TL084. General purpose JFET quad operational amplifier. Features. Description
|
|
- Toby Peters
- 6 years ago
- Views:
Transcription
1 General purpose JFET quad operational amplifier Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Output shortcircuit protection High input impedance JFET input stage Internal frequency compensation Latch up free operation High slew rate: 16V/µs (typ) Description The, A and B are highspeed JFET input quad operational amplifiers incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. N DIP14 (Plastic package) D TSSOP14 (Thin shrink small outline package) D SO14 (Plastic micropackage) Pin connections (Top view) Output Output 4 Inverting Input 1 2 Noninverting Input Inverting Input 4 Noninverting Input 4 V CC VCC Noninverting Input 2 Inverting Input Noninverting Input 3 Inverting Input 3 Output Output 3 July 2007 Rev 2 1/
2 Schematic diagram 1 Schematic diagram Figure 1. Circuit schematics (for each amplifier) V CC Noninverting input Inverting input 0Ω 200Ω Output 30k 0Ω 8.2k 1.3k 35k 1.3k 35k 0Ω V CC 2/16
3 Absolute maximum ratings and operating conditions 2 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol Parameter Value M, AM, BM I, AI, BI C, AC, BC Unit V CC Supply voltage (1) ±18 V V i Input voltage (2) ±15 V V id Differential input voltage (3) ±30 V R thja R thjc Thermal resistance junction to (4) (5) ambient SO14 DIP14 TSSOP14 Thermal resistance junction to case (4) (5) SO14 DIP14 TSSOP14 P tot Power dissipation 680 mw Output shortcircuit duration (6) Infinite T oper Operating freeair temperature range 55 to to +5 0 to +70 C T stg Storage temperature range 65 to +150 C ESD HBM: human body model (7) MM: machine model (8) 150 CDM: charged device model (9) All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages + where the zero reference level is the midpoint between V CC and V CC. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the noninverting input terminal with respect to the inverting input terminal. 4. Shortcircuits can cause excessive heating and destructive dissipation. 5. Rth are typical values. 6. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 7. Human body model: 0pF discharged through a 1.5kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Table 2. Operating conditions Symbol Parameter M, AM, BM I, AI, BI C, AC, BC Unit V CC Supply voltage range 6 to 36 V T oper Operating freeair temperature range 55 to to +5 0 to +70 C C/W C/W V 3/16
4 Electrical characteristics 3 Electrical characteristics Table 3. Symbol V CC = ±15V, T amb = +25 C (unless otherwise specified) Parameter I,M,AC,AI,AM, BC,BI,BM C Min. Typ. Max. Min. Typ. Max. Unit V io Input offset voltage (R s = 50Ω) T amb = +25 C A B T min T amb T max A B DV io Input offset voltage drift μv/ C I io Input offset current T amb = +25 C 5 0 T min T amb T max 4 Input bias current (1) I ib T amb = +25 C T min T amb T max 20 A vd SVR I CC V icm CMR I os ±V opp SR Large signal voltage gain (R L = 2kΩ, V o =±V) T amb = +25 C 50 T min T amb T max 25 Supply voltage rejection ratio (R S = 50Ω) T amb = +25 C 80 T min T amb T max Supply current, no load T amb = +25 C T min T amb T max 2.5 Input common mode voltage range Common mode rejection ratio (R S = 50Ω) T amb = +25 C 80 T min T amb T max 80 Output shortcircuit current T amb = +25 C T min T amb T max Output voltage swing T amb = +25 C T min T amb T max RL = 2kΩ RL = kω RL = 2kΩ RL = kω Slew rate (T amb = +25 C) V in = V, R L = 2kΩ, C L = 0pF, unity gain ± ± mv pa na pa na 200 V/mV 86 db ma V 86 db ma V V/μs 4/16
5 Electrical characteristics Table 3. Symbol V CC = ±15V, T amb = +25 C (unless otherwise specified) (continued) Parameter I,M,AC,AI,AM, BC,BI,BM C Min. Typ. Max. Min. Typ. Max. Unit t r K ov Rise time (T amb = +25 C) V in = 20mV, R L = 2kΩ, C L = 0pF, unity gain Overshoot (T amb = +25 C) V in = 20mV, R L = 2kΩ, C L = 0pF, unity gain μs % GBP Gain bandwidth product (T amb = +25 C) V in = mv, R L = 2kΩ, C L = 0pF, f= 0kHz MHz R i Input resistance Ω THD Total harmonic distortion (T amb = +25 C, f= 1kHz, R L = 2kΩ,C L = 0pF, A v = 20dB, V o = 2V pp ) % Equivalent input noise voltage nv e n R S = 0Ω, f = 1KHz Hz m Phase margin degrees V o1 /V o2 Channel separation A v = db 1. The input bias currents are junction leakage currents which approximately double for every C increase in the junction temperature. 5/16
6 Electrical characteristics Figure 2. Maximum peaktopeak output voltage versus frequency Figure 3. Maximum peaktopeak output voltage versus frequency Figure 4. Maximum peaktopeak output voltage versus frequency Figure 5. Maximum peaktopeak output voltage versus free air temperature Figure 6. Maximum peaktopeak output voltage versus load resistance Figure 7. Maximum peaktopeak output voltage versus supply voltage MAXIMUM PEAKTOPEAK OUTPUT VOLTAGE (V) R L = kω T amb = +25 C SUPPLY VOLTAGE ( V) 6/16
7 Electrical characteristics Figure 8. Input bias current versus free air temperature Figure 9. Large signal differential voltage amplification versus free air temperature INPUT BIAS CURRENT (na) 0 V CC = 15V DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) V CC = 15V V 4 O = V 2 R = 2k Ω L TEMPERATURE ( C) TEMPERATURE ( C) Figure. Large signal differential voltage amplification and phase shift versus frequency Figure 11. Total power dissipation versus free air temperature TOTAL POWER DISSIPATION (mw) V CC = 15V No signal No load TEMPERATURE ( C) Figure 12. Supply current per amplifier versus free air temperature Figure 13. Supply current per amplifier versus supply voltage SUPPLY CURRENT (ma) TEMPERATURE ( C) V CC = 15V No signal No load SUPPLY CURRENT (ma) T amb = +25 C No signal No load SUPPLY VOLTAGE ( V) 7/16
8 Electrical characteristics Figure 14. Common mode rejection ratio versus free air temperature Figure 15. Voltage follower large signal pulse response COMMON MODE MODE REJECTION RATIO (db) R L = kω V CC = 15V TEMPERATURE ( C) Figure 16. Output voltage versus elapsed time Figure 17. Equivalent input noise voltage versus frequency OUTPUT VOLTAGE (mv) OVERSHOOT 90% V CC = 15V R % L = 2k Ω T t amb = +25 C r TIME ( μs) EQUIVALENT INPUT NOISE VOLTAGE (nv/vhz) V CC = 15V A V = R S = 0 Ω T amb = +25 C k 4k k 40k 0k FREQUENCY (Hz) Figure 18. Total harmonic distortion versus frequency TOTAL HARMONIC DISTORTION (%) 1 V V CC 0.4 CC = = 15V 15V A AV V = = 1 1 V V 0.1 O O (rms) (rms) = = 6V 6V T amb T 0.04 amb = = +25 C k 4k k 40k 0k FREQUENCY (Hz) 8/16
9 Typical applications Parameter measurement information Figure 19. Voltage follower Figure 20. Gainof inverting amplifier k Ω e I 1k Ω e o R L C L = 0pF 4 Typical applications Figure 21. Audio distribution amplifier f O = 0kHz 1M Ω Output A Input 1μF Output B 0k Ω 1OO μf 0k Ω 0k Ω 0k Ω V CC + Output C 9/16
10 Typical applications Figure 22. Positive feeback bandpass filter 16k Ω 16k Ω 220pF 220pF 43k Ω 43k Ω Input 43k Ω 1.5k Ω 220pF 43k Ω 30k Ω 43k Ω 1.5k Ω 220pF 43k Ω 30k Ω Output B Output A Ground Figure 23. Output A Figure 24. Output B Second order bandpass filter fo = 0kHz; Q = 30; Gain = 4 Cascaded bandpass filter fo = 0kHz; Q = 69; Gain = 16 /16
11 Package information 5 Package information In order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a leadfree second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: Figure 25. Ref. TSSOP14 package mechanical data Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. A A A b c D E E e 0.65 BSC BSC K L A A2 A1 b e c K L E D E1 PIN 1 IDENTIFICATION 1 11/16
12 Package information Figure 26. Ref. DIP14 package mechanical data Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. a B b b D E e e F I L Z /16
13 Package information Figure 27. Ref. SO14 package mechanical data Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. A a a b b C c1 45 (typ.) D E e e F G L M S 8 (max.) 13/16
14 Ordering information 6 Ordering information Table 4. Part number Order codes Temperature range Package Packing Marking MN AMN BMN DIP14 Tube MN AMN BMN MD/MDT AMD/AMDT BMD/BMDT 55 C, +125 C SO14 Tube or tape & reel 084M 084AM 084BM MP/MPT AMP/AMPT BMP/BMPT TSSOP14 Tube or tape & reel 084M 084AM 084BM IN AIN BIN DIP14 Tube IN AIN BIN ID/IDT AID/AIDT BID/BIDT 40 C, +5 C SO14 Tube or tape & reel 084I 084AI 084BI IP/IPT AIP/AIPT BIP/BIPT TSSOP14 Tube or tape & reel 084I 084AI 084BI CN ACN BCN DIP14 Tube CN ACN BCN CD/CDT ACD/ACDT BCD/BCDT 0 C, +70 C SO14 Tube or tape & reel 084C 084AC 084BC CP/CPT ACP/ACPT BCP/BCPT TSSOP14 Tube or tape & reel 084C 084AC 084BC 14/16
15 Revision history 7 Revision history Table 5. Document revision history Date Revision Changes 28Mar Initial release. 30Jul Added values for R thja, R thjc and ESD in Table 1: Absolute maximum ratings. Added Table 2: Operating conditions. Expanded Table 4: Order codes. Template update. 15/16
16 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics All rights reserved STMicroelectronics group of companies Australia Belgium Brazil Canada China Czech Republic Finland France Germany Hong Kong India Israel Italy Japan Malaysia Malta Morocco Singapore Spain Sweden Switzerland United Kingdom United States of America 16/16
TL064. Low power JFET quad operational amplifier. Features. Description
Low power JFET quad operational amplifier Features Very low power consumption: 0 µa Wide commonmode (up to V + CC ) and differential voltage ranges Low input bias and offset currents Output shortcircuit
More informationTL062. Low power JFET dual operational amplifiers. Features. Description + -
Low power JFET dual operational amplifiers Features Very low power consumption : 0µA Wide common-mode (up to V + CC ) and differential voltage ranges Low input bias and offset currents Output short-circuit
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
Low noise JFET quad operational amplifier Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ) Output shortcircuit protection
More informationLF253 LF353. Wide bandwidth dual JFET operational amplifiers. Features. Description
Wide bandwidth dual JFET operational amplifiers Features Low power consumption Wide common-mode (up to V CC + ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationLF253, LF353. Wide bandwidth dual JFET operational amplifiers. Features. Description
Wide bandwidth dual JFET operational amplifiers Features Low power consumption Wide common-mode (up to + ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
Low noise JFET quad operational amplifier Datasheet production data Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ)
More informationTL084. General purpose JFET quad operational amplifiers. Features. Description
General purpose JFET quad operational amplifiers Datasheet production data Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Output shortcircuit
More informationMC Low noise quad operational amplifier. Features. Description
MC3379 Low noise quad operational amplifier Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion:.2% Large output voltage swing: +14.3 V/-14.6
More informationTL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
More informationMC33172 MC Low power dual bipolar operational amplifiers. Features. Description
Low power dual bipolar operational amplifiers Features Good consumption/speed ratio: only 200 µa for 2.1MHz, 2V/µs Single (or dual) supply operation from +4 V to +44V (±2V to ±22V) Wide input common mode
More informationTL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC
I, AI, BI, C, AC, BC General purpose JFET quad operational amplifiers Datasheet production data Features Wide commonmode (up to V CC + ) and differential voltage range Low input bias and offset current
More informationTS522. Precision low noise dual operational amplifier. Features. Description
Precision low noise dual operational amplifier Datasheet production data Features Large output voltage swing: +14.3 V/-14.6 V Low input offset voltage 850 μv max. Low voltage noise: 4.5 nv/ Hz High gain
More informationTL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
More informationNon-inverting input 1. Part Number Temperature Range Package Packing Marking. 4558C MC4558CPT TSSOP8 Tape & Reel MC4558IN
Wide Bandwidth Dual Bipolar Operational Amplifier Internally compensated Short-circuit protection Gain and phase match between amplifier Low power consumption Pin-to-pin compatible with MC1458/LM358 Gain
More informationTS27L4. Very low power precision CMOS quad operational amplifiers. Features. Description
Very low power precision CMOS quad operational amplifiers Features Very low power consumption: µa/op Output voltage can swing to ground Excellent phase margin on capacitive loads Unity gain stable Two
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationLM248, LM348. Four UA741 quad bipolar operational amplifiers. Description. Features
Four UA741 quad bipolar operational amplifiers Description Datasheet - production data Features D SO14 Pin connections (top view) Low supply current: 0.53 ma per amplifier Class AB output stage: no crossover
More informationTL082 TL082A - TL082B
TL082 TL082A - TL082B GENERAL PURPOSE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationObsolete Product(s) - Obsolete Product(s)
Low power quad operational amplifier Features Wide gain bandwidth: 1.3 MHz Extended temperature range: -40 C to +150 C Input common-mode voltage range includes negative rail Large voltage gain: 100 db
More informationTL071 TL071A - TL071B
TL7 TL7A TL7B LOW NOISE JFET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 5nV/ Hz (typ) OUTPUT SHORTCIRCUIT
More informationOrder code Temperature range Package Packaging Marking
Micropower quad CMOS voltage comparator Datasheet production data Features Extremely low supply current: 9 μa typ./comp. Wide single supply range 2.7 V to 16 V or dual supplies (±1.35 V to ±8 V) Extremely
More informationTL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationTL064 TL064A - TL064B
TL6 TL6A TL6B LOW POWER JFET QUAD OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
More informationTS3704. Micropower quad CMOS voltage comparators. Features. Description
Micropower quad CMOS voltage comparators Features Push-pull CMOS output (no external pull-up resistor required) Extremely low supply current: 9μa typ per comparator Wide single supply range 2.7V to 6V
More informationTL062 TL062A - TL062B
TL62 TL62A TL62B LOW POWER JFET DUAL OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO + ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
More informationTL084, TL084A, TL084B
General purpose JFET quad operational amplifiers Datasheet production data Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Output shortcircuit
More informationTL072 TL072A - TL072B
TL072 TL072A - TL072B Low noise J-FET dual operational amplifiers Features Wide common-mode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15nV/ Hz (typ)
More informationLM2901. Low power quad voltage comparator. Features. Description
Low power quad voltage comparator Features Wide single supply voltage range or dual supplies for all devices: +2 V to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of supply voltage
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
TL074 Low noise JFET quad operational amplifier Features Wide commonmode (up to V CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ) Output shortcircuit
More informationLM2903W. Low-power, dual-voltage comparator. Features. Description
Low-power, dual-voltage comparator Datasheet production data Features Wide, single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply
More informationLMV321-LMV358-LMV324. Low cost low power input/output rail-to-rail operational amplifiers. Features. Applications. Description LMV321ILT (SOT23-5)
Low cost low power input/output rail-to-rail operational amplifiers Features Operating range from V CC = 2.7V to 6V Rail-to-rail input and output Extended V icm (V DD -.2V to V CC +.2V) Low supply current
More informationLM2902. Low power quad operational amplifier. Features. Description
Low power quad operational amplifier Features Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes negative rail Large voltage gain: 100dB Very low supply current per amp: 375µA Low input
More informationTL072 TL072A - TL072B
A - B LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORT-CIRCUIT PROTECTION
More informationTL081 TL081A - TL081B
TL8 TL8A - TL8B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION HIGH
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. -LM258-LM358 A-LM258A-LM358A Low power dual operational amplifiers Features
More informationPart Number Temperature Range Package Packing Marking. DIP14 Tube LM2902N LM2902D/DT SO-14 Tube or Tape & Reel
Low Power Quad Operational Amplifier Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes ground Large voltage gain: 1dB Very low supply current per amp: 375µA Low input bias current: 2nA
More informationLM224A, LM324A. Low-power quad operational amplifiers. Features. Description
Low-power quad operational amplifiers Features Datasheet - production data D SO14 (plastic micropackage) Wide gain bandwidth: 1.3 MHz Input common mode voltage range includes ground Large voltage gain:
More informationTSL channel buffers for TFT-LCD panels. Features. Application. Description
14 + 1 channel buffers for TFT-LCD panels Datasheet production data Features Wide supply voltage: 5.5 V to 16.8 V Low operating current: 6 ma typical at 25 C Gain bandwidth product: 1 MHz High current
More informationTL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
More informationLM723CN. High precision voltage regulator. Features. Description
High precision voltage regulator Features Input voltage up to 40 V Output voltage adjustable from 2 to 37 V Positive or negative supply operation Series, shunt, switching or floating operation Output current
More informationLM2903H. Low-power dual voltage comparator. Features. Description
LM23H Low-power dual voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent
More informationLM139, LM239, LM339. Low-power quad voltage comparators. Features. Description
, LM239, LM339 Low-power quad voltage comparators Features Wide single supply voltage range or dual supplies for all devices: +2 to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of
More informationFeatures. Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
Micropower quad CMOS voltage comparator Features Datasheet - production data D SO14 (plastic micropackage) P TSSOP14 (thin shrink small outline package) Pin connections top view Extremely low supply current:
More informationTS391. Low-power single voltage comparator. Features. Description
Low-power single voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.2 ma) independent of supply
More informationTS982. Wide bandwidth dual bipolar operational amplifier. Features. Applications. Description
Wide bandwidth dual bipolar operational amplifier Features Operating from V CC = 2.5 V to 5.5 V 0 ma output current on each amplifier High dissipation package Rail-to-rail input and output Unity gain stable
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationTL082 TL082A - TL082B
TL082 TL082A - TL082B General purpose J-FET dual operational amplifiers Features Wide common-mode (up to V + CC ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationLM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
More information. WIDE COMMON-MODE (UP TO VCC + ) AND
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS. WIDE COMMONMODE (UP TO VCC + ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT. LOW NOISE e n = nv/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
More informationTL072, TL072A, TL072B
Low noise JFET dual operational amplifiers Datasheet production data Features Wide common-mode (up to V CC + ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz
More informationObsolete Product(s) - Obsolete Product(s)
2 W mono amplifier Features 2 W output power into 8 Ω at 12 V, THD = 10% Internally fixed gain of 32 db No feedback capacitor No boucherot cell Thermal protection AC short-circuit protection SVR capacitor
More informationTSH110-TSH111-TSH112-TSH113-TSH114
Wide band low noise operational amplifiers Features Low noise: 3nV/ Hz Low supply current: 3.2mA 47mA output current Bandwidth: 100MHz 5V to 12V supply voltage Slew rate: 450V/μs Specified for 100Ω load
More informationTS27M2, TS27M2A, TS27M2B
Low-power CMOS dual operational amplifiers Features Wide supply voltage range: 3 to 6 V Ultra-low consumption: 50 µa/op typ Output voltage swing to ground Excellent phase margin on capacitive load Gain
More informationLM193, LM193A, LM293, LM293A, LM393, LM393A
, A, LM293, LM293A, LM393, LM393A Low Power Dual oltage Comparators Wide single-supply voltage range or dual supplies: +2 to +36 or ± to ±8 ery low supply current (.4mA) independent of supply voltage (mw/comparator
More informationTL084 TL084A - TL084B
TL84 TL84A TL84B GENERAL PURPOSEJFET QUAD OPERATIONAL AMPLIFIERS. WIDE COMMONMODE (UP TO VCC + ) AND DIFFERENTIAL VOLTAGE RANGE. LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT
More informationLM323. Three-terminal 3 A adjustable voltage regulators. Features. Description
Three-terminal 3 A adjustable voltage regulators Features Output current: 3 A Internal current and thermal limiting Typical output impedance: 0.01 W Minimum input voltage: 7.5 V Power dissipation: 30 W
More informationLMV321, LMV358, LMV324
Low cost, low power, input/output rail-to-rail operational amplifiers Features Operating range from V CC = 2.7 V to 6 V Rail-to-rail input and output Extended V icm (V DD -.2 V to V CC +.2 V) Low supply
More informationTSC1021. High-side current sense amplifier. Features. Description. Applications
High-side current sense amplifier Features Wide common-mode operating range independent of supply: 2.8 to 30 V Wide common-mode surviving range: -32 to 60 V (reversed battery and load-dump conditions)
More informationTS27M4C, TS27M4I, TS27M4M
Precision low power CMOS quad operational amplifiers Features Low power consumption: 50 µa/op Output voltage can swing to ground Excellent phase margin on capacitive loads Unity gain stable Two input offset
More informationL4940xx5 L4940V5 L4940D2T5-TR 5 V L4940xx85 L4940V85 L4940P85 L4940D2T85-TR 8.5 V L4940xx10 L4940D2T10-TR 10 V L4940xx12 L4940D2T12-TR 12 V
Very low drop 1.5 A regulator Features Precise 5, 8.5, 10, 12 V outputs Low dropout voltage (450 mv typ. at 1 A) Very low quiescent current Thermal shutdown Short circuit protection Reverse polarity protection
More informationLow noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
More informationMC33001/A/B MC34001/A/B MC35001/A/B GENERAL PURPOSE SINGLE JFET OPERATIONAL AMPLIFIERS.
MC33/A/B MC3/A/B MC3/A/B GENERAL PURPOSE SINGLE JFET OPERATIONAL AMPLIFIERS. LOW POWER CONSUMPTION WIDE COMMONMODE (UP TO VCC + ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT. OUTPUT
More informationTS V micropower shunt voltage reference. Features. Applications. Description
2. micropower shunt voltage reference Features 2.5 typical output voltage Ultra low current consumption: 4µA typ. High precision @ 25 C ±2% (standard version) ±1% (A grade) High stability when used with
More information. WIDE COMMON-MODE (UP TO VCC + ) AND
TL7 TL7A TL7B LOW NOISE JFET SINGLE OPERATIONAL AMPLIFIERS. WIDE COMMONMODE (UP TO VCC + ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT. LOW NOISE e n = nv/ Hz (typ) OUTPUT SHORTCIRCUIT
More informationObsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s)
5 A low dropout fast response positive voltage regulator adjustable Features Typical dropout 1.2 V Fast transient response Three terminal adjustable Guaranteed output current up to 5 A Output tolerance
More informationBD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
More information2STC4468. High power NPN epitaxial planar bipolar transistor. Features. Application. Description
High power NPN epitaxial planar bipolar transistor Features High breakdown voltage V CEO = 140 V Complementary to 2STA1695 Typical f t = 20 MHz Fully characterized at 125 o C Application Audio power amplifier
More informationHCF4093. QUAD 2-input NAND Schmidt trigger. Features. Description
QUAD 2-input NAND Schmidt trigger Features Schmidt trigger action on each input with no external components Hysteresis voltage typically 0.9 V at V DD =5V and 2.3 V at V DD =10 V Noise immunity greater
More informationTEB1033 TEF1033-TEC1033
TEB1033 TEF1033-TEC1033 PRECISION DUAL OPERATIONAL AMPLIFIERS VERY LOW INPUT OFFSET VOLTAGE : 1mV max. LOW DISTORTION RATIO LOW NOISE VERY LOW SUPPLY CURRENT LOW INPUT OFFSET CURRENT LARGE COMMON-MODE
More informationLD1085CXX. 3 A low-drop, adjustable positive voltage regulator. Features. Description
3 A low-drop, adjustable positive voltage regulator Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable output voltage Guaranteed output current up to 3 A Output tolerance ± 2 % at 25 C and
More information2STN2540. Low voltage fast-switching PNP power bipolar transistor. Features. Applications. Description
2STN2540 Low voltage fast-switching PNP power bipolar transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface mounting device in
More informationLF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS
LF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationObsolete Product(s) - Obsolete Product(s)
High gain Low Voltage PNP power transistor Features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current Applications Power management in portable
More informationObsolete Product(s) - Obsolete Product(s)
Three-terminal 5 A adjustable voltage regulators Features Guaranteed 7 A peak output current Guaranteed 5 A output current Adjustable output down to 1.2 V Line regulation typically 0.005 %/V Load regulation
More information2STA1943. High power PNP epitaxial planar bipolar transistor. Features. Application. Description
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO > -230V Complementary to 2STC5200 Fast-switching speed Typical f T = 30 MHz Application Audio power amplifier Description
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER. INTERNALLY ADJUSTABLE INPUT OFFSET.
LF LF LF3 WIDE BANDWIDTH SINGLE JFET OPERATIONAL AMPLIFIER. INTERNALLY ADJUSTABLE INPUT OFFSET. VOLTAGE LOW POWER CONSUMPTION WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE. LOW INPUT BIAS
More informationUA741 GENERAL PURPOSE SINGLE OPERATIONAL AMPLIFIER
GENERAL PURPOSE SINGLE OPERATIONAL AMPLIFIER LARGE INPUT VOLTAGE RANGE NO LATCH-UP HIGH GAIN SHORT-CIRCUIT PROTECTION NO FREQUENCY COMPENSATION REQUIRED SAME PIN CONFIGURATION AS THE UA709 N DIP8 (Plastic
More informationSTD1802T4-A. Low voltage fast-switching NPN power transistor. Features. Description. Applications
Low voltage fast-switching NPN power transistor Features This device is qualified for automotive application Very low collector to emitter saturation voltage High current gain characteristic Fast-switching
More informationTSV321-TSV358-TSV324. General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers. Description. Applications
General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers Operating at V CC = 2.5V to 6V Rail-to-rail input & output Extended V icm (V DD -.2V to V CC +.2V) Capable of driving a 32Ω load
More informationL78S00 series. 2A Positive voltage regulators. Feature summary. Description. Schematic diagram
2A Positive voltage regulators Feature summary Output current to 2A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24V Thermal overload protection Short circuit protection Output transition SOA protection
More information. WIDE COMMON-MODE (UP TO VCC + ) AND
TL72 TL72A TL72B LOW NOISE JFET DUAL OPERATIONAL AMPLIFIERS. WIDE COMMONMODE (UP TO VCC + ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT. LOW NOISE e n = nv/ Hz (typ) OUTPUT SHORTCIRCUIT
More informationLM193, LM293, LM393. Low power dual voltage comparators. Features. Description
, LM293, LM393 Low power dual voltage comparators Features Wide single-supply voltage range or dual supplies: +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply voltage
More informationRT2904WH. RobuST low-power dual operational amplifier. Applications. Features. Description
RobuST low-power dual operational amplifier Datasheet - production data Features D SO8 (plastic micropackage) Pin connections (top view) Frequency compensation implemented internally Large DC voltage gain:
More informationMJE182 Low voltage high speed switching NPN transistor Features Applications Description High speed switching NPN device
Low voltage high speed switching NPN transistor Features High speed switching NPN device Applications Audio amplifier High speed switching applications Description This device is an NPN low voltage transistor
More informationObsolete Product(s) - Obsolete Product(s)
PNP power Darlington transistor Features Monolithic Darlington configuration Integrated antiparallel collector-emitter diode Application Linear and switching industrial equipment Description The TIP145
More informationTS881. Rail-to-rail 0.9 V nanopower comparator. Description. Features. Applications
Rail-to-rail 0.9 V nanopower comparator Description Datasheet - production data SC70-5 (top view) SOT23-5 (top view) The TS881 device is a single comparator featuring ultra low supply current (210 na typical
More informationTL1431. Programmable voltage reference. Features. Description
Programmable voltage reference Features Adjustable output voltage: V REF to 36 V Sink current capability: 1 to 100 ma Typical output impedance: 0.22 Ω 0.4% and 0.25% voltage precision Description The TL1431
More information2STC5242. High power NPN epitaxial planar bipolar transistor. Features. Application. Description
2STC5242 High power NPN epitaxial planar bipolar transistor Features High breakdown voltage V CEO = 230 V Complementary to 2STA1962 Fast-switching speed Typical f T = 30 MHz Application Audio power amplifier
More informationUA748 PRECISION SINGLE OPERATIONAL AMPLIFIER
PRECISION SINGLE OPERATIONAL AMPLIFIER INPUT OFFSET VOLTAGE : 3mV max. OVER TEMPERATURE FREQUENCY COMPENSATION WITH A SINGLE 30pF CAPACITOR (C1) OPERATION FROM ±5V to ±15V LOW POWER CONSUMPTION : 50mW
More information1.8 V input/output, rail-to-rail, low power operational amplifiers. Reference. TS185x TS1851 TS1852 TS1854. TS185xA TS1851A TS1852A TS1854A
1.8 V input/output, rail-to-rail, low power operational amplifiers Features Operating range from V CC = 1.8 to 6 V Rail-to-rail input and output Extended V icm (V CC- -.2 V to V CC + +.2 V) Low supply
More informationObsolete Product(s) - Obsolete Product(s)
High Gain Low Voltage PNP Power Transistor General features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current In compliance with the 2002/93/EC
More information2STX2220. High Gain Low Voltage PNP Power Transistor. General features. Description. Internal schematic diagram. Applications.
High Gain Low Voltage PNP Power Transistor General features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current In compliance with the 2002/93/EC
More informationPart numbers Order codes Packages Temperature range. LM137 LM137K TO-3-55 C to 150 C LM337 LM337K TO-3 0 C to 125 C LM337 LM337SP TO C to 125 C
LM137 LM337 Three-terminal adjustable negative voltage regulators Features Output voltage adjustable down to V REF 1.5 A guaranteed output current 0.3%/V typical load regulation 0.01%/V typical line regulation
More informationNE555 SA555 - SE555 General-purpose single bipolar timers Features Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
More informationObsolete Product(s) - Obsolete Product(s)
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO = -250 V Complementary to 2STC5949 Typical f t = 25 MHz Fully characterized at 125 o C Application Audio power amplifier
More informationOrder codes Marking Package Packaging 2STF SOT-89 2STN2550 N2550 SOT-223. November 2008 Rev 1 1/8
2STF2550 2STN2550 Low voltage high performance PNP power transistors Preliminary Data Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface
More informationBD533 BD535 BD537 BD534 BD536
BD533 BD535 BD537 BD534 BD536 Complementary power transistors Features. BD533, BD535, and BD537 are NPN transistors Description The devices are manufactured in Planar technology with Base Island layout.
More informationTSH103. Low cost triple video buffer/filter for standard video. Features. Applications. Description
Low cost triple video buffer/filter for standard video Features Triple channels Internal 6 MHz reconstruction filter (4 th order) 6 db gain buffer for lines 5 V single supply Bottom of video signal close
More informationDIP14 Tube LM2901N LM2901D/LM2901DT SO-14 Tube or Tape & Reel
LM2901 Low Power Quad Voltage Comparator Wide single supply voltage range or dual supplies for all devices: +2V to +36V or ±1V to ±18V Very low supply current (1.1mA) independent of supply voltage (1.4mW/comparator
More information