SPECIFICATION Item no.: T60404-N4646-X662

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "SPECIFICATION Item no.: T60404-N4646-X662"

Transcription

1 SPECIFICATION Item no: T60404-N4646-X662 K-no: A Current Sensor for 5V- Supply Voltage Date: For electronic current measurement: DC, AC, pulsed, mixed, with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Customer: Standard type Customers Part no: Page 1 of 2 Description Closed loop (compensation) Current Sensor with magnetic field probe Printed circuit board mounting Casing and materials UL-listed Characteristics Excellent accuracy Very low offset current Very low temperature dependency and offset current drift Very low hysteresis of offset current Short response time Wide frequency bandwidth Compact design Reduced offset ripple Applications Mainly used for stationary operation in industrial applications: AC variable speed drives and servo motor drives Static converters for DC motor drives Battery supplied applications Switched Mode Power Supplies (SMPS) Power Supplies for welding applications Uninterruptible Power Supplies (UPS) Electrical data Ratings I Primary nominal rms current 15 A V out Output I P V Ref ± (0625*I P/I ) V V out Output I P=0, T A=25 C V Ref ± V V Ref External Reference voltage range 0 4 V Internal Reference voltage 25 ±0005 V K N Turns ratio 1 3 : 2000 Accuracy Dynamic performance data min typ max Unit I P,max Max measuring range ±51 X I, T A= 25 C 07 % ε L Linearity 01 % V out - V Ref Offset I P=0, T A= 25 C ±221 mv V o / V Ref / T Temperature drift of V I P=0, V Ref =2,5V, T A= C ppm/ C t r Response 90% von I 300 ns t (I P,max) Delay time at di/dt = 0 A/µs 200 ns f Frequency bandwidth DC 200 khz General data min typ max Unit T A Ambient operating temperature C T S Ambient storage temperature C m Mass 12 g V C Supply voltage V I C Current consumption 15 ma Constructed and manufactored and tested in accordance with EN (Pin 1-6 to Pin 7 ) Reinforced insulation, Insulation material group 1, Pollution degree 2 S clear Clearance (component without solder pad) 7,4 mm S creep Creepage (component without solder pad) 8,0 mm V sys System voltage overvoltage category 3 RMS 300 V V work Working voltage (tabel 7 acc to EN ) overvoltage category 2 RMS 650 V U PD Rated discharge voltage peak value 1320 V Max potential difference acc to UL 508 RMS 600 V AC Date Name Issue Amendment 1814 KRe 83 Marking changed from 4646X X Electrical data changed CN Hrsg: KB-E KB-PM: Sn Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages freig: HS

2 SPECIFICATION Item no: T60404-N4646-X662 K-no: A Current Sensor for 5V- Supply Voltage Date: For electronic current measurement: DC, AC, pulsed, mixed, with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Customer: Standard type Customers Part no: Page 2 of 2 Mechanical outline (mm): General tolerances DIN ISO 2768-c ,2 12,7 Tolerances grid distance ±0,2 mm Connections: 16: 1 mm 7: 0,46*0,46 mm Marking Marking: 24 UL-sign 4646-X F DC 0,5 1,84 7, ,54 Ø1,0 2,14 1,905 5,72 3,5±0,5 0,46x0,46 DC = Date Code F = Factory Schematic diagram int REF 680 V C 13 Ip + k 40k + 7 V ref IN / OUT R M k OUT - 8 V out 40k 46 9 GND Possibilities of wiring T A = 85 C) primary primary current output current turns ratio primary wiring windings RMS maximal RMS resistance N P I P [A] Î P,max [A] I S (I P) [ma] K N R P [mω] 1 15 ±51 25±0625 1: ±25 25±0625 2: ±17 25±0625 3: > > Temperature of the primary conductor should not exceed 1 C Additional information is obtainable on request This specification is no declaration of warranty acc BGB 443 > 3 1 > 4 6 > > Hrsg: KB-E KB-PM: Sn Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages freig: HS

3 Additional Information Item No: T60404-N4646-X662 K-No: A Current Sensor for 5V-Supply Voltage For the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Date: Customer: Customers Part No: Page 1 of 2 Electrical Data min typ max Unit V Ctot Maximum supply voltage (without function) 7 V I C Supply Current with primary current 15mA +I p*k N+V out/r L ma I out,sc Short circuit output current ±20 ma R P Resistance / primary T A=25 C 1 mω R S Secondary coil T A=85 C 67 Ω R i,ref Internal resistance of Reference input 670 Ω R i,(v out) Output resistance of V out 1 Ω R L External recommended resistance of V out 1 kω C L External recommended capacitance of V out 500 pf X Ti / T Temperature drift of T A = C 40 ppm/κ V 0 = (V out -V Ref) Sum of any offset drift including: 35 mv V 0t Longtermdrift of V 0 2 mv V 0T Temperature drift von V T A = C 2 mv V 0H Hysteresis of V I P=0 (after an overload of x I ) 3 mv V 0/ V C Supply voltage rejection ratio 1 mv/v v oss Offsetripple (with 1 MHz- filter first order) 30 mv v oss Offsetripple (with 0 khz- filter firdt order) 4 8 mv v oss Offsetripple (with 20 khz- filter first order) 12 2 mv C k Maximum possible coupling capacity (primary secondary) 5 pf Mechanical stress according to M3209/3 30g Settings: 2000 Hz, 1 min/octave, 2 hours Inspection (Measurement after temperature balance of the samples at room temperature) SC = significant characteristic V out (SC) (V) M3011/6: Output voltage vs external reference (I P=15A, 40-80Hz) 625±07% mv V out V Ref (I P=0) (V) M3226: Offset voltage ± 221 mv V d (V) M3014: Test voltage, rms, 1 s 15 kv pin 1 6 vs pin 7 V e (AQL 1/S4) Partial discharge voltage accm3024 (RMS) 1400 V with V vor (RMS) 1750 V Type Testing (Pin 1-6 to Pin 7 - ) Designed according standard EN with insulation material group 1 V W HV transient test according to M3064 (1,2 µs / 50 µs-wave form) 8 kv V d Testing voltage to M3014 (5 s) 3 kv V e Partial discharge voltage accm3024 (RMS) 1400 V with V vor (RMS) 1750 V Applicable documents Current direction: A positive output current appears at point I S, by primary current in direction of the arrow Enclosures according to IEC529: IP50 Further standards UL 508, file E317483, category NMTR2 / NMTR8 Datum Name Index Amendment 1814 Kre 83 Inspection M3011/6 defined as SC-value Offset voltage changed CN Le 83 Applicable documents further standards added Vctot changed from max 6 V in max 7 V CN-572 Hrsg: KB-E KB-PM: Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig: HS Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages

4 Additional Information Item No: T60404-N4646-X662 K-No: A Current Sensor for 5V-Supply Voltage For the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Date: Customer: Customers Part No: Page 2 of 2 Explanation of several of the terms used in the tablets (in alphabetical order) t r: t (I Pmax): V 0: Response time (describe the dynamic performance for the specified measurement range), measured as delay time at I P = 0,9 I between a rectangular current and the output voltage V OUt (I p) Delay time (describe the dynamic performance for the rapid current pulse rate eg short circuit current) measured between I Pmax and the output voltage V out(i Pmax) with a primary current rise of di P/dt 0 A/µs Offset voltage between V out and the rated reference voltage of V ref = 2,5V V o = V out(0) - 2,5V U PD Rated discharge voltage (recurring peak voltage separated by the insulation) proved with a sinusoidal voltage V e U PD = 2 * V e / 1,5 V vor Defined voltage is the RMS valve of a sinusoidal voltage with peak value of 1,875 * U PD required for partial discharge test in IEC V vor = 1,875 *U PD / 2 V sys System voltage RMS value of rated voltage according to IEC V work Working voltage voltage according to IEC which occurs by design in a circuit or across insulation V 0H: V 0t: Zero variation of V o after overloading with a DC of tenfold the rated value Long term drift of V o after 0 temperature cycles in the range -40 bis 85 C X: Permissible measurement error in the final inspection at RT, defined by ) (0) X = 0 1 % X ges(i ): Permissible measurement error including any drifts over the temperature range by the current measurement I ) 2,5V ) V X ges = 0 1 % or ref X ges = 0 1 % ε L: Linearity fault defined by I P P ) (0) ε L= 0 % I V ) V (0) out out This Additional information is no declaration of warranty according BGB 443 Hrsg: KB-E KB-PM: Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig: HS Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages

5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vacuumschmelze: T60404-N4646-X662

SPECIFICATION Item no.: T60404-N4646-X663

SPECIFICATION Item no.: T60404-N4646-X663 SPECIFICATION Item no: T60404-N4646-X663 K-no: 24513 6 A Current Sensor for 5V- Supply Voltage Date: 182014 For electronic current measurement: DC, AC, pulsed, mixed, with a galvanic isolation between

More information

SPECIFICATION Item no.: T60404-N4646-X651

SPECIFICATION Item no.: T60404-N4646-X651 VACUUMSCHMELZE SPECIFICATION Item no: T60404-N4646-X651 K-no: 24507 25 A Current Sensor modul for 5V-supply voltage Date: 10122010 For electronic current measurement: DC, AC, pulsed, mixed, with a galvanic

More information

SPECIFICATION Item no.: T60404-N4646-X100

SPECIFICATION Item no.: T60404-N4646-X100 VACUUMSCHMELZE SPECFCATON tem no.: T60404-N4646-X100 K-No.: 25033 100 A Current Sensor Date: 06.11.2007 For the electronic measurement of currents: solation between the primary circuit (high power) and

More information

SPECIFICATION Item no.: T60404-N4646-X410

SPECIFICATION Item no.: T60404-N4646-X410 VACUUMSCHMELZE SPECFCATON tem no.: T60404-N4646-X410 K-No.: 24616 50 A Current Sensor Date: 28.01.2008 For the electronic measurement of currents: solation between the primary circuit (high power) and

More information

SPECIFICATION Item no.: T60404-N4646-X300

SPECIFICATION Item no.: T60404-N4646-X300 SPECFCATON tem no: T60404-N4646-X300 K-No: 24577 Date: 16042014 For the electronic measurement of currents: solation between the primary circuit (high power and the secondary circuit (electronic circuit

More information

SPECIFICATION Item no.: T60404-N4646-X100

SPECIFICATION Item no.: T60404-N4646-X100 VACUUSCHELZE SPECFCATON tem no.: T60404-N4646-X100 For the electronic measurement of currents: solation between the primary circuit (high power) and the secondary circuit (electronic circuit) Customer:

More information

SPECIFICATION Item no.: T60404-N4644-X101

SPECIFICATION Item no.: T60404-N4644-X101 SPECFCATON tem no.: T60404-N4644-X0 K-no.: 50 A Current Sensor-Module Date: 24.02.204 solation between the primary circuit (electronic circuit) Customer: Standard type Customers Part no.: Page of 2 Description

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 510-S I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer CAS 25-NP/SP2 N = 25 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 2010-S I PN = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 510-S/SP13 I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

Ref: HLSR 10-SM, HLSR 16-SM, HLSR 20-SM, HLSR 32-SM, HLSR 40-SM, HLSR 50-SM

Ref: HLSR 10-SM, HLSR 16-SM, HLSR 20-SM, HLSR 32-SM, HLSR 40-SM, HLSR 50-SM Current Transducer HLSR-SM series N = 1... 5 A Ref: HLSR 1-SM, HLSR 16-SM, HLSR 2-SM, HLSR 32-SM, HLSR 4-SM, HLSR 5-SM For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation

More information

I PN. Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S

I PN. Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S Current Transducer HO-S series I PN = 50, 100, 150, 200, 240, 250 A Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S For the electronic measurement of current: DC, AC, pulsed..., with galvanic

More information

High Performance Current Transducer ITL 900-T = A

High Performance Current Transducer ITL 900-T = A High Performance Current Transducer ITL 900-T For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I PM = 0... 900 A Electrical

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 700-SB ULTRASTAB I PM = 700 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features ± 10 V voltage output

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 200-S ULTRASTAB I PM = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)

More information

AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS

AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS AUTOMOTIVE CURRENT TRANSDUCER HCF-SN CLIPS Introduction The HCF CLIPS Family is for the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive applications with galvanic

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer ITL 4000-S I PN = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed

More information

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017 Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175, ART-B22-D300 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and

More information

AUTOMOTIVE CURRENT SENSOR HC6H300-S

AUTOMOTIVE CURRENT SENSOR HC6H300-S AUTOMOTIVE CURRENT SENSOR HC6H300-S Page 1/ 5 Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive

More information

AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S

AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and

More information

DL2000ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.

DL2000ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators. DL000ID Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 6 ppm offset

More information

AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S

AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer ITC 2000-S/SP2 N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

Active. Advanced Materials The Key to Progress

Active. Advanced Materials The Key to Progress Active Current SEnsors FOR PCB MOUNTING Advanced Materials The Key to Progress The Company VACUUMSCHMELZE VACUUMSCHMELZE GmbH & Co. KG (VAC) is one of the world s leading producers of special metallic

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Voltage transducer V PN = 1 V Ref: DV 1/SP For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated

More information

V P N. Voltage transducer DVM 4200 = 4200 V

V P N. Voltage transducer DVM 4200 = 4200 V Voltage transducer DVM 42 N = 42 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated measurement

More information

Unipolar voltage - Current output 4-20 ma Ref: DVL 50-UI, DVL 150-UI, DVL 250-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI

Unipolar voltage - Current output 4-20 ma Ref: DVL 50-UI, DVL 150-UI, DVL 250-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI Current Transducer DVL-UI series V PN = 50... 1500 V Unipolar voltage - Current output 4-0 ma Ref: DVL 50-UI, DVL 150-UI, DVL 50-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI For the electronic

More information

V P N. Voltage transducer DVL 1000 = 1000 V

V P N. Voltage transducer DVL 1000 = 1000 V Voltage transducer DVL 1 V P N = 1 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Voltage transducer DVL 15 V PN = 15 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated

More information

HCPL-7840 Isolation Amplifier

HCPL-7840 Isolation Amplifier Products > Optocouplers - Plastic > Plastic Miniature Isolation Amplifier > HCPL-7840 HCPL-7840 Isolation Amplifier Description The HCPL-7840 isolation amplifier family was designed for current sensing

More information

I P I OUT R L. Applications. Standards. N 52.D ; Page 1/8

I P I OUT R L. Applications. Standards. N 52.D ; Page 1/8 Ref: ATO-10-B225-D10/SP3 r = 10 A ATO series is a split core current transformer for the electronic measurement of AC waveform current with galvanic separation between the primary circuit (power) and the

More information

AC/DC to Logic Interface Optocouplers Technical Data

AC/DC to Logic Interface Optocouplers Technical Data H AC/DC to Logic Interface Optocouplers Technical Data HCPL-37 HCPL-376 Features Standard (HCPL-37) and Low Input Current (HCPL-376) Versions AC or DC Input Programmable Sense Voltage Hysteresis Logic

More information

H11F1M, H11F2M, H11F3M Photo FET Optocouplers

H11F1M, H11F2M, H11F3M Photo FET Optocouplers , H11F2M, H11F3M Photo FET Optocouplers Features As a remote variable resistor: 100Ω to 300MΩ 15pF shunt capacitance 100GΩ I/O isolation resistance As an analog switch: Extremely low offset voltage 60

More information

AUTOMOTIVE CURRENT TRANSDUCER DHAB S/15

AUTOMOTIVE CURRENT TRANSDUCER DHAB S/15 AUTOMOTIVE CURRENT TRANSDUCER Introduction The DHAB family is best suited for DC, AC, or pulsed currents measurement in high power and low voltage automotive applications. Its contains galvanic isolation

More information

MAGNETIC INDUCTIVE FLOW SENSORS

MAGNETIC INDUCTIVE FLOW SENSORS JJ Series induq VMM JJ Series induq VMI JJ Series induq VMZ MAGNETIC INDUCTIVE FLOW SENSORS DB_Magnetic_Inductive_Flow_Sensors 7/217 69 Magnetic inductive flow sensors Principle of operation The smart

More information

150 μv Maximum Offset Voltage Op Amp OP07D

150 μv Maximum Offset Voltage Op Amp OP07D 5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply

More information

MSV200 - Hall effect transducer

MSV200 - Hall effect transducer - Hall effect transducer Datasheet Features Specially designed for railway applications Closed loop (compensated) High dielectric strength Precise linearity Precise accuracy High dynamic response No foucault

More information

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS, 110 C Rated

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS, 110 C Rated Optocoupler, Phototransistor Output, High Reliability, 53 V RMS, 11 C Rated 17918-2 DESCRIPTION The 11 C rated (DIP) feature a high current transfer ratio, low coupling capacitance and high isolation voltage.

More information

Current clamps for AC current

Current clamps for AC current Current clamps for AC current Small, compact and particularly resistant, this range of miniature clamps is designed for measurements from a few milli-amperes to 150 A AC. Their shape makes them very practical

More information

ASSR-601JV, ASSR-601JT

ASSR-601JV, ASSR-601JT Automotive Solid State Relay with R 2 Coupler TM Isolation Description The ASSR-61JV/JT is a high-voltage solid state relay that is designed for automotive applications. ASSR-61JV/JT consists of an AlGaAs

More information

SEATING PLANE FUNCTIONAL BLOCK DIAGRAM 8 LED

SEATING PLANE FUNCTIONAL BLOCK DIAGRAM 8 LED DESCRIPTION The Optically Isolated Amplifier consists of the popular RC41A precision programmable shunt reference and an optocoupler. The optocoupler is a gallium arsenide (GaAs) light emitting diode optically

More information

Technical catalogue. Current sensors Voltage sensors

Technical catalogue. Current sensors Voltage sensors Technical catalogue Current sensors Voltage sensors Current sensors Voltage sensors Contents Technologies Current measuring technology... 4 Voltage measuring technology... 8 Voltage detection technology...

More information

AUTOMOTIVE CURRENT TRANSDUCER HAB 60-S/SP5

AUTOMOTIVE CURRENT TRANSDUCER HAB 60-S/SP5 AUOMOIVE CURREN RANSDUCER HAB 60-S/SP5 Introduction he HAB Family is best suited for DC, AC or pulsed currents measurement in high power and low voltage automotive applications. It s contains galvanic

More information

Optocoupler, Phototransistor Output, Very High Isolation Voltage

Optocoupler, Phototransistor Output, Very High Isolation Voltage Vishay Semiconductors Optocoupler, Phototransistor Output, 787-4 DESCRIPTION CNY64 CNY65 CNY66 Top View A C The CNY64, CNY65, and CNY66 consist of a phototransistor optically coupled to a gallium arsenide

More information

IGBT Module H Bridge MIEB 101H1200EH. = 1200 V = 183 A V CE(sat) = 1.8 V V CES I C25. Part name (Marking on product) MIEB101H1200EH

IGBT Module H Bridge MIEB 101H1200EH. = 1200 V = 183 A V CE(sat) = 1.8 V V CES I C25. Part name (Marking on product) MIEB101H1200EH MIEB 11HEH IGBT Module H Bridge S 25 = = 183 (sat) = 1.8 Part name (Marking on product) MIEB11HEH 13, 21 1 T1 D1 9 T2 D2 2 1 19 E72873 3 T3 D3 11 T D 1, 2 Features: SPT + IGBT technology low saturation

More information

Preliminary Data Sheet

Preliminary Data Sheet 2SP0320T2Cx-12 Compact, high-performance, plug-and-play dual-channel IGBT driver based on SCALE -2 technology for individual and parallel-connected modules in 2-level, 3-level and multilevel converter

More information

Ripple & Max. capacitive Output Current

Ripple & Max. capacitive Output Current 0 Watts xxx Series Wide 4: Input Range Single Output Industry Standard /4 Brick -40 C to +0 C Operation 0 VDC Isolation Output Trim ±0% Remote On/Off Year Warranty Dimensions: QSC0:. x.4 x 0. (.9 x. x.

More information

MSA Hall effect transducer

MSA Hall effect transducer - Hall effect transducer Datasheet Features Specially designed for railway applications losed loop (compensated) High dielectric strength Precise linearity Precise accuracy High dynamic response No foucault

More information

ACPL-P480 and ACPL-W480

ACPL-P480 and ACPL-W480 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Description The high-speed ACPL-P48/W48 optocoupler contains a GaAsP LED, a photo detector, and a Schmitt trigger that eliminates

More information

DC/DC power module 5V / 3A / 15W

DC/DC power module 5V / 3A / 15W PKF 4211A I DC/DC power module 5V / 3A / 15W SMD and through-hole versions with ultra low component height 8.0 mm (0.315 in.) 81% efficiency at full load 1,500 Vdc isolation voltage Switching frequency

More information

PD30CNB25xxPS. Photoelectrics, Background suppression reflective - PointSpot. Main features. Main functions. Description

PD30CNB25xxPS. Photoelectrics, Background suppression reflective - PointSpot. Main features. Main functions. Description Photoelectrics, Background suppression reflective - PointSpot Main features Miniature sensor range The visible red PointSpot light makes alignment very easy Range: 250 mm Sensitivity adjustment by potentiometer

More information

Low Profile, 2.5 A Output Current IGBT and MOSFET Driver

Low Profile, 2.5 A Output Current IGBT and MOSFET Driver Low Profile, 2.5 A Output Current IGBT and MOSFET Driver 22677 DESCRIPTION The consists of an infrared light emitting diode optically coupled to an integrated circuit with a power output stage. This optocoupler

More information

ACNT-H79A, ACNT-H790 Optical Isolation Amplifier in 14.2mm Stretched SO-8 Package. Features. Applications

ACNT-H79A, ACNT-H790 Optical Isolation Amplifier in 14.2mm Stretched SO-8 Package. Features. Applications ACNT-H79A, ACNT-H790 Optical Isolation Amplifier in 14.2mm Stretched SO-8 Package Data Sheet Description The ACNT-H79A and ACNT-H790 isolation amplifiers are designed for current and voltage sensing in

More information

150 ma low quiescent current and low noise voltage regulator. Description

150 ma low quiescent current and low noise voltage regulator. Description LD39015 150 ma low quiescent current and low noise voltage regulator Datasheet - production data Compatible with ceramic capacitors C O = 1 µf Internal current and thermal limit Temperature range: -40

More information

Schematic V F HCPL-7601/11 SHIELD. USE OF A 0.1 µf BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS REQUIRED (SEE NOTE 1).

Schematic V F HCPL-7601/11 SHIELD. USE OF A 0.1 µf BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS REQUIRED (SEE NOTE 1). CMOS/TTL Compatible, Low Input Current, High Speed, High CMR Optocoupler Technical Data HCPL-7601 HCPL-7611 Features Low Input Current Version of HCPL-2601/11 and 6N137 Wide Input Current Range: I F =

More information

Precision, Low-Power, 6-Pin SOT23 Temperature Sensors and Voltage References

Precision, Low-Power, 6-Pin SOT23 Temperature Sensors and Voltage References 19-2457; Rev 2; 11/03 Precision, Low-Power, 6-Pin SOT23 General Description The are precise, low-power analog temperature sensors combined with a precision voltage reference. They are ideal for applications

More information

VariTrans P D1 TRMS

VariTrans P D1 TRMS Isolation Amplifiers Transmitters Indicators Process Analytics Portable Meters Laboratory Meters Sensors Fittings VariTrans P 41000 D1 TRMS VariTrans P 41000 TRMS AC/DC High-Voltage Transmitters With True

More information

MSA500 - Hall effect transducer

MSA500 - Hall effect transducer - Hall effect transducer Datasheet Features Specially designed for railway applications losed loop (compensated) High dielectric strength Precise linearity Precise accuracy High dynamic response No foucault

More information

T22. Torque transducer. Special features. Data sheet

T22. Torque transducer. Special features. Data sheet T22 Torque transducer Special features - Nominal (rated) torques 0.5 Nm, 1 Nm, 2 Nm, 5 Nm, Nm, Nm, 50 Nm, 0 Nm, 0 Nm, 500 Nm and 1 knm - Nominal (rated) rotational speed up to 000 rpm (depending on measuring

More information

±80V Fault-Protected, 2Mbps, Low Supply Current CAN Transceiver

±80V Fault-Protected, 2Mbps, Low Supply Current CAN Transceiver General Description The MAX3053 interfaces between the control area network (CAN) protocol controller and the physical wires of the bus lines in a CAN. It is primarily intended for industrial systems requiring

More information

2.5 A Output Current IGBT and MOSFET Driver

2.5 A Output Current IGBT and MOSFET Driver VO. A Output Current IGBT and MOSFET Driver 9 DESCRIPTION NC A C NC _ The VO consists of a LED optically coupled to an integrated circuit with a power output stage. This optocoupler is ideally suited for

More information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information HA-22, HA-22 Data Sheet August, 2 FN2894. 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-22/22 comprise a series of operational amplifiers delivering an unsurpassed

More information

Optocoupler, Phototransistor Output, Very High Isolation Voltage

Optocoupler, Phototransistor Output, Very High Isolation Voltage CNY64, CNY65, CNY66 Optocoupler, Phototransistor Output, 64 Top View A C 65 66 FEATURES Rated recurring peak voltage (repetitive) V IORM = V RMS Thickness through insulation 3 mm 4 Creepage current resistance

More information

ACPL-C87AT/ACPL-C87BT Automotive High Precision DC Voltage Isolation Sensor. Features. Applications

ACPL-C87AT/ACPL-C87BT Automotive High Precision DC Voltage Isolation Sensor. Features. Applications ACPL-CAT/ACPL-CBT Automotive High Precision DC Voltage Isolation Sensor Data Sheet Lead (Pb) Free RoHS fully compliant RoHS fully compliant options available; -xxxe denotes a lead-free product Description

More information

For non-electrical quantities

For non-electrical quantities Controlgear 3UG3 monitoring relays 3RS17 interface converters N nsb0346h nsb0348h nsb0775h For electrical quantities For non-electrical quantities 3RS17 interface converter Selection and ordering data

More information

QME48T40 DC-DC Series Data Sheet VDC Input; A Output

QME48T40 DC-DC Series Data Sheet VDC Input; A Output Applications Telecommunications Data communications Wireless communications Servers, Workstations Benefits High efficiency no heat sink required Higher current capability at 70 ºC than most competitors

More information

Industrial PSU with universal input voltage range ( VAC line to line) and configurable output voltage. North America

Industrial PSU with universal input voltage range ( VAC line to line) and configurable output voltage. North America World-Wide 3-phase Input Voltage Range (nom. 200 Vrms to 480 Vrms), PF > 0.94 High Power Density 16 W/in 3 94% Typical Efficiency Parallel Operation up to 16 Units (50.4 kw) Cold-Plate Cooling System -25

More information

MODEL 503 DC BRUSHLESS SERVO AMPLIFIER

MODEL 503 DC BRUSHLESS SERVO AMPLIFIER FEATURES Complete torque ( current ) mode functional block Drives motor with 60 or 20 Halls Single supply voltage 8-DC A continuous, 0A peak more than double the power output of servo chip sets Fault protected

More information

Current Sensor: ACS754SCB-200

Current Sensor: ACS754SCB-200 Pin 1: VCC Pin 2: GND Pin 3: VOUT Terminal 4: IP+ Terminal 5: IP AB SO LUTE MAX I MUM RAT INGS Supply Voltage, V CC...16 V Reverse Supply Voltage, V RCC... 16 V Output Voltage, V OUT...16 V Reverse Output

More information

OBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B

OBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B a FEATURES Excellent Noise Performance: 950 pv/ Hz or 1.5 db Noise Figure Ultralow THD: < 0.01% @ G = 100 Over the Full Audio Band Wide Bandwidth: 1 MHz @ G = 100 High Slew Rate: 17 V/ s typ Unity Gain

More information

ACPL-C87B, ACPL-C87A, ACPL-C870

ACPL-C87B, ACPL-C87A, ACPL-C870 Data Sheet ACPL-C87B, ACPL-C87A, ACPL-C87 Description The ACPL-C87B/C87A/C87 voltage sensors are optical isolation amplifiers designed specifically for voltage sensing. Its V input range and high -GΩ input

More information

ISOMETER Headline IR /IR

ISOMETER Headline IR /IR ISOMETER Headline IR155-323/IR155-324 Insulation Sub-Headline monitoring device (IMD) for unearthed DC drive systems (IT systems) in electric vehicles Version V4 Vorläufiges Datenblatt IR155-32xx-V4_D115_2_D_XXEN/9.216

More information

Description The HCPL-7840 isolation amplifier provides accurate, electrically isolated and amplified representations of voltage and current.

Description The HCPL-7840 isolation amplifier provides accurate, electrically isolated and amplified representations of voltage and current. H Analog Isolation Amplifier Technical Data HCPL- Features High Common Mode Rejection (CMR): kv/µs at V CM = V % Gain Tolerance.% Nonlinearity Low Offset Voltage and Offset Temperature Coefficient khz

More information

FU Steering Control Unit (Handwheel)

FU Steering Control Unit (Handwheel) Raytheon Anschütz GmbH Postfach 1166 D - 24100 Kiel Germany Tel+49-431-3019-0 Fax+49-431-3019-501 Email Service@raykiel.com www.raytheon -anschuetz.de FU Steering Control Unit (Handwheel) Type 105-106

More information

11/03/2013

11/03/2013 17.5 mm DIN rail mounting MUR1 Part number 88826105 TO BE SOON REPLACED BY THE NEW CHRONOS 2 RANGE (ref. 88827...) Relay or solid state output Multi-function or mono-function Multi-range Multi-voltage

More information

2SD106AI-17 UL Dual SCALE Driver Core

2SD106AI-17 UL Dual SCALE Driver Core 2SD106AI-17 UL Dual SCALE Driver Core for IGBTs and Power MOSFETs Description The SCALE drivers from CONCEPT are based on a chip set that was developed specifically for the reliable driving and safe operation

More information

AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX

AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX Introduction The CAB family is for battery monitoring applications where high accuracy and very low offset are required. Features Transducer

More information

LM2904AH. Low-power, dual operational amplifier. Related products. Description. Features. See LM2904WH for enhanced ESD performances

LM2904AH. Low-power, dual operational amplifier. Related products. Description. Features. See LM2904WH for enhanced ESD performances LM2904AH Low-power, dual operational amplifier Datasheet - production data Related products See LM2904WH for enhanced ESD performances Features Frequency compensation implemented internally Large DC voltage

More information

Features. Applications

Features. Applications ACPL-C87B, ACPL-C87A, ACPL-C87 Precision Optically Isolated Voltage Sensor Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description

More information

Data Sheet, V 1.1, Oct TLE4906H TLE4906L. High Precision Hall-Effect Switch. Sensors

Data Sheet, V 1.1, Oct TLE4906H TLE4906L. High Precision Hall-Effect Switch. Sensors Data Sheet, V 1.1, Oct. 2005 TLE4906H High Precision Hall-Effect Switch Sensors Edition 2005-10 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 München, Germany Infineon Technologies

More information

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output THN 20WI Series Application Note DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output Pending Applications Wireless

More information

LMC7101 A12A. Features. General Description. Applications. Ordering Information. Pin Configuration. Functional Configuration.

LMC7101 A12A. Features. General Description. Applications. Ordering Information. Pin Configuration. Functional Configuration. LMC7 LMC7 Low-Power Operational Amplifier Final Information General Description The LMC7 is a high-performance, low-power, operational amplifier which is pin-for-pin compatible with the National Semiconductor

More information

INTEGRATED CIRCUITS DATA SHEET. TDA1596 IF amplifier/demodulator for FM radio receivers. Product specification File under Integrated Circuits, IC01

INTEGRATED CIRCUITS DATA SHEET. TDA1596 IF amplifier/demodulator for FM radio receivers. Product specification File under Integrated Circuits, IC01 INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 April 1991 GENERAL DESCRIPTION The provides IF amplification, symmetrical quadrature demodulation and level detection for quality home

More information

TMT Series, 10 to 50 Watt. Order Code Output Power Output 1 PCB-Mount Chassis Mount max.

TMT Series, 10 to 50 Watt. Order Code Output Power Output 1 PCB-Mount Chassis Mount max. TMT Series, 10 to 50 Watt Features Ultra compact, fully encapsulated plastic case Single-, dual- and triple output models 2 package styles: - with screw terminal block for chassis mount - with solder pins

More information

Optocoupler, Photodarlington Output

Optocoupler, Photodarlington Output Optocoupler, Photodarlington Output C E FEATURES High isolation test voltage 5300 V RMS Standard plastic DIP-4 package Material categorization: for definitions of compliance please see www.vishay.com/doc?99912

More information

Features. Applications I DD1 V DD1 V IN+ V IN GND1. NOTE: A 0.1 µf bypass capacitor must be connected between pins 1 and 4 and between pins 5 and 8.

Features. Applications I DD1 V DD1 V IN+ V IN GND1. NOTE: A 0.1 µf bypass capacitor must be connected between pins 1 and 4 and between pins 5 and 8. HCPL-7 Isolated Linear Sensing IC Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The HCPL-7 isolated linear current

More information

P2 Power Solutions Pvt. Ltd. P2 Power Magnetics. Quality Power within your Reach. An ISO 9001:2008 Company

P2 Power Solutions Pvt. Ltd. P2 Power Magnetics. Quality Power within your Reach. An ISO 9001:2008 Company P2 Power Solutions Pvt. Ltd. An ISO 9001:2008 Company Quality Power within your Reach P2 Power Magnetics P2 Power Solutions Pvt. Ltd. P2 Power Solutions Pvt. Ltd. provides EMC and power quality solutions,

More information

Features. Regulated Converter. RAC05-K 5 Watt 1 x 1. Single Output RAC05- SK. AC/DC Converter

Features. Regulated Converter. RAC05-K 5 Watt 1 x 1. Single Output RAC05- SK. AC/DC Converter Features Regulated Converter Description 5W Class II power supply in compact 1 x 1 Package (high power density) Internal EMC class B filter UL/IEC/EN695-1 certified UL/IEC/EN62368-1 certified Electrical

More information

N-channel TrenchMOS transistor

N-channel TrenchMOS transistor PSMN9-W FEATURES SYMBOL QUICK REFERENCE DATA Trench technology Very low on-state resistance Fast switching Low thermal resistance g d s V DSS = V I D = A R DS(ON) 9 mω GENERAL DESCRIPTION PINNING SOT429

More information

SE014S110 Power Module; dc-dc Converter: 48 Vdc Input, 110 Vdc Output, 14 W

SE014S110 Power Module; dc-dc Converter: 48 Vdc Input, 110 Vdc Output, 14 W Data Sheet SE014S110 Power Module; dc-dc Converter: Features The SE014S110 Power Module uses advanced, surface-mount technology and delivers high-quality, compact, dc-dc conversion at an economical price.

More information

Precision Gain of 5 Instrumentation Amplifier AD8225

Precision Gain of 5 Instrumentation Amplifier AD8225 Precision Gain of Instrumentation Amplifier AD8 FEATURES No External Components Required Highly Stable, Factory Trimmed Gain of Low Power, 1. ma Max Supply Current Wide Power Supply Range ( 1.7 V to 18

More information

Triple Voltage Regulator TLE 4471

Triple Voltage Regulator TLE 4471 Triple Voltage Regulator TLE 4471 Features Triple Voltage Regulator Output Voltage 5 V with 450 ma Current Capability Two tracked Outputs for 50 ma and 100 ma Enable Function for main and tracked Output(s)

More information

Isolation Amplifier. Technical Data HCPL-7800A HCPL-7800

Isolation Amplifier. Technical Data HCPL-7800A HCPL-7800 Isolation Amplifier Technical Data HCPL-800A HCPL-800 Features 15 kv/µs Common-Mode Rejection at V CM = 1000 V Compact, Auto-Insertable Standard 8-pin DIP Package 0.00025 V/V/ C Gain Drift vs. Temperature

More information

High Accuracy 8-Pin Instrumentation Amplifier AMP02

High Accuracy 8-Pin Instrumentation Amplifier AMP02 a FEATURES Low Offset Voltage: 100 V max Low Drift: 2 V/ C max Wide Gain Range 1 to 10,000 High Common-Mode Rejection: 115 db min High Bandwidth (G = 1000): 200 khz typ Gain Equation Accuracy: 0.5% max

More information

P-Channel 20 V (D-S) MOSFET

P-Channel 20 V (D-S) MOSFET Si30CDS P-Channel 0 V (D-S) MOSFET MOSFET PRODUCT SUMMARY V DS (V) R DS(on) ( ) I D (A) a Q g (Typ.) - 0 0. at V GS = - 4.5 V - 3. 0.4 at V GS = -.5 V -.7 3.3 nc TO-36 (SOT-3) FEATURES Halogen-free According

More information

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS Optocoupler, Phototransistor Output, High Reliability, 53 V RMS A C 1 2 4 3 C E FEATURES Operating temperature from -55 C to +11 C Good CTR linearity depending on forward current Isolation test voltage,

More information

Optocoupler, Phototransistor Output, AC Input, Single / Quad Channel, Half Pitch Mini-Flat Package

Optocoupler, Phototransistor Output, AC Input, Single / Quad Channel, Half Pitch Mini-Flat Package TCMT16, TCMT46, TCMT466 Optocoupler, Phototransistor Output, AC Input, Single / Quad Channel, Half Pitch Mini-Flat Package FEATURES Low profile package (half pitch) 22775 22628-1 C E 9 AC isolation test

More information