CONTROL PANEL FOR 24 V GEARMOTORS 319V21EN INSTALLATION MANUAL ZL92. English

Size: px
Start display at page:

Download "CONTROL PANEL FOR 24 V GEARMOTORS 319V21EN INSTALLATION MANUAL ZL92. English"

Transcription

1 319V21EN CONTROL PANEL FOR 24 V GEARMOTORS INSTALLATION MANUAL ZL92 Englsh EN

2 Foreword Use of the products must be restrcted to ts ntended use (.e. that for whch t was expressly bult for). Any other use s to be consdered dangerous. Came Cancell Automatc S.p.A. s not lable for any damage resultng from mproper, wrongful or unreasonable use Keep these warnngs wth the nstallaton and use manuals ssued wth the automated system. Before nstallng (prelmnary check: n case of a negatve outcome, do not proceed before havng compled wth the safety oblgatons) Make sure that the parts you ntend to automate are n good workng order, and that they are properly balanced and algned. Also, make sure that proper mechancal stops are already n place If the operator wll be nstalled at a heght of less than 2.5 m from the ground or other access level, check whether you wll need any protectons and/or warnngs Any gate leaves, f tted wth pedestran entrances, onto whch you wll nstall an operator, must have a blockng mechansm when the gate s n moton Make sure that the openng of the automated gate s not an entrapment hazard as regards any surroundng f xed parts Do not mount the operator upsde down or onto any elements that may fold under ts weght. If needed, add sutable renforcements at the ponts where t s secured Do not nstall onto gates on ether an upward or downward slope (.e. that are not on fl at, level ground) Check that any lawn waterng devces wll not wet the gearmotor from the bottom up. Installaton Carefully secton off the entre ste to prevent unauthorsed access, especally by mnors and chldren Be careful when handlng operators that wegh more than 2 Kg (see nstallaton manual). In such cases, employ proper weght handlng safety equpment All openng commands (e.g. buttons, key selectors, magnetc detectors, etc.) must be nstalled at least 1.85 m from the gate s area of operaton permeter - or where they cannot be reached from the outsde of the gate. Also, the drect commands (e.g. push button, or proxmty devces, etc.) must be nstalled at a heght of at least 1.5 m and must not be accessble to the publc All mantaned acton commands, must be placed where the movng gate leaves, transt areas and drveways are completely vsble If mssng, apply a permanent label that shows the poston of the release mechansm Before delverng to the clent, verfy that the system s EN (mpact test) standard complant. Make sure that the operator has been properly adjusted and that the safety and protecton devces, as well as the manual release WARNING! Important nstructons for the safety of people: READ CAREFULLY! are workng properly Where necessary and n plan sght, apply the Warnng Sngs (e.g. gate plate). Specal nstructons and advce for users Keep the gate s area of operaton clean and clear of any obstacles. Trm any vegetaton that may nterfere wth the photocells Do not allow chldren to play wth the f xed command devces, or n the gate s area of operaton. Keep any remote control devces (.e. transmtters) away from the chldren as well Frequently check the system, to see whether any anomales or sgns of wear and tear appear on the movng parts, on the component parts, on the securng ponts, on the cables and any accessble connectons. Keep any jonts (.e. hnges) lubrcated and clean, and do the same where frcton may occur (.e. slde rals) Perform functonal tests on photocells and senstve edges, every sx months. Keep glass panels constantly clean (use a slghtly water-mostened cloth; do not use solvents or any other chemcal products) If the system requres repars or modf catons, release the operator and do not use t untl safety condtons have been restored Cut off the power supply before releasng the operator for manual openngs. See nstructons Users are FORBIDDEN to carry out ANY ACTIONS THAT THEY HAVE NOT BEEN EXPRESSLY ASKED TO DO OR SO INDICATED n the manuals. Any repars, modf catons to the settngs and extraordnary mantenance MUST BE DONE BY THE TECHNICAL ASSISTANCE STAFF On the perodc mantenance log, note down the checks you have done. Specal nstructons and advce for all Avod workng near the hnges or movng mechancal parts Stay clear of the gate s area of operaton when n moton Do not resst the drecton of movement of the gate; ths may present a safety hazard At all tmes be extremely careful about dangerous ponts that must be ndcated by proper pctograms and/or black and yellow strpes When usng a selector or command n mantaned acton mode, keep checkng that there are no people n the area of operaton of the movng parts. Do ths untl you release the command The gate may move at any tme wthout warnng Always cut the power when cleanng performng mantenance. P. 2 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

3 Legend of symbols Ths symbol shows whch parts need to be read carefully. Ths symbol shows whch parts have to do wth safety. Ths symbol shows what to tell end users. Intended use and lmtatons of use Intended use The ZL92 control panel s engneered to command 24 V DC operators for swng gates of the STYLO, MYTO, FROG-J and AMICO seres. Any nstallaton and use other than that explaned n ths manual are forbdden. P. 3 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. Lmtatons to use Follow all cable dstance and dameter nstructons as shown n the table Cable type and secton The overall power of the motors must not exceed 3 W. Descrpton Engneered and manufactured entrely by CAME Cancell Automatc S.p.A.. The control panel s powered by 23 V AC, wth 5 / 6 Hz frequency. The command devces and accessores work on 24 V. Warnng! The accessores must not exceed 5 W overall. The transformers are ftted wth a protecton that keep the gate leafs open even when overheatng. The leafs are closed only after the temperature falls below overheatng threshold. All connectons are protected by quck fuses, see table. Functons on the nput and output contacts, tme adjustments and user management, are all handled va the dsplay and managed by the software. It s set up to ft the LB9 card whch provdes power to the electrcal board va emergency batteres, whch are n turn automatcally trggered durng power outages. When the lne current returns, t recharges the batteres. Techncal data TECHNICAL DATA Power supply Maxmum rated power Power draw when dle Maxmum power for 24 V accessores Insulaton class of the crcuts Contaner materal Contaner protecton ratng Workng temperature Dmensons (mm) 23 V - 5/6 Hz 3 W 11 ma 5 W II ABS IP54-2 / +55 C to protect: Electronc lne card FUSE TABLE fuse rated to: 3.15 A-F = 12 V 1.6 A-F = 23 V 24 V accessores 2 -F Command devce (control panel) 1 A-F Motor 1 / Motor2 Replacement code (fuse) 6.3 A =25 V Ø6,3x22 UFG RIR316

4 Man component parts 1 -Transformer 2 -Card fuse 3 -Accessores fuse 4 -Dsplay 5 -Memory roll card connector 6 -AF card connector 7 -R7 or R8 card connector 8 -Lack of calbraton warnng LED ndcator 9 -Programmng buttons 1 -Termnal boards V power termnal boards 12 -Lne fuse 13 -Current on-lne warnng LED ndcator 14 -Motor 1 fuse 15 -Motor 2 fuse 16 -Antenna connecton termnal board 17 -Thermal termnal board 14 Warnng! Before dong any work on the control panel, make sure to cut off the man current or dsconnect the batteres. Installaton Prelmnary checks V 17V V Installaton must be done by qualfed, expert staff and n full complance wth current laws and regulatons. Before nstallng, do the followng: Check that the control panel s anchored to a sold surface whch s protected from possble mpacts, and that the nuts, bolts, wall plugs, etc., are sutable for the job. Make sure you have a sutable omnpolar cut-off devce wth contacts more than 3 mm apart, and ndependent (sectoned off) power supply. Make sure that any connectons nsde the box (that provde contnuance to the protectve crcut) are ftted wth extra nsulaton as compared to the other conductve parts nsde. Set up proper ppes and conduts for electrcal cables to pass through, makng sure these are protected from mechancal damage. 23V P. 4 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

5 Tools and equpment Make sure you have all of the tools and materals you wll need to proceed wth the nstallaton n total safety, accordng to current rules and regulatons. Here are some examples. P. 5 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. Anchorng and mountng the box 1) Secure the base of the panel to a protected area; we suggest usng cross slot Phllps head bolts of max. 6 mm n dameter. 3) Assemble the pressure hnges. 5) Snap the hnge covers nto place.!! 2) Perforate the pre-punched holes and nsert the cable glands wth the corrugated tubng for the electrcal cables to travel through. N.B.: dameter of the pre-punched holes: 2 mm. 4) Insert the hnges nto the box (ether on the rght or left sde, as you prefer) and secure them usng the suppled nuts and bolts. 15 mm~ Slde the hnges so they can rotate. 6) After any calbratons and adjustments, secure the cover usng the suppled screws.

6 Electrcal connectons Cable types and sectons Connectons Control panel power supply N.B.: If the cable length dffers from that specfed n the table, then you must determne the proper cable dameter based on the actual power draw from the connected devces and accordng to the CEI EN standards. For connectons that requre several, sequental loads, the szes gven on the table must be re-evaluated based on actual power draw and dstances. When connectng products that are not specfed n ths manual, please follow the documentaton provded wth sad products. AMICO FROG-J STYLO ME MYTO ME Type of cable L M1 N1 ENC1 EB1 V1 M2 N2 ENC2 EB2 V2 STYLO RME M1 N1 ENC1 EB1 V1 Length of cable 1 < 1 m + - STYLO RME M2 N2 ENC2 EB2 V2 Length of cable 1 < 2 m Length of cable 2 < 3 m 3G x 1,5 mm 2 3G x 1,5 mm 2 3G x 2,5 mm 2 Power supply to motor* wth encoder 3G x 1,5 mm 2 3G x 1,5 mm 2 3G x 2,5 mm 2 Power supply to motor**wth encoder 4G x 1,5 mm FROR CEI 4G x 1,5 mm 2 4G x 2,5 mm 2 Flashng lght x 1,5 mm 2 2 x 1,5 mm 2 2 x 1,5 mm 2 Photocell transmtters Photocell recevers CEI EN x,5 mm 2 4 x,5 mm 2 2 x.5 mm 2 4 x,5 mm 2 2 x,5 mm 2 4 x,5 mm 2 Power supply to accessores 2 x,5 mm 2 2 x,5 mm 2 2 x 1 mm 2 Command and safety devces 2 x,5 mm 2 2 x,5 mm 2 2 x,5 mm 2 Antenna connecton RG58 Maxmum 1 m * MYTO ME - FROG J - AMICO - STYLO RME / ** STYLO ME Power source and accessores Power supply 23 V AC frequency 5/6 Hz 12 V 15 W maxmum, Electro-lock for the Myto, Frog-J, Amco and Stylo RME motors Possble second 12 V 1 W max. electrolock for the Myto, Frog-J, Amco and Stylo RME motors Gearmotor M1 24 V DC gearmotor featurng delayed acton on openng Termnals for powerng the followng accessores: - 24 V AC, DC Overall power allowed: 5 W Possble output of the rado recever s second channel (N.O. socket). Max. socket ratng: 5 ma 24 V DC. M2-24V DC gearmotor featurng delayed acton on closng MYTO ME AMICO FROG-J STYLO ME P. 6 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

7 CANCELLI AUTOMATICI CANCELLI AUTOMATICI Command devces 1S7 Keypad selector N.B. : nsert the (R8) decoder card to have the (S7) keypad selector recognsed. R8 P. 7 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. 1LT1 - Magnetc card reader ACCESS CONTROL Stop button (N.C. contact) - Button to stop gate whle excludng the automatc closng cycle. For movement to resume you must press the command button or transmtter button. N.B.: f the contact s unused, select = (Dsabled) from the F1 functons menu. Key selector and/or openng button (N.O. contact) - Gate openng command. Key selector and/or partal openng button (N.O. contact) - Partal gate openng for pedestran access. Key selector and/or closng button (N.O. contact) - Gate closng command. Key selector and/or commands button (N.O. contact) - Commands for openng and closng the gate pressng the button or turnng the key-swtch, nverts the gate s movement or stops t dependng on how t s set on the 2-7 command n the FUNCTIONS menu. 1TSP - Transponder sensor CAME Red Black A B N.B. : nsert the (R7) decoder card to have the (TSP) sensor or (LT1) card reader recognsed. S1 GND Antenna wth RG58 cable for the remote control. R7

8 Warnng devces Flashng lght (socket ratng: 24 V DC - 25 W max.) It flashes durng openng and closng phases of leaf. Safety devces Courtesy or cycle lght (contact rated up to: 24V 25 W max.) auxlary connecton of an outdoor lamp that can be freely postoned, for addtonal lghtng of the drveway. Cycle lght: It stays on from the moment the gate begns openng untl t s fully closed (ncludng the automatc closng tme). Courtesy lght: Stays on for a fxed tme perod (see functon F25 ). Conf gure ether (N.C.) contacts CX or CY, nput for EN complant safety devces such as photocells. See CX (F2 Functon) or CY(F3 Functon) nput functons n: - C1 «re-open durng closng phase», when the gate leaf s closng, openng the contact trggers the nverson of the drecton of movement untl the gate leaf s fully open. - C2 «re-close durng openng phase», when the gate leaf s openng, f the contact s opened t trggers an nverson of the drecton untl gate leaf s fully closed; - C3 «partal stop», halts movng gate leaves and causes them to automatcally close (f ths functons has been selected); - C4 «stand-by obstacle», stops the movng gate leaves causng them to start movng agan once obstacle s removed. N.B. : f CX and CY contacts are unused they need to be deactvated durng programmng. RX RX DIR photocells Open gate ndcator-lght (Socket ratng: 24 V 3 W max.). It turns on when the gate s open. It turns off when the gate s closed (see functon F1 ). DELTA photocells DELTA-S photocells TX TX P. 8 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

9 Conf gure ether (N.C.) contacts CX or CY, nput for safety devces such as sensate edges, that comply wth EN standards. See CX (F2 Functon) or CY(F3 Functon) nput functons n: DF DF wth montorng card for DFI connectons. P. 9 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. - C7 «re-open whle closng», durng gate closng, openng the contact causes nverson of movement untl gate s fully open; - C8 «re-close whle openng», durng gate openng, openng the contact causes nverson of movement untl gate s fully close. N.B. : f CX and CY contacts are unused they need to be deactvated durng programmng. Electrcal connecton for runnng the photocells safety test DOC / DELTA DIR / DELTA S At each openng and closng command, the control board assesses the eff cency status of the safety devces (photocells). Any anomaly found s sgnaled wth the fl ashng of the LED on the control board. Consequently t cancels any commands comng from the transmtter or the button. Electrcal connecton to enable the photocell safety test: - the transmtter and the recever, must be connected as per the dagram; - from the F5 functon select whch nputs to run the safety test on.

10 Programmng Descrpton of commands F I Dsplay Navgazone menu < < The ESC key s for: - extng the menu; - cancellng modfcatons. The < keys are for: - shftng from one menu tem to another; - ncrease or decrease values. To enter the menu, keep the key pressed for at least one second. To ncrease or reduce values, use the greater than-lesser than keys... Even for the submenus, use the greater than-lesser than arrows To ncrease or reduce values, use the greater than-lesser than keys... { ESC < < ESC F { { F F 2 F N.B.: when the menu s actve, the system cannot be used....to ext the menu, wat 1 seconds, or press ESC,. The key s for: - enterng the menu; - confrmng and memorsng set value....then press...then press then press to confrm P. 1 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

11 Menu structure P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F 1 Total stop Functon F 2 functon assgned to CX nput F 3 functon assgned to CY nput F 5 Safety test functon F 6 mantaned acton functon F 7 Command mode on 2-7 F 8 Command mode on 2-3p F 9 Obstacle detecton functon when motor s stopped F 1 Warnng lght functon F 11 Exclude Encoder functon F 12 Slow start functon F 13 Closng thrust functon F 14 Sensor type selector functon F 16 Ram head blow functon (only for Myto Amco Frog J - Stylo RME motors) F 17 Lock functon (only for Myto Amco Frog J - Stylo RME motors) F 18 Supplementary lght functon F 19 Automatc closng tme F 2 Automatc closng tme after partal openng F 21 pre-flashng tme F 22 Workng tme F 23 Delay openng tme F 24 Delay closng tme F 25 Courtesy lght tme F 26 Ram head blow tme (only for Myto Amco Frog J - Stylo RME motors) F 27 lock tme (only for Myto Amco Frog J - Stylo RME motors) F 28 M1 motor speed adjustment F 29 M2 motor speed adjustment F 3 M1 motor speed slow-down tme adjustment F 31 M2 motor speed slow-down tme adjustment F 32 Addtonal closng slow down adjustment for M1 and M2 motors (only for Myto and Stylo wth straght-arms) F 33 Calbraton speed adjustment F 34 Senstvty durng movement F 35 Senstvty durng slow-downs F 36 Adjustng partal openngs F 37 Adjustng the ntal slow-down pont of the M1 motor when openng F 38 Adjustng the ntal slow-down pont of the M1 motor when closng F 39 Adjustng the pont the M1 motor begns drawng to the fully open poston F 4 Adjustng the pont the M1 motor begns drawng to the fully closed poston F 41 Adjustng the ntal slow-down pont of the M2 motor when openng F 42 Adjustng the ntal slow-down pont of the M2 motor when closng F 43 Adjustng the ntal drawng to stop pont of the M2 motor when openng F 44 Adjustng the ntal drawng to stop pont of the M2 motor when closng F 45 Adjustng an addtonal slow-down pont when closng (only for Myto and Stylo RME wth straght-arms) F 46 Adjustng the number of motors F 5 Savng data n memory roll F 51 Readng memory roll data U 1 Type of command to assocate to a user va rado command U 2 Cancellng sngle users U 3 Cancellng all user A 1 Settng the type of gearmotor A 2 Motor tests A 3 Gate run calbraton A 4 Resettng parameters H 1 Software verson

12 IMPORTANT! Before settng adjustng any functons, set whch gearmotors are nstalled n the system (A 1 Motor type), check the gate s proper drecton of travel of (A 2 Motors test) and calbrate the gate run (A 3 Gate run calbraton) Note: press to confrm after choosng each functon value. Motors test and calbraton menu A 1 (Motor type) : settng up the type of swng gate gearmotor nstalled. 1 = Stylo ME wth jonted-arm; 2 = Stylo ME wth straght arm; 3 = Myto; 4 = Frog-J; 5 = Amco; 6 = Stylo RME wth jonted-arm; 7 = Stylo RME wth straght arm F A I A 2 (motors test) : actvatng the test to verfy the proper turnng drecton of the gearmotors (see motors test paragraph). = Deactvated; 1 = Actvated. F A 2 A 3 (Calbratng the gate run) : automatc calbraton of the gate run on both gearmotors (see gate run calbraton paragraph). = Deactvated; 1 = Actvated F A 3 A 4 (Reset parameters): data resettng (default settng) and cancellng the gate run calbraton. = Deactvated; 1 = Actvated. F A P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

13 Functons menu F 1 (Total Stop) : ths functon stops the gate and consequently excludes any automatc closng cycle; for movement to resume, you need to use the keypad or transmtter. Insert the safety devce on [1-2]; f unused, select functon. = Deactvated; 1 = Actvated (default settng) P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F F 2 (CX nput): the N.C. safety contact nput can take on the followng functons: C1 (re-openng when closng), C2 (re-closng when openng), C3 (partal stop), C4 (obstacle stall), C7 (re-openng when closng, for senstve edges), C8 (re-closng when openng, for senstve edges) or, be deactvated. See safety devces on electrcal connectons. = Deactvated (default settng); 1 = C1; 2 = C2; 3 = C3; 4 = C4; 7 = C7; 8 = C8. F F 2 F F 3 F F 5 F 3 (CY Input): safety contact nput can take on the followng functons: C1 (re-openng when closng), C2 (re-closng when openng), C3 (partal stop), C4 (obstacle stall), C7 (re-openng when closng, for senstve edges), C8 (re-closng when openng, for senstve edges) or, be deactvated. See safety devces on electrcal connectons. = Deactvated (default settng); 1 = C1; 2 = C2; 3 = C3; 4 = C4; 7 = C7; 8 = C8. F 5 (Safety Test) : allows the card to check the effcency of any safety devces (.e. photocells) after every openng or closng command. = Deactvated (default settng); 1 = CX; 2 = CY; 3 = CX+CY F 6 (Mantaned acton) : the gate works by keepng the button pressed (button 2-3 for openng, button 2-4 for closng, or f set to the Closng functon, only wth button 2-4. (Ths excludes all other command devces ncludng rado commands). = Deactvated (default settng); 1 = Actvated. F F

14 F 7 (2-7Command) : settng the contact on 2-7 to step-by-step (open-close) or sequental (open-stop-close-stop). = step-by-step (default settng); 1 = sequental. F F 7 F 8 (2-3P Command) : settng the 2-3P contact to pedestran openng (second gate leaf opens fully) or partal (second gate leaf opens partally dependng on the tme settng of the percentage between 1 and 8 of the gate run, functon F36 ). = pedestran openng (default settng); 1 = partal settng. F F 8 F 9 (Obstacle detecton) : when motor s stopped (gate closed or after a total stop command) t prevents any movement f safety devces, such as photocells, detect any obstacles. = Deactvated (default settng); 1 = Actvated. F F 9 F 1 (Openng Warnng lght) : lght bulb connected on 1-5, warns of gate status. = gate open and movng, stays on (default settng) F F F 11 (Exclude Encoder): excludes encoder from managng slow-downs, obstacle detecton and senstvty. = Encoder actvated (default settng); 1 = Encoder deactvated. F F F 12 (Slowed-down thrust): at each openng or closng command, the gate leaves move slower for a few seconds. = Deactvated (default settng), 1 = Actvated. F F 2 1 = - gate openng, flashes on and off every half second; - gate closng, flashes on and off every second; - gate open, stays on; - gate closed, stays off. P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

15 F 13 (closng thrust) : at the closng endpont, the gearmotors gve the gate leaves a bref fnal-closng thrust. = Deactvate (default settng); 1 = 1. = Mnmum thrust 2. = Medum thrust 3. = Maxmum thrust F F P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F 14 (Type of sensor) : settng the type of sensor for the operator command va (TSP) transponder or (LT1) magnetc card reader wth R7 encoder card or S7 keyboard wth R8 encoder card. = TAG; 1 = S7 (default settng). F F 4 F 16 (Ram head blow): before any openng run, the gate leaves wll press onto the mechancal endstop for a few seconds, to help release the electro-lock (to set the tme, see F26 ). Note: ths functon s only vsble for the Myto, Frog.J, Stylo-RME and Amco gearmotors. = Deactvate (default settng); 1 = Actvate. F F 6 F 17 (Lock): releasng the electrolock whle closng and openng (for tme settng see F27 functon). Note: Myto, Frog.J, Stylo-RME and Amco gearmotors. = wth openng command (default settng); 1 = wth closng command; 2 = wth both commands. F F 7 2 F 18 (1-E Lght) : output on contact 1-E for lght wth followng functon: - movement flashng, flashes durng gate openng and closng. - outdoor lamp that can be freely postoned, for addtonal lghtng of the drveway s set up as a courtesy lght and stays on for an adjustable tme nterval (see functon F25 ) or as a cycle lght, whch stays on from the moment the gate leaf begns to open, untl t s fully closed (ncludng automatc closng tme). = Flashng lght (default settng); 1 = Cycle; 2 = Courtesy. F F 8 2 F 19 (Automatc Closng tme) : The automatc closng tmer actvates at each openng endpont. The predetermned tme may be adjusted, and s n any case dependent on any safety devces that may actvate; and t does not actvate after a total safety stop or durng a power outage. The watng tme can be deactvated or set to between 1 and 18. = Deactvated (default settng); 1 = 1 second; 2 = 2 seconds; = 18 seconds. F F 9 I 8

16 F2 (Automatc closng tme after partal or pedestran openng) : Automatc closng tme of the gate leaf after a partal openng or pedestran command. Once ths tme has elapsed, the gate automatcally closes and t s n any case condtoned by any safety devces that may be trggered, and s deactvated after a total safety stop or due to a power falure. The watng tme can be deactvated or set to between 1 and 18. Note: the automatc closng tme (see F 19) must not be deactvated. 1 = 1 second; 2 = 2 seconds;... 5 = 5 seconds (default settng); = 18 seconds. F F 2 2 I 8 F 21 (Pre-flashng tme) : after an openng or closng command, the flashng lght, connected to 1-E, starts flashng for a preset tme nterval before startng the gate run. The pre-flashng tme can be deactvated or set to between 1 and 1. = deactvated (default settng); 1 = 1 second; 2 = 2 seconds;... 1 = 1 seconds. F F F 2 F 22 (Workng tme) : workng tme of the motors when openng or closng. The workng tme may be set to between 5 and = 5 seconds; = 12 seconds; (default settng). I F I 2 F 23 (Openng slow-down tme) : after and openng command, the gate leaf of the M1 gearmotor delays openng compared to the M2 gearmotor for an adjustable tme nterval, The delay tme can be deactvated or set to between 1 and 1. = deactvated (default settng); 1 = 1 second; 2 = 2 seconds;... 1 = 1 seconds. F F 2 3 I F 24 (Closng slow-down tme) : after and closng command, the gate leaf of the M2 gearmotor delays openng compared to the M1 gearmotor for an adjustable tme nterval, The delay tme can be deactvated or set to between 1 and 25. = deactvated (default settng); 1 = 1 second; 2 = 2 seconds; = 25 seconds. F F P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

17 F 25 ( Courtesy lght tme) : supplementary lght connected on (1-E), stays on whle gate s openng and closng. The tme can be set to between 6 and = 6 seconds (default settng); 61 = 61 seconds...; 18 = 18 seconds. F F I 8 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F 26 (Ram head blow) : thrust tme of the gearmotor when n fnal closng and openng stage after each command. The tme may be set to between 1 and 2. Note: ths functon only appears for the Myto, Frog-J, Stylo-RME and Amco gearmotors. 1 = 1 second (default settng); 2 = 2 seconds. F F F 27 (lock tme) : acton tme for releasng the electrolock wth each openng or closng command (see F 17). The tme can be set to between 1 and 4. Note: ths functon only appears for the Myto, Frog-J, Stylo-RME and Amco gearmotors. 1 = 1 second (default settng);... 4 = 4 seconds. F F F 28 (M1 motor speed) : settng the speed of operaton of the M1 motor calculated as a percentage: 4 = 4% of the motor speed(mnmum);... 1 = 1% of the motor speed (maxmum and default settng). F F I F 29 (M2 motor speed) : settng the speed of operaton of the M2 motor calculated as a percentage: 4 = 4% of the motor speed(mnmum);... 1 = 1% of the motor speed (maxmum and default settng). F F I F 3 (Slow-down speed of M1 motor) : settng the speed of the M1 motor durng slow downs, calculated as a percentage. 2 = 2% motor slow-down speed (mnmum);... 5 = 5% motor slow-down speed (default settng);... 6 = 6% motor slow-down speed (maxmum). F F

18 F 31 (Slow-down speed of M2 motor) : settng the speed of the M2 motor durng slow downs, calculated as a percentage. 2 = 2% motor slow-down speed (mnmum);... 5 = 5% motor slow-down speed (default settng);... 6 = 6% motor slow-down speed (maxmum). F F F 32 (Addtonal slow-down when closng of M1 + M2) : Settng of an addtonal reducton n speed durng closng slow-downs for the straght-arm M1 and M2 motors; the reduced speed s calculated as a percentage. Note: ths functon only appears for the Myto, and Stylo straght-arm gearmotors. 1 = 1% motor slow-down speed (mnmum);... 5 = 5% motor slow-down speed (maxmum and default settng) F F 3 2 I I I 5 F 33 (calbraton speed) : settng the speed only for the gate calbraton phase, calculated as a percentage. 3 = 3% of the motor speed;... 5 = 5% of the motor speed (default settng);... 6 = 6% of the motor speed. F F F 34 (gate run senstvty) : adjusts the obstacle detecton senstvty durng the gate runs. 1 = maxmum senstvty;... 1 = mnmum senstvty (default senstvty). F F 3 4 I I I I F 35 (Slow-down senstvty) : adjusts the obstacle detecton senstvty durng slow-downs. 1 = maxmum senstvty;... 1 = mnmum senstvty (default senstvty). F F 3 5 I I I I F 36 (Adjustng Partal Openng) : adjusts the openng of the gate leaf of the M2 (second) motor as a percentage of the total gate run. 1 = 1% of the gate run (default settng);... 8 = 8% of the gate run. F F 3 6 I I I 8 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

19 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F 37 (Slow-down pont when openng the M1 motor) : adjusts the pont at whch the M1 motor begns to slow down when openng. The begnnng slow-down pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts) 1 = 1% of the gate run; = 25% of the gate run (default settng);... 6 = 6% of the gate run. F F 3 7 I I I 6 F 38 (Slow-down pont when closng the M1 motor) : adjusts the pont at whch the M1 motor begns to slow down when closng. The begnnng slow-down pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts) 1 = 1% of the gate run; = 25% of the gate run (default settng);... 6 = 6% of the gate run. F F 3 8 I I I 6 F 39 (Pont when M1 motor draws fully open) : adjusts the pont at whch the M1 motor begns drawng to the fully-open poston Ths pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts) 1 = 1% of the gate run;... 5 = 5% of the gate run (default settng);...1 = 1% of the gate run. F F I F 4 (Pont when M1 motor draws fully closed) : adjusts the pont at whch the M1 motor begns drawng to the fully-closed poston. Ths pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts at whch gate draws fully open or closed.) 1 = 1% of the gate run;... 5 = 5% of the gate run (default settng);... 1 = 1% of the gate run. F F 4 2 I F 41 (Pont when M2 motor s fully open) : adjusts the pont at whch the M2 motor begns to be fully-open. The begnnng slow-down pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts at whch gate draws fully open or closed) 1 = 1% of the gate run; = 25% of the gate run (default settng);... 6 = 6% of the gate run. F F 4 I I I 6... F 42 (Slow-down pont when closng the M2 motor) : adjusts the pont at whch the M2 motor begns to slow down when closng. The begnnng slow-down pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts at whch gate draws fully open or closed) 1 = 1% of the gate run; = 25% of the gate run (default settng);... 6 = 6% of the gate run. F F 4 2 I I I 6...

20 F 43 (Pont when M2 motor draws fully open) : adjusts the pont at whch the M2 motor begns drawng to the fully-open poston. Ths pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts at whch gate draws fully open or closed) 1 = 1% of the gate run;... 5 = 5% of the gate run (default settng);... 1 = 1% of the gate run. F F I F 44 (Pont when M2 motor draws fully closed) : adjusts the pont at whch the M2 motor begns drawng to the fully-closed poston. Ths pont s calculated as a percentage of the full gate run (see paragraph llustratng the slow-down areas and ponts) 1 = 1% of the gate run;... 5 = 5% of the gate run (default settng);... 1 = 1% of the gate run. F F I F45 (Addtonal closng slow-down pont) : adjusts the pont at whch there s an addtonal slow-down when closng, calculated as a percentage of the slow-down. Note: ths functon s vsble only for the straght-arm Myto and Stylo gearmotors. 1 = 1% of the slow-down run;... 5 = 5% of the slow-down run (default settng);... 1 = 1% of the slowdown run. F F 4 5 I I I I... F 46 (Number of Motors) : sets the number of motors connected to the control panel. = Engages both the M1 and M2 motors (default settng); 1 = Engages only one, the M2 motor. F F 4 6 F 5 (Save data) : saves all users and settngs n the memory roll. Note: ths functon appears only f the memory roll s nserted nto the mother board. = Deactvated; 1 = Actvated F F 5 F 51 (Data Read out) : loads the data from the memory roll nto the mother board. Note: ths functon appears only f the memory roll s nserted nto the mother board. = Deactvated; 1 = Actvated. F F 5 P. 2 - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

21 User Menu U 1 (add user wth assgned command) : add user (max. 25 users) assgned to a command va transmtter or other devce (see paragraph on addng users wth assgned command). 1 = step-by-step command (open-close); 2 = sequental command (open-stop-close-stop); 3 = open only command; 4 = pedestran / partal openng command (see functon F8 ; 5 = B1-B2 contact output. P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. F u 2 3 U 2 (Cancel user) : cancels sngle user (see paragraph on cancellng sngle users) F u U 3 (Cancel users) : cancels all memorzed users. Press to confrm. = Deactvated; 1 = Cancel all users. F u 3 F H I.... Info Menu H 1 (Verson) : dsplays software verson

22 CANCELLI AUTOMATICI CANCELLI AUTOMATICI CAME Decodng cards To nsert, change, remove users or to command the operator va rado command, nsert the AF43S card. If usng the transponder or card reader, nsert the R7 card or, alternatvely, the R8 card for the keyboard selector. Insert the memory roll to save and load all settngs ncludng users regstered by another card. R7 ACCESS CONTROL R7 Memory roll S7 R8 R8 Frequency/MHz Card Transmtter FM AF13 TFM FM 3.9 AF15 TFM AM AF26 TOP AM 3.9 AF3 TOP AM AF43S TAM / TOP ATOMO / TWIN AM AF43TW TWIN AM AF4 TOUCH AM AF868 TOP TSP AF TOP CAME LT1 ATOMO TAM TFM TWIN TOUCH P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

23 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. Addng users wth an assgned command N.B.: Before proceedng, remove the memory roll card. 1) Select U 1. Press to confrm. 2) select command (1=step-by-step, 2=sequental, 3=open, 4=pedestran / partal openng, 5= B1-B2 output contact) to assgn to user va the greater-than and lesser-than arrows on the keyboard... 3) an avalable number between 1 and 25 wll flash for a few seconds. Ths number wll be assgned to the user after sendng the code va transmtter or other command devce. Cancellng sngle users 1) Select U 2. Press to confrm. 2) Select the number of the user to cancel usng the greater-than/lesser-than arrow keys. Press to confrm 3) CLr wll be dsplayed to confrm the cancellaton. U I ESC < 2 ESC < ESC < U ESC < ESC < C L 8 ESC < Assgned Command user

24 Motor tests 1) Select A2. Press to confrm. a 2 ESC < 2) Select 1 to actvate test. Press to confrm... 3) --- wll be dsplayed, standng by for a command 4) Keep the key pressed down and check that the gate leaf of the second gearmotor (M2) opens fully. Note: f the gate leaf closes nstead of openng, nvert the motor phases (M2 wth N2). 5) Carry out the same procedure wth the < key to check the gate leaf of gearmotor (M1). Note: f the gate leaf closes fully, nvert the motor phases (M1 wth N1). I ESC < ESC < op2 ESC < op I ESC < M1 M1 M2 M2 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

25 Gate run calbraton N.B: before proceedng wth the calbraton of the gate run, check that the area of movement s free of any obstacles and check that there s a mechancal stop or both openng and closng. Important! Whle calbratng, all safety devces wll be dsabled untl the end of the calbraton excludng the total stop 1) Select A3. Press to confrm. a 3 P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. 2) Select 1 and press to confrm, the automatc gate run calbraton procedure... 3) the gate leaf of the frst motor wll close fully untl the mechancal stop 4) then, the gate leaf of the second motor wll do the same 5) then, the gate leaf of the second motor, shall fully open untl the mechancal stop 6) then, the gate leaf of the frst motor wll do the same. ESC < ESC < cl ESC < cl2 ESC < op2 ESC < op I ESC <

26 Illustraton of the slow-down areas and ponts at whch gate draws to the fully open or closed poston Note: the slow-down areas and ponts at whch the gate draws to the fully open or closed poston are tested accordng to the parameters set forth by Techncal Norms EN12445 and EN12453 regardng compatblty of mpact forces generated by movng gate leaves. M1 B D P I O L P D B M2 O D M B A E C A = Area of movement at normal speed B* = Run zone at slow-down speed C = Encoder nterventon zone wth movement nverson D= Encoder nterventon zone wth movement stop E = Openng slow-down begnnng pont (M1 Open Slow- %) F = Closng slow-down begnnng pont (M1 Close Slow- %) G = Openng slow-down begnnng pont (M2 Open Slow- %) H = Closng slow-down begnnng pont (M2 Close Slow- %) I** = Pont at whch gate begns drawng to fully-closed poston (M1 Close appr. %) L** = Pont at whch gate begns drawng to fully-closed poston (M2 Close appr. %) M**= Pont at whch gate begns drawng to fully-open poston (M1 Acc. AP%) N**= Pont at whch gate begns drawng to fully-open poston (M2Acc. AP%) O = Mechancal Stops P = Area n whch addtonal slow- down speed takes place when closng, only for the straght-arm Stylo and Myto motors) Q = Pont at whch addtonal slow-down when closng begns, only for the straght-arm Stylo and Myto motors) F * Mnmum 6 mm from the Fnal full stop. ** Set the functon s approach % M1 Close appr. for the f rst (M1) motor and M2 Close appr. for the second (M2) motor from the ENCODER menu so as to obtan a dstance of between 1 and 5 mm max. from the f nal full stop. Q H C G A B N D O P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A.

27 Error messages and warnngs P Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. - The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. Er1 : M1 motor calbraton nterrupted; check proper connecton and workng state of M1 motor. Er2 : motor calbraton nterrupted; check proper connecton and workng state of M1 motor. Er3 : broken encoder; call for assstance. Er4 : servces test error; check proper connecton and workng status of the safety devces. Er5 : nsuffcent workng tme; Check tme settng, t could be nsuffcent to complete the workng cycle. Er6 : maxmum number of detected obstacles. Er7 : transformer overheated, at frst openng command, gate leaves stay open. C : contact 1-2 (stop) unused and not deactvated. C1/2/3/4/7/8 : contacts CX and/or CY are unused and not deactvated. Red LED ndcator lght flashes: command card stll not calbrated to the gate run. Phasng out and dsposal In ts premses, CAME cancell automatc S.p.A. mplements an Envronmental Management System certfed n complance wth the UNI EN ISO 141 standard to ensure envronmental protecton. Please contnue our efforts to protect the envronment - whch CAME consders one of the cardnal elements n the development of ts operatonal and market strateges - smply by observng bref recommendatons as regards dsposal: DISPOSAL OF PACKAGING The packagng components (cardboard, plastc, etc.) are all classfable as sold urban waste products and may be dsposed of easly, keepng n mnd recyclng possbltes. Pror to dsposal, t s always advsable to check specfc regulatons n force n the place of nstallaton. PLEASE DISPOSE OF PROPERLY! PRODUCT DISPOSAL Our products are made up of varous types of materals. Most of them (alumnum, plastcs, ron, electrcal wres, etc.) may be dsposed of n normal garbage collecton bns and can be recycled by dsposng of n specfc recyclable materal collecton bns and dsposal n authorzed centres. Other components (electrcal boards, remote control batteres, etc.), however, may contan pollutng substances. They should therefore be removed and gven to qualfed servce companes for proper dsposal. Pror to dsposal, t s always advsable to check specfc regulatons n force n the place of dsposal. PLEASE DISPOSE OF PROPERLY! CE complance certfcaton Declaraton - Came Cancell Automatc S.p.A. declares that ths product conforms to the essental, pertnent requrements provded by drectves 26/95/CE and 24/18/CE. An orgnal copy of the declaraton of conformty s avalable on request.

28 Englsh - Manual code: 319V21EN Vers. 3 9/214 CAME cancell automatc S.p.A. The data and nformaton n ths manual are subject to change at any tme wthout pror notce requred by Came Cancell Automatc S.p.A. IT Per ogn ulterore nformazone su azenda, prodott e assstenza nella vostra lngua: EN For any further nformaton on company, products and assstance n your language: FR Pour toute autre nformaton sur la socété, les produts et l assstance dans votre langue : DE Wetere Infos über Unternehmen, Produkte und Kundendenst be: ES Por cualquer nformacón sobre la empresa, los productos y asstenca en su doma: NL Voor meer nformate over het bedrjf, de producten en hulp n uw egen taal: PT Para toda e qualquer nformação acerca da empresa, de produtos e assstênca técnca, em sua língua: PL Wszystke nne nformacje dotyczące f rmy, produktów oraz usług pomocy techncznej w Waszym języku znajdują sę na strone: RU Для получения дополнительной информации о компании, продукции и сервисной поддержке на вашем языке: HU A vállalatra, termékere és a műszak szervzre vonatkozó mnden tovább nformácóért az Ön nyelvén: HR Za sve dodatne nformacje o poduzeću, prozvodma tehnčkoj podršc: UK Для отримання будь-якої іншої інформації про компанію, продукцію та технічну підтримку: www. came.com CAME Cancell Automatc S.p.A. Va Martr Della Lbertà, Dosson D Caser (Tv) (+39) (+39) Assstenza Tecnca/Numero Verde

Strain Gauge Measuring Amplifier BA 660

Strain Gauge Measuring Amplifier BA 660 Stran Gauge Measurng Amplfer BA 660 Orgnal of the Manual BA660 / IP20 BA660 / IP66 Table of Contents 1. Safety precautons...2 1.1. Feld of applcaton...2 1.2. Installaton...2 1.3. Mantenance...2 2. Functon...2

More information

1. REVIEW 2. DELIVERY SET

1. REVIEW 2. DELIVERY SET power status ON steps DIP test reset ON DIP off modes lght sensor / led sensor speed on sensor 2 speed off on/off delay pause to off REVIEW LED lghtng devce s desgned for automatc lghtng of starway steps

More information

VRT014 User s guide V0.8. Address: Saltoniškių g. 10c, Vilnius LT-08105, Phone: (370-5) , Fax: (370-5) ,

VRT014 User s guide V0.8. Address: Saltoniškių g. 10c, Vilnius LT-08105, Phone: (370-5) , Fax: (370-5) , VRT014 User s gude V0.8 Thank you for purchasng our product. We hope ths user-frendly devce wll be helpful n realsng your deas and brngng comfort to your lfe. Please take few mnutes to read ths manual

More information

Parking barrier Parc 200 / Parc 200 speed

Parking barrier Parc 200 / Parc 200 speed GB Operatng nstructons Last updated: 01.2014 Parkng barrer Parc 200 / Parc 200 speed 1. Meanng of symbols 2. Table of contents Advce Cauton! Danger of personal njury! The followng safety advce must be

More information

Locator Pin Indexing Pin. Wire Size Marking CAUTION NOTE TOOLING ASSISTANCE CENTER PRODUCT INFORMATION

Locator Pin Indexing Pin. Wire Size Marking CAUTION NOTE TOOLING ASSISTANCE CENTER PRODUCT INFORMATION ROTA-CRIMP* Crmpng Tool Instructon Sheet 408-2681 68321-1 13 APR 12 Statonary De (Nest) Anvl De Hold-Down Devce and Contact Locator Front of Tool Locator Pn Indexng Pn Wre Sze Markng The hold-down devce

More information

PRO- CRIMPER III Hand Crimping Tool Assembly DESCRIPTION (Figures 1 and 2)

PRO- CRIMPER III Hand Crimping Tool Assembly DESCRIPTION (Figures 1 and 2) PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58495-1 408-9819 Wth De Assembly 58495-2 22 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

onlinecomponents.com

onlinecomponents.com PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58535-1 wth 408-4021 De Assembly 58535-2 29 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

Pneumatic Power Bench Assembly

Pneumatic Power Bench Assembly Pneumatc Power Bench Assembly 58338-1 Instructon Sheet 408-9393 09 AUG 11 Fgure 1 1. INTRODUCTION Pneumatc Power Bench Assembly 58338-1 s a pneumatc power unt desgned to accept a varety of nterchangeable

More information

PRO- CRIMPER* III Hand Crimping

PRO- CRIMPER* III Hand Crimping PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58641-1 wth 408-4379 De Assembly 58641-2 18 JUN 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

PRO- CRIMPER* III Hand

PRO- CRIMPER* III Hand PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 58529-1 408-9999 wth De Assembly 58529-2 11 AUG 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

SDE PEW- 12 Hand Tool

SDE PEW- 12 Hand Tool SDE PEW- 12 Hand Tool Instructon Sheet Assembly 2063956-1 wth 408-10370 De Assembly 2063956-2 07 OCT 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered

More information

PRO- CRIMPER* III Hand Crimping

PRO- CRIMPER* III Hand Crimping PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 91338-1 408-8377 wth De Assembly 91338-2 22 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

PRO- CRIMPER* III Hand

PRO- CRIMPER* III Hand PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 90759-1 408-9962 wth De Assembly 90759-2 03 MAY 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

Instruction Sheet SDE- SA Hand Tool Assembly with Die Assembly

Instruction Sheet SDE- SA Hand Tool Assembly with Die Assembly Instructon Sheet 408-10002 wth De Assembly 1752938-2 06 APR 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are ntended for

More information

PRO- CRIMPER III Hand Crimping Tool Assembly INSTALLATION AND REMOVAL OF DIE SET AND LOCATOR ASSEMBLY (Figure 2)

PRO- CRIMPER III Hand Crimping Tool Assembly INSTALLATION AND REMOVAL OF DIE SET AND LOCATOR ASSEMBLY (Figure 2) PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 90547-1 wth 408-9884 De Assembly 90547-2 02 NOV 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

PRO-CRIMPER* III Hand Crimping Tool Assembly with Die AssemblY

PRO-CRIMPER* III Hand Crimping Tool Assembly with Die AssemblY PRO-CRIMPER* III Hand Crmpng Tool Assembly 90758-1 wth De AssemblY 90758-2 Instructon Sheet 408-9938 01 NOV 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

SPeCtra X-XL. Section 4 Troubleshooting. read the safety information chapter before working on the machines.

SPeCtra X-XL. Section 4 Troubleshooting. read the safety information chapter before working on the machines. 4 SPeCtra X-XL en Secton 4 Troubleshootng Document Number: TD 103 421/A Order Number: 1H 328 259 read the safety nformaton chapter before workng on the machnes. Change log Date Changes Author No. ID 2011-10-19

More information

INSTRUCTION MANUAL BENCH LATHE

INSTRUCTION MANUAL BENCH LATHE WLLOUGHBY COMMUNTY MEN'S SHED mens 296C Salors Bay Road, l _ L^ NORTHBRDGE N.S.W 2063 The Wlkmghby Communty" NSTRUCTON MANUAL BENCH LATHE Before usng be sure to read ths manual carefully -C6- Safety nstructons

More information

PRO-CRIMPER* III Hand. with Die Assembly OCT 11 Rev C. Pivot Pin. Die Assembly Moving Jaw CONTACT FAMILY SIZE (AWG)

PRO-CRIMPER* III Hand. with Die Assembly OCT 11 Rev C. Pivot Pin. Die Assembly Moving Jaw CONTACT FAMILY SIZE (AWG) PRO-CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 58514-1 408-9973 wth De Assembly 58514-2 12 OCT 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

Hand Crimping Tool (For Insulated Heat Shrink Splices)

Hand Crimping Tool (For Insulated Heat Shrink Splices) Hand Crmpng Tool 607949-1 (For Insulated Heat Shrnk Splces) Instructon Sheet 408-4087 23 JAN 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand

More information

Product Information. Jaw quick-change system BSWS-PGZN-plus

Product Information. Jaw quick-change system BSWS-PGZN-plus Product Informaton BSWS-PGZN-plus BSWS-PGZN-plus Productve. Flexble. Cost-effectve. BSWS jaw quck-change system The BSWS jaw quck-change system allows top jaws to be changed on the grpper manually and

More information

PRO-CRIMPER* III Hand Crimping Tool Assembly with Die Assembly

PRO-CRIMPER* III Hand Crimping Tool Assembly with Die Assembly PRO-CRIMPER* III Hand Crmpng Tool Assembly 90548-1 wth De Assembly 90548-2 Instructon Sheet 408-9885 02 NOV 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

PRO- CRIMPER* III Hand Crimping

PRO- CRIMPER* III Hand Crimping PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool 58448-2 408-9357 Wth De 58448-3 10 Mar 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand

More information

PRO- CRIMPER* III Hand

PRO- CRIMPER* III Hand PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 90684-1 408-9934 wth De Assembly 90684-2 09 OCT 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

PRO-CRIMPER* III Hand Tool Assembly with Die Assembly

PRO-CRIMPER* III Hand Tool Assembly with Die Assembly PRO-CRIMPER* III Hand Tool Assembly 2063778-1 wth De Assembly 2063778-2 Instructon Sheet 408-10290 02 FEB 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

Instructions for Use. PetChatz.com. PetChatz.com

Instructions for Use. PetChatz.com. PetChatz.com Instructons for Use PetChatz.com PetChatz.com POWER ON/OFF LED PET-SAFE MICROPHONE SOUND DETECTOR MANUAL TREAT RELEASE LOW TREAT LED LOW-LIGHT HD CAMERA for hgh-qualty vdeo MOTION DETECTION FULL-COLOR

More information

Customer witness testing guide

Customer witness testing guide Customer wtness testng gude Ths gude s amed at explanng why we need to wtness test equpment whch s beng connected to our network, what we actually do when we complete ths testng, and what you can do to

More information

Shur-Plug*.156 Diameter Terminals and Receptacle Contacts

Shur-Plug*.156 Diameter Terminals and Receptacle Contacts Shur-Plug*.156 Dameter Termnals and Receptacle Contacts Applcaton Specfcaton 114-2042 07 NOV 12 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and

More information

Figure 1. DC-DC Boost Converter

Figure 1. DC-DC Boost Converter EE46, Power Electroncs, DC-DC Boost Converter Verson Oct. 3, 11 Overvew Boost converters make t possble to effcently convert a DC voltage from a lower level to a hgher level. Theory of Operaton Relaton

More information

DALI gateway Tunable White Plus Order No

DALI gateway Tunable White Plus Order No Product documentaton Issue: 20.07.2017 21083100 DALI gateway Tunable Whte Plus Table of Contents Product documentaton 1 Product defnton... 4 1.1 Product catalogue... 4 1.2 Functon... 4 2 Mountng, electrcal

More information

Instruction Sheet ROTA- CRIMP* Hand Crimping Tools and

Instruction Sheet ROTA- CRIMP* Hand Crimping Tools and Instructon Sheet ROTA- CRIMP* Hand Crmpng Tools 08-09 6007 and 6007- APR PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are

More information

PRO-CRIMPER* III Hand Crimping Tool Assembly and Die Assemblies [ ]

PRO-CRIMPER* III Hand Crimping Tool Assembly and Die Assemblies [ ] PRO-CRIMPER* III Hand Crmpng Tool Assembly 58546-1 and De Assembles 58545-[ ] Instructon Sheet 408-8678 13 MAR 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

DALI gateway Plus Order No

DALI gateway Plus Order No KNX Product documentaton Issue: 18.09.2015 21803200 DALI gateway Plus Table of Contents KNX Product documentaton 1 Product defnton... 4 1.1 Product catalogue... 4 1.2 Functon... 4 2 Installaton, electrcal

More information

C O N C E A L E D F I X I N G. PH:

C O N C E A L E D F I X I N G.   PH: C O N C E A L E D I X I N G D I Y S l a t Systems PH: 1300 336 237 Alumnum Concealed xng Slat Systems Our Concealed xng Alumnum Slat range offers the latest n archtectural style combned wth a unque nstall

More information

Figure 1. DC-DC Boost Converter

Figure 1. DC-DC Boost Converter EE36L, Power Electroncs, DC-DC Boost Converter Verson Feb. 8, 9 Overvew Boost converters make t possble to effcently convert a DC voltage from a lower level to a hgher level. Theory of Operaton Relaton

More information

MCP 2.8 mm Contact System and Wire Seal for 1P Starter Motor Connectors

MCP 2.8 mm Contact System and Wire Seal for 1P Starter Motor Connectors MCP 2.8 mm Contact System and Wre Seal for 1P Starter Motor Connectors Applcaton Specfcaton 114-13295 05 MAY 11 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n

More information

HR Brief description. 1. Scope of delivery

HR Brief description. 1. Scope of delivery 2. Bref descrpton. Scope of delvery HR92 Wreless Radator Controller The radator controller packagng contans: 2 HR92 s an electronc radator controller wth a modern desgn. Because of the wreless communcaton

More information

HR Brief description. 1. Scope of delivery

HR Brief description. 1. Scope of delivery 2. Bref descrpton 2443 The HR92 radator controller s certfed by eu.bac.. Scope of delvery HR92 Wreless Radator Controller The radator controller packagng contans: 2 HR92 s an electronc radator controller

More information

Table of Contents. Stabila LD420 1

Table of Contents. Stabila LD420 1 Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - Introducton- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Overvew - - - - - - - - - - - - - - - - - - -

More information

Unit 1. Current and Voltage U 1 VOLTAGE AND CURRENT. Circuit Basics KVL, KCL, Ohm's Law LED Outputs Buttons/Switch Inputs. Current / Voltage Analogy

Unit 1. Current and Voltage U 1 VOLTAGE AND CURRENT. Circuit Basics KVL, KCL, Ohm's Law LED Outputs Buttons/Switch Inputs. Current / Voltage Analogy ..2 nt Crcut Bascs KVL, KCL, Ohm's Law LED Outputs Buttons/Swtch Inputs VOLTAGE AND CRRENT..4 Current and Voltage Current / Voltage Analogy Charge s measured n unts of Coulombs Current Amount of charge

More information

100 mm. 200 mm. 300 mm. 500 mm. Wood (rough) Cardboard Black DBT DBT DBT DBT DBT - 1 K DBT K CONNECTION DIAGRAMS.

100 mm. 200 mm. 300 mm. 500 mm. Wood (rough) Cardboard Black DBT DBT DBT DBT DBT - 1 K DBT K CONNECTION DIAGRAMS. DIFFUSED BEAM SENSOR Ths devce consst of a transmtter and a recever together. Ths look alke Inductve Proxmty Sensor and hence also known as IR Proxmty Sensor. The emtter emts Infra red rays whch are reflected

More information

STRATO-THERM* Terminal and Splice Hand Crimping Tools and 59461

STRATO-THERM* Terminal and Splice Hand Crimping Tools and 59461 STRATO-THERM* Termnal and Splce Hand Crmpng Tools 59294 and 59461 Instructon Sheet 408-1259 17 AUG 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered

More information

AFV-P 2U/4U. AC + DC Power Solutions. series. Transient Generation for Disturbance Tests. only. High Performance Programmable AC Power Source

AFV-P 2U/4U. AC + DC Power Solutions. series. Transient Generation for Disturbance Tests. only. High Performance Programmable AC Power Source AFV-P seres Hgh Performance Programmable AC Power Source only 2U/4U Intutve Touch Screen HMI Output Frequency up to 15-1000Hz Power Lne Smulatons: Step & Ramp Features Fast Response Tme: 300μs AC Source

More information

1 Signs and symbols. 4 Installation 5 Active window 6 Commissioning Filter settings edali addressing. 6.4 Addressing. 7 General functions

1 Signs and symbols. 4 Installation 5 Active window 6 Commissioning Filter settings edali addressing. 6.4 Addressing. 7 General functions Table of contents 1 Sgns and symbols... 5 2 Changes ntroduced... wth masterconfigurator 2.10 6 3 Introducton... 7 4 Installaton... 8 5 Actve wndow... 10 6 Commssonng... 12 6.1 Selectng... an nterface 12

More information

Instruction Sheet AMPMODU* MTE CONNECTORS Mar 11 Rev A

Instruction Sheet AMPMODU* MTE CONNECTORS Mar 11 Rev A Instructon Sheet AMPMODU* MTE CONNECTORS 408-6919 10 Mar 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are ntended for

More information

User manual FLOW METER SPP-N118

User manual FLOW METER SPP-N118 Assstng the automaton ndustry snce 1986 User manual FLOW METER SPP-N118 Frmware: v.6.00 or hgher Input type: 0/4-20 ma Batchng and totalzer functon Read the user's manual carefully before startng to use

More information

LITECOM. Self-contained emergency luminaires

LITECOM. Self-contained emergency luminaires LITECOM Self-contaned emergency lumnares Legal nformaton Copyrght Copyrght Zumtobel Lghtng GmbH All rghts reserved. Manufacturer Zumtobel Lghtng GmbH Schwezerstrasse 30 6850 Dornbrn AUSTRIA Tel. +43-(0)5572-390-0

More information

2E - 3E High Wind Kit Manual

2E - 3E High Wind Kit Manual Yag Dpole Vertcal (Patent# 6,677,914 E - 3E Hgh Wnd Kt Manual Antarctca at 7 mph SteppIR Antennas 11-116th Ave NE, Sute -, Bellevue, WA 984 Tel: 4-43-191 Fax: 4-46-441 Tech Support: 4-891-6134 www.steppr.com

More information

MULTIPOLE CONNECTORS SQUICH CN NEW SQUICH. Connections without tools reduced space SQUICH A TIMESAVER

MULTIPOLE CONNECTORS SQUICH CN NEW SQUICH. Connections without tools reduced space SQUICH A TIMESAVER SCREW CONNECTION ULTIPOLE CONNECTORS SQUICH CN SQUICH SQUICH Connectons wthout tools reduced space A TIESAVER SQUICH ULTIPOLE CONNECTORS SQUICH CN SQUICH seres Connectons wthout tools To mprove hgh performance

More information

Operating Instructions. MarSurf M RD 18

Operating Instructions. MarSurf M RD 18 Operatng Instructons MarSurf M 300 + RD 18 DE Deutsch EN Englsh FR Franças IT Italano ES Español PT Português Mahr GmbH, MarSurf M 300 + RD 18 Mahr GmbH, MarSurf M 300 + RD 18 Dear valued customer, Congratulatons

More information

RC Filters TEP Related Topics Principle Equipment

RC Filters TEP Related Topics Principle Equipment RC Flters TEP Related Topcs Hgh-pass, low-pass, Wen-Robnson brdge, parallel-t flters, dfferentatng network, ntegratng network, step response, square wave, transfer functon. Prncple Resstor-Capactor (RC)

More information

Microlectra bv. User manual FLOW METER SPP-N118

Microlectra bv. User manual FLOW METER SPP-N118 Mcrolectra bv. Assstng the automaton ndustry snce 1986 User manual FLOW METER SPP-N118 Frmware: up to v. 5. 11 Input type: 0/4-20 ma Batchng and totalzer functon Read the user's manual carefully before

More information

Grafik auf der Vorgabeseite in den Grafikrahmen importieren!

Grafik auf der Vorgabeseite in den Grafikrahmen importieren! Grafk auf der Vorgabesete n den Grafkrahmen mporteren! COMAND Operator s Manual Mercedes-Benz Order-No. DamlerChrysler 6515 6668 13 Blaupunkt 8 622 403 703 Index E Parts-No. 230 584 38 82 US Edton E 07/03

More information

Insertion/Extraction Tool and Replacement Tip Kits [ ]

Insertion/Extraction Tool and Replacement Tip Kits [ ] Inserton/Extracton Tool 91285-1 and Replacement Tp Kts 543382-[ ] Instructon Sheet 408-9404 19 JUN 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered

More information

Gripping force, O.D. gripping. Gripping force, I.D. gripping

Gripping force, O.D. gripping. Gripping force, I.D. gripping Grppng force, O.D. grppng Fnger load Grppng force Grppng force, I.D. grppng Grppng force Fnger length M x max. 80 Nm M y max. 115 Nm M z max. 70 Nm F z max. 2000 N Fnger length The ndcated moments and

More information

User manual COUNTER SLIK-N118

User manual COUNTER SLIK-N118 Assstng the automaton ndustry snce 1986 User manual COUNTER SLIK-N118 Frmware: v.8.10 or hgher Input type: pulse, quadrature Batchng functon, wall mountng case IP 67 Read the user's manual carefully before

More information

SDE Electric Bench Terminator READ THIS FIRST! customer manual TOOLING ASSISTANCE CENTER

SDE Electric Bench Terminator READ THIS FIRST! customer manual TOOLING ASSISTANCE CENTER SDE Electrc Bench Termnator 1490076-2 Customer Manual 409-10052 31 JAN 12 customer manual SAFETY A. PRECAUTIONS READ THIS FIRST!............................ 2 1. INTRODUCTION........................................................

More information

Table of contents Document code: DPD00288B2 Edited:

Table of contents Document code: DPD00288B2 Edited: Table of contents Document code: DPD00288B2 Edted: 18.06.2010 1. Safety 3 1.1 Warnngs 3 1.2 Safety nstructons 5 1.3 Earthng and earth fault protecton 5 1.4 Before runnng the motor 6 2. Recept of delvery

More information

Grafik auf der Vorgabeseite in den Grafikrahmen importieren!

Grafik auf der Vorgabeseite in den Grafikrahmen importieren! Grafk auf der Vorgabesete n den Grafkrahmen mporteren! COMAND Operator s Manual Mercedes-Benz Order-No. DamlerChrysler 6515 6665 13 Blaupunkt 8 622 403 493 Index D Parts-No. 230 584 36 82 US Edton B 10/02

More information

Operator's Manual A1000. Applicator. Made in Germany

Operator's Manual A1000. Applicator. Made in Germany Operator's Manual Applcator A1000 Made n Germany 2 Operator's Manual - Translaton of the Orgnal Verson 2 for the followng products Famly A1000 Edton: 03/2016 - Part No. 9009599 Copyrght Ths documentaton

More information

Product Information. Universal gripper JGZ

Product Information. Universal gripper JGZ Product Informaton Unversal grpper JGZ JGZ Unversal grpper Loadable. Relable. Compact. JGZ unversal grpper Unversal 3-fnger centrc grpper of the compact class wth T-slot gudance and best cost-performance

More information

USER MANUAL for flow meter with current input SPP-94. firmware version: 1.04 or higher

USER MANUAL for flow meter with current input SPP-94. firmware version: 1.04 or higher SIMEX USER MANUAL for flow meter wth current nput famly: type: SPP-94 frmware verson: 1.04 or hgher Read the user's manual carefully before startng to use the unt. Producer reserves the rght to mplement

More information

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 1 Laboratory Energy Sources

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 1 Laboratory Energy Sources POLYTECHNIC UNIERSITY Electrcal Engneerng Department EE SOPHOMORE LABORATORY Experment 1 Laboratory Energy Sources Modfed for Physcs 18, Brooklyn College I. Oerew of the Experment Ths experment has three

More information

Dynamic Optimization. Assignment 1. Sasanka Nagavalli January 29, 2013 Robotics Institute Carnegie Mellon University

Dynamic Optimization. Assignment 1. Sasanka Nagavalli January 29, 2013 Robotics Institute Carnegie Mellon University Dynamc Optmzaton Assgnment 1 Sasanka Nagavall snagaval@andrew.cmu.edu 16-745 January 29, 213 Robotcs Insttute Carnege Mellon Unversty Table of Contents 1. Problem and Approach... 1 2. Optmzaton wthout

More information

Microlectra bv. User manual FLOW METER SPP-94

Microlectra bv. User manual FLOW METER SPP-94 Mcrolectra bv. Assstng the automaton ndustry snce 1986 User manual FLOW METER SPP-94 Input type: 0/4-20 ma Batchng and totalzer functon Read the user's manual carefully before startng to use the unt or

More information

Nordic - 2 Door Wardrobe

Nordic - 2 Door Wardrobe Nordc - 2 oor Wardrobe ssembly Instructons - lease keep for future reference 62967 mensons Wdth : 8. cm epth : 49,0 cm Heght : 9, cm Important - lease read these nstructons fully before startng assembly

More information

LED Fixture Controller ELED1 Programming Guide

LED Fixture Controller ELED1 Programming Guide LED Fxture Controller ELED1 Programmng Gude ELED1-AUN ELED1-AUS Copyrght 2018 Echoflex Solutons, Inc. All rghts reserved. Product nformaton and specfcaton detals subject to change Echoflex Solutons 38924

More information

AMPINNERGY* Modular Wiring System 25 JUL 11 Rev G

AMPINNERGY* Modular Wiring System 25 JUL 11 Rev G Applcaton Specfcaton 114-6039 AMPINNERGY* Modular Wrng System 25 JUL 11 Rev G All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and nches]. Unless otherwse

More information

Product Information. Universal gripper PGN-plus

Product Information. Universal gripper PGN-plus Product Informaton Unversal grpper PGN-plus PGN-plus Unversal grpper Relable. Robust. Flexble. PGN-plus unversal grpper Unversal 2-Fnger Parallel Grpper wth large grppng force and hgh maxmum moments due

More information

How to Get Started with Virtual Goalie

How to Get Started with Virtual Goalie How to Get Started wth Vrtual Goale HTC VIVE Set up your computer and moble devce Acqure a vrtual realty-enabled computer and the HTC Vve. For hardware specs, to test your computer, or to order from Amazon,

More information

IO.ZS-30.31Ex.02(ENG) APLISENS MANUFACTURE OF PRESSURE TRANSMITTERS AND CONTROL INSTRUMENTS USER S MANUAL

IO.ZS-30.31Ex.02(ENG) APLISENS MANUFACTURE OF PRESSURE TRANSMITTERS AND CONTROL INSTRUMENTS USER S MANUAL IO.ZS-30.31Ex.02(ENG) APLISENS MANUFACTURE OF PRESSURE TRANSMITTERS AND CONTROL INSTRUMENTS USER S MANUAL REPEATER POWER SUPPLY (POWER SUPPLY ISOLATOR) ZS 30Ex1 wth 24V DC supply ZS 31Ex1 wth 230V AC supply

More information

TheraPro HR Brief description. 1. Scope of delivery

TheraPro HR Brief description. 1. Scope of delivery . Bref descrpton 44 The HR9 radator controller s certfed by eu.bac.. Scope of delvery The radator controller packagng contans: Radator controller wth valve baseplate M x.5; batteres ncluded Dsplay support

More information

Nordic - 2 Door Wardrobe

Nordic - 2 Door Wardrobe Nordc - oor Wardrobe ssembly Instructons - lease keep for future reference 4457 mensons Wdth :. cm epth : 49,0 cm Heght : 9, cm Important - lease read these nstructons fully before startng assembly If

More information

Table of contents Doc: DPD00716A1, Date:

Table of contents Doc: DPD00716A1, Date: VACON 20 Table of contents Doc: DPD00716A1, Date: 22.11.11 1.Safety 1 1.1.Warnngs 1 1.2.Safety nstructons 3 1.3.Earthng and earth fault protecton 3 1.4.Before runnng the motor 5 2.Recept of delvery 6 2.1.Type

More information

User manual METER. TVU Series

User manual METER. TVU Series Assstng the automaton ndustry snce 1986 User manual METER TVU Seres Frmware: v.1.00 or hgher Input type: unversal Wall mountng case IP 67 Read the user's manual carefully before startng to use the unt

More information

User s manual. Digital control relay SVO/SVP

User s manual. Digital control relay SVO/SVP User s manual Dgtal control relay SVO/SVP DISIBEINT ELECTRONIC S.L, has been present n the feld of the manufacture of components for the ndustral automaton for more than 35 years, and mantans n constant

More information

EMA. Education Maintenance Allowance (EMA) Financial Details Form 2017/18. student finance wales cyllid myfyrwyr cymru.

EMA. Education Maintenance Allowance (EMA) Financial Details Form 2017/18. student finance wales cyllid myfyrwyr cymru. student fnance wales cylld myfyrwyr cymru Educaton Mantenance Allowance (EMA) Fnancal Detals Form 2017/18 sound advce on STUDENT FINANCE EMA Educaton Mantenance Allowance (EMA) 2017/18 /A How to complete

More information

User manual METER SRL-49

User manual METER SRL-49 Assstng the automaton ndustry snce 1986 User manual METER SRL-49 Frmware: v.5.21 or hgher Input type: 0/4-20 ma, 0/1-5V, 0/2-10V Multcolour bargraph Read the user's manual carefully before startng to use

More information

vacon 20 ac drives complete user manual

vacon 20 ac drives complete user manual vacon 20 ac drves complete user manual Document: DPD00716H1 Release date: July, 2016 Software package: FW0107V012.vcx 1.Safety 1 1.1Warnngs 1 1.2Safety nstructons 3 1.3Earthng and earth fault protecton

More information

User s manual. Digital Control Relay SAA SAB SAC SAD SAJ

User s manual. Digital Control Relay SAA SAB SAC SAD SAJ User s manual Dgtal Control Relay SAA SAB SAC SAD SAJ DISIBEINT ELECTRONIC S.L, has been present n the feld of the manufacture of components for the ndustral automaton for more than 35 years, and mantans

More information

100 Watt DC-DC Converters Q Series

100 Watt DC-DC Converters Q Series Bengn Envronment DC-DC Converters 100 Watt Q Seres 100 Watt DC-DC Converters Q Seres Input to output solaton Sngle output: Seres 24Q...48Q1000 Double output: Seres 24Q...48Q2000 Very hgh effcency of up

More information

Nordic - 2 Door 2 Drawer Tallboy

Nordic - 2 Door 2 Drawer Tallboy Nordc - oor rawer allboy ssembly Instructons - lease keep for future reference 66390 mensons Wdth : 8. cm epth : 49,0 cm Heght : 5,9 cm Important - lease read these nstructons fully before startng assembly

More information

MTBF PREDICTION REPORT

MTBF PREDICTION REPORT MTBF PREDICTION REPORT PRODUCT NAME: BLE112-A-V2 Issued date: 01-23-2015 Rev:1.0 Copyrght@2015 Bluegga Technologes. All rghts reserved. 1 MTBF PREDICTION REPORT... 1 PRODUCT NAME: BLE112-A-V2... 1 1.0

More information

Sensors for Motion and Position Measurement

Sensors for Motion and Position Measurement Sensors for Moton and Poston Measurement Introducton An ntegrated manufacturng envronment conssts of 5 elements:- - Machne tools - Inspecton devces - Materal handlng devces - Packagng machnes - Area where

More information

Service Manual 5414/5416. Vacuum-Belt Applicator. Made in Germany

Service Manual 5414/5416. Vacuum-Belt Applicator. Made in Germany Servce Manual Vacuum-Belt Applcator 5414/5416 Made n Germany 2 Servce Manual 2 for the followng products Famly Vacuum-Belt Applcator Type 5414L 5414R 5416L 5416R Edton: 04/2018 - Part No. 9003095 Copyrght

More information

Test 2. ECON3161, Game Theory. Tuesday, November 6 th

Test 2. ECON3161, Game Theory. Tuesday, November 6 th Test 2 ECON36, Game Theory Tuesday, November 6 th Drectons: Answer each queston completely. If you cannot determne the answer, explanng how you would arrve at the answer may earn you some ponts.. (20 ponts)

More information

Absco Space Saver Shed Assembly Instructions Model: J30082S

Absco Space Saver Shed Assembly Instructions Model: J30082S Assembly Instructons FRONT BASE LENGTH: 9ft-0-7 64n SIDE BASE LENGTH: ft-6-45 64n FRONT WALL HEIGHT: 5ft-0-55 64n REAR WALL HEIGHT: 6ft-4-49 64n ft-0-4 64n CONCRETE SLAB 0ft--3 64n CONCRETE SLAB WHEN LAYING

More information

User s manual. Digital control relay SNI

User s manual. Digital control relay SNI User s manual Dgtal control relay SNI DISIBEINT ELECTRONIC S.L, has been present n the feld of the manufacture of components for the ndustral automaton for more than 35 years, and mantans n constant evoluton

More information

Fiber length of pulp and paper by automated optical analyzer using polarized light (Five-year review of T 271 om-12) (no changes since Draft 1)

Fiber length of pulp and paper by automated optical analyzer using polarized light (Five-year review of T 271 om-12) (no changes since Draft 1) OTICE: Ths s a DRAFT of a TAPPI Standard n ballot. Although avalable for publc vewng, t s stll under TAPPI s copyrght and may not be reproduced or dstrbuted wthout permsson of TAPPI. Ths draft s OT a currently

More information

current activity shows on the top right corner in green. The steps appear in yellow

current activity shows on the top right corner in green. The steps appear in yellow Browzwear Tutorals Tutoral ntroducton Ths tutoral leads you through the basc garment creaton process usng an llustrated step by step approach. Each slde shows the actual applcaton at the stage of the acton

More information

EPLC9600-PID QUADRO(96x96 1/4 DIN) 4 Channel PID Controller

EPLC9600-PID QUADRO(96x96 1/4 DIN) 4 Channel PID Controller EPLC9600-PID QUADRO(96x96 1/4 DIN) 4 Channel PID Controller EPLC9600-PID QUADRO 96 x 96 DIN 1/4 4 Channel PID Controller - 128 x 64 Graphcal LCD dsplay - 4 Thermocouple (J, K, L, R or S type) sensor nputs

More information

Product Information. Long-stroke gripper PEH

Product Information. Long-stroke gripper PEH Product Informaton PEH PEH Flexble. Hgh Performance Densty. Bus capable. PEH long-stroke grpper Servo-electrc 2-fnger parallel grpper wth long jaw stroke for large parts and dverse parts spectrum Feld

More information

vacon 20 complete user manual ac drives Phone: Fax: Web: -

vacon 20 complete user manual ac drives Phone: Fax: Web:  - vacon 20 ac drves complete user manual Table of contents Document: DPD00716E1 Release date: 08.03.2013 Software package: FW0107V008.vcx 1.Safety 1 1.1Warnngs 1 1.2Safety nstructons 3 1.3Earthng and earth

More information

Absco Workshop Shed Model: 45302WK

Absco Workshop Shed Model: 45302WK Absco Workshop Shed Model: FRONT: 4.48m SIDE: 3.0m HEIGHT: 2.m CONCRETE SLAB 300mm 4580mm CONCRETE WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 25mm DEEP AROUND THE PERIMETER 00mm REBATED

More information

Terminating Tools

Terminating Tools Termnatng Tools 2-231652- 5 Instructon Sheet and 2-231652- 9 for 408-9770 DEConnect Modular Plugs 29 NOV 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually

More information

Calculation of the received voltage due to the radiation from multiple co-frequency sources

Calculation of the received voltage due to the radiation from multiple co-frequency sources Rec. ITU-R SM.1271-0 1 RECOMMENDATION ITU-R SM.1271-0 * EFFICIENT SPECTRUM UTILIZATION USING PROBABILISTIC METHODS Rec. ITU-R SM.1271 (1997) The ITU Radocommuncaton Assembly, consderng a) that communcatons

More information

H 2 S CO CH 4. Detective Net User & Operator Manual. Detective Net

H 2 S CO CH 4. Detective Net User & Operator Manual. Detective Net H 2 S CO CH 4 Detectve Net User & Operator Manual Detectve Net M070019/ENG Issue 3 Aug 2015 NAVIGATION INSTRUCTIONS The symbols n the left-hand margn of each page of the manual wll enable you to carry

More information

Connector Assemblies 06 JUN 11 Rev C

Connector Assemblies 06 JUN 11 Rev C Applcaton Specfcaton Power Seres 50 114-13071 Connector Assembles 06 JUN 11 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and nches]. Unless otherwse

More information

Uncertainty in measurements of power and energy on power networks

Uncertainty in measurements of power and energy on power networks Uncertanty n measurements of power and energy on power networks E. Manov, N. Kolev Department of Measurement and Instrumentaton, Techncal Unversty Sofa, bul. Klment Ohrdsk No8, bl., 000 Sofa, Bulgara Tel./fax:

More information

Operator's Manual. PCB Separator MAESTRO 4S

Operator's Manual. PCB Separator MAESTRO 4S Operator's Manual PCB Separator MAESTRO 4S 2 Operator's Manual - Translaton of the Orgnal Verson for the followng products Descrpton PCB Separator Type MAESTRO 4S Edton: 10/2017 Part No.: 9009613 Copyrght

More information