EG. Scaled 0-15Kv for PT Ratio 11Kv = 110V R/L at 11Kv Please specify range, scale & PT ratio when ordering

Transcription

1 AC AMMETER / Moving Iron Model AEC Accuracy Class: 1.% Size: 48 : 72 : 96mm 2 Standard overscale : 0%. For CT connected meters, specify CT Ratio when ordering. Type AEC 48 Type AEC 72/96 Type AEC 144 Type AEC 48 Type AEC 72/96 1 or A CT Connected 1 or A CT Connected 1 or A CT Connected : : 1 : 20 : 2 : 30 : 40 A Direct : : 1 : 20 : 2 : 30 : 40 : 0 : 60 : 7 : 80 : 0 A Direct AC VOLTMETER / Moving Iron Model VEF Accuracy Class: 1.% Size: 48 : 72 : 96mm 2 Type VEF 48 Type VEF 72/96 Type VEF 144 Type VEF PT Conn. 72/96 10 : 20 : 300 : 400 : 00 : 600V [specify voltage when ordering] 10 : 20 : 300 : 400 : 00 : 600V [specify voltage when ordering] 10 : 20 : 300 : 400 : 00 : 600V [specify voltage when ordering] EG. Scaled 0-1Kv for PT Ratio 11Kv = 1V R/L at 11Kv Please specify range, scale & PT ratio when ordering DC AMMETER / Moving Coil Model ABC Accuracy Class: 1.% Size: 48 : 72 : 96mm 2 For Non-standard Range & Scale Add R30-00 to price below Type ABC 48 Type ABC 72/96 Type ABC 144 Type ABC 48 Type ABC 72/96 0mv Input - specify range & scale when ordering 0mv Input - specify range & scale when ordering 0mv Input - specify range & scale when ordering Dc Amps Direct Max A DC (there after use shunt) Dc Amps Direct Max 30A DC (there after use shunt) DC VOLTMETER / Moving Coil Model VBC Accuracy Class: 1.% Size: 48 : 72 : 96mm 2 For Non-standard Range & Scale Add R30-00 to price below Type VBC 48 1ma to 600V direct connected [specify voltage when ordering] Type VBC 72/96 1ma to 600V direct connected [specify voltage when ordering] Type VBC 144 1ma to 600V direct connected [specify voltage when ordering] Type VBC 48 0/4-20 MA scale TBA Type VBC 72/96 0/4-20 MA scale TBA Page 1

2 Maximum Demand Ammeter Model MD [2 VA] 1 minute Bi-metal movement 2 needle Accuracy Class: Specifications: Size: 3.0% 1 min / A 72 : 96mm 2 Standard: 20% Overscale These meters measure the max mean load in 1 Minutes, as indicated by the red drag pointer. This red pointer can be reset to zero position. Overload Specs: Type MD 96 Type MD + SAT 96 Standard Instr : Full load for sec. : Full load for 1 sec. With SAT CT: Full load for 3 sec. : 20 Full load for 1 sec. Amp CT connected Maximum demand 2 needle Amp SAT CT Maximum demand 2 needle Maximum Demand Ammeter + Instantaneous Model MDI [ VA] Standard: 20% Overscale on Bi-metal 1 minute Bi-metal movement 2 needle : 0% Overscale on Instantaneous Accuracy Class: Bimetal movement 3.0% These meters measure the max mean load : Moving iron 1.% in 1 Minutes, as indicated by the red drag pointer. This red pointer can be reset to zero. Specifications: 1 min / A In addition to this it also shows the instantaneous reading of the actual load. Size: 72 : 96mm 2 Overload Specs: Type MDI 72/96 Type MDI + SAT 96 Standard Instr : Full load for sec. : Full load for 1 sec. With SAT CT: Full load for 3 sec. : 20 Full load for 1 sec. /1A Amp CT connected Maximum demand & Inst 3 Needle NB: 72/1A are not available /1A Amp SAT CT Maximum demand & Inst 3 Needle Frequency Meter Pointer Model FMP Accuracy Class: % Specifications: 4 - Hz Size: 48 : 72 : 96mm 2 FOR 2V ADD R30.00 Type FMP 48 1V : 220V [Specify voltage when ordering] Type FMP 72 1V : 220V : 380V [Specify voltage when ordering] Type FMP 96 1V : 220V : 380V [Specify voltage when ordering] Frequency Meter Reed Model FMR Accuracy Class: % Specifications: 4 - Hz Size: 72 : 96mm 2 FOR 2V ADD R30.00 Type FMR 72 1V : 220V : 380V [Specify voltage when ordering] 6-00 Type FMR 96 1V : 220V : 380V [Specify voltage when ordering] 6-00 Page 2

3 240 Degree Instruments [AC &DC] Type ABCR 48/240 Type ABC 72/96/240 Power Factor Meter Model RPF Accuracy Class: Specifications: Size: Type RPF 96 / 1 Ph 1.% Hz 96mm 2 Model ABC :DC Moving Coil Model ABCR :AC Input with rectified moving coil Accuracy Class: 1.% Specifications: Model ABC :1.1VA : Model ABCR :3.0VA Size: 48 : 72 : 96 : 144mm 2 Specify range & scale when ordering Type ABC 48/240 Standard mv & ma Ranges DC P.O.A. Type ABCR 72/96/240 Type ABC 144/240 Type RPF 96/ 3 Ph Standard V & A Ranges AC Standard mv & ma Ranges DC Standard V & A Ranges AC Standard mv & ma Ranges DC For single & 3 Phase 3 Wire (1 CT Balanced Load) Applications Graduation : 0. Lead Lag Specify Inputs Volts & Amps when ordering. 220V / 1 or A : 380 2V / 1 or A P.O.A P.O.A Synchronoscope Model RSI Accuracy Class: 1.% Specifications: 0-60Hz Max. Working Time: 1 Min. Size: 96mm 2 Type RSI 96 1 : 220 : 380 : 2V These meters are used for Phase comparison in 1 or 3 Phase circuits [Specify voltage when ordering] Phase Sequence Indicator Model FMR Accuracy Class: Operating Voltage: Max. Testing Time: Size: Frequency: Type RS 96 1.% VAC Min. 72 & 96mm Hz These meters are used for testing the correct phase sequence in 3 phase systems within the specified voltage range by holding down the button on the front face of the meter. within range of VAC Panel Meter Protection Covers / Blanking Plates IP 6 48mm IP 6 72mm IP 6 96mm 72mm Blanking Plate Black Plastic 96mm Blanking Plate Black Plastic Page 3

4 Running Hour Counters Model RH Accuracy Class: % Frequency: 0Hz Size: 48 : 72 : 96mm 2 7 Digits: Hours These elapsed Time Meters monitor On / Off time of plant and equipment. The time is measured in increments of 0.01Hrs up to Hrs, after which time the meter resets to zero. Type RH 48 Type RH 48 Type RH 72 Type RH 96 Frame : 1 : 220 : 380VAC [HM 2 Din Mount or HM1 Panel mount] - 0VDC [Within this range] 1 : 220 : 380VAC [Specify voltage when ordering] 1 : 220 : 380VAC [Specify voltage when ordering] 72mm Frame 48-72mm Selector Switches Contact Rating : 16A / 380 VAC ISO 9001 : 2000 Ammeter Selector Switch Model CA 34 / 4 Position For 3 Phase 4 wire system using 3 Current Transformers Voltmeter Selector Switch Model CV 34 / 4 and 7 Position For 3 Phase 4 wire system using 3PT s or Direct Connected Ammeter Model CA 34 4 Position : Off / Red / White / Blue Voltmeter Model CV 34 7 Position : Off / Phase / Phase & Phase / Neutral Voltmeter Model CV 33 4 Position : Off / Red / White / Blue Page 4

5 DC Round Back Meters (Moving Coil) Model JL - 60 Accuracy Class: % Size: mm 2 Cut Out: 2mm Round Type VDC JL : 30 : 0 : 0VDC [Specify when ordering] Type ADC JL - 60 : : 1ADC DIR [Specify when ordering] Type MV JL mV ADC [Specify when ordering] Dimensions: Size A B C D E F G H M For Hole JL Page

6 Panel Meters General Specifications Conform to following standards Ce18 : EN6001 : IEC414 : VDEO4 : UNE21318 : DIN43780 : IEC1 : S.A.B.S Castings Material: ABS & P.C. (Anti-Fire) Protection degree for cases: Ip2 Accuracy Class All instruments are manufactured within the 1.% or % specification, unless otherwise specified in the Data Sheet. Mounting Position Standard: Verticle Non standard to be specified when ordering. Insulation Insulation reference voltage : 0.6KV Working Temperature -2 deg. C to + Deg. C Working Voltage 660 Volt Vibration Range +/- 0.2 amplitude at 0 / 60Hz All panel meters are fitted with slide in scales and protective terminal covers. Instruments Technical Characteristics Identification Signs Negative Terminal : 1. : 2 KV 0 Class Index DC AC DC & AC Rectified Test Voltage Verticle Mounting Position Inclined Mounting [ For example 0 Deg.] Moving coil movement for DC instruments Moving iron movement for AC instruments Bi-metal movement for maximum demand indicators Vibrating reed frequency meter Outline & Cut-out Dimensions (mm) Outline Size (mm) Panel Cut-Out (mm) Additional Options Avaliable Red Line Phase Colour Bezel Company Logo Non standard Scaling Red Adj Pointer Nc Nc POA POA R27-00 Page 6

7 Electronic Kilowatt Hour Meters General Specifications Conform To :National Standard GB / T :IEC 636 : IEC 21 : IEC Accuracy :Class 1 Operating Temp : -1 C to +0 C AC Voltage withstand :2Kv for 1 min Impulse Voltage withstand Overcurrent withstand Frequency Range :6Kv - 1.2/0us :2400A / 0. Sec :0 / 60Hz ±% LCD Direct Din Rail / Chassis Mount Model DEM - 01SG / 0A 3mm Single Phase : / 0A Direct 8 Digit : 230 VAC ± 20% Operational Green Indicator Pulse Rate Indicator Red Terminal Shrouds supplied LCD Backlit KwH Backup with maintenance free lithium battery Dimensional Drawings & Wiring Diagrams for Kilowatt Hour Meters LOAD LCD 0A Direct Din Rail Chassis Mount Model DEM - 024SJ 3 Phase 4 Wire Unbalanced Load Power Consumption L1 / L2 / L3 Light Indication Phase Reversal Light Indicator Impulse Output Light Display Impulse Output Terminals LCD Backlit Kwh Backup with maintenance free lithium battery : / 0A Direct : 400 VAC ± 30% : 2W and VA / Phase Model DEM - 024SJ H W D (mm) Cut Out 4 70 Page 7

8 Electronic Kilowatt Hour Meters General Specifications Conform To :National Standard GB / T :IEC 636 : IEC 21 Accuracy :Class 1 Operating Temp : -1 C to +0 C AC Voltage withstand :2Kv for 1 min Impulse Voltage withstand Overcurrent withstand Frequency Range :6Kv - 1.2/0us :2400A / 0. Sec :0 / 60Hz ±% LCD Direct Din Rail / Chassis Mount Model DEM - 021LC 3 Phase 4 Wire Unbalanced Load Power Consumption LCD Backlit Kwh Phase Failure Light Indication Phase Reversal Light Indication Impulse Output Light Display Pulse Output Light Display Impulse Output Terminals A CT Operated Only : A CT Connected : 400 VAC ± 30% : 2W and VA / Phase Backup with maintenance free lithium battery *Please Note: For CT connected meters calculate total reading as follows. Eg. CT Ratio: 0/ Factor 20 Take Actual Reading 20 CT Ratio: 400/ Factor 80 Take Actual Reading 80 Wiring Diagram for A CT Connected Model DEM - 021LC Supply Red P1 S2 S1 H W D (mm) Cut Out Mains Supply C/B Supply White Supply Blue P2 P1 P2 P1 P2 S2 S1 S2 S1 R W B 380V NB Connection Diagrams are for illustration purposes only. We suggest you protect 380V supply to 9/11/13 Via a Fuse or circuit breaker. Page 8

9 AC Digital Panel Meter Series DG3B General Specifications Display Accuracy Operating Temperature Insulating Resistance Auxillary Supply :12mm 3 digit LED Max. 999 : ±0.% :- to 0 Deg. :2Kv / 1 min :220VAC 0/60Hz AC Meter Model DG 3BA Amp. Measuring Ranges Via Dip Switch Settings 1 / 2 / 40 / 60 / 99.9 / 10 / 20 / 400 / 600 / 999A Input: A Ac from Current Transformers AC Meter Model DG 3BV Measuring Range: 40 to 99.9Hz AC Meter Model DG 3BF Measuring Range: 40 to 99.9Hz Input Voltage: Between 40 & 600VAC AC Digital Panel Meter Series DG 3B Physical Size Connection Diagram H W D (mm) Terminal 1 and Aux 220V 0/60Hz Panel Cut Out (mm) Terminal 4 and 2 4 Amps / Volts / Frequency Input Page 9

10 AC Digital Panel Meter Series DM 9648 General Specifications 96 48mm Display :12mm 3. Digit LED Max Accuracy : ±0.% Operating Temperature :- to +0 Deg. Insulating Resistance :2Kv / 1 min Auxillary Supply :1 or 220VAC 0 / 60Hz Specify Panel Cut Out :93 4.mm Terminal pretection cover on all meters ISO 9001 : CE AC Ammeter Meter Model DM 9648-A Amp. Measuring Ranges Via Dip Switch Settings 60 / 0 / 10 / 200 / 20 / 300 / 400 / 00 / 600 / 70 / 800 / 00 / 1200 / 100 / 1999A Input: A AC from Current Transformers AC Voltmeter Meter Model DM 9648-V AC Voltmeter Meter Model DM 9648-V PT Operated Measuring Range: 0 to 600VAC AC Frequency Meter Model DM 9648-F Frequency Measuring Range Input Voltage : 40 to 99.9Hz : Between 60 & 260VAC 2 in 1 Switchable AC Amp / Volt. Meter Model DM Amp. Measuring Ranges Via Dip Switch Settings 60 / 0 / 10 / 200 / 20 / 300 / 400 / 00 / 600 / 70 / 800 / 00 / 1200 / 100 / 1999A Input Voltage Measuring Range : A AC from Current Transformers : 0 to 600VAC Page

11 AC Digital Panel Meter Series DPA 72 / 96 General Specifications 96 96mm Display :12mm 3. Digit LED Max Accuracy : ±0.% Operating Temperature :- to +0 Deg. C Insulating Resistance :2Kv / 1 min Auxillary Supply 220VAC 0Hz Panel Cut Out :92 92mm / 68 68mm Terminal pretection cover on all meters ISO 9001 : CE AC Ammeter Model DPA-1 72 / A- 999A (In A Increments Electronically Set) Input: A AC from Current Transformers A 1999A (In A Increments Electronically Set) Input: A AC from Current Transformers AC Voltmeter Model DPV-1 72 / Measuring Range Size : 0 to 600VAC : 72mm X 72mm : 96mm X 96mm Frequency Meter DPF-1 72 / Measuring Range Input Voltage : 40 to 99.9Hz : Between 40 & 600VAC Outline Size (mm) Panel Cut Out (mm) Page 11

12 Multi-Display AC Digital Panel Meter Series DMCP-3 3 Individual / LED Displays / Meter General Specifications 96 96mm Display :12mm 3. Digit LED Max Accuracy : ±0.% Operating Temperature :- to +0 Deg. C Insulating Resistance :2Kv / 1 min Auxiliary Supply 220VAC 0Hz Panel Cut Out :92 92mm Terminal pretection cover on all meters ISO 9001 : CE AC Ammeter Model DMCP96-3A Amp. Measuring Ranges Via Dip Switch Settings ( 3) 60 / 0 / 10 / 200 / 20 / 300 / 400 / 00 / 600 / 1200 / 100 / 1999A Input: A AC from Current Transformers 3 Simultaneous Displays AC Voltmeter Model DMCP96-3V Measuring Range 3 Simultaneous Displays : 0 to 600VAC ( 3) Combination AC Amp / Volt / Frequency Meter Model DMCP96-3M Amp. Measuring Ranges Via Dip Switch Settings 60 / 0 / 10 / 200 / 20 / 300 / 00 / 600 / 70 / 800 / 00 / 1200 / 100 / 1999A Input Voltage Measuring Range Frequency Measuring Range Input Voltage 3 Simultaneous Displays : A AC from Current Transformers : 40 to 600VAC : 40 to 99.9Hz : Between 40 & 600VAC Single Display Switchable AC Amp / Volt / Frequency Meter Model DMCP Specifications as per above DMCP963M Also Avaliable Ex. Import Multi Range Single & 3 Phase Power Factor (PF) Page 12

13 Emfis Digital Multifunction Panel Mounted Meter Cost effective solution to multifunction electrical parameter measurement. Unique Features Displays: Voltage Current Frequency, Power* / Power Factor etc. For 3 Phase 4 Wire Network Emfis VIF Large 3 Line Backlit LCD type Display IP 4 Degree of Protection Measures & Displays 17 parameters including: Phase to Phase Voltage Phase to Neutral Voltage Instantaneous Current Average Current Maximum Current Total Current Frequency Max Demand Current over 1 Min Time Adjustable Wiring Diagram Enclosure: Dimensions Weight Front Panel: Display Digit Height Protection Index Inputs: Current Via Current Transformer with Primary Insulated Secondary Current Circuit Burden Overload Voltage Measurement Range Voltage Circuit Burden Cut Out Technical Specifications Auxiliary Supply: Sealing Facility Provided : 96mm 96mm 86mm : 300gms : 3 Line Backlit LCD Display : 8mm 4.8mm : IP 4 : from A to 6000A configurable in multiples of : A / 1A : <0.1VA : 7A : 60V AC to 600V AC Phase Neutral : <2VA : 230 VAC ±30% 0Hz Burden <VA : 92 92mm City Power Approved Page 13

14 Temperature Controllers Application: Widely used in all kinds of cold storage, low-temperature freezers and kitchen refrigerators. Main Features: User friendly operation mode, convenient for customers to use or replace. With the function of copy card, users can set the parameters quickly during batch production or after sale service, saves time and cost. Flexible parameter setting: Sensor NTC/PTC optional, switch between Celsius and Fahrenheit. Switch between refrigeration and heating mode. Model: ETC-974 ETC-974 Type Price ETC Technical Parameters: Temperature measuring range: NTC: -0 C~1 C ( F) PTC: - C~140 C ( F) Temperature controlling range: - C~ C Relay contact output capacity: A / 20VAC Working voltage: 230VAC± %, 0/60Hz Resolution: 1 or 0.1 C Sensor: NTC (K / 2 C, B value 343K) PTC (990 / 2 C) Accessories: 2 probes, 1 operational instructions and 2 elastic tabs. Wiring Diagram: 20V A 20V A 20V A Line Def N.C. Comp. Fan Supply 220VAC Pb2 Copy key Pb1 Page 14

15 Temperature Controllers Application: Widely used in the beverage cabinets, display cases, kitchen cabinets, etc. Main Features: User friendly operation mode, convenient for customers to use or replace. With the function of copy card, users can set the parameters quickly during batch production or after sale service, high savings with time and cost. Flexible parameter setting: Sensor NTC/PTC optional, switch between Celsius and Fahrenheit. Switch between refrigeration and heating mode. Model: ETC-902 ETC-902 Type Price ETC Technical Parameters: Working voltage: 230VAC± %,0/60Hz Temperature controlling range: -0 C~99 C Resolution: 1 C / 0.1 C (Switch between interger mode and decimal mode) Accuracy: ±0. C (-1 C~30 C), others ± 1 C Sensor type: NTC (-0 C~120 C); PTC (-0 C~10 C) Accessories: 1 probe, 1 operational instructions and 2 elastic tabs. Wiring Diagram: Line Comp. 220VAC Copy key Probe Page 1

16 Temperature Controllers Application: Suitable for middle-low temperature cold storage, wind cooling cabinets, kitchen cabinets, operating consoles and refrigerating display cabinets. Main Features: Refrigerating, timing defrost modes optional Temperature exceeding alarm Upper and lower temperature limit setting Compressor delay protection time is fixed at 3 minutes Sensor error occurs, compressor turns on/off with proportional time Model: STC-8080A+ STC-8080A+ Type Price STC-8080A Specifications: Mounting size: 71 X 29 (mm) Product size: 78. X 34. X 82 (mm) Technical parameters: Power supply: 220VAC + % / -1%, 0/60HZ Tempreture measuring range: -0 C~+99 C Tempreture controlling range: -40 C~+0 C Resolution: 1 C Accuracy: (-40 C~0 C, ±1 C); others ±2 C Compressor output contact capacity: 7A/220VAC Sensor type: NTC, 2M Shell: Grey ABS flame retardant material Supply: Wiring Diagram: 220V Accessories: 1 probe, 1 operational instructions and 2 elastic tabs. 7A/220VAC 7A/220VAC STC-8080A Compressor Co-point Closed point Defrost Co-point Closed point Storage sensor Power supply 220VAC Page 16

17 Temperature Controllers Application: Widely used in middle and high-end air-cooled beverage cabinets, display cases, kitchen cabinets, ect. Main Features: Innovative design and beautiful, display area increases 0%, the character indicates work status, front panel waterproof level IP6. Easier installation: with the plug-in terminal, more reliable and higher efficiency. Adopt 30A big relay, could directly drive 1.HP single phase compressor, reducing the material cost for customers. It abandons the screw slot design at the rear of the shell, avoiding the loss caused by the condensing dripping on the circuit board. Model: ECS-0 ECS-0 Type Price ECS Specifications: Mounting size: 71 X 29 (mm) Product size: 78. X 34. X 8 (D) (mm) Technical parameters: Measuring range: -0 C ~ +90 C (when the sensor calibration is at 0) Accuracy: (-40 C~0 C, ±1 C); (0 C~70 C, ±2 C); others ±3 C Resolution: 0.1C Supply: 220V Temperature control range: -0 C~0 C Power Supply: (220±%) VAC 0Hz Power consumption: < 3W Output capacity: Refrgeration: 30A/240VAC, directly drive loading of 1.HP (240VAC) Wiring Diagram: Defrost: A/20VAC Fan: A/20VAC Front panel protection level: IP6 A A 1.HP/240VAC 20VAC 20VAC (MAX) Working enviroment Temperature: 0 C~ C Storage Temperature: -2 C~7 C Relative humidity: 20%~8% (on condensed) Accessories: 3 probe, 1 operational instructions and 2 elastic tabs. L N 220VAC N N N 0/60Hz Door switch Condenser sensor Evaporator sensor Cabinet Tempreture sensor to to to Page 17

18 Temperature Controllers Functions: 220VAC power supply, sensor error indication, small size for easy installation. Suitable for refrigerated cabinets and display cabinets ect. Model: TPM-900+ TPM-900+ Type Price TPM Specifications: Mounting size: 9 X 26 (mm) Product size: 64 X 31 (mm) Technical Parameters: Power supply: 220VAC± %, 0/60Hz Temperature measuring range: -30 C~1 C Resolution: 0.1 C (<0 C), 1 C ( 0 C) Accuracy: ±1 C Page 18

19 Acorp CT s General Specifications All CT s According to IEC 44-1 Spec DM20 Din Rail Max System Voltage : 720V AC 0/60Hz Compact Design Secondary Terminal Protection Cover CT 4/14 Chassis Mount Ease of connection on secondary terminals. CT s are supplied with brackets for Din Rail & Chassis Mounting - Depending on model. Model CT 4 / 14 14mm ID 30 to 0A Type Range VA Class Price CT14 CT14 CT14 CT14 CT14 CT14 30 / A 40 / A 0 / A 60 / A 7 / A 80 / A CT14 0 / A Primary Current : P1 - P2 Secondary Current : S1 - S2 Din Rail Mounting Model DM 20 Mini Ring 20mm ID Type Range VA Class Price DM20 0 / A DM20 60 / A DM20 7 / A DM20 80 / A DM20 0 / A DM20 12 / A DM20 10 / A DM / A DM20 20 / A DM / A to 300A Primary Current : P1 - P2 Secondary Current : S1 - S2 Page 19

20 Acorp CT s General Specifications All CT s According to IEC 44-1 Spec Max System Voltage : 720V AC 0/60Hz Secondary Terminal Protection Cover (can be sealed) CT s are supplied with brackets for Din Rail / Chassis and Busbar Mounting Kits. Ease of connection on secondary terminals. Model PWCT Wound Primary 1 to 0A Type Range Range VA Class Price 1A Price A PWCT N / A 1 / 1A PWCT N / A 2 / 1A PWCT N / A / 1A PWCT / A / 1A PWCT / A / 1A PWCT 1 / A 1 / 1A PWCT 20 / A 20 / 1A PWCT 2 / A 2 / 1A PWCT 30 / A 30 / 1A PWCT 40 / A 40 / 1A PWCT 0 / A 0 / 1A Model CP62/30 Ring CT 30mm ID 0 to 10A Type Range Range VA Class Price 1A Price A CT30 0 / A 0 / 1A CT30 60 / A 60 / 1A CT30 7 / A 7 / 1A CT30 80 / A 80 / 1A CT30 0 / A 0 / 1A CT30 12 / A 12 / 1A CT30 10 / A 10 / 1A Primary Current : P1 - P2 Secondary Current : S1 - S2 Page 20

21 Acorp CT s General Specifications All CT s According to IEC 44-1 Spec Ease of connection on secondary terminals. Max System Voltage : 720V AC 0/60Hz Secondary Terminal Protection Cover (can be sealed) CT s are supplied with brackets for Din Rail / Chassis and Busbar Mounting Kits. Model CP40 Ring CT 40mm ID 200 to 800A Type Range Range VA Class Price 1A Price A CT / A 200 / 1A CT40 20 / A 20 / 1A CT / A 300 / 1A CT / A 400 / 1A CT40 00 / A 00 / 1A CT / A 600 / 1A CT / A Model CP0 Ring CT 0mm ID Primary Current : P1 - P2 Secondary Current : S1 - S2 Type Range Range VA Class Price 1A Price A CT0 20 / A CT0 300 / A CT0 400 / A CT0 00 / A CT0 600 / A CT0 800 / A CT0 00 / A to 00A Model CP60 Ring CT 60mm ID Type Range Range VA Class Price 1A Price A Primary Current : P1 - P2 Secondary Current : S1 - S2 CT60 CT60 CT60 CT / A 20 / A 200 / 1A 20 / 1A 300 / A 300 / 1A 400 / A 400 / 1A to 2000A CT60 00 / A 00 / 1A 1 CT / A 600 / 1A 1 CT / 1A 1 CT / A 800 / 1A 1 CT60 00 / A 00 / 1A 1 1 CT / A 1 1 CT / A 1 1 CT / A 1 1 CT60 CT / A 2000 / A Primary Current : P1 - P2 Secondary Current : S1 - S2 Page 21

22 Acorp CT s General Specifications All CT s According to IEC 44-1 Spec Max System Voltage : 720V AC 0/60Hz Secondary Terminal Protection Cover (can be sealed) CT s are supplied with brackets for Din Rail / Chassis and Busbar Mounting Kits. Ease of connection on secondary terminals. Model CP80 Ring CT 80mm ID 00 to 200A Type Range VA Class CT80 00 / A 1 CT / A 1 Price 1A Price A CT / A CT80 00 / A CT / A CT / A CT / A CT80 CT / A 2000 / A Primary Current : P1 - P2 Secondary Current : S1 - S2 CT / A Model CP0 Ring CT 0mm ID 800 to 3200A Note: For Chassis and Busbar mount only Type Range VA Class CT0 800 / A CT0 00 / A 20 Price A CT0 CT / A 120 / A CT0 CT0 100 / A 1600 / A CT / A CT0 200 / A CT0 CT / A 3200 / A Primary Current : P1 - P2 Secondary Current : S1 - S2 Page 22

23 Acorp CT s General Specifications All CT s According to IEC 44-1 Spec Max System Voltage : 720V AC 0/60Hz Secondary Terminal Protection Cover (can be sealed) CT s are supplied with brackets for Din Rail / Chassis and Busbar Mounting Kits. Ease of connection on secondary terminals. Model ABO / 12 Ring CT 12mm ID 2000 to 000A Type Range VA Class Price A CT / A CT / A CT / A 0.00 CT / A CT / A CT / A Primary Current : P1 - P2 Secondary Current : S1 - S2 Clamp On Mini Split Core Current Transformers Model Uk40 / 40 Ring CT 40mm ID 0 to 800A Type Range VA Class Price A UK40 0 / A UK40 10 / A UK / A UK40 20 / A UK / A UK / A UK40 UK40 00 / A 600 / A UK / A Primary Current : P1 - P2 Secondary Current : S1 - S2 Page 23

24 Acorp CT s Acorp Mini Split Core Transformers The connection of conventional CT s usually require interruption on the primary side of the circuit to pass cables or Busbars through the transformer or to connect such cables to the primary terminals. The MSCT series transformers can be easily opened, installed and connected without any supply interruption, thus saving time and the installation costs. Features: Light weight, compact dimensions. Simple installation / Hinged Opening Built in over voltage protection. Complete with Meter Cables for Secondary Connections. Therefore no possibility of loose connections. Model M24SCT Ring CT 24mm ID Specifications: Rated Frequency Rated test voltage Operating temperature Secondary Current Max System Voltage Accuracy : 0/60Hz : 3kV AC / 1 MIN : -1 C - C : A : 720V AC 0/60Hz : Class / 3.0 0A to 300A Type M24SCT M24SCT Range 0 / A 0 / A VA Class Price A Primary Current Primary Current Secondary Current Secondary Current : P1 : P2 : S1 : S2 Line Load Red Black M24SCT 10 / A M24SCT 200 / A M24SCT 20 / A M24SCT 300 / A S1 RED S2 Black Model M36SCT Ring CT 36mm ID 400A to 600A Type M36SCT M36SCT Range 400 / A 00 / A VA Class Price A Primary Current Primary Current Secondary Current Secondary Current : P1 : P2 : S1 : S2 Line Load Red Black M36SCT 600 / A Model M24SCT Model M36SCT W H D (mm) DIA W H D (mm) DIA 36 S2 Black S1 RED Page 24

25 DBP-23 DBP Series Split Core Current Transformers The connection of conventional CT s usually require interruption on the primary side of the circuit to pass cables or Busbars through the transformer or to connect such cables to the primary terminals. The DBP series transformers can be easily opened, installed and connected without any supply interruption, thus saving time and the installation costs. Features: Two built in fixing methods: Base and Busbar mounting. Wide inner window, allowing clamping of big existing installations. Primary Current from 0-000A Type Ratio Burden (VA) D C (A) Class:0. Class:1 0/ Specifications: Rated Frequency : 0/60Hz Rated test voltage : 3kV AC Operating temperature : - C - 0 C Secondary Current : A *other technical specifications, on request ID A X B Price Standards: IEC , EN VDE , GB DBP-23 10/ DBP / DBP-8 10/ DBP-8 200/ DBP-8 20/ DBP-8 300/ DBP-8 400/ DBP-8 00/ DBP-8 600/ DBP-8 800/ DBP-8 00/ DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / DBP / Page 2

26 Acorp CT s Acorp MSCT s / Mini Sub CT General Specifications All CT s According to IEC 44-1 Spec Max System Voltage : 720V AC 0/60Hz Secondary Terminal Protection Cover. CT s are supplied with Screws for Busbar Mounting. Model MSCT / Mini Sub CT 00 to 800A Type Range VA Class Price A MSCT 00 / A 7. / 1 0. / MSCT 600 / A 7. / 1 0. / MSCT 800 / A 7. / 1 0. / Coloured Caps for Phase Indication Red White Blue Suitable for Busbars 40 X and 0 X. 42mm Primary Current : P1 - P2 Secondary Current : S1 - S2 P1 4 43mm 12mm 0mm 12mm 3mm M6 S2 23mm S1 Bracket Side View Page 26

27 Acorp CT s / Shunts Maximum System Voltage: 660V AC Chassis Mounting Summation CT s In Addition to our standard range of CT s, we are able to supply the following: Non Standard CT s manufactured to client s specifications P and P20 / P & P20 range of CT s Resin Cast CT s for Protection and metering Spilt core and Clamp-on CT s Interposing CT s Please contact us for pricing and delivery with regards to your specific requirments. Class 1 VA Summation CT Class 1 VA Summation CT Class 1 VA Summation CT / 1A and + / A / 1A and + + / A / 1A and / A DC Shunts Class 1% Range 0 & 60mV - 40A A A A A A A A A A A A A A A A 4000A POA For 7/0mV Add 20% For 10/200mV Add 0% Page 27

28 CT Dimension Page (mm) Model IDMM A B G H I J L M O P PWCT CT DM CT CT CT CT CT CT CT CT M24SC M36SC UK DBP DBP8 DBP812 DBP Page 28

29 Acorp Current Transducers Introduction The CE-T Series Providing Analogue Output Signal 4-20mA Series Operating Principal Isolation Voltage Mounting CE-IJ03A Electro Magnetic 200VDC Din Rail & Screw 1 Element AC Current Transducer Type Aux Input Output Price TCESA VAC A 4-20mA TCESA-1 1 VAC A 4-20mA TCESA VAC A 4-20mA S1 S2 Page 29

30 Moulded Terminal Blocks for Chassis Mounting Rated Current Carrying Capacity : 600VAC All With Plexiglass Terminal Protection Cover Cadmium Plated Terminal Screws / Bolts IN12BK IN13SBK IN20BK IN30BK IN411S 20A - 2 Pole 20A - 3 Pole 30A - 3 Pole 0A - 3 Pole 60A - 1 Pole TB - 13 TB - 14 TB - 16 TB A - 3 Pole 1A - 4 Pole 1A - 6 Pole 1A - 12 Pole TB - 23 TB - 24 TB A - 3 Pole 2A - 4 Pole 2A - 6 Pole TB A - 12 Pole TB TB A - 3 Pole 60A - 4 Pole TB - 03 TB A - 3 Pole 0A - 4 Pole TB TB A - 3 Pole 10A - 4 Pole TB TB A - 3 Pole 200A - 4 Pole TB TB A - 3 Pole 300A - 4 Pole TB TB A - 3 Pole 400A - 4 Pole Page 30

31 Acorp Battery Charger General Specifications Power Input Display Voltage Power Efficiency DC Output Bat12 Voltage 13.8 VDC Current A Bat24 Voltage 27.6 VDC Current 3A Charge Mode Float Contact Capacity 120V AC 0.A DC Voltage Regulator <1 :0 / 220 V AC 0/60Hz : 80 - Full Load Weight ± Grams Dimensions 11mm - L 130mm - W 73mm - H Model Battery Charger Mode of Operation 1. When Power is ON, check charge current LED bat. The current will decrease as the battery charges. 2. When Battery voltage is less than V DC the Bat < LED will illuminate and the low voltage charge fail alarm relay will energize. 3. The voltage sensing circuit automatically shuts off the power when the battery is fully charged. Installation 1. Make sure you are using the correct battery charger 12 or 24 V DC. 2. Connect Input Voltage to L1 & L2. 3. The LED marked P1 on the panel should be illuminated when the power is on. The DC output voltage should be as follows: Model BAT12 : / - 0.2V DC Model BAT24 : / - 0.2V DC 4. With power off connect output terminals ± to the battery lead ±. Use terminal lugs on connection to prevent wires from shorting. Important 1. Disconnect the power supply before any connection or disconnection is done. 2. Potentially lethal voltages are present inside. Do not open case and attemp any adjustments or repair on this unit with the power on. 3. Minimum voltage on the battery must be higher than V DC or the battery charger will automatically switch off. 4. This is not a power supply, use only for battery charging.. For use in protected environment only. Protection Current limiting protection Short circuit protection Reverse polarity protection Dimensional Drawing (mm) Page 31

32 cc Credit Application 6 Arnheim Circle - Lonehill PO Box 76 info@acorp.co.za Tel: /169 Fax: Company Name Trading Information Trading Name Street Address Postal Address Telephone Number & Area Code Fax Number & Area Code Cellular Number Address Date Company Established Type of Business Company Registration Number Vat Registration Number Partnership Private Public Close Corporation Sole Proprietor Company Information Name Telephone Number Financial Director Accounts Buyer Banking Details Banking Group Branch Name Branch Name Account Number Account Number Preferred Meathod of Payment Cash Bank Guaranteed Cheque Company Cheque Electronic Bank Transfer References Company Name Telephone Contact Person Credit Limit Account Number Credit Limit Required R Signed By: Date: Signature: Page 32

33 Acorp Standard Terms & Conditions Of Trading Prices as quoted :In SA Rand / each :VAT not Included :Subject to discount as indicated on data sheet Validity :Until Further Notice Delivery :Ex Stock Subject to prior sale :F.O.B. Johannesburg :Allow Approx. 2/7 days for non standard items All goods remain the sole property of Acorp until fully paid for. Factory & Warehouse No. 6 Arnheim Circle Lonehill 2062 Gauteng Postal Po Box 76 Lonehill 2062 Contact Details TEL : TEL : FAX : Contact Details Charles Friedrichs (Marketing) James Daly (Accounts) info@acorp.co.za Website : Banking Details Nedbank Current Account : Branch Code : VAT : Page 33