DATA SHEET LG-110RBG-DT/T15-3T1-B01 發行 立碁電子 DCC LED SMD. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only

Transcription

1 LED SMD Pb L-110-DT/T15-3T1-01 DATA SHEET DOC. NO : QW0905-L-110-DT/T15-3T1-01 EV. : DATE : 15 - Mar 發行 立碁電子 DCC

2 PAT NO. L-110-DT/T15-3T1-01 Page 1/14 Features: 1. Package in 8.0mm carrier tape on 7" diameter reel. 2. Compatible with automatic placement equipment. 3. Compatible with reflow solder process. Descriptions: 1. The L-110 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. 2. esides, lightweight makes them ideal for miniature applications. etc. Applications: 1. Automotive : backlighting in dashboard and switch. 2. Telecommunication : indicator and backlighting in telephone and fax. 3. Flat backlight for LCD, switch and symbol 4. eneral use. Device Selection uide: PAT NO MATEIAL Emitted COLO Lens AlaInP ed L-110-DT/T15-3T1-01 lnan lue White Diffused lnan reen

3 PAT NO. L-110-DT/T15-3T1-01 Page 2/14 Package Dimensions 4 3 esin PC Note : 1.All dimension are in millimeter tolerance is 0.1mm unless otherwise noted. 2.Specifications are subject to change without notice. ecommended Soldering Pad Dimensions Note : The tolerances unless mentioned is 0.1mm,Angle. Unit=mm.

4 PAT NO. L-110-DT/T15-3T1-01 Page 3/14 Absolute Maximum atings at Ta=25 Parameter Symbol atings UNIT Power Dissipation PD mw Peak Forward Current Duty IFP ma Forward Current IF ma everse Ir A Electrostatic Discharge ESD V Operating Temperature Topr -40 ~ + 85 Storage Temperature Tstg -40 ~ + 100

5 PAT NO. L-110-DT/T15-3T1-01 Page 4/14 Typical Electrical & Optical Characteristics (Ta=25 ) Items Symbol Min. Typ. Max. UNIT CONDITION Luminous Intensity Iv mcd IF=15mA Dominant Wavelength D nm IF=15mA Spectral Line Half-Width nm IF=15mA Forward Voltage VF V IF=15mA Viewing Angle 2 1/ deg IF=15mA

6 PAT NO. L-110-DT/T15-3T1-01 Luminous Intensity Classification Iv(mcd) at 15mA IN CODE Min. Max. S T U Iv(mcd) at 15mA IN CODE Min. Max. Q Iv(mcd) at 15mA IN CODE Min. Max. U V V Forward Voltage Classification Vf(v) at 15mA IN CODE Min. Max Vf(v) at 15mA IN CODE Min. Max Vf(v) at 15mA IN CODE Min. Max Page 5/14

7 Typical Electro-Optical Characteristics Curve LIITEK ELECTONICS CO.,LTD. PAT NO. L-110-DT/T15-3T1-01 Page 6/14 CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Luminous Intensity vs. Forward Current Luminous Intensity Forward Voltage(V) Fig.3 Forward Current vs. Temperature Fig.4 Luminous Intensity vs. Temperature Ambient Temperature (Ta C) Luminous Intensity(%)@20mA Ambient Temperature( ) Fig.5 elative Intensity vs. Wavelength Fig.6 Directive adiation elative Intensity@20mA % 75% 50% 25% 0 25% % 75% 100% Wavelength (nm)

8 PAT NO. L-110-DT/T15-3T1-01 Page 7/14 Typical Electro-Optical Characteristics Curve CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 elative Intensity vs. Forward Current elative Intensity Forward Voltage(V) Fig.3 Forward Current vs. Temperature Fig.4 elative Intensity vs. Temperature elative Intensity@15mA Ambient Temperature (Ta C) Ambient Temperature( ) Fig.5 elative Intensity vs. Wavelength Fig.6 Directive adiation elative Intensity@15mA % 75% 50% 25% 0 25% % 75% 100% Wavelength (nm)

9 PAT NO. L-110-DT/T15-3T1-01 Page 8/14 Typical Electro-Optical Characteristics Curve CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 elative Intensity vs. Forward Current elative Intensity Forward Voltage(V) Fig.3 Forward Current vs. Temperature Fig.4 elative Intensity vs. Temperature elative Intensity@15mA Ambient Temperature (Ta C) Ambient Temperature( ) Fig.5 elative Intensity vs. Wavelength Fig.6 Directive adiation elative Intensity@15mA % 75% 50% 25% 0 25% % 75% 100% Wavelength (nm)

10 PAT NO. L-110-DT/T15-3T1-01 Page 9/14 Carrier Type Dimensions ± ± ± ± Note : The tolerances unless mentioned is 0.1mm,Angle. Unit=mm. Packing Specifications Label Aluminum Moist-Proof bag Label Part No. L-110-DT/T15-3T1-01 Description 8.0mm tape,7"reel Quantity/eel 3000 devices

11 13.5 LIITEK ELECTONICS CO.,LTD. PAT NO. L-110-DT/T15-3T1-01 Page 10/14 Label Explanation Pb LIITEK ELECTONICS CO., LTD. IN : Luminous Intensity VF : Forward Voltage eel Dimensions

12 PAT NO. L-110-DT/T15-3T1-01 Page 11/14 ox Explanation 1. 5 A / INNE OX 2. INNE OX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L INNE OXES / CATON 4. CATON SIZE : L X W X H 58cm X 34cm x 35cm L W H

13 ecommended Soldering Conditions LIITEK ELECTONICS CO.,LTD. PAT NO. L-110-DT/T15-3T1-01 Page 12/14 1. Hand Solder asic spec is 280 C 3 sec one time only. 2 P-Free eflow Solder 1~5 C/sec 260 C MaX. 10sec.Max 1~5 C/sec Preheat 180~200 C Above 220 C 60 sec.max. 6 C/sec 120 sec.max. Note: 1.eflow soldering should not be done more than two times. 2.When soldering,do not put stress on the LEDs during heating. 3.After soldering,do not warp the circuit board.

14 PAT NO. L-110-DT/T15-3T1-01 Page 13/14 Precautions For Use: Storage time: 1. Calculated shelf life before opening is 18 months at < 30 C and < 90% relative humidity (H) 2. After bag is opened, devices which will be subjected to reflow soldering or other high temperature processes must be a) Assemblied within one years in an environment of 30 C / 60% H, or b) Stored at ambient of 10% H or less 3. Devices are required baking before assembly if: a) Humidity Indicator Card reads >10% (for level 2a -5a) or >60% (for level 2) at ambient temperature 23 5 C b) 2.a) or 2.b) doesn't meet 4. If baking is required, devices should be baked for >72 hours at 60±5 C/ 5% H.Performing baking only once, and using the baked devices within 72 hours.. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A LED Circuit model LED (A) ecommended circuit. () The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded.

15 PAT NO. L-110-DT/T15-3T1-01 Page 14/14 eliability Test: Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=25 C 2.If=15mA 3.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature Storage Test 1.Ta=100 C±5 C 2.t=1000 hrs (-24hrs,+72hrs) 22 Endurance Test Low Temperature Storage Test 1.Ta=-40 C±5 C 2.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature High Humidity Storage Test 1.Ta=85 C 2.H=85% 3.t=1000hrs(-24hrs,+72hrs) 22 Thermal Shock Test 1.Ta=100 C±5 C ~ -40 C±5 C 20min/ 10sec / 20min 2.total 100 cycles 22 Environmental Test Temperature Cycling C±5 C -40 C±5 C 30mins / 5mins / 30mins Cyeles 22 I eflow 1.T=260 C Max. 10sec.Max Min 22