TABLE OF CONTENTS. Report No.: BL-SZ

Transcription

1

2 Revision History Version Issue Date Revisions Content Rev. 01 Jul. 20, 2017 Initial Issue Rev. 02 Aug. 02, 2017 Update the test method in section and other changes Rev. 03 Rev. 04 Aug. 07, 2017 Aug. 10, 2017 Update the test result of adaptivity on page 62. Add the information of software in section 3.2. TABLE OF CONTENTS 1 ADMINISTRATIVE DATA (GENERAL INFORMATION) Identification of the Testing Laboratory Identification of the Responsible Testing Location Laboratory Condition Announce PRODUCT INFORMATION Applicant Information Manufacturer Information Factory Information General Description for Equipment under Test (EUT) Ancillary Equipment Description of Support Units Technical Information Additional Instructions UMMARY OF TEST RESULTS GENERAL TEST CONFIGURATIONS Test Environments Test Equipment List Test Software List MEASUREMENT UNCERTAINTY Description of Test Setup For Conducted Test For Radiated Test For Dynamic Frequency Selection (DFS) Test /66

3 4.5.4 For Adaptivity Test For Receiver Blocking Test Test Type and Test Results Transmitter Parameters Centre frequencies Nominal Channel Bandwidth and Occupied Channel Bandwidth RF output power Power density Transmitter unwanted emissions outside the 5 GHz RLAN bands Transmitter unwanted emissions within the 5 GHz RLAN bands Receiver Parameters Receiver Spurious Emissions Dynamic Frequency Selection (DFS) Adaptivity (Channel Access Mechanism) Receiver Blocking User Access Restrictions Geo-location capability ANNEX A TEST RESULT A.1 Centre frequencies A.2 Nominal Channel Bandwidth and Occupied Channel Bandwidth A.3 RF output power...39 A.4 Power density A.5 Transmitter unwanted emissions outside the 5 GHz RLAN bands...43 A.6 Transmitter unwanted emissions within the 5 GHz RLAN bands A.7 Receiver Spurious Emissions A.8 Dynamic Frequency Selection (DFS) A.9 Adaptivity (Channel Access Mechanism)...59 A.10 Receiver Blocking ANNEX B TEST SETUP PHOTOS...65 ANNEX C EUT EXTERNAL PHOTOS ANNEX D EUT INTERNAL PHOTOS /66

4 1 ADMINISTRATIVE DATA (GENERAL INFORMATION) 1.1 Identification of the Testing Laboratory Company Name Address Phone Number Shenzhen BALUN Technology Co., Ltd. Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1.2 Identification of the Responsible Testing Location Test Location Address Accreditation Certificate Description Shenzhen BALUN Technology Co., Ltd. Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers of test site are 11524A-1. The laboratory has been listed by US Federal Communications Commission to perform electromagnetic emission measurements. The recognition numbers of test site are The laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC The accreditation certificate number is L6791. All measurement facilities used to collect the measurement data are located at Block B, FL 1, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Laboratory Condition Ambient Temperature 20 to 25 Ambient Relative Humidity Ambient Pressure 1.4 Announce 45% - 55% 100 kpa kpa (1) The test report reference to the report template version v1.1. (2) The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. (3) The test report is invalid if there is any evidence and/or falsification. (4) The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. (5) This document may not be altered or revised in any way unless done so by BALUN and all revisions are duly noted in the revisions section. (6) Content of the test report, in part or in full, cannot be used for publicity and/or promotional purposes without prior written approval from the laboratory. 4/66

5 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant TP-Link Technologies Co., Ltd. Address Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China 2.2 Manufacturer Information Manufacturer TP-Link Technologies Co., Ltd. Address 2.3 Factory Information Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Factory Address N/A N/A 2.4 General Description for Equipment under Test (EUT) EUT Type AC1200 Wireless Dual Band Router Model Name Under Test Series Model Name Description of Model name differentiation Hardware Version Software Version Network and Wireless connectivity Archer C50 N/A N/A N/A N/A WIFI a, b, g, n(HT20/40) and ac 5/66

6 2.5 Ancillary Equipment Ancillary Equipment 1 Ancillary Equipment 2 Ancillary Equipment 3 Adapter 1 Brand Name TP-Link Model No. T C1 (EU) Note Serial No. N/A Rated Input V, 300 ma, 50/60 Hz Rated Output 9 V, 850 ma Adapter 2 Brand Name TP-Link Model No. T D1(UK) Note Serial No. N/A Rated Input V, 300 ma, 50/60 Hz Rated Output 9 V, 850 ma Adapter 3 Brand Name TP-Link Model No. T E1(AU) Note Serial No. N/A Rated Input V, 300 ma, 50/60 Hz Rated Output 9 V, 850 ma Note: The adapter are same with electrical parameters and internal circuit structure, only differ in model name and adapter plug, T C1 (EU Plug) as the main for tested in this report. 2.6 Description of Support Units Description Manufacturer Model Serial No. Cal. Date Cal. Due Mobile phone Nubia NX531J SRD /66

7 2.7 Technical Information Frequency Range Low Sub-band: 5.15 GHz 5.35 GHz Modulation technology Modulation Type Transfer Rate (Mbps) (Single RF path) Equipment Type (LBT / non- LBT) Antenna Type OFDM a/ n: 64QAM, 16QAM, BPSK, QPSK ac:256QAM, 64QAM, 16QAM, BPSK, QPSK a: 54/ 48/ 36 / 24 / 18 /12/ 9/ 6 Mbps ac: up to VHT-MCS9 Adaptive equipment LBT based Detect and Avoid Dipole Antenna Antenna Gain ANT0 ANT1 Adaptive Adaptive or non-adaptive The Max RF Output power Receiver Category 2.74 dbi 2.99 dbi Adaptive 22.6 dbm Master without radar detection Low Sub-band: 5.15 GHz 5.35 GHz 8 channels are provided for a, ac (20MHz): Channel Center Frequency(MHz) channels are provided for ac (40MHz): Channel Center Frequency(MHz) 2 channels are provided for ac (80MHz): Channel Center Frequency(MHz) Note: Preliminary tests were performed in different data rate in above table to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. 7/66

8 Test Items Mode Data Rate Modulation Technology Modulation Type Low Sub-band Channel 11a 6 OFDM BPSK 48/36 Center frequencies 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 Nominal Channel Bandwidth and Occupied Channel Bandwidth 11a 6 OFDM BPSK 48/36 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 11a 6 OFDM BPSK 48/36 RF output power 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 11a 6 OFDM BPSK 48/36 Power density 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 Transmitter unwanted emissions outside the 5 GHz RLAN bands Transmitter unwanted emissions within the 5 GHz RLAN bands 11a 6 OFDM BPSK 48/36 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 11a 6 OFDM BPSK 48/36 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 11a 6 OFDM BPSK 48/36 Receiver spurious emissions 11ac(20 MHz) 6.5 OFDM BPSK 48/36 11ac(40 MHz) 13.5 OFDM BPSK 46/38 11ac(80 MHz) V0 OFDM BPSK 42 Dynamic Frequency Selection (DFS) 11a 6 OFDM BPSK 48 11ac(80 MHz) V0 OFDM BPSK 46 8/66

9 Adaptivity (Channel Access Mechanism) 11a 6 OFDM BPSK 36 11ac(80 MHz) V0 OFDM BPSK 42 Receiver Blocking 11a 6 OFDM BPSK 36 User Access Restrictions / / / / / Geo-location capability / / / / / Note: The modulation of 11ac (20 MHz), 11ac (40 MHz) backward compatible with 11n (HT20), 11n (HT40), and the test results are basically the same with them, thus only the modulation of 11ac (20 MHz), 11ac (40 MHz) was evaluated in the report. Mode Low Sub-band Channel Channel Number Frequency (MHz) 11a LOW(H/ L) 48/ / ac20 LOW(H/ L) 48/ / ac40 LOW(H/ L) 46/ / ac80 LOW(H/ L) Note: The above EUT information in section 2.3 and 2.4 was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. 9/66

10 2.8 Additional Instructions EUT Software Settings: Mode Special software is used. The software provided by client to enable the EUT under transmission condition continuously at specific channel frequencies individually. And EUT is transmitting pseudo random data by itself. During testing. Channel and Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product. Power level setup in software Test Software Version ADB Mode Channel Soft Set Low 18 11a Middle 1A High 19 Low 18 11n20 Middle 1A High 19 11n40 Low 1D High 1E 11ac80 All 1E 10/66

11 3 UMMARY OF TEST RESULTS The EUT has been tested according to ETSI EN V2.1.1 ( ). No. Identity Document Title 1 ETSI EN V2.1.1 ( ) 5 GHz RLAN; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU Test items and the results are as follows: Report Section Standar d Rule Description Test Result Verdict Remark Center frequencies ANNEX A.1 Pass Nominal Channel Bandwidth and Occupied Channel Bandwidth ANNEX A.2 Pass RF output power ANNEX A.3 Pass Power density ANNEX A.4 Pass Transmitter unwanted emissions Transmitter unwanted emissions outside the 5 GHz RLAN bands Transmitter unwanted emissions within the 5 GHz RLAN bands ANNEX A.5 Pass -- ANNEX A.6 Pass Receiver spurious emissions ANNEX A.7 Pass Dynamic Frequency Selection (DFS) ANNEX A.8 N/A Adaptivity (Channel Access Mechanism) ANNEX A.9 Pass Receiver Blocking ANNEX A.10 Pass User Access Restrictions -- Note Geo-location capability -- Note 1 -- Note 1 : The function of User Access Restrictions and Geo-location capability is declared by manufacture, for more detailed description, please refer to the user manual. 11/66

12 4 GENERAL TEST CONFIGURATIONS 4.1 Test Environments During the measurement, the normal environmental conditions were within the listed ranges: Relative Humidity 45% - 55% Atmospheric Pressure 100 kpa kpa NT (Normal Temperature) +22 to +25 Temperature LT (Low Temperature) -10 HT (High Temperature) +40 NV (Normal Voltage) 230 V Working Voltage of the EUT LV (Low Voltage) 207 V HV (High Voltage) 240 V 4.2 Test Equipment List Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer ROHDE&SCHWARZ FSV Vector Signal Generator ROHDE&SCHWARZ SMBV100A Signal Generator ROHDE&SCHWARZ SMB100A Switch Unit with OSP-B157 ROHDE&SCHWARZ OSP Spectrum Analyzer AGILENT E4440A MY EMI Receiver ROHDE&SCHWARZ ESRP Power Splitter KMW DCPD-LDC Power Sensor ROHDE&SCHWARZ NRP-Z Attenuator (20 db) KMW ZA-S Attenuator (6 db) KMW ZA-S DC Power Supply ROHDE&SCHWARZ HMP Temperature ANGELANTIONI Chamber SCIENCE NTH64-40A Test Antenna- Loop(9 khz-30 MHz) SCHWARZBECK FMZB Test Antenna- Bi-Log(30 MHz-3 SCHWARZBECK VULB GHz) Test Antenna- BBHA SCHWARZBECK Horn(1-18 GHz) 9120D 9120D Test Antenna- Horn(15-40 GHz) SCHWARZBECK BBHA Anechoic Chamber RAINFORD 9m*6m*6m N/A Shielded Enclosure ChangNing CN Wireless Communications Test ROHDE&SCHWARZ CMW /66

13 4.3 Test Software List Description Manufacturer Software Version Serial No. TS8997 EMC32 ROHDE&SCHWARZ V N/A COT Test BALUN V1.0 N/A 4.4 MEASUREMENT UNCERTAINTY The following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Value RF frequency ±1*10-5 RF power conducted RF power, radiated Spurious emissions, conducted Spurious emissions, radiated Temperature ±1.5 db ±6 db ±3 db ±6 db ±1 C Humidity ±5 % Time ±10 % 13/66

14 4.5 Description of Test Setup For Conducted Test (Diagram 1) 14/66

15 4.5.2 For Radiated Test (Diagram 2) (Diagram 3) 15/66

16 4.5.3 For Dynamic Frequency Selection (DFS) Test (Diagram 4) For Adaptivity Test Spectrum Analyzer Analyerz UUT Splitter/ Combiner Splitter/ ATT. Companion Device Combiner Signal Generator Traffic (Interferer ) Source (Diagram 5) 16/66

17 PC COT Test Soft EMC32 Switch Control OSP-B157 Companion device EUT (Diagram 6) For Receiver Blocking Test (Diagram 7) 17/66

18 5 Test Type and Test Results 5.1 Transmitter Parameters Centre frequencies Limit The Nominal Centre Frequencies (fc) for a Nominal Channel Bandwidth of 20 MHz are defined by equation (1). fcn = (g 20) MHz, where 0 g 9 or 16 g 27 (1) A maximum offset of the Nominal Centre Frequency of ± 200 khz is permitted. Where the manufacturer decides to make use of this frequency offset, the manufacturer shall declare the actual centre frequencies used by the equipment. (See clause 5.4.1, item a). The actual centre frequency for any given channel shall be maintained within the range fc ± 20 ppm. Equipment may have simultaneous transmissions on more than one Operating Channel with a Nominal Channel Bandwidth of 20 MHz Test Setup The section (Diagram 1) test setup description was used for this test Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.1. 18/66

19 5.1.2 Nominal Channel Bandwidth and Occupied Channel Bandwidth Limit The Nominal Channel Bandwidth for a single Operating Channel shall be 20 MHz. Alternatively, equipment may implement a lower Nominal Channel Bandwidth with a minimum of 5 MHz, providing they still comply with the Nominal Centre Frequencies defined in clause (20 MHz raster). The Occupied Channel Bandwidth shall be between 80 % and 100 % of the Nominal Channel Bandwidth. In case of smart antenna systems (devices with multiple transmit chains) each of the transmit chains shall meet this requirement. The Occupied Channel Bandwidth might change with time/payload. During a Channel Occupancy Time (COT), equipment may operate temporarily with an Occupied Channel Bandwidth of less than 80 % of its Nominal Channel Bandwidth with a minimum of 2 MHz Test Setup The section (Diagram 1) test setup description was used for this test Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.2. 19/66

20 5.1.3 RF output power Limit The RF Output Power is the mean equivalent isotropically radiated power (e.i.r.p.) during a transmission burst. Transmit Power Control (TPC) is a mechanism to be used by the RLAN device to ensure a mitigation factor of at least 3 db on the aggregate power from a large number of devices. This requires the RLAN device to have a TPC range from which the lowest value is at least 6 db below the values for mean e.i.r.p. given in table 1 for devices with TPC. Limits for RF output power at the highest power level Mean e.i.r.p. limit (dbm) Frequency range (MHz) With TPC Without TPC 5150 to /23(see note 1) 5470 to (see note 2) 27(see note 2) Note 1 : The applicable limit is 20 dbm, except for transmissions whose nominal bandwidth falls completely within the band MHz to MHz, in which case the applicable limit is 23 dbm. Note 2 : Slave devices without a Radar Interference Detection function shall comply with the limits for the band MHz to MHz. Limit for RF output power at the lowest power level of the TPC range Frequency range (MHz) Mean e.i.r.p. limit (dbm) 5250 to to (see note) Note: Slave devices without a Radar Interference Detection function shall comply with the limits for the band MHz to MHz Test Setup The section (Diagram 1) test setup description was used for this test Test Procedure Reference to ETSI EN V2.1.1 clause and clause Test Result Please refer to ANNEX A.3. 20/66

21 5.1.4 Power density Limit The Power Density is the mean equivalent isotropically radiated power (e.i.r.p.) density during a transmission burst. Transmit Power Control (TPC) is a mechanism to be used by the RLAN device to ensure a mitigation factor of at least 3 db on the aggregate power from a large number of devices. This requires the RLAN device to have a TPC range from which the lowest value is at least 6 db below the values for mean e.i.r.p. given in table 1 for devices with TPC. Mean e.i.r.p. density limit (dbm/mhz) Frequency range (MHz) With TPC Without TPC 5150 to /10(see Note 1 ) 5470 to (see Note 2 ) 14(see Note 2 ) Note 1 : The applicable limit is 7 dbm/mhz, except for transmissions whose nominal bandwidth falls completely within the band MHz to MHz, in which case the applicable limit is 10 dbm/mhz. Note 2 : Slave devices without a Radar Interference Detection function shall comply with the limits for the band MHz to MHz Test Setup The section (Diagram 1) test setup description was used for this test Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.4. 21/66

22 5.1.5 Transmitter unwanted emissions outside the 5 GHz RLAN bands Limit The level of transmitter unwanted emissions outside the 5 GHz RLAN bands shall not exceed the limits given in next table. In case of equipment with antenna connectors, these limits apply to emissions at the antenna port (conducted) and to the emissions radiated by the cabinet. In case of integral antenna equipment (without temporary antenna connectors), these limits apply to emissions radiated by the equipment. Frequency range Maximum power (dbm) Bandwidth 30 MHz to 47 MHz khz 47 MHz to 74 MHz khz 74 MHz to 87.5 MHz khz 87.5 MHz to 118 MHz khz 118 MHz to 174 MHz khz 174 MHz to 230 MHz khz 230 MHz to 470 MHz khz 470 MHz to 862 MHz khz 862 MHz to 1 GHz khz 1 GHz to 26 GHz MHz Table : Transmitter unwanted emission limits outside the 5 GHz RLAN bands Test Setup See the section and (Diagram 1, 2, 3) for test setup description Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.5. 22/66

23 5.1.6 Transmitter unwanted emissions within the 5 GHz RLAN bands Limit The average level of the transmitted spectrum shall not exceed the limits given in the following figure: Figure 1: Transmit mask NOTE: dbc is the spectral density relative to the maximum spectral power density of the transmitted signal Test Setup The section (Diagram 1) test setup description was used for this test Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.6. 23/66

24 5.2 Receiver Parameters Receiver Spurious Emissions Limit Receiver spurious emissions are emissions at any frequency when the equipment is in receive mode. The spurious emissions of the transmitter shall not exceed the values in following tables for the EUT in this report. Frequency range Maximum power (dbm) Bandwidth 30 MHz to 1 GHz KHz 1 GHz to GHz MHz Test Setup See the section (Diagram 1) for test setup description Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.7. 24/66

25 5.2.2 Dynamic Frequency Selection (DFS) Limit The manufacturer shall state whether the UUT is capable of operating as a Master and/or a Slave. If the UUT is capable of operating in more than one operating mode then each operating mode shall be tested separately. See tables A for the applicability of DFS requirements for each of the operational modes. Operational Mode Requirement Slave (without radar Slave (with radar Master detection) detection) Channel Availability Check Required Not required Required (see Note 2) Off-Channel CAC (see note 1) Required Not required Required (see Note 2) In-Service Monitoring Required Not required Required Channel Shutdown Required Required Required Non-Occupancy Period Required Not required Required Uniform Spreading Required Not required Not required Note 1 : Where implemented by the manufacturer. Note 2 : A slave with radar detection is not required to perform a CAC or Off-Channel CAC at initial use of the channel but only after the slave has detected a radar signal on the Operating Channel by In-Service Monitoring and the Non-Occupancy Period resulting from this detection has elapsed. The radar detection requirements specified in clauses to assume that the centre frequencies of the radar signals fall within the central 80 % of the Occupied Channel Bandwidth of the RLAN channel. DFS requirement values Parameter Value Channel Availability Check Time 60 s (see Note 1) Minimum Off-Channel CAC Time 6 minutes (see Note 2) Maximum Off-Channel CAC Time 4 hours (see Note 2) Channel Move Time 10 s Channel Closing Transmission Time 1 s Non-Occupancy Period 30 minutes Note 1: For channels whose nominal bandwidth falls completely or partly within the band MHz to MHz, the Channel Availability Check Time shall be 10 minutes. Note 2: For channels whose nominal bandwidth falls completely or partly within the band MHz to MHz, the Off-Channel CAC Time shall be within the range 1 hour to 24 hours. 25/66

26 Interference threshold values e.i.r.p. Spectral Density Value (dbm/mhz) (see Note 1&2 ) dbm Note 1 : This is the level at the input of the receiver of an RLAN device with a maximum e.i.r.p. density of 10 dbm/mhz and assuming a 0 dbi receive antenna. For devices employing different e.i.r.p. spectral density and/or a different receive antenna gain G (dbi) the DFS threshold level at the receiver input follows the following relationship: DFS Detection Threshold (dbm) = e.i.r.p. Spectral Density (dbm/mhz) + G (dbi); however the DFS threshold level shall not be less than -64 dbm assuming a 0 dbi receive antenna gain. Note 2 : Slave devices with a maximum e.i.r.p. of less than 23 dbm do not have to implement radar detection unless these devices are used in fixed outdoor point to point or fixed outdoor point to multipoint applications (see clause ). Parameters of the reference DFS test signal Pulse width W [μs] Pulse repetition frequency PRF [PPS] Pulses per burst [PPB] Parameters of radar test signals Radar test Pulse repetition Number of Pulses per Pulse width signal # frequency different burst for each W [μs] (see Note 1 PRF (PPS) PRFs PRF (PPB) to Note 3 ) Min Max Min Max (see Note 5 ) (see Note 6 ) (see Note 6 ) /3 10 (see Note 6 ) /3 15 (see Note 6 ) Note 1 : Radar test signals #1 to #4 are constant PRF based signals. See figure D.1. These radar test signals are intended to simulate also radars using a packet based Staggered PRF. See figure D.2. Note 2 : Radar test signal #4 is a modulated radar test signal. The modulation to be used is a chirp modulation with a ±2,5 MHz frequency deviation which is described below. 26/66

27 Note 3 : Radar test signals #5 and #6 are single pulse based Staggered PRF radar test signals using 2 or 3 different PRF values. For radar test signal #5, the difference between the PRF values chosen shall be between 20 PPS and 50 PPS. For radar test signal #6, the difference between the PRF values chosen shall be between 80 PPS and 400 PPS. See figure D.3. Note 4 : Apart for the Off-Channel CAC testing, the radar test signals above shall only contain a single burst of pulses. See figure D.1, figure D.3 and figure D.4. For the Off-Channel CAC testing, repetitive bursts shall be used for the total duration of the test. See figure D.2 and figure D.5. See also clause , clause and clause Note 5 : The total number of pulses in a burst is equal to the number of pulses for a single PRF multiplied by the number of different PRFs used. Note 6 : For the CAC and Off-Channel CAC requirements, the minimum number of pulses (for each PRF) for any of the radar test signals to be detected in the band MHz to MHz shall be 18. Detection probability Detection Probability (Pd) Channels whose nominal bandwidth falls Parameter partly or completely within Other channels the MHz to MHz band CAC, Off-Channel CAC 99,99 % 60 % In-Service Monitoring 60 % 60 % NOTE: Pd gives the probability of detection per simulated radar burst and represents a minimum level of detection performance under defined conditions. Therefore Pd does not represent the overall detection probability for any particular radar under real life conditions Test Setup See the section (Diagram 4) for test setup description. 27/66

28 Test Procedure The measured channel shall test with the lowest and highest bandwidth. The radar signal was the same as transmitted channels, and injected into the antenna port of AP (master) with radar signal, measured the channel shutdown. The slave transmitted the test data to master. Specific test procedure please reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A.8. 28/66

29 5.2.3 Adaptivity (Channel Access Mechanism) Priority Classes Table 8 each contain four different sets of Channel Access parameters for Supervised Devices respectively, resulting in different Priority Classes and different maximum Channel Occupancy Times. If a Channel Occupancy consists of more than one transmission the transmissions may be separated by gaps. The Channel Occupancy Time is the total duration of all transmissions and all gaps of 25 µs duration or less within a Channel Occupancy and shall not exceed the maximum Channel Occupancy Time in table 8. The duration from the start of the first transmission within a Channel Occupancy until the end of the last transmission in that same Channel Occupancy shall not exceed 20 ms. Table 8: Priority Class dependent Channel Access parameters for Supervised Devices Class # P0 CWmin CWmax Maximum Channel Occupancy Time (COT) ms ms ms (see note 1) ms (see note 1) NOTE 1: The maximum Channel Occupancy Time (COT) of 6 ms may be increased to 8 ms by inserting one or more pauses. The minimum duration of a pause shall be 100 µs. The maximum duration (Channel Occupancy) before including any such pause shall be 6 ms. Pause duration is not included in the channel occupancy time. NOTE 2: The values for p0, CWmin, CWmax are minimum values. Greater values are allowed. 29/66

30 Limit This requirement applies to equipment, testing shall be performed using the combination/grouping of 20 MHz operating channels. The manufacturer shall state whether the UUT is capable of operating as a Frame Based Equipment or Load Based Equipment. See tables for the applicability of adaptive requirements and limit for each of the operational modes. Applicability of adaptive requirements and limit Requirement Initiating Device Channel Access Mechanism Frame Based Equipment Load Based Equipment Periods 1ms ~ 10ms 1ms ~ 10ms (see note 1) (see note 1) Maximum Channel Occupancy Time (COT) (see note 2) See Table 8 Minimum Idle Period 5 % COT and within 100 µs 5 % COT and within 100 µs Clear Channel Assessment (CCA) 16 µs 9μs<; <16μs Short Control Signaling Note 3 Note 3 Note 1: Declared by the manufacturer. Note 2: Different Priority Classes has different limit, please reference to table 8. Note 3: Within an observation period of 50 ms, the number of Short Control Signaling Transmissions by the equipment shall be equal to or less than 50ms, the total duration of the equipment's Short Control Signaling Transmissions shall be less than µs within said observation period. Interference Signals used for Adaptivity Tests Interference Signals Type Bandwidth Descriptions (MHz) AWGN 20 OFDM 20 Note 1 LTE 20 Note 1: All of interference signals shall be a continuous (100 % duty cycle), the OFDM signal as defined in IEEE [9], clause 17 and the LTE-type signal as described in ETSI TS [8], clause Interference threshold level The maximum transmit power (PH) Threshold level (TL) (see notes 1) Option dbm / MHz PH 13 dbm -75 dbm / MHz Option2 13 dbm < PH < 23 dbm -85 dbm/mhz + (23 dbm - PH) PH 23 dbm -85 dbm/mhz Note 1: The ED Threshold Level (TL), at the input of the receiver, shall be proportional to the maximum transmit power (PH) according to the formula which assumes a 0 dbi receive antenna and PH to be specified in dbm e.i.r.p. Test Setup See the section (Diagram 5) for test setup description. 30/66

31 For Maximum Channel Occupancy Time (COT) and minimum idle time Please the section (Diagram 6) for test setup description Test Procedure Reference to ETSI EN V2.1.1 clause For Maximum Channel Occupancy Time (COT) and minimum idle time Step 1: Connect to EUT according to diagram 6 Step 2: Make sure the EUT have traffic with a companion device Step 3: EMC32 software was only used for controlling the test path (OSP-B157) to power sensor Step 4: Running the COT Test soft by setting suitable time to monitor and record the COT and Idle time Step 5: Record the test data Test Result Please refer to ANNEX A.9. 31/66

32 5.2.4 Receiver Blocking Limit While maintaining the minimum performance criteria as defined in clause , the blocking levels at specified frequency offsets shall be equal to or greater than the limits defined in table 9. Blocking signal power (dbm) Wanted signal (see note 2) mean power Blocking signal Master or Slave with Slave without radar from companion frequency radar detection detection device (MHz) (see table D.2, (see table D.2, note (dbm) note 2) 2) Pmin + 6 db Pmin + 6 db Type of blocking signal Continuous Wave Continuous Wave NOTE 1: Pmin is the minimum level of the wanted signal (in dbm) required to meet the minimum performance criteria as defined clause in the absence of any blocking signal. NOTE 2: The levels specified are levels in front of the UUT antenna. In case of conducted measurements, the same levels should be used at the antenna connector irrespective of antenna gain Test Setup See the section (Diagram 7) for test setup description Test Procedure Reference to ETSI EN V2.1.1 clause Test Result Please refer to ANNEX A /66

33 5.2.5 User Access Restrictions Definition User Access Restrictions are restraints implemented in the RLAN to restrict access for the user to certain hardware and/or software settings of the equipment Requirement DFS controls (hardware or software) related to radar detection shall not be accessible to the user so that the DFS requirements described in clauses to can neither be disabled nor altered Test Result Please refer to section 3 note 1. 33/66

34 5.2.6 Geo-location capability Definition This requirement only applies to equipment with geo-location capability Geo-location capability is a feature of the RLAN device to determine its geographical location with the purpose to configure itself according to the regulatory requirements applicable at the geographical location where it operates. The geo-location capability may be present in the equipment or in an external device (temporary) associated with the equipment operating at the same geographical location during the initial power up of the equipment. The geographical location may also be available in equipment already installed and operating at the same geographical location Requirement The geographical location determined by the equipment as defined in clause shall not be accessible to the user Test Result Please refer to section 3 note 1. 34/66

35 ANNEX A TEST RESULT A.1 Centre frequencies Measuring Parameter Centre Frequency The centre frequency of the channel under test RBW (MHz) 100 khz VBW (MHz) 300 khz Span (MHz) 20 MHz (for 20 MHz channel), 40 MHz (for 40 MHz channel) 80MHz(For 80MHz channel) Detector mode RMS Sweep Point Trace mode Max Hold Sweep time 1s Test Method Radiated Conducted Test Data Modulation Mode a Sub-band Low band Limit ±20 ppm Test Result Test Conditions Carrier Centre Frequencies fc (MHz) Temperature Voltage Low Channel High Channel Frequency (MHz) ppm Frequency (MHz) ppm NT NV LT LV HV HT LV HV Test Verdict Pass 35/66

36 Modulation Mode ac(20 MHz) Sub-band Low band Limit ±20 ppm Test Result Test Conditions Carrier Centre Frequencies fc (MHz) Temperature Voltage Low Channel High Channel Frequency (MHz) ppm Frequency (MHz) ppm NT NV LT LV HV HT LV HV Test Verdict Pass Modulation Mode ac(40 MHz) Sub-band Low band Limit ±20 ppm Test Result Test Conditions Carrier Centre Frequencies fc (MHz) Temperature Voltage Low Channel High Channel Frequency (MHz) ppm Frequency (MHz) ppm NT NV LT LV HV HT LV HV Test Verdict Pass Modulation Mode ac(80 MHz) Sub-band Low band Limit ±20 ppm Test Result Test Conditions Carrier Centre Frequencies fc (MHz) Temperature Voltage Low Channel Frequency (MHz) ppm NT NV LT LV HV HT LV HV Test Verdict Pass 36/66

37 A.2 Nominal Channel Bandwidth and Occupied Channel Bandwidth Measuring Parameter Centre Frequency The centre frequency of the channel under test RBW (MHz) 100 khz VBW (MHz) 300 khz Span (MHz) 40 MHz (for 20 MHz channel), 80 MHz (for 40 MHz channel) 160MHz(For 80MHz channel) Detector mode RMS Trace mode Max Hold Sweep time 2s Test Method Radiated Conducted Test Data Modulation Mode a Limit 16~20 MHz Test Result Test Conditions Occupied Bandwidth (MHz) Temperature Voltage Low Sub-band / Low Channel High Channel / / NT NV / / Test Verdict Pass Modulation Mode ac(20MHz) Limit 16~20 MHz Test Result Test Conditions Occupied Bandwidth (MHz) Temperature Voltage Low Sub-band / Low Channel High Channel / / NT NV / / Test Verdict Pass Modulation Mode ac(40MHz) Limit 32~40 MHz Test Result Test Conditions Occupied Bandwidth (MHz) Temperature Voltage Low Sub-band / Low Channel High Channel / / NT NV / / Test Verdict Pass 37/66

38 Modulation Mode ac(80MHz) Limit 64~80 MHz Test Result Test Conditions Occupied Bandwidth (MHz) Temperature Voltage Low Sub-band / Low Channel / / / NT NV 75.6 / / / Test Verdict Pass 38/66

39 A.3 RF output power Test Data Note 1 : The applicable limit is 20 dbm, except for transmissions whose nominal bandwidth falls completely within the band MHz to MHz, in which case the applicable limit is 23 dbm. Note 2 : This product does not support TPC function. Modulation Mode a Low Sub-band 20/23(see note 1) dbm Limit High Sub-band 27 dbm Test Result Test Method Test Conditions EIRP (dbm) Low Sub-band / Temperature Voltage Low High / / Channel Channel Radiated Conducted NT NV / / LT LV / / HV / / HT LV / / HV / / Test Verdict Pass Modulation Mode ac(20 MHz) Low Sub-band 20/23(see note 1) dbm Limit High Sub-band 27 dbm Test Result Test Method Test Conditions EIRP (dbm) Low Sub-band / Temperature Voltage Low High / / Channel Channel Radiated Conducted NT NV / / LT LV / / HV / / HT LV / / HV / / Test Verdict Pass 39/66

40 Modulation Mode ac(40 MHz) Low Sub-band 20/23(see note 1) dbm Limit High Sub-band 27 dbm Test Result Test Method Test Conditions EIRP (dbm) Low Sub-band / Temperature Voltage Low High / / Channel Channel Radiated Conducted NT NV / / LT LV / / HV / / HT LV / / HV / / Test Verdict Pass Modulation Mode ac(80 MHz) Low Sub-band 20/23(see note 1) dbm Limit High Sub-band 27 dbm Test Result Test Method Test Conditions EIRP (dbm) Low Sub-band / Temperature Voltage Low / / / Channel Radiated Conducted NT NV 22.6 / / / LT LV 22.6 / / / HV 22.5 / / / HT LV 22.6 / / / HV 22.4 / / / Test Verdict Pass 40/66

41 A.4 Power density Measuring Parameter RBW (MHz) 1 MHz VBW (MHz) 3 MHz Sweep points Detector mode RMS Span 40 MHz (for 20 MHz channel), 80 MHz (for 40 MHz channel), 160 MHz (for 80 MHz channel) Trace mode Max Hold Sweep time Auto Test Method Radiated Conducted Test Data Modulation Mode a Low Sub-band 7 dbm/mhz Limit High Sub-band 10 dbm/mhz Test Result Test Conditions Power density (dbm/mhz) Temperatur Low Sub-band / Voltage e Low Channel High Channel / / NT NV / / Test Verdict Pass Modulation Mode ac(20 MHz) Low Sub-band 7 dbm/mhz Limit High Sub-band 10 dbm/mhz Test Result Test Conditions Power density (dbm/mhz) Low Sub-band / Temperature Voltage Low Channel High Channel / / NT NV / / Test Verdict Pass Modulation Mode ac(40 MHz) Low Sub-band 7 dbm/mhz Limit High Sub-band 10 dbm/mhz Test Result Test Conditions Power density (dbm/mhz) Low Sub-band / Temperature Voltage Low Channel High Channel / / NT NV / / Test Verdict Pass 41/66

42 Modulation Mode ac(80 MHz) Low Sub-band 7 dbm/mhz Limit High Sub-band 10 dbm/mhz Test Result Test Conditions Power density (dbm/mhz) Low Sub-band / Temperature Voltage Low Channel / / / NT NV 5.3 / / / Test Verdict Pass 42/66

43 A.5 Transmitter unwanted emissions outside the 5 GHz RLAN bands Note: The Frequency band was pre-scanned, the harmonic and other spurious which worst frequency are recorded in the report. Measuring Parameter Frequency Range 30 MHz to MHz 1 GHz to 26 GHz RBW 100 khz VBW 300 khz Sweep points 9700 Detector mode Peak Trace mode Max Hold RBW 1 MHz VBW 3 MHz Sweep points Detector mode Peak Trace mode Max Hold Conducted Test Data Modulation Mode a Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Tx: Low Sub-band, High Channel Modulation Mode ac(20 MHz) 43/66

44 Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Tx: Low Sub-band, High Channel /66

45 Modulation Mode Test Condition ac(40 MHz) Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Tx: Low Sub-band, High Channel Modulation Mode Test Condition ac(80 MHz) Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel /66

46 Cabinet Radiated spurious emission test data Note: The device was evaluated/tested in XYZ orientation for radiated spurious emissions. And only the worst orientation of EUT was reported, which is the horizontal orientation. Modulation Mode a Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Antenna Polarization: Vertical Tx:Low Sub-band, Low Channel Antenna Polarization: Horizontal Tx:Low Sub-band, High Channel Antenna Polarization: Vertical Tx:Low Sub-band, High Channel Antenna Polarization: Horizontal Modulation Mode ac(20 MHz) 46/66

47 Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Antenna Polarization: Vertical Tx:Low Sub-band, Low Channel Antenna Polarization: Horizontal Tx:Low Sub-band, High Channel Antenna Polarization: Vertical Tx:Low Sub-band, High Channel Antenna Polarization: Horizontal /66

48 Modulation Mode Test Condition ac(40 MHz) Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Antenna Polarization: Vertical Tx:Low Sub-band, Low Channel Antenna Polarization: Horizontal Tx:Low Sub-band, High Channel Antenna Polarization: Vertical Tx:Low Sub-band, High Channel Antenna Polarization: Horizontal /66

49 Modulation Mode Test Condition ac(80 MHz) Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Transmitter Operating Mode Tx:Low Sub-band, Low Channel Antenna Polarization: Vertical Tx:Low Sub-band, Low Channel Antenna Polarization: Horizontal /66

50 A.6 Transmitter unwanted emissions within the 5 GHz RLAN bands Measuring Parameter(For equipment with continuous transmission capability) RBW (MHz) 1 MHz VBW (MHz) 30 khz Detector mode Peak Trace mode Video Average Sweep time Coupled Test Method Radiated Conducted Test Plots a Low Sub-band, Low channel a Low Sub-band, High channel 50/66

51 802.11ac(20 MHz) Low Sub-band, Low channel ac(20 MHz) Low Sub-band, High channel 51/66

52 802.11ac(40 MHz) Low Sub-band, Low channel ac(40 MHz) Low Sub-band, High channel 52/66

53 802.11ac(80 MHz) Low Sub-band, Low channel 53/66

54 A.7 Receiver Spurious Emissions Note 1 : The test method choose the conducted method. Which power in a specified load (conducted spurious emissions) and their effective radiated power when radiated by the cabinet or structure of the equipment (cabinet radiation). Note 2 : The Frequency band was pre-scanned, the harmonic and other spurious which worst frequency are recorded in the report. Measuring Parameter Frequency Range RBW (MHz) 100 khz VBW (MHz) 300 khz 30 MHz to MHz Sweep points 9700 Detector mode Peak Trace mode Max Hold RBW (MHz) 1 MHz VBW (MHz) 3 MHz 1 GHz to 26 GHz Sweep points Detector mode Peak Trace mode Max Hold Conducted Test Data Modulation Mode a Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Receiver Operating Mode Rx:Low Sub-band, Low Channel Rx:Low Sub-band, High Channel Modulation Mode ac(20 MHz) 54/66

55 Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Receiver Operating Mode Rx:Low Sub-band, Low Channel Rx:Low Sub-band, High Channel /66

56 Modulation Mode Test Condition ac(40 MHz) Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Receiver Operating Mode Rx:Low Sub-band, Low Channel Rx:Low Sub-band, High Channel Modulation Mode Test Condition ac Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Receiver Operating Mode Rx:Low Sub-band, Low Channel /66

57 Cabinet Radiation Test Data Note 1 : All the configuration were tested, but only the worst data (802.11ac80) were reported in this report. Note 2 : The device was evaluated/tested in XYZ orientation for radiated spurious emissions. And only the worst orientation of EUT was reported, which is the horizontal orientation. Test Condition Temperature NT, Voltage NV No. Frequency (MHz) Level (dbm) Limit (dbm) Margin (db) Receiver Operating Mode Antenna Polarization: Vertical Antenna Polarization: Horizontal /66

58 A.8 Dynamic Frequency Selection (DFS) Note: Not applicable. 58/66

59 A.9 Adaptivity (Channel Access Mechanism) List of Measurements UUT Operational Mode Pulse width W [μs] Pulse repetition frequency PRF [PPS] Pulses per burst [PPB] Test Method Clause Test Parameter Remarks Pass/Fail Adaptive (Frame Based Equipment) Not Applicable N/A Radiated Adaptive (Load Based Conducted Equipment) Applicable Pass Short Control Signaling Transmissions Applicable Pass Interference Signals used for Adaptively Tests Interference Signals Type Bandwidth Descriptions (MHz) AWGN 20 OFDM 20 Note 1 LTE 20 Note 1: The three interference signals was tested, only the worst result of interference signal (AWGN) was shown in the test report. Energy Detection Threshold Level (TL) Type of Interference threshold level equipment The ED Threshold level (TL) = -75 dbm/mhz (assumes a 0 dbi receive antenna) and Option 1 antenna gain is 1.8 dbi. Option 2 The ED Threshold level (TL) = -75 dbm/mhz + G (1.8 dbi) = dbm/mhz 59/66

60 Test plots AWGN Signal OFDM Signal LTE Signal Result of Measurements (For Priority Class 1) 60/66

61 The Maximum Channel Occupancy Time (COT) and Minimum Idle period time For Supervising Device Modulation Frequency Maximum Channel Occupancy (MHz) Time (ms) Limit (ms) Verdict 11a(20MHz) Pass 11ac(80MHz) Pass Modulation Frequency Minimum Idle Period (us) (MHz) Limit (us) Verdict 11a(20MHz) Pass 11ac(80MHz) Pass The COT Times List: Note: The COT was monitored at least times, but only the nearly maximum channel occupancy and minimum idle period was list here a (20 MHz) Channel 36 NO. of COT Burst RMS Power Start Time Stop Time (dbm) (ms) (ms) Channel Occupancy Time (ms) Idle Period (us) ac (80 MHz) Channel 42 NO. of COT Burst RMS Power Start Time Stop Time (dbm) (ms) (ms) Channel Occupancy Time (ms) Idle Period (us) /66

62 802.11a(20 MHz) Channel 36 Normal link Inject interference signal Nosie floor (no short control) ac(80 MHz) Channel 42 Normal link Inject interference signal Nosie floor (no short control) 62/66

63 A.10 Receiver Blocking Test Data Note 1: The combination of the smallest channel bandwidth and the lowest data rate was reported. Note 2: Pmin = TX Level cable loss (7 dbm) Note 3:For conducted measurements, the levels of blocking signal have to be corrected by the actual antenna assembly gain. The actual maximum antenna gain is 2.99 dbi a: Operational channel (MHz) Pmin PER Limit dbm 8.8 % 10 % Blocking PER Result Type of Blocking signal signal power blocking Low High Limit Verdict frequency(mhz) (dbm) signal channel channel (see note 2) CW 0.00% 0.00% Pass The minimum performance CW 0.00% 0.00% Pass criterion shall be a PER less CW 0.00% 0.00% Pass than or equal to 10 % CW 0.00% 0.00% Pass Test Plot (Pmin) a Low channel 63/66