SGM706 Low-Cost, Microprocessor Supervisory Circuit

Size: px
Start display at page:

Download "SGM706 Low-Cost, Microprocessor Supervisory Circuit"

Transcription

1 GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power-supply and monitor microprocessor activity. It significantly improves system reliability and accuracy compared to separate ICs or discrete components. The provides power-supply monitoring circuitry that generates a reset output during power-up, power-down and brownout conditions. The reset output remains operational with as low as 1V. Independent watchdog monitoring circuitry is also provided. This is activated if the watchdog input has not been toggled within 1.6 seconds. In addition, there is a 1.25V threshold detector for power-fail warning, low-battery detection, or monitoring an additional power supply. An active-low manual-reset input (MR) is also included. The is available in Green SOIC-8 package. It operates over an ambient temperature range of -40 to +85. FEATURES Precision Supply-Voltage Monitor 4.65V for -L 4.40V for -M 4.0V for -J 3.08V for -T 2.93V for -S 2.63V for -R Guaranteed Valid at = 1V 200ms Reset Pulse Width Debounced TTL/CMOS-Compatible Manual-Reset Input Independent Watchdog Timer (1.6sec) Timeout Voltage Monitor for Power-Fail or Low-Battery Warning -40 to +85 Operating Temperature Range Green SOIC-8 Package APPLICATIONS Computers Controllers Intelligent Instruments Automotive Systems Critical μp Power Monitoring REV. A. 2

2 PACKAGE/ORDERING INFORMATION MODEL THRESHOLD (V) PACKAGE DESCRIPTION ORDERING NUMBER PACKAGE MARKING PACKAGE OPTION 4.65 SOIC-8 -LYS8G/TR -LYS8 Tape and Reel, SOIC-8 -MYS8G/TR -MYS8 Tape and Reel, SOIC-8 -JYS8G/TR -JYS8 Tape and Reel, SOIC-8 -TYS8G/TR -TYS8 Tape and Reel, SOIC-8 -SYS8G/TR -SYS8 Tape and Reel, SOIC-8 -RYS8G/TR -RYS8 Tape and Reel, 2500 NOTE: Order number is defined as the follow: ORDER NUMBER SGM 706- X Y X G / TR CAUTION Tape and Reel Green product Package Type S8 SOIC-8 Operating Temperature Range Y -40 to +85 THRESHOLD L: 4.65V M:4.40V J: 4.0V T: 3.08V S: 2.93V R: 2.63V This integrated circuit can be damaged by ESD if you don t pay attention to ESD protection. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS (Typical values are at T A = +25, unless otherwise noted.) Terminal Voltage (with respect to ) V to 6.0V All Other Inputs V to ( + 0.3V) Input Current,...20mA... 20mA Output Current, (all outputs)... 20mA Operating Temperature Range to +85 Junction Temperature Storage Temperature to +150 Lead Temperature (Soldering, 10sec) ESD Susceptibility HBM V MM...300V NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. SGMICRO reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. Please contact SGMICRO sales office to get the latest datasheet. 2

3 TYPICAL OPERATION CIRCUIT UNREGULATED DC +5V DC LINEAR REGULATOR MICROPROCESSOR PFI WDI WDO I/O LINE NMI PUSHBUTTON SWITCH MR INTERRUPT 3

4 PIN CONFIGURATION (TOP VIEW) MR 1 8 WDO WDI PFI 4 5 SOIC-8 PIN DESCRIPTION PIN NAME FUNCTION 1 MR Manual-Reset Input triggers a reset pulse when pulled below 0.8V. This active-low input has an internal 250μA ( = +5V) pull-up current. It can be driven from a TTL or CMOS logic line as well as shorted to ground with a switch. 2 Power Supply Voltage that is monitored. 3 0V Ground Reference for all signals. 4 PFI 5 6 WDI 7 8 WDO Power-Fail Voltage Monitor Input. When PFI is less than 1.25V, goes low. Connect PFI to or when not used. Power-Fail Output goes low and sinks current when PFI is less than 1.25V; otherwise stays high. Watchdog Input. If WDI remains high or low for 1.6sec, the internal watchdog timer runs out and WDO goes low (BLOCK DIAGRAM). Floating WDI or connecting WDI to a high-impedance three-state buffer disables the watchdog feature. The internal watchdog timer clears whenever reset is asserted, WDI is three-stated, or WDI sees a rising or falling edge. Active-Low Reset Output pulses low for 200ms when triggered, and stays low whenever is below the reset threshold (4.65V for -L, 4.4V for -M, 4.0V for -J, 3.08V for -T and 2.93V for -S, 2.63V for -R). It remains low for 200ms after rises above the reset threshold or MR goes from low to high. A watchdog timeout will not trigger unless WDO is connected to MR. Watchdog Output pulls low when the internal watchdog timer finishes its 1.6sec count and does not go high again until the watchdog is cleared. WDO also goes low during low-line conditions. Whenever is below the reset threshold, WDO stays low; however, unlike, WDO does not have a minimum pulse width. As soon as rises above the reset threshold, WDO goes high with no delay. 4

5 ELECTRICAL CHARACTERISTICS ( = 4.75V to 5.5V for -L; = 4.5V to 5.5V for -M; = 4.07V to 5.5V for -J; = 3.14V to 5.5V for -T; = 2.95V to 5.5V for -S; = 2.68V to 5.5V for -R; T A = -40 C to +85 C, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP MAX UNITS Operating Voltage Range () V Supply Current (I SUPPLY) μa Reset Threshold (V RT ) Reset Threshold Hysteresis -L M J T S R L, -M 40 -J 34 -T, -S 25 -R 22 Reset Pulse Width (t RS) ms Output Voltage I SOURCE = 800μA I sink = 3.2mA 0.4 = 1V, I sink = 50μA 0.3 Watchdog Timeout Period (t WD) sec WDI Pulse Width (t WP ) V IL = 0.4V, V IH = 70 ns WDI Input Threshold WDI Input Current WDO Output Voltage Low = 5V 0.8 High = 5V 3.5 Low V RST(MAX) < < 3.6V 0.8 High V RST(MAX) < < 3.6V 0.7 WDI = WDI = 0V I SOURCE = 800μA I sink = 1.2mA 0.4 MR Pull-Up Current MR = 0V μa MR Pulse Width (t MR ) 250 ns MR Input Threshold Low 0.8 T A = +25 High 2 MR to Reset Out Delay (t MD ) 350 ns PFI Input Threshold = 5V V PFI Input Current 0.2 na Output Voltage I SOURCE = 800μA I sink = 3.2mA 0.4 V mv V V μa V V V 5

6 BLOCK DIAGRAM WDI 6 WATCHDOG TRANSITION DETECTOR WATCHDOG TIMER 8 WDO MR 1 250µA TIMEBASE FOR AND WATCHDOG 2 + _ GENERATOR 7 PFI V for -L* + _ V * 4.65V for -L 4.40V for -M 4.0V for -J 3.08V for -T 2.93V for -S 2.63V for -R 3 6

7 TYPICAL PERFORMANCE CHARACTERISTICS 2kΩ 330pF 10kΩ 30pF PFI +5V pF +1.25V 1kΩ PFI + +5V 1kΩ V 30pF 7

8 TYPICAL PERFORMANCE CHARACTERISTICS 8

9 APPLICATION NOTES Ensuring a Valid Output Down to = 0V When falls below 1V, the output no longer sinks current it becomes an open circuit. High-impedance CMOS logic inputs can drift to undetermined voltages if left undriven. If a pull-down resistor is added to the pin as shown in Figure 1, any stray charge or leakage currents will be drained to ground, holding low. Resistor value (R1) is not critical. It should be about 100kΩ, large enough not to load and small enough to pull to ground. Figure 1. Valid to Ground Circuit Monitoring Voltages Other Than the Unregulated DC Input Monitor voltages other than the unregulated DC by connecting a voltage divider to PFI and adjusting the ratio appropriately. If required, add hysteresis by connecting a resistor (with a value approximately 10 times the sum of the two resistors in the potential divider network) between PFI and. A capacitor between PFI and will reduce the power-fail circuit s sensitivity to high-frequency noise on the line being monitored. can be asserted on other voltages in addition to the +5V line. Connect to MR to initiate a pulse when PFI drops below 1.25V. Figure 2 shows the configured to assert when the +5V supply falls below the reset threshold, or when the +12V supply falls below approximately 11V. +12V +5V R1 Monitoring a Negative Voltage The power-fail comparator can also monitor a negative supply rail (Figure 3). When the negative rail is good (a negative voltage of large magnitude), is low, and when the negative rail is degraded (a negative voltage of lesser magnitude), is high. By adding the resistors and transistor as shown, a high triggers reset. As long as remains high, the will keep reset asserted ( = low, = high). Note that this circuit s accuracy depends on the PFI threshold tolerance, the line, and the resistors. +5V R1 R2 V- +5V MR 0V +5V 0V PFI R1 MR 100kΩ V- V TRIP 0V = V TRIP R2 TO μp V TRIP < 0 100kΩ 2N3904 Figure 3. Monitoring a Negative Voltage Interfacing to μps with Bidirectional Reset Pins μps with bidirectional reset pins, such as the Motorola 68HC11 series, can contend with the output. If, for example, the output is driven high and the Microprocessor wants to pull it low, indeterminate logic levels may result. To correct this, connect a 4.7kΩ resistor between the output and the μp reset I/O, as in Figure 4. Buffer the output to other system components. BUFFRED TO OTHER SYSTEM COMPONENTS 1MΩ 1% 130kΩ 1% MR PFI TO µp VCC 4.7kΩ VCC Microprocessor Figure 2. Monitoring Both +5V and +12V Figure 4. Interfacing to Microprocessors with Bidirectional Reset I/O 9

10 PACKAGE OUTLINE DIMENSIONS SOIC-8 D e E1 E 5.2 b 1.27 RECOMMENDED LAND PATTERN (Unit: mm) L A A1 A2 θ c Dimensions In Millimeters Dimensions In Inches Symbol MIN MAX MIN MAX A A A b c D E E e 1.27 BSC BSC L θ

11 TAPE AND REEL INFORMATION REEL DIMENSIONS TAPE DIMENSIONS P2 P0 W Q1 Q2 Q1 Q2 Q1 Q2 B0 Q3 Q4 Q3 Q4 Q3 Q4 Reel Diameter P1 A0 K0 Reel Width (W1) DIRECTION OF FEED NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF TAPE AND REEL Package Type Reel Diameter Reel Width W1 A0 B0 K0 P0 P1 P2 W Pin1 Quadrant SOIC Q1 11

12 CARTON BOX DIMENSIONS NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF CARTON BOX Reel Type Length Width Height Pizza/Carton

SGM706 Low-Cost, Microprocessor Supervisory Circuit

SGM706 Low-Cost, Microprocessor Supervisory Circuit GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power-supply and monitor microprocessor activity. It significantly improves

More information

SGM706 Low-Cost, Microprocessor Supervisory Circuit

SGM706 Low-Cost, Microprocessor Supervisory Circuit GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power supply and monitor microprocessor activity. It significantly improves

More information

Low Cost P Supervisory Circuits ADM705 ADM708

Low Cost P Supervisory Circuits ADM705 ADM708 a FEATURES Guaranteed Valid with = 1 V 190 A Quiescent Current Precision Supply-Voltage Monitor 4.65 V (ADM707) 4.40 V (/) 200 ms Reset Pulsewidth Debounced TTL/CMOS Manual Reset Input () Independent Watchdog

More information

Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708

Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708 Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708 FEATURES Guaranteed valid with VCC = V 90 μa quiescent current Precision supply voltage monitor 4.65 V (ADM705/ADM707) 4.40 V (ADM706/ADM708)

More information

Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708

Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708 Low Cost Microprocessor Supervisory Circuits ADM705/ADM706/ADM707/ADM708 FEATURES Guaranteed valid with VCC = V 90 μa quiescent current Precision supply voltage monitor 4.65 V (ADM705/ADM707) 4.40 V (ADM706/ADM708)

More information

MAX705 MAX708/MAX813L Low-Cost, µp Supervisory Circuits

MAX705 MAX708/MAX813L Low-Cost, µp Supervisory Circuits MAX0 MAX0/MAXL General Description The MAX0-MAX0/MAXL microprocessor (µp) supervisory circuits reduce the complexity and number of components required to monitor power-supply and battery functions in µp

More information

3 V, Voltage Monitoring Microprocessor Supervisory Circuits

3 V, Voltage Monitoring Microprocessor Supervisory Circuits 3 V, Voltage Monitoring Microprocessor Supervisory Circuits ADM706P/ADM706R/ADM706S/ADM706T, ADM708R/ADM708S/ADM708T FEATURES Precision supply voltage monitor 2.63 V (ADM706P, ADM706R, ADM708R) 2.93 V

More information

SGM8705 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator

SGM8705 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator SGM87 Micro-Power, CMOS Input, RRIO, 1.4V, GENERAL DESCRIPTION The SGM87 is a dual low power comparator with a typical power supply current of 3nA (per channel). It has the best-in-class power supply current

More information

SGM8701 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator

SGM8701 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator SGM871 GENERAL DESCRIPTION The SGM871 is an ultra low power comparator with a typical power supply current of 3nA. It has the best-in-class power supply current versus propagation delay performance. The

More information

IMP705/6/7/8, 813L8. atchdog timer Brownout detection. ection supply y monitor POWER MANAGEMENT. Key Features. Applications.

IMP705/6/7/8, 813L8. atchdog timer Brownout detection. ection supply y monitor POWER MANAGEMENT. Key Features. Applications. POWER MANAGEMENT Low-P -Power µp P Supervisor Circuits WatcW atchdog timer Brownout detection ection Power P supply y monitor or The IMP0/0/0/0 and IMPL CMOS supervisor circuits monitor power-supply and

More information

Description. Applications

Description. Applications μp Supervisor Circuits Features Precision supply-voltage monitor - 4.63V (PT7A7511, 7521, 7531) - 4.38V (PT7A7512, 7522, 7532) - 3.08V (PT7A7513, 7523, 7533) - 2.93V (PT7A7514, 7524, 7534) - 2.63V (PT7A7515,

More information

Low-Cost Microprocessor Supervisory Circuits with Battery Backup

Low-Cost Microprocessor Supervisory Circuits with Battery Backup General Description The / microprocessor (μp) supervisory circuits reduce the complexity and number of components required for power-supply monitoring and battery control functions in μp systems. These

More information

STM706T/S/R, STM706P, STM708T/S/R

STM706T/S/R, STM706P, STM708T/S/R STM706T/S/R, STM706P, STM708T/S/R 3V Supervisor FEATURES SUMMARY PRECISION MONITOR STM706/708 T: 3.00V V 3.15V S: 2.88V V 3.00V R; STM706P: 2.59V V 2.70V AND OUTPUTS 200ms (TYP) t rec WATCHDOG TIMER -

More information

SGM3127 White LED Driver with Low Dropout Current Source

SGM3127 White LED Driver with Low Dropout Current Source GENERAL DESCRIPTION The SGM3127 low-dropout bias supply for white LEDs is a high-performance alternative to the simple ballast resistors used in conventional white LED designs. It is optimized for low

More information

Introduction. Features. Applications

Introduction. Features. Applications 70-70/70P-707-70-70T/S/R-L Features Precision supply-voltage monitor -.V (70L/70, L, 70L/707) -.V (70M/70, M, 70M/70) -.0V (70T, T, 70T) -.9V (70S, S, 70S) -.V (70R, R/70P, 70R) -.V (70Z, Z, 70Z) -.0V

More information

SGM8706 Micro-Power, RRIO, 1.8V, Push-Pull Output Comparator with Integrated Voltage Reference GENERAL DESCRIPTION FEATURES APPLICATIONS

SGM8706 Micro-Power, RRIO, 1.8V, Push-Pull Output Comparator with Integrated Voltage Reference GENERAL DESCRIPTION FEATURES APPLICATIONS Micro-Power, RRIO, 1.V, Push-Pull Output GENERAL DESCRIPTION The is a low power comparator with a typical power supply current of 2.2µA. It features an uncommitted on-chip voltage reference, comparator

More information

SGM9203 Triple, 6th-Order, Video Filter Driver for SD/PS/HD (1080i)/HD (1080p)

SGM9203 Triple, 6th-Order, Video Filter Driver for SD/PS/HD (1080i)/HD (1080p) SGM923 for SD/PS/HD (18i)/HD (18p) PRODUCT DESCRIPTION The SGM923 is a comprehensive filtering solution designed to give designers the flexibility to easily filter and drive various video signals, including

More information

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator 150ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power

More information

Low Power μp Supervisor Circuits

Low Power μp Supervisor Circuits Low Power μp Supervisor Circuits General Description The ASM705 / 706 / 707 / 708 and ASM813L are cost effective CMOS supervisor circuits that monitor powersupply and battery voltage level, and μp/μc operation.

More information

140ms (min) WDO Pulse Period PART. Maxim Integrated Products 1

140ms (min) WDO Pulse Period PART. Maxim Integrated Products 1 19-2804; Rev 2; 12/05 5-Pin Watchdog Timer Circuit General Description The is a low-power watchdog circuit in a tiny 5- pin SC70 package. This device improves system reliability by monitoring the system

More information

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator 45ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power consumption,

More information

SGM W Fully Differential Audio Power Amplifier with Selectable Shutdown

SGM W Fully Differential Audio Power Amplifier with Selectable Shutdown GENERAL DESCRIPTION The SGM4996 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile phones. It is capable

More information

SGM4064 Over-Voltage Protection IC and Li+ Charger Front-End Protection IC with LDO Mode

SGM4064 Over-Voltage Protection IC and Li+ Charger Front-End Protection IC with LDO Mode GENERAL DESCRIPTION The SGM4064 is a charger front-end integrated circuit designed to provide protection to Li-ion batteries from failures of the charging circuitry. The IC continuously monitors the input

More information

April 2015 Rev FEATURES

April 2015 Rev FEATURES April 2015 Rev. 3.0.0 GENERAL DESCRIPTION The SP706R/S/T and SP708R/S/T series is a family of microprocessor (µp) supervisory circuits that integrate myriad components involved in discrete solutions which

More information

+5V, Low-Power µp Supervisory Circuits with Adjustable Reset/Watchdog

+5V, Low-Power µp Supervisory Circuits with Adjustable Reset/Watchdog 19-1078; Rev 4; 9/10 +5V, Low-Power µp Supervisory Circuits General Description The * low-power microprocessor (µp) supervisory circuits provide maximum adjustability for reset and watchdog functions.

More information

PART* MAX812_EUS-T TOP VIEW

PART* MAX812_EUS-T TOP VIEW 19-11; Rev ; /98 -Pin µp oltage Monitors General Description The are low-power microprocessor (µp) supervisory circuits used to monitor power supplies in µp and digital systems. They provide excellent

More information

SGM8925/7 110kHz, 6.4μA, Rail-to-Rail Output CMOS Operational Amplifiers

SGM8925/7 110kHz, 6.4μA, Rail-to-Rail Output CMOS Operational Amplifiers PRODUCT DESCRIPTION The SGM8925 and SGM8927 are low power, low offset voltage and rail-to-rail output voltage feedback amplifiers. They have a wide output voltage swing, and take the minimum operating

More information

SGM9119 Triple, 5th-Order, Standard Definition Video Filter Driver

SGM9119 Triple, 5th-Order, Standard Definition Video Filter Driver PRODUCT DESCRIPTION The SGM9119 is a low voltage, triple video amplifier with integrated reconstruction filters and input clamps. Specially suited for standard definition video signals, this device is

More information

Power-Supply Monitor with Reset

Power-Supply Monitor with Reset 9-036; Rev. 2; 2/05 Power-Supply Monitor with Reset General Description The provides a system reset during power-up, power-down, and brownout conditions. When falls below the reset threshold, goes low

More information

G692/G693 4-Pin µp Voltage Monitors with Manual Reset Input

G692/G693 4-Pin µp Voltage Monitors with Manual Reset Input 4-Pin µp Voltage Monitors with Manual Reset Input Features Precision Monitoring of +3V, +3.3V, and +5V Power-Supply Voltages Fully Specified Over Temperature Available in Three Output Configurations Push-Pull

More information

SGM4684 Chip Scale Packaging, Low-Voltage 0.4Ω, Dual, SPDT Analog Switch

SGM4684 Chip Scale Packaging, Low-Voltage 0.4Ω, Dual, SPDT Analog Switch GENERAL DESCRIPTION The SGM4684 is a dual, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch designed to operate from a single 1.8V to 5.5V power supply.

More information

3.0V/3.3V Microprocessor Supervisory Circuits MAX690T/S/R, MAX704T/S/R, MAX802T/S/R, MAX804 MAX806T/S/R. Features

3.0V/3.3V Microprocessor Supervisory Circuits MAX690T/S/R, MAX704T/S/R, MAX802T/S/R, MAX804 MAX806T/S/R. Features , MAX804 General Description These microprocessor (µp) supervisory circuits reduce the complexity and number of components required for power-supply monitoring and battery-control functions in µp systems.

More information

SGM2553/SGM2553D Precision Adjustable Current Limited Power Distribution Switches

SGM2553/SGM2553D Precision Adjustable Current Limited Power Distribution Switches /D GENERAL DESCRIPTION The and D power distribution switches are intended for applications where precision current limiting is required or heavy capacitive loads and short circuits are encountered and

More information

ADM6823. Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23. Data Sheet FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS

ADM6823. Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23. Data Sheet FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS Data Sheet Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23 FEATURES Precision low voltage monitoring 9 reset threshold options: 1.58 V to 4.63 V (typical) 140 ms (minimum)

More information

Low-Power, Single/Dual-Voltage μp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay

Low-Power, Single/Dual-Voltage μp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay General Description The MAX6412 MAX6420 low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed to assert a reset signal whenever the supply voltage

More information

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch GENERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/ double-throw (SPDT) CMOS video analog switch (Mux/ DeMux) designed to operate from a single 2.7V to 5.5V power supply. This 2-channel

More information

SGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch

SGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch GENERAL DESCRIPTION The SGM7222 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. SGM7222 is designed for the switching of

More information

Microprocessor Supervisory Circuit ADM1232

Microprocessor Supervisory Circuit ADM1232 Microprocessor Supervisory Circuit FEATURES Pin-compatible with MAX1232 and Dallas DS1232 Adjustable precision voltage monitor with 4.5 V and 4.75 V options Adjustable strobe monitor with 150 ms, 600 ms,

More information

SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain

SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain SGM9111 8MHz Rail-to-Rail Composite GENERAL DESCRIPTION The SGM9111 is a single rail-to-rail -pole output reconstruction filter with a -3dB bandwidth of 8MHz and 3V/µs slew rate. Operating from single

More information

Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825

Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825 Data Sheet Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825 FEATURES FUNCTIONAL BLOCK DIAGRAM Precision 2.5 V to 5 V power supply monitor 7 reset threshold

More information

SGM2551A/SGM2551C Precision Adjustable Current Limited Power Distribution Switches

SGM2551A/SGM2551C Precision Adjustable Current Limited Power Distribution Switches / GENERAL DESCRIPTION The SGM2551A and power distribution switches are intended for applications where precision current limiting is required or heavy capacitive loads and short circuits are encountered

More information

SGM MHz, Low Voltage SPDT Analog Switch in 6-pin SC70

SGM MHz, Low Voltage SPDT Analog Switch in 6-pin SC70 GENERAL DESCRIPTION The SGM3167 is a single, bidirectional, single-pole/ double-throw (SPDT) CMOS analog switches designed to operate from a single 1.8V to 5.5V supply. It features high-bandwidth (600MHz)

More information

Setup Period. General Description

Setup Period. General Description General Description The MAX6443 MAX6452 low-current microprocessor reset circuits feature single or dual manual reset inputs with an extended setup period. Because of the extended setup period, short switch

More information

SGM Channel PWM Dimming Charge Pump White LED Driver

SGM Channel PWM Dimming Charge Pump White LED Driver GENERAL DESCRIPTION The SGM3145 is a high performance white LED driver. It integrates current sources and automatic mode selection charge pump. The part maintains the high efficiency by utilizing a 1 /1.5

More information

SGM MHz, Triple, 6dB Video Driver

SGM MHz, Triple, 6dB Video Driver PRODUCT DESCRIPTION The SGM9117 includes triple high-speed video buffers with G = +2 in one package. Every video buffer has -db full signal bandwidth in excess of 2MHz, along with slew rates in excess

More information

RESET output (push-pull)

RESET output (push-pull) Features Precision supply-voltage monitor - 4.6V (PT7M78xxL) - 4.8V (PT7M78xxM except PT7M780/09/0M) -.08V (PT7M78xxT) -.9V (PT7M78xxS) -.6V (PT7M78xxR) -.V (PT7M78xxZ) -.0V (PT7M78xxY) - 4.00V (PT7M78xxJ)

More information

SGM8554 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier

SGM8554 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier PRODUCT DESCRIPTION The SGM8554 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V

More information

SGM8584 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier

SGM8584 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier PRODUCT DESCRIPTION The SGM8584 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V

More information

SGM48754 Quad SPST CMOS Analog Switch

SGM48754 Quad SPST CMOS Analog Switch GENERAL DESCRIPTION The is a CMOS analog switch configured as quad SPST. This CMOS device can operate from 2.5V to 5.5V single supplies. Each switch can handle rail-to-rail analog signals. The off-leakage

More information

SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch

SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power

More information

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch GERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/doublethrow (SPDT) CMOS video analog switch (Mux/DeMux) designed to operate at a single +5V supply. This 2-channel multiplexer/demultiplexer

More information

SGM3736 PWM Dimming, 38V Step-Up LED Driver

SGM3736 PWM Dimming, 38V Step-Up LED Driver GENERAL DESCRIPTION The SGM3736 is a versatile constant current LED driver with a high efficiency step-up converter architecture. The low-side power MOSFET is integrated in the device, significantly shrinking

More information

SON3130 FEATURES PRODUCT DESCRIPTION PIN CONFIGURATION (TOP VIEW) APPLICATIONS

SON3130 FEATURES PRODUCT DESCRIPTION PIN CONFIGURATION (TOP VIEW) APPLICATIONS PRODUCT DESCRIPTION The SON313 is designed for heart rate output with SON133(heart rate sensor) offering low cost. It has a wide input common mode voltage range and output voltage swing, and takes the

More information

SGM3127 White LED Driver with Low Dropout Current Source

SGM3127 White LED Driver with Low Dropout Current Source GENERAL DESCRIPTION The SGM3127 low-dropout bias supply for white LEDs is a high-performance alternative to the simple ballast resistors used in conventional white LED designs. It is optimized for low

More information

SGM Ω, 300MHz, Low-Power Full-Speed USB (12Mbps) Switch

SGM Ω, 300MHz, Low-Power Full-Speed USB (12Mbps) Switch GENERAL ESCRIPTION The SGM2258 is a high-performance, dual, single-pole/ double-throw (SPT) CMOS analog switch designed for switching USB 1.1 signals. High bandwidth and low on-resistance make this switch

More information

TOP VIEW RESET INPUT (RESET) RESET 2. Maxim Integrated Products 1

TOP VIEW RESET INPUT (RESET) RESET 2. Maxim Integrated Products 1 19-11; Rev ; 1/5 -Pin µp oltage Monitors General Description The are low-power microprocessor (µp) supervisory circuits used to monitor power supplies in µp and digital systems. They provide excellent

More information

SGM Ω, Low Voltage Quad, SPDT Analog Switch

SGM Ω, Low Voltage Quad, SPDT Analog Switch GENERAL DESCRIPTION The SGM3699 is a quad, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch that is designed to operate from a single 1.8V to 4.35V power

More information

High-Accuracy μp Reset Circuit

High-Accuracy μp Reset Circuit General Description The MAX6394 low-power CMOS microprocessor (μp) supervisory circuit is designed to monitor power supplies in μp and digital systems. It offers excellent circuit reliability by providing

More information

UT01VS50L Voltage Supervisor Data Sheet January 9,

UT01VS50L Voltage Supervisor Data Sheet January 9, Standard Products UT01VS50L Voltage Supervisor Data Sheet January 9, 2017 www.aeroflex.com/voltsupv The most important thing we build is trust FEATURES 4.75V to 5.5V Operating voltage range Power supply

More information

SGM42507 DC Motor/Coil Driver

SGM42507 DC Motor/Coil Driver ADVANCED DATASHEET SGM4507 GENERAL DESCRIPTION SGM4507 is a bridge-tie driver designed for actuating motors and coils bi-directionally. It translates logic level input waves to power driving outputs to

More information

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch

SGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch GERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/ double-throw (SPDT) CMOS video analog switch (Mux/DeMux) designed to operate at a single +5V supply. This 2-channel multiplexer/demultiplexer

More information

SGM % Efficient Synchronous Step-Up Converter with 1.1A Switch

SGM % Efficient Synchronous Step-Up Converter with 1.1A Switch GERAL DESCRIPTION The SGM0 is a constant frequency, current mode, synchronous step-up switching regulator. It can be used for generating V at 00mA from a.v rail or a Li-Ion battery. High switching frequency

More information

MAX6711L/M/R/S/T/Z, MAX6712L/M/R/S/T/Z, MAX6713L/M/R/S/T/Z. 4-Pin SC70 Microprocessor Reset Circuits with Manual Reset Input

MAX6711L/M/R/S/T/Z, MAX6712L/M/R/S/T/Z, MAX6713L/M/R/S/T/Z. 4-Pin SC70 Microprocessor Reset Circuits with Manual Reset Input General Description The MAX6711/MAX6712/MAX6713 are microprocessor (µp) supervisory circuits used to monitor the power supplies in µp and digital systems. They provide excellent circuit reliability and

More information

4-Pin μp Voltage Monitors with Manual Reset Input MAX811/MAX812

4-Pin μp Voltage Monitors with Manual Reset Input MAX811/MAX812 General Description The MAX811/MAX81 are low-power microprocessor (µp) supervisory circuits used to monitor power supplies in µp and digital systems. They provide excellent circuit reliability and low

More information

SGM W Audio Power Amplifier

SGM W Audio Power Amplifier GENERAL DESCRIPTION The SGM489 is a.2w, fully integrated, audio power amplifier. It is designed to maximize audio performance in portable applications such as mobile phone. The portable application requires

More information

SGM V Step-Up LED Driver

SGM V Step-Up LED Driver GENERAL DESCRIPTION The SGM3725 is a versatile constant current LED driver with a high efficiency step-up converter architecture. Unique technology and high 1.35A current limit allow SGM3725 to drive up

More information

SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch

SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch GENERAL DESCRIPTION The SGM44599 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power

More information

SGM9119 Triple, 5th Order, Standard Definition Video Filter Driver

SGM9119 Triple, 5th Order, Standard Definition Video Filter Driver PRODUCT DESCRIPTION The SGM9119 is a low-voltage, triple video amplifier with integrated reconstruction filter and input clamps. Specially suited for standard definition video signals, this device is ideal

More information

SGM8631/2/3/4 470μA, 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8631/2/3/4 470μA, 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers PRODUCT DESCRIPTION The SGM863 (single), SGM863 (dual), SGM8633 (single with shutdown) and SGM8634 (quad) are low noise, low voltage, and low power operational amplifiers, that can be designed into a wide

More information

SGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier

SGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier PRODUCT DESCRIPTION The is a low cost, single rail-to-rail input and output voltage feedback amplifier. It has a wide input common mode voltage range and output voltage swing, and takes the minimum operating

More information

SGM4863 Dual 2.1W Audio Power Amplifier Plus Stereo Headphone Function

SGM4863 Dual 2.1W Audio Power Amplifier Plus Stereo Headphone Function Dual.W Audio Power Amplifier GENERAL DESCRIPTION The SGM4863 is a dual bridge-connected audio power amplifier which, when connected to a 5V supply, will deliver.w into a 4Ω load or.5w into a 3Ω load with

More information

SGM2576/SGM2576B Power Distribution Switches

SGM2576/SGM2576B Power Distribution Switches /B GENERAL DESCRIPTION The and B are integrated typically 100mΩ power switch for self-powered and bus-powered Universal Series Bus (USB) applications. The and B integrate programmable current limiting

More information

RT9807. Micro-Power Voltage Detector with Manual Reset. General Description. Features. Applications. Pin Configurations. Ordering Information RT9807-

RT9807. Micro-Power Voltage Detector with Manual Reset. General Description. Features. Applications. Pin Configurations. Ordering Information RT9807- Micro-Power Voltage Detector with Manual Reset General Description The is a micro-power voltage detector with deglitched manual reset input which supervises the power supply voltage level for microprocessors

More information

Features. Ordering Information VCC MIC8114 RESET

Features. Ordering Information VCC MIC8114 RESET MIC8114 Microprocessor Reset Circuit General Description The MIC8114 is an inexpensive microprocessor supervisory circuit that monitors the power supply in microprocessor based systems. The function of

More information

PT7M6314US. Supervisory Circuit General Description. Features. Pin Configuration. Description

PT7M6314US. Supervisory Circuit General Description. Features. Pin Configuration. Description Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:

More information

Low-Cost Microprocessor Supervisory Circuits with Battery Backup

Low-Cost Microprocessor Supervisory Circuits with Battery Backup 19-0130; Rev 2; 11/05 Low-Cost Microprocessor Supervisory General Description The microprocessor (µp) supervisory circuits reduce the complexity and number of components required for power-supply monitoring

More information

μp Supervisors Benefits and Features General Description Typical Operating Circuit Applications

μp Supervisors Benefits and Features General Description Typical Operating Circuit Applications Click here for production status of specific part numbers. MAX16000 MAX16007 General Description The MAX16000 MAX16007 are low-voltage, quad/hex/ octal-voltage μp supervisors in small TQFN and TSSOP packages.

More information

SGM mA Buck/Boost Charge Pump LED Driver

SGM mA Buck/Boost Charge Pump LED Driver GENERAL DESCRIPTION The SGM3140 is a current-regulated charge pump ideal for powering high brightness LEDs for camera flash applications. The charge pump can be set to regulate two current levels for Flash

More information

SGM8140 Low Power, Vibration Sensor and PIR Sensor Analog Front End (AFE)

SGM8140 Low Power, Vibration Sensor and PIR Sensor Analog Front End (AFE) SGM814 PRODUCT DESCRIPTION The SGM814 is a PIR sensor and vibration sensor analog front end which consists of 2 independent building block circuits. One is a dual rail-to-rail input and output operational

More information

Low-Power, Single/Dual-Voltage µp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay. Maxim Integrated Products 1

Low-Power, Single/Dual-Voltage µp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay. Maxim Integrated Products 1 19-2336; Rev 2; 12/05 Low-Power, Single/Dual-Voltage µp Reset Circuits General Description The low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed

More information

PT7M7803/ / μp Supervisor Circuits

PT7M7803/ / μp Supervisor Circuits Features Precision supply-voltage monitor -.6V (PT7M78xxL) -.8V (PT7M78xxM) -.08V (PT7M78xxT) -.9V (PT7M78xxS) -.6V (PT7M78xxR) -.V (PT7M78xxZ) -.0V (PT7M78xxY) -.00V (PT7M78xxJ) -.5V (PT7M78xxK) -.80V

More information

PT7M6315US. Pin Configuration PT7M6315USxxD3F/D4F. Pin Description

PT7M6315US. Pin Configuration PT7M6315USxxD3F/D4F. Pin Description Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5 in 100m increments Operating voltage range: 1.0 ~ 5.5 Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:

More information

SGM8621/2/3/4 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8621/2/3/4 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers SGM8621/2/3/4 3MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The SGM8621 (single), SGM8622 (dual), SGM8623 (single with shutdown) and SGM8624 (quad) are low noise, low voltage, and low power operational amplifiers,

More information

SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain

SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain PRODUCT DESCRIPTION The SGM9111 is single rail-to-rail 5-pole output reconstruction filter with a -3dB bandwidth of 8MHz and a slew rate of 3.8V/µs. Operating from single supplies ranging from 3.V to 5.5V

More information

SGM W Mono Fully Differential Audio Power Amplifier

SGM W Mono Fully Differential Audio Power Amplifier .3W Mono Fully Differential GENERAL DESCRIPTION The SGM4995 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile

More information

SGM9119 Triple, 5th Order, Standard Definition Video Filter Driver

SGM9119 Triple, 5th Order, Standard Definition Video Filter Driver PRODUCT DESCRIPTION The SGM9119 is a low-voltage, triple video amplifier with integrated reconstruction filter and input clamps. Specially suited for standard definition video signals, this device is ideal

More information

PT7M1818/1813 Supervisory Circuit

PT7M1818/1813 Supervisory Circuit Features Highly accurate: 1.5% (25 C) Accurate power monitoring: 2.5V, 2.9V, 3. (PT7M1818), and 4.1, 4.3, 4.6V (PT7M1813) Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C

More information

SGM % Efficient Synchronous Step-Up Converter with 1.1A Switch

SGM % Efficient Synchronous Step-Up Converter with 1.1A Switch GERAL DESCRIPTION The SGM0 is a constant frequency, current mode, synchronous step-up switching regulator. Its output currents can go as high as 7mA while using a single-cell alkaline, and discharge it

More information

Dual Processor Supervisors with Watchdog ADM13305

Dual Processor Supervisors with Watchdog ADM13305 Dual Processor Supervisors with Watchdog ADM335 FEATURES Dual supervisory circuits Supply voltage range of 2.7 V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V voltage

More information

SGM6232 2A, 38V, 1.4MHz Step-Down Converter

SGM6232 2A, 38V, 1.4MHz Step-Down Converter GENERAL DESCRIPTION The is a current-mode step-down regulator with an internal power MOSFET. This device achieves 2A continuous output current over a wide input supply range from 4.5V to 38V with excellent

More information

AME. n General Description. n Applications. n Typical Application. n Function Diagram. n Features

AME. n General Description. n Applications. n Typical Application. n Function Diagram. n Features n General Description The AME8510/8520/8530 family allows the user to customize the CPU monitoring function without any external components. The user has a large choice of reset voltage thresholds and

More information

SGM % Efficient Synchronous Step-Up Converter with 1A Switch

SGM % Efficient Synchronous Step-Up Converter with 1A Switch Preliminary Datasheet SGM0 GERAL DESCRIPTION The SGM0 is a constant frequency, current mode, synchronous, step-up switching regulator. Its output currents can go as high as 7mA while using a single-cell

More information

Ultra-Low-Voltage µp Reset Circuits and Voltage Detectors

Ultra-Low-Voltage µp Reset Circuits and Voltage Detectors 19-2625; Rev 2; 12/05 Ultra-Low-oltage µp Reset Circuits and General Description The microprocessor (µp) supervisory circuits monitor ultra-low-voltage power supplies in µp and digital systems. They provide

More information

TOP VIEW WDS1 WDS2. Maxim Integrated Products 1

TOP VIEW WDS1 WDS2. Maxim Integrated Products 1 9-3896; Rev ; /06 System Monitoring Oscillator with General Description The replace ceramic resonators, crystals, and supervisory functions for microcontrollers in 3.3V and 5V applications. The provide

More information

SGM6132 3A, 28.5V, 1.4MHz Step-Down Converter

SGM6132 3A, 28.5V, 1.4MHz Step-Down Converter GENERAL DESCRIPTION The SGM6132 is a current-mode step-down regulator with an internal power MOSFET. This device achieves 3A continuous output current over a wide input supply range from 4.5V to 28.5V

More information

SGM321/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM321/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers /SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers GENERAL DESCRIPTION The (single), SGM358 (dual) and SGM324 (quad) are low cost, rail-to-rail input and output voltage feedback amplifiers.

More information

CE OUT ADDRESS DECODER CE IN OVO LOW LINE RESET RESET 8 9 SWT. Maxim Integrated Products 1

CE OUT ADDRESS DECODER CE IN OVO LOW LINE RESET RESET 8 9 SWT. Maxim Integrated Products 1 9-047; Rev. 4; /05 Microprocessor and Nonvolatile General Description The microprocessor (µp) supervisory circuits provide the most functions for power-supply and watchdog monitoring in systems without

More information

ASM1232LP/LPS 5V μp Power Supply Monitor and Reset Circuit

ASM1232LP/LPS 5V μp Power Supply Monitor and Reset Circuit 5V μp Power Supply Monitor and Reset Circuit General Description The ASM1232LP/LPS is a fully integrated microprocessor Supervisor. It can halt and restart a hung-up microprocessor, restart a microprocessor

More information

SGM8631/2/3 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8631/2/3 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers /2/3 6MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The (single), SGM8632 (dual) and SGM8633 (single with shutdown) are low noise, low voltage, and low power operational amplifiers that can be designed into

More information

SGM mW Differential Input, Stereo Audio Power Amplifier

SGM mW Differential Input, Stereo Audio Power Amplifier SGM482 2mW Differential Input, GENERAL DESCRIPTION The SGM482 is a stereo audio power amplifier with differential inputs. Operating on a single 5V power supply, it delivers 2mW of continuous RMS power

More information