XMT-G (GPS Synchronized) TRANSMITTER CONTROLLER MANUAL

Size: px
Start display at page:

Download "XMT-G (GPS Synchronized) TRANSMITTER CONTROLLER MANUAL"

Transcription

1 XMT-G (GPS Synchronized) TRANSMITTER CONTROLLER MANUAL Zonge International, Inc East Fort Lowell Road, Tucson, AZ USA Tel:(520) Fax:(520)

2 Note: This manual will cover the operation of the new XMT-G (GPS) Transmitter Controller. It is assumed the user is familiar with the XMT-32S (standard XMT) manual and usage. This manual primarily covers the differences between the XMT-G and the XMT-32S. Overview: The XMT-G is a GPS-locked controller for Zonge transmitters. In addition to location, the GPS satellites provide extremely precise timing information. This allows the XMT-G to be held in sync with a similarly equipped GDP-32(G) in a remote location without the use of a (possibly kilometers long) synchronization cable. Operation: The GPS synchronization of the XMT-G is completely autonomous and does not require tuning or setup. Information is, however, provided to the user to determine that the synchronization is operating correctly. The only setup necessary is that of any XMT, namely the desired Period & Duty settings. Controls and Front-Panel Connectors: (numbers in parentheses correspond to labels on graphic) (1) Charge connector: This will accept a connection from a Zonge UC-2 charger (lead-acid battery models), or a UC-LI charger (lithium battery models). The connector is keyed to prevent a mismatch between charger and batteries; do not force the wrong connector to mate. Lead-acid batteries may be charged while the unit is powered, to ensure a full charge with lithium batteries, please power down before charging. XMT-G Manual Zonge International Page 2

3 (2) Re-Sync / Tx-Off Button: The reset switch will DISABLE the transmitter output immediately by setting the Duty pin to 5 Volts. When the GPS/Manual Sync Switch (5) is in the Gps" position, it will also reboot all the Gps and synchronization circuitry into a known state, and restart the synchronization process, which may take a few minutes to complete. Do not attempt to transmit during this time (unless utilizing manual synchronization) as the transmitter and GDP will not be synchronized in time until complete. When the Gps/Manual Sync Switch (5) is in the Manual" position, pressing this switch initiates a manual synchronization between the XMT and GDP. (3) Duty Cycle Switch: Switches from 50% to 100% Duty cycle. Note that changes made from the duty cycle menu will override the setting of this switch, and, conversely, toggling this switch will override any selections made from the duty cycle menu. (4) Phase / Batt Switch: Batt setting shows the battery voltage on the meter, in Volts. Phase setting shows the relative difference between XMT Period (internal) and GDP Period (external on "I/O" connector), a meter reading of mid-scale (12) is desired when GPS's are locked and in sync. An exact reading of the phase difference is available on the LCD (see below). (5) GPS Sync / Manual Sync Switch: Must be on "Time Series" to utilize GPS synchronization. In the "Manual" position, operation is identical to the original XMT-32S, and the GPS is ignored (although GPS status such as UTC time and latitude/longitude is still available). Note that toggling this switch to the GPS position after manual synchronization will de-synchronize the XMT and GDP, and necessitate an additional manual synchronization procedure. For this reason, this is a locking switch; lift up on the actuator to toggle the switch. (6) Mode Button: Used to cycle through types of available information on the LCD (see below). (7) Up Button: Used to cycle through items on an LCD menu, or to change Period & Duty (when in Period/Duty mode, indicated by the current setting for Period on the LCD). (8) Down Button: Same as Up button, reverse order. (6+7+8) GPS Reset & ReSurvey: Moving the XMT requires a re-survey (30 minute average) of the exact location in order to produce accurate time. This should begin automatically, but can be started manually by holding the three "Mode", "Up", and "Down" buttons in simultaneously. The operator should then see "RESVY?10" on the display, and has 10 seconds to press the "Reset" button to initiate a resurvey. Note that, once again, this process will take approximately 30 minutes to complete, and is irreversible. (9) Meter: When the Phase/Batt Switch (4) is in the Battery position, this displays the battery voltage in volts. Note that lead acid batteries are considered in need of charge below 11V, whereas lithium cells retain very little capacity below 13V. When the Phase/Batt Switch (4) is in the Phase position, and the GPS/Manual Sync Switch (5) is in the Manual position, the meter indicates the relative manual synchronization state between the crystal oscillator in the XMT XMT-G Manual Zonge International Page 3

4 and that in the connected GDP. This is a detailed procedure; please see GDP manual for further information. (10) Power switch: Connects or disconnects the battery from the XMT electronics and crystal oscillator. When in manual sync mode, the GDP and XMT will need to be manually resynchronized with every power cycle - for this reason, the power switch contains a locking pin to prevent accidental power cycling. To operate the power switch, pull the locking pin out of the face of the switch with a thumbnail and rotate the switch. (11) Sync Out Banana Jacks: A buffered version of the transmitter control signal ( Period in Zonge nomenclature) is present on these connectors for use in the XMT <-> GDP manual synchronization procedure. (12) Internal GPS Antenna Connector [not shown]: The coaxial cable from the embedded GPS antenna on the lid of the XMT is typically connected here. Alternative antennas could also be utilized, but connecting them to the N coaxial connector at the rear of the XMT allows the lid to be closed to keep the controls clean during operation. (13) Internal wireless antenna connector [not shown]: The coaxial cable from the embedded wireless antenna on the lid of the XMT is typically connected here. If communication between the XMT control software on a laptop computer and the XMT cannot be established, check this connection to ensure it has not loosened during operation. (14) Battery compartment [not shown]: The thumbscrews to the right of the main control panel may be removed to replace the battery. (15) Transmitter control connector [not shown]: the cable that connects the transmitter to the XMT is attached here, or alternatively, the sync cable is connected between here and a GDP when performing manual synchronization; the XMT is then relocated to the transmitter s position, and the transmitter control cable is reinserted. (16) External GPS Antenna Connector [not shown]: The coaxial cable from an optional GPS antenna is typically connected here. This is useful in situations where the XMT must be located in a position where the internal antenna on the lid is prevented from seeing a clear view of the sky for acquiring satellites. XMT-G Manual Zonge International Page 4

5 LCD Display and Menus: The LCD display is a multi-function device intended to show status and current settings for all parameters of the XMT-G. The Mode Button switches between main modes / menus, and the Up & Down buttons switch between sub-modes / menus Main modes / menus: GPS: Period: Duty: Time & Date: Versions: Up & Down buttons cycle through all GPS information. Up & Down buttons choose the desired operating Period (Frequency). No sub-menu items, used for adjusting Period only. Up & Down buttons choose the desired operating Duty Cycle (not absolute; given as a percentage of the period). Changing this value will override the setting of the duty cycle toggle switch, and moving the switch will override any selection made via this menu. No sub-menu items, used for adjusting Duty only. Shows the current GPS time, which generally lags UTC (Universal Coordinated Time) (previously Greenwich Mean Time or GMT) by 13 or more seconds, adjusted yearly. Up/Down should cycle between time & date. No sub-menu items. Up & Down cycle through all available version information. Synchronization: Up & Down cycle through sync quality data. Configuration: GPS Menu Items: Survey Status: GPS Lock: Antenna: Allows device behavior to be modified. Any changes made via this menu should persist across power cycles (reboots). "GPS Svyd" indicates that the self-survey required for accurate timing information has been completed, otherwise percent completion is shown. "GPS Lock" indicates that the GPS is fully operational, otherwise any items preceding a successful lock are shown. Note that an almanac is not strictly necessary for accurate timing and will load in minutes of operation. The GPS can detect a missing, cut or shorted GPS antenna cable. "Antna OK" indicates the antenna is operating nominally. Number of Satellites: It is desirable to have at least 5 satellites for a stable synchronization, although as few as 3 may be acceptable in some situations. XMT-G Manual Zonge International Page 5

6 DOP: Latitude: Longitude: Versions Menu Items: Serial Number: SW: FW: GPS: ( Dilution of Precision ): A GPS-centric metric for the quality of the GPS data. Current latitude is shown with "N" or "S" taking place of the decimal point (i.e. 32N2645 indicates or 32,2645 degrees North). Current longitude is shown with "E" or "W" taking place of the decimal point (i.e. 110W9219 indicates or 110,9219 degrees West). Shows device serial number. Shows software build number. Shows firmware build number. Shows GPS firmware revision. Accuracy Menu Items: X: Shows crystal accuracy over last 10 seconds vs. GPS time. Units are parts per billion. Ideal synchronization would show a value of zero. When GPS lock is lost, "NoXtalLK" is shown. Ph: Xtal D/A: Shows difference between internal Period signal, and Period connected to external "I/O" connector (usually GDP), in nanoseconds. Ideal synchronization would show a value of zero. When GPS lock is lost, or no GDP is connected to the I/O port, "PhaseErr" is shown. Shows the current value of the D/A that tunes the internal clock to match the GPS clock. Xtal Freq: Shows current frequency of the internal clock. When fully synchronized in GPS mode, this should reflect the ideal value of Hz. Configuration Menu Items: Root-2 Frequencies: Enable or disable the display/use of the Square-Root-of-2 frequencies. The period menu will cycle through all available modes sequentially; when Root-2 is disabled, this will entail the standard powers-of-2: 1, 2, 4, 8, etc. When Root-2 is enabled, those frequencies will be interleaved in the expected order: 1, 1.4, 2, 2.8, 4, 5.6, 8, etc. XMT-G Manual Zonge International Page 6

7 TRANSMITTER CONTROL INTERFACE (GDP-32 II Manual, Section 18.6) The GGT series transmitters use a twenty milliamp control signal with a rise and fall time of less than one microsecond. There are two control signals used; Transmitter on/off and Polarity. 1. TRANSMITTER ON / OFF. This signal is used in the time domain mode to turn off the transmitter when needed depending on the duty cycle required. 2. POLARITY. This signal controls the output polarity of the transmitter. When the signal is supplied the transmitter reverses the output polarity from the rest state. The timing diagram below shows the relationship between the two signals for a fifty percent duty cycle. Transmitter Control MS Connector: Polarity: A Ground: B, E (Need to be shorted together) Transmitter ON/OFF: C (With no connection, default is ON) Duty cycle: D XMT-G Manual Zonge International Page 7

8 XMT-G Manual Zonge International Page 8

9 Manual Syncing SYNCHRONIZING TIMING CIRCUITS (GDP-32 II Manual, Section 6.2) Frequency Adjust and Synchronizing Operations The timing circuits of the XMT and the GDP-32 II are comprised of an ultra-stabilized MHz oscillator and a digital counter chain providing a binary sequence of frequency divisions. Frequencies on the XMT transmitter controller are selectable from a push-button panel switch. Frequencies on the GDP are selectable from a menu screen under the control of the on-board computer. To ensure that the timing edge of the transmitter controller (i.e. the transmitter output) and the receiver waveforms coincide exactly throughout the day, two adjustments must be made: First, the two MHz crystals must be adjusted to EXACTLY the same frequency to prevent the phase drift. Second, the counter chains in the XMT and GDP-32 II must be reset so that the switching edges of both occur simultaneously (i.e. the waveforms are synchronized.) The GDP uses the counter waveform to determine the polarity of the transmitted waveform and the on/off cycle in the case of time domain. Both of these adjustments require that the synchronization cable be connected between the XMT and GDP-32 II. The synchronization cable connects the GDP-32 II MHz oscillator output to the XMT phase detector. The detector displays the frequency difference between the two oscillators on the XMT meter. Each complete swing of the meter represents one cycle of MHz or 0.2 microseconds ( sec) of time shift. The following table shows the phase shift in milliradians (mr) per meter swing that occur at various frequencies, where: Period = 1/Frequency Period/mr = Period/(6.283*1000) Freq Period Period/mr mr/swing Hz μsec μsec/mr 10.5 mr/swing msec sec msec/mr The above list shows the importance of accurate frequency adjustments for the acquisition of accurate high frequency phase measurements. The frequency match is obtained by performing a Frequency Adjustment as outlined in the section below. Typically, the frequency should be adjusted so that meter drift is less than one division over a 30 second interval. Drift rates of this magnitude yield phase drifts of less than one hundredth of the above values. XMT-G Manual Zonge International Page 9

10 XMT-G Manual Zonge International Page 10

11 XMT-G Manual Zonge International Page 11

12 After the crystal ovens have heated for at least 60 minutes: (GDP-32 II Manual, Section 6.2) 1. Disconnect the Battery Charger. 2. Connect the synchronization cable between the I/O port on the transmitter controller XMT-32 and the TRANSMITTER I/O port on the Control I/O panel of the receiver (Figure 6.3.) 3. Switch the PHASE/BATT switch to the BATT position to check the transmitter controller battery voltage. The voltage should read at least 12.5 volts. If lower, there is either a poorly charged battery or a problem with the power system (GDP-32 II Manual, Section 15 - Maintenance.) 4. Switch the PHASE/BATT switch to the PHASE position. Observe the needle on the PHASE/BATT analog meter. Any needle movement indicates that there is some frequency difference between the GDP-32 II and the XMT-32 oscillators. The faster the needle is swinging, the greater the frequency difference. If there is absolutely no swinging over a period of a minute or so, the oscillators are either adjusted to the exact same frequency, or the oscillators are very different in frequency and the resultant beat frequency is beyond the response of the meter. Frequency adjustment and synchronization are accomplished with the GDP-32 II by executing the Synchronize to XMT function (Utilities Menu - Option 4.) 5. Follow the directions given on the screen. 6. While adjusting the frequency of either instrument, the needle should come to rest near the center of the meter, where it is most sensitive to movement. Use the cursor control keys to adjust the frequency up or down slightly until the needle roughly stabilizes near the center of the scale. 7. Press RESET to synchronize the counter chains of the two instruments. (When synchronizing multiple receivers proceed to step 12.) 8. Press CONTINUE. The GDP-32 II automatically measures the phase difference between the external calibration signal generated by the GDP-32 II and the corresponding signal generated by the XMT. If the two instruments have been properly synchronized, the measured phase difference is close to 0.0 mr. 9. Repeat step 8 several times to check the synchronization. The measured phase difference should remain close to 0.0 mr. 10. Ensure that synchronization can be maintained by disconnecting the synchronization cable and repeating the phase measurement. XMT-G Manual Zonge International Page 12

13 LOSING MANUAL SYNCHRONIZATION Synchronization can be lost in the following circumstances: Switching to GPS Sync Turning off power Losing battery power to either the transmitter controller or the receiver Re-adjusting the OSC TRIM pot on the transmitter controller Malfunction of the timing chain, crystal heater, crystal, timing boards, etc. The GDP or XMT receives a sharp jolt Synchronization is not lost in the following circumstances: Turning off the receiver using Utilities Menu Option 6 Turn Off Power. Re-booting the machine with the SHIFT/RESET sequence Changing frequencies Changing from time domain to frequency domain or vice versa. If synchronization is lost, connect the controller and the receiver using the synchronization cable and re-synchronize. In certain cases, such as in scalar CSAMT, you may be able to avoid this if you are interested only in phase difference between the electric and magnetic field components. Usually, loss of synchronization must be corrected immediately. XMT-G Manual Zonge International Page 13

14 XMT-G Specifications: Power consumption: VDC Endurance: approx 30h with standard 12V, 7.5Ah lead-acid battery; 15h with optional g wifi control. Calibration output: 3.3V, 20mA max, unipolar, synchronous to Period signal Absolute timing accuracy: < 100nS to global GPS UTC time base Cycle-Cycle Timing uncertainty: < 20nS Timing drift, GPS locked: to resolution of GPS constellation Timing drift, manual synchronization: < 1ppb GPS Antenna connection: 3.3-5V LNA 100mA. Compatible with most external amplified L1 antennas, max cable length 10 meters with a Zonge approved antenna. XMT cable should match length of GDP cable to within 1m for best synchronization. XMT-G Manual Zonge International Page 14

XMT-32 TRANSMITTER CONTROLLER MANUAL

XMT-32 TRANSMITTER CONTROLLER MANUAL XMT-32 TRANSMITTER CONTROLLER MANUAL Zonge International 3322 East Fort Lowell Road, Tucson, AZ 85716 USA Tel:(520) 327-5501 Fax:(520) 325-1588 Email:zonge@zonge.com Blank Page XMT-32 Manual Zonge International

More information

ZT-30 ZeroTEM TRANSMITTER MANUAL

ZT-30 ZeroTEM TRANSMITTER MANUAL ZT-30 ZeroTEM TRANSMITTER MANUAL 06 September, 2000 Zonge Engineering and Research Organization, Inc. 3322 East Fort Lowell Road, Tucson, AZ 85716 USA Tel:(520)327-5501 Fax:(520)325-1588 Email:zonge@zonge.com

More information

Model GPS-1 Synchronizer Module Users Manual

Model GPS-1 Synchronizer Module Users Manual Model GPS-1 Synchronizer Module Users Manual 4021 Stirrup Creek Dr. Suite 100 Durham, NC 27703 USA December 2002 Tel 800.849.4447 Rev 1.0 Fax 800.849.2947 Copyright 2002 Highway Information Systems, Inc.

More information

TX CONTROLLER Model EM-IP Quick Start Guide

TX CONTROLLER Model EM-IP Quick Start Guide TX CONTROLLER Model EM-IP Quick Start Guide 860 boul. de la Chaudière, suite 200 Québec (Qc), Canada, G1X 4B7 Tel.: +1 (418) 877-4249 Fax: +1 (418) 877-4054 E-Mail: gdd@gdd.ca Web site: www.gdd.ca Visit

More information

GPS Time and Frequency Reference Receiver

GPS Time and Frequency Reference Receiver $ GPS Time and Frequency Reference Receiver Symmetricom s 58540A GPS time and frequency reference receiver features: Eight-channel, parallel tracking GPS engine C/A Code, L1 Carrier GPS T-RAIM satellite

More information

1 Second Time Base From Crystal Oscillator

1 Second Time Base From Crystal Oscillator 1 Second Time Base From Crystal Oscillator The schematic below illustrates dividing a crystal oscillator signal by the crystal frequency to obtain an accurate (0.01%) 1 second time base. Two cascaded 12

More information

A S M A X - 1 DDS FREQUENCY SYNTHESIZED C-QUAM COMPATIBLE STEREO AM TRANSMITTER. User s Guide (Please read carefully before using for the first time!

A S M A X - 1 DDS FREQUENCY SYNTHESIZED C-QUAM COMPATIBLE STEREO AM TRANSMITTER. User s Guide (Please read carefully before using for the first time! A S M A X - 1 DDS FREQUENCY SYNTHESIZED C-QUAM COMPATIBLE STEREO AM TRANSMITTER User s Guide (Please read carefully before using for the first time!) Copyright 2011 by ASPiSYS Ltd. ASMAX1 is a low-power

More information

BRB900 GPS Telemetry System August 2013 Version 0.06

BRB900 GPS Telemetry System August 2013 Version 0.06 BRB900 GPS Telemetry System August 2013 Version 0.06 As of January 2013, a new model of the BRB900 has been introduced. The key differences are listed below. 1. U-blox GPS Chipset: The Trimble Lassen IQ

More information

ADI-100 Interrupter. Operator s Manual. 526 S. Seminole Bartlesville, OK /

ADI-100 Interrupter. Operator s Manual. 526 S. Seminole Bartlesville, OK / ADI-100 Interrupter Operator s Manual 526 S. Seminole Bartlesville, OK 74003 918/336-1221 www.sescocp.com ADI - 100 Interrupter FEATURES Clock Accuracy 100% during GPS lock Clock Drift 30 µsec per degree

More information

GPS10R - 10 MHz, GPS Disciplined, Rubidium Frequency Standards

GPS10R - 10 MHz, GPS Disciplined, Rubidium Frequency Standards GPS10R - 10 MHz, GPS Disciplined, Rubidium Standards Key Features Completely self-contained units. No extra P.C Multiple 10 MHz Outputs plus other outputs needed. Full information available via LCD. RS232

More information

ThunderBolt Display. by Adam Maurer, VK4GHZ

ThunderBolt Display. by Adam Maurer, VK4GHZ ThunderBolt Display by Adam Maurer, VK4GHZ Overview ThunderBolt Display is a stand-alone microprocessor-controlled LCD specifically for Trimble s ThunderBolt Disciplined Clock, providing a comprehensive

More information

GPS10RBN - 10 MHz, GPS Disciplined Rubidium Frequency Standard

GPS10RBN - 10 MHz, GPS Disciplined Rubidium Frequency Standard GPS10RBN - 10 MHz, GPS Disciplined Rubidium Standard Completely self-contained unit. No extra P.C needed. Full information available via LCD. Rubidium Oscillator locked to GPS satellite signal. Accuracy

More information

AA-35 ZOOM. RigExpert. User s manual. Antenna and cable analyzer

AA-35 ZOOM. RigExpert. User s manual. Antenna and cable analyzer AA-35 ZOOM Antenna and cable analyzer RigExpert User s manual . Table of contents Introduction Operating the AA-35 ZOOM First time use Main menu Multifunctional keys Connecting to your antenna SWR chart

More information

HT101V Reference Manual

HT101V Reference Manual HT101V Reference Manual Overview The HT101V from Ag-Tester is our handheld tester designed to diagnose valve components on agricultural machinery. Valves tested include: 1- Boom Control Valves 2- Servo

More information

Configuring the Global Navigation Satellite System

Configuring the Global Navigation Satellite System Configuring the Global Navigation Satellite System uses a satellite receiver, also called the global navigation satellite system (GNSS), as a new timing interface. In typical telecom networks, synchronization

More information

Graphical Control Panel User Manual

Graphical Control Panel User Manual Graphical Control Panel User Manual DS-MPE-DAQ0804 PCIe Minicard Data Acquisition Module For Universal Driver Version 7.0.0 and later Revision A.0 March 2015 Revision Date Comment A.0 3/18/2015 Initial

More information

GPS10RBN-26: 10 MHz, GPS Disciplined, Ultra Low Noise Rubidium Frequency Standard

GPS10RBN-26: 10 MHz, GPS Disciplined, Ultra Low Noise Rubidium Frequency Standard GPS10RBN-26: 10 MHz, GPS Disciplined, Ultra Low Noise Rubidium Standard Key Features Completely self-contained unit. No extra P.C needed. Full information available via LCD. Rubidium Oscillator locked

More information

Microprocessor Control Board Set Up Procedures (OR PLC)

Microprocessor Control Board Set Up Procedures (OR PLC) Microprocessor Control Board Set Up Procedures (OR-00 PLC) SWITCHES/PUSHBUTTONS Push Buttons at display SW Enter button SW Back button SW Down SW UP Back light on/off switch Rotary switches on main board

More information

Design of Simulcast Paging Systems using the Infostream Cypher. Document Number Revsion B 2005 Infostream Pty Ltd. All rights reserved

Design of Simulcast Paging Systems using the Infostream Cypher. Document Number Revsion B 2005 Infostream Pty Ltd. All rights reserved Design of Simulcast Paging Systems using the Infostream Cypher Document Number 95-1003. Revsion B 2005 Infostream Pty Ltd. All rights reserved 1 INTRODUCTION 2 2 TRANSMITTER FREQUENCY CONTROL 3 2.1 Introduction

More information

Keywords: GPS, receiver, GPS receiver, MAX2769, 2769, 1575MHz, Integrated GPS Receiver, Global Positioning System

Keywords: GPS, receiver, GPS receiver, MAX2769, 2769, 1575MHz, Integrated GPS Receiver, Global Positioning System Maxim > Design Support > Technical Documents > User Guides > APP 3910 Keywords: GPS, receiver, GPS receiver, MAX2769, 2769, 1575MHz, Integrated GPS Receiver, Global Positioning System USER GUIDE 3910 User's

More information

Dragon. manual version 1.7

Dragon. manual version 1.7 Dragon manual version 1.7 Contents DRAGON TOP PANEL... 2 DRAGON STARTUP... 2 DRAGON STARTUP SCREEN... 2 DRAGON INFO SCREEN... 3 DRAGON MAIN SCREEN... 3 TURNING ON A TRANSMITTER... 4 CHANGING MAIN SCREEN

More information

Configuring the Global Navigation Satellite System

Configuring the Global Navigation Satellite System Configuring the Global Navigation Satellite System Effective Cisco IOS-XE Release 3.17, the Cisco ASR-920-12SZ-IM router uses a satellite receiver, also called the global navigation satellite system (GNSS),

More information

SIMREX Corporation Your Trusted Wireless Solution Provider

SIMREX Corporation Your Trusted Wireless Solution Provider SIMSYNC Instruction Manual Traffic Controller Time Synchronization System Firmware Release 1.7 SIMREX MAN.SIMSYNC, Rev 8.0 MARCH 2006 Your Trusted Wireless Solution Provider www.simrex.com Introduction

More information

CIC ENGINEERING 345 CENTER STREET EAST PEORIA, IL PH FAX

CIC ENGINEERING 345 CENTER STREET EAST PEORIA, IL PH FAX Micro Multi-Purpose Input Simulator (MPIS) CIC P/N: umpis µmpis Overview The µmpis test box is a general-purpose test box that generates signals used to control the inputs of an electronic control module

More information

MN5020HS Smart GPS Antenna Module

MN5020HS Smart GPS Antenna Module 1 Description The Micro Modular Technologies MN5020HS Smart Global Positioning System (GPS) Antenna Module is a complete 20-channel receiver with an integrated 18 x 18 mm patch antenna. With this highly

More information

OVEN INDUSTRIES, INC. Model 5C7-362

OVEN INDUSTRIES, INC. Model 5C7-362 OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...

More information

TECHNICAL MANUAL TM0110-2

TECHNICAL MANUAL TM0110-2 TECHNICAL MANUAL TM0110-2 RUBIDIUM FREQUENCY STANDARD MODEL FE-5680A SERIES OPTION 2 OPERATION AND MAINTENANCE INSTRUCTIONS Rubidium Frequency Standard Model FE-5680A with Option 2 Frequency Electronics,

More information

Featherweight GPS Tracker User s Manual June 16, 2017

Featherweight GPS Tracker User s Manual June 16, 2017 Featherweight GPS Tracker User s Manual June 16, 2017 Hardware Configuration and Installation The dimensions for the board are provided below, in inches. Note that with the antenna installed, the total

More information

125 Series FTS375 Disciplined Reference and Synchronous Clock Generator

125 Series FTS375 Disciplined Reference and Synchronous Clock Generator Available at Digi-Key www.digikey.com 125 Series FTS375 Disciplined Reference and Synchronous Clock Generator 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851- 4722 Fax: 630-851- 5040 www.conwin.com

More information

Configuring the Global Navigation Satellite System

Configuring the Global Navigation Satellite System Configuring the Global Navigation Satellite System Effective Cisco IOS-XE Release 3.17, the Cisco ASR-920-12SZ-IM router uses a satellite receiver, also called the global navigation satellite system (GNSS),

More information

MAGNETIC FIELD METER Operator s Manual

MAGNETIC FIELD METER Operator s Manual Edition 4.4 September 2011 MAGNETIC FIELD METER 3000 Operator s Manual The MFM 3000 is a professional magnetic field instrument To make the best use of the instrument we recommend that you read this manual

More information

Model Hz to 10MHz Precision Phasemeter. Operating Manual

Model Hz to 10MHz Precision Phasemeter. Operating Manual Model 6610 1Hz to 10MHz Precision Phasemeter Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give long

More information

GPS Time Server Product Specifications and Installation Data

GPS Time Server Product Specifications and Installation Data GPS Time Server Product Specifications and Installation Data 1 DESCRIPTION This document covers Revision C and higher. The HE200TIM100 is a GPS (Global Positioning System) Time Server that monitors GPS

More information

Configuring the Global Navigation Satellite System

Configuring the Global Navigation Satellite System Configuring the Global Navigation Satellite System Effective Cisco IOS-XE Release 3.17, the Cisco ASR 903 (with RSP3 module) and Cisco ASR 907 router uses a satellite receiver, also called the global navigation

More information

Configuring the Global Navigation Satellite System

Configuring the Global Navigation Satellite System Configuring the Global Navigation Satellite System Effective Cisco IOS-XE Release 3.17, the Cisco ASR-920-12SZ-IM router uses a satellite receiver, also called the global navigation satellite system (GNSS),

More information

VX-2100/VX-2200 (UHF) Alignment

VX-2100/VX-2200 (UHF) Alignment VX-2100/VX-2200 (UHF) Introduction The VX-2100/2200 is carefully aligned at the factory for the specified performance across the frequency range specified for each version. Realignment should therefore

More information

Digiair Pro ATSC USER MANUAL

Digiair Pro ATSC USER MANUAL Digiair Pro ATSC USER MANUAL Content: DIGIAIR PRO Description 2 1 GETTING STARTED 3 1.1 POWER ON/OFF 3 1.2 POWER SUPPLY AND BATTERY 3 1.3 HOW TO USE THE METER 3 ATTENUATOR 4 DIGITAL MODE 4 2 DESCRIPTION

More information

MFJ ENTERPRISES, INC.

MFJ ENTERPRISES, INC. Screwdriver Antenna Controller Model MFJ-1926 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel:

More information

Power Meter. Measurement Guide. for Anritsu RF and Microwave Handheld Instruments BTS Master Site Master Spectrum Master Cell Master

Power Meter. Measurement Guide. for Anritsu RF and Microwave Handheld Instruments BTS Master Site Master Spectrum Master Cell Master Measurement Guide Power Meter for Anritsu RF and Microwave Handheld Instruments BTS Master Site Master Spectrum Master Cell Master Power Meter Option 29 High Accuracy Power Meter Option 19 Inline Peak

More information

UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz)

UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz) UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz) Connection and operating instructions 1. Introduction The UDV is the ideal device to adapt older, VFO-controlled transceivers to modern requirements regarding frequency

More information

BFS / BFSM SERIES Installation & Maintenance Manual

BFS / BFSM SERIES Installation & Maintenance Manual Introduction: The BFS / BFSM series electric actuators have battery backup modules for fail safe operation. The BFS series is for two position control and the BFSM series is for proportional control, both

More information

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 Operation and Service Manual Page 2 Manufactured by: LINCAST INTERNATIONAL PTY. LTD. 2/3 Sir Laurence Drive

More information

INC. MICROWAVE. A Spectrum Control Business

INC. MICROWAVE. A Spectrum Control Business DRO Selection Guide DIELECTRIC RESONATOR OSCILLATORS Model Number Frequency Free Running, Mechanically Tuned Mechanical Tuning BW (MHz) +10 MDR2100 2.5-6.0 +10 6.0-21.0 +20 Free Running, Mechanically Tuned,

More information

Cactus V6 Firmware Release Notes

Cactus V6 Firmware Release Notes Cactus V6 Firmware Release Notes Firmware V2.1.001 (Released on 20 Oct 2016) New features: - Added support for V6II / IIS (all firmware versions) and RF60 Master (with firmware version 2.00 or later):

More information

MFJ-249B HF/VHF SWR ANALYZER

MFJ-249B HF/VHF SWR ANALYZER TABLE OF CONTENTS MFJ-249B... 2 Introduction... 2 Powering The MFJ-249B... 3 Battery Installation... 3 Alkaline Batteries... 3 NiCd Batteries... 4 Power Saving Mode... 4 Operation Of The MFJ-249B...5 SWR

More information

ProLink Radio. 900 MHz SDI-12 Data Radio Scienterra Limited. Version A-0x0C-1-AC 20 October 2009

ProLink Radio. 900 MHz SDI-12 Data Radio Scienterra Limited. Version A-0x0C-1-AC 20 October 2009 ProLink Radio 900 MHz SDI-12 Data Radio Scienterra Limited Version A-0x0C-1-AC 20 October 2009 For sales inquiries please contact: ENVCO Environmental Collective 31 Sandringham Rd Kingsland, Auckland 1024

More information

DRTS-6. DRTS-6 has been designed to test: DRTS-6. Advanced Protection Relay Test Set and Measurement System

DRTS-6. DRTS-6 has been designed to test: DRTS-6. Advanced Protection Relay Test Set and Measurement System DRTS-6 Advanced Protection Relay Test Set and Measurement System MULTI-TASKING EQUIPMENT DESIGNED FOR TESTING PROTECTION RELAYS, ENERGY METERS, TRANSDUCERS POWERFUL AND LIGHTWEIGHT HIGH ACCURACY: BETTER

More information

Milliamp Calibrator. Model 434. General description. Calibrate with laboratory accuracy. All 4 to 20 ma loop functions

Milliamp Calibrator. Model 434. General description. Calibrate with laboratory accuracy. All 4 to 20 ma loop functions Milliamp Calibrator Model 434 General description Calibrate Loop Instruments Calibrate and troubleshoot all the signals in a standard 4 to 20 milliamp process control loop with Altek s Model 434 Milliamp

More information

ONCORE ENGINEERING NOTE M12 Oncore

ONCORE ENGINEERING NOTE M12 Oncore ONCORE ENGINEERING NOTE M12 Oncore 1. Product Specifications 2. Basic Description 3. Mechanical 4. Environmental 5. Electrical 6. RF Characteristics of Receiver 7. RF Requirements for Antenna 8. Performance

More information

330 DUAL-CHANNEL CAMERA-MOUNT UHF WIRELESS MICROPHONE SYSTEM

330 DUAL-CHANNEL CAMERA-MOUNT UHF WIRELESS MICROPHONE SYSTEM 330 DUAL-CHANNEL CAMERA-MOUNT UHF WIRELESS MICROPHONE SYSTEM 330UPR - 35BT - 35HT - 35XT INSTRUCTION MANUAL Thank you for purchasing the Azden 330 Dual-Channel Wireless Microphone system. The components

More information

RF4432 wireless transceiver module

RF4432 wireless transceiver module 1. Description www.nicerf.com RF4432 RF4432 wireless transceiver module RF4432 adopts Silicon Lab Si4432 RF chip, which is a highly integrated wireless ISM band transceiver. The features of high sensitivity

More information

Series 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual

Series 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual THE HIGH PERFORMANCE COMPANY Series 70 Hold 1 sec. Hold 1 sec. FOR MORE INFORMATION ON THIS PRODUCT AND OTHER BRAY PRODUCTS PLEASE VISIT OUR WEBSITE www.bray.com Table of Contents 1. Definition of Terms.........................................2

More information

CIPS, DCVG & GPCM Pipeline Surveyor. Corrosion Control Equipment

CIPS, DCVG & GPCM Pipeline Surveyor. Corrosion Control Equipment CIPS, DCVG & GPCM Pipeline Surveyor Corrosion Control Equipment Electronic Pipeline Technology 153 Milos Road Richmond Hill, Ontario, Canada, L4C 0P8 Tel: (905) 918-0025 Fax: (905) 918-0033 www.ep-tech.ca

More information

8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE

8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE 8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE TRANSMILLE LTD. Version 1.1 : Apr 2015 TABLE OF CONTENTS PREPARING FOR CALIBRATION... 4 INTRODUCTION... 4 CALIBRATION INTERVAL SELECTION...

More information

Introduction to Oscilloscopes Instructor s Guide

Introduction to Oscilloscopes Instructor s Guide Introduction to Oscilloscopes A collection of lab exercises to introduce you to the basic controls of a digital oscilloscope in order to make common electronic measurements. Revision 1.0 Page 1 of 25 Copyright

More information

LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display.

LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. Four band MTR 4B shown Overview: The Mountain Topper Rigs are designed to be a very small,

More information

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment:

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment: RUTGERS UNIVERSITY The State University of New Jersey School of Engineering Department Of Electrical and Computer Engineering 332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title:

More information

2006 MFJ ENTERPRISES, INC.

2006 MFJ ENTERPRISES, INC. Model MFJ-842 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION

More information

MAGNETIC FIELD METER Operator s Manual

MAGNETIC FIELD METER Operator s Manual Edition 3.1 2009-09-03 MAGNETIC FIELD METER 2000 Operator s Manual The MFM 2000 is a professional magnetic field instrument To make the best use of the instrument we recommend that you read this manual

More information

DIGIAIR PRO USER MANUAL

DIGIAIR PRO USER MANUAL DIGIAIR PRO USER MANUAL Content: DIGIAIR PRO Description 2 1 GETTING STARTED 3 1.1 POWER ON/OFF 3 1.2 POWER SUPPLY AND BATTERY 3 1.3 HOW TO USE THE METER 3 1.4 ATTENUATOR 4 2 DESCRIPTION OF THE FUNCTIONS

More information

DS1075 EconOscillator/Divider

DS1075 EconOscillator/Divider EconOscillator/Divider www.dalsemi.com FEATURES Dual Fixed frequency outputs (30 KHz - 100 MHz) User-programmable on-chip dividers (from 1-513) User-programmable on-chip prescaler (1, 2, 4) No external

More information

FoxRex 144. RigExpert. Made in the Ukraine. User s manual. ARDF Receiver 144MHz

FoxRex 144. RigExpert. Made in the Ukraine. User s manual. ARDF Receiver 144MHz FoxRex 144 ARDF Receiver 144MHz RigExpert Made in the Ukraine User s manual . Table of contents Introduction Specifications Getting started Charging the battery Switching the receiver on/off Receiver s

More information

Global Navigation Satellite System for IE 5000

Global Navigation Satellite System for IE 5000 Global Navigation Satellite System for IE 5000 Configuring GNSS 2 Information About GNSS 2 Guidelines and Limitations 4 Default Settings 4 Configuring GNSS 5 Configuring GNSS as Time Source for PTP 6 Verifying

More information

Gentec-EO USA. T-RAD-USB Users Manual. T-Rad-USB Operating Instructions /15/2010 Page 1 of 24

Gentec-EO USA. T-RAD-USB Users Manual. T-Rad-USB Operating Instructions /15/2010 Page 1 of 24 Gentec-EO USA T-RAD-USB Users Manual Gentec-EO USA 5825 Jean Road Center Lake Oswego, Oregon, 97035 503-697-1870 voice 503-697-0633 fax 121-201795 11/15/2010 Page 1 of 24 System Overview Welcome to the

More information

Model 25A Manual. Introduction:

Model 25A Manual. Introduction: Model 25A Manual Introduction: The Model 25A drive electronics is a high voltage push-pull linear power amplifier capable of output voltage swings in the order of 145v P-P, push-pull. The Model 25A provides

More information

MFJ ENTERPRISES, INC.

MFJ ENTERPRISES, INC. TM Model MFJ-1924 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551

More information

EE283 Electrical Measurement Laboratory Laboratory Exercise #7: Digital Counter

EE283 Electrical Measurement Laboratory Laboratory Exercise #7: Digital Counter EE283 Electrical Measurement Laboratory Laboratory Exercise #7: al Counter Objectives: 1. To familiarize students with sequential digital circuits. 2. To show how digital devices can be used for measurement

More information

The Amazing MFJ 269 Author Jack Tiley AD7FO

The Amazing MFJ 269 Author Jack Tiley AD7FO The Amazing MFJ 269 Author Jack Tiley AD7FO ARRL Certified Emcomm and license class Instructor, Volunteer Examiner, EWA Technical Coordinator and President of the Inland Empire VHF Club What Can be Measured?

More information

Long Range Wireless OSD 5.8G FPV Transmitter

Long Range Wireless OSD 5.8G FPV Transmitter Long Range Wireless OSD 5.8G FPV Transmitter Built-in 10 Axis AHRS + MAVLINK + 600mW Support all flight controller and GPS 1 / 14 User's Guide Catalogue Product Instruction 3 Features 3 Specifications.4

More information

Grendel Drone Commander CLASSIC PEDAL Analog Music Synthesizer. Rare Waves LLC USA rarewaves.net

Grendel Drone Commander CLASSIC PEDAL Analog Music Synthesizer. Rare Waves LLC USA rarewaves.net CLASSIC PEDAL Analog Music Synthesizer Rare Waves LLC USA rarewaves.net What is it? is a unique synthesizer that delivers thick drone tones with the convenience of an FX pedal stompbox. brings back the

More information

Datasheet of stand-alone GPS smart antenna module, LS20037

Datasheet of stand-alone GPS smart antenna module, LS20037 Product name Description Version LS20037 Stand-alone GPS smart antenna module/mtk,9600bps 0.9 (Preliminary) Datasheet of stand-alone GPS smart antenna module, LS20037 1 Introduction LS20037 is a complete

More information

RigExpert AA-170 Antenna Analyzer (0.1 to 170 MHz) User s manual

RigExpert AA-170 Antenna Analyzer (0.1 to 170 MHz) User s manual RigExpert AA-170 Antenna Analyzer (0.1 to 170 MHz) User s manual Table of contents 1. Description... 3 2. Specifications... 4 3. Precautions... 5 4. Operation... 6 4.1. Preparation for use... 6 4.2. Turning

More information

FCC ID: AXI IC: 10239A Alignment

FCC ID: AXI IC: 10239A Alignment Introduction The VX-261 is carefully aligned at the factory for the specified performance across the frequency range specified for each version. Realignment should therefore not be necessary except in

More information

Analog-to-Digital-Converter User Manual

Analog-to-Digital-Converter User Manual 7070 Analog-to-Digital-Converter User Manual copyright FAST ComTec GmbH Grünwalder Weg 28a, D-82041 Oberhaching Germany Version 2.0, July 7, 2005 Software Warranty FAST ComTec warrants proper operation

More information

Block Diagram. Figure 1. Functional Block Diagram

Block Diagram. Figure 1. Functional Block Diagram MD-171 High Stability GNSS (GPS and GLONASS) Disciplined Oscillator Module MD-171 The MD-171 is a Vectron GNSS disciplined module. It is a fully integrated GNSS disciplined oscillator module in a compact

More information

LBI-30398N. MAINTENANCE MANUAL MHz PHASE LOCK LOOP EXCITER 19D423249G1 & G2 DESCRIPTION TABLE OF CONTENTS. Page. DESCRIPTION...

LBI-30398N. MAINTENANCE MANUAL MHz PHASE LOCK LOOP EXCITER 19D423249G1 & G2 DESCRIPTION TABLE OF CONTENTS. Page. DESCRIPTION... MAINTENANCE MANUAL 138-174 MHz PHASE LOCK LOOP EXCITER 19D423249G1 & G2 LBI-30398N TABLE OF CONTENTS DESCRIPTION...Front Cover CIRCUIT ANALYSIS... 1 MODIFICATION INSTRUCTIONS... 4 PARTS LIST AND PRODUCTION

More information

A NEW GENERATION PROGRAMMABLE PHASE/AMPLITUDE MEASUREMENT RECEIVER

A NEW GENERATION PROGRAMMABLE PHASE/AMPLITUDE MEASUREMENT RECEIVER GENERAL A NEW GENERATION PROGRAMMABLE PHASE/AMPLITUDE MEASUREMENT RECEIVER by Charles H. Currie Scientific-Atlanta, Inc. 3845 Pleasantdale Road Atlanta, Georgia 30340 A new generation programmable, phase-amplitude

More information

Built-in soft-start feature. Up-Slope and Down-Slope. Power-Up safe start feature. Motor will only start if pulse of 1.5ms is detected.

Built-in soft-start feature. Up-Slope and Down-Slope. Power-Up safe start feature. Motor will only start if pulse of 1.5ms is detected. Thank You for purchasing our TRI-Mode programmable DC Motor Controller. Our DC Motor Controller is the most flexible controller you will find. It is user-programmable and covers most applications. This

More information

SL-6 Powering and Wireless System for the 688. User Guide

SL-6 Powering and Wireless System for the 688. User Guide SL-6 Powering and Wireless System for the 688 User Guide Legal Notices Product specifications and features are subject to change without prior notification. Copyright 2015 Sound Devices, C. All rights

More information

Dual 500ns ADC User Manual

Dual 500ns ADC User Manual 7072 Dual 500ns ADC User Manual copyright FAST ComTec GmbH Grünwalder Weg 28a, D-82041 Oberhaching Germany Version 2.3, May 11, 2009 Copyright Information Copyright Information Copyright 2001-2009 FAST

More information

EVDP610 IXDP610 Digital PWM Controller IC Evaluation Board

EVDP610 IXDP610 Digital PWM Controller IC Evaluation Board IXDP610 Digital PWM Controller IC Evaluation Board General Description The IXDP610 Digital Pulse Width Modulator (DPWM) is a programmable CMOS LSI device, which accepts digital pulse width data from a

More information

AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL

AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL Document : AVL-10000T Version: 1.00 Author: Henry S Date: 25 July 2008 This module contains protection circuitry to guard against damage due to

More information

Publication Number ATFxxB Series DDS FUNCTION WAVEFORM GENERATOR. User s Guide

Publication Number ATFxxB Series DDS FUNCTION WAVEFORM GENERATOR. User s Guide Publication Number 101201 ATFxxB Series DDS FUNCTION WAVEFORM GENERATOR User s Guide Introduction This user's guide is used for all models of ATFxxB series of DDS function generator. xx in the model number

More information

EULAMBIA ADVANCED TECHNOLOGIES LTD. User Manual EAT-EOM-CTL-2. Alexandros Fragkos

EULAMBIA ADVANCED TECHNOLOGIES LTD. User Manual EAT-EOM-CTL-2. Alexandros Fragkos EULAMBIA ADVANCED TECHNOLOGIES LTD User Manual Alexandros Fragkos (alexandros.fragkos@eulambia.com) 11/28/2016 28/11/2016 User Manual User Manual 28/11/2016 Electro-Optic Modulator Bias Control Unit v2.0

More information

Using Circuits, Signals and Instruments

Using Circuits, Signals and Instruments Using Circuits, Signals and Instruments To be ignorant of one s ignorance is the malady of the ignorant. A. B. Alcott (1799-1888) Some knowledge of electrical and electronic technology is essential for

More information

1 KW TOTALLY SOLID STATE DIFFERENTIAL GPS TRANSMITTER ( khz)

1 KW TOTALLY SOLID STATE DIFFERENTIAL GPS TRANSMITTER ( khz) GPS1000 1 KW TOTALLY SOLID STATE DIFFERENTIAL GPS TRANSMITTER (282-326 khz) NAUTEL has developed the GPS1000 as an extremely efficient and highly reliable transmitter especially suited for use at remote

More information

QAM Snare Snoop User Manual

QAM Snare Snoop User Manual QAM Snare Snoop User Manual QS-Snoop-v2.0 2/21/2018 This document details the functions and operation of the QAM Snare Snoop leakage detector Table of Contents Overview... 5 Screen Navigation... 6 Settings...

More information

MAINTENANCE MANUAL DIGITAL SELECTOR MODULE 19D902519G1 TABLE OF CONTENTS

MAINTENANCE MANUAL DIGITAL SELECTOR MODULE 19D902519G1 TABLE OF CONTENTS D MAINTENANCE MANUAL DIGITAL SELECTOR MODULE 19D902519G1 TABLE OF CONTENTS Page SPECIFICATIONS...2 CIRCUIT AND FUNCTIONAL DESCRIPTION...3 CONNECTORS AND SYSTEM INTERFACE...4 DIGITAL SELECTOR MODULE AND

More information

Q960 Sequential Controller

Q960 Sequential Controller The Q960 Sequential Controller is a recreation of Bob Moog's famous 960 module. Built using modern components yet retaining the 960's unique functionality including the highly sought-after skip function,

More information

ONCORE ENGINEERING NOTE SL Oncore

ONCORE ENGINEERING NOTE SL Oncore ONCORE ENGINEERING NOTE SL Oncore 1. Product Specifications 2. Basic Description 3. Mechanical 4. Electrical 5. Pin-Out Diagram 6. EMC Considerations 7. RTC (Real Time Clock) 8. 1PPS Signal Description

More information

Dear Valued Customer,

Dear Valued Customer, Dear Valued Customer, Thank you for choosing Listen! All of us at Listen are dedicated to provide you with the highest quality products available. We take great pride in their outstanding performance because

More information

INSTALLATION & OPERATION MANUAL

INSTALLATION & OPERATION MANUAL INSTALLATION & OPERATION MANUAL PREFACE This installation & operation manual is intended as an instruction manual for trained person who is in charge of installation, maintenance, repair, etc. Before installation

More information

STANDARD OPERATING PROCEDURES SOP:: 2057 PAGE: 1 of 6 REV: 0.0 DATE: 07/11/03

STANDARD OPERATING PROCEDURES SOP:: 2057 PAGE: 1 of 6 REV: 0.0 DATE: 07/11/03 PAGE: 1 of 6 1.0 SCOPE AND APPLICATION 2.0 METHOD SUMMARY CONTENTS 3.0 SAMPLE PRESERVATION, CONTAINERS, HANDLING, AND STORAGE 4.0 INTERFERENCES AND POTENTIAL PROBLEMS 5.0 EQUIPMENT/APPARATUS 6.0 REAGENTS

More information

Geotagger N3. User Manual (V1.0) Revised by Geosolve.be (Pol F. Gillard) with personal updates and help. Solmeta Technology Co.

Geotagger N3. User Manual (V1.0) Revised by Geosolve.be (Pol F. Gillard) with personal updates and help. Solmeta Technology Co. Geotagger N3 User Manual (V1.0) Revised by Geosolve.be (Pol F. Gillard) with personal updates and help Solmeta Technology Co., Ltd Copyright 2011 Solmeta Technology Co., Ltd. All Rights Reserved 1 Contents

More information

16-Bit ANALOG-TO-DIGITAL CONVERTER

16-Bit ANALOG-TO-DIGITAL CONVERTER 16-Bit ANALOG-TO-DIGITAL CONVERTER FEATURES 16-BIT RESOLUTION LINEARITY ERROR: ±0.003% max (KG, BG) NO MISSING CODES GUARANTEED FROM 25 C TO 85 C 17µs CONVERSION TIME (16-Bit) SERIAL AND PARALLEL OUTPUTS

More information

Costas Loop. Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier

Costas Loop. Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier Costas Loop Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier 0 Pre-Laboratory Reading Phase-shift keying that employs two discrete

More information

Connevans. DeafEquipment.co.uk. This product may be purchased from Connevans Limited secure online store at

Connevans. DeafEquipment.co.uk. This product may be purchased from Connevans Limited secure online store at Connevans Solutions to improve the quality of life This product may be purchased from Connevans Limited secure online store at www.deafequipment.co.uk DeafEquipment.co.uk Solutions to improve the quality

More information

6688 OCXO Frequency Reference 6689 Rubidium Frequency Reference. User's Manual

6688 OCXO Frequency Reference 6689 Rubidium Frequency Reference. User's Manual 6688 OCXO Frequency Reference 6689 Rubidium Frequency Reference User's Manual 6688 OCXO Frequency Reference 6689 Rubidium Frequency Reference Operators manual 2017, Pendulum Instruments / Altaria Services

More information

LM2240 Programmable Timer Counter

LM2240 Programmable Timer Counter LM2240 Programmable Timer Counter General Description The LM2240 Programmable Timer Counter is a monolithic controller capable of both monostable and astable operation Monostable operation allows accurate

More information

ERICSSONZ LBI-30398P. MAINTENANCE MANUAL MHz PHASE LOCKED LOOP EXCITER 19D423249G1 & G2 DESCRIPTION TABLE OF CONTENTS

ERICSSONZ LBI-30398P. MAINTENANCE MANUAL MHz PHASE LOCKED LOOP EXCITER 19D423249G1 & G2 DESCRIPTION TABLE OF CONTENTS MAINTENANCE MANUAL 138-174 MHz PHASE LOCKED LOOP EXCITER 19D423249G1 & G2 TABLE OF CONTENTS Page DESCRIPTION... Front Cover CIRCUIT ANALYSIS...1 MODIFICATION INSTRUCTIONS...4 PARTS LIST...5 PRODUCTION

More information