Instruction Manual. item no. : SPR0113

Size: px

Start display at page:

Download "Instruction Manual. item no. : SPR0113"

Howard Harper
6 years ago
Views:

1 Instruction Manual item no. : SPR0

2 . Introduction... p.. Safty Guides... p.. Battery Charging notes... p.4 4. Transmitter and Receiver parameters...p.5 - p.6 5. Receiver Connectivity...p G Operation notes...p.8 - p.9 7. Transmitter Function notes...p.0 - p. 8. Memo...p. - p.4

3 Thank you for choosing our.4g digital radio control products, Please read through this manual to familiarize yourself with the operation of the transmitter before use. Keep this manual for future troubleshooting if you have any problems during operation. Once again, thanks for buying our products, This product is warranted against manufacturing defects for a period of one year after purchase. This warranty does not cover abuse or physical damage caused by the user. Please visit for warranty service contact information in your region and return instructions. If you find any problems during operation, please refer to this manual for a solution. If the problem still exists, please visit

4 Please pay attention to the following symbols when they appear in the manual, and please read carefully.! Danger: Failure to follow these instructions, may lead to serious injuries or mortal danger.! Warning: Failure to follow these instructions, may lead to serious injuries or mortal danger.! Attention: Failure to follow these instructions, may lead to minor injuries. Prohibition! Mandatory Do not operate in bad weather such as rain or thunderstorms to assure the safety of you and others.!!! Before you operate, please make sure the direction of the radio movements match with the direction of car movements. If not, please adjust before driving. Always turn on the transmitter first, then turn on the receiver. Always turn off the receiver power first, then turn off the transmitter power. If the above operations are reversed, it might lead to an uncontrolled vehicle and accident.

5 ! Check your transmitter batteries before each use. Low battery power will cause poor range, slow response, inconsistent response and loss of control. If your battery power is low, please charge before use.! If you are using a nickel-cadmium, nickel-metal hydride batteries for recharging, please use the supplied charger. Other chargers may overcharge the batteries and lead to fire. Please turn off the power immediately after recharging. Remove batteries from the transmitter before storing it for long periods.. Install the transmitter batteries with correct polarity, and replace the cover.. Connect the charger to the AC Outlet.. Connect the charger to the transmitter AC Jack. 4. Cut off the power supply immediately after recharge completed. AC Outlet Charger

6 Specifications: - Channels: Channels - Model type: Car/Boat - RF power: less than 0dbm - Modulation: GFSK - Code type: Digital - Sensitivity: 04 - Low voltage warning: Yes(less than 9W) - DSC port: Yes(.5mm) - Charger port: Yes - Power: vdc(.5aa*8) - Weight: 57g - ANT length: 6mm - Size: 7 X 68 X 97mm - Certificate: CE FCC Specifications: - Channels: Channels - Model type: Car/Boat - Frequency bank:.4g - Modulation: GFSK - Sensitivity: 04 - RF. receiver sensitivity: -00dbm - Power: 4.5-6vdc - Weight: 6g - ANT length: 6mm - Size: 6.5 X. X.mm - Certificate: CE FCC

7 NOR REV NOR 4 On/Off Switch.4G Antenna Steering Wheel Throttle Trigger 4 5 Battery Box CHG DSC 6 7 REV RADIO 0 BIND POWER G:FULL LED F:LOW ST.TRIM TH.TRIM ST.D/R Charger Jack 0 Power LED 4 Throttle Trim 7 DSC for Simulate Battery Indicator LED 5 Steering Dual Rate Dail 8 Steering Revise Radio Bind 6 Head LED Switch 9 Throttle Revise Steering Trim 7 Head LED

8 ESC Switch Servo Motor Battery Receiver Switch Battery (.5AA X4) Throttle Receiver Steering System Servo Note: Route the antenna of the receiver straight up, and avoid metal or wires to assure its sensitivity. Antenna Receiver

9 Our products are bound from the factory, so you do not need to bind them yourself. To bind the receiver with another transmitter, please follow the following steps: A. Install the battery to.4g transmitter B. Insert the bind plug to the channel BIND /CH port of the receiver. C. Connect the receiver battery to VCC port of the receiver. The two LED will be flashing and this means the receiver is ready to bind. D. Press and hold the bind button on the transmitter, and then switch on the power. E. Observe the LED on the receiver, if the LED is not flashing, the bind was successful.(may take about 5s ) F. Release the bind button on the transmitter, and remove the bind plug from the receiver. G. Install a servo and test. H. If the test fails, please repeat the process above. I. If the tests succeeds, the bind is complete. (The above ways of match is only suitable on this products) NOR REV NOR POWER LED RADIO BIND REV G:FULL F:LOW 0 LED ST.TRIM TH.TRIM ST.D/R Bind Plug

10 A. Complete installation. B. Turn on transmitter. -. Press the antenna untill it press the On/Off switch. -. Flip the antenna to vertical position. C. Turn on receiver. D. Receiver LED light should be solid. E. Ready to use. A. Turn off the receiver. B. Turn off transmitter. -. Flip the antenna down untill it press the On/Off switch.

11 fig. fig.

12 fig. fig.4

13 NOR REV NOR POWER LED RADIO BIND REV G:FULL F:LOW ST.TRIM TH.TRIM ST.D/R LED Button

16 Tel: (85) Fax: (85) USA Support USA Toll Free line:

CX-CT6A INSTRUCTION MANUAL. Computer Transmitter. Digital Propotional Radio Control System. 6 channel Radio Control System

CX-CT6A INSTRUCTION MANUAL. Computer Transmitter. Digital Propotional Radio Control System. 6 channel Radio Control System CX-CT6A INSTRUCTION MANUAL 6 channel Radio Control System Digital Propotional Radio Control System www.copterx.com Copyright 2008 KY MODEL Company Limited. MENU Table of content.........................................................................