Distributed-feedback quantum cascade laser emitting at 3.2 μm

Size: px

Start display at page:

Download "Distributed-feedback quantum cascade laser emitting at 3.2 μm"

Chastity Barnett
6 years ago
Views:

1 Distributed-feedback quantum cascade laser emitting at 3.2 μm Johanna M. Wolf,, Alfredo Bismuto, 2 Mattias Beck and Jérôme Faist Institute for Quantum Electronics, ETH-Zurich, CH-893 Zurich, Switzerland 2 Alpes Lasers SA, CH-2 Neuchâtel, Switzerland wolfjo@phys.ethz.ch Abstract: In this work, we present GaInAs/AlAs/AlInAs quantum cascade lasers emitting from 3.2 to 3.4 μm. Single-mode emission is obtained using buried distributed-feedback gratings fabricated using standard deep-uv contact lithography. This technique can easily be transferred to industrial production. Devices with single-mode emission down to 3.9 μm were achieved with peak power of up to 25 mw at -2 C. A tuning range of cm was obtained by changing the device temperature between -3 C and 2 C. 24 Optical Society of America OCIS codes: (4.37) Infrared and far-infrared lasers; (4.596) Semiconductor lasers; (23.559) Quantum-well, -wire and -dot devices; (3.32) Integrated optics devices; (3.636) Spectroscopy, laser; (4.5965) Semiconductor lasers, quantum cascade. References and links. NIST, Nist chemistry webbook,. 2. C. S. Kim, M. Kim, J. Abell, W. W. Bewley, C. D. Merritt, C. L. Canedy, I. Vurgaftman, and J. R. Meyer, Midinfrared distributed-feedback interband cascade lasers with continuous-wave single-mode emission to 8 C, Appl. Phys. Lett., 64 (22). 3. G. Belenky, L. Shterengas, G. Kipshidze, and T. Hosoda, Type-I Diode Lasers for Spectral Region Above 3 μm, IEEE J. Sel. Topics Quantum Electron. 7, (2). 4. J. Faist, F. Capasso, D. L. Sivco, C. Sirtori, A. L. Hutchinson, and A. Y. Cho, Quantum Cascade Laser, Science 264, (994). 5. M. P. Semtsiv, M. Wienold, S. Dressler, and W. T. Masselink, Short-wavelength (λ 3.5μm) InP-based straincompensated quantum-cascade laser, Appl. Phys. Lett. 9, 5 (27). 6. A. Bismuto, S. Riedi, B. Hinkov, M. Beck, and J. Faist, Sb-free quantum cascade lasers in the 3 μm spectral range, Semicond. Sci. Technol. 27, 453 (22). 7. A. Bismuto, M. Beck, and J. Faist, High power Sb-free quantum cascade laser emitting at 3.3 μm above 35 K, Appl. Phys. Lett. 98, 94 (2). 8. N. Bandyopadhyay, Y. Bai, S. Tsao, S. Nida, S. Slivken, and M. Razeghi, Room temperature continuous wave operation of lambda μm quantum cascade lasers, Appl. Phys. Lett., 24 (22). 9. J. P. Commin, K. Kennedy, D. G. Revin, S. Y. Zhang, A. B. Krysa, and J. W. Cockburn, λ 3.36 μm room temperature InGaAs/AlAs(Sb) quantum cascade lasers with third order distributed feedback grating, Appl. Phys. Lett. 97, 3 (2).. E. Mujagić, C. Schwarzer, W. Schrenk, J. Chen, C. Gmachl, and G. Strasser, Ring-cavity surface-emitting lasers as a building block for tunable and coherent quantum cascade laser arrays, Semicond. Sci. Technol. 26, 49 (2).. S. Riedi, A. Hugi, A. Bismuto, M. Beck, and J. Faist, Broadband external cavity tuning in the 3-4 μm window, Appl. Phys. Lett. 3, 38 (23). 2. J. Jágerská, B. Tuzson, H. Looser, A. Bismuto, J. Faist, H. Prinz, and L. Emmenegger, Highly sensitive and fast detection of propane-butane using a 3 μm quantum cascade laser, Appl. Opt. 52, (23). (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 2

2 3. A. Bismuto, R. Terazzi, M. Beck, and J. Faist, Electrically tunable, high performance quantum cascade laser, Appl. Phys. Lett. 96, 45 (2). 4. W. Streifer, D. R.Scifres, and R. Burnham, Coupling Coefficients for Distributed Feedback Single- and Double- Heterostructure Diode Lasers, IEEE J. Quantum Electron., (975). 5. H. Haus and C. Shank, Antisymmetric taper of distributed feedback lasers, IEEE J. Quantum Electron. 2, (976). 6. A. Yariv and P. Yeh, Optical Waves in Crystals (John Wiley and Sons, 984).. Introduction The mid-infrared wavelength region is very important for gas sensing as many molecules have their vibrational-rotational modes there. For example, gases containing the methyl group, nitrous oxide, nitrogen dioxide, carbon dioxide, carbon monoxide and formaldehyde are all in the 3-5 μm spectral region []. Hydrocarbons like methane, ethane or formaldehyde could be measured with a high sensitivity (ppt) at this frequency range. This would enhance the possibilities for leak detection in industry, environmental monitoring and sensing for medical purposes. For many of these applications, a tunable single-mode emission at a previously determined wavelength is required. The mid-infrared spectral region can be covered with different types of lasers. Interband cascade lasers (ICL) have been presented with distributed feedback (DFB) emitters [2]. The grating, placed on top of the waveguide, was fabricated using e-beam lithography. Interband diode lasers achieved continuous-wave operation at 3.2 μm wavelength[3]. The devices mentioned above exploit interband emission, but the spectral range around 3 μm can be covered using intersubband transitions with a quantum cascade laser (QCL) [4] as well. Laser operation at 3.5 μm was shown at 8 K using different well materials for the upper and lower lasing state [5]. Emission down to 3.5 μm was reported [6, 7]. Lasers on a Sbfree material system showed watt-level emission at room-temperature. More recently, roomtemperature continuous-wave operation was reported at 3 and 3.2 μm [8]. Additionally, mode selection has been shown at 3.36 μm [9], where a third-order buried DFB grating was corrugated on top of a InGaAs/AlAs (Sb) QCL active region. Single-mode ring-csels based on quantum cascade structures were presented with a radial second-order grating at 8 μm []. Fabrication was done using e-beam lithography. The devices showed a low beam divergence (8 ). QCLs show good thermal qualities, output stabilities and tuning abilities. The GaInAs/AlAs/AlInAs material system on InP substrate is well-developed in terms of fabrication technologies. This is partially due to their widespread use in the telecommunication industry. Because of the extensive research, high quality growth of quantum wells is achieved today. A broad spectral coverage can be achieved with heterogeneous active regions, e.g. covering the spectral range from 3 to 4 μm []. Furthermore, applications for detecting propane and butane were demonstrated by EMPA using devices around 3.3 μm [2]. We present in this work QCL devices fabricated for output wavelength close to 3.3 μm. To achieve a better single-mode yield, a distributed feedback configuration with a first-order grating was chosen and realized by means of standard optical lithography. 2. Methods The QCL active region is a copy of the strain compensated structure published in 2 [7] on a GaInAs/AlAs/AlInAs material system. The thickness of the InGaAs layer on top of the active region, used for the DFB grating, was changed to 2 nm. The devices were fabricated as buried heterostructures [3] to improve thermal transport. The ridges were etched with width from 3 to 7 μm. The grating was done by partly etch- (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 22

The lasers were processed using standard buried heterostructure technique. The cleaved devices were mounted epilayer-up on copper blocks. Measurements were performed on a Peltier cooler.

3 ing the InGaAs layer. On the top of the etched grating, a n-doped cladding was deposited by MOVPE constituted by 3 μm of n-doped InP:Si (2 7 cm 3 ) followed by an 8 nm thick InGaAs:Si contact layer (6 8 cm 3 ). The lasers were processed using standard buried heterostructure technique. The cleaved devices were mounted epilayer-up on copper blocks. Measurements were performed on a Peltier cooler. The gratings were obtained by a single optical lithography (deep-uv light at 22 nm wavelength) and wet etching. They were designed for emission wavelengths between 3.2 and 3.45 μm and contain a quarter-wave shift placed in the center of each laser structure. Because of a mask fabrication resolution of about nm, we used only three different grating pitches, namely 5, 52 and 54 nm. In order to obtain a specific effective grating period, a combination of two grating pitches is used. For example, a 55 nm effective grating period could be obtained with 3 periods of a 5 nm grating followed by periods of a 52 nm grating. This combination is repeated on the photolithography mask. In the following we will refer to these composed gratings as dual-gratings and to the non-composed gratings as single-gratings. Fig.. SEM pictures. Left: A laser facet with a ridge width of 4.2 μm. Right: A cross section of the waveguide along the ridge direction. It shows the grating on top of the active region with an etching depth of 6 nm. The left part of Fig. is a SEM picture of the facet of a laser. It shows that the ridge cross section has a quasi-rectangular shape. On the right a SEM picture of a device cleaved along the waveguide is presented and displays the grating on top of the active region. The grating depth is 6 nm and the duty cycle is 25%. Compared to a 5% duty cycle, this leads to a reduced coupling constant of the optical mode towards the grating [4]. 3. Results The measured spontaneous emission of the active region is shown in Fig. 2 along with the measured laser spectra from several devices. Spontaneous emission data was taken at roomtemperature from a.6 mm long device. The device was measured perpendicular to the ridge with an applied voltage of 5.8 V. Laser spectra were measured under different driving conditions at C in pulsed operation. The spontaneous emission displays a full width half maximum of 62 cm, with a broad maxima from 3.5 to 3.34 μm. Laser emission ranged from 3.9 to 3.42 μm. In the bottom plot of Fig. 3 we show the stopband of one device. The device was measured below threshold with an applied voltage of 4.8 V at C. It exhibits a spectral width of Δk =6. cm at 37 cm with a quarter-wave shift mode in its center, as predicted by theory [5]. The device was lasing at 37 cm, on the edge of the stopband and at a higher-order mode at 3 cm. The dimensions of this device are 2.6 mm x 4 μm. The stopband width (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 23

4 corresponds to a coupling constant of κ = π n ef f Δk sin(π dc)=43 cm [4], where the effective refractive index n ef f is 3.2 and dc is the duty cycle of the grating. The coupling constant was not optimized for a value of κ*l around for the presented device lengths L, but adapted for losses of around cm obtained by transfer-matrix simulations. wavelength [μm] intensity (a.u.) wavenumber [cm ] Fig. 2. Room-temperature spontaneous emission of the active region(blue) showing a FWHM of 62 cm at 5.8 V. Additionally lasing spectra of some devices in pulsed operation under different driving conditions at C are presented. The supplementary stopbands aside from the one at 37 cm are due to higher-order lateral modes and due to the design of the grating. The presented example includes the periodicities 5 nm and 52 nm with a ratio of :3. This leads to a superperiod of L superperiod =2.6 μm. Therefore additional dual-grating modes of order n appear at wavenumbers of ±n 2 n ef f L superperiod = ±n 75.8 cm around the fundamental mode [6]. Transfermatrix simulations reproduced the stopbands including their quarter-wave shift modes. Not predicted are the higher order lateral modes which cannot be retrieved by the -D simulation (top plot of Fig. 3). A 2 mm long device was used in the simulations having the same grating design as the device presented. The separation to the higher-order dual-grating modes can be adjusted by changing L superperiod. In order to help distinguish the various mode types (dual-grating modes and higher-order lateral modes) the amplified spontaneous emission data of several devices was analysed. Fig. 4 illustrates the quarter-wave shift mode wavelengths versus grating periods. The 2nd order dual-grating mode has a lower coupling constant, and therefore, a narrower stopband. This is used for differentiating the st and 2nd order dual-grating mode. For the retrieval of the 2nd order lateral mode wavelengths, devices with only one grating period were analysed. In these cases the luminescence shows or 2 stopbands, which correspond to st and 2nd order lateral modes. With this analysis we group the data and approximate with linear fits using the formula for the Bragg wavelength: λ B = 2n i ef f ( Λ + j ) = 2n i ef f L Λ( + j ) superperiod N Λ (j-th dual-grating mode; i-th lateral mode) where Λ stands for the effective periodicity in the structure, N Λ for the length of the superperiod divided by Λ, i =, 2 for the first and second-order lateral mode respectively, j =, ± for the (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 24

5 transmission threshold in [cm ] wavenumber in [cm ] wavelength [μm] nd order dual grating mode 2 nd order st order lateral mode dual grating mode intensity (a.u.) nd order dual grating mode wavenumber [cm ] Fig. 3. Top: Transfer-matrix simulation of the transmission and threshold of a 2 mm long dual-grating DFB with aective periodicity of 55 nm and effective refractive index of Bottom: Measured amplified spontaneous emission of a 2.6 mm x 4 μm lasing device with the same dual-grating as the simulation. first and second-order dual-grating mode respectively. The black line in Fig. 4 is a linear fit for the fundamental dual-grating and the fundamental lateral modes. The 2nd order dual-grating modes are fitted by the light blue and dark blue lines while the 2nd order lateral modes are fitted by the red and green lines. The effective (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 25

6 wavelength [μm] =3.63 =3.65 = grating period Λ [nm] =3.22 =3.28 Fig. 4. Plot of the quarter-wave shift mode wavelengths versus grating period showing the fundamental mode (black), 2nd order dual-grating modes (light blue and dark blue) and 2nd order lateral modes (red, green). The purple crosses mark the lasing wavelengths. refractive index deduced from Fig. 4 is 3.65 for the fundamental lateral modes (fundamental and st order dual-grating modes) and 3.2 for the second-order lateral modes. Plotting the lasing frequencies versus the grating period (purple cross, Fig. 4), we deduce that almost all devices are lasing on the fundamental mode. Few devices are lasing on the 2nd order dualgrating mode or on a combination of the first and second-order lateral mode. For all measured devices we found a single mode yield of about 8%. We have not observed higher order lateral modes for ridge width narrower than 5 μm. Calculations of the optical mode intensity profile along the ridge, given by the transfer-matrix method, show periodic modulations of the mode. Fig. 5 shows the mode intensity profile of the fundamental and the two 2nd order dual-grating modes. The periodicity along the ridge amounts 2π to [6], where the imaginary part of the coupling constant κ and gain within the Δβ 2 κ2 structure is neglected and Δβ = 2 β 2 π Λ is the detuning of the propagation constant β from the Bragg frequency. In the case presented, the transfer-matrix simulation gave a periodicity of 2.6 μm, equal to the result for the formula above. Spacially modulated injection, with the same periodicity as the optical mode, could be used for generating tunable single mode emission. Fig. 6 and 7 show a device emitting around 3.29 μm with a side-mode suppression ratio of over 2 db. The ridge length is 2.64 mm and the width is 7 μm. The temperature tuning reached.5 cm from -2 to 3 C, giving a temperature tuning coefficient of.2 cm K. The threshold current density is 4.7 ka. A slope efficiency of 284 mw cm 2 A was measured at -2 C. The output power for the uncoated device per facet is 6 mw at -2 C whereas the highest output power we achieved was 25 mw on a multimode device. Based on the transfer-matrix computations of the losses, the lowest cavity loss should be achieved on the defect mode in the center of the stopband, whereas we observed our lasers to operate mostly on the band edge (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 26

7 intensity (a. u.) length [μm] Fig. 5. Simulation of the optical mode intensity along the ridge for a 42 μm long device made of periodicities of 5 nm and 52 nm with a superperiod of 2.6 μm and aective periodicity of 55 nm. Red: Data evaluated at λ = μm which corresponds to the fundamental quarter-wave shift mode. Blue and Green: Evaluation at λ = 3.83 μm and λ = μm which correspond to the 2nd order dual-grating mode. wavelength [μm] C 2 C C C C 2 C intensity (a.u.) wavenumber [cm ] Fig. 6. Spectra of an device emitting at 3.3 μm for various submount temperatures. (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 27

8 voltage [V] current density[ka/cm 2 ] C - C.5.5 current [A] C C 2 C 3 C 5 Fig. 7. Power-current-voltage characteristics of the device shown in Fig. 6. The slope efficiency is 284 mw ka A and the threshold current density is 4.7 at -2 cm C. 2 5 peak power per Facet [mw] mode. We attributed this to fabrication defects that affected most the modes that are highly confined in the center of the cavity. 4. Conclusion We demonstrated single-mode lasing from 3.9 to 3.4 μm and the quarter-wave shift mode in the spontaneous amplified emission. Temperature tuning of the single-mode emission is.2 cm K, and the output power is sufficient for most spectroscopic applications. Because of the relatively large thermal dissipation at threshold, continuous-wave operation has not yet been achieved. The results agree well with the coupled-mode theory and are reproduced by transfermatrix simulations. Additionally the predicted optical mode intensity profile along the ridge was presented. The incorporated DFB grating was accomplished with standard deep-uv optical lithography using only three grating periodicities. The spectral spacing towards the higher-order dual grating modes is proportional to L. Therefore lasing on the second-order grating superperiod modes could be avoided by using a shorter superperiod. We believe a reduction of defects will lead towards continuous-wave operation and lasing on the quarter-wave mode. Acknowledgments The authors would like to thank Martin Ebnöther and Emilio Gini for the MOVPE regrowth. Processing was done in FIRST Center for Micro- and Nanoscience. The research leading to these results has received funding from the European Union Seventh Framework Programme ( FP7/27-23 ) under grant agreement n 37884, the collaborative Integrated Project MIRIFISENS. (C) 24 OSA 27 January 24 Vol. 22, No. 2 DOI:.364/OE.22.2 OPTICS EXPRESS 28

Surface-Emitting Single-Mode Quantum Cascade Lasers

Surface-Emitting Single-Mode Quantum Cascade Lasers M. Austerer, C. Pflügl, W. Schrenk, S. Golka, G. Strasser Zentrum für Mikro- und Nanostrukturen, Technische Universität Wien, Floragasse 7, A-1040 Wien