Servo and Motor Controller

Size: px
Start display at page:

Download "Servo and Motor Controller"

Transcription

1 Servo and Motor Controller Date: August 0, 00 Description: The servo motor controller drives three R/C servomotors and one brushless DC motor. All four motors are controlled by PWM signals sent from a PIC F microcontroller. The PWM signal to the brushless motor is used to toggle on/off an Allegro A9 three-phase PWM motor driver. The servo controller regulates the shaft velocity of the brushless motor with encoder feedback, which is decoded by an HCTL000 quadrature decoder. An in-circuit serial programming connector is provided on the PCB to allow for in board reprogramming of the PIC micro-controller. PCB Block Diagram: R/C Servo R/C Servo R/C Servo Serial Comms Microcontroller (PICF) PWM motor Driver (A9) -Phase Brushless Motor V Logic Supply Hall Sensors V Motor Supply Quadrature Decoder (HCTL000) Encoder Feedback Power Consumption: Logic Supply: V (max current:. A) Motor Supply: V (operates between V 0V, max current: A) Data Interface: TTL-level -wire serial

2 Control System: The DC motor sends out encoded position signals to the quadrature decoder chip. The microcontroller reads the position feedback information from the decoder and converts it into a velocity reading. This velocity data is then compared to the desired speed and an error signal is generated, which is used to calculate the PD compensation. Desired Speed - Controller (PICF) Plant (Motor) Shaft Velocity Encoder Circuit Schematics: J J J Serv omotor Serv omotor Serv omotor C00 C0 pf C pf ENABLE Y CRYSTAL/SM 9 0 U Vpp RB RA0/AN0 RB RA/AN RB RA/AN/VREF- RB RA/AN/VREF+ RB RA/T0CK RB RA/AN/SS/LVDIN RB/INT VSS RB0/INT0 OSC/CLK 0 9 OSC/CLO0/RA VSS RC0/TOSO/TCLKL RC/RX/DT RC/TOSI/CCP RC/TX/CK RC/CCP RC/SDO RC/SCK/SCL RC/SDI/SDA PICF 9 J 0 HEADER x/m signal_groud C0.uF.uF J RX TX GND RS(TTL) DIR C00 U Output enable Vcc GND Output MX0 Oscillator C00.uF U CHA D0 CHB D D CLK D D OE D 0 RST D 9 SEL D GND HCTL000.uF Schematic : Logic Section C C C C 0.mF J v GND A B Z C C C Motor Signals

3 signal_groud Hall Sensors C C C R K R K + C mf R9 0K R 0K R 0K GND GND HA+ HA- HB+ HB- HC+ HC- REF GND GND GND BRAKE SENSE SR OUTA HBIAS VBB LSS OUTB GNDa GND PFD PFD BLANK EXTMODE 0 ENABLE 9 DIR Vreg OSC GND0 GND9 GND SLEEP CP 0 CP 9 Vcp OUTC TACH VBB LSS GND GND R K ENABLE DIR C0 0.mF C 0.mF VBB C9 0.mF/00V + C mf R C 0.Ohm 0.mF/00V VBB D0 D D DIODE SCHOTTKY J VBB J J DIODE SCHOTTKY D D D9 MOTOR Motor Power Logic Power Schematic : Power Section

4 PCB Drawings Figure : PCB Layout Top

5 Figure : PCB Layout Bottom

6 Bill of Materials: # per Name Value Footprint Notes Vendor Part # Board C uf, 00V Cylinder Electrolytic Digi-Key P9-ND C, C9, C, C0, C 0.uF, 0V SM/C_0 Ceramic XR Digi-Key 99---ND C uf, 00V Cylinder Electrolytic Digi-Key P9-ND C0, C pf, 0V SM/C_0 Ceramic Digi-Key PCC0CQCT-ND C00, C0, C00, C00 0.uF, 0V SM/C_0 Ceramic XR Digi-Key ND D, D, D9, D0, D, D Diode, 00V, A SM/D Fast Recovery Digi-Key FRBDICT-ND J Connector x mm ICSP connector Digi-Key J, J, J, J, J Connector x mm J Connector x mm J, J Connector x mm V motor power Digi-Key Brushless motor -phase power Digi-Key H0-ND (Recepticle) H0-ND (Header) Brushless motor logic and encoder feedback Digi-Key H-ND (Header) H0-ND (Recepticle) H0-ND (Header) IC socket pin Holds half HCTL00 Digi-Key AE90-ND R, R K SM/R 0 % /W Digi-Key P.00KLCT-ND R, R, R9 0K SM/R 0 % /W Digi-Key -0.0KLCT-ND R 0.Ohm Radial Current-Sense Res Digi-Key FR0-ND R K SM/R 0 % /W Digi-Key -.0KLCT-ND U HCTL000 Through hole Quadrature Decoder U 0MHz OSC SMD HSM9H Digi-Key CW0-ND U PIC F SOIC pin Microcontroller Digi-Key PICF-I/SO-ND Y 0MHz Crystal SMT Can ATS00SM Digi-Key CTX0-ND V, 0W, Shinano Kenshi Brushless Motor Encoder LA0-00E-NL Resettable fuse.a V SMD MF-SMCT-ND

7 Overview of Code: The program for the PIC is broken up into the three sections: Main program, Low Priority Interrupt Service Routine, High Priority Interrupt Service Routine INITIALIZATION Configuration Bits: Oscillator set to HS (0MHz) Disable all other bit word settings Configuration Variables: Motor speed Max = -00rpm to 00rpm Motor PWM period = FF ( clock cycles) Max motor duty cycle = 000 Fin position = 000 to 000 (000 is initialized position) Baud Rate =.k Internal clock = 0MHz MAIN PROGRAM While loop overview: Processing Command: No Command is sent: Wait for new command to be sent Poll motor speed and correct if necessary Send out PWM signals to three fins Returns motor speed and PWM signals Once command is received from DimmPC it is searched for each element Format of command: axxxxbxxxxcxxxxmxxxx (All or portions of the command may be sent) Each element is saved into a variable to be implemented in the ISR s If x is sent new speeds are not returned If e is sent speeds are returned Until a new command is received the speed is continuously polled and updated After each speed check, the speed and PWM signal is returned to the user. HIGH PRIORITY INTERRUPT Triggered by Fins Flag: step cycle: Set fin a high, Set fin a low Set fin b high, Set fin b low Set fin c high, Set fin c low One step is implement each ISR is called due to Triggered by command: When a command is received, the receive buffer triggers this ISR The ISR then saves and receives the data into a command buffer The received command flag is set so the main while loop will process the command when ISR exits LOW PRIORITY INTERRUPT Triggered by Motor Flag: Reads the decoder chip and exits ISR (repeats 0 times) Read decoder 0 times (multiple reads decreases error) Convert data to rpm (freq of 0 th read = 0.Hz) Compare with goal speed to get speed error Calculate speed comp based on error Update duty cycle and direction Triggered by Communication Error: If no command has been received in the past two seconds, the motor speed is set to zero and the fins are set to 000 (center). This is a fail safe to stop the AUV in the event that there is a communication problem between the DimmPC and the motor control card.

8 PCB Pictures

9

JX pin PIC Microcontroller Project Board

JX pin PIC Microcontroller Project Board JX-877 40-pin PIC Microcontroller Project Board Specification Connect to PC s parallel port for programming with CX-6 cable (included) PIC16F877-20/P on-board, support all 40-pin of PIC16F and 18F series.

More information

Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller

Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller Microcontroller Based Controls 2 DC Motors 0-5V Analog, 1-2mS pulse or Serial Inputs for Motor Speed 10KHz, 1.25KHz or 156Hz selectable

More information

SCHEMATIC X4.1 X4.2 SPD VDD J6 PWM_OC PWM LED1 GND VSS PWM GND. PWM_Loc. GND 10u BS170G. STRn TP7 TP6 TP8 TP5 SCK SDI SDO SPD. STRn GND GND SPD.

SCHEMATIC X4.1 X4.2 SPD VDD J6 PWM_OC PWM LED1 GND VSS PWM GND. PWM_Loc. GND 10u BS170G. STRn TP7 TP6 TP8 TP5 SCK SDI SDO SPD. STRn GND GND SPD. 1 1 1 8 7 7 8 A9 SCHEMATIC Allegro Microsystems Inc Worcester MA 010 USA DATE: PCB: 17th Jul 01 EDC AUTHOR: Yi Li SHEET: 1 of 1 REV: SIZE: A. TITLE: D A9 Demonstration Board Rev D X.1 X. X. X. X. X. FTDI

More information

CMU232 User Manual Last Revised October 21, 2002

CMU232 User Manual Last Revised October 21, 2002 CMU232 User Manual Last Revised October 21, 2002 Overview CMU232 is a new low-cost, low-power serial smart switch for serial data communications. It is intended for use by hobbyists to control multiple

More information

PIC Functionality. General I/O Dedicated Interrupt Change State Interrupt Input Capture Output Compare PWM ADC RS232

PIC Functionality. General I/O Dedicated Interrupt Change State Interrupt Input Capture Output Compare PWM ADC RS232 PIC Functionality General I/O Dedicated Interrupt Change State Interrupt Input Capture Output Compare PWM ADC RS232 General I/O Logic Output light LEDs Trigger solenoids Transfer data Logic Input Monitor

More information

IRAC1150-D2 Control Board User s Guide

IRAC1150-D2 Control Board User s Guide Computing & Communications SBU - AC-DC Applications Group 222 Kansas Street, El Segundo CA90245, California, USA IRAC1150-D2 Control Board User s Guide Rev. 2.0 7/6/2005 Rev. 2.0 7/6/2005 International

More information

Universal Square Wave Generator Stable all the way up to RF

Universal Square Wave Generator Stable all the way up to RF Elektor Post Project No. Universal Square Wave Generator Stable all the way up to RF A square wave generator is useful in a test environment, and often the harmonic content of a simple square wave signal

More information

' The PicBasic Pro Compiler Manual is on line at: '

' The PicBasic Pro Compiler Manual is on line at: ' ---------------Title-------------- File...4331_encoder4.pbp Started...1/10/10 Microcontroller Used: Microchip Technology 18F4331 Available at: http://www.microchipdirect.com/productdetails.aspx?category=pic18f4331

More information

A3949. DMOS Full-Bridge Motor Driver. Features and Benefits Single supply operation Very small outline package Low R DS(ON)

A3949. DMOS Full-Bridge Motor Driver. Features and Benefits Single supply operation Very small outline package Low R DS(ON) Features and Benefits Single supply operation Very small outline package Low R DS(ON) outputs Sleep function Internal UVLO Crossover current protection Thermal shutdown protection Packages: Description

More information

A3959. DMOS Full-Bridge PWM Motor Driver

A3959. DMOS Full-Bridge PWM Motor Driver Features and Benefits ±3 A, 50 V Output Rating Low r DS(on) Outputs (70 m, Typical) Mixed, Fast, and Slow Current-Decay Modes Synchronous Rectification for Low Power Dissipation Internal UVLO and Thermal-Shutdown

More information

SR A, 30V, 420KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION

SR A, 30V, 420KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION SR2026 5A, 30V, 420KHz Step-Down Converter DESCRIPTION The SR2026 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 5A continuous output current over a

More information

User s Manual ISL71218MEVAL1Z. User s Manual: Evaluation Board. High Reliability Space

User s Manual ISL71218MEVAL1Z. User s Manual: Evaluation Board. High Reliability Space User s Manual ISL71218MEVAL1Z User s Manual: Evaluation Board High Reliability Space Rev. Aug 217 USER S MANUAL ISL71218MEVAL1Z Evaluation Board UG139 Rev.. 1. Overview The ISL71218MEVAL1Z evaluation platform

More information

Frequency Synthesizer Project ECE145B Winter 2011

Frequency Synthesizer Project ECE145B Winter 2011 Frequency Synthesizer Project ECE145B Winter 2011 The goal of this last project is to develop a frequency synthesized local oscillator using your VCO from Lab 2. The VCO will be locked to a stable crystal

More information

SPY ROBOTIC MODULE USING ZIGBEE

SPY ROBOTIC MODULE USING ZIGBEE SPY ROBOTIC MODULE USING ZIGBEE Prabhakaran.J,Mohammed Arif.K, Monish Kumar.R, Pavithra.D.N 4, Subha. K Assistant Professor,,,4, Student Members Department of Electronics and Communication Engineering

More information

Logosol AC/DC Intelligent Servo Drive for Coordinated Control LS-174WP

Logosol AC/DC Intelligent Servo Drive for Coordinated Control LS-174WP Features Motors supported: - Panasonic A and S series - Brushless 60/120 commutated - Brush-commutated (DC) motors Up to 20A peak, 12A continuous output current 12 to 90VDC power supply Separate motor

More information

L E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G

L E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G P R O F. S L A C K L E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G G B S E E E @ R I T. E D U B L D I N G 9, O F F I C E 0 9-3 1 8 9 ( 5 8 5 ) 4 7 5-5 1 0

More information

PRODUCT DESCRIPTION A NEW SERIAL-CONTROLLED MOTOR-DRIVER IC. by Thomas Truax and Robert Stoddard

PRODUCT DESCRIPTION A NEW SERIAL-CONTROLLED MOTOR-DRIVER IC. by Thomas Truax and Robert Stoddard PRODUCT DESCRIPTION Technical Paper STP 99-12 A NEW SERIAL-CONTROLLED by Thomas Truax and Robert Stoddard ABSTRACT A new serial-controlled IC has been specifically developed to drive dc motors. This paper

More information

Brushless DC Motor Controller

Brushless DC Motor Controller Brushless DC Motor Controller application INFO available FEATURES Drives Power MOSFETs or Power Darlingtons Directly 50V Open Collector High-Side Drivers Latched Soft Start High-speed Current-Sense Amplifier

More information

Digital Servo Motor Driver

Digital Servo Motor Driver SRVODRV-806 Description This digital servo drive is designed to drive brushed and brushless servomotors from a compact form factor ideal for embedded applications. This fully digital drive operates in

More information

HM V 2A 500KHz Synchronous Step-Down Regulator

HM V 2A 500KHz Synchronous Step-Down Regulator Features HM8114 Wide 4V to 30V Operating Input Range 2A Continuous Output Current Fixed 500KHz Switching Frequency No Schottky Diode Required Short Protection with Hiccup-Mode Built-in Over Current Limit

More information

Laboratory Exercise 1 Microcontroller Board with Driver Board

Laboratory Exercise 1 Microcontroller Board with Driver Board Laboratory Exercise 1 Microcontroller Board with Driver Board The purpose of this lab exercises is to demonstrate how the Microcontroller Board can be used to control motors connected to the Driver Board

More information

A3984. DMOS Microstepping Driver with Translator

A3984. DMOS Microstepping Driver with Translator Features and Benefits Low RDS(ON) outputs Automatic current decay mode detection/selection and current decay modes Synchronous rectification for low power dissipation Internal UVLO and thermal shutdown

More information

SCHEMATIC CN1 HC- HC+ HB- HB+ HA- HA+ PHA PHA VREF. Shunt VREF. 0.22uF VREF 8 HC- PHA HA- HC+ HB+ A SLUG OUTB GND. 10uF VBB PWM SEL FG JP2

SCHEMATIC CN1 HC- HC+ HB- HB+ HA- HA+ PHA PHA VREF. Shunt VREF. 0.22uF VREF 8 HC- PHA HA- HC+ HB+ A SLUG OUTB GND. 10uF VBB PWM SEL FG JP2 SCHEMATIC W W Allegro Logo Date: //0 Sheet of File: C:\altium\..\LPRev.SchDoc Drawn By: Bob Pickett A Size Number Revision 8-087-000-SCH Title D LP D Shunt SEL B SEL B PWMPin R k HA+ HA+ PWM/VSP PWM HA-

More information

RX23T inverter ref. kit

RX23T inverter ref. kit RX23T inverter ref. kit Deep Dive October 2015 YROTATE-IT-RX23T kit content Page 2 YROTATE-IT-RX23T kit: 3-ph. Brushless Motor Specs Page 3 Motors & driving methods supported Brushless DC Permanent Magnet

More information

Controlling DC Brush Motor using MD10B or MD30B. Version 1.2. Aug Cytron Technologies Sdn. Bhd.

Controlling DC Brush Motor using MD10B or MD30B. Version 1.2. Aug Cytron Technologies Sdn. Bhd. PR10 Controlling DC Brush Motor using MD10B or MD30B Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended

More information

Motor Control Development Kit

Motor Control Development Kit User s Manual, V 1.0, June 2003 Motor Control Development Kit A reference design for low voltage 3-phase AC induction and brushless DC motor control. Microcontrollers Never stop thinking. Revision History:2003-06

More information

LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER

LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER LSI/CSI LS7560N LS7561N LSI Computer Systems, Inc. 15 Walt Whitman Road, Melville, NY 747 (631) 71-0400 FAX (631) 71-0405 UL A3800 BRUSHLESS DC MOTOR CONTROLLER April 01 FEATURES Open loop motor control

More information

Servo click. PID: MIKROE 3133 Weight: 32 g

Servo click. PID: MIKROE 3133 Weight: 32 g Servo click PID: MIKROE 3133 Weight: 32 g Servo click is a 16-channel PWM servo driver with the voltage sensing circuitry. It can be used to simultaneously control 16 servo motors, each with its own programmable

More information

MAINTENANCE MANUAL AUDIO AMPLIFIER BOARD 19D904025G1 (MDR) AUDIO AMPLIFIER BOARD 19D904025G2 (MDX)

MAINTENANCE MANUAL AUDIO AMPLIFIER BOARD 19D904025G1 (MDR) AUDIO AMPLIFIER BOARD 19D904025G2 (MDX) A MAINTENANCE MANUAL AUDIO AMPLIFIER BOARD 19D904025G1 (MDR) AUDIO AMPLIFIER BOARD 19D904025G2 (MDX) TABLE OF CONTENTS DESCRIPTION............................................... Page Front Cover CIRCUIT

More information

EE 308 Spring S12 SUBSYSTEMS: PULSE WIDTH MODULATION, A/D CONVERTER, AND SYNCHRONOUS SERIAN INTERFACE

EE 308 Spring S12 SUBSYSTEMS: PULSE WIDTH MODULATION, A/D CONVERTER, AND SYNCHRONOUS SERIAN INTERFACE 9S12 SUBSYSTEMS: PULSE WIDTH MODULATION, A/D CONVERTER, AND SYNCHRONOUS SERIAN INTERFACE In this sequence of three labs you will learn to use the 9S12 S hardware sybsystem. WEEK 1 PULSE WIDTH MODULATION

More information

Pin-out Diagram VBB1 HOME SLEEP DIR ENABLE OUT1A OUT1B PFD RC1 AGND REF RC2 VDD OUT2A MS2 MS1 CP2 CP1 VCP PGND VREG STEP OUT2B RESET SR SENSE2

Pin-out Diagram VBB1 HOME SLEEP DIR ENABLE OUT1A OUT1B PFD RC1 AGND REF RC2 VDD OUT2A MS2 MS1 CP2 CP1 VCP PGND VREG STEP OUT2B RESET SR SENSE2 Microstepping DMOS Driver with Translator Features and Benefits ±2.5 A, 35 V output rating Low R DS(On) outputs: 0.28 Ω source, 0.22 Ω sink, typical Automatic current decay mode detection/selection 3.0

More information

7I30 MANUAL Quad 100W HBridge

7I30 MANUAL Quad 100W HBridge 7I30 MANUAL Quad 100W HBridge V1.3 This page intentionally almost blank Table of Contents GENERAL.......................................................... 1 DESCRIPTION.................................................

More information

A Phase Sinusoidal Motor Controller. Description

A Phase Sinusoidal Motor Controller. Description Features and Benefits Sinusoidal Drive Current Hall Element Inputs PWM Current Limiting Dead-time Protection FGO (Tach) Output Internal UVLO Thermal Shutdown Circuitry Packages: 32-Pin QFN (suffix ET)

More information

UHF RFID Micro Reader Reference Design Hardware Description

UHF RFID Micro Reader Reference Design Hardware Description Application Micro Note Reader Reference Design AS399x UHF RFID Reader ICs UHF RFID Micro Reader Reference Design Hardware Description Top View RF Part Bottom View RF Part www.austriamicrosystems.com/rfid

More information

HM V 3A 500KHz Synchronous Step-Down Regulator

HM V 3A 500KHz Synchronous Step-Down Regulator Features Wide 4V to 18V Operating Input Range 3A Continuous Output Current 500KHz Switching Frequency Short Protection with Hiccup-Mode Built-in Over Current Limit Built-in Over Voltage Protection Internal

More information

Design and Construction of PIC-based IR Remote Control Moving Robot

Design and Construction of PIC-based IR Remote Control Moving Robot Design and Construction of PIC-based IR Remote Control Moving Robot Sanda Win, Tin Shein, Khin Maung Latt Abstract This document describes an electronic speed control designed to drive two DC motors from

More information

SCHEMATIC TACHO_O DIAG_O PWM_I X1.6 X1.5 X1.8 X1.7 GND R28 R27 R25 R26 DIAG LED1 TP:DIAG R18. 47k. 6k8 R19 R17. 6k8 OFF TP:PWM R23.

SCHEMATIC TACHO_O DIAG_O PWM_I X1.6 X1.5 X1.8 X1.7 GND R28 R27 R25 R26 DIAG LED1 TP:DIAG R18. 47k. 6k8 R19 R17. 6k8 OFF TP:PWM R23. 1 1 2 2 3 4 2 6 7 5 9 8 3 3 4 4 5 5 6 6 A4960 SCHEMATIC REF X5.4 R21 X5.3 50k 1 2 3 +5 X5.2 STRN_I X5.1 D TITLE: A4960 Customer Demonstration Board D (Ground Bars) USB REV: SIZE: Allegro Microsystems Inc

More information

Assembly Manual for VFO Board 2 August 2018

Assembly Manual for VFO Board 2 August 2018 Assembly Manual for VFO Board 2 August 2018 Parts list (Preliminary) Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 10 104 capacitors 1 Rotary encode with switch 1 5-volt

More information

MicroToys Guide: Motors N. Pinckney April 2005

MicroToys Guide: Motors N. Pinckney April 2005 Introduction Three types of motors are applicable to small projects: DC brushed motors, stepper motors, and servo motors. DC brushed motors simply rotate in a direction dependent on the flow of current.

More information

A5977. Microstepping DMOS Driver with Translator

A5977. Microstepping DMOS Driver with Translator FEATURES AND BENEFITS ±2.8 A, 40 V output rating Low R DS(on) outputs, 0.22 Ω source, 0.15 Ω sink typical Automatic current decay mode detection/selection 3 to 5.5 V logic supply voltage range Mixed, fast,

More information

DASL 120 Introduction to Microcontrollers

DASL 120 Introduction to Microcontrollers DASL 120 Introduction to Microcontrollers Lecture 2 Introduction to 8-bit Microcontrollers Introduction to 8-bit Microcontrollers Introduction to 8-bit Microcontrollers Introduction to Atmel Atmega328

More information

A3987. DMOS Microstepping Driver with Translator

A3987. DMOS Microstepping Driver with Translator Features and Benefits Low R DS(on) outputs Short-to-ground protection Shorted load protection Automatic current decay mode detection/selection and slow current decay modes Synchronous rectification for

More information

Evaluates: MAX MAX20735 Evaluation Kit. General Description. Getting Started. Features. Required Equipment. Procedure

Evaluates: MAX MAX20735 Evaluation Kit. General Description. Getting Started. Features. Required Equipment. Procedure MAX07 Evaluation Kit Evaluates: MAX07 General Description The MAX07 Evaluation Kit (EV kit) serves as a reference platform for evaluating the MAX07 voltage regulator IC. This single-chip, integrated switching

More information

M/V Series Servo Drive AB250A060

M/V Series Servo Drive AB250A060 Description Power Range AB250A060 servo amplifiers are designed to drive brushless DC motors at a high switching frequency. It is fully protected against over-voltage, over-current, over-heating, under-voltage

More information

A3982. DMOS Stepper Motor Driver with Translator

A3982. DMOS Stepper Motor Driver with Translator OUT2A SENSE2 VBB2 OUT2B ENABLE PGND PGND CP1 CP2 VCP VREG MS1 1 2 3 4 5 6 7 8 9 10 11 12 Charge Pump Reg Package LB Translator & Control Logic AB SO LUTE MAX I MUM RAT INGS Load Supply Voltage,V BB...35

More information

Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package

Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package PD- 95805 Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package OMC506 Description: The OMC506 is an integrated, high density, three phase Brushless DC (BLDC) motor, speed controller

More information

Designing and Fabricating Fuzzy Controller of DC Servo Motor with HMI

Designing and Fabricating Fuzzy Controller of DC Servo Motor with HMI Designing and Fabricating Fuzzy Controller of DC Servo Motor with HMI Vo Quang Truong Department of Mechanical Engineering, Danang College of Technology, The University of Danang, Vietnam Abstract In this

More information

DISCONTINUED PRODUCT FOR REFERENCE ONLY.

DISCONTINUED PRODUCT FOR REFERENCE ONLY. LOAD SUPPLY CD2 C WD C ST OUTA GROUND GROUND OUT B OUT C CENTERTAP BRAKE CRES 1 2 3 4 5 6 7 8 9 10 11 12 MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING V BB COMMUTATION DELAY BOOST CHARGE PUMP Dwg. PP-040B

More information

Supertex inc. MD1822DB3. MD TC8220: Three Level High Speed ±100V 3.0A Pulser Demoboard. Waveform Generator CPLD.

Supertex inc. MD1822DB3. MD TC8220: Three Level High Speed ±100V 3.0A Pulser Demoboard. Waveform Generator CPLD. MD8 + TC8: Three Level High Speed ±V.A Pulser Demoboard MD8DB Demoboard Features Ultrasound high voltage & high current RTZ pulser MD8 driving TC8 with two pairs of MOSFETs -level voltage pulse waveform

More information

XR FSK Modem Filter FUNCTIONAL BLOCK DIAGRAM GENERAL DESCRIPTION FEATURES ORDERING INFORMATION APPLICATIONS SYSTEM DESCRIPTION

XR FSK Modem Filter FUNCTIONAL BLOCK DIAGRAM GENERAL DESCRIPTION FEATURES ORDERING INFORMATION APPLICATIONS SYSTEM DESCRIPTION FSK Modem Filter GENERAL DESCRIPTION FUNCTIONAL BLOCK DIAGRAM The XR-2103 is a Monolithic Switched-Capacitor Filter designed to perform the complete filtering function necessary for a Bell 103 Compatible

More information

Logosol Intelligent Hall-Servo Drive LS-173U Doc # / Rev. C, 02/12/2008

Logosol Intelligent Hall-Servo Drive LS-173U Doc # / Rev. C, 02/12/2008 Features Specially designed for control of brushless motors without encoder Hall-Servo and Encoder-Servo control modes Motors supported: - Brushless 60/120 commutated (AC) - Brush-commutated (DC) Up to

More information

LSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/CSI UL A800 FEATURES: LSI Computer Systems, Inc. 1 Walt Whitman Road, Melville, NY 114 (1) 1-0400 FAX (1) 1-040 STEPPER MOTOR CONTROLLER Controls Bipolar and Unipolar Motors Cost-effective replacement

More information

Simple Bridge Stand Alone H-Bridge Data Sheet Revision 1 August 2005

Simple Bridge Stand Alone H-Bridge Data Sheet Revision 1 August 2005 Simple Bridge Stand Alone H-Bridge Revision August 00 SOLUTIONS CUBED, LLC East First Street Chico, CA 99 phone: 0.9.0 fax: 0.9. www.solutions-cubed.com Copyright 00, LLC Simple Bridge Page Table of Contents.0

More information

Design and Implementation of Automatic Phase Changer for the Distribution Network using PIC Micro Controller 16F877A

Design and Implementation of Automatic Phase Changer for the Distribution Network using PIC Micro Controller 16F877A Design and Implementation of Automatic Phase Changer for the Distribution Network using PIC Micro Controller 16F877A S.Vithiya1, M.Tharanee2, N.Swappana3, G.Subbulakshmi4 UG Student, Dept. of EEE, K.Ramakrishnan

More information

CV Arpeggiator Rev 1. Last updated

CV Arpeggiator Rev 1. Last updated CV Arpeggiator Rev Last updated 6--20 The CV Arpeggiator is a modular synth project used for creating arpeggios of control voltage. It utilizes a custom programmed PIC 6F685 micro controller. It includes

More information

DISCONTINUED PRODUCT 8902 A REPLACED BY A8904SLB & A8904SLP 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING FEATURES

DISCONTINUED PRODUCT 8902 A REPLACED BY A8904SLB & A8904SLP 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING FEATURES MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING Data Sheet 26301.2 LOAD SUPPLY CD2 C WD C ST OUTA GROUND GROUND OUT B OUT C CENTERTAP BRAKE C RES 1 2 3 4 5 6 7 8 9 10 11 12 V BB COMMUTATION DELAY BOOST CHARGE

More information

PIC-SERVO SC (v.10) Servo Motion Control I.C.

PIC-SERVO SC (v.10) Servo Motion Control I.C. PIC-SERVO SC (v.10) Servo Motion Control I.C. Servo controller for D.C. motors (brush or brushless) with incremental encoder feedback Serial interface connects to RS232, RS485 or RS422 communications ports

More information

The NMIH-0050 H-Bridge

The NMIH-0050 H-Bridge The NMIH-0050 H-Bridge Features: 5 A continuous, 6 A peak current Supply voltages from 5.3V up to 40V Terminal block for power / motor Onboard LEDs for motor operation/direction Onboard LED for motor supply

More information

All drive and motor parameters are stored in nonvolatile. Features

All drive and motor parameters are stored in nonvolatile. Features Description Power Range The DigiFlex Performance (DP) Series digital servo drives are designed to drive brushed and brushless servomotors. These fully digital drives operate in torque, velocity, or position

More information

LV8716QAGEVK Evaluation Kit User Guide

LV8716QAGEVK Evaluation Kit User Guide LV8716QAGEVK Evaluation Kit User Guide NOTICE TO CUSTOMERS The LV8716QA Evaluation Kit is intended to be used for ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered

More information

PIC18F2X1X/4X1X. 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanowatt Technology. Flexible Oscillator Structure: Power-Managed Modes:

PIC18F2X1X/4X1X. 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanowatt Technology. Flexible Oscillator Structure: Power-Managed Modes: 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanowatt Technology Power-Managed Modes: Run: CPU On, Peripherals On Idle: CPU Off, Peripherals On Sleep: CPU Off, Peripherals Off Idle mode Currents

More information

B Robo Claw 2 Channel 25A Motor Controller Data Sheet

B Robo Claw 2 Channel 25A Motor Controller Data Sheet B0098 - Robo Claw 2 Channel 25A Motor Controller Feature Overview: 2 Channel at 25A, Peak 30A Hobby RC Radio Compatible Serial Mode TTL Input Analog Mode 2 Channel Quadrature Decoding Thermal Protection

More information

Operational Description

Operational Description Operational Description Wallterminal WT2000 ISO Tagit The Wallterminal WT2000 consists of the two components control unit and reader unit. The control unit is usually mounted in a save area inside the

More information

ST12 CODEC IR/RF Remote Control Encoder/Decoder IC 1. Overview

ST12 CODEC IR/RF Remote Control Encoder/Decoder IC 1. Overview ST CODEC / Remote Control Encoder/Decoder IC. Overview ST CODEC is Radio Frequency and Infrared encoder/decoder IC for remote control applications having unique features and flexibility not available with

More information

4 Channel RF Remote Controller with Momentary Outputs

4 Channel RF Remote Controller with Momentary Outputs 4 Channel RF Remote Controller with Momentary Outputs 4 Channel RF remote built using PT2262 and PT2272 IC from Princeton technology. PT2262 used as Encoder (Transmitter) and PT2262 Decoder (Receiver)

More information

DigiFlex Performance Servo Drive DZCANTE-020L080

DigiFlex Performance Servo Drive DZCANTE-020L080 Description Power Range The DZCANTE-020L080 digital servo drive is designed to drive brushed and brushless servomotors, stepper motors, and AC induction motors from a compact form factor ideal for embedded

More information

Digital Proportional Remote Controller. Digital proportional Remote Controller. Application Notes. Page 1

Digital Proportional Remote Controller. Digital proportional Remote Controller. Application Notes. Page 1 查询 PT8A995P 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 Digital Proportional Remote Controller Digital proportional Remote Controller Application Notes Page 1 Why proportional control Simple action control Proportional

More information

Preliminary Rev. M Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator

Preliminary Rev. M Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator Features Extremely low close-in phase noise, designed for professional Audiophile & Recording application. Typical -100dBc @ 10Hz at

More information

Hardware Flags. and the RTI system. Microcomputer Architecture and Interfacing Colorado School of Mines Professor William Hoff

Hardware Flags. and the RTI system. Microcomputer Architecture and Interfacing Colorado School of Mines Professor William Hoff Hardware Flags and the RTI system 1 Need for hardware flag Often a microcontroller needs to test whether some event has occurred, and then take an action For example A sensor outputs a pulse when a model

More information

A3977. Microstepping DMOS Driver with Translator

A3977. Microstepping DMOS Driver with Translator Features and Benefits ±2.5 A, 35 V output rating Low r DS(on) outputs, 0.45 Ω source, 0.36 Ω sink typical Automatic current decay mode detection/selection 3.0 to 5.5 V logic supply voltage range Mixed,

More information

PAM2421 EVB User Guide

PAM2421 EVB User Guide EV Board User Guide AE Department 1. Revision Information PAM2421 Date Revision Description Comment 2011/09 V1.0 Initial Release 2. PAM2804 General Description The PAM2421 devices are high-performance,

More information

MP2482 5A, 30V, 420kHz Step-Down Converter

MP2482 5A, 30V, 420kHz Step-Down Converter The Future of Analog IC Technology DESCRIPTION The MP2482 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 5A continuous output current over a wide input

More information

A5976. Microstepping DMOS Driver with Translator

A5976. Microstepping DMOS Driver with Translator FEATURES AND BENEFITS ±2.8 A, 40 V output rating Low R DS(on) outputs, 0.22 Ω source, 0.15 Ω sink typical Automatic current decay mode detection/selection 3 to 5.5 V logic supply voltage range Mixed, fast,

More information

PRELIMINARY AVB250A060 PRELIMINARY. Servo Drive. Peak Current (10 seconds)

PRELIMINARY AVB250A060 PRELIMINARY. Servo Drive. Peak Current (10 seconds) Description Power Range The servo amplifiers are designed to drive brushless DC motors at a high switching frequency for vehicle applications. t is fully protected against over-voltage, over-current, over-heating,

More information

Current-Mode PWM Multiple Output Flyback Converter

Current-Mode PWM Multiple Output Flyback Converter Introduction Current-Mode PWM Multiple Output Flyback Converter The Supertex evaluation board demonstrates the features of HV606 IC by presenting a DC/DC converter employing flyback technique to achieve

More information

MP A, 30V, 420kHz Step-Down Converter

MP A, 30V, 420kHz Step-Down Converter The Future of Analog IC Technology DESCRIPTION The MP28490 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 5A continuous output current over a wide input

More information

Variateur analogique courant continu série AZ et AZB

Variateur analogique courant continu série AZ et AZB Variateur analogique courant continu série AZ et AZB AZ Analog Drives for servo systems - AMC Advanced Motion Control www.rosier.fr 07/11/2011 page(s) 1-7 Products and System Requirements / Analog PWM

More information

BMC040. Dual Logic. Last updated

BMC040. Dual Logic. Last updated BMC040. Dual Logic. Last updated 2-1-2016 If you have any questions, or need help trouble shooting, please e-mail Michael@Bartonmusicalcircuits.com I Overview/Features II Schematic III Construction A.Parts

More information

DRV8801 Single Brushed DC Motor Driver Carrier

DRV8801 Single Brushed DC Motor Driver Carrier Overview DRV8801 Single Brushed DC Motor Driver Carrier DRV8801 single brushed DC motor driver carrier with dimensions. Texas Instruments DRV8801 is a tiny H-bridge motor driver IC that can be used for

More information

Servo Systems Co. 53 Green Pond Road, Suite #2 Rockaway, NJ (973) Toll Free: (800) Fax: (973)

Servo Systems Co. 53 Green Pond Road, Suite #2 Rockaway, NJ (973) Toll Free: (800) Fax: (973) Description Power Range servo amplifiers are designed to drive brushless DC motors at a high switching frequency for vehicle applications. It is fully protected against overvoltage, over-current, over-heating,

More information

MEGORAS Technology - TB6600 STEP MOTOR Driver.

MEGORAS Technology - TB6600 STEP MOTOR Driver. MEGORAS Technology - TB6600 STEP MOTOR Driver MEGORAS Technology - TB6600 STEP MOTOR Driver BOM SR. QNTY. REF. DESC. 1 6 CN1,CN2,CN3,CN4,CN5,CN8 2 PIN SCREW TERMINAL 2 1 CN6 3 PIN HEADER CONNECTOR 3 1

More information

HM8113B. 3A,4.5V-16V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION

HM8113B. 3A,4.5V-16V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION 3A,4.5-16 Input,500kHz Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 500KHz Frequency Operation 3A Output Current No Schottky Diode Required 4.5 to 16 Input oltage Range 0.6 Reference

More information

QUASAR PROJECT KIT # /24 HOUR GIANT CLOCK

QUASAR PROJECT KIT # /24 HOUR GIANT CLOCK This project was originally published in the electronics magazine, Silicon Chip, a few years ago. It is issued here as a kit with permission. Some modifications to the original published circuit and software

More information

PS2-SMC-06 Servo Motor Controller Interface

PS2-SMC-06 Servo Motor Controller Interface PS2-SMC-06 Servo Motor Controller Interface PS2-SMC-06 Full Board Version PS2 (Playstation 2 Controller/ Dual Shock 2) Servo Motor Controller handles 6 servos. Connect 1 to 6 Servos to Servo Ports and

More information

Bill of Materials: PWM Stepper Motor Driver PART NO

Bill of Materials: PWM Stepper Motor Driver PART NO PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,

More information

2A,4.5V-21V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION

2A,4.5V-21V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION 2A,4.5-21 Input,500kHz Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 500KHz Frequency Operation 2A Output Current No Schottky Diode Required 4.5 to 21 Input oltage Range 0.8 Reference

More information

Electronics Design Laboratory Lecture #10. ECEN 2270 Electronics Design Laboratory

Electronics Design Laboratory Lecture #10. ECEN 2270 Electronics Design Laboratory Electronics Design Laboratory Lecture #10 Electronics Design Laboratory 1 Lessons from Experiment 4 Code debugging: use print statements and serial monitor window Circuit debugging: Re check operation

More information

The CYF115 transmitter solution is ideal for industrial and consumer applications where simplicity and form factor are important.

The CYF115 transmitter solution is ideal for industrial and consumer applications where simplicity and form factor are important. CYF115 Datasheet 300M-450MHz RF Transmitter General Description The CYF115 is a high performance, easy to use, single chip ASK Transmitter IC for remote wireless applications in the 300 to 450MHz frequency

More information

Enpirion EN6360QI 8A DC/DC Converter w/integrated Inductor Evaluation Board

Enpirion EN6360QI 8A DC/DC Converter w/integrated Inductor Evaluation Board January 0 Enpirion EN660QI 8 DC/DC Converter w/integrated Inductor Evaluation Board Introduction Thank you for choosing Enpirion, the source for Ultra small foot print power converter products! The EN660QI

More information

36V, 1MHz, 0.6A Step-Down Converter With 35μA Quiescent Current VOUT 3.3V/0.6A

36V, 1MHz, 0.6A Step-Down Converter With 35μA Quiescent Current VOUT 3.3V/0.6A The Future of Analog IC Technology MP4566 36, 1MHz, 0.6A Step-Down Converter With 35μA Quiescent Current DESCRIPTION The MP4566 is a high frequency (1MHz) stepdown switching regulator with integrated internal

More information

DUAL STEPPER MOTOR DRIVER

DUAL STEPPER MOTOR DRIVER DUAL STEPPER MOTOR DRIVER GENERAL DESCRIPTION The is a switch-mode (chopper), constant-current driver with two channels: one for each winding of a two-phase stepper motor. is equipped with a Disable input

More information

MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter

MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter The Future of Analog IC Technology MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter DESCRIPTION The MP2313 is a high frequency synchronous rectified step-down switch mode converter

More information

B RoboClaw 2 Channel 30A Motor Controller Data Sheet

B RoboClaw 2 Channel 30A Motor Controller Data Sheet B0098 - RoboClaw 2 Channel 30A Motor Controller (c) 2010 BasicMicro. All Rights Reserved. Feature Overview: 2 Channel at 30Amp, Peak 60Amp Battery Elimination Circuit (BEC) Switching Mode BEC Hobby RC

More information

BOOST/BUCK-BOOST/BUCK/CONTROLLER IC with External MOSFET

BOOST/BUCK-BOOST/BUCK/CONTROLLER IC with External MOSFET BOOST/BUCK-BOOST/BUCK/CONTROLLER IC with External MOSFET FEATURES 5-60V input voltage range Single resistor programmable constant current driver Excellent constant current accuracy ±3% typically 0.1V feedback

More information

AMC A Power LED Driver

AMC A Power LED Driver Reference Design AMC7150 1.5A Power LED Driver Content 1. AMC7150 EM User Guide 2. Application of AMC7150 @ IN =12 DC 3. Application of AMC7150 @ IN =24 DC 4. Application of AMC7150 for MR16 5. PWM Dimming

More information

BMC029. Single Multiplier/Divider Last updated

BMC029. Single Multiplier/Divider Last updated BMC029. Single Multiplier/Divider Last updated 1-4-2015 I Features -What it does/controls -Demos II Schematics -Pinout -Controls -Inputs -Output III Construction -Parts List -PCB information -How to Install

More information

MP V, 4A Synchronous Step-Down Coverter

MP V, 4A Synchronous Step-Down Coverter MP9151 20, 4A Synchronous Step-Down Coverter DESCRIPTION The MP9151 is a synchronous rectified stepdown switch mode converter with built in internal power MOSFETs. It offers a very compact solution to

More information

Motor Control Demonstration Lab

Motor Control Demonstration Lab Motor Control Demonstration Lab JIM SIBIGTROTH and EDUARDO MONTAÑEZ Freescale Semiconductor launched by Motorola, 8/16 Bit MCU Division, Austin, TX 78735, USA. Email: j.sibigtroth@freescale.com eduardo.montanez@freescale.com

More information

LS7362 BRUSHLESS DC MOTOR COMMUTATOR / CONTROLLER

LS7362 BRUSHLESS DC MOTOR COMMUTATOR / CONTROLLER LS7362 BRUSHLESS DC MOTOR COMMUTATOR / CONTROLLER FEATURES: Speed control by Pulse Width Modulating (PWM) only the low-side drivers reduces switching losses in level converter circuitry for high voltage

More information

Counter/Timers in the Mega8

Counter/Timers in the Mega8 Counter/Timers in the Mega8 The mega8 incorporates three counter/timer devices. These can: Be used to count the number of events that have occurred (either external or internal) Act as a clock Trigger

More information