Switch Mode Power Supply SMPS-T160. Data sheet LINAK.COM/TECHLINE

Transcription

1 Switch Mode Power Supply SMPS-T160 Data sheet LINAK.COM/TECHLINE

2 SMPS-T160 The SMPS-T160 is a powerful Switch Mode Power Supply typically used for outdoor applications within the TECHLINE segment. SMPS-T160 is an eco-friendly solution due to a low standby power consumption compared to traditional transformer solutions. The universal input voltage makes the SMPS adaptable to the worldwide market irrespective of the input voltage. This TECHLINE actuator comes with IC - Integrated controller. For more information on our IC options, please see: Features and Options: Nominal input voltage (mains voltage): 100 V AC V AC +10 / -15%, Universal input voltage Nominal input frequency: 50 Hz / 60 Hz Typical standby power consumption: Approx. 0.1 W Nominal output voltage: 29 VDC Housing colour: Dark Olivish Grey Protection class: IP66 Brackets for e.g. application or wall mounting Mains cable connector for: UL, Japan/CH (Swiss), Australia, UK, EU LINAK.COM/TECHLINE Usage: Compatibility: LA12 TM, LA14 IC TM, LA23 TM, LA25 IC TM and LA35 TM, only 24 V DC Duty Cycle: 10%, 2 minutes continuous use followed by 18 minutes not in use Operating temperature: -20 C to 40 C Storage temperature: -40 C to 70 C Relative humidity: 20% to 30 C not condensing Atmospheric pressure: 700 to 1060 hpa Altitude: max metres above sea level In order to extend/retract the actuator, a voltage greater than 21 VDC must be applied to red/black wire. In order to stop extending/retracting the actuator, a voltage less than 9 V DC must be applied to red/black wire (normally 0 V DC) Approvals: The SMPS-T160 is approved according to the following standards: /108/EC, EMC Directive /95/EC, Low Voltage Directive - EMC Standards: EN :2006+A1:2009+A2:2011 EN :1997+A1:2001+A2:2008 EN :2006+A1:2009+A2:2009 EN : Safety Standards: EN :2005+A1:2009 EN :2009+A1:2013 Page 2 of 12

3 Contents Output... 3 SMPS-T160 dimensions... 4 System example... 5 I/O Specifications: SMPS with standard output interface...6 System combination possibilities...7 Page 3 of 12

4 Output Nominal output voltage 29 V DC ±10% (V IN ) Ripple 500 mvp-p Total Output current 5.5A at a duty cycle of 10% Please be aware if connecting an external control to an SMPS configured with an output interface: Hand control. The unit connected should be capable of tolerating overvoltage, caused by soft stop ping actuators. Overvoltage caused by soft stopping actuators can reach up to 38 V. Furthermore, please be aware that the supply to control units are limited to 300 ma each. Page 4 of 12

5 SMPS-T160 Dimensions Without brackets: 249 Drawing No.: SMPS-T160_LONG_BRACKETS With short brackets: ( ) 261 ( 35 ) 4.5 Page 5 of 12

6 With long brackets: 249 ( ) ( 67.6 ) 78 System example Page 6 of 12

7 I/O Specifications: SMPS with standard output interface: Input/Output Specification Comments Description The actuator is powered by the SMPS and the signals are transferred to a signal cable if attached to the SMPS Signal Power + Signal signal SMPS-T160 Red Extends the actuator On/off voltages: Black Retracts the actuator AC Supply > 67% of 29 V DC (VIN) = ON < 33% of 29 V DC (VIN) = OFF Input current: 10 ma Green Yellow Endstop signal out Endstop signal in Output voltage min. 29 V DC (V IN ) - 1V Source current max. 100mA Endstop signals are NOT potential free. For further information, see the relevant I/O specifications scheme in the actuator s user manual Violet Analogue feedback (Hall Pot): Configure any high/low combination between 0-10V Single Hall output (PNP) Digital output feedback PWM: Configure any high/low combination between 0-100% Analogue feedback (4-20mA): Configure any high/low combination between 4-20mA All absolute value feedbacks (Hall Pot, PWM and 4-20 ma) AC supply For further information, see the relevant I/O specification s scheme in the actuator s user manual White Signal GND For further information, see the relevant I/O specification s scheme in the actuator s user manual Page 7 of 12

8 System combination possibilities SMPS-T160 LA12 IC TM LA14 IC TM LA23 IC TM LA25 IC TM LA35 IC TM Bluetooth receiver RF receiver HB40 DP Signal cable System combination possibilities - LA35 IC TM LA35 IC TM SMPS-T160 Signal cable Copyright LINAK MA M C. Chapter Terms of use The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and up-to-date information on its products. However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products. While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK. All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK. Page 8 of 12 FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER S MANUALS