OTi DALI 80/ /24 TW OTi DALI 50/ /24 TW

Transcription

1 OTi DALI 80/ /24 TW OTi DALI 50/ /24 TW 24 V DALI Constant Voltage LED driver Diable range 0% - 100% Benefits Sli for factor for ounting on the cove or into luinaires. DALI Device Type 8 for Tunable White (arbitrary load distribution) Diing down to zero - range 0 100% Sooth transition to dark, iniu light 0,1% EL copliant Applications Cove lighting, wall washing, corridors, handrails, hospitality luinaires Approvals In preparation, if not already printed on product label L L1 B H Product Features DALI Device Type 8 for Tunable white Mains voltage: VAC VDC DALI steps: 0;1; Miniu light 0,1% SELV, Uout: 24 V Overload protection Lap Failure detection (open and short circuit detection) Over teperature protection tc ax = 85/70 C OTi80/OTi50 Suitable for Class I/II luinaires Sart Power Supply Wide ta range C h lifetie at tc 5 years guarantee Edition: 23 Jan 2018 Ver: 1.7 Status: Final Page 1/6 Misprints and technical changes expected

2 Electrical specification ENVIRONMEN DIMMING OUTPUT INPUT U Ite Value Rearks nit Noinal voltage V Mains frequency 0 / 50 / 60 Hz Input voltage AC V Input voltage DC V Va 2 h axiu, unit ight not operate in this Maxiu voltage 350 c abnoral condition OTi 80: 0,39 Noinal current A At 230 Vac OTi 50: 0,26 Total Haronic Distortion (THD) < 5 % Full load, 230 Vac, 50 Hz / 60 Hz see graphs Typical, Full load, 230 Vac, 50 Hz / 60 Hz, see Power factor λ 0,98 graphs ECG Efficiency OTi 80: 93 OTi 50: 92 % Typical, Full load, 230Vac, 50Hz, see graphs Power loss in stand-by ode < 500 W 230Vac, 50Hz typical 360 W Protection class II Suitable for safety class I and II luinaires Suitable for fixtures with prot. Class I / II Inrush current OTi 80: 48 Apk / 220 us OTi 50: 43 Apk / 160 us Max ECG no. on circuit breaker 10 A (B) OTi 80: B10= 6 OTi 50: B10= 9 Max ECG no. on circuit breaker 16 A (B) OTi 80: B16= 10 OTi 50: B16= 15 Max ECG no. on circuit breaker 25 A (B) OTi 80: B25 =16 OTi 50: B25= 25 Noinal output voltage 24,2 V Voltage accuracy +/- 3 % Voltage ripple < 5 % Ripple / average At 100 Hz; Full load Noinal output power OTi 80: 0 80 Power Factor, Haronics and EMI W W OTi 50: 0 50 verified between: W OTi 80: 80 Maxiu power OTi 50: 50 W Maxiu total LED output (su of both channels) Galvanic isolation SELV DC Output power (EL) 15 % Preset value, adjustable by Tuner4Tronic U-OUT (working voltage) 24,2 V Diing interface DALI (DT8) Diing range % DALI diing steps (0-254) Diing ethod PWM PWM frequency 1 kh z Galvanic Isolation Basic / Double Basic DALI to Priary / Double DALI to Secondary Abient teperature range C OTi 80: 85 Measured on t c point indicated of the prod label, t a Max. teperature at tc test point OTi 50: 70 C not exceeded Max. case tep. in fault condition 115 C Storage teperature range C Edition: 23 Jan 2018 Ver: 1.7 Status: Final Page 2/6 Misprints and technical changes expected

3 DIMENSIONS MATERIAL Peritted rel. huidity during operation 5 85 % Not condensing Surge capability (L/N) 1 kv L/N acc to. EN Environental rating Indoor IP protection class IP 20 Mains switching cycles > Expected ECG lifetie h t c = 85 C - 0,2% / h failure rate t c = 70 C - 0,1% / h failure rate No-load proof Yes Overheating protection Yes Autoatically restart Overload protection Yes Autoatically restart Short-circuit protection Yes Autoatically restart Type of connection, output side Terinal 0,2 1,5 2 Height 32 Length 345 Product weight 340 g Width 22 Casing aterial Plastic Wire prep. length, input side 5 Wire prep. length, output side 5 Mounting hole spacing, length 303 Protection Over teperature, Overload, Short-circuit, Input overvoltage, Output overvoltage. Reversible! DIP Switch not used Input Wires cross section 0,75 2,5 2 Output wire cross section 0,2 1,5 2 Wire peeling length: 5 Wiring LED wire length OSRAM verified internally that the wire length fro LED driver to LED odule at full load is up to 50t Choose a proper wire thickness to reduce the voltage drop effect Edition: 23 Jan 2018 Ver.: 1.7 Status: Final Page 3/6 Misprints and technical changes expected

4 wires 2 1 1,5 2,5 4 cross section AWG axiu cable length The values are indicative. Each connection ay increase the total voltage drop OTI DALI 80/ /24 TW OTI DALI 50/ /24 TW Edition: 23 Jan 2018 Ver.: 1.7 Status: Final Page 4/6 Misprints and technical changes expected

5 Power distribuition per channel and total Output power[%] 100% 75% 50% 25% Total LED load shall be divided in War LED load Cold LED load LED load ay be also asyetrical 0% teperature CCT [K] The su of the LED load of War and Cold channels cannot exceed the axiu power stated in the table. OSRAM syste atch: When the OTI DALI 24V TW is used in cobination with OSRAM LINEARlight flex or Signage odule, the following atching table can be use as proven syste atch. (cfr TDS of LLF for Tp definition) Tp rated Oti 50/24 TW Oti 80/24 TW in odule length [] ax odule length[] in odule length [] ax odule length[] LF4000TW-G LF3000TW-G LF2000TW-G LF1200TW-G in odule quantity ax odule quantity in odule quantity ax odule quantity BackLED TW Plus G Tp -20 C Oti 50/24 TW Oti 80/24 TW in odule length [] ax odule length[] in odule length [] ax odule length[] LF4000TW-G LF3000TW-G LF2000TW-G LF1200TW-G in odule quantity ax odule quantity in odule quantity ax odule quantity BackLED TW Plus G Rearks Input over voltage protection: ains up to 350 Vac, for 2 hours axiu, will not destroy neither the unit nor the load; Shut down of load ight occur in this condition. Output overload protection: the unit autoatically dis down to keep the output power below 80 W / 50 W. No load operation: Do not put a switch between load and unit. Edition: 23 Jan 2018 Ver.: 1.7 Status: Final Page 5/6 Misprints and technical changes expected

6 Over teperature protection: the unit is protected against teporary overheating by autoatic diing down when tc exceeds. The protection is self-restoring. Touch current: lower than 0,7 A, according to EN ann. G and EN ann. A Lap Failure detection: iniu load per channel that not trigger open circuit detection is 7.5W for OTi80 and 4.5W for OTi50. Eergency lighting: this LED power supply is suitable for eergency lighting fixtures acc. to EN , with eergency output factor EOFI= 0,15 for OTi80 and EOFI=0,24 for OTi50 ( default value, can be prograed up to EOFI=1 with Pax 12 W) and related duration tie of 10 h at least. Function in eergency is ensured up to ta=80 C and tc=96 C. Standards Ordering inforation EN EN EN Product nae EAN 10 EAN 40 Pieces / Box EN EN EN OTI DALI 80/ /24 TW OTI DALI 50/ /24 TW EN EN OSRAM GbH Head Office: Marcel-Breuer-Strasse Munich, Gerany Phone Fax Edition: 23 Jan 2018 Ver.: 1.7 Status: Final Page 6/6 Misprints and technical changes expected