STP16CL596 LOW VOLTAGE 16-BIT CONSTANT CURRENT LED SINK DRIVER
|
|
|
- Jonah Barber
- 6 years ago
- Views:
Transcription
1 LOW VOLTAGE 16-BIT CONSTANT CURRENT LED SINK DRIVER LOW VOLTAGE POWER SUPPLY DOWN TO 3V 16 CONSTANT CURRENT OUTPUT CHANNELS ADJUSTABLE OUTPUT CURRENT THROUGH EXTERNAL RESISTOR SERIAL DATA IN/PARALLEL DATA OUT SERIAL OUT CHANGES STATE ON THE FALLING EDGES OF CLOCK 3.3V MICRO DRIVER-ABLE OUTPUT CURRENT: ma 25 MHz CLOCK FREQ. AVAILABLE IN HIGH THERMAL EFFICIENCY TSSOP EXPOSED PAD DIP-24 TSSOP24 SO-24 TSSOP24 (exposed pad) DESCRIPTION The STP16CL596 is a monolithic, low voltage, low current power 16-bit shift register designed for LED panel displays. The STP16CL596 contains a 16-bit serial-in, parallel-out shift register that feeds a 16-bitD-type storage register. In the output stage, sixteen regulated current sources were designed to provide 15-90mA constant current to drive the LEDs. Compared with the STPIC6C595, the device provides great flexibility and improved performance in LED panel system design. Trough an external resistor, users can adjust the STP16CL596 output current, controlling in this way the light intensity of LEDs. The STP16CL596 guarantees a 16V output driving capability, allowing users to connect more LEDs in series. The high clock frequency, 25 MHz, also satisfies the system requirement of high volume data transmission. The 3.3V of voltage supply is well useful for applications that interface any micro from 3.3V. Compared with a standard TSSOP package, the TSSOP exposed pad increases heat dissipation capability by a 2.5 factor. Table 1: Order Codes Part Number Package Comments STP16CL596B1R DIP parts per tube STP16CL596M SO-24 (Tube) 40 parts per tube STP16CL596MTR SO-24 (Tape & Reel) 1000 parts per reel STP16CL596TTR TSSOP24 (Tape & Reel) 2500 parts per reel STP16CL596XTTR TSSOP24 Exposed-Pad (Tape & Reel) 2500 parts per reel July 2005 Rev. 8 1/18
2 Table 2: Current Accuracy Current accuracy Output Voltage Output Current Between bits Between ICs 0.7V ± 3% ± 10% 15 to 90 ma Figure 1: Pin Connection (Note 1) Note 1: The exposed Pad is electrically not connected. Table 3: Pin Description PIN N Symbol Name and Function 1 GND Ground Terminal 2 SDI Serial data input terminal 3 CLK Clock input terminal 4 /LE Latch input terminal 5-20 OUT 0-15 Output terminal 21 /OE Input terminal of output enable (active low) 22 SDO Serial data out terminal 23 R-EXT Input terminal of an external resistor for constant current programing 24 V DD Supply voltage terminal 2/18
3 Table 4: Absolute Maximum Ratings Symbol Parameter Value Unit V DD Supply Voltage 0 to 7 V V O Output Voltage -0.5 to 16 V I O Output Current 90 ma V I Input Voltage -0.4 to V DD +0.4 V I GND GND Terminal Current 1440 ma f CLK Clock Frequency 25 MHz T OPR Operating Temperature Range -40 to +125 C T STG Storage Temperature Range -65 to +150 C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Under these conditions, functional operation is not implied. Table 5: Thermal Data Symbol Parameter DIP-24 SO-24 TSSOP24 TSSOP24 (*) (exposed pad) Unit R thj-amb Thermal Resistance Junction-ambient C/W (*) The exposed pad should be soldered directly to the PCB to realize the thermal benefits. Table 6: Recommended Operating Conditions Symbol Parameter Test Conditions Min. Typ. Max. Unit V DD Supply Voltage V V O Output Voltage 16.0 V I O Output Current OUTn 5 90 ma I OH Output Current SERIAL-OUT +1 ma I OL Output Current SERIAL-OUT -1 ma V IH Input Voltage 0.7V DD V DD +0.3 V V IL Input Voltage V DD V t wlat /LE Pulse Width V DD = 3.0 to 3.6V 20 ns t wclk CLK Pulse Width 20 ns t wen /OE Pulse Width 400 ns t SETUP(D) Setup Time for DATA 20 ns t HOLD(D) Hold Time for DATA 15 ns t SETUP(L) Setup Time for LATCH 15 ns f CLK Clock Frequency Cascade Operation 25 MHz 3/18
4 Table 7: Electrical Characteristics (V DD =3V, T = 25 C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit V IH Input Voltage High Level 0.7V DD V DD V V IL Input Voltage Low Level GND 0.3V DD V I OH Output Leakage Current V OH = 16 V 10 µa V OL Output Voltage (Serial-OUT) I OL = 1mA 0.4 V V OH Output Voltage (Serial-OUT) I OH = -1mA V DD -0.4V V I OL1 Output Current V O = 0.7V R EXT = 910 Ω ma I OL2 V O = 0.7V R EXT = 360 Ω ma I OL1 Output Current Error V O = 0.7V R EXT = 910 Ω ± 4 ± 5 % I OL2 between bit (All Output ON) V O = 0.7V R EXT = 360 Ω ± 3 ± 4 % R SIN(up) Pull-up Resistor KΩ R SIN(down) Pull-down Resistor KΩ I DD(OFF1) Supply Current (OFF) R EXT = OPEN OUT 0 to 15 = OFF ma I DD(OFF2) R EXT = 470 Ω OUT 0 to 15 = OFF I DD(OFF3) R EXT = 250 Ω OUT 0 to 15 = OFF I DD(ON1) Supply Current (ON) R EXT = 470 Ω OUT 0 to 15 = ON I DD(ON2) R EXT = 250 Ω OUT 0 to 15 = ON Table 8: Switching Characteristics (V DD =3V, T = 25 C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit t PLH1 Propagation Delay Time, V DD = 3 V V IH = V DD ns t PLH2 CLK-OUTn, /LE = H, /OE = L V IL = GND C L = 13pF Propagation Delay Time, /LE-OUTn, /OE = L I O = 40mA V L = 3 V ns t PLH3 Propagation Delay Time, R EXT = 470 Ω R L = 65 Ω ns /OE-OUTn, /LE = H t PLH Propagation Delay Time, ns CLK-SDO t PHL1 Propagation Delay Time, ns CLK-OUTn, /LE = H, /OE = L t PHL2 Propagation Delay Time, ns /LE-OUTn, /OE = L t PHL3 Propagation Delay Time, ns /OE-OUTn, /LE = H t PHL Propagation Delay Time, ns CLK-SDO t r Output Rise Time ns t f Output Fall Time ns 4/18
5 EQUIVALENT CIRCUIT OF INPUTS AND OUTPUTS Figure 2: /OE Terminal Figure 3: /LE Terminal Figure 4: CLK, SDI Terminal 5/18
6 Figure 5: SDO Terminal Figure 6: Block Diagram 6/18
7 Table 9: Truth Table CLOCK /LE /OE SERIAL-IN OUT0... OUT7... OUT15 SDO H L Dn Dn... Dn Dn -15 Dn - 15 L L Dn + 1 No Change Dn - 14 H L Dn + 2 Dn Dn Dn -13 Dn - 13 X L Dn + 3 Dn Dn Dn -13 Dn - 13 X L Dn + 3 OFF Dn - 13 Note 1: OUT0 to OUT15 = ON when Dn = H; OUT0 to OUT15 = OFF when Dn = L. Figure 7: Timing Diagram Note: The latches circuit holds data when the LE terminal is Low. When LE terminal is at High level, latch circuit doesn t hold the data it passes from the input to the output. When OE terminal is at Low level, output terminals OUT0 to OUT15 respond to the data, either ON or OFF. When OE terminal is at High level, it switches off all the data on the output terminal. 7/18
8 Figure 8: Clock, Serial-in, Serial-out Figure 9: Clock, Serial-in, Latch, Enable, Outputs 8/18
9 Figure 10: Outputs TEST CIRCUIT Figure 11: DC Characteristic Figure 12: AC Characteristic 9/18
10 Figure 13: Output Current-R EXT Resistor Figure 14: Power Dissipation vs Temperature Package 10/18
11 Plastic DIP-24 (0.25) MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A A A B B c D E E e E L M E E1 A1 A2 L A B B1 e Stand-off e1 D c ,38 Gage Plane M /D 11/18
12 SO-24 MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A A B C D E e H h L k ddd C 12/18
13 TSSOP24 EXPOSED PAD MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A A A b c D D E E E e K L C 13/18
14 TSSOP24 MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A A A b c D E e 0.65 BSC BSC H K L A A2 A1 b e c K L H D E PIN 1 IDENTIFICATION B 14/18
15 Tape & Reel SO-24 MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A C D N T Ao Bo Ko Po P /18
16 Tape & Reel TSSOP24 MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A C D N T Ao Bo Ko Po P /18
17 Table 10: Revision History Date Revision Description of Changes 06-May Table 6 and Table 7 parameters changed 03-Aug Figure 14 - pag. 10 is changed. 31-Mar Mistake on Fig May Typing Error on the description features. 22-Jul Add note on Fig. 1 and Table 5. 17/18
18 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners 2005 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 18/18
STP08CL596 LOW VOLTAGE 8-BIT CONSTANT CURRENT LED SINK DRIVER
LOW VOLTAGE 8-BIT CONSTANT CURRENT LED SINK DRIVER LOW VOLTAGE POWER SUPPLY DOWN TO 3V 8 CONSTANT CURRENT OUTPUT CHANNELS ADJUSTABLE OUTPUT CURRENT THROUGH EXTERNAL RESISTOR SERIAL DATA IN/PARALLEL DATA
Obsolete Product(s) - Obsolete Product(s)
Low voltage 16-Bit, constant current LED sink driver Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
Order codes Package Packaging
Low voltage, low current power 8-bit shift register Features Low voltage power supply down to 3 V 8 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
STP16CPS05. Low voltage 16-Bit constant current LED sink driver with auto power saving. Features. Description. Order codes
Low voltage 16-Bit constant current LED sink driver with auto power saving Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor
Order codes Package Packaging
Low voltage 16-bit constant current LED sink driver Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
Order codes Package Packaging
Low voltage 8-bit constant current LED sink with full outputs error detection Features Low voltage power supply down to 3 V 8 constant current output channels Adjustable output current through external
Low voltage 16-bit constant current LED sink driver with outputs error detection. Description. Table 1. Device summary. Order codes Package Packaging
Low voltage 16-bit constant current LED sink driver with outputs error detection Features QSOP-24 TSSOP24 SO-24 TSSOP24 (exposed pad) Low voltage power supply down to 3 V 16 constant current output channels
Low voltage 8-bit constant current LED sink with full outputs error detection. Order codes Package Packaging
Low voltage 8-bit constant current LED sink with full outputs error detection Features DIP-16 TSSOP16 Low voltage power supply down to 3 V 8 constant current output channels Adjustable output current through
Obsolete Product(s) - Obsolete Product(s)
TRIPLE 3-INPUT NOR GATE HIGH SPEED: t PD = 4.1 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
74VHC20 DUAL 4-INPUT NAND GATE
DUAL 4-INPUT NAND GATE HIGH SPEED: t PD = 3.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIVE OR GATE MEDIUM-SPEED OPERATION t PHL =t PLH = 70ns (Typ.) at CL = 50 pf and V DD = 10V QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V AND 15V PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I
74VHC08 QUAD 2-INPUT AND GATE
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
74VHC174 HEX D-TYPE FLIP FLOP WITH CLEAR
HEX D-TYPE FLIP FLOP WITH CLEAR HIGH SPEED: f MAX = 175MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.7 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
74VHCT00ATTR QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 5 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
74LVX257 LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER (3-STATE) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER (3-STATE) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD =5.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS POWER-DOWN PROTECTION ON INPUTS INPUT VOLTAGE LEVEL: V IL
HCF4020B RIPPLE-CARRY BINARY COUNTER/DIVIDERS 14 STAGE
RIPPLE-CARRY BINARY COUNTER/DIVIDERS 14 STAGE MEDIUM SPEED OPERATION: 16MHz (Typ.) at V DD = 10V FULLY STATIC OPERATION COMMON RESET BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS
74LCX374 OCTAL D-TYPE FLIP FLOP NON-INVERTING (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS
OCTAL D-TYPE FLIP FLOP NON-INVERTING (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: f MAX = 150 MHz (MIN.) at V CC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS
74LVQ280 9 BIT PARITY GENERATOR
9 BIT PARITY GENERATOR HIGH SPEED: t PD = 8 ns (TYP.) at V CC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: I CC = 2µA(MAX.) at T A =25 C LOW NOISE: V OLP = 0.3V (TYP.) at V CC = 3.3V 75Ω
Obsolete Product(s) - Obsolete Product(s)
HIGH SPEED: f MAX = 180 MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT
74LVX05 LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS INPUT VOLTAGE LEVEL: V IL =0.8V, V IH =2V at V CC =3V LOW POWER DISSIPATION:
HCF4050B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME : t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION HIGH "SINK" AND "SOURCE" CURRENT CAPABILITY QUIESCENT CURRENT
74VHC132 QUAD 2-INPUT SCHMITT NAND GATE
QUAD 2-INPUT SCHMITT NAND GATE HIGH SPEED: t PD = 3.9 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C TYPICAL HYSTERESIS: V h = 1V at V CC = 4.5V POWER DOWN PROTECTION ON
HCF4094B 8 STAGE SHIFT AND STORE BUS REGISTER WITH 3-STATE OUTPUTS
8 STAGE SHIFT AND STORE BUS REGISTER WITH 3-STATE OUTPUTS 3-STATE PARALLEL OUTPUTS FOR CONNECTION TO COMMON BUS SEPARATE SERIAL OUTPUTS SYNCHRONOUS TO BOTH POSITIVE AND NEGATIVE CLOCK EDGES FOR CASCADING
74V1G77CTR SINGLE D-TYPE LATCH
SINGLE D-TYPE LATCH HIGH SPEED: t PD = 4.4ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL
74LCX257 LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER WITH 5V TOLERANT INPUTS AND OUTPUTS (3-STATE)
LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER WITH 5V TOLERANT INPUTS AND OUTPUTS (3-STATE) 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: t PD = 6.0 ns (MAX.) at V CC = 3V POWER DOWN PROTECTION ON INPUTS AND
74LVC373ATTR OCTAL D-TYPE LATCH HIGH PERFORMANCE
OCTAL D-TYPE LATCH HIGH PERFORMANCE 5V TOLERANT INPUTS HIGH SPEED: t PD = 6.8 (MAX.) at V CC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: I OH = I OL = 24mA (MIN) at V
74LVQ14 LOW VOLTAGE CMOS HEX SCHMITT INVERTER
LOW VOLTAGE CMOS HEX SCHMITT INVERTER HIGH SPEED: t PD = 6 ns (TYP.) at V CC = 3.3 V HYSTERESIS INPUT VOLTAGE: V H = 650mV (TYP.) at V CC = 3.0 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: I CC
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NOR GATE HIGH SPEED: t PD = 3.6ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
74V1G00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.7ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT
74V1G79CTR SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP
SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP HIGH SPEED: f MAX = 180MHz (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER
STG719 LOW VOLTAGE 4Ω SPDT SWITCH
LOW VOLTAGE 4Ω SPDT SWITCH HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 5V t PD = 0.4ns (TYP.) at V CC = 3.3V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C LOW "ON" RESISTANCE: R ON = 4Ω (MAX. T A
74V1T00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP HIGH SPEED: f MAX = 180MHz (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX)
HCF4585B 4-BIT MAGNITUDE COMPARATOR
4-BIT MAGNITUDE COMPARATOR EXPANSION TO 8, 12, 16...4 N BITS BY CASCADING UNIT MEDIUM SPEED OPERATION : COMPARES TWO 4-BIT WORDS IN 180ns (Typ.) at 10V STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line receiver Features CMOS design for low power ± 0.2 V sensitivity over input common mode voltage range Typical propagation delay: 19 ns Typical input hysteresis: 60 mv
74LX1G132CTR SINGLE 2-INPUT SCHMITT NAND GATE
SINGLE 2-INPUT SCHMITT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 5.5ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C TYPICAL HYSTERESIS: V h =1V at V CC =4.5V POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.8ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
Obsolete Product(s) - Obsolete Product(s)
HEX INVERTER (SINGLE STATE) HIGH SPEED: t PD = 5ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 10% V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
Obsolete Product(s) - Obsolete Product(s)
SYNCHRONOUS PARALLEL OR SERIAL IN/SERIAL OUT 8 - STAGE STATIC SHIFT REGISTER MEDIUM SPEED OPERATION : 12 MHz (Typ.) At V DD = 10V FULLY STATIC OPERATION 8 MASTER-SLAVE FLIP-FLOPS PLUS OUTPUT BUFFERING
HCF40107B DUAL 2-INPUT NAND BUFFER/DRIVER
DUAL 2-INPUT NAND BUFFER/DRIVER 32 TIMES STANDARD B-SERIES OUTPUT CURRENT DRIVE SINKING CAPABILITY - 136 ma TYP. AT V DD = 10V, V DS = 1V QUIESCENT CURRENT SPECIF. UP TO 20V 5V, 10V AND 15V PARAMETRIC
Obsolete Product(s) - Obsolete Product(s)
SINGLE INVERTER (OPEN DRAIN) HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
Obsolete Product(s) - Obsolete Product(s)
DUAL BINARY UP COUNTER MEDIUM SPEED OPERATION : 6MHz (Typ.) at 10V POSITIVE -OR NEGATIVE- EDGE TRIGGERING SYNCHRONOUS INTERNAL CARRY PROPAGATION QUIESCENT CURRENT SPECIF. UP TO 20V 5V, 10V AND 15V PARAMETRIC
STG3699AQTR LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE
LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE HIGH SPEED: t PD = 1.5ns (TYP.) at V CC = 3.0V t PD = 1.5ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
HCF4041UB QUAD TRUE/COMPLEMENT BUFFER
QUAD TRUE/COMPLEMENT BUFFER BALANCED SINK AND SOURCE CURRENT: APPROXIMATELY 4 TIMES STANDARD "B" DRIVE EQUALIZED DELAY TO TRUE AND COMPLEMENT OUTPUTS QUIESCENT CURRENT SPECIFIED UP TO 20V STANDARDIZED
Obsolete Product(s) - Obsolete Product(s)
QUAD 2 INPUT NAND GATE PROPAGATION DELAY TIME t PD = 60ns (Typ.) at V DD = 10V BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STG3684
LOW VOLTAGE 0.5Ω MAX DUAL SPDT SWITCH WITH BREAK BEFORE MAKE FEATURE HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 3.0V t PD = 0.4ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
74LCX646TTR LOW VOLT. CMOS OCTAL BUS TRANSCEIVER/REGISTER WITH 5 VOLT TOLERANT INPUTS AND OUTPUTS(3-STATE)
74LCX646 LOW VOLT. CMOS OCTAL BUS TRANSCEIVER/REGISTER WITH 5 VOLT TOLERANT INPUTS AND OUTPUTS(3-STATE) 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: t PD = 7.0 ns (MAX.) at V CC = 3V POWER DOWN PROTECTION
ST232 5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS
5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS SUPPLY VOLTAGE RANGE: 4.5 TO 5.5V SUPPLY CURRENT NO LOAD (TYP): 5mA TRANSMITTER OUTPUT VOLTAGE SWING (TYP): ±7.8V CONTROLLED OUTPUT SLEW RATE RECEIVER
HCF4072B DUAL 4 INPUT OR GATE
DUAL 4 INPUT OR GATE MEDIUM SPEED OPERATION : t PD = 60ns (TYP.) at DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A =
74VHCT16244ATTR 16-BIT BUS BUFFER WITH 3-STATE OUTPUTS (NON INVERTED)
16-BIT BUS BUFFER WITH 3-STATE OUTPUTS (NON INVERTED) HIGH SPEED: t PD = 5.4 ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =4µA (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V (MIN.) V IL
74V1T126CTR SINGLE BUS BUFFER (3-STATE)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.6ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN
Order codes Package Packaging
Low voltage 16-bit constant current LED sink driver Datasheet production data Features 16 constant current output channels Adjustable output current through external resistor Output current: 5 ma to 90
74AC10B TRIPLE 3-INPUT NAND GATE
TRIPLE 3-INPUT NAND GATE HIGH SPEED: t PD = 4ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) 50Ω TRANSMISSION LINE DRIVING
74AC00B QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 4ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) 50Ω TRANSMISSION LINE DRIVING
74ACT00B QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 4.5ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS V IH = 2V (MIN.), V IL = 0.8V (MAX.) 50Ω TRANSMISSION
Obsolete Product(s) - Obsolete Product(s)
SINGLE SCHMITT INERTER HIGH SPEED: t PD = 4.3ns (TYP.) at CC =5 LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C TYPICAL HYSTERESIS: h =1 at CC =4.5 POWER DOWN PROTECTION ON INPUT SYMMETRICAL OUTPUT
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line driver Features TTL input compatible Typical propagation delay: 6 ns Typical output skew: 0.5 ns Output will not load line when V CC = 0 V Meets the requirements of
MC1488 RS-232C QUAD LINE DRIVER
RS-232C QUAD LINE DRIVER CURRENT LIMITED OUTPUT ±10mA TYP. POWER-OFF SOURCE IMPEDANCE 300Ω MIN. SIMPLE SLEW RATE CONTROL WITH EXTERNAL CAPACITOR FLEXIBLE OPERATING SUPPLY RANGE INPUTS ARE TTL AND µp COMPATIBLE
Obsolete Product(s) - Obsolete Product(s)
RS-232 quad line driver General features Current limited output ±10mA typ. Power-off source impedance 300Ω min. Simple slew rate control with external capacitor Flexible operating supply range Inputs are
HCF4527B BCD RATE MULTIPLEXER
BCD RATE MULTIPLEXER CASCADABLE IN MULTIPLES OF 4-BITS SET TO 9 INPUT AND 9 DETECT OUTPUT QUIESCENT CURRENT SPECIFIED UP TO 20V STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS 5V, 10V AND 15V PARAMETRIC
Obsolete Product(s) - Obsolete Product(s)
HEX BUFFER/CONVERTER (INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT CAPABILITY
HCF4099B 8 BIT ADDRESSABLE LATCH
8 BIT ADDRESSABLE LATCH SERIAL DATA INPUT - ACTIVE PARALLEL OUTPUT STORAGE REGISTER CAPABILITY - MASTER CLEAR CAN FUNCTION AS DEMULTIPLEXER QUIESCENT CURRENT SPECIFIED UP TO 20V STANDARDIZED SYMMETRICAL
HCF4000B DUAL 3-INPUT NOR GATE PLUS INVERTER
DUAL 3-INPUT NOR GATE PLUS INERTER PROPAGATION DELAY TIME t PD = 50ns (TYP.) at DD = 10 C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED
HCF4012B DUAL 4 INPUT NAND GATE
DUAL 4 INPUT NAND GATE PROPAGATION DELAY TIME t PD = 60ns (Typ.) at DD = 10 BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15
74LX1G04BJR LOW VOLTAGE CMOS SINGLE INVERTER WITH 5V TOLERANT INPUT
LOW VOLTAGE CMOS SINGLE INVERTER WITH 5V TOLERANT INPUT 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.2ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C POWER DOWN PROTECTION ON INPUTS
HCF4018B PRESETTABLE DIVIDE-BY-N COUNTER
PRESETTABLE DIVIDE-BY-N COUNTER MEDIUM SPEED OPERATION 10 MHz (Typ.) at V DD - V SS = 10V FULLY STATIC OPERATION STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V,
M74HC51TTR DUAL 2 WIDE 2 INPUT AND/OR INVERT GATE
DUAL 2 WIDE 2 INPUT AND/OR INVERT GATE HIGH SPEED: t PD = 11ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL
M74HC10TTR TRIPLE 3-INPUT NAND GATE
TRIPLE 3-INPUT NAND GATE HIGH SPEED: t PD = 8ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 8ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
74AC74B DUAL D-TYPE FLIP FLOP WITH PRESET AND CLEAR
DUAL D-TYPE FLIP FLOP WITH PRESET AND CLEAR HIGH SPEED: f MAX = 300MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) 50Ω
Obsolete Product(s) - Obsolete Product(s)
16-BIT BUS BUFFER (NON INVERTED) WITH 3-STATE OUTPUTS, 5V TOLERANT INPUT HIGH SPEED: t PD = 5.3 ns (TYP.) at V CC =3V 5V TOLERANT INPUT LOW POWER DISSIPATION: I CC =4µA (MAX.) at T A =25 C INPUT VOLTAGE
Low voltage 16-bit constant current LED sink driver with output error detection and auto power-saving for automotive applications.
Low voltage 16-bit constant current LED sink driver with output error detection and auto power-saving for automotive applications Description Datasheet - production data The STAP16DPS05 is a monolithic,
74AC257B QUAD 2 CHANNEL MULTIPLEXER (3-STATE)
QUAD 2 CHANNEL MULTIPLEXER (3-STATE) HIGH SPEED: t PD = 4.5ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) 50Ω TRANSMISSION
M74HCT574TTR OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT NON INVERTING
OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT NON INVERTING HIGH SPEED: f MAX = 50MHz (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.)
HCF4040B RIPPLE-CARRY BINARY COUNTER/DIVIDERS 12 STAGE
RIPPLE-CARRY BINARY COUNTER/DIVIDERS 12 STAGE MEDIUM SPEED OPERATION : t PD = 80ns (TYP.) at V DD = 10V FULLY STATIC OPERATION COMMON RESET BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS
Obsolete Product(s) - Obsolete Product(s)
High speed differential line receivers Features Meets or exceeds the requirements of ansi TIA/EIA-644 standard Operates with a single 3.3 V supply Designed for signaling rate up to 400 Mbps Differential
74V1T07CTR SINGLE BUFFER (OPEN DRAIN)
SINGLE BUFFER (OPEN DRAIN) HIGH SPEED: t PD = 4.3ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN PROTECTION
HCF4093. QUAD 2-input NAND Schmidt trigger. Features. Description
QUAD 2-input NAND Schmidt trigger Features Schmidt trigger action on each input with no external components Hysteresis voltage typically 0.9 V at V DD =5V and 2.3 V at V DD =10 V Noise immunity greater
Obsolete Product(s) - Obsolete Product(s)
QUAD 2 CHANNEL MULTIPLEXER HIGH SPEED: t PD = 10ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
ST755 ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS
ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS 2.7V TO 11V INPUT TO ADJUSTABLE NEGATIVE OUTPUT CONVERSION 1W GUARANTEED OUTPUT POWER (V I >4.5V,T 70 C) 68% TYP. EFFICENCY AT 6V VERY LOW
HCF4077B QUAD EXCLUSIVE NOR GATE
QUAD EXCLUSIE NOR GATE MEDIUM-SPEED OPERATION t PHL =t PLH = 65ns (Typ.) at CL = 50 pf and DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA
Order code Temperature range Package Packaging
Low power high speed RS-485/RS-422 transceiver Features Low supply current: 5 ma max -7 V to 12 V common mode input voltage range 70 mv typical input hysteresis Designed for 25 Mbps operation Operate from
HCF4015B DUAL 4-STAGE STATIC SHIFT REGISTER WITH SERIAL INPUT/PARALLEL OUTPUT
DUAL 4-STAGE STATIC SHIFT REGISTER WITH SERIAL INPUT/PARALLEL OUTPUT MEDIUM SPEED OPERATION 12 MHz (Typ.) CLOCK RATE AT V DD - V SS = 10V FULLY STATIC OPERATION 8 MASTER-SLAVE FLIP-FLOPS PLUS INPUT AND
Obsolete Product(s) - Obsolete Product(s)
DUAL 4-STAGE STATIC SHIFT REGISTER WITH SERIAL INPUT/PARALLEL OUTPUT MEDIUM SPEED OPERATION 12 MHz (Typ.) CLOCK RATE AT V DD - V SS = 10V FULLY STATIC OPERATION 8 MASTER-SLAVE FLIP-FLOPS PLUS INPUT AND
74LCX139 Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features Description Order codes
Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features 5V tolerant inputs High speed: t PD = 6.2ns (Max) at V CC = 3V Power down protection on inputs and outputs Symmetrical output impedance: I
LDRxxyy VERY LOW DROP DUAL VOLTAGE REGULATOR
VERY LOW DROP DUAL VOLTAGE REGULATOR OUTPUT CURRENT 1 UP TO 500mA OUTPUT CURRENT 2 UP TO 1.0A LOW DROPOUT VOLTAGE 1 (0.3V @ I O =500mA) LOW DROPOUT VOLTAGE 2 (0.4V @ I O =1A) VERY LOW SUPPLY CURRENT (TYP.50µA
74AC244B OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED)
OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) HIGH SPEED: t PD = 3.8ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.)
74ACT157TTR QUAD 2 CHANNEL MULTIPLEXER
QUAD 2 CHANNEL MULTIPLEXER HIGH SPEED: t PD = 5.5 ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS V IH = 2V (MIN.), V IL = 0.8V (MAX.) 50Ω TRANSMISSION
M74HC164TTR 8 BIT SIPO SHIFT REGISTER
8 BIT SIPO SHIFT REGISTER HIGH SPEED : f MAX = 62MHz (TYP.) at V CC =6V LOW POWER DISSIPATION: I CC =4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL =28%V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
TDA7231A 1.6W AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LOW QUIESCENT CURRENT HIGH POWER CAPABILITY LOW CROSSOVER DISTORTION SOFT CLIPPING
1.6 AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LO QUIESCENT CURRENT. HIGH POER CAPABILITY LO CROSSOVER DISTORTION SOFT CLIPPING DESCRIPTION The is a monolithic integrated circuit in 4 + 4 lead minidip
M74HC4049TTR HEX BUFFER/CONVERTER (INVERTER)
HEX BUFFER/CONVERTER (INVERTER) HIGH SPEED: t PD = 8ns (TYP.) at V CC =6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
HCF40100B 32-STAGE STATIC LEFT/RIGHT SHIFT REGISTER
32-STAGE STATIC LEFT/RIGHT SHIFT REGISTER FULLY STATIC OPERATION SHIFT LEFT/SHIFT RIGHT CAPABILITY MULTIPLE PACKAGE CASCADING RECIRCULATE CAPABILITY LIFO OR FIFO CAPABILITY STANDARDIZED SYMMETRICAL OUTPUT
LM217L LM317L LOW CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR
LM217L LM317L LOW CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE: 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 100 ma LINE REGULATION TYP. 0.01% LOAD REGULATION TYP. 0.1% THERMAL OVERLOAD
M74HCT02TTR QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE HIGH SPEED: t PD = 15 ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) BALANCED PROPAGATION
74ACT240TTR OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (INVERTED)
OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (INVERTED) HIGH SPEED: t PD = 5ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS V IH = 2V (MIN.), V IL = 0.8V
DIP14 Tube LM2901N LM2901D/LM2901DT SO-14 Tube or Tape & Reel
LM2901 Low Power Quad Voltage Comparator Wide single supply voltage range or dual supplies for all devices: +2V to +36V or ±1V to ±18V Very low supply current (1.1mA) independent of supply voltage (1.4mW/comparator