Vocia. VA-2060, VA-2060e, VA-4030, VA-4030e. Manual

Transcription

1 Vocia VA-2060, VA-2060e, VA-4030, VA-4030e Manual January 2013 Biamp Systems, 9300 SW Gemini Drive, Beaverton, Oregon U.S.A. (503)

2 IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this product near water. 6) Clean only with dry cloth. 7) Do not block ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other product (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with equipment rack, cart, stand or table designed to provide adequate mechanical strength, heat dissipation and securement to the building structure. When a cart is used, use caution when moving the cart and product combination to avoid injury from tip-over. 13) Unplug this product during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING - To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING - This product employs Safety Grounding and must be connected to a MAINS socket that is properly grounded to provide a protective earthing connection. WARNING Speaker terminals marked with the symbol are Hazardous Live. External wiring connected to these terminals requires installation by qualified electrical installer. Disconnect Device - The MAINS plug is used to disconnect MAINS power and must remain readily operable. Explanation of safety related symbols - Product labeling and the operation manual may use the internationally recognized symbols defined below to note safety messages. Lightning Bolt: Hazardous Live voltages present when this unit is in operation. Do not touch terminals marked with this symbol while the unit is connected to live power. Exclamation Point: Replace components (i.e. fuses) only with the values specified by the manufacturer. Failure to do so will compromise safe operation of this unit.

3 TABLE OF CONTENTS VOCIA AMPLIFIER VA-2060, VA-2060e, VA-4030 and VA-4030e... 3 Features...3 FRONT PANEL System Indicators...4 Amplifier Chassis Indicators...4 Amp Channel Indicators...5 Front Panel View VA VA-2060e...6 VA VA-4030e...6 REAR PANEL Conventions...7 AC Power Socket...7 Auxiliary Power...7 Network Connections...7 Device ID switches...8 Analog Audio Inputs with Phantom Power Option...8 Page Active Relay...8 Amplifier Output Connections Transformer Load Selection...9 Speaker Connection...9 Rated Load Table...9 Output Fault Detection...9 FAILOVER MODES Device-to-Device Failover...10 Channel-to-Channel Failover...11 SPECIFICATIONS Vocia Amplifier 2060 / 2060e / 4030 / 4030e...12 BLOCK DIAGRAM CURRENT DRAW AND HEAT OUTPUT WARRANTY FCC COMPLIANCE EC DECLARATION EU ROHS COMPLIANT

4 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e The VA-2060, VA-2060e, VA-4030 and VA-4030e are digital networked multi-channel audio amplifiers designed for use in Vocia systems. All models are CobraNet enabled and feature either two or four channels of amplification, with on-board DSP. Channel-to-channel or device-to-device failover may be user configured. Each amplifier channel has user selectable support for 4 or 8Ω operation or Constant Voltage operation of 25, 70 or 100 Volts. The on-board DSP provides comprehensive fixed-chain digital signal processing within the device, including volume control, ducking, equalization, compressor/limiting, speaker crossover, delay and output gain. Locally stored audio messages are retained in non-volatile memory within the amplifier. Intuitive software provides audio system design via PC computer. Two RJ45 connectors on the rear panel of the amplifier provide redundant connectivity to control data and audio over a single Ethernet cable. The VA-2060e and VA-4030e models have the ability to be powered via dual 24V connections in addition to the AC mains power supply, as well as balanced mic/line inputs to be used as a local background input source for the output channel associated with the Input. SET UP AND USE FEATURES Amplifier outputs transformer coupled to support Low Impedance or Constant Voltage loads. User selectable via rear panel switch: - Low impedance: 4 or 8Ω OR - Constant Voltage: 25V, 70V or 100V Output Power: - VA-4030(e): 4 Channel 30W RMS per channel - VA-2060(e): 2 channel 60W RMS per channel Failover capability between channels and amplifiers Locally stored audio messages are retained in non-volatile memory within the amplifier. LED Indication: - Amplifier and card failure - Clip present - Fan stuck rotor fault - Heat sink temperature fault - Signal Peak - Signal present Software Monitoring Features: - Amplifier failure - Excessive clipping - Fan stuck rotor - Temperature fault - Peak present - Amplifier overload - Short to ground on output Software-configurable signal processing including volume control, filters, compressor/limiting, delay, speaker equalization and output sensitivity CobraNet audio/control with dynamic use of available bundles over single Ethernet cable Dual Ethernet ports for redundancy Heavy duty removable terminal block connectors for speaker line connections Rotary switches for device identification EN certified, CE marked, UL listed, RoHS compliant Covered by Biamp Systems warranty The Vocia software provides the interface for configuring and programming the VA-4030(e) and VA-2060(e) amplifiers. The information supplied by this manual relates to hardware installation, physical connections and device and channel failover concerns. For more details on software setup, please consult the Vocia Software Help File. 3

5 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL System Indicators The LED indicators on the front panel of the amplifier provide information and operational status of the amplifier and its associated output and input channels. LED layout and features vary between amplifier models. LEDs are grouped to show chassis and amplifier channel status indication. Please see the Front Panel View section for details on the different configurations between the various amplifier models. Chassis Indicators Amplifier Chassis Indicators These indicators relate to the entire amplifier unit (chassis): AC power is a green LED indicator. This will illuminate when a AC Mains supply is applied to the unit. DC Power (VA-2060e and VA-4030e models only) is a green LED indicator. This illuminates when an auxiliary DC supply is applied to the unit via either or both 24V Auxiliary power inputs. Refer to the caution in the Rear Panel Auxiliary Power section. Amp Fault is a yellow LED that illuminates when a chassis fault has occurred. There are two types of chassis faults that can be reported, depending on the severity of the problem. Flashing yellow indicates a Warning, which means that some aspect of the amplifier chassis is not performing within normal specification. Audio may still be passing, but if the condition causing the Warning is not corrected, chassis failure may occur. Solid yellow indicates a fault, which means that some aspect of the amplifier chassis has failed and audio may no longer be passing through the device. Use Vocia software to determine the specific type of chassis warning or fault that has occurred. Activity is a tri-color LED that illuminates to show the configuration status of the device. If the LED is dark, the chassis has failed to boot or there is some other kind of fault. A solid green LED indicates that the unit is configured. A flashing yellow LED indicates the unit is active but not configured. A solid yellow LED indicates that the unit is configured and in standby. Standby only occurs when a unit has been designated as a redundant device when Device Failover is enabled. Status is a tri-color LED that indicates the health of the amplifier hardware. A green LED indicates the unit powered up normally. A flashing yellow LED is shown briefly during the power-up self test and should turn solid green upon successful start. A red LED indicates the unit experienced a problem during the power-up self test. 4

6 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL Channel Indicators Amp Channel Indicators These indicators relate to each amplifier channel: Amp Fault is a yellow LED that illuminates when a channel fault has occurred. Two types of channel faults can be reported depending on the severity of the problem. Flashing yellow indicates a Warning, which means that some aspect of the amplifier module is not performing within normal specification. Audio may still be passing, but if the condition causing the Warning is not corrected, channel failure may occur. Solid yellow indicates a fault, which means that some aspect of the amplifier module has failed and audio is no longer passing on that channel. Use Vocia software to determine the specific type of channel warning or fault that has occurred. Activity is a two-color LED that illuminates green when that channel is configured and actively passing audio and yellow when that channel is configured and in standby. Standby only occurs when a channel has been designated as redundant channel in a failover configuration. Signal is a tri-color LED that indicates audio signal presence on the amplifier channel. Green indicates the audio signal level is between -36 dbfs and -6 dbfs, yellow indicates a signal level between -6dBFS and -2 dbfs and red indicates clipping (above -2dBFS). Analog Input (VA-2060e and VA-4030e models only) is a tri-color LED that indicates audio signal presence on the amplifier analog Input channel. Green indicates the audio signal level is between -48 dbfs and -18 dbfs, yellow indicates a signal level between -18 dbfs and -2 dbfs and red indicates clipping (above -2dBFS). 5

7 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL VIEW VA-2060 VA-2060e VA-4030 VA-4030e 6

8 RISK OF ELECTRICAL SHOCK. DO NOT OPEN. VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Rear Panel BIAMP SYSTEMS assembled in the USA CPD-1401 N SJ CAUTION Model VA-4030e Analog Inputs Outputs V~ 50/60Hz GRN: Link / Active Ω 25V 70V 4Ω 100V 8Ω 25V 70V 4Ω 100V Load Select 8Ω 25V 70V 4Ω 100V 8Ω 25V 70V 4Ω 100V 60 Watts Auxiliary Power 24V DC 24V 0V 24V 0V 2 1 YEL: In Use / Conductor CobraNet Pri. Sec Page Active Relays MSB Device ID LSB C NC NO C NC NO C NC NO C NC NO Failover 2 1 Class 3 wiring: 100V setting Class 2 wiring: Ω, 8Ω, 25V and V setting 2 1 Conventions All numbered audio, relay and power connectors on the rear panel of the amplifier are configured with the lowest output or input on the right of the connector as viewed from the rear of the unit. AC Power Socket Provides for connection of the appropriate power cord. Each amplifier uses a switch mode power supply that has an operating voltage of V at 50/60 Hz. Auxiliary Power: Only available with VA-2060e and VA-4030e amplifiers. Caution: Due to potential energy hazard, connections to the Auxiliary Power 24V DC inputs must be made by a qualified electrician or other qualified person as required to conform with all local codes. This connection allows dual 24V DC power inputs to be used. Dual 24V DC supply capability allows the amplifier to meet standards that call for redundant power supplies. The DC supply must be wired into both power supply inputs, either from redundant supplies or from a single supply wired in parallel to the two inputs. If 24V is not supplied to both inputs, a loss-ofsupply fault will be reported. If a VA-4030e or VA-2060e amplifier is required to operate without a 24V supply, the Auxiliary supply fault monitoring must be disabled in Vocia software. A loss of supply fault is indicated via the Vocia software and by a blinking yellow Amp Fault indicator on the front panel of the affected device. The power supplies used for the amplifier must meet the voltage range and power requirements detailed in the specifications table below. Local standards, norms or codes may require the use of certified power supplies and may require observance of minimum on-battery running times both for standby and maximum power conditions. Note that dual redundant power supplies must each independently meet the total power requirements of the amplifier. The pluggable terminal blocks provided will accommodate wire sizes from AWG. External over-current protection must be provided, according to the current carrying capacity of the connecting wires, and in no case greater than 30 Amps. Do not ground or connect to chassis either the positive or negative Auxiliary Power connections. The Auxiliary power must be floating with respect to ground. Network Connections The amplifier is a CobraNet device. A Primary and Secondary CobraNet connection is provided for this. All CobraNet routing and bundle assignments are processed by the Vocia devices locally. Vocia makes dynamic use of available bundles in CobraNet. A 100Base-T Ethernet switch (not repeater hub) is required when networking multiple units. CobraNet utilizes standard CAT5, CAT5e, CAT6 or CAT7 cabling, which has a specified maximum length of 328 feet (100 meters). Additional Ethernet switches, or switches that provide fiber-optic interface, can be used to extend the physical distance between units within a network. Please note that CobraNet limits network extensions to seven hops (one-way transmissions) within a network. The CobraNet network connection is configured with the primary connector on the left and the secondary (redundant) connector on the right. The primary and secondary CobraNet ports are provided to facilitate connection redundancy. Each connector provides two LEDs that indicate Ethernet link and network activity. 7

9 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Table 1. CobraNet LED indication Left LED Right LED Description None None No data connectivity or CobraNet activity None Flashing Green Link Established. Typically seen on Secondary connection that is in standby. Amber Flashing Green Link established and CobraNet activity detected; unit acting as a CobraNet performer Flashing amber Flashing green Link established and CobraNet activity detected; unit acting as a CobraNet conductor Flashing amber None CobraNet fault; check cabling and configuration for errors Device ID switches The rotary ID switches are located on the back of the amplifier and give the unit a unique Device ID. The switches are in hexadecimal format. All Vocia units of the same type must have a unique Device ID to function properly within a Vocia Paging World (for instance, it is not possible to have two Vocia devices of the same type with the same Device ID of hex 07). Note that VA-4030 and VA-4030e units represent one device type, while VA-2060 and VA-2060e units represent another device type. As an example, to assign a Device ID of hex 07, leave the MSB switch on 0 and turn the LSB switch to 7. To create an ID of hex B7, turn the MSB switch to B and turn the LSB switch to 7. Device ID switches should be set using a 0.1 inch (2.5mm) to 0.12 inch (3.0mm) flat blade screwdriver. More information on setting IDs and the hexadecimal numbering scheme used can be found in the Vocia Software Help File. Analog Audio Inputs with Phantom Power Option For the VA-2060e and VA-4030e, each amplifier channel has analog inputs that allow a local balanced microphone or line level background source to be delivered to the amplifier channel associated with that input. Two such inputs are available on the VA-2060e amplifier and four on the VA-4030e. Input sensitivity and 48V phantom power on/off state may be determined in the Vocia software. Because a local input may only be delivered to the channel associated with that input, if a local background source is required on two or more channels the source must be wired in parallel to each of the inputs. An exception is that if two or more channels of an amplifier are configured in software as a group or multi-way, the lowest local input channel number will be presented to all channels. For instance, if a VA-4030 is deployed with channels 2, 3 and 4 configured as a group or 3-way multi-way, local input 2 will be presented to outputs 2, 3 and 4. Page Active Relay Page Active Relays (PAR) are available on all amplifiers. Via the Page Active Relay connectors, one Form C (single pole, changeover) relay is presented per channel for the VA-4030 and VA-4030e. Similarly, two such relays per channel are presented for the VA-2060 and VA-2060e (relays operate in tandem). Each PAR connector is a six-way 3.5mm pluggable screw terminal block. The PAR connections are labeled as follows: C: Relay Common NC: Normally Closed NO: Normally Open Page Active Relay: VA-4030e and VA-2060e 8

10 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Amplifier Output Connections CAUTION: All speaker wiring connections and output load selection should be made by qualified personnel and with the amplifier power removed. The 100V output requires Class 3 wiring. Please refer to a qualified electrician or other qualified person according to local codes. Transformer Load Selection The required amplifier output load is configured via the use of a recessed indented selector above the amplifier speaker output connectors. The switch is designed to be operated with a flat blade screwdriver (blade width / 2.5mm - 6.4mm). Selection can be made between 4 or 8Ω for Low Impedance connections and 25V, 70V or 100V for Constant Voltage loads. By default, the amplifier factory default setting is 8Ω. Do not operate the amplifier with no speaker load. If an amplifier channel is unused (i.e., has no load) do not configure the channel in Vocia software to pass audio. Speaker Connection To minimize power loss, use a speaker cable of appropriate gauge for the load impedance. For long speaker cables, to minimize high frequency loss, choose a low capacitance cable. Use the supplied plug-in barrier strip connectors to connect loudspeaker level outputs. If stranded speaker wire is used, be sure to incorporate all strands into the connector, as stray strands can short to the adjacent terminal or chassis. Do not leave excessive bare wire outside the terminals, as this can lead to shorts. Use of the supplied cable restraints is required to secure the cable in the connector. To facilitate parallel wiring, each connector allows for the connection of two loads to each amplifier channel. Two four-way connectors are available on the VA-2060 and VA-2060e amplifier and four connectors are available on the VA-4030 and VA-4030e amplifier. Rated Load Table: The total output load connected to any channel must not be less than the rated impedance load for that channel, as detailed below. Operating the amplifier in excessive overload may cause power supply safety limiting. 4Ω Setting 8Ω Setting 25V Setting 70V Setting 100V Setting VA-4030 and VA-4030e 4Ω 8Ω 20.8Ω 163.3Ω 333.3Ω VA-2060 and VA-2060e 4Ω 8Ω 10.4Ω 81.7Ω 166.7Ω 9

11 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Output Fault Detection The Amplifier monitors (supervises) for faults on speaker connections using a combination multiple out-of-band (inaudible) high frequency tones for end-of-line detection, and DC current for ground fault detection. For end-of-line detection, one or more (up to 15 maximum) ELD-1 units must be connected to the end/s of the speaker line. End-of-line and ground fault detection may be individually enabled/disabled in the Vocia software. To ensure correct operation of fault detection it is necessary to follow these guidelines: When an ELD-1 is being used in a Vocia system it is important that the Amplifier Output Setting in the software matches the Hardware Output setting selected on the physical amplifier (8Ω, 4Ω, 25V, 70V or 100V). See the Software Help file for more information. Recorded audio messages or audio content with continuous or swept tonal components (e.g. alert tones) and any content with significant high frequency harmonic content should be band limited (>24dB/octave) at 15 khz during recording. Note that program content that is distorted due to poor recording techniques may contain excessive high frequency harmonics. Signal level adjustments within a Vocia system should be set so as to minimize clipping. Severely clipped signals may also affect the out-of-band fault detection tones. The use of speaker cables that inherently attenuate high frequencies is not supported (e.g. screened cables). Speaker cables must maintain frequency response to the end of line of less than 20kHz at with respect to 1kHz. Speaker cables longer than 500 feet may prevent correct operation of ELD and Ground Fault monitoring capabilities. An advantage of Vocia is that amplifiers may be easily distributed close to speakers, thereby minimizing long runs of expensive and potentially lossy speaker cable. Highly capacitive speaker lines or loads may prevent correct operation of the ELD detection system. Legacy monitored speaker circuits that use capacitors and resistors or similar methods must have all legacy monitoring circuitry removed for correct operation of the ELD detection system. The amplifiers use DC current to detect whether there is an erroneous ground connection placed on either or both speaker wires. The detection circuit will declare a fault for a resistance to ground of 50kΩ or less. To prevent false ground fault readings, the DC resistance to ground of speaker circuits must be 100kΩ or higher (either speaker wire to ground). For EN54-16 compliance, one or more ELD units must be fitted. End of Line detection and Ground Fault Detection must be enabled in the Vocia software. 10

12 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FAILOVER MODES Failover Modes The Vocia amplifiers support a device-to-device or channel-to-channel failover mode. Only one type of failover mode can be implemented per amplifier. Device-to-Device Failover All amplifiers support device-to-device amplifier chassis failover in case of fault. The redundant amplifier must be the same model as the primary amplifier. A Failover Link Cable must be connected between the primary and redundant amplifier as shown below. Connect ground to ground and Pin 1 of the primary amplifier to Pin 2 of the redundant amplifier; connect Pin 2 of the primary amplifier to Pin 1 of the redundant amplifier. Failover is triggered by one of the following conditions: Chassis fault on primary amplifier Channel fault on primary amplifier Loss of power to the primary amplifier Loss of CobraNet link to primary amplifier Loss of Failover Link Cable ELD-1/speaker line fault if enabled in software Only faults (chassis and channel) trigger the failover mechanism. Abnormal conditions that do not immediately impair audio appear as warnings, but do not trigger failover. The redundant amplifier may be wired in parallel to the existing speaker line or it can be connected to a redundant speaker line. Relays isolate the output terminals on the secondary amplifier unit. Relays are normally open. When a configuration is received, relays close on the primary unit and remain open on the redundant unit. On failover, the relay states are reversed. Device-to-Device Failover Wiring with Parallel Speaker Wiring After replacing the faulty amplifier, a power cycle is required to recover from failover. This can be done either by physically repowering the amplifiers or by performing a device reset in the Vocia software via the amplifier test tab. The amplifiers are required to be reset within 10 seconds of each other in order for the primary device to resume control. 11

13 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FAILOVER MODES Channel-to-Channel Failover All amplifiers support channel-to-channel failover. This is configured in the Vocia software in the amplifiers general setting as 1:1 Failover. In this configuration, channel pairs can be specified and adjacent channels will act as a redundant backup. Channel 2 will act as backup for channel 1. For the VA-4030 and VA-4030e models, channel 4 will act as backup for channel 3. Additionally the VA-4030 and VA-4030e amplifiers support 3:1 channel redundancy. This is configured in the Vocia software in the amplifiers general setting as 3:1 failover. In this configuration channel 4 will act as a redundant backup for channel 1, 2 or 3. 1:1 or 3:1 channel failover is triggered by one of the following conditions: Heatsink fault (over temperature) Short circuit fault Channel failure fault ELD-1/speaker line fault if enabled in software The redundant channel may be wired in parallel to the existing speaker line or connected to a redundant speaker line. The primary amplifier module will resume control after the fault condition is cleared and the unit is re-powered. Channel-to-Channel Example: Parallel Wiring and Redundant Speaker Topology 3:1 Failover Speaker Wiring 12

14 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e SPECIFICATIONS Vocia Amplifier 2060 / 2060e / 4030 / 4030e SPECIFICATIONS Message Memory: Network Audio: Network Connections: Analog Inputs: Nominal Input Range: Maximum Input Level: Equivalent Input Noise: Dynamic Range: Input Impedance: Phantom Power: Frequency Response: Signal to Noise Ratio: THD + Noise: Rated Output Power: VA-2060: VA-2060e: VA-4030: VA-4030e: Supported Loads: Low Impedance: Constant Voltage: Output Configuration: Output DC Offset: PAR Relays Form: Max Operating Voltage: Max Operating Current: MB 20-bits, 48kHz, 5-1/3 ms (fixed) RJ45 with shielded Ethernet cable (CAT5, CAT5e, CAT6 or CAT 7) (VA-2060e and VA-4030e) Per Channel -66dBu to 0dBu +24dBu (max Gain) >-125dbu >94dB 8kΩ +48V DC 40Hz-20kHz +/- 2dB >88dB, unweighted <0.5% 50Hz-100Hz <0.3% 100Hz-10kHz 2x 60W RMS, total 120W 2x 60W RMS, total 120W 4x 30W RMS, total 120W 4x 30W RMS, total 120W 4Ω, 8Ω 25V, 70V or 100V Transformer Coupled (ground free) <100mV Single Form C contact 125V AC, 60V DC 100mA AC, 1A DC Power: AC (all amplifiers): DC (VA-2060e and VA-4030e): Continuous power rating Peak Power rating DC Range: Overall Dimensions: Height: Width: Depth: Weight: VA-2060: VA-2060e: VA- 4030: VA- 4030e: Compliance: 100V-240V AC, 50H 60 Hz Nominal 24V DC 60 Watts 150 Watts 18V-30V; <100mV Ripple 3.25 in (82.5mm) 19 in (483mm) 14.2 in (360mm) 24.7lbs (11.2kg) 24.9lbs (11.3kg) 26.0lbs (11.8kg) 26.2lbs (11.9kg) FCC Part 15B EN certified UL and C-UL listed CCC pending C-Tick RoHS Directive 2002/95/EC EN 60849, AS verified Environment Ambient Operating Temperature Range: degrees F (-8 42 C) Ambient Intake: Humidity: 0 100% non-condensing Altitude: 0 10,000 Feet MSL 13

15 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e BLOCK DIAGRAM 4030e and 2060e Amplifiers 4030 and 2060 Amplifiers 14

16 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e CURRENT DRAW AND HEAT OUTPUT VA-4030 and VA-4030e Specifications Total Output Power (Watts) Channels Used IDLE Input Power Watts BTU /hr 1/8 POWER PINK NOISE Input Power Watts BTU /hr 1/3 POWER PINK NOISE Input Power Watts BTU /hr FULL POWER SINE WAVE Input Power Watts BTU /hr VA-2060 and VA-2060e Specifications Total Output Power (Watts) Channels Used IDLE Input Power Watts BTU /hr 1/8 POWER PINK NOISE Input Power Watts BTU /hr 1/3 POWER PINK NOISE Input Power Watts BTU /hr FULL POWER SINE WAVE Input Power Watts BTU /hr 15

17 VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. 2 If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. 3. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems recommendations. 4. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. All server-based devices are warranted for 3 years only. 5. This warranty is in lieu of all other warranties, expressed or implied. BIAMP Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. 6. The remedies set forth herein shall be the purchaser s sole and exclusive remedies with respect to any defective product. 7. No agent, employee, distributor or dealer of BIAMP Systems is authorized to modify this warranty or to make additional warranties on behalf of BIAMP Systems. Statements, representations or warranties made by any dealer do not constitute warranties by BIAMP Systems. BIAMP Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person. 8. No action for breach of this warranty may be commenced more than one year after the expiration of this warranty. 9. BIAMP Systems shall not be liable for special, indirect, incidental, or consequential damages, including lost profits or loss of use arising out of the purchase, sale, or use of the products, even if BIAMP Systems was advised of the possibility of such damages _ C 16

18 FCC COMPLIANCE FCC NOTICE - CLASS B DIGITAL DEVICE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential as well as in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and receiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected or 4) Consult the dealer or an experienced radio/tv technician for help. 17

19 COMPLIANCE DoC VA EC Declaration of Conformity Biamp Systems Corporation, as manufacturer having sole responsibility, hereby declares that the following described product complies with the applicable provisions of the DIRECTIVES below except as noted herein. Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration. Product Models: Vocia Amplifier, VA-2060, -2060e, -4030, -4030e Product Description: Applicable EC Directives: Networked Audio Amplifier Applicable Harmonized Standards: LVD Directive (2006/95/EC) Safety EN 60065:2002 EMC Directive (2004/108/EC) Emissions EN :1996, Environment E2 Immunity EN : 1996, Environment E2 Special Considerations for Product Environment or Compliance: Shielded cabling must be used for system connections. Technical Documentation File, Location and Contact: Biamp Systems Corporation phone: (503) S.W. Gemini Drive fax: (503) Beaverton, OR USA Authorized Representative: Larry Copley, Compliance Engineer Authorized Signature: I ssued: June 2011! 18

20 COMPLIANCE RoHS COMPLIANT This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directives 2002/95/EC of January 27, 2003, and 2005/618/EC of August 18, 2005, the EU RoHS Directives. An EU RoHS Materials Content Declaration document may be obtained at (This information is presented to comply with the requirements of Chinese law SJ/T )!"#$% (Hazardous Substances Table) Biamp Systems Corporation &'()*+,-./, (Digital Signal Processor and Amplifier) Vocia VA-2060, VA-2060e, VA-4030, VA-4030e Pb 6!"!#$$45% (Substances) Hg Cd Cr+6 PBB PBDE 7 8 9:; 0123 (Part Name) <=>?!(Equipment Chassis)! X O X O O (Power Cord) O O O O O O CDEFBGH (Plug-in Terminal Blocks) O O O O O O IJ(CD ROM) O O O O O O KLMNOPQRS (Manual and Paper Documents) O O O O O O TU?MV!TUWX (Box and Packing Materials) O O O O O O! 0Y%Z[01V!\$WX]^_`!a!"#$bc SJ/T ^defg. XY%Z[01]hi!j`\$WXVk^_`!a!"#$lc SJ/T ^defg. m@nomp4qr8vk^\$wx]s8tnuv#^kwxyz{ 0.01%s }~Ä 91/338/EECpÅÇ}~Ä 76/769/EECqdeÉÑMÖÜáàâä#$Meã0å]Vçé^Üèêë myíj`4ì`#$vk^\$wx]s6tnuv#^kwxyz{ 0.1%: 2) 6móW]òôöj`võ5úskwxù 0.35% 3) 6mûW]òôöj`võ5úskwxù 0.4% 4) 6müW]òôöj`võ5úskwxù 4% 5) l X]^6p 6Xvõs6kwz{ 85%q 01ñ^6 7) ß `y 5ú ^ X]Vk^6sÜc F ÆMØ*+,TUsN] 6^kwz{ 80% bc 85% 8) ± F ñ^6 9) &'()*'+, -().µ π /0 123 X]4 m ªÖܺΩís]æø ÖÜ dö 10 s 1òY øƒ ö 0-40C ( F) «ö 0-95%s» ÀDl ö 0-10,000 ÃÕ Œœ! 4NO ÿÿ Vac, 50/60 Hz, 60W 01! p 01± fi+q