IrDA Infrared Communication Module

Transcription

1 Photo ink Module Infrared Communication Module is an infrared communication module for er. 1.2 (ow Power). The infrared ED, PIN photo diode, SI are all integrated into a single package. This module is designed with power down function and low current consumption at stand-by mode. The ultra small package makes it a perfect fit for mobile devices. Features 1) Infrared ED, PIN photo diode, ED driver & Receiver frequency formation circuit built in. Improvement of EMI noise protection because of Shield Case. 2) Applied to SIR (2.4 to 115.2kbps) 3) Surface mount type. 4) Power down function built in. 5) ow voltage operation as 1.5 of interface terminals to controller (,,, TX-). 6) Infrared remote control transmission driver built-in. Applications Mobile phone, PDA, DC, Digital Still Camera, Printer, andy Terminal etc. Absolute maximum ratings (Ta=25 C) Parameter Symbol imits Unit Supply voltage max 7. 1 Input voltage in (4, 5, 6, 7pin).3 to +.3 Operation temperature Storage temperature Topr Tstg 25 to to +1 C C ED peak current IFP 3 2 ma Power dissipation Pd 3 3 mw 1 This applies to all pins basis ground pins (1pin) 2 ED Peak Current< 9µs, On duty 5% 3 When glass-epoxy board ( mm) mounted. In case operating environment is over 25 C, 4mW would be reduced per each 1 C stepping up. Recommended operating conditions (Ta=25 C) Parameter Symbol Min. Typ. Max. Unit Supply voltage Interface supply voltage ED supply voltage ED /9

2 Photo ink Module Block diagram and application circuit AMP 1 GND C1 GND 2 + AMP AMP POWER DOWN sw TX- / ED Mode EDA R1 TX- / ED Mode (ED) (3pin), (2pin) and ED (8pin) can be used on either common power source or different one 2/9

3 Photo ink Module Terminal description Pin No Terminal Circuit Function 1 GND Ground 2 Supply voltage for I/O pins. (TX-,,, ) 3 Power Supply Terminal For preventing from infection, connect a capacitor between (3pin) and GND (1pin). 4 TX- 2k Transmitting Data Input Terminal : ED Emitting CMOS ogic evel Input olding TX-='' status, ED will be turn off approximately 48µs. 5 / ED Mode Power-down Control and ED Intensity switching Terminal : POWERDOWN ( transmitting Mode) : OPERATI CMOS ogic evel Input When input is '', it will stop the receiving circuit and Pin-PD current. 6 3k Receiving Data Output Terminal CMOS ogic evel Output When (5pin)= '', the output will be pulled up to at approximately 3kΩ. 7 2k Transmitting Data Input Terminal input at = (Remote control transmitting input at =). : ED Emitting CMOS ogic evel Input olding ="" status, ED will be turn off approximately 48µs. 8 EDA ED ED ANODE Terminal Other power source can be used difference between ED and. ED current depends on ED load resistance value at mode. Shield Case Connect to Ground. 3/9

4 Photo ink Module Electrical characteristics (Unless otherwise noted, = =3., ED=3., Ta=25 C) Parameter Symbol Min. Typ. Max. Unit Conditions Consumption current1 ICC µa = At no input light Consumption current2 Data rate ICC µa kbps = At no input light input high voltage PD 2/3 =1.8 to =1.5 to 1.8 input low voltage PD 1/3 =1.8 to =1.5 to 1.8 input high current input low current IPD IPD µa µa = = <Transmitter> /TX- input high voltage /TX- input low voltage /TX- input high current /TX- input low current ED anode current ( Mode) <Receiver> output high voltage output low voltage output rise Time output fall Time output pulse width Receiver latency time TX TX ITX ITX IEDA1 RX RX trr tfr tw trt 2/ /3 1.2 ED anode current ( Mode) IEDA ma µa µa ma ns ns µs µs =1.8 to 3.6 =1.5 to 1.8 =1.8 to 3.6 =1.5 to 1.8 = or TX-= = or TX-= =, R1=4.7Ω, = TX-=, R1=4.7Ω, = IRX= 2µA IRX=2µA C=15pF C=15pF C=15pF, 2.4 to 115.2kbps Optical characteristics (Unless otherwise noted, = =3., ED=3., Ta=25 C) Parameter Symbol Min. Typ. Max. Unit Conditions Peak wave length1 ( Mode) λp nm IED=5mA, Duty2% 85 9 nm IED=5mA, Duty2%, 2 to 6 C Peak wave length2 ( Mode) λp nm IED=2mA, Duty2% Intensity1 ( Mode) IE mw/sr 15 θ 15 R1=4.7Ω Intensity2 ( Mode) IE mw/sr 15 θ 15 R1=4.7Ω alf-angle θ/2 ±15 ±22 deg Optical pulse width1 ( Mode) TWED µs =1.63µs pulse input R1=4.7Ω Optical pulse width2 ( Mode) TWED µs TX-=1µs pulse input R1=4.7Ω Rise time / Fall time Tr/Tf 6 12 ns 1% to 9% Optical over shoot 25 % Edge jitter Tj 4 4 ns Minimum Irradiance in angular Eemin µw/cm 2 15 θ +15 Maximum Irradiance in angular Eemax 5 mw/cm 2 15 θ +15 Input half-angle θd/2 ±15 deg Maximum emitting time TEDmax µs = or TX-= 1. This product is not designed for protection against radioactive rays. 2. This product dose not include laser transmitter. 3. This product includes one PIN photo diode. 4. This product dose not include optical load. 4/9

5 Photo ink Module ED Operation Mode Table (5pin) TX- (4pin) (7pin) ED Emitting Mode Receiver Operation Condition Notes) Please be sure to set up the TX- (4pin) and the (7pin) input to be '''' (under.3) except transmitting data (for < 9µs. Duty 5%). of TX- (4pin) and (7pin) in the table above is supposed to be the pulse input. When either TX- (4pin) input (7pin) input keeps the state of '''' (more than appproximately 48µs), ED will be turned off due to ED pulse width limiting circuit if the pulse is input from the other terminal. Therefore, don't use as the normal transmitting is impossible. Please input the pulse when both TX- (4pin) and (7pin) are ''''. Interface operating timing (Emitting side) (1) When output for and output for remote controller is 1 line. 1 GND Input Condition TX- ED Mode Recriver circuit / Controller 8 EDA ED TX- (4pin) Min 1µs Min 1µs Min 1µs Min 1µs ( "" ) (7pin) (5pin) ED Emitting Emitting Mode If TX- or input pulse width is wider than 48µs, output ED emitting pulse will be turn off approximately 48µs. 5/9

6 Photo ink Module (2) When output for and output for controller are different lines. 1 GND TX- Transmitting Controller (BU787X etc) / Controller 8 EDA ED (2-a) transmitting mode at receiver active condition. Input Condition TX- ED Mode Recriver circuit TX- (4pin) Min 1µs Min 1µs (7pin) (5pin) ED Emitting Emitting Mode If TX- or input pulse width is wider than 48µs, output ED emitting pulse will be turn off approximately 48µs. 6/9

7 Photo ink Module (2-b) transmit mode at receiver power down condition. Input Condition TX- ED Mode Recriver circuit Min 1µs Min 1µs TX- (4pin) Min 1µs Min 1µs (7pin) (5pin) ED Emitting Emitting Mode If TX- or input pulse width is wider than 48µs, output ED emitting pulse will be turn off approximately 48µs. (Receiving side) ight input (5pin) Min 2µs (6pin) Pull up to at approximately 3kΩ output width is fixed approximately 2.3µs. Note output become stable after 2µs since is changed from to. output could be unstable at to within 2µs. 7/9

8 Photo ink Module Attached components Recommended values Part symbol C1 R1 Recommended value 1µF, tantalum or ceramic Ex.) TCFGA1A15M8R (ROM) 4.7Ω±5%, 1/8W (ED=3) Notice Bigger capacitance is recommended with much noise from power supply At ED Emitting Duty=2% [ED current set-up method for Remote control mode] In case of using R1 with different condition from the above, formula is as follows : ED resistance value : R1[Ω], ED average consumption current : IED[mA], Supply voltage : ED[], minimum necessary of irradiant intensity le1 [mw / sr] (Including ED s distribution within ±15deg) R1=166 (ED1.28) / le15. IED=Duty (ED1.28) / (R1+3.5) Duty : ED duty at emitting Please set up to be IED / Duty < 25[mA] (Duty 5%) At Mode, ED current is constantly approximately 4mA. (Reference) In case of using R1, typical intensity (le1typ) and maximum intensity (le1max) on axis are described as below. le1typ=3 (ED1.28) / (R1+3.5) le1max=6 (ED1.28) / (R1+3.5) Notes 1) ED (8pin), (3pin) and (2pin) Other power source can be used difference between ED and and. ( < +.3) 2) Caution in designing board lay-out To get maximum potential from, please keep in mind following instruction. The line of (6pin) should be connected at backside via through hole close to pin lead. Better not to be close to photo diode side (1pin). This is to minimize feedback supplied to photo diode from. As for C1 between 1-3 pin should be placed close to. Better to be placed more than 1.cm in radius from photo diode (pin1 side) and also away from the parts which generates noise, such as DC / DC converter. 3) Notes Please be sure to set up the TX- (4pin) and the (7pin) input to be (under.3) except transmitting data (for < 9µs, duty 5%). Power down current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode. Please use by the signal format at operating mode which is specified by er1.2 (2.4k to 115.2kbps). There might be on error if used by different signal format. Please pay attention to the lens carefully. Dusts of scratch on the lens may effect the characteristics of product. Please handle it with care. 8/9

9 Photo ink Module 4) Eye safe IEC (IEC amendment2), Class 1 Eye Safe. 5) ED current derating and amdient temperature The relation between ED peak current and maximum ambient temperature is shown below. We recommend you to use within the range as indicated in below. When glass-epoxy board ( mm) mounted. MAXIMUM ED PEAK CURRENT : Iledp (ma) 3 Duty:1% 25 Duty:5% 2 Duty:4% 15 Duty:3% Duty:2% AMBIENT TEMPERATURE : Ta ( C) External dimensions (Unit : mm) ±.1.6 PinPD 8. ED.84± P.95 7= ±.1 A Part Size (Shield Case underside size) ± ±.1.6±.1 NOTE TOERANCE : ±.2mm COPANARITY :.1mmMAX A UNIT : mm ET45 9/9

10 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROM CO.,TD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROM CO.,TD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROM CO., TD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1

11 Mouser Electronics Authorized Distributor Click to iew Pricing, Inventory, Delivery & ifecycle Information: ROM Semiconductor: RPM873-E2 E4 E4A RPM873-E2A RPM873-E4A RPM873-E4 RPM882-E4