FS Programmable Line Lock Clock Generator IC

Transcription

1 .0 Features Complete programmable control via I 2 C -bus Selectable CMOS or PECL compatible outputs External eedback loop capability allows genlocking Tunable VCXO loop or jitter attenuation Commercial (FS63-0 and industrial (FS63-0i temperature versions available 3.0 Applications Frequency Synthesis Line-Locked and Genlock Applications Clock Multiplication Telecom Jitter Attenuation Figure : Pin Coniguration 2.0 Description The FS63-0 is a monolithic CMOS clock generator/regenerator IC designed to minimize cost and component count in a variety o electronic systems. Via the I 2 C- bus interace, the FS63-0 can be adapted to many clock generation requirements. The ability to tune the on-board voltage-controlled crystal oscillator (VCXO, the length o the Reerence and Feedback Dividers, their granularity, and the lexibility o the Post Divider make the FS63-0 the most lexible stand-alone phase-locked loop (PLL clock generator available. SCL SDA ADDR VSS XIN XOUT XTUNE VDD FS pin 0.50" SOIC CLKN CLKP VDD FBK REF VSS EXTLF LOCK/IPRG Figure 2: Block Diagram LFTC XTUNE (optional XIN XOUT (optional XCT[3:0], XLVTEN VCXO Control ROM VCXO Divider XLROM[2:0] XLPDEN, XLSWAP Phase- Frequency Detector CRYSTAL LOOP UP Charge Pump DOWN XLCP[:0] EXTLF Internal Loop Filter 0 STAT[:0] C LF R LF C LP EXTLF (optional REF FBK ADDR SCL SDA 0 ( REF REFDSRC I 2 C Interace REFDIV[:0] Reerence Divider (N R 0 0 PDREF PDFBK Registers Phase- Frequency Detector UP Charge Pump DOWN Feedback Divider (N F FBKDIV[3:0] MLCP[:0] VCOSPD, OSCTYPE Voltage Controlled Oscillator FBKDSRC[:0] ( VCO GBL Clock Gobbler OUTMUX[:0] MAIN LOOP POST3[:0] POST2[:0] POST[:0] Post Divider (N Px Lock Detect 0 CMOS CMOS/PECL Output FS63 LOCK/ IPRG (optional CLKP ( CLK CLKN I 2 C is a licensed trademark o Philips Electronics, N.V. Windows and Windows NT are registered trademarks o Microsot Corporation. American Microsystems, Inc. reserves the right to change detail speciications as may be required to permit improvements in the design o its products.

2 Table : Pin Descriptions Key: AI = Analog Input; AO = Analog Output; DI = Digital Input; DI U = Input with Internal Pull-Up; DID = Input with Internal Pull-Down; DIO = Digital Input/Output; DI-3 = Three-Level Digital Input, DO = Digital Output; P = Power/Ground; # = Active Low pin PIN TYPE NAME DESCRIPTION DI SCL Serial Interace Clock (requires an external pull-up 2 DIO SDA Serial Interace Data Input/Output (requires an external pull-up 3 DI ADDR Address Select Bit (see Section P VSS Ground 5 AI XIN VCXO Feedback 6 AO XOUT VCXO Drive 7 AI XTUNE VCXO Tune 8 P VDD Power Supply (+5V 9 DIO LOCK/IPRG Lock Indicator / PECL Current Drive Programming 0 AI EXTLF External Loop Filter P VSS Ground 2 DI REF Reerence Frequency Input 3 DI FBK Feedback Input 4 P VDD Power Supply (+5V 5 DO CLKP Dierential Clock Output (+ 6 DO CLKN Dierential Clock Output (- 4.0 Functional Block Description 4. Main Loop PLL The Main Loop Phase Locked Loop (ML-PLL is a standard phase- and requency- locked loop architecture. As shown in Figure 2, the ML-PLL consists o a Reerence Divider, a Phase-Frequency Detector (PFD, a charge pump, an internal loop ilter, a Voltage-Controlled Oscillator (VCO, a Feedback Divider, and a Post Divider. During operation, the reerence requency ( REF, generated by either the on-board crystal oscillator or an external requency source, is irst reduced by the Reerence Divider. The integer value that the requency is divided by is called the modulus, and is denoted as N R or the Reerence Divider. The divided reerence is then ed into the PFD. The PFD controls the requency o the VCO ( VCO through the charge pump and loop ilter. The VCO provides a high-speed, low noise, continuously variable requency clock source or the ML-PLL. The output o the VCO is ed back to the PFD through the Feedback Divider (the modulus is denoted by N F to close the loop. 2 The PFD will drive the VCO up or down in requency until the divided reerence requency and the divided VCO requency appearing at the inputs o the PFD are equal. The input/output relationship between the reerence requency and the VCO requency is N VCO REF =. F N R I the VCO requency is used as the PLL output requency ( CLK then the basic PLL equation can be rewritten as = N N CLK REF F. R 4.. Reerence Divider The Reerence Divider is designed or low phase jitter. The divider accepts either the output o either the Crystal Loop (the VCXO output or an external reerence requency, and provides a divided-down requency to the PFD. The Reerence Divider is a 2-bit divider, and can be programmed or any modulus rom to See both Table 3 and Table 8 or additional programming inormation.

3 4..2 Feedback Divider The Feedback Divider is based on a dual-modulus prescaler technique. The technique allows the same granularity as a ully programmable eedback divider, while still allowing the programmable portion to operate at low speed. A high-speed pre-divider (also called a prescaler is placed between the VCO and the programmable Feedback Divider because o the high speeds at which the VCO can operate. The dual-modulus technique insures reliable operation at any speed that the VCO can achieve and reduces the overall power consumption o the divider. For example, a ixed divide-by-eight could be used in the Feedback Divider. Unortunately, a divide-by-eight would limit the eective modulus o the eedback divider path to multiples o eight. The limitation would restrict the ability o the PLL to achieve a desired input-requency-tooutput-requency ratio without making both the Reerence and Feedback Divider values comparatively large. Large divider moduli are generally undesirable due to increased phase jitter. Figure 3: Feedback Divider vco Dual- Modulus Prescaler A Counter M Counter To understand the operation, reer to Figure 3. The M- counter (with a modulus o M is cascaded with the dualmodulus prescaler. I the prescaler modulus were ixed at N, the overall modulus o the eedback divider chain would be M N. However, the A-counter causes the prescaler modulus to be altered to N+ or the irst A outputs o the prescaler. The A-counter then causes the dual-modulus prescaler to revert to a modulus o N until the M-counter reaches its terminal state and resets the entire divider. The overall modulus can be expressed as A( N + + N ( M A, where M A, which simpliies to M N + A Feedback Divider Programming The requirement that M A means that the Feedback Divider can only be programmed or certain values below a divider modulus o 56. The selection o divider values is listed in Table 2. I the desired Feedback Divider is less than 56, ind the divider value in the table. Follow the column up to ind the A-counter program value. Follow the row to the let to ind the M-counter value. Above a modulus o 56, the Feedback Divider can be programmed to any value up to See both Table 3 and Table 8 or additional programming inormation. Table 2: Feedback Modulus Below 56 M-COUNTER: FBKDIV[3:3] A-COUNTER: FBKDIV[2:0] FEEDBACK DIVIDER MODULUS 4..4 Post Divider The Post Divider consists o three individually programmable dividers, as shown in Figure 4. Figure 4: Post Divider GBL POST[:0] Post Divider (N P POST2[:0] Post Divider 2 (N P2 POST DIVIDER (N Px POST3[:0] Post Divider 3 (N P3 out The moduli o the individual dividers are denoted as N P, N P2, and N P3, and together they make up the array modulus N Px. N = N N N Px P P 2 P3 3

4 The Post Divider perorms several useul unctions. First, it allows the VCO to be operated in a narrower range o speeds compared to the variety o output clock speeds that the device is required to generate. Second, it changes the basic PLL equation to CLK = REF N N F R N The extra integer in the denominator permits more lexibility in the programming o the loop or many applications where requencies must be achieved exactly. Note that a nominal 50/50 duty actor is preserved or selections which have an odd modulus. 4.2 Phase Adjust and Sampling In line-locked or genlocked applications, it is necessary to know the exact phase relation o the output clock relative to the input clock. Since the VCO is included within the eedback loop in a simple PLL structure, the VCO output is exactly phase aligned with the input clock. Every cycle o the input clock equals N R /N F cycles o the VCO clock. Figure 5: Simple PLL IN IN OUT Reerence Divider (N R Phase Frequency Detect Px Feedback Divider (N F VCO. OUT 4.2. Clock Gobbler (Phase Adjust The Clock Gobbler circuit takes advantage o the unknown relationship between input and output clocks to permit the adjustment o the CLKP/CLKN output clock phase relative to the REF input. The Clock Gobbler circuit removes a VCO clock pulse beore the pulse clocks the Post Divider. In this way, the phase o the output clock can be slipped until the output phase is aligned with the input clock phase. To adjust the phase relationship, switch the Feedback Divider source to the Post Divider input via the FBKDSRC bit, and toggle the GBL register bit. The Clock Gobbler output clock is delayed by one VCO clock period or each transition o the GBL bit rom zero to one Phase Alignment To maintain a ixed phase relation between input and output clocks, the Post Divider must be placed inside the eedback loop. The source or the Feedback Divider is obtained rom the output o the Post Divider via the FBKDSRC switch. In addition, the Feedback Divider must be dividing at a multiple o the Post Divider. Figure 7: Aligned I/O Phase IN IN OUT Reerence Divider (N R Phase Frequency Detect VCO Feedback Divider (N F Post Divider (N F OUT The addition o a Post Divider, while adding lexibility, makes the phase relation between the input and output clock unknown because the Post Divider is outside the eedback loop. Figure 6: PLL with Post Divider IN IN Reerence Divider (N R VCO? OUT Phase Frequency Detect VCO Feedback Divider (N F VCO Post Divider (N F OUT Phase Sampling and Initial Alignment However, the ability to adjust the phase is useless without knowing the initial relation between output and input phase. To aid in the initial synchronization o the output phase to input phase, a Phase Align lag makes a transition (zero to one or one to zero when the output clock phase becomes aligned with the eedback source phase. The eedback source clock is, by deinition, locked to the input clock phase. First, the FS63 is used to sample the output clock with the eedback source clock and set/clear the Phase Align lag when the two clocks match to within a eedback source clock period. Then, the Clock Gobbler is used to delay the output phase relative to the input phase one VCO clock at a time until a transition on the lag occurs. When a transition occurs, the output and input clocks are phase aligned.

5 To enter this mode, set STAT[] to one and clear STAT[0] to zero. I the CMOS bit is set to one, the LOCK/IPRG pin can display the lag. The lag is always available under sotware control by reading back the STAT[] bit, which will be overwritten by the lag in this mode Feedback Divider Monitoring The Feedback Divider clock can be brought out the LOCK/IPRG pin independent o the output clock to allow monitoring o the Feedback Divider clock. To enter this mode, set both the STAT[] and STAT[0] bits to one. The CMOS bit must also be set to one to enable the LOCK/IPRG pin as an output. 4.3 Loop Gain Analysis For applications where an external loop ilter is required, the ollowing analysis example can be used to determine loop gain and stability. The loop gain o a PLL is the product o all o the gains within the loop. Establish the basic operating parameters: Set the charge pump current: Set the loop ilter values: Set the VCO gain (VCOSPD: I chgpump = 0µ A R LF C C 2 = 5kΩ = 0.05µ F = 220 pf A VCO = 230MHz / V Set the Feedback Divider: N F = 3500 Set the Reerence requency (at the input to the Phase Detector: REF = 20kHz The transer unction o the Phase Detector and Charge Pump combination is (in A/rad: K = PD I chgpump 2π The transer unction o the loop ilter is (in V/A: K LF ( s = sc 2 + R LF + sc 5 The VCO transer unction (in rad/s, and accounting or the phase integration that occurs in the VCO is: K VCO ( s = 2πA VCO The transer unction o the Feedback Divider is: K F = N Finally, the sampling eect that occurs in the Phase Detector is accounted or by: K SAMP e ( s = The loop gain o the PLL is: K F s s REF s REF ( s K K ( s K ( s K K ( s LOOP = PD VCO Figure 8: Loop Gain vs. Frequency Amplitude LF Frequency ( i F SAMP 0.kHz khz 0kHz 00kHz

6 The loop phase angle is: = arg [ K ( j2π ] Θ. i LOOP Figure 9: Loop Phase vs. Frequency -00 Phase kHz khz 0kHz 00kHz Frequency ( i A Nyquist plot o gain vs. amplitude is shown below. Figure 0: Loop Nyquist Plot Amplitude 80 Phase Margin Gain Margin Phase i Voltage-Controlled Crystal Oscillator The VCXO provides a tunable, low-jitter requency reerence or the rest o the FS63 system components. Loading capacitance or the crystal is internal to the device. No external components (other than the resonator itsel are required or operation o the VCXO. The resonator loading capacitance is adjustable under register control. This eature permits actory coarse tuning o inexpensive resonators to the necessary precision or digital video applications. Continuous ine-tuning o the VCXO requency is accomplished by varying the voltage on the XTUNE pin. The total change (rom one extreme to the other in eective loading capacitance is.5pf nominal, and the eect is shown in Figure. The oscillator operates the crystal resonator in the parallelresonant mode. Crystal warping, or the pulling o the crystal oscillation requency, is accomplished by altering the eective load capacitance presented to the crystal by the oscillator circuit. The actual amount that changing the load capacitance alters the oscillator requency will be dependent on the characteristics o the crystal as well as the oscillator circuit itsel. The motional capacitance o the crystal (usually reerred to by crystal manuacturers as C, the static capacitance o the crystal (C 0, and the load capacitance (C L o the oscillator determine the warping capability o the crystal in the oscillator circuit. A simple ormula to determine the total warping capability o a crystal is C ( ppm = 2 C 6 ( C L2 C L 0 ( + ( +, 0 where C L and C L2 are the two extremes o the applied load capacitance obtained rom Table. Example: A crystal with the ollowing parameters is used with the FS63. The total coarse tuning range is: C =0.02pF, C 0 =5.0pF, C L =0.0pF, C L2 =22.66pF C L2 6 ( ( ( C 0 C L = = 305 ppm 2 6

7 4.4. VCXO Tuning The VCXO may be coarse tuned by a programmable adjustment o the crystal load capacitance via the XCT[3:0] control bits. See Table or the control code and the associated loading capacitance. The actual amount o requency warping caused by the tuning capacitance will depend on the crystal used. The VCXO tuning capacitance includes an external 6pF load capacitance (2pF rom the XIN pin to ground and 2pF rom the XOUT pin to ground. The ine tuning capability o the VCXO can be enabled by setting the XLVTEN bit to a one, or disabled by setting it to a zero. Figure shows the typical eect o the coarse and ine tuning mechanisms. The total coarse tune range is about 350ppm. The dierence in VCXO requency in parts per million (ppm is shown as the ine tuning voltage on the XTUNE pin varies rom 0V to 5V. Note that as the crystal load capacitance is increased the VCXO requency is pulled somewhat less with each coarse step, and the ine tuning range decreases. The ine tuning range always overlaps a ew coarse tuning ranges, eliminating the possibility o holes in the VCXO response. The dierent crystal warping characteristics may change the scaling on the Y-axis, but not the overall characteristic o the curves. Figure : VCXO Coarse and Fine Tuning VCXO Range (ppm VCXO Range (ppm vs. XTUNE Voltage (V XTUNE Voltage = 0.0V XTUNE Voltage = 5.0V 4.5 Crystal Loop The Crystal Loop is designed to attenuate the jitter on a highly jittered, low-q, low requency reerence. The Crystal Loop can also maintain a constant requency output into the Main Loop i the low requency reerence is intermittent. The Crystal Loop consists o a Voltage-Controllable Crystal Oscillator (VCXO, a divider, a PFD, and a charge pump that tunes the VCXO to a requency reerence. The requency reerence is phase-locked to the divided requency o an external, high-q, jitter-ree crystal, thereby locking the VCXO to the reerence requency. The VCXO can continue to run o the crystal even i the requency reerence becomes intermittent Locking to an External Frequency Source When the Crystal Loop is synchronized to an external requency source, the FS63 can monitor the Crystal Loop and detect i the loop unlocks rom the external source. The Crystal Loop tries to drive to zero requency i the external source is dropped, and sets a Lock Status error lag. The Crystal Loop can also detect i the VCXO has dropped out o the Fine Tune range, requiring a change to the Coarse Tune. The Lock Status also latches the direction the loop went out o range (high or low when the loop became unlocked Crystal Loop Lock Status Flag To enable this mode, clear the STAT[] and STAT[0] bits to zero. I the CMOS bit is set to one, the LOCK/IPRG pin will be low i the Crystal Loop becomes unlocked. The lag is always available under sotware control by reading back the STAT[] bit, which is overwritten with a the status lag (low = unlocked in this mode (see Table Coarse Tune Setting XCT[3:0] 7

8 Out-O-Range High/Low The direction the loop has gone out-o-range can be determined by clearing STAT[] to zero and setting STAT[0] bit to one. I the CMOS bit is set to one, the LOCK/IPRG pin will go high i the Crystal Loop went out o range high. I the pin goes to a logic-low, the loop went out o range low. The out-o-range inormation is also available under sotware control by reading back the STAT[] bit, which is overwritten by the lag (high = out-o-range high, low = out-o-range low in this mode. The bit is set or cleared only i the Crystal Loop loses lock (see Table Crystal Loop Disable The Crystal Loop is disabled by setting the XLPDEN bit to a logic-high (. The bit disables the charge pump circuit in the loop. Setting the XLPDEN bit low (0 permits the crystal loop to operate as a control loop. 4.6 Connecting the FS63 to an External Reerence Frequency I a crystal oscillator is not used, tie XIN to ground and shut down the crystal oscillator by setting XLROM[2:0]=. The REF and FBK pins do not have pull-up or pull-down current, but do have a small amount o hysteresis to reduce the possibility o extra edges. Signals may be ACcoupled into these inputs with an external DC-bias circuit to generate a DC-bias o 2.5V. Any Reerence or Feedback signal should be square or best results, and the signals should be rail-to-rail. Unused inputs should be grounded to avoid unwanted signal injection. 4.7 Dierential Output Stage The dierential output stage supports both CMOS and pseudo-ecl (PECL signals. The desired output interace is chosen via the program registers (see Table 4. I a PECL interace is used, the transmission line is usually terminated using a Thévenin termination. The output stage can only sink current in the PECL mode, and the amount o sink current is set by a programming resistor on the LOCK/IPRG pin. The ratio o IPRG current to output drive current is shown in Figure 2. Source current is provided by the pull-up resistor that is part o the Thévenin termination. Figure 2: IPRG to CLKP/CLKN Current IPRG Input Current (ma CLKP/CLKN PECL Output Current (ma 8

9 5.0 I 2 C-bus Control Interace This device is a read/write slave device meeting all Philips I 2 C-bus speciications except a general call. The bus has to be controlled by a master device that generates the serial clock SCL, controls bus access, and generates the START and STOP conditions while the device works as a slave. Both master and slave can operate as a transmitter or receiver, but the master device determines which mode is activated. A device that sends data onto the bus is deined as the transmitter, and a device receiving data as the receiver. I 2 C-bus logic levels noted herein are based on a percentage o the power supply (V DD. A logic-one corresponds to a nominal voltage o V DD, while a logic-zero corresponds to ground (V SS. 5. Bus Conditions Data transer on the bus can only be initiated when the bus is not busy. During the data transer, the data line (SDA must remain stable whenever the clock line (SCL is high. Changes in the data line while the clock line is high will be interpreted by the device as a START or STOP condition. The ollowing bus conditions are deined by the I 2 C-bus protocol. 5.. Not Busy Both the data (SDA and clock (SCL lines remain high to indicate the bus is not busy START Data Transer A high to low transition o the SDA line while the SCL input is high indicates a START condition. All commands to the device must be preceded by a START condition STOP Data Transer A low to high transition o the SDA line while SCL is held high indicates a STOP condition. All commands to the device must be ollowed by a STOP condition Data Valid The state o the SDA line represents valid data i the SDA line is stable or the duration o the high period o the SCL line ater a START condition occurs. The data on the SDA line must be changed only during the low period o the SCL signal. There is one clock pulse per data bit. Each data transer is initiated by a START condition and terminated with a STOP condition. The number o data bytes transerred between START and STOP conditions is determined by the master device, and can continue indeinitely. However, data that is overwritten to the device ater the irst eight bytes will overlow into the irst register, then the second, and so on, in a irst-in, irstoverwritten ashion Acknowledge When addressed, the receiving device is required to generate an Acknowledge ater each byte is received. The master device must generate an extra clock pulse to coincide with the Acknowledge bit. The acknowledging device must pull the SDA line low during the high period o the master acknowledge clock pulse. Setup and hold times must be taken into account. The master must signal an end o data to the slave by not generating and acknowledge bit on the last byte that has been read (clocked out o the slave. In this case, the slave must leave the SDA line high to enable the master to generate a STOP condition. 5.2 I 2 C-bus Operation All programmable registers can be accessed randomly or sequentially via this bi-directional two wire digital interace. The crystal oscillator does not have to run or communication to occur. The device accepts the ollowing I 2 C-bus commands: 5.2. Slave Address Ater generating a START condition, the bus master broadcasts a seven-bit slave address ollowed by a R/W bit. The address o the device is: A6 A5 A4 A3 A2 A A0 0 X 0 0 where X is controlled by the logic level at the ADDR pin. The variable ADDR bit allows two dierent FS63 devices to exist on the same bus. Note that every device on an I 2 C-bus must have a unique address to avoid bus conlicts. The deault address sets A2 to 0 via the pulldown on the ADDR pin. 9

10 5.2.2 Random Register Write Procedure Random write operations allow the master to directly write to any register. To initiate a write procedure, the R/W bit that is transmitted ater the seven-bit device address is a logic-low. This indicates to the addressed slave device that a register address will ollow ater the slave device acknowledges its device address. The register address is written into the slave s address pointer. Following an acknowledge by the slave, the master is allowed to write eight bits o data into the addressed register. A inal acknowledge is returned by the device, and the master generates a STOP condition. I either a STOP or a repeated START condition occurs during a Register Write, the data that has been transerred is ignored Random Register Read Procedure Random read operations allow the master to directly read rom any register. To perorm a read procedure, the R/W bit that is transmitted ater the seven-bit address is a logic-low, as in the Register Write procedure. This indicates to the addressed slave device that a register address will ollow ater the slave device acknowledges its device address. The register address is then written into the slave s address pointer. Following an acknowledge by the slave, the master generates a repeated START condition. The repeated START terminates the write procedure, but not until ater the slave s address pointer is set. The slave address is then resent, with the R/W bit set this time to a logic-high, indicating to the slave that data will be read. The slave will acknowledge the device address, and then transmits the eight-bit word. The master does not acknowledge the transer but does generate a STOP condition Sequential Register Write Procedure Sequential write operations allow the master to write to each register in order. The register pointer is automatically incremented ater each write. This procedure is more eicient than the Random Register Write i several registers must be written. To initiate a write procedure, the R/W bit that is transmitted ater the seven-bit device address is a logic-low. This indicates to the addressed slave device that a register address will ollow ater the slave device acknowledges its device address. The register address is written into the slave s address pointer. Following an acknowledge by the slave, the master is allowed to write up to eight bytes o data into the addressed register beore the register address pointer overlows back to the beginning address. An acknowledge by the device between each byte o data must occur beore the next data byte is sent. Registers are updated every time the device sends an acknowledge to the host. The register update does not wait or the STOP condition to occur. Registers are thereore updated at dierent times during a Sequential Register Write Sequential Register Read Procedure Sequential read operations allow the master to read rom each register in order. The register pointer is automatically incremented by one ater each read. This procedure is more eicient than the Random Register Read i several registers must be read. To perorm a read procedure, the R/W bit that is transmitted ater the seven-bit address is a logic-low, as in the Register Write procedure. This indicates to the addressed slave device that a register address will ollow ater the slave device acknowledges its device address. The register address is then written into the slave s address pointer. Following an acknowledge by the slave, the master generates a repeated START condition. The repeated START terminates the write procedure, but not until ater the slave s address pointer is set. The slave address is then resent, with the R/W bit set this time to a logic-high, indicating to the slave that data will be read. The slave will acknowledge the device address, and then transmits all eight bytes o data starting with the initial addressed register. The register address pointer will overlow i the initial register address is larger than zero. Ater the last byte o data, the master does not acknowledge the transer but does generate a STOP condition. 0

11 Figure 3: Random Register Write Procedure S DEVICE ADDRESS W A REGISTER ADDRESS A DATA A P 7-bit Receive Device Address START Command Register Address Acknowledge WRITE Command From bus host to device Data Acknowledge From device to bus host STOP Condition Acknowledge Figure 4: Random Register Read Procedure S DEVICE ADDRESS W A REGISTER ADDRESS A S DEVICE ADDRESS R A DATA A P 7-bit Receive Device Address START Command Register Address Acknowledge WRITE Command From bus host to device 7-bit Receive Device Address Repeat START Acknowledge From device to bus host Data Acknowledge READ Command STOP Condition NO Acknowledge Figure 5: Sequential Register Write Procedure S DEVICE ADDRESS W A REGISTER ADDRESS A DATA A DATA A DATA A P 7-bit Receive Device Address START Command Register Address Acknowledge WRITE Command From bus host to device Data Acknowledge From device to bus host Data Acknowledge Acknowledge Data Acknowledge STOP Command Figure 6: Sequential Register Read Procedure S DEVICE ADDRESS W A REGISTER ADDRESS A S DEVICE ADDRESS R A DATA A DATA A P 7-bit Receive Device Address START Command Register Address Acknowledge WRITE Command From bus host to device 7-bit Receive Device Address Repeat START Acknowledge From device to bus host Data Acknowledge READ Command Acknowledge Data NO Acknowledge STOP Command

12 6.0 Programming Inormation All register bits are cleared to zero on power-up. All register bits may be read back as written except STAT[] (Bit 63. Table 3: Register Map ADDRESS BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT BIT 0 BYTE 7 BYTE 6 BYTE 5 BYTE 4 BYTE 3 STAT[] (Bit 63 STAT[0] (Bit = Crystal Loop Lock Status 0 = Crystal Loop Out o Range 0 = Main Loop Phase Status = Feedback Divider Output XLPDEN (Bit 55 0 = Crystal Loop Operates = Crystal Loop Powered Down OUTMUX[] (Bit 47 XLSWAP (Bit 54 0 = Use with External VCXO = Use with Internal VCXO OUTMUX[0] (Bit 46 XLVTEN (Bit 6 0 = Fine Tune Inactive = Fine Tune Active XLCP[] (Bit 53 OSCTYPE (Bit =.5µA 0 = 5µA 0 = 8µA = 24µA CMOS (Bit 60 0 = PECL = CMOS, Lock Status XLCP[0] (Bit 52 VCOSPD (Bit 44 XCT[3] (Bit 59 XLROM[2] (Bit 5 LFTC (Bit 43 XCT[2] (Bit 58 XLROM[] (Bit 50 Crystal Loop Control See Table 0 EXTLF (Bit 42 VCXO Coarse Tune See Table XCT[] (Bit 57 XLROM[0] (Bit 49 MLCP[] (Bit 4 00 = VCO Output 0 = Low Phase 0 = High Speed 0 = Short Time 0 = Internal Loop 00 =.5µA 0 = Reerence Divider Output Jitter Oscillator Range Constant Filter 0 = 5µA 0 = Phase Detector Input = FS603 = Low Speed = Long Time = External Loop 0 = 8µA = VCXO Output Oscillator Range Constant Filter = 24µA FBKDSRC[] (Bit 39 FBKDSRC[0] (Bit = Post Divider Output FBKDIV[7] (Bit 3 0 = FBK Pin 0 = Post Divider Input = FBK Pin FBKDIV[6] (Bit 30 FBKDIV[3] (Bit 37 FBKDIV[2] (Bit 36 FBKDIV[] (Bit 35 FBKDIV[0] (Bit 34 FBKDIV[9] (Bit 33 XCT[0] (Bit 56 GBL (Bit 48 0 = No Clock Phase Adjust = Clock Phase Delay MLCP[0] (Bit 40 FBKDIV[8] (Bit FBKDIV[5] (Bit 29 FBKDIV[4] (Bit 28 FBKDIV[3] (Bit 27 M Counter FBKDIV[2] (Bit 26 FBKDIV[] (Bit BYTE 2 Reserved (0 Reserved (0 BYTE BYTE 0 PDFBK (Bit 5 0 = Feedback Divider PDREF (Bit 4 0 = Reerence Divider = FBK Pin = REF Pin REFDIV[7] (Bit 7 REFDIV[6] (Bit 6 M Counter A Counter See Table 2 POST3[] (Bit 2 SHUT (Bit 3 0 = Main Loop Operates = Main Loop Powered Down REFDIV[5] (Bit 5 POST3[] (Bit 20 POST2[] (Bit 9 POST2[0] (Bit 8 POST[] (Bit 7 00 = Divide by 00 = Divide by 00 = Divide by 0 = Divide by 3 0 = Divide by 3 0 = Divide by 2 0 = Divide by 5 0 = Divide by 5 0 = Divide by 4 = Divide by 4 = Divide by 4 = Divide by 8 REFDSRC (Bit 2 0 = VCXO = Re Pin REFDIV[4] (Bit 4 REFDIV[] (Bit REFDIV[0] (Bit 0 REFDIV[9] (Bit 9 FBKDIV[0] (Bit 24 POST[0] (Bit 6 REFDIV[8] (Bit REFDIV[3] (Bit 3 REFDIV[2] (Bit 2 REFDIV[] (Bit REFDIV[0] (Bit

13 Table 4: Device Coniguration Bits Table 5: LOCK/IPRG Pin Coniguration Bits NAME DESCRIPTION NAME DESCRIPTION REFDSRC (Bit 2 SHUT (Bit 3 PDREF (Bit 4 PDFBK (Bit 5 FBKDSRC[:0] (Bits EXTLF (Bit 42 OSCTYPE (Bit 45 OUTMUX[:0] (Bits GBL (Bit 48 CMOS (Bit 60 REFerence Divider SouRCe Bit = 0 Crystal Oscillator (VCXO Bit = REF pin main loop SHUT down select Bit = 0 Disabled (main loop operates Bit = Enabled (main loop shuts down Phase Detector REFerence source Bit = 0 Reerence Divider Bit = REF pin Phase Detector FeedBacK source Bit = 0 Feedback Divider Bit = FBK pin FeedBacK Divider SouRCe Bit 39 = 0 Bit 38 = 0 Post Divider Output Bit 39 = 0 Bit 38 = Bit 39 = Bit 38 = 0 Bit 39 = Bit 38 = FBK pin VCO Output (Post Divider Input FBK pin EXTernal Loop Filter select Bit = 0 Internal Loop Filter Bit = EXTLF pin OSCillator TYPe Bit = 0 Low Phase Jitter Oscillator Bit = FS603 Compatible Oscillator OUTput MUltipleXer select Bit 47 = 0 Bit 46 = 0 Main Loop PLL (VCO Output Bit 47 = 0 Bit 46 = Bit 47 = Bit 46 = 0 Bit 47 = Bit 46 = Reerence Divider Output Phase Detector Input VCXO Output clock GobBLer control Bit = 0 No Clock Phase Adjust Bit = Clock Phase Delay CLKP/CLKN output mode Bit = 0 Bit = PECL Output (positive-ecl output drive CMOS Output / Lock Status Indicator STAT[:0] (Bits crystal loop lock STATus mode / main loop phase align STATus mode (see also Table 6 Bit 63 = 0 Bit 62 = 0 Bit 63 = 0 Bit 62 = Bit 63 = Bit 62 = 0 Bit 63 = Bit 62 = Table 6: Lock Status CMOS STAT [] STAT [0] LOCK / IPRG PIN Crystal Loop Lock status: Locked or Unlocked Crystal Loop Lock status: Out o Range High or Low Main Loop Phase Align status Feedback Divider output STAT[] READ STATUS Locked 0 0 Unlocked 0 0 Table 7: Main Loop Tuning Bits NAME VCOSPD (Bit 44 MLCP[:0] (Bits 4-40 LFTC (Bit 43 DESCRIPTION VCO SPeeD range select (see Table 6 Bit = 0 High Speed Range Bit = Low Speed Range Main Loop Charge Pump current Bit 4 = 0 Bit 40 = 0 Current =.5µA Bit 4 = 0 Bit 40 = Bit 4 = Bit 40 = 0 Bit 4 = Bit 40 = Current = 5µA Current = 8µA Current = 24µA Loop Filter Time Constant (internal Out-o- Range: Low Out-o- Range: High Bit = 0 Short Time Constant: 3.5µs Bit = Long Time Constant: 35µs 3

14 Table 8: Divider Control Bits Table 9: Crystal Loop Tuning Bits NAME DESCRIPTION NAME DESCRIPTION REFDIV[:0] (Bits -0 FBKDIV[3:0] (Bits POST[:0] (Bits 7-6 POST2[:0] (Bits 9-8 POST3[:0] (Bits 2-20 Reserved (0 (Bits REFerence DIVider (N R FeedBacK DIVider (N F FBKDIV[2:0] A-Counter Value FBKDIV[3:3] M-Counter Value POST Divider # (N P Bit 7 = 0 Bit 6 = 0 Divide by Bit 7 = 0 Bit 6 = Bit 7 = Bit 6 = 0 Bit 7 = Bit 6 = POST Divider #2 (N P2 Bit 9 = 0 Bit 8 = 0 Bit 9 = 0 Bit 8 = Bit 9 = Bit 8 = 0 Bit 9 = Bit 8 = POST Divider #3 (N P3 Bit 2 = 0 Bit 20 = 0 Bit 2 = 0 Bit 20 = Bit 2 = Bit 20 = 0 Bit 2 = Bit 20 = Divide by 2 Divide by 4 Divide by 8 Divide by Divide by 3 Divide by 5 Divide by 4 Divide by Divide by 3 Divide by 5 Divide by 4 Set these reserved bits to 0 XLCP[:0] (Bits XLROM[2:0] (Bits 5-49 XLVTEN (Bit 6 XLSWAP (Bit 54 XLPDEN (Bit 55 XCT[3:0] (Bits Crystal Loop Charge Pump current Bit 53 = 0 Bit 52 = 0 Bit 53 = 0 Bit 52 = Bit 53 = Bit 52 = 0 Bit 53 = Bit 52 = Current =.5µA Current = 5µA Current = 8µA Current = 24µA Crystal Loop Divider ROM select and Crystal Oscillator Power-Down (see Table 0 Crystal Loop Voltage ine Tune ENable Bit = 0 Disabled (ine tune is inactive Bit = Enabled (ine tune is active Crystal Loop SWAP polarity Bit = 0 Use with an external VCXO that increases in requency in response to an increasing voltage at the XTUNE pin. Use with a VCXO that increases in requency in response to a decreasing voltage at the XTUNE Bit = pin. Use this setting or Internal VCXO Crystal Loop Power Down Enable Bit = 0 Disabled (crystal loop operates Bit = Enabled (crystal loop is powered down Crystal Coarse Tune (see Table Table 0: Crystal Loop Control ROM XLROM [2] XLROM [] XLROM [0] VCXO DIVIDER CRYSTAL FREQUENCY (MHz Crystal Oscillator Power-Down 4

15 6. VCXO Coarse Tune The VCXO may be coarse tuned by a programmable adjustment o the crystal load capacitance via XCT[3:0]. The actual amount o requency warping caused by the tuning capacitance will depend on the crystal used. The VCXO tuning capacitance includes an external 6pF load capacitance (2pF rom the XIN pin to ground and 2pF rom the XOUT pin to ground. The ine tuning capability o the VCXO can be enabled by setting the XLVTEN bit to a logic-one, or disabled by setting the bit to a logiczero. Table : VCXO Coarse Tuning Capacitance XCT[3] XCT[2] XCT[] XCT[0] VCXO TUNING CAPACITANCE (pf

16 7.0 Electrical Speciications Table 2: Absolute Maximum Ratings Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These conditions represent a stress rating only, and unctional operation o the device at these or any other conditions above the operational limits noted in this speciication is not implied. Exposure to maximum rating conditions or extended conditions may aect device perormance, unctionality, and reliability. PARAMETER SYMBOL MIN. MAX. UNITS Supply Voltage, dc (V SS = ground V DD V SS V Input Voltage, dc V I V SS-0.5 V DD+0.5 V Output Voltage, dc V O V SS-0.5 V DD+0.5 V Input Clamp Current, dc (V I < 0 or V I > V DD I IK ma Output Clamp Current, dc (V I < 0 or V I > V DD I OK ma Storage Temperature Range (non-condensing T S C Ambient Temperature Range, Under Bias T A C Junction Temperature T J 50 C Lead Temperature (soldering, 0s 260 C Input Static Discharge Voltage Protection (MIL-STD 883E, Method kv CAUTION: ELECTROSTATIC SENSITIVE DEVICE Permanent damage resulting in a loss o unctionality or perormance may occur i this device is subjected to a high-energy electrostatic discharge. Table 3: Operating Conditions PARAMETER SYMBOL CONDITIONS/DESCRIPTION MIN. TYP. MAX. UNITS Supply Voltage V DD 5V ± 0% V Ambient Operating Temperature Range T A 0 70 C Crystal Resonator Frequency XIN MHz Crystal Resonator Load Capacitance C XL Parallel resonant, AT cut 8 pf Crystal Resonator Motional Capacitance C XM Parallel resonant, AT cut 25 F Serial Data Transer Rate Standard mode kb/s PECL Mode Programming Current (LOCK/IPRG Pin High-Level Input Current I IH PECL Mode 5 ma Output Driver Load Capacitance C L 5 pf 6

17 Table 4: DC Electrical Speciications Unless otherwise stated, VDD = 5.0V ± 0%, no load on any output, and ambient temperature range TA = 0 C to 70 C. Parameters denoted with an asterisk ( * represent nominal characterization data and are not production tested to any speciic limits. MIN and MAX characterization data are ± 3σ rom typical. Negative currents indicate current lows out o the device. Overall Supply Current, Dynamic, (with Loaded Outputs PARAMETER SYMBOL CONDITIONS/DESCRIPTION MIN. TYP. MAX. UNITS I DD CLK = 66MHz; CMOS Mode, V DD = 5.5V 00 ma Supply Current, Static I DDL SHUT =, XLROM[2:0] = 7, XLPDEN = V DD = 5.5V Serial Communication I/O (SDA, SCL 7 2 ma High-Level Input Voltage V IH Outputs o 3.5 V DD+0.3 V Low-Level Input Voltage V IL Outputs o V SS V Hysteresis Voltage * V hys Outputs o 2 V Input Leakage Current I I - µa Low-Level Output Sink Current (SDA I OL V OL = 0.4V ma Tristate Output Current I Z -0 0 µa Address Select Input (ADDR High-Level Input Voltage V IH 2.4 V DD+0.3 V Low-Level Input Voltage V IL V SS V High-Level Input Current (pull-down I IH V IH = V DD = 5.5V µa Low-Level Input Current I IL -2 2 µa Reerence Frequency Input (REF, FBK High-Level Input Voltage V IH 3.5 V DD+0.3 V Low-Level Input Voltage V IL V SS V Hysteresis Voltage V hys 500 mv Input Leakage Current I I - µa Loop Filter Input (EXTLF Input Leakage Current I I EXTLF = 0 - µa High-Level Output Source Current Low-Level Output Sink Current Crystal Oscillator Input (XIN I OH I OL V O = 0.8V; EXTLF =, MLCP[:0] = V O = 0.8V; EXTLF =, MLCP[:0] = -5 V O = 0.8V; EXTLF =, MLCP[:0] = 2-8 V O = 0.8V; EXTLF =, MLCP[:0] = 3-24 V O = 4.2V; EXTLF =, MLCP[:0] = 0.5 V O = 4.2V; EXTLF =, MLCP[:0] = 5 V O = 4.2V; EXTLF =, MLCP[:0] = 2 8 V O = 4.2V; EXTLF =, MLCP[:0] = 3 25 Threshold Bias Voltage V TH V High-Level Input Current I IH Outputs o; V IH = 5V ma Low-Level Input Current I IL Outputs o; V IL = 0V ma Crystal Loading Capacitance * C L(xtal As seen by an external crystal connected to XIN and XOUT; VCXO tuning disabled Input Loading Capacitance * C L(XIN As seen by an external clock driver on XOUT; XIN unconnected; VCXO disabled µa µa 0 pf 20 pf

18 Table 5: DC Electrical Speciications, continued Unless otherwise stated, VDD = 5.0V ± 0%, no load on any output, and ambient temperature range TA = 0 C to 70 C. Parameters denoted with an asterisk ( * represent nominal characterization data and are not production tested to any speciic limits. MIN and MAX characterization data are ± 3σ rom typical. Negative currents indicate current lows out o the device. PARAMETER SYMBOL CONDITIONS/DESCRIPTION MIN. TYP. MAX. UNITS Crystal Oscillator Output (XOUT High-Level Output Source Current I OH V O = 0V, loat XIN ma Low-Level Output Sink Current I OL V O = 5V, loat XIN ma VCXO Tuning I/O (XTUNE High-Level Input Voltage V IH Lock Status: Out o Range HIGH 3.2 V DD+0.3 V Low-Level Input Voltage V IL Lock Status: Out o Range LOW V SS V Hysteresis Voltage V hys.0 V Input Leakage Current I I XLPDEN = 0 - µa High-Level Output Source Current Low-Level Output Sink Current Lock Indicator / PECL Current Program I/O (LOCK/IPRG I OH I OL V O = 0.8V; XLCP[:0] = V O = 0.8V; XLCP[:0] = -5 V O = 0.8V; XLCP[:0] = 2-8 V O = 0.8V; XLCP[:0] = 3-24 V O = 4.2V; XLCP[:0] = 0.5 V O = 4.2V; XLCP[:0] = 5 V O = 4.2V; XLCP[:0] = 2 8 V O = 4.2V; XLCP[:0] = 3 25 Low-Level Input Current I IL PECL Mode - µa High-Level Output Source Current I OH CMOS Mode; V O = 2.4V ma Low-Level Output Sink Current I OL CMOS Mode; V O = 0.4V 5 9 ma Output Impedance * z OH V O = 0.5V DD; output driving high 66 z OL V O = 0.5V DD; output driving low 76 Short Circuit Source Current * I SCH V O = 0V; shorted or 30s, max. -47 ma Short Circuit Sink Current * I SCL V O = 5V; shorted or 30s, max. 47 ma Clock Outputs, CMOS Mode (CLKN, CLKP High-Level Output Source Current I OH V O = 2.4V ma Low-Level Output Sink Current I OL V O = 0.4V 5 20 ma Output Impedance * z OH V O = 0.5V DD; output driving high 28 z OL V O = 0.5V DD; output driving low 33 Short Circuit Source Current * I SCH V O = 0V; shorted or 30s, max. -00 ma Short Circuit Sink Current * I SCL V O = 5V; shorted or 30s, max. 00 ma Clock Outputs, PECL Mode (CLKN, CLKP IPRG Current to Output Current Ratio :4 Low-Level Output Sink Current I OL IPRG input current = 5mA 60 ma Tristate Output Current I Z -0 0 µa µa µa Ω Ω 8

19 Table 6: AC Timing Speciications Unless otherwise stated, VDD = 5.0V ± 0%, no load on any output, and ambient temperature range TA = 0 C to 70 C. Parameters denoted with an asterisk ( * represent nominal characterization data and are not production tested to any speciic limits. MIN and MAX characterization data are ± 3σ rom typical. PARAMETER SYMBOL CONDITIONS/DESCRIPTION CLOCK (MHz MIN. TYP. MAX. UNITS Overall CMOS Outputs 30 Output Frequency * O(max PECL Outputs 230 MHz VCO Frequency * VCO Gain * Loop Filter Time Constant * VCO A VCO Low Phase Jitter Oscillator (OSCTYPE = 0 VCOSPD = VCOSPD = FS603 Compatible Oscillator (OSCTYPE = VCOSPD = VCOSPD = Low Phase Jitter Oscillator (OSCTYPE = 0 VCOSPD = 0 25 VCOSPD = 75 FS603 Compatible Oscillator (OSCTYPE = VCOSPD = 0 30 VCOSPD = 78 LFTC = LFTC = 35 Rise Time * t r CMOS Outputs, V O = 0.5V to 4.5V; C L = 5pF. ns Fall Time * t CMOS Outputs, V O = 4.5V to 0.5V; C L = 5pF 0.8 ns Lock Time (Main Loop * Disable Time * Divider Modulus Frequency Synthesis 200 µs MHz MHz/V Line Locked Modes (8kHz reerence 0 ms From alling edge o SCL or the last data bit (SHUT = to 0 to output locked µs 0 µs Feedback Divider N F FBKDIV[3:0] (See also Table Reerence Divider N R REFDIV[:0] 4095 Post Divider N P POST[:0] (See also Table 8 8 N P2 POST2[:0] (See also Table 8 5 N P3 POST3[:0] (See also Table 8 5 9

20 Table 7: AC Timing Speciications, continued Unless otherwise stated, VDD = 5.0V ± 0%, no load on any output, and ambient temperature range TA = 0 C to 70 C. Parameters denoted with an asterisk ( * represent nominal characterization data at TA = 27 C and are not production tested to any speciic limits. MIN and MAX characterization data are ± 3σ rom typical. PARAMETER SYMBOL CONDITIONS/DESCRIPTION CLOCK (MHz MIN. TYP. MAX. UNITS Clock Output (CLKP, CLKN Duty Cycle * Jitter, Long Term (σ y(τ * Jitter, Period (peak-peak * t j(lt t j( P Ratio o pulse width (as measured rom rising edge to next alling edge at 2.5V to one clock period % Rising edges 50ms apart at 2.5V, relative to an ideal clock, CL=5pF, REF=8kHz, NR=, NF=93, NPx=64, CLF=0.054µF, RLF=5.7kΩ, CLP=800pF, OSCTYPE=0, MLCP=3, XLROM=7 Rising edges 50ms apart at 2.5V, relative to an ideal clock, CL=5pF, REF=5kHz, NR=, NF=800, NPx=0, CLF=0.0246µF, RLF=5.7kΩ, CLP=820pF, OSCTYPE=0, MLCP=3, XLROM=7 On rising edges 5ms apart at 2.5V relative to an ideal clock, CL=5pF, REF=3.5kHz, NR=, NF=799, NPx=4, CLF=0.05µF, RLF=5.7kΩ, CLP=470pF, OSCTYPE=0, MLCP=3, XLROM= On rising edges 500µs apart at 2.5V relative to an ideal clock, CL=5pF, CMOS mode, XIN=27MHz, NF=200, NR=27, NPx= On rising edges 500µs apart at 2.5V relative to an ideal clock, CL=5pF, PECL mode, XIN=27MHz, NF=200, NR=27, NPx= From rising edge to next rising edge at 2.5V, CL=5pF, REF=8kHz, NR=, NF=93, NPx=64, CLF=0.054µF, RLF=5.7kΩ, CLP=800pF, OSCTYPE=0, MLCP=3, XLROM=7 From rising edge to next rising edge at 2.5V, CL=5pF, REF=5kHz, NR=, NF=800, NPx=0, CLF=0.0246µF, RLF=5.7kΩ, CLP=820pF, OSCTYPE=0, MLCP=3, XLROM=7 From rising edge to next rising edge at 2.5V, CL=5pF, REF=3.5kHz, NR=, NF=799, NPx=4, CLF=0.05µF, RLF=5.7kΩ, CLP=470pF, OSCTYPE=0, MLCP=3, XLROM= From rising edge to next rising edge at 2.5V, CL=5pF, CMOS mode, XIN=27MHz, NF=200, NR=27, NPx= From rising edge to next rising edge at 2.5V, CL=5pF, PECL mode, XIN=27MHz, NF=200, NR=27, NPx= ps ps 20

21 Table 8: Serial Interace Timing Speciications Unless otherwise stated, VDD = 5.0V ± 0%, no load on any output, and ambient temperature range TA = 0 C to 70 C. Parameters denoted with an asterisk ( * represent nominal characterization data and are not production tested to any speciic limits. MIN and MAX characterization data are ± 3σ rom typical. PARAMETER SYMBOL CONDITIONS/DESCRIPTION STANDARD MODE Clock requency SCL SCL khz Bus ree time between STOP and START t BUF 4.7 µs Set up time, START (repeated t su:sta 4.7 µs Hold time, START t hd:sta 4.0 µs Set up time, data input t su:dat SDA 250 ns Hold time, data input t hd:dat SDA 0 µs Output data valid rom clock t AA Minimum delay to bridge undeined region o the alling edge o SCL to avoid unintended START or STOP 3.5 µs Rise time, data and clock t R SDA, SCL 000 ns Fall time, data and clock t F SDA, SCL 300 ns High time, clock t HI SCL 4.0 µs Low time, clock t LO SCL 4.7 µs Set up time, STOP t su:sto 4.0 µs MIN. MAX. UNITS Figure 7: Bus Timing Data ~ SCL t su:sta t hd:sta ~ t su:sto SDA START ADDRESS OR DATA VALID DATA CAN CHANGE ~ STOP Figure 8: Data Transer Sequence t F t HI t R ~ SCL t su:sta t LO t hd:sta t su:dat~ t su:sto t hd:dat SDA IN ~ ~ t BUF t AA t AA SDA OUT 2

22 Table 9: CLKP, CLKN Clock Outputs (CMOS Mode Voltage (V Low Drive Current (ma MIN. TYP. MAX. Voltage (V High Drive Current (ma MIN. TYP. MAX Output Current (ma MIN -200 TYP Output Voltage (V MAX The data in this table represents nominal characterization data only. Table 20: LOCK/IPRG Clock Output (CMOS Mode Voltage (V Low Drive Current (ma MIN. TYP. MAX. Voltage (V High Drive Current (ma MIN. TYP. MAX Output Current (ma MIN -80 TYP Output Voltage (V MAX The data in this table represents nominal characterization data only. 22

23 R FS Package Inormation Table 2: 6-pin SOIC (0.50" Package Dimensions DIMENSIONS 6 INCHES MILLIMETERS MIN. MAX. MIN. MAX. A A A AMERICAN MICROSYSTEMS, INC. E H B C D E B e ALL RADII: 0.005" TO 0.0" h x 45 7 typ. e BSC.27 BSC H A 2 A C h L Θ BASE PLANE D A SEATING PLANE L θ Table 22: 6-pin SOIC (0.50" Package Characteristics PARAMETER SYMBOL CONDITIONS/DESCRIPTION TYP. UNITS Thermal Impedance, Junction to Free-Air Θ JA Air low = 0 t./min. 08 C/W Corner lead 4.0 Lead Inductance, Sel L Center lead 3.0 Lead Inductance, Mutual L 2 Any lead to any adjacent lead 0.4 nh Lead Capacitance, Bulk C Any lead to V SS 0.5 pf nh 23

24 9.0 Ordering Inormation 9. Device Ordering Codes ORDERING CODE DEVICE NUMBER FONT PACKAGE TYPE OPERATING TEMPERATURE RANGE SHIPPING CONFIGURATION FS FS FS63-0i FS63-0i 6-pin (0.50 SOIC (Small Outline Package 6-pin (0.50 SOIC (Small Outline Package 6-pin (0.50 SOIC (Small Outline Package 6-pin (0.50 SOIC (Small Outline Package 0 C to 70 C (Commercial Tape-and-Reel 0 C to 70 C (Commercial Tubes -40 C to 85 C (Industrial Tape-and-Reel -40 C to 85 C (Industrial Tubes 9.2 Demo Kit Ordering Codes ORDERING CODE KIT FOR DEVICE NUMBER: DESCRIPTION FS63-0 Kit includes: Populated board with example device Interace Cable Programming Assistance PC Sotware Purchase o I 2 C components o American Microsystems, Inc., or one o its sublicensed Associated Companies conveys a license under Philips I 2 C Patent Rights to use these components in an I 2 C system, provided that the system conorms to the I 2 C Standard Speciication as deined by Philips. Copyright 998, 999 American Microsystems, Inc. Devices sold by AMI are covered by the warranty and patent indemniication provisions appearing in its Terms o Sale only. AMI makes no warranty, express, statutory implied or by description, regarding the inormation set orth herein or regarding the reedom o the described devices rom patent inringement. AMI makes no warranty o merchantability or itness or any purposes. AMI reserves the right to discontinue production and change speciications and prices at any time and without notice. AMI s products are intended or use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical lie-support or lie-sustaining equipment, are speciically not recommended without additional processing by AMI or such applications. American Microsystems, Inc., 2300 Buckskin Rd., Pocatello, ID 8320, ( , FAX ( , WWW Address: tgp@amis.com 24

25 0.0 Demonstration Board and Sotware A simple demonstration board and Windows 3.x/95/98-based sotware is available rom American Microsystems that illustrates the capabilities o the FS63. The sotware can operate under Windows NT but cannot communicate with the board. The board schematic is shown below. Components listed with an asterisk (* are not required in an actual application, and are used here to preserve signal integrity with the cabling associated with the board. A cabled interace between a computer parallel port (DB25 connector and the board (J is provided. Components shown in dashed lines are optional, depending on the application. Contact your local sales representative or more inormation. Figure 9: Board Schematic J* SCL 2 SDA 3 ADDR R* 00 R2* 00 R3* 00 R5 0 +5V 4 5 C2 2.2µF C4 0.µF +5V +5V 6 R2 R4 +5V GND RP k +5V +5V C8 2pF Y 27MHz R6 C9 2pF SCL CLKN SDA CLKP ADDR VDD VSS FBK FS63 XIN REF XOUT VSS XTUNE EXTLF VDD LOCK/ IPRG R9 R3 R6 47 R7 47 R5 R8 CLKN CLKP FBK REF R9 C0 C C 2.2µF C3 0.µF +5V R4 0 R8 R7 LOCK C6 C7 AMERICAN MICROSYSTEMS, INC. FS63 DEMO BOARD 25

26 0. Demo Kit Contents Demonstration board Interace cable (DB25 to 6-pin connector Data sheet Programming sotware 0.2 Requirements PC running MS Windows 3.x or 95/98 with an accessible parallel (LPT port. Sotware also runs on Windows NT in a calculation mode only. 2.0MB available space on hard drive C: 0.3 Board Setup and Sotware Installation Instructions. Run the sel-expanding exe ile to unzip the compressed demo iles to a directory o your choice. 2. Run the setup.exe ile to install the programming sotware. 3. Connect a +5 Volt power supply to the board: RED = +5V, BLACK = ground. 4. Remove all sotware keys rom the computer parallel port. Connect the supplied interace cable to the parallel port (DB25 connector and to the demo board (6- pin connector. Make sure the cable is acing away rom the board. Pin is the red wire per Figure Connect the clock outputs to the target application board with a twisted-pair cable. 0.4 Demo Program Operation Run the s63.exe program. Note that the parallel port can not be accessed i your machine is running Windows NT. A warning message will appear stating: This version o the demo program cannot communicate with the FS63 hardware when running on a Windows NT operating system. Do you want to continue anyway, using just the calculation eatures o this program? Clicking OK starts the program or calculation only. The opening screen is shown in Figure 20. Figure 20: Opening Screen 26

27 0.4. Device Mode The Device Mode block presets the demo program to program the FS63 either as a requency synthesizer (a stand alone clock generator or as a line-locked or genlock clock generator. Frequency Synthesis: For use as a stand alone clock generator. Note that the Reerence Source is the on-chip crystal oscillator, the expected crystal requency is 27MHz, and the Voltage Tune in the Crystal Oscillator (i.e. the VCXO is disabled. The deault output requency (CLK req. requested is 00MHz, with a maximum error o 0ppm, or about 00Hz. The Output Stage deaults to CMOS mode. Line-Locked/Genlock: For use in a line lock or genlock application. Note that the Reerence Source is the REF Pin, and that the expected reerence requency is 8kHz. The deault output requency requested is a 00x multiple o the reerence requency Example: Frequency Synthesizer Mode By deault the demo program assumes the FS63 is conigured as a stand alone clock generator. Note that the Reerence Source deaults to the on-chip crystal oscillator, the expected crystal requency is 27MHz, and the Voltage Tune in the Crystal Oscillator block (i.e. the VCXO is disabled. The deault output requency (CLK req. requested is 00MHz, with a maximum error o 0ppm, or about 00Hz. The Output Stage deaults to CMOS mode. The Loop Filter block is set to internal, and the Check Loop Stability switch is on. As an exercise, click on Calculate Solutions. The program takes into account all o the screen settings and calculates all possible combinations o Reerence, Feedback, and Post Divider values that will generate the output requency (00MHz rom the input requency (27MHz within the desired tolerance (0ppm. A box will momentarily appear: Calculating Solutions: Press cancel to stop with the solutions calculated so ar. A number in the box will increment or every unique solution that is ound. This example will create six unique solutions, which are then displayed in a window in the lower right portion o the program screen. The best PLL perormance is obtained by running the VCO at as high a speed as possible. The last three solutions show a VCO speed o 200MHz. Furthermore, good PLL perormance is obtained with the smallest dividers possible, which means solution #4 should provide the best results. Figure 2: Frequency Synthesizer Screen Clicking on Solution #4 highlights the row, and clicking on Disp/Save Register Values provides a window with the inal values o key settings. A click on OK then displays a second window containing register inormation per the Register Map. I the solutions are to be saved to a ile, two ormats are available: a text ormat or viewing, and a data ormat or loading into the FS63. Clicking on Load Solution into Hardware (i enabled sends the inormation in an I 2 C ormat to the FS63 via the parallel port. Note: This option is not available under the Windows NT operating system. I your operating system can support parallel port communication but the connection cable is not attached, an error message is displayed: "The FS63 Hardware was not detected! "Make sure that it is connected to the LPT# printer port and that it is properly connected to a +5Volt power supply." 27

28 0.4.3 Example: Line Locked Mode Selecting the Line-Locked/Genlock option in the Device Mode block changes the program deault settings. The Reerence Source changes to the REF Pin input, and a block appears to permit entry o the REF input requency in MHz. A Desired Multiple block allows entry o the reerence requency multiplying actor used to generate the output requency. Exercise: Change the Re Pin Frequency to 0.035MHz, and alter the Desired Multiple to 800. Change the Loop Filter block to external, but leave the values or C and R alone. Click on Calculate Solutions. The program takes into account all o the current screen settings and calculates all possible combinations o Reerence, Feedback, and Post Divider values that will generate an output requency rom the input requency (3.5kHz multiplied by the desired multiple o 800. A box will appear: No solutions were ound! Do you want to retry calculations with the Check Loop Stability option turned o? Choose Yes. Another box will momentarily appear: Calculating Solutions: Press cancel to stop with the solutions calculated so ar. A number in the box will increment or every unique solution that is ound. This example will create eight unique solutions, which are then displayed in a window in the lower right portion o the program screen. For best results, try to keep the PostDiv value multiplied by the FbkDiv value rom getting larger than 5000 while running the VCO as much above 70MHz as possible. I a tradeo must be made, it is better to run the VCO aster and allow the divider values to get large. Solution #4 provides a PostDiv value o 800 and a FbkDiv value o 4 or a combined value o The VCO is running at about 00MHz. Click on Solution #4 to highlight the row, then click on Suggest in the Loop Filter box to have the program choose loop ilter values. Suggested values or an external loop ilter are 4700pF and 47kΩ. Now reselect the Check Loop Stability box to turn this eature on. Clicking on Calculate Solutions regenerates the same solutions provided earlier, only this time the new Loop Filter values were used. Figure 22: Line-Locked Screen Clicking on Solution #4 highlights the row, and clicking on Disp/Save Register Values provides a window with the inal values o key settings. A click on OK then displays a second window containing register inormation per the Register Map. I the solutions are to be saved to a ile, two ormats are available: a text ormat or viewing and a data ormat or loading into the FS63. Clicking on Load Solution into Hardware (i enabled sends the inormation in an I 2 C ormat to the FS63 via the parallel port. Note that this option is disabled or the Windows NT operating system. I your operating system can support parallel port communication but the connection cable is not attached, an error message is displayed: "The FS63 Hardware was not detected! "Make sure that it is connected to the LPT# printer port and that it is properly connected to a +5Volt power supply." Table 23: Cable Interace Color J DB25 Signal Red 2, 3 SCL White 2 3, 2 SDA Green 3 8 ADDR Blue Brown Black 6 25 GND 28