts are non-isolated. is included when external adjustment is ordered. Terminal 6 is included when Bypass/Reset is selected. The HRDR Series combines an electromechanical relay and microcontroller timing circuitry. It offers 12 to 230V operation in five ranges and factory fixed, onboard or externally adjustable time delays with a repeat accuracy of ±0.5%. The high switching capacity of the output contacts allow for direct control of heavy loads like compressors, pumps, motors, heaters and lighting. A bypass/ reset switch option allows operator to interrupt normal recycling sequence and energize output relay. An excellent choice for OEM applications. Operation (Recycling with Reset Switch): Upon application of input voltage, the ON time T1 begins and output relay energizes. At the end of the ON time, the output relay de-energizes and the OFF time T2 begins. At the end of the OFF time, the output relay energizes and the cycle repeats as long as input voltage is applied. Some recycling timers have the OFF time as the first delay. Reset: Removing input voltage resets output and time delays, and returns sequence to the first delay. Bypass/Reset Switch: Closing the normally open bypass/ reset switch energizes the output relay and resets the time delays. Opening the switch restarts recycling operation with the first delay. Appendix B, page 165, Figure 2 for dimensional drawing. External Resistance vs. : Features HRDR Series 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Encapsulated circuitry Delays from 0.1s m in 6 ranges Independent adjustment of on and off delays ±0.5% repeat accuracy ±5% factory calibration Factory fixed, onboard or external adjust - P/N: P (AWG 10/12) HRDR11720MB60S HRDR120A1R HRDR121A4R HRDR130A0R HRDR321A4R HRDR322B2R HRDR330A0R HRDR331A1 HRDR4110MB20M HRDR431A1R HRDR Voltage 1-12VDC 3-24VDC External Adjust 1 - Both Times Fixed 2 - Both Times Onboard Adj. 3 - Both Times External Adj. 4 - ON Time External Adj. OFF Time Fixed 5 - ON Time Fixed OFF Time External Adj. 6 - ON Time Onboard Adj. OFF Time Fixed 7 - ON Time Fixed OFF Time Onboard Adj. 8 - ON Time Onboard Adj. OFF Time External Adj. 9 - ON Time External Adj. OFF Time Onboard Adj. Range ms m in 6 adjustable ranges or fixed Repeat Accuracy... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration)... ±5% Reset Time ms vs Temp. & Voltage... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC...-15% - 20% 24 to 230VAC...-20% - 10% AC Line Frequency... 50/60 Hz Power Consumption... AC 4VA; DC 2W Type... Electromechanical relay Form... SPDT, non-isolated Ratings: SPDT- NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** T1 ON Time* m m Operating Sequence A - ON time first B - OFF time first T2 OFF Time* m m *If fixed delay is selected, insert delay ( ) followed by (S) sec. or ( ) (M) min. Operation Blank - NoBypass/ Reset Option R - Bypass/Reset Option Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge.... IEEE C Level A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative non-condensing Weight oz (111 g)

61 Timer - Recycling C = Common, Transfer Contact NO = Normally Open L = Load NOTE: A knob, or terminals 4 & 5 are only included on adjustable units. RT is used when external adjustment is ordered. Relay contacts are not isolated. The HRD3 Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230V operation in five options and factory fixed, external, or onboard adjustable time delays with a repeat accuracy of ±0.5%. The output contact rating allows for direct operation of heavy loads, such as compressors, pumps, blower motors, heaters, etc. This series is ideal for OEM applications where cost is a factor. Operation (Recycling - ON Time First): Upon application of input voltage, the output relay energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the T2 OFF time begins. At the end of the OFF time, the output relay energizes and the cycle repeats as long as input voltage is applied Reset: Removing input voltage resets the output and time delays, and returns the sequence to the first delay. Operation (Recycling - OFF Time First): Upon application of input voltage, the T2, OFF time begins. At the end of the OFF time, the T1, ON time begins and the load energizes. At the end of the ON time the load de-energizes, and the cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to the OFF time. Appendix B, page 165, Figure 2 for dimensional drawing. External Resistance vs. : HRD3 Series Equal on and off delays 30A, SPDT, NO output contacts 12 to 230V operation in 5 options Encapsulated Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy Factory fixed, onboard or external adjust - P/N: P (AWG 10/12) HRD3220A HRD3221A HRD3222A HRD3223A HRD3224A HRD3320A HRD3321A HRD3322A HRD3323A HRD3324A HRD3420A HRD3421A HRD3422A HRD3423A HRD342A0A HRD3 Voltage 1-12VDC 3-24VDC 2 - Onboard knob 3 - External adjust Time Tolerance Blank - ±5% A - ±1% Type.... Microcontroller circuitry Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±1%, ±5% Reset Time ms vs Temp. & Voltage.... ±2% Voltage or 24VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC % - 20% 24 to 230VAC % - 10% Line Frequency /60 Hz Power Consumption.... AC 4VA; DC 2W Type.... Electromechanical relay Form.... Non-isolated, SPDT Ratings: SPDT-NO SPDT-NC General Purpose 125/240VAC 30A 15A Resistive 125/240VAC 30A 15A 28VDC 20A 10A * m Operating Sequence A - ON Time First B - OFF Time First *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) (M) min. Motor Load 125VAC 1 hp* 1/4 hp** 240VAC 2 hp** 1 hp** Life x 10 6 ; Electrical - 1 x 10 5, *3 x 10 4, **6,000 Surge.... IEEE C Level A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.5 in. (76.7 x 51.3 x 38.1 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (111 g)

62 Timer - Recycling ERD3 Series Econo-Timers are a combination of digital electronics and a reliable electromechanical relay. DPDT relay output for relay logic circuits, and isolation of input to output voltages. Cost effective for OEM applications, such as duty cycling, drying, washing, signaling, and flashing. Operation (Recycling - ON Time First): Upon application of input voltage, the output relay energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the T2 OFF time begins. At the end of the OFF time, the output relay energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the first delay. Operation (Recycling - OFF Time First): Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the T1 ON time begins and the load energizes. At the end of the ON time the load de-energizes, and the cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to the OFF time. Appendix B, page 165, Figure 10 for dimensional drawing. Features Factory fixed, onboard or external adjust Delays from 0.1s m ±0.5% repeat accuracy Encapsulated digital circuitry Isolated, 10A, DPDT output contacts P/N: P P/N: P ERD3425A A knob, or terminals 9 & 10 are only included on adjustable units. Relay contacts are isolated. RT is used when external adjustment is ordered. ERD3 Voltage 1-12VDC 3-24VDC 5-120VDC 2 - Onboard knob 3 - External adjust * s s s s s s m m m s m Type....Digital integrated circuitry Range s - 500m in 11 adjustable ranges 0.1s m fixed....knob, external adjust, or fixed Repeat Accuracy....±0.5% Tolerance (Factory Calibration).... ±10% Reset Time ms vs Temp. & Voltage.... ±2% Voltage , 24, or 120VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 120VAC/DC & 230VAC % - 10% AC Line Frequency....50/60 Hz Type....Isolated relay contacts Operating Sequence A - ON Time First B - OFF Time First *If fixed delay is selected, insert delay ( ) followed by (S) sec, or (M) min. Form....DPDT Rating....10A 120/240VAC & 28VDC; 1/3 120/240VAC Life x 10 7 ; Electrical - 1 x 10 6 Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with two #6 (M3.5 x 0.6) screws Dimensions x 2.5 x 1.7 in. (88.9 x 63.5 x 43.2 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 65 C / -40 to 85 C Weight oz (162 g)

63 Timer - Recycling T1 = OFF Time T2 = ON Time NO = Normally Open NC = Normally Closed C = Common A knob is supplied for adjustable units. The KRDR Series is a compact time-delay relay measuring only 2 in. (50.8 mm) square. Its solidstate timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDR Series is a cost effective recycling timer for OEM applications that require small size, isolation, reliability, and long life. Operation (Recycling - ON Time First): Upon application of input voltage, the output relay energizes and the T2 ON time begins. At the end of the ON time, the output de-energizes and the T1 OFF time begins. At the end of the OFF time, the output relay energizes and the cycle repeats as long as input voltage is applied Reset: Removing input voltage resets the output and the time delays, and returns the sequence to the ON time. Operation (Recycling - OFF Time First): Upon application of input voltage, the T1 OFF time begins. At the end of the OFF time, the T2 ON time begins and the load energizes. At the end of the ON time the load de-energizes, and the cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to the OFF time. Appendix B, page 165, Figure 1 for dimensional drawing. Current/Ambient Temperature: KRDR Series Compact time delay relay 10A, SPDT output contacts Factory fixed or onboard adjust Delays from 0.1s m in 6 ranges voltages from 120 to 230V in 6 options ±0.5% repeat accuracy ±5% factory calibration P/N: P (AWG 10/12) KRDR115MB25M KRDR120A0 KRDR123A4 KRDR124A4 KRDR320A1 KRDR320B0 KRDR321A4 KRDR321B4 KRDR421A4 KRDR424A0 KRDR440.5SA0 KRDR Voltage 1-12VDC 3-24VDC 5-110VDC s 1 - Both Times Fixed 2 - Both Times Adj. 3 - ON Time Adj. OFF Time Fixed 4 - ON Time Fixed OFF Time Adj. T2 ON Time* m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.5 % or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms vs Temp. & Voltage.... ±5% Voltage , 24 or 110VDC; 24, 120 or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC & 120 or 230VAC % - 10% AC Line Frequency / DC Ripple....50/60 Hz / 10% Power Consumption....AC 2VA; DC 2W Type....Isolated relay contacts Form....SPDT Rating (at 40 C)....10A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC Operating Sequence A - ON time first B - OFF time first T1 OFF Time* *If fixed delay is selected, insert m delay ( ) followed by (S) sec m or (M) min. Max. Switching Voltage VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry....Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 60 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (74 g)

64 Timer - Recycling V = Voltage C = Common, Transfer Contact NO = Normally Open NC = Normally Closed A knob is supplied for adjustable units, or RT terminals 4 & 5 for external adjust. See external adjustment vs time delay chart. Relay contacts are isolated. The KRD3 Series measures only 2 in. (50.8 mm) square. Its solid-state timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRD3 Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Operation (Recycling Flasher - ON Time First): Upon application of input voltage, the output energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the T2 OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to T1 ON time. Operation (Recycling Flasher - OFF Time First): Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the T1 ON time begins and the load energizes. At the end of T1, T2 begins and the load de-energizes. This cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to T2 OFF time. Appendix B, page 165, Figure 1 for dimensional drawing. External Resistance vs. : Features KRD3 Series Compact time-delay relay 10A, SPDT output contacts Factory fixed, onboard or external adjust Delays from 0.1s - 100m in 5 ranges ±0.5% repeat accuracy ±5% factory calibration voltages from 12 to 230V in 5 options - P/N: P (AWG 10/12) KRD3110.4SA KRD31160SA KRD3420A KRD3434A Current/Ambient Temperature: KRD3 Voltage 1-12VDC 5-110VDC 2 - Onboard knob 3 - External adjust * m Range s - 100m in 5 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 5% Reset Time ms vs Temp. & Voltage.... ±5% Voltage , 24 or 110VDC; 24, 120, or 230VAC Tolerance 12VDC & 24VDC/AC % - 20% 110VDC, 120 or 230VAC % - 10% AC Line Frequency / DC Ripple /60 Hz / 10% Power Consumption.... AC 2VA; DC 2W Type.... Isolated relay contacts Form.... SPDT Rating (at 40 C) A 125VAC; 5A 230VAC & 28VDC; 1/4 125VAC Operating Sequence A - ON Time First B - OFF Time First *If fixed delay is selected, insert delay ( ) followed by (S) sec, or ( ) (M) min. Max. Switching voltage VAC Life (Operations) x 10 7 ; Electrical - 1 x 10 5 Circuitry.... Encapsulated Isolation Voltage V RMS input to output Insulation Resistance MΩ Polarity.... DC units are reverse polarity protected Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals.... Operating / Storage Temperature to 60 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (74 g)

65 Timer - Recycling RS Series The RS Series is a solid-state, encapsulated, recycling timer designed for tough industrial environments. It is used by many testing labs as a life cycle tester; by others as a cycle controller. The RS Series has separate DIP switch adjustments for the on delay and the off delay. These make accurate adjustment possible the first time, every time. Time delays of 0.1 seconds to 1023 hours are available in 4 ranges. Operation (Recycling - ON Time First) Upon application of input voltage, the output energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the T2 OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the ON time. Operation (Recycling - OFF Time First) Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the output energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the OFF time. Appendix B, page 165, Figure 2 for dimensional drawing. Accurate, reliable, recycling timer Switch settable time delays - both times adjustable ±0.1% repeat accuracy ±2% setting accuracy 0.1s h in 4 ranges 12 to 230V in 5 options 1A, solid-state output Totally solid state and encapsulated RS1A11 RS1A12 RS1B12 RS2A12 RS2A24 RS2B44 RS4A11 RS4A12 RS4A13 RS4A22 RS4A24 RS4A31 RS4A33 RS4B23 RS6A13 RS6A24 L = Load RS Voltage 1-12VDC 3-24VDC Operating Sequence A - ON time first B - OFF time first T1 ON Time s in 0.1s increments m in 0.1m increments m in 1m increments h in 1h increments Range* s in 0.1s increments m in 0.1m increments m in 1m increments h in 1h increments Repeat Accuracy...±0.1% or 20ms, whichever is greater Setting Accuracy....< ±2% or 20ms, whichever is greater Reset Time....< 150ms vs Temp. & Voltage....< ± 2% Voltage , or 24VDC; 24, 120, or 230VAC Tolerance....±20% AC Line Frequency / DC Ripple....50/60 Hz / < ±10% Power Consumption....AC < 2VA; DC < 1W Type....Solid state Maximum Load Current....1A steady state, 10A inrush at 60 C T2 OFF Time s in 0.1s increments m in 0.1m increments m in 1m increments h in 1h increments OFF State Leakage Current....AC 230VAC; DC 1mA Voltage Drop....AC 1A; DC 1A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....3 x 2 x 1.5 in (76.7 x 51.3 x 38.1 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (111 g) *For CE approved applications, power must be removed from the unit when a switch position is changed.

66 Timer - Recycling (Positive Switching) (Negative Switching) V = Voltage L = Load T1 = ON Time T2 = OFF Time A knob is supplied for adjustment on the unit; terminals for external adjustment. The ESDR Series offers independent time adjustment of both delay periods. options include fixed, onboard or external adjust. The ESDR is recommended for air drying, automatic oiling, life testing, chemical metering and automatic duty cycling. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable, solid-state timer is required. The factory calibration for fixed time delays is <±5%. The repeat accuracy, under stable conditions, is 0.1% of the selected time delay. This series is designed for input voltages of 12VDC to 230VAC in five ranges. Time delays of 0.1 seconds to 1000 minutes are available in six ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Recycling - ON Time First): Upon application of input voltage, the output energizes and the T1, ON time begins. At the end of the ON time, the output de-energizes and the T2, OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the first delay. Operation (Recycling - OFF Time First): Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the output energizes and the T1 ON time begins. At the end of the ON time, the output de-energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the first delay. Appendix B, page 165, Figure 1 for dimensional drawing. Features ESDR Series ON/OFF recycling with independent adjustment of both the on and off periods Factory fixed, onboard or external adjust 0.1s to 1000m in 6 ranges ±0.1% repeat accuracy ± 5% factory calibration Available in AC or DC voltages - ESDR120A0P ESDR120A1P ESDR120A4P ESDR120B3P ESDR121A2P ESDR121A3P ESDR123A0P ESDR123B4P ESDR124A0P ESDR125A5P ESDR152B1P ESDR221A2 ESDR221B5 ESDR224B4 ESDR310.7SA10SP ESDR320A0P ESDR320A3P ESDR420A1 ESDR420A4 ESDR420B1 ESDR420B4 ESDR421A1 ESDR421A4 ESDR421B1 ESDR423A4 ESDR423B1 ESDR424A0 ESDR424A4 ESDR450A1 ESDR452B1 ESDR620B3 ESDR621A1 ESDR650A1 ESDR Voltage 1-12VDC 3-24VDC External Adjust 1 - Both Times Fixed 2 - Both Times Onboard Adj. 3 - ON Time Onboard Adj. OFF Time Fixed 4 - ON Time Fixed OFF Time Onboard Adj. 5 - Both Times External Adj. 6 - ON Time External Adj. OFF Time Fixed 7 - ON Time Fixed OFF Time External Adj. 8 - ON Time Onboard Adj. OFF Time External Adj. 9 - ON Time External Adj. OFF Time Onboard Adj. Range s m in 6 adjustable ranges or fixed Repeat Accuracy....±0.1% or 20ms, whichever is greater Tolerance (Factory Calibration).... ± 5% vs Temp. & Voltage.... ±2% Reset Time ms Voltage or 24VDC; 24, 120, or 230VAC Tolerance....±20% Power Consumption....AC 2VA; DC 1W AC Line Frequency / DC Ripple....50/60 Hz / 10% Type....Solid state Maximum Load Current....1A steady state, 10A inrush at 60 C T1 ON Time* m m Operating Sequence A - ON time first B - OFF time first T2 OFF Time* m m Switching Mode (VDC Only) P - Positive N - Negative *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. OFF State Leakage Current....AC 230VAC; DC 1mA Voltage Drop....AC 1A; DC 1A Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Polarity....DC units are reverse polarity protected Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)

67 Timer - Recycling An onboard adjustment, or terminals 4 & 5 are only included on adjustable units. The TSDR Digi-Timer is an on/off or off/on recycling timing module designed to control metering pumps, chemical valves, flash lamps, or use in energy saving or duty cycling applications. It may be ordered with both time delays factory fixed, or one delay fixed and the other delay external or onboard adjustable. The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance are required. The factory calibration for fixed time delays is < ±5%. The repeat accuracy, under stable conditions, is 0.5% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 1000 minutes are available. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Recycling - ON Time First): Upon application of input voltage, the output energizes and the T1, ON time begins. At the end of the ON time, the output de-energizes and the T2, OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to the T1 ON time. Operation (Recycling - OFF Time First): Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the T1 ON time begins and the load energizes. At the end of the T1, T2 begins and the load de-energizes. This cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to T2 OFF time. Appendix B, page 165, Figure 1 for dimensional drawing. TSDR Series Fixed or adjustable 0.1s m in 6 ranges ± 0.5% repeat accuracy ± 5% factory calibration 24, 120, or 230VAC 1A, solid-state output Encapsulated - P/N: P (AWG 10/12) P/N: P (AWG 18/22) TSDR2150MA5M TSDR215SB18M TSDR410.1SA0.3S TSDR410.4SB4S TSDR412.5SA0.5S TSDR412.5SA4.5S TSDR4140MA20M TSDR415SB18M TSDR440.25SA1 TSDR4412SA1 TSDR442MA2 TSDR4430SA2 TSDR450.3SA1 TSDR6110SA30S TSDR612.5SA4.5S TSDR615SB18M TSDR Voltage 1 - Both Times Fixed 2 - ON Time Onboard Adj. OFF Time Fixed 3 - ON Time External Adj. OFF Time Fixed 4 - ON Time Fixed OFF Time External Adj. 5 - ON Time Fixed OFF Time Onboard Adj. T1 ON Time* m m Range s m in 6 adjustable ranges or fixed Repeat Accuracy.... ±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms vs Temp. & Voltage.... ±5% Voltage , 120, or 230VAC Tolerance.... ±20% AC Line Frequency /60 Hz Power Consumption.... 2VA Type.... Solid state Maximum Load Current.... 1A steady state, 10A inrush at 60 C First Delay A - ON time B - OFF time *If fixed delay is selected, insert delay ( ) followed by (S) sec. or (M) min. T2 OFF Time* m m Off State Leakage Current VAC Voltage Drop.... 1A Circuitry.... Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting.... Surface mount with one #10 (M5 x 0.8) screw Dimensions x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity % relative, non-condensing Weight oz (68 g)

68 Timer - Recycling The KSDR Series offers independent time adjustment of both delay periods. The KSDR is recommended for air drying, automatic oiling, life testing, chemical metering, and automatic duty cycling. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable, solid-state timer is required. The factory calibration for fixed time delays is within ± 5% of the target delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for input voltages of 24, 120 or 230VAC. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1A steady and 10A inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Operation (Recycling - ON Time First) Upon application of input voltage, the output energizes and the T1, ON time begins. At the end of the ON time, the output de-energizes and the T2, OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied. Reset: Removing input voltage resets the output and time delays, and returns the sequence to T1 ON time. Operation (Recycling - OFF Time First) Upon application of input voltage, the T2 OFF time begins. At the end of the OFF time, the T1 ON time begins and the load energizes. At the end of T1, T2 begins and the load de-energizes. This cycle repeats until input voltage is removed. Reset: Removing input voltage resets the output and the sequence to T2 OFF time. Appendix B, page 165, Figure 1 for dimensional drawing. Features KSDR Series Adjustable 0.1s m in 6 ranges ±0.5% repeat accuracy ± 5% factory calibration 24, 120, or 230VAC 1A, solid-state output Encapsulated - P/N: P (AWG 10/12) P/N: P (AWG 18/22) KSDR21A1 KSDR24A4 KSDR40A0 KSDR42A4 KSDR61A4 KSDR64A4 External Resistance vs. : KSDR Voltage T1 ON Time m m Operating Sequence A - ON time first B - OFF time first Range s m in 6 ranges Repeat Accuracy....±0.5% or 20ms, whichever is greater Tolerance (Factory Calibration).... ±5% Reset Time ms vs Temp. & Voltage.... ±10% Voltage , 120, or 230VAC Tolerance....±20% AC Line Frequency....50/60 Hz Power Consumption.... 2VA Type....Solid state Rating....1A steady state, 10A inrush at 60 C T2 OFF Time m m Voltage Drop.... 1A OFF State Leakage Current VAC Circuitry....Encapsulated Dielectric Breakdown V RMS terminals to mounting surface Insulation Resistance MΩ Mounting....Surface mount with one #10 (M5 x 0.8) screw Dimensions....2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination in. (6.35 mm) male quick connect terminals Operating / Storage Temperature to 75 C / -40 to 85 C Humidity....95% relative, non-condensing Weight oz (68 g)