Mobile Radio Propagation Channel Models
|
|
- Nelson Higgins
- 6 years ago
- Views:
Transcription
1 Wireless Information Transmission System Lab. Mobile Radio Propagation Channel Models Institute of Communications Engineering National Sun Yat-sen University
2 Table of Contents Introduction Propagation Path Loss Model Friis Free Space Model Hata Model Large Scale Propagation Model Lognormal Distribution Small scale Propagation Model Multipath Delay Spread vs. Coherent Bandwidth Flat Fading vs. Frequency Selective Fading Narrowband vs. Wideband
3 Doppler s Effect Table of Contents Doppler s Shift vs. Coherent Time Fast Fading vs. Slow Fading. Rayleigh Distribution Level Crossing Rate Ricean Distribution Computer Simulation of Multipath Interference Channel Models in WCDMA Fading Counteraction Diversity Schemes Downlink Transmit Diversity in WCDMA 3
4 Wireless Information Transmission System Lab. Introduction Institute of Communications Engineering National Sun Yat-sen University
5 Introduction In general, there are two prevalent types of modeling of electromagnetic wave propagation. The first is what might be termed site-specific modeling or deterministic modeling, and attempts to model the exact interaction of the EM wave in the specific environment of interest. A second type of modeling attempts to model the relevant statistics of the received signal and may be called statistical modeling. This type is particularly useful in communication system development where the system must work in a wide variety of environments. 5
6 Main Components of Radio Propagation Propagation Path Loss. ( ~ 1/r in free space) Large Scale: Propagation models that predict the strength for an arbitrary separation distance. Small Scale: Propagation models that characterize the rapid fluctuation of the received signal strength over very short travel distance (~λ ) or short time duration (~s). 6
7 Large-Scale Propagation Models Propagation models that predict the mean signal strength for an arbitrary transmitter-receiver (T-R) separation distance are useful in estimating the radio coverage area of a transmitter. They characterize signal strength over large T-R (transmitter receiver) separation distances (several hundreds or thousands of meters). 7
8 Small-Scale Propagation Models Small-scale fading is used to describe the rapid fluctuation of the amplitude of a radio signal over a short period of time or travel distance. Fading is caused by interference between two or more versions of the transmitted signal which arrive at the receiver at slightly different time. These waves, called multi-path waves, combine at the receiver antenna to give a resultant signal which can vary widely in amplitude and phase. 8
9 Small-Scale Propagation Models The received signal power may vary by as much as three or four orders of magnitude (30 or 40 db) when the receiver is moved by only a fraction of a wavelength. Typically, the local average received power is computed by averaging signal measurements over a measurement track of 5λ to 40 λ. Hint : with f = 1 GHz ~ GHz, λ = c f = 30cm ~ 15cm 9
10 Small-Scale vs. Large-Scale Fading 10
11 Wireless Information Transmission System Lab. Propagation Path Loss Model Institute of Communications Engineering National Sun Yat-sen University
12 Free Space Propagation Model The free space propagation model is used to predict received signal strength when the transmitter and receiver have a clear, unobstructed line-of-sight (LOS) path between them. e.g. satellite, microwave ling-of-sight radio link. As with most large-scale radio wave propagation models, the free space model predicts that received power decays as a function of the T-R separation distance raised to some power. 1
13 PG t tgrλ Pr ( d) = (4π ) d L P t G G Friis Free Space Equation : transmitted power. P ( d) : received power which is a function of the r t r T - R separation. : the transmitter antenna gain. : the receiver antenna gain. d : the T - R separation distance in meters. L : the system loss factor not related to propagation. λ : the wavelength in meters. 13
14 Friis Free Space Equation The gain of an antenna is related to its effective aperture, A e, by: 4πA G = e λ The effective aperture A e is related to the physical size of the antenna. The miscellaneous losses L (L 1) are usually due to transmission line attenuation, filter losses, and antenna losses in the communication system. L=1 indicates no loss in the system hardware. 14
15 Log-distance Path Loss Model n d PL( d ) d0 PL( db) PL( d0 ) 10n log d = + d0 15
16 L 50 ( urban)( db) = 13.8logh te a( h Hata Model re ) An empirical formulation of the graphical path loss data provided by Okumura Valid from 150M to 1500Mhz. h te : 30m ~ 00m (base station antenna height) h re : 1m~10m (mobile antenna height) d : T-R separation distance (in km) a (h re ) : correction factor for effective mobile antenna height log + ( logh f c te ) logd
17 Hata Model For small to medium sized city: a( h ) = (1.1log f 0.7) h (1.56log f 0.8) db re For large city: ah ( ) = 8.9(log1.54 h ) 1.1 db for f 300MHz For suburban area: c re re c ah h db f MHz ( re) = 3.(log11.75 re) 4.97 for c 300 L50 ( db) = L50 ( urban) [log( f c / 8)] 5.4 For open rural areas: L50( db) = L50( urban) 4.78(log f c ) 18.33log fc re c 17
18 Hata Model in PCS Band Extension of Hata model to GHz. L50 ( urban )( db) = log a( h ) + ( log h ) log C M h h re te f 10 c 13.8 log d + = 0dB for medium sized city and suburban areas = 3dB for metropolitan centers f :1500MHz ~ 000MHz te re : 30m ~ 00m :1m ~ 10m d :1km ~ 0km C M h te 18
19 Wireless Information Transmission System Lab. Large Scale Propagation Model Institute of Communications Engineering National Sun Yat-sen University
20 Shadowing Effect Lognormal Distribution When reaching the mobile station, the radio wave will have traveled through different obstructions such as buildings, tunnels, hills, trees, etc. The received signal R, when measured in decibels, has a normal density function. Thus R is described by lognormal distribution. 1 ( ln r m) / σ e ( r 0) The PDF of R is: p( r) = πσr 0 ( r < 0) d PL ( d ) = PL ( d ) + X σ = PL ( d ) n X σ d log + 0 X σ : a zero-mean Gaussian distributed random variable (db) with standard deviation 4-10 db. 0
21 Shadow Fading: attenuation 10 ζ 10 Correlation of Path Loss: (from Viterbi, Principles of Spread Spectrum Communications) ζ = a ξ + b ξ a + b = Correlation of Path Loss mobile 1, base station E( ζ ) = E( ξ ) = E( ξ ) = 0, mobile base station Var ζ Var ξ Var ξ σ ( ) = ( mobile ) = ( base station ) =. 1
22 Wireless Information Transmission System Lab. Small Scale Propagation Model Institute of Communications Engineering National Sun Yat-sen University
23 Small Scale Fading -- 1 Problem 1: multi-path induces delay spread. 3
24 Impulse Response Model of a Multipath Channel A mobile radio channel may be modeled as a linear filter with a time varying impulse response, where the time variation is due to receiver motion in space. The filtering nature of the channel is caused by the summation of amplitudes and delays of the multiple arriving waves at any instant of time. 4
25 Channel Impulse Response Due to the different multipath waves which have propagation delays which vary over different spatial locations of the receiver, the impulse response of the linear time invariant channel should be a function of the position of the receiver. ydt (, ) = xt ( ) hdt (, ) = x( τ) hdt (, τ) dτ where hdt (, ) is the channel impulse resonse. xt ( ) is the transmitted signal. y( dt, ) is the received signal at position d. 5
26 Multipath Radio Channel 6
27 Multipath Propagation Effect 7
28 Measured Multipath Power Delay Profiles From a 900 MHz cellular system in San Fancisco. 8
29 Measured Multipath Power Delay Profiles Inside a grocery store at 4 GHz. 9
30 Delay Spread Delay spread and coherence bandwidth are used to describe the time dispersive nature of the channel. Received Signal: h ( t ) = n i = 1 a i δ ( t Delay Spread στ corresponds to standard deviation of T i. T i ) Excess delay is the relative delay of the i-th multipath component as compared to the first arriving component. 30
31 31 Time Dispersion Parameters Mean Excess Delay: the first moment of the power delay profile. RMS (room mean square) Delay Spread: the square root of the second central moment of the power delay profile. = = k k k k k k k k k k P P a a ) ( ) ( τ τ τ τ τ ) (τ τ σ τ = = = k k k k k k k k k k P P a a ) ( ) ( τ τ τ τ τ
32 Time Dispersion Parameters These delays are measured relative to the first detectable signal arriving at the receiver at τ 0 =0. The equations in the previous page do not rely on the absolute power level of P(τ), but only the relative amplitudes of the multipath components within P(τ). Typical values of rms delay spread are on the order of microseconds in outdoor mobile radio channels and on the order of nanoseconcds in indoor radio channels. 3
33 Typical Measured Values of RMS Delay Spread 33
34 Maximum Excess Delay Maximum Excess Delay (ΧdB) = the time delay during which multipath energy falls to ΧdB below maximum. Maximum Excess Delay (ΧdB) can also be defined as τ x -τ 0, where τ 0 is the first arriving signal; τ x is the maximum delay at which a multipath component is within X db of the strongest arriving multipath signal. The value of τ x is sometimes called the excess delay spread of a power delay profile. 34
35 Example of An Indoor Power Delay Profile 35
36 Coherence Bandwidth Time domain focus on excess delay. Frequency domain focus on coherence bandwidth B c. B c is defined related to rms delay spread 1/(B c ) B c (Coherence Bandwidth) A statistical measure of the range of frequencies over which the channel can be considered flat (i.e. a channel which passes all spectral components with approximately equal gain and linear phase.). The range of frequencies over which two frequency components have a strong potential for amplitude correlation. Two sinusoids with frequency separation greater than Bc are affected quite differently by the channel. 36
37 Coherence Bandwidth Version 1: the bandwidth over which the frequency correlation is above 0.9 B c = 1 50 σ τ Version : the bandwidth over which the frequency correlation is above 0.5 B c = 1 5 σ τ 37
38 Types of Small-Scale Fading Based on multi-path time delay spread Flat Fading (narrowband system) BW of signal < BW of channel Delay spread < Symbol period Frequency Selective Fading (wideband system) BW of signal > BW of channel Delay spread > Symbol period 38
39 Wideband v.s. Narrowband 39
40 Flat Fading Signal undergoes flat fading if S C T s : reciprocal BW (e.g. symbol period) B s : BW of the TX modulation σ τ : rms delay spread B c : Coherence BW 40 B << B and T S >> σ τ
41 Flat Fading The mobile radio channel has a constant gain and linear phase response over a bandwidth which is greater than the bandwidth of the transmitted signal. The multipath structure of the channel is such that the spectral characteristics of the transmitted signal are preserved at the receiver. The strength of the received signal changes with time, due to fluctuations in the gain of the channel caused by multipath. 41
42 Flat Fading Typical flat fading channels cause deep fades, and thus may require 0 or 30 db more transmitter power to achieve low bit error rates during times of deep fades as compared to systems operating over nonfading channels. Also known as amplitude varying channel. Also referred to as narrowband channels since the bandwidth of the applied signal is narrow as compared to the channel flat fading bandwidth. The most common amplitude distribution of flat fading channel is the Rayleigh distribution. 4
43 Frequency Selective Fading Signal undergoes frequency selective fading if B > B and T S < στ S C 43
44 Frequency Selective Fading The channel possesses a constant-gain and linear phase response over a bandwidth that is smaller than the bandwidth of transmitted signal. The received signal includes multiple versions of the transmitted waveform which are attenuated and delayed in time. The channel induces inter-symbol interference. Certain frequency components in the received signal spectrum have greater gains than others. Also known as wideband channels. M-ray Rayleigh fading model is usually used for analyzing frequency selective small-scale fading. 44
45 Small Scale Fading -- Problem : moving receiver induces fading effects (Doppler shift) for each ray path. 45
46 Doppler Effect Doppler is a frequency shift, cause by movement of the mobile antenna relative to the base station - Δf = V/λ (at 50 km/h and 900 MHz, Δf = 08 Hz) f f - f V f + f 46
47 47 Doppler Shift / Spread θ cosθ cos t v d l = = θ λ π λ π φ cos Phase Change : t v l = = θ λ φ π cos 1 : Doppler Shift v t f d = =
48 Doppler Spread and Coherence Time Delay spread and coherence bandwidth do not offer information about the time varying nature of the channel caused by either relative motion between the mobile and base station, of by movement of objects in the channel. Doppler spread and coherence time are parameters which describe the time varying nature of the channel in a small-scale. Doppler spread B D is a measure of the spectral broadening caused by the time rate of change of the mobile radio channel and is defined as the range of frequencies over which the received Doppler spectrum is essentially non-zero. When a pure sinusoidal tone of frequency f c is transmitted, the received signal spectrum, called the Doppler spectrum, will be in the range f c -f d to f c +f d, where f d is Doppler shift. 48
49 Coherence Time Coherence time T c is the time domain dual of Doppler spread and is used to characterize the time varying nature of the frequency dispersiveness of the channel in the time domain. Coherence time is a statistical measure of the time duration over which the channel impulse response is essentially invariant. Coherence time is the time duration over which two received signals have a strong potential for amplitude correlation. 49
50 Version 1: T 1 c Coherence Time ƒ m : the maximum Doppler shift, ƒ m = ν/λ f m Version : the time over which the time correlation > 0.5 T 9 16π c f m Version 3: Geometric mean of version 1 and version. T c = 9 16πf = m 0.43 f m 50
51 Doppler Power Spectrum 51
52 Types of Small-Scale Fading Based on Doppler Spread Fast Fading High Doppler spread. Coherence time < Symbol Period. Channel variations faster than base-band signal variations Slow Fading Low Doppler spread. Coherence time > Symbol period. Channel variations slower than base-band signal variations 5
53 Fast Fading T S >T C and B S <B D. The channel impulse response changes rapidly within the symbol duration. The coherence time of the channel is smaller than the symbol period of the transmitted signal. Signal distortion due to fast fading increases with increasing Doppler spread relative to the bandwidth of the transmitted signal. Fast fading only deals with the rate of change of the channel due to motion. In practice, fast fading only occurs for very low data rates (or very fast motion speed). 53
54 Slow Fading T S <<T C and B S >>B D Channel impulse response changes at a rate much slower than the transmitted baseband signal s(t). The channel may be assumed to be static over one or several reciprocal bandwidth intervals. The Doppler spread of the channel is much less than the bandwidth of the baseband signal. The velocity of the mobile and the baseband signaling determines whether a signal undergoes fast fading or slow fading. 54
55 Type of Small-Scale Fading 55
56 Type of Small-Scale Fading 56
57 Wireless Information Transmission System Lab. Rayleigh Distribution Institute of Communications Engineering National Sun Yat-sen University
58 Rayleigh Distribution Rayleigh distributions are commonly used to describe the statistical time varying nature of the received envelope of a flat fading signal, or the envelope of an individual multipath component. Envelope of the sum of two quadrature Gaussian noise signals obeys a Rayleigh distribution. 58
59 Typical Rayleigh Fading Envelope 59
60 60 Rayleigh Distribution Consider a carrier signal s at a frequency ω 0 and with an amplitude a: The received signal s r is the sum of n waves: exp( 0 t) j a s ω = [ ] [ ] θ θ θ θ θ θ θ θ θ θ ω θ ω sin cos where : sin and cos have : We sin cos ) exp( Define : ) exp( ) exp( where ) ( exp ) ( exp r y r x y x r a y a x jy x a j a j r j a j r t j r t j a s n i i i n i i i n i i i n i i i n i i i n i i i r = = + = + + = = + + = = = = = = =
61 Rayleigh Distribution Because (1) n is usually very large, () the individual amplitudes a i are random, and (3) the phases θ i have a uniform distribution, it can be assumed that (from the central limit theorem) x and y are both Gaussian variables with means equal to zero and variance σ x = σ y Because x and y are independent random variables, the joint distribution p(x,y) is 1 x + y p( x, y) = p( x) p( y) = exp πσ σ The distribution p(r,θ) can be written as a function of p(x,y) : 61 σ p ( r, θ ) = J p( x, y)
62 Rayleigh Distribution x/ r x/ θ cosθ rsinθ r r ; (, θ) exp J = = r p r = y/ r y/ θ sinθ rcosθ πσ σ Thus, the Rayleigh distribution has a pdf: π r r exp 0 r pr () = pr (, θ) dθ = σ σ 0 0 otherwise The probability that the envelope of the received signal does not exceed a specified value R is given by the corresponding cumulative distribution function (CDF) R R P( R) = Pr( r R) = p( r) dr = 1 exp 0 σ 6
63 Rayleigh Distribution Mean: π r mean = E[ r] = rp( r) dr = σ = σ 0 Variance: σ π σ = [ ] [ ] = r E r E r r p( r) dr π = σ = 0.49σ Median value of r is found by solving: Mean squared value: Most likely value = max { p(r) } = σ = r median E[ r ] = r p( r) dr = σ r median 0 p( r) dr =1.177σ
64 Rayleigh Probability Density Function 64
65 Level Crossing and Fading Statistics The level crossing rate (LCR) is defined as the expected rate at which the Rayleigh fading envelope, normalized to the local rms signal level, crosses a specified level in a positive-going direction. Useful for designing error control codes and diversity. Relate the time rate of change of the received signal to the signal level and velocity of the mobile. 65
66 Level Crossing Rate (LCR) The number of level crossings per second is given by: N = r p( R, r) d r = π f ρe R ρ m 0 r is the time derivative of r( t) (i.e. the slope) p( R, r) is the joint density function of r and r at r = R f m is the maximum Doppler frequency ρ = R / Rrms is the value of the specified level R, normalized to the local rms amplitude of the fading envelope. Clarke, R. H., A Statistical Theory of Mobile-Radio Reception, Bell Systems Technical Journal, Vol. 47, pp ,
67 Average Fade Duration Average fade duration is defined as the average period of time for which the received signal is below a specified level R. For a Rayleigh fading signal, this is given by: 1 Pr [ ] τ = r R N R where Pr[r R] is the probability that the received signal r is less than R and is given by 1 Pr[ r R] = τ i T where τ i is the duration of the fade and T is the observation interval of the fading signal. i 67
68 Average Fade Duration The probability that the received signal r is less than the threshold R is found fro the Rayleigh distribution as: Pr[ r R] = R 0 p( r) dr = 1 exp( ρ ) ρ = R σ where p(r) is the pdf of a Rayleigh distribution. The average fade duration as a function of ρ and f m can be expressed as ρ e 1 τ = ρ f π m 68
69 Average Fade Duration The average duration of a signal fade helps determine the most likely number of signaling bits that may be lost during a fade. Average fade duration primarily depends upon the speed of the mobile, and decreases as the maximum Doppler frequency f m becomes large. 69
70 Wireless Information Transmission System Lab. Ricean Distribution Institute of Communications Engineering National Sun Yat-sen University
71 Ricean Fading Distribution When there is a dominant stationary (non-fading) signal component present, such as a line-of-sight propagation path, the small-scale fading envelope distribution is Ricean. s r = scattered waves r' exp[ j( ω t + θ )] + [( x + A) + r = ( x + A) + y x + A = r cosθ y = r sinθ 0 jy]exp( direct waves Aexp( jω t) jω t) 0 r 0 exp[ j( ω t 0 + θ )] 71
72 7 Ricean Fading Distribution By following similar steps described in Rayleigh distribution, we obtain: ( ) = = = < + = ! function. - order Bessel zeroth modified the is cos exp 1 where 0 for 0 0 r 0, A for exp ) ( i i i r r r r r i x (x) I d Ar Ar I ) (r Ar I A r r r p θ σ θ π σ σ σ σ π
73 Ricean Fading Distribution The Ricean distribution is often described in terms of a parameter K which is defined as the ratio between the deterministic signal power and the variance of the multipath. It is given by K=A /(σ ) or in terms of db: A K( db) = 10 log [db] σ The parameter K is known as the Ricean factor and completely specifies the Ricean distribution. As A 0, K - db, and as the dominant path decreases in amplitude, the Ricean distribution degenerates to a Rayleigh distribution. 73
74 Ricean Distribution 74
75 Ricean Distribution 75
76 Wireless Information Transmission System Lab. Computer Simulation of Multi-path Interference Reference: Microwave Mobile Communications, by W.C. Jakes, pp Institute of Communications Engineering National Sun Yat-sen University
77 Frequency Selective Fading Channel Rayleigh fading is usually adopted for flat fading channel model. Frequency selective fading channel model is usually modeled as the sum of several flat fading channels with different delays. 77
78 Spatial Correlations at the Base Station Scattering model for spatial correlations at the base station. 78
79 Computer Simulation of Rayleigh Fading Simulator that duplicates mobile radio spectrum Producing random phase modulation, a Rayleigh fading envelope, and a time-averaged, discrete approximation to the desired power spectrum. Simulation inputs: Carrier frequency. Mobile velocity. Sampling rate. The number of frequency components (N 0 ) needed is at least 8 (N is at least 34 where N 0 =0.5*(N/-1) and N/ is an odd integer). 79
80 Computer Simulation of Rayleigh Fading Simulator that duplicates mobile radio spectrum 80
81 Wireless Information Transmission System Lab. Channel Models in WCDMA Institute of Communications Engineering National Sun Yat-sen University
82 (I) Static Propagation Condition The propagation for the static performance measurement is an Additive White Gaussian Noise (AWGN) environment. No fading or multi-paths exist for this propagation model. 8
83 (II) Multi-Path Fading Propagation Conditions Table B.1 shows propagation conditions that are used for the performance measurements in multi-path fading environment. All taps have classical Doppler spectrum, defined as: 1 S ( f ) f [ fd, fd] 1 f f ( ) Table B.1: Propagation Conditions for Multi path Fading Environments D Case 1, speed 3km/h Case, speed 3 km/h Case 3, 10 km/h Case 4, 50 km/h Relative Delay [ns] Average Power [db] Relative Delay [ns] Average Power [db] Relative Delay [ns] Average Power [db] Relative Delay [ns] Average Power [db]
84 P 0 (III) Moving Propagation Conditions The dynamic propagation conditions for the test of the base band performance are non-fading channel models with two taps. The moving propagation condition has two tap, one static, Path0, and one moving, Path1. The time difference between the two paths is according Equation (B.1). The parameters for the equation are shown in Table B.. The taps have equal strengths and equal phases. A P 1 τ = B + ( 1+ sin( ω t) ) (B.1) Table B.: Parameters for moving propagation τ t 0 t 1 Figure B.1: The moving propagation conditions A B Δω 5 µs 1 µs s -1 84
85 (IV) Birth-Death Propagation Conditions The dynamic propagation conditions for the test of the baseband performance is a non-fading propagation channel with two taps. The moving propagation conditions has two taps, Path1 and Path which alternate between 'birth' and 'death'. The positions the paths appear are randomly selected with an equal probability rate and are shown in Figure B.. P1 P P1 P1 P P P1 P Figure B.: Birth death propagation sequence 85
86 Birth-Death Propagation Conditions 1. Two paths, Path1 and Path are randomly selected from the group [-5, -4, -3, -, -1, 0,1,, 3, 4, 5] µs. The paths have equal magnitudes and equal phases.. After 191 ms, Path1 vanishes and reappears immediately at a new location randomly selected from the group [-5, - 4, -3, -, -1, 0,1,, 3, 4, 5] µs but excludes the point Path. The magnitudes and the phases of the tap coefficients of Path 1 and Path shall remain unaltered. 3. After an additional 191 ms, Path vanishes and reappears immediately at a new location randomly selected from the group [-5, -4, -3, -, -1, 0,1,, 3, 4, 5] µs but excludes the point Path1. The magnitudes and the phases of the tap coefficients of Path 1 and Path shall remain unaltered. 4. The sequence in ) and 3) is repeated. 86
87 Summary of Base Station Performance Targets Physical channel Measurement channel Static Multi-path Case 1 Multi-path Case Multi-path Case 3 Moving Birth / Death Performance metric 1. kbps BLER<10 - BLER<10 - BLER<10 - BLER<10 - BLER< BLER< 64 kbps BLER< 10-1,10 - BLER< 10-1, 10 - BLER< 10-1,10 - BLER< 10-1, 10 -,10-3 BLER< BLER< DCH 144 kbps BLER< 10-1,10 - BLER< 10-1,10 - BLER< 10-1,10 - BLER< 10-1, 10 -, kbps BLER< 10-1,10 - BLER< 10-1,10 - BLER< 10-1,10 - BLER< 10-1, 10 -,
88 Performance Requirements in AWGN Channel Measurement channel 1. kbps 64 kbps 144 kbps 384 kbps Received E b /N 0 n.a. 5.1 db 1.5 db 1.7 db 0.8 db 0.9 db 0.9 db 1.0 db Required BLER < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10-88
89 Performance requirements in multipath Case 1 channel Measurement channel 1. kbps 64 kbps 144 kbps 384 kbps Received E b /N 0 n.a db 6. db 9. db 5.4 db 8.4 db 5.8 db 8.8 db Required BLER < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10-89
90 Performance requirements in multipath Case channel Measurement channel 1. kbps 64 kbps 144 kbps 384 kbps Received E b /N 0 n.a. 9.0 db 4.3 db 6.4 db 3.7 db 5.6 db 4.1 db 6.1 db Required BLER < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10 - < 10-1 < 10-90
91 Performance requirements in multipath Case 3 channel Measurement channel 1. kbps 64 kbps 144 kbps 384 kbps Received E b /N 0 n.a. 7. db 8.0 db 3.4 db 3.8 db 4.1 db.8 db 3. db 3.6 db 3. db 3.6 db 4. db Required BLER < 10-1 < 10 - < 10-3 < 10-1 < 10 - < 10-3 < 10-1 < 10 - < 10-3 < 10-1 < 10 - <
92 Performance requirements in multipath Case 4 channel Measurement channel 1. kbps 64 kbps 144 kbps 384 kbps Received E b /N 0 n.a. 10. db 11.0 db 6.4 db 6.8 db 7.1 db 5.8 db 6. db 6.6 db 6. db 6.6 db 7. db Required BLER < 10-1 < 10- < 10-3 < 10-1 < 10- < 10-3 < 10-1 < 10- < 10-3 < 10-1 < 10- <
93 Performance requirements in moving channel Measurement channel 1. kbps 64 kbps Received E b /N 0 n.a. 5.7 db.1 db. db Required BLER < 10-1 < 10 - < 10-1 < 10-93
94 Performance requirements in birth/death channel Measurement channel Received E b /N 0 Required BLER 1. kbps n.a. < kbps 7.7 db 4.1 db < 10 - < db < 10-94
95 Wireless Information Transmission System Lab. Fading Counteraction Diversity Schemes Institute of Communications Engineering National Sun Yat-sen University
96 Fading Counteractions Long-Term (large scale) Fading Counteraction: Macroscopic diversity (Space diversity) S-diversity S+I-diversity S/I-diversity 96
97 Fading Counteraction Short-Term (small scale) Fading Counteraction: Microscopic diversity. Space diversity - spacing is between receiving antennas. Polarization: orthogonality of the polarized wave components. Angle: directional antenna. Frequency: two or more different carriers. Time: time separation. Hopping: frequency hopping and time hopping. 97
98 Switched Combining Combining Schemes Pure Selection: the received signals are continuously monitored so that the best signal can be selected. Threshold Selection: the received signals are scanned in a sequential order, and the first signal with a power level above a certain threshold is selected. Gain Combining Maximal Ratio Combining (MRC): each one of the M signals has a gain proportional to its own signal-to-noise ratio. Equal Gain Combining: all of the signals have a gain equal to one. 98
99 Wireless Information Transmission System Lab. Downlink Transmit Diversity in WCDMA Institute of Communications Engineering National Sun Yat-sen University
100 Downlink Transmit Diversity in WCDMA Application of Tx diversity modes on downlink physical channel types O : can be applied, : not applied Physical channel type TSTD Open loop mode STTD Closed loop Mode P-CCPCH O SCH O S-CCPCH O DPCH O O PICH O PDSCH O O AICH O CSICH O AP-AICH - O - CD/CA-ICH - O - DL-DPCCH for CPCH - O O Simultaneous use of STTD and closed loop modes on the same physical channel is not allowed. 100
101 Space Time Transmit Diversity (STTD) The STTD encoding is optional in UTRAN. STTD support is mandatory at the UE. b 0 b 1 b b 3 Antenna 1 b 0 b 1 b b 3 Channel bits -b b 3 b 0 -b 1 Antenna STTD encoded channel bits for antenna 1 and antenna. 101
102 Time Switched Transmit Diversity Slot #0 Slot #1 Slot #14 Primary SCH ac p ac p ac p Secondary SCH ac s i,0 ac s i,1 ac s i,14 56 chips 560 chips One 10 ms SCH radio frame Structure of Synchronisation Channel (SCH) 10
103 Time Switched Transmit Diversity Slot #0 Slot #1 Slot # Slot #14 Antenna 1 ac p (Tx OFF) ac p ac p ac s i,0 (Tx OFF) ac s i, ac s i,14 Antenna (Tx OFF) ac p (Tx OFF) (Tx OFF) (Tx OFF) ac s i,1 (Tx OFF) (Tx OFF) Structure of SCH transmitted by TSTD scheme 103
104 Downlink Transmitter Structure to Support Closed Loop Mode Transmit Diversity for DPCH Transmission Spread/scramble w 1 CPICH 1 Ant 1 DPCCH DPDCH DPCH Ant w CPICH w 1 w Weight Generation Determine FBI message from Uplink DPCCH 104
Mobile Radio Propagation Channel Models
Wireless Information Transmission System Lab. Mobile Radio Propagation Channel Models Institute of Communications Engineering National Sun Yat-sen University Table of Contents Introduction Propagation
More informationChannel. Muhammad Ali Jinnah University, Islamabad Campus, Pakistan. Multi-Path Fading. Dr. Noor M Khan EE, MAJU
Instructor: Prof. Dr. Noor M. Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office), 186 (Lab) Fax: +9
More informationEENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss
EENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss Introduction Small-scale fading is used to describe the rapid fluctuation of the amplitude of a radio
More informationMulti-Path Fading Channel
Instructor: Prof. Dr. Noor M. Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office), 186 (Lab) Fax: +9
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2003 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2004 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2005 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationDigital Communications over Fading Channel s
over Fading Channel s Instructor: Prof. Dr. Noor M Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office),
More informationMobile Radio Propagation: Small-Scale Fading and Multi-path
Mobile Radio Propagation: Small-Scale Fading and Multi-path 1 EE/TE 4365, UT Dallas 2 Small-scale Fading Small-scale fading, or simply fading describes the rapid fluctuation of the amplitude of a radio
More informationMuhammad Ali Jinnah University, Islamabad Campus, Pakistan. Fading Channel. Base Station
Fading Lecturer: Assoc. Prof. Dr. Noor M Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office), 186 (ARWiC
More informationWireless Channel Propagation Model Small-scale Fading
Wireless Channel Propagation Model Small-scale Fading Basic Questions T x What will happen if the transmitter - changes transmit power? - changes frequency? - operates at higher speed? Transmit power,
More informationThe Radio Channel. COS 463: Wireless Networks Lecture 14 Kyle Jamieson. [Parts adapted from I. Darwazeh, A. Goldsmith, T. Rappaport, P.
The Radio Channel COS 463: Wireless Networks Lecture 14 Kyle Jamieson [Parts adapted from I. Darwazeh, A. Goldsmith, T. Rappaport, P. Steenkiste] Motivation The radio channel is what limits most radio
More informationCHAPTER 2 WIRELESS CHANNEL
CHAPTER 2 WIRELESS CHANNEL 2.1 INTRODUCTION In mobile radio channel there is certain fundamental limitation on the performance of wireless communication system. There are many obstructions between transmitter
More informationWIRELESS COMMUNICATION TECHNOLOGIES (16:332:546) LECTURE 5 SMALL SCALE FADING
WIRELESS COMMUNICATION TECHNOLOGIES (16:332:546) LECTURE 5 SMALL SCALE FADING Instructor: Dr. Narayan Mandayam Slides: SabarishVivek Sarathy A QUICK RECAP Why is there poor signal reception in urban clutters?
More informationNarrow- and wideband channels
RADIO SYSTEMS ETIN15 Lecture no: 3 Narrow- and wideband channels Ove Edfors, Department of Electrical and Information technology Ove.Edfors@eit.lth.se 2012-03-19 Ove Edfors - ETIN15 1 Contents Short review
More informationChapter 5 Small-Scale Fading and Multipath. School of Information Science and Engineering, SDU
Chapter 5 Small-Scale Fading and Multipath School of Information Science and Engineering, SDU Outline Small-Scale Multipath Propagation Impulse Response Model of a Multipath Channel Small-Scale Multipath
More informationRevision of Lecture One
Revision of Lecture One System block Transceiver Wireless Channel Signal / System: Bandpass (Passband) Baseband Baseband complex envelope Linear system: complex (baseband) channel impulse response Channel:
More informationRevision of Lecture One
Revision of Lecture One System blocks and basic concepts Multiple access, MIMO, space-time Transceiver Wireless Channel Signal/System: Bandpass (Passband) Baseband Baseband complex envelope Linear system:
More informationPart 4. Communications over Wireless Channels
Part 4. Communications over Wireless Channels p. 1 Wireless Channels Performance of a wireless communication system is basically limited by the wireless channel wired channel: stationary and predicable
More information9.4 Temporal Channel Models
ECEn 665: Antennas and Propagation for Wireless Communications 127 9.4 Temporal Channel Models The Rayleigh and Ricean fading models provide a statistical model for the variation of the power received
More informationCALIFORNIA STATE UNIVERSITY, NORTHRIDGE FADING CHANNEL CHARACTERIZATION AND MODELING
CALIFORNIA STATE UNIVERSITY, NORTHRIDGE FADING CHANNEL CHARACTERIZATION AND MODELING A graduate project submitted in partial fulfillment of the requirements For the degree of Master of Science in Electrical
More informationNarrow- and wideband channels
RADIO SYSTEMS ETIN15 Lecture no: 3 Narrow- and wideband channels Ove Edfors, Department of Electrical and Information technology Ove.Edfors@eit.lth.se 27 March 2017 1 Contents Short review NARROW-BAND
More informationChannel Modeling ETI 085
Channel Modeling ETI 085 Overview Lecture no: 9 What is Ultra-Wideband (UWB)? Why do we need UWB channel models? UWB Channel Modeling UWB channel modeling Standardized UWB channel models Fredrik Tufvesson
More informationUWB Channel Modeling
Channel Modeling ETIN10 Lecture no: 9 UWB Channel Modeling Fredrik Tufvesson & Johan Kåredal, Department of Electrical and Information Technology fredrik.tufvesson@eit.lth.se 2011-02-21 Fredrik Tufvesson
More informationSmall-Scale Fading I PROF. MICHAEL TSAI 2011/10/27
Small-Scale Fading I PROF. MICHAEL TSAI 011/10/7 Multipath Propagation RX just sums up all Multi Path Component (MPC). Multipath Channel Impulse Response An example of the time-varying discrete-time impulse
More informationText Book. References. Andrea Goldsmith, Wireless Communications, Cambridge University Press Wireless Communications
Ammar Abu-Hudrouss Islamic University Gaza ١ Course Syllabus Text Boo Andrea Goldsmith,, Cambridge University Press 005. References 1. Rappaport, : Principles and Practice, Prentice Hall nd Ed. D. N. C.
More informationNETW 701: Wireless Communications. Lecture 5. Small Scale Fading
NETW 701: Wireless Communications Lecture 5 Small Scale Fading Small Scale Fading Most mobile communication systems are used in and around center of population. The transmitting antenna or Base Station
More informationRECOMMENDATION ITU-R P The prediction of the time and the spatial profile for broadband land mobile services using UHF and SHF bands
Rec. ITU-R P.1816 1 RECOMMENDATION ITU-R P.1816 The prediction of the time and the spatial profile for broadband land mobile services using UHF and SHF bands (Question ITU-R 211/3) (2007) Scope The purpose
More informationUNIK4230: Mobile Communications Spring 2013
UNIK4230: Mobile Communications Spring 2013 Abul Kaosher abul.kaosher@nsn.com Mobile: 99 27 10 19 1 UNIK4230: Mobile Communications Propagation characteristis of wireless channel Date: 07.02.2013 2 UNIK4230:
More informationChannel Models. Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1
Channel Models Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1 Narrowband Channel Models Statistical Approach: Impulse response modeling: A narrowband channel can be represented by an impulse
More informationEITN85, FREDRIK TUFVESSON, JOHAN KÅREDAL ELECTRICAL AND INFORMATION TECHNOLOGY. Why do we need UWB channel models?
Wireless Communication Channels Lecture 9:UWB Channel Modeling EITN85, FREDRIK TUFVESSON, JOHAN KÅREDAL ELECTRICAL AND INFORMATION TECHNOLOGY Overview What is Ultra-Wideband (UWB)? Why do we need UWB channel
More informationMobile Communications
Mobile Communications Part IV- Propagation Characteristics Professor Z Ghassemlooy School of Computing, Engineering and Information Sciences University of Northumbria U.K. http://soe.unn.ac.uk/ocr Contents
More informationEmpirical Path Loss Models
Empirical Path Loss Models 1 Free space and direct plus reflected path loss 2 Hata model 3 Lee model 4 Other models 5 Examples Levis, Johnson, Teixeira (ESL/OSU) Radiowave Propagation August 17, 2018 1
More informationSimulation of Outdoor Radio Channel
Simulation of Outdoor Radio Channel Peter Brída, Ján Dúha Department of Telecommunication, University of Žilina Univerzitná 815/1, 010 6 Žilina Email: brida@fel.utc.sk, duha@fel.utc.sk Abstract Wireless
More informationEC 551 Telecommunication System Engineering. Mohamed Khedr
EC 551 Telecommunication System Engineering Mohamed Khedr http://webmail.aast.edu/~khedr 1 Mohamed Khedr., 2008 Syllabus Tentatively Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week
More informationPropagation Channels. Chapter Path Loss
Chapter 9 Propagation Channels The transmit and receive antennas in the systems we have analyzed in earlier chapters have been in free space with no other objects present. In a practical communication
More informationPerformance Evaluation Of Digital Modulation Techniques In Awgn Communication Channel
Performance Evaluation Of Digital Modulation Techniques In Awgn Communication Channel Oyetunji S. A 1 and Akinninranye A. A 2 1 Federal University of Technology Akure, Nigeria 2 MTN Nigeria Abstract The
More informationWideband Channel Characterization. Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1
Wideband Channel Characterization Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1 Wideband Systems - ISI Previous chapter considered CW (carrier-only) or narrow-band signals which do NOT
More informationApplication Note 37. Emulating RF Channel Characteristics
Application Note 37 Emulating RF Channel Characteristics Wireless communication is one of the most demanding applications for the telecommunications equipment designer. Typical signals at the receiver
More informationIEEE Working Group on Mobile Broadband Wireless Access <http://grouper.ieee.org/groups/802/mbwa>
2003-01-10 IEEE C802.20-03/09 Project Title IEEE 802.20 Working Group on Mobile Broadband Wireless Access Channel Modeling Suitable for MBWA Date Submitted Source(s)
More informationUnit 5 - Week 4 - Multipath Fading Environment
2/29/207 Introduction to ireless and Cellular Communications - - Unit 5 - eek 4 - Multipath Fading Environment X Courses Unit 5 - eek 4 - Multipath Fading Environment Course outline How to access the portal
More informationWIRELESS COMMUNICATIONS PRELIMINARIES
WIRELESS COMMUNICATIONS Preliminaries Radio Environment Modulation Performance PRELIMINARIES db s and dbm s Frequency/Time Relationship Bandwidth, Symbol Rate, and Bit Rate 1 DECIBELS Relative signal strengths
More informationChannel Modelling ETIM10. Channel models
Channel Modelling ETIM10 Lecture no: 6 Channel models Fredrik Tufvesson Department of Electrical and Information Technology Lund University, Sweden Fredrik.Tufvesson@eit.lth.se 2012-02-03 Fredrik Tufvesson
More informationSession2 Antennas and Propagation
Wireless Communication Presented by Dr. Mahmoud Daneshvar Session2 Antennas and Propagation 1. Introduction Types of Anttenas Free space Propagation 2. Propagation modes 3. Transmission Problems 4. Fading
More informationWireless Communication Fundamentals Feb. 8, 2005
Wireless Communication Fundamentals Feb. 8, 005 Dr. Chengzhi Li 1 Suggested Reading Chapter Wireless Communications by T. S. Rappaport, 001 (version ) Rayleigh Fading Channels in Mobile Digital Communication
More informationWireless Channel Modeling (Modeling, Simulation, and Mitigation)
Wireless Channel Modeling (Modeling, Simulation, and Mitigation) Dr. Syed Junaid Nawaz Assistant Proessor Department o Electrical Engineering COMSATS Institute o Inormation Technology Islamabad, Paistan.
More informationLevel 6 Graduate Diploma in Engineering Wireless and mobile communications
9210-119 Level 6 Graduate Diploma in Engineering Wireless and mobile communications Sample Paper You should have the following for this examination one answer book non-programmable calculator pen, pencil,
More informationLecture 7/8: UWB Channel. Kommunikations
Lecture 7/8: UWB Channel Kommunikations Technik UWB Propagation Channel Radio Propagation Channel Model is important for Link level simulation (bit error ratios, block error ratios) Coverage evaluation
More informationChapter 3. Mobile Radio Propagation
Chapter 3 Mobile Radio Propagation Based on the slides of Dr. Dharma P. Agrawal, University of Cincinnati and Dr. Andrea Goldsmith, Stanford University Propagation Mechanisms Outline Radio Propagation
More informationMSIT 413: Wireless Technologies Week 3
MSIT 413: Wireless Technologies Week 3 Michael L. Honig Department of EECS Northwestern University January 2016 Why Study Radio Propagation? To determine coverage Can we use the same channels? Must determine
More informationMobile Communications
Mobile Communications Wen-Shen Wuen Trans. Wireless Technology Laboratory National Chiao Tung University WS Wuen Mobile Communications 1 Outline Outline 1 Small-Scale Multipath Propagation 2 Impulse Response
More informationImplementation of a MIMO Transceiver Using GNU Radio
ECE 4901 Fall 2015 Implementation of a MIMO Transceiver Using GNU Radio Ethan Aebli (EE) Michael Williams (EE) Erica Wisniewski (CMPE/EE) The MITRE Corporation 202 Burlington Rd Bedford, MA 01730 Department
More informationTesting c2k Mobile Stations Using a Digitally Generated Faded Signal
Testing c2k Mobile Stations Using a Digitally Generated Faded Signal Agenda Overview of Presentation Fading Overview Mitigation Test Methods Agenda Fading Presentation Fading Overview Mitigation Test Methods
More informationSIMULATION MODELING OF STATISTICAL NAKAGAMI-m FADING CHANNELS MASTER OF ENGINEERING (M.E.) ELECTRONICS AND COMMUNICATION ENGINEERING MANNAM RAMA RAO
SIMULATION MODELING OF STATISTICAL NAKAGAMI-m FADING CHANNELS Thesis submitted in partial fulfillment of the requirement for the award of the degree of MASTER OF ENGINEERING (M.E.) In ELECTRONICS AND COMMUNICATION
More informationLecture 1 Wireless Channel Models
MIMO Communication Systems Lecture 1 Wireless Channel Models Prof. Chun-Hung Liu Dept. of Electrical and Computer Engineering National Chiao Tung University Spring 2017 2017/3/2 Lecture 1: Wireless Channel
More informationWireless Communication: Concepts, Techniques, and Models. Hongwei Zhang
Wireless Communication: Concepts, Techniques, and Models Hongwei Zhang http://www.cs.wayne.edu/~hzhang Outline Digital communication over radio channels Channel capacity MIMO: diversity and parallel channels
More informationChannel Modelling ETIM10. Propagation mechanisms
Channel Modelling ETIM10 Lecture no: 2 Propagation mechanisms Ghassan Dahman \ Fredrik Tufvesson Department of Electrical and Information Technology Lund University, Sweden 2012-01-20 Fredrik Tufvesson
More informationTEMPUS PROJECT JEP Wideband Analysis of the Propagation Channel in Mobile Broadband System
Department of Electrical Engineering and Computer Science TEMPUS PROJECT JEP 743-94 Wideband Analysis of the Propagation Channel in Mobile Broadband System Krzysztof Jacek Kurek Final report Supervisor:
More information1.1 Introduction to the book
1 Introduction 1.1 Introduction to the book Recent advances in wireless communication systems have increased the throughput over wireless channels and networks. At the same time, the reliability of wireless
More informationAntennas & Propagation. CSG 250 Fall 2007 Rajmohan Rajaraman
Antennas & Propagation CSG 250 Fall 2007 Rajmohan Rajaraman Introduction An antenna is an electrical conductor or system of conductors o Transmission - radiates electromagnetic energy into space o Reception
More informationElham Torabi Supervisor: Dr. Robert Schober
Low-Rate Ultra-Wideband Low-Power for Wireless Personal Communication Area Networks Channel Models and Signaling Schemes Department of Electrical & Computer Engineering The University of British Columbia
More informationEffects of Fading Channels on OFDM
IOSR Journal of Engineering (IOSRJEN) e-issn: 2250-3021, p-issn: 2278-8719, Volume 2, Issue 9 (September 2012), PP 116-121 Effects of Fading Channels on OFDM Ahmed Alshammari, Saleh Albdran, and Dr. Mohammad
More informationChapter 2 Channel Equalization
Chapter 2 Channel Equalization 2.1 Introduction In wireless communication systems signal experiences distortion due to fading [17]. As signal propagates, it follows multiple paths between transmitter and
More informationANALOGUE TRANSMISSION OVER FADING CHANNELS
J.P. Linnartz EECS 290i handouts Spring 1993 ANALOGUE TRANSMISSION OVER FADING CHANNELS Amplitude modulation Various methods exist to transmit a baseband message m(t) using an RF carrier signal c(t) =
More informationWritten Exam Channel Modeling for Wireless Communications - ETIN10
Written Exam Channel Modeling for Wireless Communications - ETIN10 Department of Electrical and Information Technology Lund University 2017-03-13 2.00 PM - 7.00 PM A minimum of 30 out of 60 points are
More informationUltra Wideband Radio Propagation Measurement, Characterization and Modeling
Ultra Wideband Radio Propagation Measurement, Characterization and Modeling Rachid Saadane rachid.saadane@gmail.com GSCM LRIT April 14, 2007 achid Saadane rachid.saadane@gmail.com ( GSCM Ultra Wideband
More informationRadio channel modeling: from GSM to LTE
Radio channel modeling: from GSM to LTE and beyond Alain Sibille Telecom ParisTech Comelec / RFM Outline Introduction: why do we need channel models? Basics Narrow band channels Wideband channels MIMO
More informationEITN85, FREDRIK TUFVESSON ELECTRICAL AND INFORMATION TECHNOLOGY
Wireless Communication Channels Lecture 6: Channel Models EITN85, FREDRIK TUFVESSON ELECTRICAL AND INFORMATION TECHNOLOGY Content Modelling methods Okumura-Hata path loss model COST 231 model Indoor models
More information3. Channel Propagation, Fading, and Link Budget Analysis
3. Channel Propagation, Fading, and Link Budget Analysis 3.1 Introduction 3.2 Radio Wave Propagation 3.3 Large-Scale Fading or Macroscopic Fading 3.4 Small-Scale Fading 3.5 Microscopic Fading Measurements
More informationFundamentals of Wireless Communication
Fundamentals of Wireless Communication David Tse University of California, Berkeley Pramod Viswanath University of Illinois, Urbana-Champaign Fundamentals of Wireless Communication, Tse&Viswanath 1. Introduction
More informationImpact of Mobility and Closed-Loop Power Control to Received Signal Statistics in Rayleigh Fading Channels
mpact of Mobility and Closed-Loop Power Control to Received Signal Statistics in Rayleigh Fading Channels Pekka Pirinen University of Oulu Telecommunication Laboratory and Centre for Wireless Communications
More informationAnalysis of Fast Fading in Wireless Communication Channels M.Siva Ganga Prasad 1, P.Siddaiah 1, L.Pratap Reddy 2, K.Lekha 1
International Journal of ISSN 0974-2107 Systems and Technologies IJST Vol.3, No.1, pp 139-145 KLEF 2010 Fading in Wireless Communication Channels M.Siva Ganga Prasad 1, P.Siddaiah 1, L.Pratap Reddy 2,
More informationCellular Network Planning and Optimization Part VI: WCDMA Basics. Jyri Hämäläinen, Communications and Networking Department, TKK, 24.1.
Cellular Network Planning and Optimization Part VI: WCDMA Basics Jyri Hämäläinen, Communications and Networking Department, TKK, 24.1.2008 Outline Network elements Physical layer Radio resource management
More informationPropagation Characteristics of a Mobile Radio Channel for Rural, Suburban and Urban Environments
Propagation Characteristics of a Mobile Radio Channel for Rural, Suburban and Urban Environments Mr. ANIL KUMAR KODURI, Mr. VSRK. SHARMA 2, Mr. M. KHALEEL ULLAH KHAN 3, STUDENT, M.TECH 2,3 ASSOCIATE PROFESSOR
More informationWireless Physical Layer Concepts: Part II
Wireless Physical Layer Concepts: Part II Raj Jain Professor of CSE Washington University in Saint Louis Saint Louis, MO 63130 Jain@cse.wustl.edu Audio/Video recordings of this lecture are available at:
More informationWireless Fading Channels
Wireless Fading Channels Dr. Syed Junaid Nawaz Assistant Professor Department of Electrical Engineering COMSATS Institute of Information Technology Islamabad, Paistan. Email: junaidnawaz@ieee.org Courtesy
More informationRRC Vehicular Communications Part II Radio Channel Characterisation
RRC Vehicular Communications Part II Radio Channel Characterisation Roberto Verdone Slides are provided as supporting tool, they are not a textbook! Outline 1. Fundamentals of Radio Propagation 2. Large
More information5 GHz Radio Channel Modeling for WLANs
5 GHz Radio Channel Modeling for WLANs S-72.333 Postgraduate Course in Radio Communications Jarkko Unkeri jarkko.unkeri@hut.fi 54029P 1 Outline Introduction IEEE 802.11a OFDM PHY Large-scale propagation
More informationAntennas and Propagation
Antennas and Propagation Chapter 5 Introduction An antenna is an electrical conductor or system of conductors Transmission - radiates electromagnetic energy into space Reception - collects electromagnetic
More informationLECTURE 3. Radio Propagation
LECTURE 3 Radio Propagation 2 Simplified model of a digital communication system Source Source Encoder Channel Encoder Modulator Radio Channel Destination Source Decoder Channel Decoder Demod -ulator Components
More informationOrthogonal Frequency Division Multiplexing (OFDM) based Uplink Multiple Access Method over AWGN and Fading Channels
Orthogonal Frequency Division Multiplexing (OFDM) based Uplink Multiple Access Method over AWGN and Fading Channels Prashanth G S 1 1Department of ECE, JNNCE, Shivamogga ---------------------------------------------------------------------***----------------------------------------------------------------------
More informationWireless Physical Layer Concepts: Part III
Wireless Physical Layer Concepts: Part III Raj Jain Professor of CSE Washington University in Saint Louis Saint Louis, MO 63130 Jain@cse.wustl.edu These slides are available on-line at: http://www.cse.wustl.edu/~jain/cse574-08/
More informationReflection. Diffraction. Transmission. Scattering
WIRELESS TRANSMISSION 649 Reflection Diffraction Transmission Scattering Figure 13.5 Mechanisms of radio propagation. elements follows some geometric pattern (example, linearly spaced elements, elements
More informationEC 551 Telecommunication System Engineering. Mohamed Khedr
EC 551 Telecommunication System Engineering Mohamed Khedr http://webmail.aast.edu/~khedr 1 Mohamed Khedr., 2008 Syllabus Tentatively Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week
More informationSpread Spectrum Techniques
0 Spread Spectrum Techniques Contents 1 1. Overview 2. Pseudonoise Sequences 3. Direct Sequence Spread Spectrum Systems 4. Frequency Hopping Systems 5. Synchronization 6. Applications 2 1. Overview Basic
More informationKing Fahd University of Petroleum & Minerals Computer Engineering Dept
King Fahd University of Petroleum & Minerals Computer Engineering Dept COE 543 Mobile and Wireless Networks Term 0 Dr. Ashraf S. Hasan Mahmoud Rm -148-3 Ext. 174 Email: ashraf@ccse.kfupm.edu.sa 4//003
More informationInternational Journal of Advance Engineering and Research Development. Performance Comparison of Rayleigh and Rician Fading Channel Models: A Review
Scientific Journal of Impact Factor (SJIF): 5.71 International Journal of Advance Engineering and Research Development Volume 5, Issue 02, February -2018 e-issn (O): 2348-4470 p-issn (P): 2348-6406 Performance
More informationChannel Modelling for Beamforming in Cellular Systems
Channel Modelling for Beamforming in Cellular Systems Salman Durrani Department of Engineering, The Australian National University, Canberra. Email: salman.durrani@anu.edu.au DERF June 26 Outline Introduction
More informationAntennas and Propagation. Chapter 5
Antennas and Propagation Chapter 5 Introduction An antenna is an electrical conductor or system of conductors Transmission - radiates electromagnetic energy into space Reception - collects electromagnetic
More informationMEASUREMENT AND MODELING OF INDOOR UWB CHANNEL AT 5 GHz
MEASUREMENT AND MODELING OF INDOOR UWB CHANNEL AT 5 GHz WINLAB @ Rutgers University July 31, 2002 Saeed S. Ghassemzadeh saeedg@research.att.com Florham Park, New Jersey This work is based on collaborations
More informationEffects of multipath propagation on design and operation of line-of-sight digital radio-relay systems
Rec. ITU-R F.1093-1 1 RECOMMENDATION ITU-R F.1093-1* Rec. ITU-R F.1093-1 EFFECTS OF MULTIPATH PROPAGATION ON THE DESIGN AND OPERATION OF LINE-OF-SIGHT DIGITAL RADIO-RELAY SYSTEMS (Question ITU-R 122/9)
More informationExam 3 is two weeks from today. Today s is the final lecture that will be included on the exam.
ECE 5325/6325: Wireless Communication Systems Lecture Notes, Spring 2010 Lecture 19 Today: (1) Diversity Exam 3 is two weeks from today. Today s is the final lecture that will be included on the exam.
More informationPROPAGATION MODELING 4C4
PROPAGATION MODELING ledoyle@tcd.ie 4C4 http://ledoyle.wordpress.com/temp/ Classification Band Initials Frequency Range Characteristics Extremely low ELF < 300 Hz Infra low ILF 300 Hz - 3 khz Ground wave
More informationS Postgraduate Course in Radiocommunications. WCDMA Radio Link Performance Indicators. Seminar Mervi Berner
S-72.333 Postgraduate Course in Radiocommunications Seminar 21.01.2003 Mervi Berner Content Definitions of WCDMA Radio Link Performance Indicators Multipath Channel Conditions and Services Link-level Simulation
More informationMultipath Propagation Model for High Altitude Platform (HAP) Based on Circular Straight Cone Geometry
Multipath Propagation Model for High Altitude Platform (HAP) Based on Circular Straight Cone Geometry J. L. Cuevas-Ruíz ITESM-CEM México D.F., México jose.cuevas@itesm.mx A. Aragón-Zavala ITESM-Qro Querétaro
More informationThe prediction of the time and the spatial profile for broadband land mobile services using UHF and SHF bands
Recommendation ITU-R P.1816-3 (7/15) The prediction of the time and the spatial profile for broadband land mobile services using UHF and SHF bands P Series Radiowave propagation ii Rec. ITU-R P.1816-3
More informationChannel models and antennas
RADIO SYSTEMS ETIN15 Lecture no: 4 Channel models and antennas Ove Edfors, Department of Electrical and Information Technology Ove.Edfors@eit.lth.se 2012-03-21 Ove Edfors - ETIN15 1 Contents Why do we
More informationMSIT 413: Wireless Technologies Week 3
MSIT 413: Wireless Technologies Week 3 Michael L. Honig Department of EECS Northwestern University October 2017 Why Study Radio Propagation? To determine coverage Can we use the same channels? Must determine
More informationAntennas and Propagation
Mobile Networks Module D-1 Antennas and Propagation 1. Introduction 2. Propagation modes 3. Line-of-sight transmission 4. Fading Slides adapted from Stallings, Wireless Communications & Networks, Second
More informationDiversity. Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1
Diversity Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1 Diversity A fading channel with an average SNR has worse BER performance as compared to that of an AWGN channel with the same SNR!.
More information