Single-Channel: 6N135, 6N136, HCPL2503, HCPL4502 Dual-Channel: HCPL2530, HCPL2531 High Speed Transistor Optocouplers

Transcription

1 Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers Features High speed MBit/s Superior CMR 0kV/µs Dual-Channel / Double working voltage 40V RMS CTR guaranteed 0 70 C U.L. recognized (File # E90700) Applications Line receivers Pulse transformer replacement Output interface to CMOS-LSTTL-TTL Wide bandwidth analog coupling Schematics N/C + V F _ V CC V B N/C 4 5 GND,,, Pin 7 is not connected in Part Number + V F 3 V F GND / Description August 00 The,,,, and optocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector transistor. A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional phototransistor optocouplers by reducing the base-collector capacitance of the input transistor. An internal noise shield provides superior common mode rejection of 0kV/µs. An improved package allows superior insulation permitting a 40V working voltage compared to industry standard of 0V. Package Outlines,,,,, Rev V CC V 0 V 0 Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

2 Absolute Maximum Ratings (T A = 5 C unless otherwise specified) Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Condition Value Units T STG Storage Temperature -55 to +5 C T OPR Operating Temperature -55 to +00 C T SOL Lead Solder Temperature 60 for 0 sec C EMITTER I F (avg) I F (pk) I F (trans) V R P D DETECTOR I O (avg) DC/Average Forward Input 5 ma Current Each Channel () Peak Forward Input Current 50% duty cycle, ms P.W. 50 ma Each Channel () Peak Transient Input Current Each Channel Reverse Input Voltage Each Channel Input Power Dissipation Each Channel Average Output Current Each Channel Notes:. Derate linearly above 70 C free-air temperature at a rate of 0.mA/ C.. Derate linearly above 70 C free-air temperature at a rate of.6ma/ C. 3. Derate linearly above 70 C free-air temperature at a rate of 0.9 mw/ C. 4. Derate linearly above 70 C free-air temperature at a rate of.0 mw/ C. µs P.W., 300pps.0 A 5 V / and / mw HCPL-530/53 (3) 45 ma I O (pk) Peak Output Current Each 6 ma Channel V EBR Emitter-Base Reverse Voltage, and only 5 V V CC Supply Voltage -0.5 to 30 V Output Voltage -0.5 to 0 V I B Base Current, and only 5 ma PD Output Power Dissipation,,, (4) 00 mw Each Channel, 35 mw,,,,, Rev..0.7 Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

3 Electrical Characteristics (T A = 0 to 70 C Unless otherwise specified) Individual Component Characteristics Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit EMITTER V F Input Forward Voltage I F = 6mA, T A =5 C.45.7 V I F = 6mA. B VR Input Reverse Breakdown Voltage I R = 0 µa 5.0 V V F / T A DETECTOR Temperature Coefficient of Forward Voltage I OH Logic High Output Current I F = 0mA, = V CC = 5.5V, T A =5 C I F = 0mA, = V CC = 5V, T A =5 C I CCL Logic Low Supply Current I F = 6mA, = Open, V CC = 5V I F = I F = 6mA, = Open, V CC = 5V I CCH Logic High Supply Current I F = 0mA, = Open, V CC = 5V, T A =5 C *All Typicals at T A = 5 C I F = 6mA -.6 mv/ C All µa I F = 0mA, = V CC = 5V All 50 I F = 0mA, = Open, V CC = 5V I F = 0mA, = Open, V CC = 5V 0 00 µa µa,,,,, Rev Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

4 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Transfer Characteristics Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit COUPLED CTR L Current Transfer I F = 6mA, = 0.4 V, Ratio (5) V CC = 4.5V, T A =5 C Logic LOW Output Voltage *All Typicals at T A = 5 C I F = 6mA, V CC = 4.5V I F = 6mA, I O =.ma, V CC = 4.5V, T A =5 C I F = 6mA, I O = 3mA, V CC = 4.5V, T A =5 C I F = 6mA, I O = 0.mA, V CC = 4.5V I F = 6mA, I O =.4mA, V CC = 4.5V 7 50 % % 7 % L = 0.4V 5 % L = 0.5V L = 0.4V 5 30 % L = 0.5V L = 0.4V 9 30 % V Note: 5. Current Transfer Ratio is defined as a ratio of output collector current, I O, to the forward LED input current, I F, times 00%.,,,,, Rev Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

5 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Switching Characteristics (V CC = 5V) Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit T PHL T PLH CM H CM L Propagation Delay Time to Logic LOW Propagation Delay Time to Logic HIGH Common Mode Transient Immunity at Logic High Common Mode Transient Immunity at Logic Low T A = 5 C, R L = 4.kΩ, I F = 6mA (6) (Fig. 7) R L =.9kΩ, I F = 6mA, T A = 5 C (7) (Fig. 7) R L = 4.kΩ, I F = 6mA (6) (Fig. 7) R L =.9kΩ, I F = 6mA (7) (Fig. 7) T A = 5 C, (R L = 4.kΩ, I F = 6mA (6) (Fig. 7) R L =.9kΩ, I F = 6mA (7) (Fig. 7) T A = 5 C R L = 4.kΩ, I F = 6mA (6) (Fig. 7) R L =.9kΩ, I F = 6mA (7) (Fig. 7) I F = 0mA, V CM = 0V P-P, R L = 4.kΩ, T A = 5 C () (Fig. ) I F = 0mA, V CM = 0V P-P, R L =.9kΩ, T A = 5 C () (Fig. ) I F = 6mA, V CM = 0 V P-P, R L = 4.kΩ, T A = 5 C () (Fig. ) I F = 6mA, V CM = 0 V P-P, R L =.9kΩ () (Fig. ) µs µs.0 µs.0 µs µs µs.0 µs.0 µs 0,000 V/µs 0,000 V/µs 0,000 V/µs 0,000 V/µs ** All Typicals at T A = 5 C Notes: 6. The 4.kΩ load represents LSTTL unit load of 0.36mA and 6.kΩ pull-up resistor. 7. The.9kΩ load represents TTL unit load of.6ma and 5.6kΩ pull-up resistor.. Common mode transient immunity in logic high level is the maximum tolerable (positive) dv cm /dt on the leading edge of the common mode pulse signal V CM, to assure that the output will remain in a logic high state (i.e., >.0V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dv cm /dt on the trailing edge of the common mode pulse signal, V CM, to assure that the output will remain in a logic low state (i.e., < 0.V).,,,,, Rev Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

6 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Isolation Characteristics (T A = 0 to 70 C Unless otherwise specified) Symbol Characteristics Test Conditions Min Typ** Max Unit I I-O Input-Output Insulation Relative humidity = 45%,.0 µa Leakage Current T A = 5 C, t = 5s, V I-O = 3000 VDC (9) V ISO Withstand Insulation Test Voltage RH 50%, T A = 5 C, I I-O µa, 500 V RMS t = min. (9) R I-O Resistance (Input to Output) V I-O = 500VDC (9) 0 Ω C I-O Capacitance (Input to Output) f = MHz (9) 0.6 pf HFE DC Current Gain I O = 3mA, = 5V (9) 50 I I-I Input-Input Insulation Leakage RH 45%, V I-I = 500VDC (0) µa Current t = 5 s, (/53 only) R I-I Input-Input Resistance V I-I = 500 VDC (0) 0 Ω (/53 only) C I-I Input-Input Capacitance f = MHz) (0) (/53 only) 0.03 pf Notes: 9. Device is considered a two terminal device: Pins,, 3 and 4 are shorted together and Pins 5, 6, 7 and are shorted together. 0. Measured between pins and shorted together, and pins 3 and 4 shorted together.,,,,, Rev Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

7 I O OUTPUT CURRENT (ma) NORMALIZED CTR Tp PROPAGATION DELAY (ns) NORMALIZED CTR Typical Performance Curves Fig. Normalized CTR vs. Forward Current I F - FORWARD CURRENT (ma) Fig. 3 Output Current vs. Output Voltage T A = 5 C V CC = 5 V Normalized to: I F = 6 ma OUTPUT VOLTAGE (V) = 0.4 V V CC = 5 V T A = 5 C I F = 40mA I F = 35mA I F = 30mA I F = 5mA I F = 0mA I F = 5mA I F = 0mA I F = 5mA Fig. 5 Propagation Delay vs. Temperature R L =.9kΩ (TPHL) R = 4.kΩ (TPLH) L R L =.9kΩ (TPLH) R L = 4.kΩ (TPLH) T A TEMPERATURE ( C) I F = 6mA V CC = 5 V Fig. Normalized CTR vs. Temperature T A - TEMPERATURE ( C),,,,, Rev IOH LOGIC HIGH OUTPUT CURRENT (na) TP - PROPAGATION DELAY (ns) Normalized to: T A = 5 C I F = 6mA V CC = 5 V = 0.4 V Fig. 4 Logic High Output Current vs. Temperature I F = 0 ma V CC = 5 V = 5 V T A TEMPERATURE ( C) Fig. 6 Propagation Delay vs. Load Resistance IF - 0mA (TPHL) IF - 6mA (TPHL) IF - 6mA (TPLH) IF - 0mA (TPLH) V CC = 5 V T A = 5 C 0 R L LOAD RESISTANCE (kω) Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

8 Test Circuits V FF Pulse Generator I tr = 5ns F Z O= 50 Ω 0% D.C. I/f < 00µs I Monitor F B A I F R m + V F - + V F - Noise Shield 3 4 Noise Shield V CM Pulse Gen V CC V B VO 5 GND V CC V B V 6 O 5 GND R L 0. µf Test Circuit for,, HCPL-503 and HCPL- 450 R L 0. µf Test Circuit for,, HCPL-503 and HCPL V - V CM 0 V I F 0 T PHL t r,,,,, Rev V 0% 0% 0 V Switch at A : I = 0 ma F +5 V C L =.5 µf 90% Switch at A : I = 6 ma F Pulse Generator tr = 5ns Z O = 50 Ω 0% DUTY CYCLE I/f < 00µS IF IF MONITOR R m I F A B + VF VF + VF - - VF V TPLH Fig. 7 Switching Time Test Circuit V FF 90% 3 Noise Shield L 5 V L 5 V Noise Shield Fig. Common Mode Immunity Test Circuit V CM + - Pulse Gen VCC V0 V0 GND Test Circuit for HCPL-530 and HCPL-53 GND RL CC V RL V0 7 6 V0 Test Circuit for HCPL-530 and HCPL-53 t f 0. µf 0. µf +5 V C L =.5 µf +5 V Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

9 Ordering Information Option Example Part Number Description S S Surface Mount Lead Bend SD SD Surface Mount; Tape and reel W W 0.4" Lead Spacing V V VDE04 WV WV VDE04; 0.4 lead spacing SV SV VDE04; surface mount SDV SDV VDE04; surface mount; tape and reel Marking Information Definitions Fairchild logo Device number V VDE mark (Note: Only appears on parts ordered with VDE option See order entry table) 4 Two digit year code, e.g., 03 5 Two digit work week ranging from 0 to 53 6 Assembly package code,,,,, Rev XX YY 503 T 6 Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

10 Tape Specifications Reflow Profile 4.90 ± ± ± 0.05 User Direction of Feed 4.0 ± MAX 0.30 ± 0.0 Temperature ( C) ± ± 0. 5 C peak Ramp up = 3C/sec Time (Minute) 5 C, 0 30 s Time above 3C, sec Ø.55 ± ± 0.0 Peak reflow temperature: 5C (package surface temperature) Time of temperature higher than 3C for seconds One time soldering reflow is recommended.75 ± ± 0. Ø.6 ± ± 0.3,,,,, Rev Single-Channel:,,, Dual-Channel:, High Speed Transistor Optocouplers

11

12

13

14 TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks. AccuPower AttitudeEngine Awinda AX-CAP * BitSiC Build it Now CorePLUS CorePOWER CROSSVOLT CTL Current Transfer Logic DEUXPEED Dual Cool EcoSPARK EfficientMax ESBC Fairchild Fairchild Semiconductor FACT Quiet Series FACT FastvCore FETBench FPS F-PFS FRFET Global Power Resource SM GreenBridge Green FPS Green FPS e-series Gmax GTO IntelliMAX ISOPLANAR Making Small Speakers Sound Louder and Better MegaBuck MICROCOUPLER MicroFET MicroPak MicroPak MillerDrive MotionMax MotionGrid MTi MTx MVN mwsaver OptoHiT OPTOLOGIC OPTOPLANAR Power Supply WebDesigner PowerTrench PowerXS Programmable Active Droop QFET QS Quiet Series RapidConfigure Saving our world, mw/w/kw at a time SignalWise SmartMax SMART START Solutions for Your Success SPM STEALTH SuperFET SuperSOT -3 SuperSOT -6 SuperSOT - SupreMOS SyncFET Sync-Lock * TinyBoost TinyBuck TinyCalc TinyLogic TINYOPTO TinyPower TinyPWM TinyWire TranSiC TriFault Detect TRUECURRENT * SerDes UHC Ultra FRFET UniFET VCX VisualMax VoltagePlus XS Xsens 仙童 * Trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. TO OBTAIN THE LATEST, MOST UP-TO-DATE DATASHEET AND PRODUCT INFORMATION, VISIT OUR WEBSITE AT FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. AUTHORIZED USE Unless otherwise specified in this data sheet, this product is a standard commercial product and is not intended for use in applications that require extraordinary levels of quality and reliability. This product may not be used in the following applications, unless specifically approved in writing by a Fairchild officer: () automotive or other transportation, () military/aerospace, (3) any safety critical application including life critical medical equipment where the failure of the Fairchild product reasonably would be expected to result in personal injury, death or property damage. Customer s use of this product is subject to agreement of this Authorized Use policy. In the event of an unauthorized use of Fairchild s product, Fairchild accepts no liability in the event of product failure. In other respects, this product shall be subject to Fairchild s Worldwide Terms and Conditions of Sale, unless a separate agreement has been signed by both Parties. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, under Terms of Use Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Datasheet contains the design specifications for product development. Specifications may change Advance Information Formative / In Design in any manner without notice. Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Preliminary First Production Semiconductor reserves the right to make changes at any time without notice to improve design. Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make No Identification Needed Full Production changes at any time without notice to improve the design. Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. Obsolete Not In Production The datasheet is for reference information only. Rev. I77 Fairchild Semiconductor Corporation

15 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: SD WV V S SDV SDM