DETAIL PRODUCT SPECIFICATION CONTROL DRAWING Initial Release

Transcription

1 Revision DCO Description Revision Record Engineering Approval QA Approval Release - Initial Release EJ 7/19/07 TM 7/24/07 7/24/07 A Correction Table III, add Table IV. 1/7/08 B Change mfgr, para Update Table IV. 8/08/08 C D 5615 E 6879 Change mfgr to AC191 para , Table II maximum vcc, Table III freq range. Change document format/number. Update microcircuit usage. Update Table 1, code H. Add typical jitter to Table 3, Icc. Add EAR Destination Statement; corrected freq. breakpoints in and Table 2. CH RD Curtis Hooper Richard Duong 7/19/16 8/29/16 6/19/17 6/21/17 9/19/12 SD 8/17/16 8/29/16 Daniel Moline 6/27/17 6/29/17 This product and related technical data are subject to the EAR as promulgated and implemented by the U.S. Department of Commerce Bureau of Industry and Security. This product and related technical data are controlled under Export Control Classification Number (ECCN) 9A515.e.1 of the Commerce Control List (CCL), and may not be exported, re-exported, or retransferred outside of the U.S. or released or disclosed to Foreign Persons, as defined by the EAR, without first complying with all applicable U.S. Export Regulations. UNLESS OTHERWISE SPECIFIED Dimensions are in Inches Tolerances Decimal Fraction Angular.xxx ±.005.xx ±.02 x x 1 16 x ± 2.x ±.1 Proprietary Rights are involved in the subject matter of this material and all manufacturing, reproduction, use, and sales rights pertaining to such matter are expressly reserved. It is submitted in confidence for a specified purpose, and the recipient, by accepting this material, agrees that this material will not be used, copied, or reproduced in whole or in part, nor its contents revealed in any manner, or to any person, except for the purpose delivered. Prepared DETAIL PRODUCT SPECIFICATION CONTROL DRAWING Initial Release E. Jackson 7/19/07 Checked TITLE Basheer Remtulla 7/20/07 Engineering Approval E. Jackson 7/19/ West Jefferson Boulevard Culver City, CA USA HYBRID CRYSTAL OSCILLATOR, CLASS S, QT606L, DETAIL SPECIFICATION FOR Quality Assurance Approval DRAWING NO. REVISION T. Mitchell 7/24/07 QPDS-0120 E Released SCALE SIZE CAGE CODE PAGE T. Mitchell 7/24/07 NONE A of 6 F1195-1RB

2 1 PURPOSE 1.1 The purpose of this Detail (SCD) is to describe the specific quality and reliability requirements for hybrid, hermetically sealed, crystal oscillators for use in space flight missions. 2 SCOPE 2.1 This specification establishes the minimum detail requirements for QT606L intended for use in conjunction with the applicable general SCD. 3 PART PROTECTION AND SAFETY 3.1 These items are susceptible to breakdown damage resulting from electrostatic discharge. Every precaution shall be taken while handling, installing, and testing the parts to prevent static charge. Care should be exercised to not apply more than rated voltage or current to any terminal/pad during testing. 4 PART NUMBER 4.1 The Q-Tech Part Number shall be as specified in Table 1 herein. 5 APPLICABLE DOCUMENTATION & REFERENCES 5.1 The following documents form a part of this drawing to the extent specified or modified herein. 5.2 Q-Tech , Hybrid Crystal Oscillators, Class S, General Specification for 5.3 Application of Documents Issue of Documents Document revisions in effect on the date of the customer purchase order form a part of this drawing except as modified herein Order of Precedence In the event of conflict between this document and the references cited herein or other requirements, the precedence in which requirements shall govern, in descending order, is as follows: a) Applicable Customer Purchase Order b) Applicable Detail SCD/Drawing c) Applicable General SCD d) Other Specifications, Standards, and Documentation Referenced Above Customer Purchase Order Special Requirements Additional special requirements shall be specified in the applicable customer purchase order when additional requirements or modifications are needed for compliance to special programs or product line compliance. Unique identification of the items produced may be required General Any reference to the general specification or general SCD refers to the General cited in the Applicable Documentation and References section, unless otherwise specified. A QPDS-0120 E 2 of 6

3 6 GENERAL REQUIREMENTS 6.1 Definition of Requirements Items supplied to this detail SCD shall meet the detail requirements specified herein. 6.2 Individual Item Requirements The individual item requirements shall be in accordance with General SCD with the exceptions, modifications, and additions herein. 6.3 Approved Source of Supply Hybrid crystal oscillators shall be supplied from the manufacturer specified in Source of Supply below. 6.4 Design and Construction Outline Dimensions and Terminal Connections The outline dimensions and terminal connections shall be as shown in Figure 1 herein Package Body and Lead Finish The package body and lead finish shall be gold in accordance with MIL-PRF Active Devices The microcircuit used in this part shall use CMOS technology and shall be from a wafer proven to be radiation tolerant to 100 KRad (Si) total ionizing dose CMOS Microcircuit Usage For frequencies below 3.75 MHz, the CMOS output microcircuit shall be 54AC191, see DSCC SMD For frequencies from 3.75 MHz but below 15MHz, the CMOS output microcircuit shall be 54AC74, see DSCC SMD For frequencies greater than or equal to 15 MHz, the CMOS microcircuit shall be 54AC00, see DSCC SMD These microcircuits are specified to be single event latchup free for LET up to 93 MeV-cm 2 /mg. For output frequencies up to 70 MHz, the manufacturer shall be ST Microelectronics Corporation. For output frequencies greater than 70 MHz, the manufacturer shall be National Semiconductor Corporation. 6.5 Performance Requirements Maximum Ratings The maximum ratings shall be as specified in Table 2 herein Electrical Performance Characteristics and Limits The electrical performance requirements and limits shall be in accordance with Table 3 herein Delta Limits Except for frequency aging (refer to Table 3 herein), delta limits shall be in accordance with the general SCD Total Dose Radiation Limits Hybrid crystal oscillators supplied in accordance with this detail SCD shall be capable of meeting the performance requirements after being exposed to 100 KRad (Si) total dose radiation levels. 7 QUALITY ASSURANCE PROVISIONS 7.1 General The quality assurance provisions shall be in accordance with the general SCD with the exceptions, modifications, and additions specified herein. 7.2 Screening The screening tests shall be in accordance with the general SCD. A QPDS-0120 E 3 of 6

4 7.3 Quality Conformance Inspection (QCI) Quality Conformance Inspection shall be in accordance with the general SCD and shall be required only when specified by the purchase order. 8 PREPARATION FOR DELIVERY 8.1 Preservation, Packaging, and Packing Hybrid crystal oscillators shall be prepared for delivery in accordance with the general SCD. 8.2 Electrostatic Discharge Sensitivity The devices supplied to this detail SCD shall be considered to be electrostatic discharge sensitive and require further protection and shall use the packaging requirements class 1C in accordance with par of MIL- PRF SOURCE OF SUPPLY 9.1 Approved Manufacturer West Jefferson Boulevard Culver City, CA USA 10 NOTES 10.1 The notes of the general SCD are applicable to this drawing Ordering Information The procuring activity shall advise at the time of Request for Quotation if quality conformance inspection is to be required. Table 1 Part Number Model Number Supply Voltage Temperature Stability Screening Frequency (MHz) QT606 L: 3.3 A: ±65 PPM, -55 C to +125 C E: Engineering Model B: ±50 PPM, -55 C to +125 C M: Flight Model to C: ±50 PPM, -55 C to +105 C D: ±40 PPM, -55 C to +105 C E: ±30 PPM, -40 C to +85 C F: ± 50 PPM, -20 C to +70 C G: ±25 PPM, -20 C to +70 C * H: ±5 PPM, 0 C to +55 C * Frequency/Temperature stability (tolerance) shall be referenced to the specified nominal output frequency, except for temp code H, in which case it is referenced to room temperature (T = 25 ± 2 C). For temp code H, room temperature tolerance shall be ± 15 PPM. Part Number Examples QT606LBM MHz would be a Flight Model QT606, CMOS, 3.3 volts, stability ±50 PPM over -55 C to MHz output. QT606LEE MHz would be an Engineering Model QT606, CMOS, 3.3 volts, stability ±30 PPM over -40 C to MHz output. A QPDS-0120 E 4 of 6

5 Table 2 Maximum Ratings Parameter Symbol Minimum Maximum Units Supply Voltage VCC 0 7 Volts Operating Temperature TC C Storage Temperature TSTG C Lead Solder Temperature/Time +250/10 C/Seconds Package Thermal Resistance Θjc 50 C/W Electrical Parameter Table 3 Electrical Performance Characteristics Test Conditions (Note 2 and 3) Limits Min. Nom. Max. Units Frequency Range MHz Frequency/Temperature Stability See Table 1 Note 1, 4 Supply Voltage Vdc Input Current Measured without load at 3.63 Vdc Output Frequency: Below 60 MHz 15 ma 60 MHz 100 MHz 20 ma Load CMOS Note 6 Output Voltage Logic 0 Vcc x 0.1 Vdc Output Voltage Logic 1 Vcc x 0.9 Vdc Output Waveform Squarewave N/A Rise / Fall Time Output Frequency: Notes Up to 70 MHz 5 nsec Note 7 > 70 MHz 3 nsec Note 7 Duty Cycle % Frequency Aging (After 30 Days) 70 C ± 3 C ±1.5 ppm Frequency Aging (After 1 Year) 70 C ± 3 C ±10 ppm Start Up Time 10 msec Jitter (cycle-to-cycle, rms) Output Frequency: Less than 3.75 MHz 40 ps Note MHz 100MHz 10 ps Note 8 NOTES 1. The limit for Frequency Stability (tolerance) is referenced to the specified nominal output frequency, except for temp code H as noted above. 2. Unless otherwise specified, the limits are over the full operating temperature range, and under specified load conditions and nominal Supply Voltage. 3. Unless otherwise specified, all measurements are in accordance with MIL-PRF Up to 30 days after shipment. 5. Voltage values are with respect to network ground terminal. 6. A standard CMOS load of 10 KΩ 15 pf shall be used. See MIL-PRF-55310/26 for CMOS waveform measurement definitions. 7. Measured between 10% Vdc and 90% Vdc. 8. Guaranteed by design, not tested. A QPDS-0120 E 5 of 6

6 Figure 1 Package Dimensions and Terminal Connections Table 4 Terminal Connections Terminal No. Connection Terminal No. Connection 1 N/C 8 OUTPUT 2 N/C 9 N/C 3 N/C 10 N/C 4 N/C 11 N/C 5 N/C 12 N/C 6 N/C 13 N/C 7 GROUND/CASE 14 Vcc NOTES 1. Dimensions are in inches. 2. Lead numbers are for reference only and are not marked on the unit. 3. A triangle symbol is marked on the corner of the package to indicate Pin 1. A QPDS-0120 E 6 of 6