Single-Channel: 6N135, 6N136, HCPL2503, HCPL4502 Dual-Channel: HCPL2530, HCPL2531 High Speed Transistor Optocouplers

Transcription

1 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers Features High speed MBit/s Superior CMR 0kV/µs DualChannel / Double working voltage 40V RMS CTR guaranteed 0 70 C U.L. recognized (File # E90700) Applications Line receivers Pulse transformer replacement Output interface to CMOSLSTTLTTL Wide bandwidth analog coupling Schematics N/C + V F _ 3 7 V CC V B N/C 4 5 GND,,, Pin 7 is not connected in Part Number + V F 3 V F GND / Description August 00 The,,,, and optocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector transistor. A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional phototransistor optocouplers by reducing the basecollector capacitance of the input transistor. An internal noise shield provides superior common mode rejection of 0kV/µs. An improved package allows superior insulation permitting a 40V working voltage compared to industry standard of 0V. Package Outlines,,,,, Rev V CC V 0 V 0 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

2 Absolute Maximum Ratings (T A = 5 C unless otherwise specified) Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Condition Value Units T STG Storage Temperature 55 to +5 C T OPR Operating Temperature 55 to +00 C T SOL Lead Solder Temperature 0 for 0 sec C EMITTER I F (avg) I F (pk) I F (trans) V R P D DETECTOR I O (avg) DC/Average Forward Input 5 ma Current Each Channel () Peak Forward Input Current 50% duty cycle, ms P.W. 50 ma Each Channel () Peak Transient Input Current Each Channel Reverse Input Voltage Each Channel Input Power Dissipation Each Channel Average Output Current Each Channel Notes:. Derate linearly above 70 C freeair temperature at a rate of 0.mA/ C.. Derate linearly above 70 C freeair temperature at a rate of.ma/ C. 3. Derate linearly above 70 C freeair temperature at a rate of 0.9 mw/ C. 4. Derate linearly above 70 C freeair temperature at a rate of.0 mw/ C. µs P.W., 300pps.0 A 5 V / and / mw HCPL530/53 (3) 45 ma I O (pk) Peak Output Current Each ma Channel V EBR EmitterBase Reverse Voltage, and only 5 V V CC Supply Voltage 0.5 to 30 V Output Voltage 0.5 to 0 V I B Base Current, and only 5 ma PD Output Power Dissipation,,, (4) 00 mw Each Channel, 35 mw,,,,, Rev..0.7 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

3 Electrical Characteristics (T A = 0 to 70 C Unless otherwise specified) Individual Component Characteristics Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit EMITTER V F Input Forward Voltage I F = ma, T A =5 C.45.7 V I F = ma. B VR Input Reverse Breakdown Voltage I R = 0 µa 5.0 V V F / T A DETECTOR Temperature Coefficient of Forward Voltage I OH Logic High Output Current I F = 0mA, = V CC = 5.5V, T A =5 C I F = 0mA, = V CC = 5V, T A =5 C I CCL Logic Low Supply Current I F = ma, = Open, V CC = 5V I F = I F = ma, = Open, V CC = 5V I CCH Logic High Supply Current I F = 0mA, = Open, V CC = 5V, T A =5 C *All Typicals at T A = 5 C I F = ma. mv/ C All µa I F = 0mA, = V CC = 5V All 50 I F = 0mA, = Open, V CC = 5V I F = 0mA, = Open, V CC = 5V 0 00 µa µa,,,,, Rev SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

4 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Transfer Characteristics Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit COUPLED CTR L Current Transfer I F = ma, = 0.4 V, Ratio (5) V CC = 4.5V, T A =5 C Logic LOW Output Voltage *All Typicals at T A = 5 C I F = ma, V CC = 4.5V I F = ma, I O =.ma, V CC = 4.5V, T A =5 C I F = ma, I O = 3mA, V CC = 4.5V, T A =5 C I F = ma, I O = 0.mA, V CC = 4.5V I F = ma, I O =.4mA, V CC = 4.5V 7 50 % % 7 % L = 0.4V 5 % L = 0.5V L = 0.4V 5 30 % L = 0.5V L = 0.4V 9 30 % V Note: 5. Current Transfer Ratio is defined as a ratio of output collector current, I O, to the forward LED input current, I F, times 00%.,,,,, Rev SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

5 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Switching Characteristics (V CC = 5V) Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit T PHL T PLH CM H CM L Propagation Delay Time to Logic LOW Propagation Delay Time to Logic HIGH Common Mode Transient Immunity at Logic High Common Mode Transient Immunity at Logic Low T A = 5 C, R L = 4.kΩ, I F = ma () (Fig. 7) R L =.9kΩ, I F = ma, T A = 5 C (7) (Fig. 7) R L = 4.kΩ, I F = ma () (Fig. 7) R L =.9kΩ, I F = ma (7) (Fig. 7) T A = 5 C, (R L = 4.kΩ, I F = ma () (Fig. 7) R L =.9kΩ, I F = ma (7) (Fig. 7) T A = 5 C R L = 4.kΩ, I F = ma () (Fig. 7) R L =.9kΩ, I F = ma (7) (Fig. 7) I F = 0mA, V CM = 0V PP, R L = 4.kΩ, T A = 5 C () (Fig. ) I F = 0mA, V CM = 0V PP, R L =.9kΩ, T A = 5 C () (Fig. ) I F = ma, V CM = 0 V PP, R L = 4.kΩ, T A = 5 C () (Fig. ) I F = ma, V CM = 0 V PP, R L =.9kΩ () (Fig. ) µs µs.0 µs.0 µs µs µs.0 µs.0 µs 0,000 V/µs 0,000 V/µs 0,000 V/µs 0,000 V/µs ** All Typicals at T A = 5 C Notes:. The 4.kΩ load represents LSTTL unit load of 0.3mA and.kω pullup resistor. 7. The.9kΩ load represents TTL unit load of.ma and 5.kΩ pullup resistor.. Common mode transient immunity in logic high level is the maximum tolerable (positive) dv cm /dt on the leading edge of the common mode pulse signal V CM, to assure that the output will remain in a logic high state (i.e., >.0V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dv cm /dt on the trailing edge of the common mode pulse signal, V CM, to assure that the output will remain in a logic low state (i.e., < 0.V).,,,,, Rev SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

6 Electrical Characteristics (Continued) (T A = 0 to 70 C unless otherwise specified) Isolation Characteristics (T A = 0 to 70 C Unless otherwise specified) Symbol Characteristics Test Conditions Min Typ** Max Unit I IO InputOutput Insulation Relative humidity = 45%,.0 µa Leakage Current T A = 5 C, t = 5s, V IO = 3000 VDC (9) V ISO Withstand Insulation Test Voltage RH 50%, T A = 5 C, I IO µa, 500 V RMS t = min. (9) R IO Resistance (Input to Output) V IO = 500VDC (9) 0 Ω C IO Capacitance (Input to Output) f = MHz (9) 0. pf HFE DC Current Gain I O = 3mA, = 5V (9) 50 I II InputInput Insulation Leakage RH 45%, V II = 500VDC (0) µa Current t = 5 s, (/53 only) R II InputInput Resistance V II = 500 VDC (0) 0 Ω (/53 only) C II InputInput Capacitance f = MHz) (0) (/53 only) 0.03 pf Notes: 9. Device is considered a two terminal device: Pins,, 3 and 4 are shorted together and Pins 5,, 7 and are shorted together. 0. Measured between pins and shorted together, and pins 3 and 4 shorted together.,,,,, Rev..0.7 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

7 I O OUTPUT CURRENT (ma) NORMALIZED CTR Tp PROPAGATION DELAY (ns) NORMALIZED CTR Typical Performance Curves Fig. Normalized CTR vs. Forward Current I F FORWARD CURRENT (ma) Fig. 3 Output Current vs. Output Voltage T A = 5 C V CC = 5 V Normalized to: I F = ma OUTPUT VOLTAGE (V) = 0.4 V V CC = 5 V T A = 5 C I F = 40mA I F = 35mA I F = 30mA I F = 5mA I F = 0mA I F = 5mA I F = 0mA I F = 5mA Fig. 5 Propagation Delay vs. Temperature R L =.9kΩ (TPHL) R = 4.kΩ (TPLH) L R L =.9kΩ (TPLH) R L = 4.kΩ (TPLH) T A TEMPERATURE ( C) I F = ma V CC = 5 V Fig. Normalized CTR vs. Temperature T A TEMPERATURE ( C),,,,, Rev IOH LOGIC HIGH OUTPUT CURRENT (na) TP PROPAGATION DELAY (ns) Normalized to: T A = 5 C I F = ma V CC = 5 V = 0.4 V Fig. 4 Logic High Output Current vs. Temperature I F = 0 ma V CC = 5 V = 5 V T A TEMPERATURE ( C) Fig. Propagation Delay vs. Load Resistance IF 0mA (TPHL) IF ma (TPHL) IF ma (TPLH) IF 0mA (TPLH) V CC = 5 V T A = 5 C 0 R L LOAD RESISTANCE (kω) SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

8 Test Circuits V FF Pulse Generator I tr = 5ns F Z O= 50 Ω 0% D.C. I/f < 00µs I Monitor F B A I F R m + V F + V F Noise Shield 3 4 Noise Shield V CM Pulse Gen 7 7 V CC V B VO 5 GND V CC V B V O 5 GND R L 0. µf Test Circuit for,, HCPL503 and HCPL 450 R L 0. µf Test Circuit for,, HCPL503 and HCPL V V CM 0 V I F 0 T PHL t r,,,,, Rev V 0% 0% 0 V Switch at A : I = 0 ma F +5 V C L =.5 µf 90% Switch at A : I = ma F Pulse Generator tr = 5ns Z O = 50 Ω 0% DUTY CYCLE I/f < 00µS IF IF MONITOR R m I F A B + VF + VF + VF VF V TPLH Fig. 7 Switching Time Test Circuit V FF 90% 3 Noise Shield L 5 V L 5 V Noise Shield Fig. Common Mode Immunity Test Circuit V CM + Pulse Gen VCC V0 V0 GND Test Circuit for HCPL530 and HCPL53 GND RL CC V RL V0 7 V0 Test Circuit for HCPL530 and HCPL53 t f 0. µf 0. µf +5 V C L =.5 µf +5 V SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

9 Package Dimensions Through Hole SEATING PLANE 0.00 (5.0) 0.40 (3.55) 0.0 (0.5) 0.0 (0.4) Surface Mount (9.9) (9.40) (9.9) (9.40) (.54) TYP Lead Coplanarity : (0.0) MAX PIN ID (.) 0.50 (.35) (.7) (.4) 0.54 (3.90) 0.0 (3.05) PIN ID (.) 0.50 (.35) (.7) (.4) 0.0 (0.5) 0.0 (0.4) 0.00 (.54) TYP 0.00 (0.5) MIN 0.00 (0.5) MIN 0.0 (0.40) 0.00 (0.0) (7.) TYP (.4) 0.35 (.00) MIN (0.30) MAX. Note: All dimensions are in inches (millimeters) 5 MAX (7.) TYP 0.0 (0.4) 0.00 (0.0) 0.4" Lead Spacing 0.00 (5.0) 0.40 (3.55) 0.0 (0.5) 0.0 (0.4) (9.9) (9.40) 0.00 (.54) TYP Pin DIP Land Pattern 0.70 (.) 0.50 (.35) (.7) (.4) (0.0) MIN,,,,, Rev SEATING PLANE 0.45 (0.54) (7.49) PIN ID (3.90) 0.0 (3.05) 0.0 (0.40) 0.00 (0.0) 0.00 (.54) (.7) 0 to (0.) TYP 0.00 (.5) (0.7) SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

10 Ordering Information Option Example Part Number Description S S Surface Mount Lead Bend SD SD Surface Mount; Tape and reel W W 0.4" Lead Spacing V V VDE04 WV WV VDE04; 0.4 lead spacing SV SV VDE04; surface mount SDV SDV VDE04; surface mount; tape and reel Marking Information V Definitions Fairchild logo Device number 3 VDE mark (Note: Only appears on parts ordered with VDE option See order entry table) 4 Two digit year code, e.g., 03 5 Two digit work week ranging from 0 to 53 Assembly package code,,,,, Rev XX YY 503 T SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

11 Tape Specifications Reflow Profile 4.90 ± ± ± 0.05 User Direction of Feed 4.0 ± MAX 0.30 ± 0.0 Temperature ( C) ± ± 0. 5 C peak Ramp up = 3C/sec Time (Minute) 5 C, 0 30 s Time above 3C, 0 50 sec Peak reflow temperature: 5C (package surface temperature) Time of temperature higher than 3C for 0 50 seconds One time soldering reflow is recommended Ø.55 ± ± ± 0..0 ± ± 0.0 Ø. ± 0.,,,,, Rev..0.7 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

12 TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, andis not intended to be an exhaustive list of all such trademarks. Build it Now The Power Franchise CorePLUS CorePOWER CROSSVOLT TinyBoost CTL TinyBuck Current Transfer Logic EcoSPARK TinyLogic TINYOPTO EfficentMax TinyPower EZSWITCH * TinyPWM TinyWire µserdes Fairchild Fairchild Semiconductor FACT Quiet Series FACT FAST FastvCore FlashWriter * FPS FPFS FRFET Global Power Resource SM Green FPS Green FPS eseries GTO IntelliMAX ISOPLANAR MegaBuck MICROCOUPLER MicroFET MicroPak MillerDrive MotionMax MotionSPM OPTOLOGIC OPTOPLANAR PDP SPM PowerSPM PowerTrench Programmable Active Droop QFET QS Quiet Series RapidConfigure Saving our world, mw at a time SmartMax SMART START SPM STEALTH SuperFET SuperSOT 3 SuperSOT SuperSOT SupreMOS SyncFET *EZSWITCH and FlashWriter are trademarks of System General Corporation, used under license by Fairchild Semiconductor. UHC Ultra FRFET UniFET VCX VisualMax DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein:. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. ANTICOUNTERFEITING POLICY. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Fairchild Semiconductor Corporation's AntiCounterfeiting Policy. Fairchild's AntiCounterfeiting Policy is also stated on our external website, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of uptodate technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Preliminary No Identification Needed Obsolete Formative / In Design First Production Full Production Not In Production Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I35,,,,, Rev..0.7 SingleChannel:,,, DualChannel:, High Speed Transistor Optocouplers

13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: WV SD S V SDV