Trunking ZH with performances specific to fire: Low-Fire Hazard

Transcription

1 87045 LIMOGES Cedex Phone : Fax : Trunking ZH with performances CONTENTS PAGES 1.Trunking 1 to 2 2.Finishing accessories 3 to 8 3.Supports 9 4.Technical characteristics 10 5.Material characteristics TRUNKING. Context: To answer well the key objective of safety in the event of fire is a complex question because the security level is influenced by many factors: - the choice of the various electric/electronic products installed but also quantities installed. - the site where these products are installed: the dimension of the room, its ventilation, its use to accommodate many people or to place materials of value or to store flammable materials, the facility for an occupant to evacuate this site or for the first-aid organizations to reach it - the nature and quantity of the no electric products in the vicinity. - the existence or not of average automatics of fire control Traditionally, the safety of the people is the priority. The products of cable managment must be not propagators of the flame to avoid the propagation of the fire and thus to facilitate the evacuation by the occupants: - Standard of installation NF C (article 421.7): The conduits, trunkings posed into apparent and the cable shelves must satisfy the characteristics with non-propagation with the flame. - Its handy guide UTE C Drains - Modes of installation - Connections (article Behavior in fire): 1. TRUNKING (cont.) Benefit: Legrand proposes an offer of products with performances specific to fire which facilitate the evacuation of the buildings by the occupants and the intervention of the first-aid organizations: in the event of fire smoke is less opaque and less acid. In the event of fire, the time of evacuation is a decisive criterion: - The reduction of opacity increases the visibility of the ways of evacuation by the occupants and of the access paths by the first-aid organizations. - The reduction of acidity decreases the irritating effects of smoke which harms the sight and breathing. Applications: These offers can find their application in the places with requirements specific to fire: - Establishments Receiving of Public (ERP): Hospital, Old people's homes, Hotels, Schools, Museums, Shopping malls, Cinemas, Administrative buildings - Establishments sheltering of the equipment of value: Computer rooms, Cal center - Stations, Airports, Subway, Tunnels - Industries When the drains in buried installation or are not drowned in fireproof materials such as plaster, concrete, equivalent material, they must satisfy the characteristics with not-propagation with the flame defined in the standards in force. In apparent assembly, the systems of conduits, trunkings, conduitsections, the cable shelves must satisfy the test with notpropagation with the flame. For specific applications, the prescriber can take into account additional characteristics. 1 / 10

2 1. TRUNKING (cont.) 1.1. Mini-trunking ZH 1. TRUNKING (cont.) 1.2. Trunking ZH Mini-trunkings x25 100m x40 60m x60 24m Range : Mini-trunking 25x25 ref Trunkings x85 24m x130 12m x100 16m x190 12m Range : 50x85 (1 compartment) ref x100 (1 compartment) ref Mini-trunking 25x40 ref x130 (1 compartment) ref x190 (2 compartments) ref Mini-trunking 40x60 ref Delivered in length of 2m with cover White Color Fixing by: - wall plugs for immediate fixing - glue - screw, nails Cut out using a saw (standard hacksaw) For an installation of the mini-trunking sections fixed at the wall and supported by the ground: The mini-trunking must be installed with 15mm mini of the ground following EN Delivered in length of 2m with cover White Color Fixing by: - wall plugs for immediate fixing - glue - screw, nails Cut out using a saw (standard hacksaw) 1.3. Partition ZH ref Delivered in length of 2m White Color Allows separation of various types of current (high, low and data) Snap on T which are inside the body of the trunking aging : 72 m 2 / 10

3 2. FINISHING ACCESSORIES Internal angle ref /11 et for mini-trunkings 2.2. Internal angle ref /33/35 for trunkings The junction in interior angle of two pieces of the same section: - the cut of miter avoids on the trunking - aesthetics improves Variable internal angles of 85 with 95. Internal angle x x x60 5 The junction in interior angle of two pieces of the same section: - the cut of miter avoids on the trunking - aesthetics improves The internal angles are delivered with 2 elements Variable internal angles of 80 with 120. Positioning of the mini-trunking to the wall before clipsage of the internal angle Positioning of the trunking to the wall before clipsage of the internal angle Internal angle x x x x190 5 For information, use of the trunking 85x50, clic the adaptor (delivered with) on the two sides inside the angle: 3 / 10

4 2.3. External angle ref /12 et for mini-trunkings 2.4 External angle ref /23/25 for trunkings The junction in exterior angle of two pieces of the same section: - avoid the cut of miter on the trunking - aesthetics improves Variable external angles of 85 with 95. The junction in interior angle of two pieces of the same section: - avoid the cut of miter on the trunking - aesthetics improves The external angles are delivered with 2 elements Variable internal angles of 60 with 120. External angle x x x60 5 Positioning of the mini-trunking to the wall before clipsage of the external angle Positioning of the trunking to the wall before clipsage of the external angle External angle x x x x190 5 For information, use of the trunking 85x50, clic the adaptor (delivered with) on the two sides inside the angle: 4 / 10

5 2.5. Flat angle ref /13 et for mini-trunkings 2.6 Flat angle ref /13/15 for trunkings The junction in flat angle of two same sections allows: - the cut of miter avoids on the trunking - aesthetics (covering of the cut) improves Angles not variable (fixes at 90 ) The flat angles are delivered with 1 element. The junction in flat angle of two same sections allows: - the cut of miter avoids on the trunking - aesthetics (covering of the cut) improves Angles not variable (fixes at 90 ) The flat angles are delivered with 2 elements. Flat angle x x x60 5 Positioning of the mini-trunking to the wall before clipsage of the flat angle Positioning of the trunking to the wall before clipsage of the flat angle Flat angle x x x x / 10

6 2.7. End cap ref /14 et for mini-trunkings 2.8. End cap ref /43/45 for trunkings Assembly on the body by the front or by the side Allows to block the end of the body: - improvement of aesthetics (covering of the cut) - left or right end cap Assembly on the body by fitment and screwing. The end cap is not delivered with a screw. Allows to block the end of the body: - improvement of aesthetics (covering of the cut) - left or right end cap Assembly on the body by fitment and screwing. The end cap is delivered with a screw. End cap x x x60 10 Screwing on the trunking Screwing in the exterior End cap x x x x / 10

7 2.9. Flat junction ref /16 et for mini-trunkings 2.10 Cover joint ref for trunkings The junction in T allows. - aesthetics (covering of the cut) improves Assembly on the body by clipsage Flat junction x x x60 5 Allows: - the junction end to end of two covers 80mm - to improve aesthetics (covering of the cut) Assembly of the joint by clipsage Assembly of the cover joint with cover The cover joint slips and positions on the end of a lid, the other side remains available for reopening Cover joint Couvercle / 10

8 2.11. Cover/body joint ref /15 et for mini-trunkings 2.12 Body joint ref /53/55 for trunkings Assembly of the joint by clipsage on the bottom of the mini-trunking and joining with glue on 1 only cover (not provided glue) Allows: - the junction end to end of two mini-trunkings - to improve aesthetics (covering of the cut) Assembly of the mini-trunking by clipsage Allows: - the junction end to end of two same section - to improve aesthetics (covering of the cut) - the alignment of the bodies under installation Body joint delivered with platinum and junction of partition if need be Cover/body joint x x x60 10 Body joint x x x x / 10

9 3. SUPPORTS 3.1 Supports for Mosaic ref 3. SUPPORTS (cont.) 3.2 Universal supports ref /89 Ref modules = 10 - Universal support 60 réf Assembly on trunking equipped with cover 80mm with any 60mm fixing centres wiring accesories. Ref modules = 5 Dimensions of supports : Ref modules = 5 Grey color aging : 5 Snap-on supports and possible to put them next to each other, delivered with cover plate. - Back box réf Assembly on trunking equipped with cover 80mm with equipment Mosaic for trunking of 2/4/6 modules. Dimensions of supports : 58mm Cover plate 73mm 78mm support 65mm 2 mod mod mod Support (mm) 58x73 123x73 168x73 Cover plate (mm) 65x78 130x78 175x78 Grey color aging : 5 Allows to isolate equipment while clipsant itself with the back from the framework of fixing equipment distance between centres 60 ref / 10

10 4. TECHNICAL CHARACTERISTICS Wiring capacity: Dimensions Cross section Diamètre maxi 3x1.5mm² 3x2.5mm² UTP & FTP CAT.6 Maxi 25x x x x x x x190(2 compart) 4017/ /40 45/45 29/29 164/164 Capacity with Mosaic support: Dimensions Cross section Diamètre maxi 3x1.5mm² 3x2.5mm² UTP & FTP CAT.6 Maxi 50x x x x190(2 compart) 2037/ /15 22/22 15/15 83/83 Classification for trunking with performances specific to fire (standard EN ) 6.2 Resistance to impact for installation and application 2.0J 6.3 Minimum storage and transport temperature - 25 C 6.3 Minimum installation and application temperature + 15 C 6.3 Maximum application temperature + 60 C 6.4 Resistance to flame propagation Non-flame propagating 6.5 Electrical continuity characteristic Without electrical continuity characteristic 6.6 Electrical insulating characteristic With electrical insulating characteristic 6.7 Degrees of protection provided by enclosure IP 3XD or IP40 please look on the board outside 6.9 The system access cover retention With a tool The position when surface mounted Wall fixed The functions provided Type 1 or 2 please look on the board outside Rated current 500 V Against mechanical shocks IK 07 Compositions and fonctions for trunking with performances specific to fire. Body Dimension Trunking AI (1) AE (1) AP (1) End cap Joint Cover Joint x x x Té Type and IP 2 / IP30- D 2 / IP30- D 2 / IP30- D x / IP x / IP x / IP x190(2c) / IP40 (1) Classification and the performances are declared for an assembly with 90 For your information, (2c) = 2 compartments Attention with use of conductors inside the sections Inside the mini-trunkings, connection of the conductors using domino to respect the IP 20 mini. 5. MATERIAL CHARACTERISTICS. Trunking and partition => PC ABS, conform to the Directive RoHS* Accessories => ABS conform to the Directive RoHS* *RoHS designation : Restriction of the use of certain Hazardous Susbtances, RoHS in the Equipements Electriques and Electroniques (EEE) 10 / 10