Recommended Minimum Performance Standards for Simultaneous cdma2000 1x and cdma2000 HRPD Access Terminal

Transcription

1 GPP C.S00-A Version.0 July 0 Recommended Minimum Performance Standards for Simultaneous cdma000 x and cdma000 HRPD Access Terminal 0 GPP GPP and its Organizational Partners claim copyright in this document and individual Organizational Partners may copyright and issue documents or standards publications in individual Organizational Partner's name based on this document. Requests for reproduction of this document should be directed to the GPP Secretariat at secretariat@gpp.org. Requests to reproduce individual Organizational Partner's documents should be directed to that Organizational Partner. See for more information.

2 Revision History Revision Description of Changes Date Rev 0 v.0 Initial publication January 0 Rev A v.0 Added Japan Radio Law related changes, including BC emission, BC disband, and BC0 subclasses, April 0 Rev A v.0 Bug fixes. March 0 Rev A v.0 Republication to fix missing reference July 0

3 CONTENTS Foreword... ix Notes... xi Introduction Scope Requirements Terminology Terms and Definitions CDMA and HRPD Equations Tolerances CDMA and HRPD System Parameter Tolerances Measurement Tolerances References... - Standard Radiated Emissions Measurement Procedure Standard Radiation Test Site Search Antenna Field-Strength Measurement Frequency Range of Measurements Test Ranges Meter Test Range Meter Test Range Radiated Signal Measurement Procedures... - Physical Layer Receiver Minimum Standards Demodulation Requirements for SB-CDMA-HRPD Demodulation of Forward Traffic Channel in AWGN Definition Method of Measurement Minimum Standard for HRPD Minimum Standard for CDMA Demodulation Requirements for DB-CDMA-HRPD Demodulation of Forward Traffic Channel in AWGN Definition... - i

4 Method of Measurement Minimum Standard for HRPD Minimum Standard for CDMA Receiver Performance for SB-CDMA-HRPD Receiver Sensitivity and Dynamic Range Definition Method of Measurement Minimum Standard Single Tone Desensitization Definition Method of Measurement Minimum Standard Receiver Performance for DB-CDMA-HRPD Receiver Sensitivity and Dynamic Range Definition Method of measurement Minimum Standard Single Tone Desensitization Definition Method of Measurement Minimum Standard... - Physical Layer Transmitter Minimum Standards Modulation Requirements for SB-CDMA-HRPD Waveform Quality and Frequency Accuracy Definition Method of Measurement Minimum Standard Modulation Requirements for DB-CDMA-HRPD Waveform Quality and Frequency Accuracy Definition Method of Measurement Minimum Standard... - ii

5 RF Output Power Requirements for SB-CDMA-HRPD Maximum RF Output Power Definition Method of Measurement Minimum Standard RF Output Power Requirements for DB-CDMA-HRPD Maximum RF Output Power Definition Method of Measurement Minimum Standard Limitations on Emissions for SB-CDMA-HRPD Conducted Spurious Emissions Definition Method of Measurement Minimum Standard Occupied Bandwidth Definition Method of Measurement Minimum Standard Limitations on Emissions for DB-CDMA-HRPD Conducted Spurious Emissions Definition Method of Measurement Minimum Standard Occupied Bandwidth Definition Method of Measurement Minimum Standard... - Environmental Requirements Temperature and Power Supply Voltage Definition Method of Measurement... - iii

6 0 0.. Minimum Standard High Humidity Definition Method of Measurement Minimum Standard Vibration Stability Definition Method of Measurement Minimum Standard Shock Stability Definition Method of Measurement Minimum Standard... - Standard Test Conditions... - Annex A Selected Performance Requirements Tables (Normative)... A- A. Demodulation Requirements for HRPD... A- A.. Demodulation of Forward Traffic Channel in AWGN... A- A... Method of Measurement... A- A... Minimum Standard for HRPD in SB-CDMA-HRPD... A- A... Minimum Standard for HRPD in DB-CDMA-HRPD... A- A. CDMA Forward Traffic Channel Demodulation Performance Tables... A- A.. Forward Traffic Channel Performance Requirements in AWGN... A- A... Method of Measurement Test Parameters... A- A... Minimum Standards Requirements... A- iv

7 0 0 0 TABLES Table...-. Test Parameters for Receiver Sensitivity (Test ) and Dynamic Range (Test )... - Table...-. Test Parameters for Single Tone Desensitization for CDMA-HRPD operation Table...-. Minimum Effective Radiated Power for Single Tone Desensitization Test for Band Class Table...-. Test Parameters for Receiver Sensitivity (Test ) and Dynamic Range (Tests, )... - Table...-. Test Parameters for Receiver Sensitivity (Test ) and Dynamic Range (Test )... - Table...-. Test Parameters for CDMA carrier Single Tone Desensitization in B... - Table...-. Minimum Effective Radiated Power for CDMA carrier Single Tone Desensitization Test for B = Band Class and for HRPD carrier Single Tone Desensitization Test for B = Band Class Table...-. Test Parameters for HRPD carrier Single Tone Desensitization in B Table...-. Test Parameters for HRPD carrier Single Tone Desensitization for Multicarrier HRPD Operation (Subtype Physical Layer)... - Table...-. Test Parameters for Maximum RF Output Power with a Single Traffic Code Channel, Spreading Rate... - Table...-. Effective Radiated Power at Maximum Output Power... - Table...-. Test Parameters for CDMA channel... - Table...-. Effective Radiated Power at Maximum Output Power... - Table...-. Test Parameters for Testing Spurious Emissions with a Single Traffic Code Channel at Maximum RF Output Power... - Table...-. Band Classes 0,,,,,, 0,, and Transmitter Spurious Emission Limits for Test... - Table...-. Band Classes,,, and Transmitter Spurious Emission Limits for Test... - Table...-. Adjacent Multi-carrier Transmitter Spurious Emission Limits for Number of adjacent reverse CDMA channels, N =... - Table...-. Adjacent Multi-carrier Transmitter Spurious Emission Limits for Number of adjacent reverse CDMA channels, N... - Table...-. Test Parameters for Testing Occupied Bandwidth at Maximum RF Output Power... - Table...-. Test Parameters for CDMA channel... - v

8 0 0 0 Table...-. Band Classes 0,,,,, 0,, and Transmitter Spurious Emission Limits... - Table...-. Band Classes,,, and Transmitter Spurious Emission Limits - Table...-. Band Class Transmitter Spurious Emission Limits... - Table...-. Additional Band Class Transmitter Spurious Emission Limits... - Table...-. Additional Band Class and Transmitter Spurious Emission Limits - Table...-. Additional Band Class Transmitter Spurious Emission Limits... - Table...-. Band Classes 0,,,,,, 0,, and Transmitter Spurious Emission Limits... - Table...-. Band Classes,,, and Transmitter Spurious Emission Limits Table...-. Adjacent Multi-carrier Transmitter Spurious Emission Limits for Number of adjacent reverse CDMA channels, N =... - Table Adjacent Multi-carrier Transmitter Spurious Emission Limits for Number of adjacent reverse CDMA channels, N... - Table...-. Test Parameters for Testing Occupied Bandwidth at Maximum RF Output Power... - Table..-. Temperature Ranges... - Table A...-. Test Parameters for FTC Demodulation in AWGN (Part of )... A- Table A...-. Test Parameters for FTC Demodulation in AWGN (Part of )... A- Table A...- Test Parameters for FTC Demodulation in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- vi

9 Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN (Part of )... A- Table A...-. Minimum Standards for Forward Traffic Channel Performance in AWGN(Part of )... A- vii

10 This page intentionally left blank. viii

11 FOREWORD (This foreword is not part of this Standard) This Standard was prepared by Technical Specification Group C of the Third Generation Partnership Project (GPP). This Standard contains recommended minimum performance standards for Simultaneous cdma000 and cdma000-hrpd Access Terminal. cdma000 is the trademark for the technical nomenclature for certain specifications and standards of the Organizational Partners (OPs) of GPP. Geographically (and as of the date of publication), cdma000 is a registered trademark of the Telecommunications Industry Association (TIA-USA) in the United States ix

12 This page intentionally left blank. x

13 NOTES. Mobile station and Access terminal are used interchangeably in this document.. Throughput this document, cdma000 x is called CDMA, and cdma000 HRPD is called HRPD.. An simultaneous cdma000 and cdma000 HRPD capable access terminal is one that is capable of supporting calls on a CDMA and one or more HRPD carriers at the same time. Such capability is denoted as CDMA-HRPD in this Standard. A singleband CDMA-HRPD capable (SB-CDMA-HRPD) access terminal is one that can support simultaneous calls on a CDMA and one or more HRPD carriers when the CDMA and HRPD carriers belong to the same band class. A dual-band CDMA-HRPD capable (DB-CDMA-HRPD) access terminal is one that can support simultaneous calls on a CDMA and one or more HRPD carriers when the carriers belong to two different band classes.. To ensure that the tests accurately represent CDMA-HRPD performance, the tester should start collecting minimum performance data for CDMA-HRPD only after both CDMA and HRPD calls have been established. This is true for all tests that require simultaneous CDMA and HRPD calls.. The term Band Class Combination is used in the context of dual-band CDMA_HRPD. A band class combination is a pair of band classes on which a mobile station can operate a CDMA carrier and one or more HRPD carriers simultaneously. The band class combination lists the CDMA band class first, followed by the HRPD band class. For example, for a mobile station supporting a CDMA carrier on Band Class A and a HRPD carrier on Band Class B, the band class combination would be designated as Band Class A, Band Class B.. Base station refers to the functions performed on the land side, which are typically distributed among a cell, a sector of a cell, and a mobile communications switching center.. Access network refers to the network equipment providing data connectivity between a packet switched data network (typically the Internet) and the access terminals. Connectivity is typically provided at the Link Layer (PPP).. Sector refers to the part of the access network that provides the land-side modem.. This standard uses the following verbal forms: Shall and shall not identify requirements to be followed strictly to conform to the standard and from which no deviation is permitted. Should and should not indicate that one of several possibilities is recommended as particularly suitable, without mentioning or excluding others; that a certain course of action is preferred but not necessarily required; or that (in the negative form) a certain possibility or course of action is discouraged but not prohibited. May and need not indicate a course of action permissible within the limits of the standard. Can and cannot are used for statements of possibility and capability, whether material, physical, or causal. 0. Unless indicated otherwise, this document presents numbers in decimal form. Binary numbers are distinguished in the text by the use of single quotation marks. xi

14 Those wishing to deploy systems compliant with this standard should also be compliant with local radio regulations. For example, operation within the United States of America shall comply with Parts,,,, and of [] and with the applicable rules and regulations of local administrations.. The following operators define mathematical operations: indicates multiplication. / indicates division. + indicates addition. - indicates subtraction. * indicates complex conjugation. indicates a member of the set. x indicates the largest integer less than or equal to x:. =,.0 =. x indicates the absolute value of x: - =, =.. All Radio Configuration Eb/Nt requirements for Band Class 0 in this document are based on measured data. For all other band classes, the radio configuration Eb/Nt requirements in this document are based on simulated data with standard margins of. db for static and. db for fading channel cases. Additional Forward Fundamental Channel rate determination margins of 0., 0., and 0. db are added for the /, /, and / rate cases, respectively.. Tests in this revision reference the General Neighbor List Message, Universal Neighbor List Message and the Universal Handoff Direction Message to maintain consistency with new tests that require the extended capability of these messages. Where needed to test a P_REV six or lower mobile station, the Neighbor List Message, Extended Neighbor List Message, and Extended Handoff Direction Message may be used as specified in [].. Some tests may specify using the Paging Channel for general test setup requirements. If the mobile station does not support the Paging Channel, then the Broadcast Control Channel and Forward Common Control Channel shall be used in lieu of the Paging Channel.. The Standard applies only to Band Classes 0,, (Band Subclasses 0,, and ),,, (Band Subclasses 0 through ),,,,, 0 (Band Subclasses 0 through ), (Band Subclasses 0 through ), and (Band Subclasses 0 and ) as defined in []. Operation with other band classes and band subclasses may not be supported by this Standard. xii

15 INTRODUCTION. Scope This Standard details definitions, methods of measurement, and minimum performance characteristics for CDMA-HRPD-capable access terminals. An CDMA-HRPD-capable access terminal shall satisfy the requirements of this document in addition to satisfying those in [] and []. A single-band CDMA-HRPD (SB-CDMA-HRPD) access terminal shall pass all SB-CDMA-HRPD MPS tests in this document. A dual-band CDMA-HRPD (DB- CDMA-HRPD) access terminal that also supports SB-CDMA-HRPD shall pass the SB- CDMA-HRPD MPS tests in each individual band class in addition to passing the DB- CDMA-HRPD MPS tests in this document. The purpose of this standard is to ensure that an CDMA-HRPD-capable access terminal can obtain service in any system that meets the compatibility requirements of [] and []. Compatibility, as used in connection with this Standard and [] and [], is understood to mean that any CDMA-HRPD-capable access terminal is able to simultaneously open data connections in any HRPD system and place and receive calls in any CDMA system. Conversely, all HRPD systems are able to open connections and all CDMA systems are able to place and receive calls simultaneously with any CDMA-HRPD-capable access terminal. Test methods are recommended in this document; however, methods other than those recommended may suffice for the same purpose. The performance metrics in this Standard require an access terminal to provide a single antenna connector for testing. Access terminals having multiple antenna, such as for receive diversity, shall provide a single antenna connector for testing. If an access terminal has more than one antenna connector, only one connector shall be used for testing. Additional requirements specifically for multiple antenna configurations, i.e. receive diversity, are for future study... Requirements Terminology Shall and shall not identify requirements to be followed strictly to conform to this document and from which no deviation is permitted. Should and should not indicate that one of several possibilities is recommended as particularly suitable, without mentioning or excluding others, that a certain course of action is preferred but not necessarily required, or that (in the negative form) a certain possibility or course of action is discouraged but not prohibited. May and need not indicate a course of action permissible within the limits of the document. Can and cannot are used for statements of possibility and capability, whether material, physical or causal.. Terms and Definitions Since CDMA-HRPD consists of simultaneous CDMA and HRPD calls, the terms and definitions used in this document are the same as those of the respective technologies. These terms and definitions are listed in Section. of the most recent revision and version of [] (for CDMA) and [] (for HRPD). -

16 0 0 The test modes and the mapping to radio configurations for CDMA are described in Section. of [].. CDMA and HRPD Equations Sections. of [] and. of [] list the equations that describe the relationship between various test parameters under different conditions for CDMA and HRPD respectively.. Tolerances.. CDMA and HRPD System Parameter Tolerances CDMA parameters are specified in []. HRPD parameters are specified in []. All parameters indicated in all sections are exact unless an explicit tolerance is stated... Measurement Tolerances Unless otherwise specified, a measurement tolerance, including the tolerance of the measurement equipment, of ±0% is assumed. Unless otherwise specified, the Î or/ioc value shall be within ±0. db of the value specified, and the I oc value shall be within ± db of the value specified.. References NORMATIVE REFERENCES The following standards contain provisions that, through reference in this text, constitute provisions of this Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI and TIA maintain registers of currently valid national standards published by them. 0 [] GPP C.S00-00-C v.0, cdma000 High Rate Packet Data Air Interface Specification, December 0. [] GPP C.S00-D v.0, Recommended Minimum Performance Standards for cdma000 High Rate Packet Data Access Network, March 0. [] GPP C.S00-B v.0, Test Application Specification for cdma000 High Rate Packet Data Air Interface, March 00. [] GPP C.S00-E v.0, Recommended Minimum Performance Standards for cdma000 Spread Spectrum Mobile Stations, March 0. [] IEEE C.-00, American National Standard for Methods of Measurement of Radio Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of khz to 0 GHz, 00. [] CFR Title, Code of Federal Regulations. -

17 0 0 [] GPP C.S00-E v.0, Band Class Specification for cdma000 Spread Spectrum Systems, October 00. [] GPP C.S000-F v.0, Physical Layer Standard for cdma000 Spread Spectrum Systems, December 0. [] Reserved. [0] GPP C.S000-F v.0, Signaling Link Access Control (LAC) Standard for cdma000 Spread Spectrum Systems, December 0. [] GPP C.S000-F v.0, Upper Layer (Layer ) Signaling Standard for cdma000 Spread Spectrum Systems, December 0. [] GPP C.S000-E v.0, Recommended Minimum Performance Standards for cdma000 Spread Spectrum Base Stations, March 0. [] GPP C.S00-A v.0, Test Data Service Option (TDSO) for cdma000 Spread Spectrum Systems, Feburary 00. [] GPP C.S00-A v.0, Markov Service Option (MSO) for cdma000 Spread Spectrum Systems, June 0. [] GPP C.S00-B v.0, Loopback Service Options (LSO) for cdma000 Spread Spectrum Systems, January 0. [] GPP C.S000-F v.0, Medium Access Control (MAC) Standard for cdma000 Spread Spectrum Systems, December 0. [] GPP C.S00-D v.0, Recommended Minimum Performance Standards for cdma000 High Rate Packet Data Access Terminal, March 0. [] GPP TS.00, Modulation. [] GPP C.S00-00-C v.0, Connection and Security Layers for cdma000 High Rate Packet Data Air Interface Specification, July 0. -

18 This page intentionally left blank. -

19 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE The measurement and calibration procedures described are intended to provide an overview of radiated and conducted signal measurements. A detailed description of the required measurement procedures is given in [].. Standard Radiation Test Site The test site shall be on level ground that is of uniform electrical characteristics. The site shall be clear of overhead wires and other metallic objects and shall be as free as possible from undesired signals, such as ignition noise and other carriers. Reflecting objects, such as rain gutters and power cables shall lie outside an ellipse measuring 0 meters on the major axis by meters on the minor axis for a 0-meter site, or an ellipse measuring meters on the major axis by. meters on the minor axis for a -meter site. The equipment under test shall be located at one focus of the ellipse and the measuring antenna at the other focus. If desired, shelters may be provided at the test site to protect the equipment and personnel. All such construction shall be of wood, plastic, or other non-metallic material. All power, telephone, and control circuits to the site shall be buried at least 0. meter under ground. A turntable, essentially flush with the ground, shall be provided that can be remotely controlled. A platform. meters high shall be provided on this turntable to hold the equipment under test. Any power and control cables that are used for this equipment should extend down to the turntable, and any excess cabling should be coiled on the turntable. If the equipment to be tested is mounted in racks and is not easily removed for testing on the above platform, then the manufacturer may elect to test the equipment when it is mounted in its rack (or racks). In this case, the rack (or racks) may be placed directly on the turntable. If a transmitter with an external antenna connection is being tested, then the RF output of this transmitter shall be terminated in a non-radiating load that is placed on the turntable. A non-radiating load is used in lieu of an antenna to avoid interference with other radio users. The RF cable to this load should be of minimum length. The transmitter shall be tuned and adjusted to its rated output value before starting the tests. In order to conduct unintentional radiator tests as specified in Part, subpart B of [], the radiation site must comply with.. through. of [] as required by Part. of [].. Search Antenna For narrow-band dipole adjustable search antennas, the dipole length shall be adjusted for each measurement frequency. This length may be determined from a calibration ruler that is normally supplied with the equipment. The search antenna shall be mounted on a movable non-metallic horizontal boom that can be raised or lowered on a wooden or other non-metallic pole. The cable connected to the search antenna shall be at a right angle to the antenna. The cable shall be dressed at least meters, either through or along the horizontal boom, in a direction away from the -

20 0 0 0 equipment being measured. The search antenna cable may then be dropped from the end of the horizontal boom to ground level for connection to the field-strength measuring equipment. The search antenna shall be capable of being rotated 0 degrees on the end of the horizontal boom to allow measurement of both vertically and horizontally polarized signals. When the antenna length of a vertically mounted antenna does not permit the horizontal boom to be lowered to its minimum specified search range, adjust the minimum height of the boom for 0. meter clearance between the end of the antenna and the ground.. Field-Strength Measurement A field-strength meter shall be connected to a search antenna. The field-strength meter shall have sufficient sensitivity and selectivity to measure signals over the required frequency ranges at levels at least 0 db below the levels specified in any document, standard, or specification that references this measurement procedure. The calibration of the measurement instruments (field-strength meter, antennas, etc.) shall be checked frequently to ensure that their accuracy is in accordance with the current standards. Such calibration checks shall be performed at least once per year.. Frequency Range of Measurements When measuring radiated signals from transmitting equipment, the measurements shall be made from the lowest radio frequency (but no lower than MHz) generated in the equipment to the tenth harmonic of the carrier, except for that region close to the carrier equal to ±0% of the authorized bandwidth. When measuring radiated signals from receiving equipment, the measurements shall be made from MHz to at least GHz.. Test Ranges.. 0-Meter Test Range Measurement of radiated signals shall be made at a point 0 meters from the center of the turntable. The search antenna shall be raised and lowered from to meters in both horizontally and vertically polarized orientations. The field-strength measuring meter may be placed on a suitable table or tripod at the foot of the mast. When measuring radiated emissions from receivers, equipment that contains its own receive antenna shall be tested with the antenna in place. Equipment that is connected to an external receive antenna via a cable shall be tested without the antenna, and the receive ports on the equipment under test shall be terminated in a 0 non-radiating resistive load... -Meter Test Range Measurement of radiated signals may be made at a point meters from the center of the turntable, provided the following three conditions can be met: -

21 A ground screen that covers an elliptical area at least meters on the major axis by. meters on the minor axis is used with the measuring antenna and turntable mounted meters apart. The measuring antenna and turntable shall lie on the major axis and shall be equidistant from the minor axis of the elliptical area.. The maximum dimension of the equipment shall be meters or less. When measuring radiated signals from receivers, the maximum dimension shall include the antenna if it is an integral part of the device.. The field-strength measuring equipment is either mounted below the ground level at the test site or is located a sufficient distance away from the equipment being tested and from the search antenna to prevent corruption of the measured data. The search antenna shall be raised and lowered over a range from to meters in both horizontally and vertically polarized orientations. When the search antenna is vertically oriented, the minimum height of the center of the search antenna shall be defined by the length of the lower half of the search antenna. When measuring radiated emissions from receivers, equipment that contains its own receive antenna shall be tested with the antenna in place. Equipment that is connected to an external receive antenna via a cable shall be tested without the antenna, and the receive ports on the equipment under test shall be terminated in a 0 non-radiating resistive load. The -meter test range may be used for determining compliance with limits specified at 0 meters (or other distances), provided that:. The ground reflection variations between the two distances have been calibrated for the frequencies of interest at the test range, or. A db correction factor is added to the specified radiation limit(s) to allow for average ground reflections. Radiated field strength (volts/meter) varies inversely with distance, so that a measurement made on the -meter test range divided by 0 gives the equivalent value that would be measured on a 0-meter test range for the same EIRP (effective isotropic radiated power). The 0-meter field strength in volts/meter can be calculated from the EIRP by using the following formula: EIRP(dBm)/0 meters Radiated Signal Measurement Procedures Radiated signals having significant levels shall be measured on the 0-meter or the -meter range by using the following procedure:. For each observed radiated signal, raise and lower the search antenna to obtain a maximum reading on the field-strength meter with the antenna horizontally polarized. Then rotate the turntable to maximize the reading. Repeat this procedure of raising and lowering the antenna and rotating the turntable until the highest possible signal has been obtained. Record this maximum reading.. Repeat step for each observed radiated signal with the antenna vertically polarized. -

22 0. Remove the equipment being tested and replace it with a half-wave antenna. The center of the half-wave antenna should be at the same approximate location as the center of the equipment being tested.. Feed the half-wave antenna replacing the equipment under test with a signal generator connected to the antenna by means of a non-radiating cable. With the antennas at both ends horizontally polarized and with the signal generator tuned to the observed radiated signal, raise and lower the search antenna to obtain a maximum reading on the field-strength measuring meter. Adjust the level of the signal generator output until the previously recorded maximum reading for this set of conditions is obtained. Record the signal generator power output.. Repeat step above with both antennas vertically polarized.. Calculate the power into a reference ideal isotropic antenna by: a. First reducing the readings obtained in steps and above by the power loss in the cable between the generator and the source antenna, and b. Then correcting for the gain of the source antenna used relative to an ideal isotropic antenna. The reading thus obtained is the equivalent effective isotropic radiated power (EIRP) level for the spurious signal being measured.. Repeat steps through above for all observed signals from the equipment being tested. -

23 0 0 0 PHYSICAL LAYER RECEIVER MINIMUM STANDARDS. Demodulation Requirements for SB-CDMA-HRPD.. Demodulation of Forward Traffic Channel in AWGN On the CDMA carrier, this test shall be performed on the Forward Fundamental Channel, if the Forward Fundamental Channel is supported by the mobile station. Forward Traffic Channel closed loop power control in the CDMA base station shall be disabled during this test.... Definition The performance of the demodulation of Forward Traffic Channel in an AWGN (no fading or multipath) environment is determined by the frame error rate (FER) for the CDMA channel and packet error rate (PER) for the HRPD channel. The PER and FER are calculated for each individual data rate and on a per carrier basis. For CDMA Radio Configuration Fundamental Channel, the accuracy of the Erasure Indicator bits sent by the mobile station is verified in this test.... Method of Measurement. Connect the sectors and the AWGN generator to the access terminal antenna connector as shown in Figure..- of [] (Figure..- of []).. For each band class that the access terminal supports, configure the access terminal to operate in that band class. Configure the access terminal to transmit on one CDMA and one HRPD channel at maximum separation supported by the device. The maximum carrier separation should be at least. MHz. Perform steps through.. For each CDMA radio configuration supported on the Forward Fundamental Channel, set up a CDMA call using Fundamental Channel (see. of []) with frame activity equal to 00%.. For HRPD, perform steps and. For Subtype 0 to Physical Layer tests, perform steps through. For Subtype or Physical Layer tests, perform steps and.. Set the access network's forward HRPD packet activity to 00%. If the data rate under test is. Mbps or higher, an access network simulator meeting the waveform quality requirements in.. of [] shall be used. Set the access network s Control Channel data rate to. kbps. To ensure that the tests accurately represent CDMA-HRPD performance, the tester should start collecting PER and FER data only after both CDMA and HRPD calls have been established. -

24 . Set the HRPD SetManagementSameChannelParameters attribute fields of the Default Route Update Protocol to the values specified below: PilotDrop Field Value (Hex) 0xc (- db) Set up a HRPD Test Application session. Open a connection and configure the Test Application FTAP (for Subtype 0 or Physical Layer) so that the HRPD Forward Traffic Channel rate corresponds to the rate of the test only.. Set the test parameters for each HRPD demodulation test specified in Table A From the number of HRPD packets transmitted and the number of bad packets received, calculate the PER for this test. Unless otherwise specified, the PER shall be measured at the end of the packet. 0. Set the test parameters for each CDMA demodulation test as specified in Table A...- through Table A Count, at the base station, the number of CDMA frames transmitted and the number of good frames received at the mobile station.. For CDMA Radio Configuration, check the accuracy of the received Erasure Indicator bits at the base station against the corresponding frames received at the mobile station.. If the access terminal supports HRPD Subtype or Subtype Physical Layer, set up a HRPD Test Application session. Open a connection and configure the Test Application FETAP (for Subtype or Physical Layer) so that the HRPD Forward Traffic Channel rate corresponds to the rate of the test only.. Set the test parameters for each HRPD demodulation test specified in Table A...- and repeat step.... Minimum Standard for HRPD The actual E b /N t used in each test shall be within ±0. db of the value indicated in Table A...- through Table A...-. For access terminals that support HRPD Subtype 0 or Subtype Physical Layer, the PER shall not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. The PER should not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. For access terminals that support HRPD Subtype or Subtype Physical Layer, the PER shall not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. The PER should not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. -

25 Minimum Standard for CDMA The actual power measurement uncertainty shall be less than or equal to 0. db. Test durations must be sufficient to meet confidence level requirements. The actual E b /N t used in each test shall be within 0. db of the value indicated in Table A...- through Table A...-. For Radio Configuration Fundamental Channels, the mobile station shall set the Erasure Indicator Bit to in the second transmitted frame following the reception of any bad frame on the Forward Fundamental Channel. The value of the Erasure Indicator bits corresponding to all other frames received at the mobile station shall be 0. The FER for each test shall not exceed the piecewise linear FER curve specified by the points in Table A...- through Table A...- with % confidence (see. of []).. Demodulation Requirements for DB-CDMA-HRPD.. Demodulation of Forward Traffic Channel in AWGN Forward Traffic Channel closed loop power control in the CDMA base station shall be disabled during this test.... Definition The performance of the demodulation of the Forward Traffic Channel in an AWGN (no fading or multipath) environment is determined by the frame error rate (FER) for the CDMA channel and packet error rate (PER) for the HRPD channels. The PER and FER are calculated for each individual data rate and on a per carrier basis.... Method of Measurement. Connect the sector to the access terminal antenna connector as shown in Figure..- of [] (Figure..- of []).. For all band class combinations supported by the access terminal, configure the access terminal to operate with that band class combination, where B is the CDMA band class and B is the HRPD band class.. Perform steps through if the access terminal can simultaneously support a single CDMA carrier in B and one or more HRPD carriers in B.. Perform steps and if the access terminal can simultaneously support a single CDMA carrier in B and two or more HRPD carriers in B.. Configure the access terminal to transmit on a single CDMA carrier in B, and on a single HRPD carrier in B. Perform steps through.. For CDMA radio configurations and supported on the Forward Fundamental Channel, set up a CDMA call on B using Fundamental Channel (see. of []) with frame activity equal to 00%. -

26 . For HRPD on B, perform steps and. For Subtype 0 to Physical Layer tests, perform steps 0 through. For Subtype or Physical Layer tests, perform steps and.. Set the access network's forward HRPD packet activity to 00%. If the data rate under test is. Mbps or higher, an access network simulator meeting the waveform quality requirements in.. of [] shall be used. Set the access network s Control Channel data rate to. kbps.. Set the HRPD SetManagementSameChannelParameters attribute fields of the Default Route Update Protocol to the values specified below: 0 PilotDrop Field Value (Hex) 0xc (- db) Set up a HRPD Test Application session for B. Open a connection and configure the Test Application FTAP (for Subtype 0 or Physical Layer) so that the HRPD Forward Traffic Channel rate corresponds to the rate of the test only.. Set the test parameters for each HRPD demodulation test specified in Table A From the number of HRPD packets transmitted and the number of bad packets received, calculate the PER for this test. Unless otherwise specified, the PER shall be measured at the end of the packet.. If the access terminal supports HRPD Subtype or Subtype Physical Layer, set up a HRPD Test Application session for B. Open a connection and configure the Test Application FETAP (for Subtype or Physical Layer) so that the HRPD Forward Traffic Channel rate corresponds to the rate of the test only.. Set the test parameters for each HRPD demodulation test specified in Table A...- and repeat step.. Set the test parameters for each CDMA demodulation test as specified in Table A...- through Table A Count, at the base station, the number of CDMA frames transmitted and the number of good frames received at the mobile station.. Configure the access terminal to transmit on the maximum number of adjacent HRPD carriers supported by the access terminal on B.. If the access terminal supports multiple HRPD carriers in B, set up a HRPD Test Application session. Open a connection and configure the Test Application FMCTAP (for Subtype Physical Layer) so that the Forward Traffic Channel rate corresponds to the rate of the test only. Set the test parameters for tests and as specified in Table A...- and repeat step. The data rate and geometry parameters are on a per carrier basis. -

27 Minimum Standard for HRPD The actual E b /N t used in each test shall be within ±0. db of the value indicated in Table A...- through Table A...-. For access terminals that support HRPD Subtype 0 or Subtype Physical Layer, the PER shall not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. The PER should not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. For access terminals that support HRPD Subtype or Subtype Physical Layer, the PER shall not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. The PER should not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. For access terminals that support Subtype Physical Layer, for each active carrier the PER shall not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence. For access terminals that support Subtype Physical Layer, for each active carrier the PER should not exceed the piecewise linear PER curve specified by the points in Table A...- with % confidence.... Minimum Standard for CDMA The actual power measurement uncertainty shall be less than or equal to 0. db. Test durations must be sufficient to meet confidence level requirements. The actual E b /N t used in each test shall be within 0. db of the value indicated in Table A...- through Table A...-. The value of the Erasure Indicator bits corresponding to all frames received at the mobile station shall be 0. The FER for each test shall not exceed the piecewise linear FER curve specified by the points in Table A...- through Table A...- with % confidence (see. of []).. Receiver Performance for SB-CDMA-HRPD.. Receiver Sensitivity and Dynamic Range... Definition The RF sensitivity of the access terminal receiver is the minimum received power, measured at the access terminal antenna connector, at which the packet error rate (PER) for HRPD and the frame error rate (FER) for CDMA do not exceed a specified value. The receiver dynamic range is the input power range at the access terminal antenna connector over which the PER and FER do not exceed a specific value.... Method of Measurement. Connect the HRPD and CDMA sector(s) to the access terminal antenna connector as shown in Figure..- of [] (Figure..- of []). The AWGN generators and the CW generators are not applicable in this test. -

28 For each band class that the mobile station supports, configure the base station to operate in that band class. Configure the access terminal to simultaneously perform a CDMA and one or more HRPD calls as indicated in Table...-. Use a power control step size of 0.dB for CDMA as well as HRPD carriers. Perform steps through.. If the mobile station supports demodulation of Radio Configuration,,,, or, set up a CDMA call using Fundamental Channel Test Mode or (see. of []) with 00 bps data rate only, or Fundamental Channel Test Mode or (see. of []) with 00 bps data rate only. Perform steps through.. If the mobile station supports demodulation of Radio Configuration,,, or, set up a CDMA call using Fundamental Channel Test Mode (see. of []) with 00 bps data rate only and perform steps through.. For testing dynamic range (Test ), perform steps through. For testing sensitivity (Test ), perform steps through.. Set up a HRPD test Application session. Open a HRPD connection and configure the Test Application FTAP (for Subtype 0 OR Physical Layer) or FETAP (for Subtype Physical Layer) or FMCTAP (for Subtype Physical Layer) so that the Forward Traffic Channel rate corresponds to the one specified in Table...- for Test.. Set the test parameters for the CDMA and HRPD channels as specified in Table From the number of HRPD packets transmitted and the number of bad packets received, calculate the PER for HRPD. From the number of CDMA frames transmitted and the number of bad frames received, calculate the FER for CDMA.. For Test, open a HRPD connection and configure the Test Application FTAP (for Subtype 0 OR Physical Layer) or FETAP (for Subtype Physical Layer) or FMCTAP (for Subtype Physical Layer) so that the Forward Traffic Channel rate corresponds to the one specified in Table...- for Test. 0. Set the test parameters (all except Î or ) as specified in Table...-. Set Î or to - dbm/. MHz for each HRPD channel. Set Î or to - dbm/. MHz for the CDMA channel.. Send continuously alternate 0 and power control bits to the access terminal on the CDMA carrier, and send continuously 0 power control bits to the access terminal on each HRPD carrier and measure the total transmitted power at the access terminal until it becomes stable. For this test, denote this stable transmitted power value MaxAccessTerminalTxPower (in dbm).. Manually set the transmitted power on each CDMA and HRPD channel to MaxAccessTerminalTxPower 0 log 0 (N) Backoff, where N is the number of simultaneously active CDMA as well as HRPD carriers and Backoff is.db. Here, manual setting of the transmitted power implies using reverse power control commands to maintain the transmitted power close to a specified target. The -

29 difference between the target transmitted power and the actual or measured transmitted power shall not exceed the power control step size.. Set the Î or for Test for both CDMA and HRPD as specified in Table...- and repeat step. Table...-. Test Parameters for Receiver Sensitivity (Test ) and Dynamic Range (Test ) HRPD Parameter Units Test Test Î or dbm/. MHz Forward Traffic Channel Data Rate kbps 0. slots/packet CDMA Î or dbm/. MHz Pilot Ec db - Ior Traffic Ec db -. (RC and ) Ior -. (RC and ) -0. (RC ) Number of carriers N/A One CDMA channel and the One CDMA and one maximum number of HRPD HRPD Forward Forward Traffic channels Traffic channels at that can be demodulated by maximum allowable the AT. The HRPD carriers are all adjacent to one frequency separation another and adjacent to the supported by the single CDMA carrier with a spacing of. MHz (for device. The maximum Band Class 0) and. MHz separation should (for all other Band Classes) be at least between center frequencies..mhz Minimum Standard The PER for HRPD as well as FER for CDMA in both Test and Test shall not exceed 0.% with % confidence... Single Tone Desensitization... Definition For single carrier operation, the single tone desensitization is a measure of a receiver s ability to receive a CDMA or HRPD signal at its assigned channel frequency in the presence -

30 of an interferer spaced at a given frequency offset from the center frequency of the assigned channel. For multi-carrier operation, the single tone desensitization is a measure of a receiver s ability to receive a multi-carrier HRPD or CDMA-HRPD signal at its assigned channel frequencies in the presence of a single jammer spaced at a given frequency offset from the center frequency of the outermost channels. The receiver desensitization performance is measured by the packet error rate (PER) for HRPD and the frame error rate (FER) for CDMA. This test is applied to all band classes except Band Class, where no narrow-band interferers are currently known.... Method of Measurement. Connect the sectors and an interfering tone to the access terminal antenna connector as shown in Figure..- of [] (Figure..- of []). The GMSK tone is modulated as defined in [].. For each band class that the access terminal supports, except Band Class, configure the access terminal to operate in that band class. Use a power control step size of 0.dB for CDMA as well as HRPD carriers. Configure the access terminal to simultaneously perform a CDMA and a HRPD call with the two carriers at the maximum carrier separation supported by the device and perform steps through. The maximum carrier separation should be at least.mhz.. If the mobile station supports demodulation of Radio Configuration,,,, or, set up a CDMA call using Fundamental Channel Test Mode (see. of []) with 00 bps data rate only and perform steps through.. If the mobile station supports demodulation of Radio Configuration,,, or, set up a CDMA call using Fundamental Channel Test Mode (see. of []) with 00 bps data rate only and perform steps through.. Set up a HRPD Test Application session. Open a connection and configure the HRPD Test Application FTAP (for Subtype 0 or Physical Layer) or FETAP (for Subtype Physical Layer) so that the HRPD rate corresponds to the -slot version of 0. kbps.. Set the test parameters (excluding Î or ) for the CDMA channel and HRPD channel as specified in Test of Table Set Î or to - dbm/. MHz for the HRPD channel. Set Î or to - dbm/. MHz for the CDMA channel.. Send continuously alternate 0 and power control bits to the access terminal on the CDMA carrier, and send continuously 0 power control bits to the access terminal on the HRPD carrier and measure the total transmitted power at the access terminal until it becomes stable. For this test, denote this stable transmitted power value MaxAccessTerminalTxPower (in dbm).. Manually set the transmitted power on each CDMA and HRPD channel to MaxAccessTerminalTxPower 0 log 0 (N), where N is the number of -

31 0 simultaneously active CDMA as well as HRPD carriers. Here, manual setting of the transmitted power implies using reverse power control commands to maintain the transmitted power close to a specified target. The difference between the target transmitted power and the actual or measured transmitted power shall not exceed the power control step size. 0. Set the test parameters for Test as specified in Table...- and perform steps and.. Set the test parameters (excluding Î or ) for the CDMA channel and HRPD channel as specified in Test of Table...-. Repeat steps through. Set the test parameters for Test as specified in Table...- and perform steps and.. For Band Class, verify that the ERP is at a level higher than the minimum specified in Table...- for the current test. Otherwise, repeat steps 0 and until the EIRP or ERP reach desirable levels.. From the number of HRPD packets transmitted and the number of bad packets received calculate the PER for this test. From the number of CDMA frames transmitted and the number of bad frames received calculate the FER for this test. -

32 Table...-. Test Parameters for Single Tone Desensitization for CDMA-HRPD operation Parameter Units Test Test Jammer Offset from Carrier khz +00 from highest -00 from lowest frequency carrier frequency carrier (Band Groups 0 and (Band Groups 0 00, except BC ) and 00, except BC ) +00 (BC ) +0 from highest frequency carrier (BC,,, and ) Number of active carriers N/A CDMA + HRPD Jammer Power / Type HRPD CDMA Î or Î or Pilot Ec Ior Traffic Ior Ec dbm dbm/. MHz dbm/. MHz -00 (BC ) -0 from lowest frequency carrier (BC,,, and ) -0 GMSK (Except BC ) -0 CW (BC ) -. (Except BC ) -. (BC ) - (Except BC ) - (BC ) db - db -. Table...-. Minimum Effective Radiated Power for Single Tone Desensitization Test for Band Class I II Access terminal Class III Minimum Access terminal ERP Tests and - dbw (00 mw) - dbw (0 mw) - dbw ( mw) 0... Minimum Standard The FER for CDMA carriers and PER for HRPD carriers for each test shall not exceed.0% with % confidence (see. of [] and. of []). -0