AD7520, AD Bit, 12-Bit, Multiplying D/A Converters. Features. Ordering Information. Pinouts. Data Sheet August 2002 FN3104.

Size: px
Start display at page:

Download "AD7520, AD Bit, 12-Bit, Multiplying D/A Converters. Features. Ordering Information. Pinouts. Data Sheet August 2002 FN3104."

Transcription

1 AD720, AD72 Data Sheet August 2002 FN Bit, 2Bit, Multiplying D/A Converters The AD720 and AD72 are monolithic, high accuracy, low cost 0bit and 2bit resolution, multiplying digitaltoanalog converters (DAC). Intersil s thinfilm on CMOS processing gives up to 0bit accuracy with TTL/CMOS compatible operation. Digital inputs are fully protected against static discharge by diodes to ground and positive supply. Typical applications include digital/analog interfacing, multiplication and division, programmable power supplies, CRT character generation, digitally controlled gain circuits, integrators and attenuators, etc. Features AD720, 0Bit Resolution; 8Bit Linearity AD72, 2Bit Resolution; 0Bit Linearity Low Power Dissipation (Max) mW Low Nonlinearity Tempco at 2ppm of FSR/ o C Current Settling Time to 0.0% of FSR µs Supply Voltage Range ±V to +V TTL/CMOS Compatible Full Input Static Protection Ordering Information PART NUMBER LINEARITY (INL, DNL) TEMP. RANGE ( o C) PACKAGE PKG. NO. AD720JN 0.2% (8Bit) 0 to 70 Ld PDIP E.3 AD72LN 0.0% (0 Bit) 0 to 70 8 Ld PDIP E8.3 Pinouts AD720 (PDIP) TOP VIEW AD72 (PDIP) TOP VIEW BIT BIT 2 BIT 3 BIT 4 BIT V+ (LSB) BIT 9 BIT 8 BIT 7 BIT BIT BIT 2 BIT 3 BIT 4 BIT BIT V+ BIT 2 (LSB) BIT BIT 9 BIT 8 BIT 7 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 888INTERSIL or Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc All Rights Reserved

2 AD720, AD72 Absolute Maximum Ratings Supply Voltage (V+ to ) V ±2V Digital Input Voltage Range V+ to Output Voltage Compliance mV to V+ Operating Conditions Temperature Ranges JN, LN Versions o C to 70 o C Thermal Information Thermal Resistance (Typical, Note ) θ JA ( o C/W) θ JC ( o C/W) Ld PDIP Package 90 N/A 8 Ld PDIP Package 80 N/A Maximum Junction Temperature (Plastic Packages) o C Maximum Storage Temperature Range o C to 0 o C Maximum Lead Temperature (Soldering 0s) o C CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. The digital control inputs are zener protected; however, permanent damage may occur on unconnected units under high energy electrostatic fields. Keep unused units in conductive foam at all times. Do not apply voltages higher than V DD or less than potential on any terminal except and.. θ JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications V+ = +V, = +0V, T A = 2 o C Unless Otherwise Specified AD720 AD72 PARAMETER TEST CONDITIONS MIN TYP MAX MIN TYP MAX UNITS SYSTEM PERFORMANCE (Note 2) Resolution Bits Nonlinearity J (Note 3) (Figure 2) 0V +0V L 0V +0V (Figure 2) Nonlinearity Tempco 0V +0V (Notes 3, 4) ±0.2 (8Bit) ±0.0 (0Bit) % of FSR ±0.0 (0Bit) % of FSR ±2 ±2 ppm of FSR/ o C Gain Error ±0.3 ±0.3 % of FSR Gain Error Tempco ±0 ±0 ppm of FSR/ o C Output Leakage Current (Either Output) DYNAMIC CHARACTERISTICS Output Current Settling Time Feedthrough Error REFERENCE INPUT Input Resistance Over the Specified Temperature Range To 0.0% of FSR (All Digital Inputs Low To High And High To Low) (Note 4) (Figure 7) = 20V PP, 00kHz All Digital Inputs Low (Note 4) (Figure ) All Digital Inputs High at Ground ±200 ±200 na.0.0 µs 0 0 mv PP kω ANALOG OUTPUT Output Capacitance All Digital Inputs High pf (Note 4) (Figure ) 7 7 pf All Digital Inputs Low 7 7 pf (Note 4) (Figure ) pf Output Noise Both Outputs (Note 4) (Figure 4) Equivalent to 0kΩ Equivalent to 0kΩ Johnson Noise DIGITAL INPUTS Low State Threshold, V IL Over the Specified V High State Threshold, V Temperature Range IH V V IN = 0V or +V Input Current, I IL, I IH ± ± µa Input Coding See Tables and 2 Binary/Offset Binary 2

3 AD720, AD72 Electrical Specifications PARAMETER POWER SUPPLY CHARACTERISTICS Power Supply Rejection V+ = 4.V to.v (Note 3) (Figure 3) Functional Diagram V+ = +V, = +0V, T A = 2 o C Unless Otherwise Specified (Continued) TEST CONDITIONS AD720 AD72 MIN TYP MAX MIN TYP MAX ±0.00 ±0.00 % FSR/% V+ Power Supply Voltage Range + to + + to + V I+ All Digital Inputs at 0V or V+ ± ± µa Excluding Ladder Network All Digital Inputs High or Low 2 2 ma Excluding Ladder Network Total Power Dissipation Including the Ladder Network mw 2. Full Scale Range (FSR) is 0V for Unipolar and ±0V for Bipolar modes. 3. Using internal feedback resistor. 4. Guaranteed by design, or characterization and not production tested.. Accuracy not guaranteed unless outputs at potential.. Accuracy is tested and guaranteed at V+ = V only. UNITS 0kΩ 0kΩ 0kΩ 0kΩ SPDT NMOS SWITCHES MSB Switches shown for Digital Inputs High. Resistor values are typical. BIT 2 BIT 3 0kΩ Pin Descriptions AD720 AD72 PIN NAME DESCRIPTION IOUT Current Out summing junction of the R2R ladder network. 2 2 IOUT2 Current Out virtual ground, return path for the R2R ladder network. 3 3 Digital Ground. Ground potential for digital side of D/A. 4 4 Bits Most Significant Digital Data Bit. Bit 2 Digital Bit 2. Bit 3 Digital Bit Bit 4 Digital Bit Bit Digital Bit. 9 9 Bit Digital Bit. 0 0 Bit 7 Digital Bit 7. Bit 8 Digital Bit Bit 9 Digital Bit Bit 0 Digital Bit 0 (AD72). Least Significant Digital Data Bit (AD720). 4 Bit Digital Bit (AD72). Bit 2 Least Significant Digital Data Bit (AD72). 4 V+ Power Supply +V to +V. 7 Voltage Reference Input to set the output range. Supplies the R2R resistor ladder. 8 RFEEDBACK Feedback resistor used for the current to voltage conversion when using an external Op Amp. 3

4 AD720, AD72 Definition of Terms Nonlinearity: Error contributed by deviation of the DAC transfer function from a best straight line through the actual plot of transfer function. Normally expressed as a percentage of full scale range or in (sub)multiples of LSB. Resolution: It is addressing the smallest distinct analog output change that a D/A converter can produce. It is commonly expressed as the number of converter bits. A converter with resolution of N bits can resolve output changes of 2 N of the fullscale range, e.g., 2 N for a unipolar conversion. Resolution by no means implies linearity. Settling Time: Time required for the output of a DAC to settle to within specified error band around its final value (e.g., / 2 LSB) for a given digital input change, i.e., all digital inputs LOW to HIGH and HIGH to LOW. Gain Error: The difference between actual and ideal analog output values at full scale range, i.e., all digital inputs at HIGH state. It is expressed as a percentage of full scale range or in (sub)multiples of LSB. Feedthrough Error: Error caused by capacitive coupling from to with all digital inputs LOW. current reference and an operational amplifier are all that is required for most voltage output applications. A simplified equivalent circuit of the DAC is shown in the Functional Diagram. The NMOS SPDT switches steer the ladder leg currents between and buses which must be held either at ground potential. This configuration maintains a constant current in each ladder leg independent of the input code. Converter errors are further reduced by using separate metal interconnections between the major bits and the outputs. Use of high threshold switches reduce offset (leakage) errors to a negligible level. The level shifter circuits are comprised of three inverters with positive feedback from the output of the second to the first, see Figure. This configuration results in TTL/CMOS compatible operation over the full military temperature range. With the ladder SPDT switches driven by the level shifter, each switch is binarily weighted for an ON resistance proportional to the respective ladder leg current. This assures a constant voltage drop across each switch, creating equipotential terminations for the 2R ladder resistors and highly accurate leg currents. Output Capacitance: Capacitance from and terminals to ground. Output Leakage Current: Current which appears on terminal when all digital inputs are LOW or on terminal when all digital inputs are HIGH. V+ 3 4 TO LADDER 8 9 Detailed Description The AD720 and AD72 are monolithic, multiplying D/A converters. A highly stable thin film R2R resistor ladder network and NMOS SPDT switches form the basis of the converter circuit, CMOS level shifters permit low power TTL/CMOS compatible operation. An external voltage or DTL/TTL/ CMOS INPUT 2 7 FIGURE. CMOS LEVEL SHIFTER AND SWITCH Test Circuits The following test circuits apply for the AD720. Similar circuits are used for the AD72. 0BIT BINARY COUNTER CLOCK BIT (LSB) BIT BIT R FEEDBACK 4 I OUT AD720 HA200 I 3 OUT V 2BIT REFERENCE DAC 0kΩ 0.0% 0kΩ 0.0% MΩ HA200 + LINEARITY ERROR x 00 +0V BIT (LSB) +V UNGROUNDED SINE WAVE GENERATOR 40Hz V PP K 0.0% kω 0.0% 4 4 AD720 HA kΩ HA200 + V ERROR x 00 BIT 2 FIGURE 2. NONLINEARITY FIGURE 3. POWER SUPPLY REJECTION 4

5 AD720, AD72 Test Circuits The following test circuits apply for the AD720. Similar circuits are used for the AD72. (Continued) +V (ADJUST FOR V OUT = 0V) µf K +V 4 00Ω 0kΩ 4 2 AD720 0ALN V OUT 0kΩ kω 0.µF 0V f = khz BW = Hz QUAN TECH MODEL 34D WAVE ANALYZER +V BIT (LSB) NC +V 4 4 AD NC kω SCOPE 00mV PP MHz FIGURE 4. NOISE FIGURE. OUTPUT CAPACITANCE = 20V PP 00kHz SINE WAVE BIT (LSB) +V 4 4 AD HA200 V OUT + +V 0V +0V BIT DIGITAL INPUT (LSB) EXTRAPOLATE +V 4 4 AD mV Ω t: % SETTLING (mv) 8t: 0.03% SETTLING t = RISE TIME SCOPE FIGURE. FEEDTHROUGH ERROR FIGURE 7. OUTPUT CURRENT SETTLING TIME Applications Unipolar Binary Operation The circuit configuration for operating the AD720 in unipolar mode is shown in Figure 8. Similar circuits can be used for AD72. With positive and negative values the circuit is capable of 2Quadrant multiplication. The Digital Input Code/Analog Output Value table for unipolar mode is given in Table. DIGITAL INPUT BIT (LSB) +V 4 4 AD V OUT FIGURE 8. UNIPOLAR BINARY OPERATION (2QUADRANT MULTIPLICATION) TABLE. CODE TABLE UNlPOLAR BINARY OPERATION DIGITAL INPUT (2 N ) ANALOG OUTPUT ( / N ) /2 0 ( / 2 2 N ) (2 N ) LSB = 2 N. 2. N = 8 for 720 N = 0 for 72. Zero Offset Adjustment. Connect all digital inputs to. 2. Adjust the offset zero adjust trimpot of the output operational amplifier for 0V at V OUT. Gain Adjustment. Connect all digital inputs to V+. 2. Monitor V OUT for a (2 N ) reading. (N = 8 for AD720 and N = 0 for AD72).

6 AD720, AD72 3. To decrease V OUT, connect a series resistor (0 to 20Ω) between the reference voltage and the terminal. 4. To increase V OUT, connect a series resistor (0 to 20Ω) in the amplifier feedback loop. Bipolar (Offset Binary) Operation The circuit configuration for operating the AD720 in the bipolar mode is given in Figure 9. Similar circuits can be used for AD72. Using offset binary digital input codes and positive and negative reference voltage values, 4Quadrant multiplication can be realized. The Digital Input Code/Analog Output Value table for bipolar mode is given in Table 2. DIGITAL INPUT BIT (LSB) +V TABLE 2. BlPOLAR (OFFSET BINARY) CODE TABLE DIGITAL INPUT + R3 0MΩ 4 4 AD720 3 R 0K R2 0K % 0.0% + FIGURE 9. BIPOLAR OPERATION (4QUADRANT MULTIPLICATION) ANALOG OUTPUT V OUT A Logic input at any digital input forces the corresponding ladder switch to steer the bit current to IOUT bus. A Logic 0 input forces the bit current to IOUT2 bus. For any code the IOUT and IOUT2 bus currents are complements of one another. The current amplifier at IOUT2 changes the polarity of IOUT2 current and the transconductance amplifier at IOUT output sums the two currents. This configuration doubles the output range. The difference current resulting at zero offset binary code, (MSB = Logic, all other bits = Logic 0 ), is corrected by using an external resistor, (0MW), from VREF to IOUT2. Offset Adjustment. Adjust to approximately +0V. 2. Connect all digital inputs to Logic. 3. Adjust amplifier offset adjust trimpot for 0V ±mv at amplifier output. 4. Connect MSB (Bit ) to Logic and all other bits to Logic 0.. Adjust amplifier offset adjust trimpot for 0V ±mv at V OUT. Gain Adjustment. Connect all digital inputs to V+. 2. Monitor V OUT for a (2 (N) volts reading. (N = 8 for AD720, and N = 0 for AD72.). 3. To increase V OUT, connect a series resistor of up to 20Ω between V OUT and. 4. To decrease V OUT, connect a series resister of up to 20Ω between the reference voltage and the terminal. (2 (N) ) (2 (N) ) (2 (N) ) (2 (N) ) LSB = 2 (N). 2. N = 8 for 720 N = 0 for 72.

7 AD720, AD72 Die Characteristics DIE DIMENSIONS: 0 mils x 03 mils (2µm x 2µm) METALLIZATION: Type: Pure Aluminum Thickness: 0 ±kå PASSIVATION: Type: PSG/Nitride PSG: 7 ±.4kÅ Nitride: 8 ±.2kÅ PROCESS: CMOS Metal Gate Metallization Mask Layout AD720 PIN 7 BIT 4 PIN BIT 3 PIN BIT 2 PIN 4 BIT PIN 3 PIN 8 BIT PIN 2 I OUT 2 PIN I OUT PIN 9 BIT PIN 0 BIT 7 PIN PIN BIT 8 PIN PIN 4 V+ PIN 2 BIT 9 PIN 3 (LSB) NC NC 7

8 AD720, AD72 Die Characteristics DIE DIMENSIONS: 0 mils x 03 mils (2µm x 2µm) METALLIZATION: Type: Pure Aluminum Thickness: 0 ±kå PASSIVATION: Type: PSG/Nitride PSG: 7 ±.4kÅ Nitride: 8 ±.2kÅ PROCESS: CMOS Metal Gate Metallization Mask Layout AD72 PIN 7 BIT 4 PIN BIT 3 PIN BIT 2 PIN 4 BIT PIN 3 PIN 8 BIT PIN 2 I OUT 2 PIN I OUT PIN 9 BIT PIN 0 BIT 7 PIN 8 PIN BIT 8 PIN 7 PIN V+ PIN 2 BIT 9 PIN 3 PIN 4 BIT PIN BIT 2 (LSB) 8

9 AD720, AD72 DualInLine Plastic Packages (PDIP) INDEX AREA N 2 3 N/2 B A D E BASE PLANE A2 C A SEATING PLANE L C L D A e D A B e e C C B e B 0.00 (0.2) M C A B S. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y4.M Symbols are defined in the MO Series Symbol List in Section 2.2 of Publication No Dimensions A, A and L are measured with the package seated in JE DEC seating plane gauge GS3.. D, D, and E dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.00 inch (0.2mm).. E and e A are measured with the leads constrained to be perpendicular to datum C. 7. e B and e C are measured at the lead tips with the leads unconstrained. e C must be zero or greater. 8. B maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.00 inch (0.2mm). 9. N is the maximum number of terminal positions. 0. Corner leads (, N, N/2 and N/2 + ) for E8.3, E.3, E8.3, E28.3, E42. will have a B dimension of inch (0.7.4mm). E E.3 (JEDEC MS00BB ISSUE D) LEAD DUALINLINE PLASTIC PACKAGE INCHES MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A A A B B , 0 C D D E E e 0.00 BSC 2.4 BSC e A BSC 7.2 BSC e B L N 9 Rev. 0 2/93 9

10 AD720, AD72 DualInLine Plastic Packages (PDIP) INDEX AREA BASE PLANE SEATING PLANE D B C A N 2 3 N/2 B D e D E. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y4.M Symbols are defined in the MO Series Symbol List in Section 2.2 of Publication No Dimensions A, A and L are measured with the package seated in JEDEC seating plane gauge GS3.. D, D, and E dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.00 inch (0.2mm).. E and e A are measured with the leads constrained to be perpendicular to datum C. 7. e B and e C are measured at the lead tips with the leads unconstrained. e C must be zero or greater. 8. B maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.00 inch (0.2mm). 9. N is the maximum number of terminal positions. 0. Corner leads (, N, N/2 and N/2 + ) for E8.3, E.3, E8.3, E28.3, E42. will have a B dimension of inch (0.7.4mm). B A 0.00 (0.2) M C A A2 L B S A e C E C L e A C e B E8.3 (JEDEC MS00BC ISSUE D) 8 LEAD DUALINLINE PLASTIC PACKAGE INCHES MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A A A B B , 0 C D D E E e 0.00 BSC 2.4 BSC e A BSC 7.2 BSC e B L N Rev. 0 2/93 All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation s quality certifications can be viewed at website Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site 0

Data Sheet June Features. Pinout

Data Sheet June Features. Pinout NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 888INTERSIL or www.intersil.com/tsc 0Bit Multiplying D/A Converter The AD7533 is a monolithic, low cost,

More information

Features. V REF IN 10k 10k 10k 10k. 10k (17) 20k SPDT NMOS SWITCHES R FEEDBACK (18) BIT 6 MSB (4) AD7541JN 0.02% (11-Bit) 0 to Ld PDIP E18.

Features. V REF IN 10k 10k 10k 10k. 10k (17) 20k SPDT NMOS SWITCHES R FEEDBACK (18) BIT 6 MSB (4) AD7541JN 0.02% (11-Bit) 0 to Ld PDIP E18. AD7 Bit, Multiplying D/A Converter OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT AD7 DATASHEET FN07 Rev..00 The AD7 is a monolithic, low cost, high performance, bit accurate, multiplying digitaltoanalog

More information

HA Features. 12MHz, High Input Impedance, Operational Amplifier. Applications. Pinout. Part Number Information. Data Sheet May 2003 FN2893.

HA Features. 12MHz, High Input Impedance, Operational Amplifier. Applications. Pinout. Part Number Information. Data Sheet May 2003 FN2893. OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 HA-2515 Data Sheet May 23 FN2893.5 12MHz, High Input Impedance, Operational Amplifier HA-2515 is a high performance operational amplifier which sets

More information

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5 HA-4741 Data Sheet July 24 FN2922. Quad, 3.MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational

More information

DATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier

DATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier 12MHz, High Input Impedance, Operational Amplifier OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 DATASHEET FN289 Rev 6. HA-255 is an operational amplifier whose design is optimized to deliver excellent

More information

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8.

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8. DATASHEET HA-4741 Quad, 3.5MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each

More information

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8 HA-533 Data Sheet February 6, 26 FN2924.8 25MHz Video Buffer The HA-533 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 25MHz and

More information

HA Features. 400MHz, Fast Settling Operational Amplifier. Applications. Ordering Information. Pinout. Data Sheet August 2002 FN2897.

HA Features. 400MHz, Fast Settling Operational Amplifier. Applications. Ordering Information. Pinout. Data Sheet August 2002 FN2897. HA-5 Data Sheet August FN97. MHz, Fast Settling Operational Amplifier The Intersil HA-5 is a wideband, very high slew rate, monolithic operational amplifier featuring superior speed and bandwidth characteristics.

More information

TD E1 Systèmes électroniques non linéaires DATASHEET

TD E1 Systèmes électroniques non linéaires DATASHEET TD E1 TD E1 Systèmes électroniques non linéaires DATASHEET Datasheet AD7520 Datasheet DAC0800 camps@laas.fr helene.leymarie@univ-tlse3.fr thierryperisse@free.fr http://thierryperisse.free.fr Intervenants

More information

HA MHz, PRAM Four Channel Programmable Amplifiers. Features. Applications. Pinout. Ordering Information

HA MHz, PRAM Four Channel Programmable Amplifiers. Features. Applications. Pinout. Ordering Information HA0 Data Sheet August 00 FN89. 0MHz, PRAM Four Channel Programmable Amplifiers The HA0 comprise a series of fourchannel programmable amplifiers providing a level of versatility unsurpassed by any other

More information

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12.

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12. 25MHz Video Buffer NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at -888-INTERSIL or www.intersil.com/tsc DATASHEET FN2924 Rev 8. The HA-533 is a unity

More information

HA Features. 650ns Precision Sample and Hold Amplifier. Applications. Functional Diagram. Ordering Information. Pinout

HA Features. 650ns Precision Sample and Hold Amplifier. Applications. Functional Diagram. Ordering Information. Pinout HA-50 Data Sheet June 200 FN2858.5 650ns Precision Sample and Hold Amplifier The HA-50 is a very fast sample and hold amplifier designed primarily for use with high speed A/D converters. It utilizes the

More information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information DATASHEET 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers FN2894 Rev 1. comprise a series of operational amplifiers delivering an unsurpassed combination of specifications

More information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information HA-22, HA-22 Data Sheet August, 2 FN2894. 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-22/22 comprise a series of operational amplifiers delivering an unsurpassed

More information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,

More information

DATASHEET CA Applications. Pinout. Ordering Information. General Purpose NPN Transistor Array. FN483 Rev.6.00 Page 1 of 7.

DATASHEET CA Applications. Pinout. Ordering Information. General Purpose NPN Transistor Array. FN483 Rev.6.00 Page 1 of 7. DATASHEET CA-386 General Purpose NPN Transistor Array The CA386 consists of five general-purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected

More information

HI-200, HI-201. Dual/Quad SPST, CMOS Analog Switches. Features. Applications. Ordering Information. Functional Diagram FN3121.8

HI-200, HI-201. Dual/Quad SPST, CMOS Analog Switches. Features. Applications. Ordering Information. Functional Diagram FN3121.8 HI-200, HI-201 Data Sheet FN3121.8 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds

More information

HA-2520, HA-2522, HA-2525

HA-2520, HA-2522, HA-2525 HA-, HA-, HA- Data Sheet September 99 File Number 9. MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-// comprise a series of operational amplifiers delivering an unsurpassed

More information

HI-201HS. Features. High Speed, Quad SPST, CMOS Analog Switch. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) FN3123.

HI-201HS. Features. High Speed, Quad SPST, CMOS Analog Switch. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) FN3123. HI-HS Data Sheet September 4 FN.4 High Speed, Quad SPST, CMOS Analog Switch The HI-HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit

More information

CMOS 8-Bit Buffered Multiplying DAC AD7524

CMOS 8-Bit Buffered Multiplying DAC AD7524 a FEATURES Microprocessor Compatible (6800, 8085, Z80, Etc.) TTL/ CMOS Compatible Inputs On-Chip Data Latches Endpoint Linearity Low Power Consumption Monotonicity Guaranteed (Full Temperature Range) Latch

More information

CA3096, CA3096A, CA3096C

CA3096, CA3096A, CA3096C January OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HFA39 CA39, CA39A, CA39C NPN/PNP Transistor Arrays Applications Five-Independent Transistors - Three NPN and - Two PNP Differential Amplifiers DC Amplifiers

More information

CA3102. Dual High Frequency Differential Amplifier For Low Power Applications Up to 500MHz. Features. Applications. Ordering Information.

CA3102. Dual High Frequency Differential Amplifier For Low Power Applications Up to 500MHz. Features. Applications. Ordering Information. CA Data Sheet November 999 File Number 6.6 Dual High Frequency Differential Amplifier For Low Power Applications Up to MHz The CA consists of two independent differential amplifiers with associated constant

More information

HA, HA Absolute Maximum Ratings Supply Voltage Between V+ and V Terminals V Differential Input Voltage V

HA, HA Absolute Maximum Ratings Supply Voltage Between V+ and V Terminals V Differential Input Voltage V HA, HA Data Sheet October 6, FN9.9 Dual and Quad, 8MHz, Low Noise Operational Amplifiers Low noise and high performance are key words describing HA and HA. These general purpose amplifiers offer an array

More information

HI Bit, 40 MSPS, High Speed D/A Converter

HI Bit, 40 MSPS, High Speed D/A Converter October 6, 005 Pb-Free and RoHS Compliant HI7 -Bit, 40 MSPS, High Speed D/A Converter Features Throughput Rate......................... 40MHz Resolution................................ -Bit Integral Linearity

More information

HA-2520, HA-2522, HA-2525

HA-2520, HA-2522, HA-2525 HA-, HA-, HA- Data Sheet November, 6 FN894.8 MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-, HA-, HA- comprise a series of operational amplifiers delivering an unsurpassed

More information

DATASHEET CD22M3494. Features. Applications. Block Diagram. 16 x 8 x 1 BiMOS-E Crosspoint Switch. FN2793 Rev 8.00 Page 1 of 10.

DATASHEET CD22M3494. Features. Applications. Block Diagram. 16 x 8 x 1 BiMOS-E Crosspoint Switch. FN2793 Rev 8.00 Page 1 of 10. DATASHEET CD22M3494 16 x 8 x 1 BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 128 analog switches capable of handling signals from DC to video. Because of the switch structure, input signals

More information

DATASHEET HI-1818A. Features. Applications. Ordering Information. Pinout. Low Resistance, Single 8-Channel, CMOS Analog Multiplexer

DATASHEET HI-1818A. Features. Applications. Ordering Information. Pinout. Low Resistance, Single 8-Channel, CMOS Analog Multiplexer NOT RECOMMDED FOR NEW DESIGNS NO RECOMMDED REPLACEMT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Low Resistance, Single 8-Channel, CMOS Analog Multiplexer DATASHEET FN3141

More information

DATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00.

DATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00. DATASHEET Low Voltage Reference The is a 1.2V temperature-compensated voltage reference. It uses the band-gap principle to achieve excellent stability and low noise at reverse currents down to 50 A. Applications

More information

HIP V, 300mA Three Phase High Side Driver. Features. Applications. Ordering Information. Pinout. July 2004

HIP V, 300mA Three Phase High Side Driver. Features. Applications. Ordering Information. Pinout. July 2004 HIP0 Data Sheet July 00 FN. 0V, 00mA Three Phase High Side Driver The HIP0 is a three phase high side N-channel MOSFET driver, specifically targeted for PWM motor control. Two HIP0 may be used together

More information

MARKING RANGE ( C) PACKAGE DWG. # HA-2600 (METAL CAN)

MARKING RANGE ( C) PACKAGE DWG. # HA-2600 (METAL CAN) DATASHEET 2MHz, High Input Impedance Operational Amplifier is an internally compensated bipolar operational amplifier that features very high input impedance (5M coupled with wideband AC performance. The

More information

DATASHEET CA3096, CA3096A, CA3096C. Description. Applications. CA3096, CA3096A, CA3096C Essential Differences. Part Number Information.

DATASHEET CA3096, CA3096A, CA3096C. Description. Applications. CA3096, CA3096A, CA3096C Essential Differences. Part Number Information. DATASHEET CA39, CA39A, CA39C NPN/PNP Transistor Arrays Applications Five-Independent Transistors - Three NPN and - Two PNP Differential Amplifiers DC Amplifiers Sense Amplifiers Level Shifters Timers Lamp

More information

DATASHEET HI-201HS. Features. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) High Speed, Quad SPST, CMOS Analog Switch

DATASHEET HI-201HS. Features. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) High Speed, Quad SPST, CMOS Analog Switch DATASHEET HI-21HS High Speed, Quad SPST, CMOS Analog Switch The HI-21HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit consists of

More information

DATASHEET HA Features. Applications. Ordering Information. Pinout. 400MHz, Fast Settling Operational Amplifier. FN2897 Rev.5.

DATASHEET HA Features. Applications. Ordering Information. Pinout. 400MHz, Fast Settling Operational Amplifier. FN2897 Rev.5. DATASHEET MHz, Fast Settling Operational Amplifier The Intersil is a wideband, very high slew rate, monolithic operational amplifier featuring superior speed and bandwidth characteristics. Bipolar construction

More information

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts HA-264, HA-2645 Data Sheet January 3, 26 FN294.5 4MHz, High Supply Voltage Operational Amplifiers HA-264 and HA-2645 are monolithic operational amplifiers which are designed to deliver unprecedented dynamic

More information

DATASHEET HA-5137A. Features. Applications. Ordering Information. Pinout. 63MHz, Ultra-Low Noise Precision Operational Amplifier

DATASHEET HA-5137A. Features. Applications. Ordering Information. Pinout. 63MHz, Ultra-Low Noise Precision Operational Amplifier DATASHEET HA-5137A 3MHz, Ultra-Low Noise Precision Operational Amplifier The HA-5137 operational amplifier features an unparalleled combination of precision DC and wideband high speed characteristics.

More information

CA124, CA224, CA324, LM324, LM2902

CA124, CA224, CA324, LM324, LM2902 OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT CA, CA, CA, LM, LM9 Data Sheet May File Number 796.5 itle 9 b- ad, Hz, raal plis i- - -, usl, lis) tho y- ds er- Quad, MHz, Operational Amplifiers for Commercial,

More information

HA MHz, Fast Settling Operational Amplifier. Features. Applications. Pinout. Part Number Information. Data Sheet November 19, 2004 FN2914.

HA MHz, Fast Settling Operational Amplifier. Features. Applications. Pinout. Part Number Information. Data Sheet November 19, 2004 FN2914. OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 888TERSIL or www.intersil.com/tsc HA595 Data Sheet November 9, 2 FN29.6 5MHz, Fast Settling Operational Amplifier The

More information

HA-2602/883. Wideband, High Impedance Operational Amplifier. Description. Features. Applications. Part Number Information. Pinout.

HA-2602/883. Wideband, High Impedance Operational Amplifier. Description. Features. Applications. Part Number Information. Pinout. October 2004 OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Wideband, High Impedance Operational Amplifier Features This Circuit

More information

SP720. Electronic Protection Array for ESD and Over-Voltage Protection. Features. [ /Title (SP720 ) /Subject. (Electronic.

SP720. Electronic Protection Array for ESD and Over-Voltage Protection. Features. [ /Title (SP720 ) /Subject. (Electronic. SP70 Data Sheet January 99 File Number 79.0 [ /Title (SP70 ) /Subject (Electronic Protection Array for ESD and Over Voltage Protection) /Autho r () /Keywords (TVS, Transient Suppression, Protection, ESD,

More information

Features TEMP. RANGE ( C)

Features TEMP. RANGE ( C) DATASHEET HFA0, HFA09, HFA27, HFA28 Ultra High Frequency Transistor Arrays The HFA0, HFA09, HFA27 and the HFA28 are Ultra High Frequency Transistor Arrays that are fabricated from Intersil Corporation

More information

DATASHEET. Features. Applications. Pin Configuration HA-5147 (CERDIP) TOP VIEW. Ordering Information HA-5147

DATASHEET. Features. Applications. Pin Configuration HA-5147 (CERDIP) TOP VIEW. Ordering Information HA-5147 DATASHEET HA-517 12MHz, Ultra-Low Noise Precision Operational Amplifiers FN291 Rev 1. The HA-517 operational amplifier features an unparalleled combination of precision DC and wideband high speed characteristics.

More information

DATASHEET HI-200, HI-201. Features. Applications. Ordering Information. Functional Diagram. Dual/Quad SPST, CMOS Analog Switches

DATASHEET HI-200, HI-201. Features. Applications. Ordering Information. Functional Diagram. Dual/Quad SPST, CMOS Analog Switches DATASHEET HI-200, HI-201 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200

More information

DATASHEET HFA1112. Features. Applications. Related Literature. Pin Descriptions. Ordering Information

DATASHEET HFA1112. Features. Applications. Related Literature. Pin Descriptions. Ordering Information DATASHEET HFA1112 85MHz, Low Distortion Programmable Gain Buffer Amplifiers FN2992 Rev 8. July 27, 25 The HFA1112 is a closed loop Buffer featuring user programmable gain and ultra high speed performance.

More information

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table TM Data Sheet June 2000 File Number 3990.6 480MHz, SOT-23, Video Buffer with Output Disable The is a very wide bandwidth, unity gain buffer ideal for professional video switching, HDTV, computer monitor

More information

CA3338, CA3338A. CMOS Video Speed, 8-Bit, 50 MSPS, R2R D/A Converters. Features. Applications. Ordering Information. Pinout FN1850.

CA3338, CA3338A. CMOS Video Speed, 8-Bit, 50 MSPS, R2R D/A Converters. Features. Applications. Ordering Information. Pinout FN1850. CA3338, CA3338A Data Sheet May 2003 FN1850.3 CMOS Video Speed, 8-Bit, 50 MSPS, 2 D/A Converters The CA3338 family are CMOS/SOS high speed 2 voltage output digital-to-analog converters. They can operate

More information

TEMP. PKG. -IN 1 16 S/H CONTROL PART NUMBER RANGE

TEMP. PKG. -IN 1 16 S/H CONTROL PART NUMBER RANGE DATASHEET 7ns, Low Distortion, Precision Sample and Hold Amplifier FN59 Rev 5. The combines the advantages of two sample/ hold architectures to create a new generation of monolithic sample/hold. High amplitude,

More information

DATASHEET HI-524. Features. Applications. Functional Diagram. Ordering Information. Pinout. 4-Channel Wideband and Video Multiplexer

DATASHEET HI-524. Features. Applications. Functional Diagram. Ordering Information. Pinout. 4-Channel Wideband and Video Multiplexer DATASHEET HI-524 4-Channel Wideband and Video Multiplexer The HI-524 is a 4-Channel CMOS analog multiplexer designed to process single-ended signals with bandwidths up to 10MHz. The chip includes a 1 of

More information

CA3096, CA3096A, CA3096C

CA3096, CA3096A, CA3096C December 99 Applications Five-Independent Transistors - Three NPN and - Two PNP Differential Amplifiers DC Amplifiers Sense Amplifiers Level Shifters Timers Lamp and Relay Drivers Thyristor Firing Circuits

More information

POSSIBLE SUBSTITUTE PRODUCT HA-2842, HA-2544

POSSIBLE SUBSTITUTE PRODUCT HA-2842, HA-2544 OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA2842, HA2544 5MHz, Fast Settling, Unity Gain Stable, Video Operational Amplifier DATASHEET FN2843 Rev 4. The HA2841 is a wideband, unity gain stable, operational

More information

12-Bit Successive-Approximation Integrated Circuit ADC ADADC80

12-Bit Successive-Approximation Integrated Circuit ADC ADADC80 2-Bit Successive-Approximation Integrated Circuit ADC FEATURES True 2-bit operation: maximum nonlinearity ±.2% Low gain temperature coefficient (TC): ±3 ppm/ C maximum Low power: 8 mw Fast conversion time:

More information

CMOS 12-Bit Serial Input Multiplying DIGITAL-TO-ANALOG CONVERTER

CMOS 12-Bit Serial Input Multiplying DIGITAL-TO-ANALOG CONVERTER CMOS 12-Bit Serial Input Multiplying DIGITAL-TO-ANALOG CONVERTER FEATURES 12-BICCURACY IN 8-PIN MINI-DIP AND 8-PIN SOIC FAST 3-WIRE SERIAL INTERFACE LOW INL AND DNL: ±1/2 LSB max GAIN ACCURACY TO ±1LSB

More information

High Precision 10 V IC Reference AD581

High Precision 10 V IC Reference AD581 High Precision 0 V IC Reference FEATURES Laser trimmed to high accuracy 0.000 V ±5 mv (L and U models) Trimmed temperature coefficient 5 ppm/ C maximum, 0 C to 70 C (L model) 0 ppm/ C maximum, 55 C to

More information

DATASHEET HI1171. Ordering Information. Typical Application Circuit. Pinout. 8-Bit, 40 MSPS, High Speed D/A Converter. FN3662 Rev.3.

DATASHEET HI1171. Ordering Information. Typical Application Circuit. Pinout. 8-Bit, 40 MSPS, High Speed D/A Converter. FN3662 Rev.3. -Bit, 40 MSPS, High Speed D/A Converter Pb-Free and RoHS Compliant DATASHEET FN366 Rev.3.00 Features Throughput Rate.......................... 40MHz Resolution.................................-Bit Integral

More information

LC2 MOS Octal 8-Bit DAC AD7228A

LC2 MOS Octal 8-Bit DAC AD7228A a FEATURES Eight 8-Bit DACs with Output Amplifiers Operates with Single +5 V, +12 V or +15 V or Dual Supplies P Compatible (95 ns WR Pulse) No User Trims Required Skinny 24-Pin DlPs, SOIC, and 28-Terminal

More information

High Speed 12-Bit Monolithic D/A Converters AD565A/AD566A

High Speed 12-Bit Monolithic D/A Converters AD565A/AD566A a FEATURES Single Chip Construction Very High Speed Settling to 1/2 AD565A: 250 ns max AD566A: 350 ns max Full-Scale Switching Time: 30 ns Guaranteed for Operation with 12 V (565A) Supplies, with 12 V

More information

12-Bit Successive-Approximation Integrated Circuit A/D Converter AD ADC80

12-Bit Successive-Approximation Integrated Circuit A/D Converter AD ADC80 a 2-Bit Successive-Approximation Integrated Circuit A/D Converter FEATURES True 2-Bit Operation: Max Nonlinearity.2% Low Gain T.C.: 3 ppm/ C Max Low Power: 8 mw Fast Conversion Time: 25 s Precision 6.3

More information

DATASHEET EL7104. Features. Ordering Information. Applications. Pinout. High Speed, Single Channel, Power MOSFET Driver. FN7113 Rev 2.

DATASHEET EL7104. Features. Ordering Information. Applications. Pinout. High Speed, Single Channel, Power MOSFET Driver. FN7113 Rev 2. DATASHEET EL7104 High Speed, Single Channel, Power MOSFET Driver FN7113 Rev 2.00 The EL7104 is a matched driver IC that improves the operation of the industry-standard TC-4420/29 clock drivers. The Elantec

More information

HA Microsecond Precision Sample and Hold Amplifier. Features. Applications. Pinouts. Ordering Information. Data Sheet August 24, 2005 FN2857.

HA Microsecond Precision Sample and Hold Amplifier. Features. Applications. Pinouts. Ordering Information. Data Sheet August 24, 2005 FN2857. Data Sheet FN85. Microsecond Precision Sample and Hold Amplifier The was designed for use in precision, high speed data acquisition systems. The circuit consists of an input transconductance amplifier

More information

Low Cost 10-Bit Monolithic D/A Converter AD561

Low Cost 10-Bit Monolithic D/A Converter AD561 a FEATURES Complete Current Output Converter High Stability Buried Zener Reference Laser Trimmed to High Accuracy (1/4 LSB Max Error, AD561K, T) Trimmed Output Application Resistors for 0 V to +10 V, 5

More information

CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTER Microprocessor Compatible

CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTER Microprocessor Compatible CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTER Microprocessor Compatible FEATURES FOUR-QUADRANT MULTIPLICATION LOW GAIN TC: 2ppm/ C typ MONOTONICITY GUARANTEED OVER TEMPERATURE SINGLE 5V TO 15V SUPPLY

More information

Quad 12-Bit Digital-to-Analog Converter (Serial Interface)

Quad 12-Bit Digital-to-Analog Converter (Serial Interface) Quad 1-Bit Digital-to-Analog Converter (Serial Interface) FEATURES COMPLETE QUAD DAC INCLUDES INTERNAL REFERENCES AND OUTPUT AMPLIFIERS GUARANTEED SPECIFICATIONS OVER TEMPERATURE GUARANTEED MONOTONIC OVER

More information

DATASHEET CA3127. Features. Applications. Ordering Information. Pinout. High Frequency NPN Transistor Array. FN662 Rev.5.00 Page 1 of 9.

DATASHEET CA3127. Features. Applications. Ordering Information. Pinout. High Frequency NPN Transistor Array. FN662 Rev.5.00 Page 1 of 9. DATASHEET CA1 High Frequency NPN Transistor Array The CA1 consists of five general purpose silicon NPN transistors on a common monolithic substrate. Each of the completely isolated transistors exhibits

More information

HA MHz Video Buffer. Description. Features. Applications. Ordering Information. Pinouts. April 1997

HA MHz Video Buffer. Description. Features. Applications. Ordering Information. Pinouts. April 1997 SEMICONDUCTOR HA-533 April 997 25MHz Video Buffer Features Differential Phase Error...............2 Degrees Differential Gain Error......................3% High Slew Rate......................... /µs Wide

More information

HA Quad, 3.5MHz, Operational Amplifier. Description. Features. Applications. Ordering Information. Pinouts. November 1996

HA Quad, 3.5MHz, Operational Amplifier. Description. Features. Applications. Ordering Information. Pinouts. November 1996 SEMICONDUCTOR HA4741 November 1996 Features Slew Rate...............................1.6V/µs Bandwidth................................MHz Input Voltage Noise...................... 9nV/ Hz Input Offset Voltage.........................mV

More information

CA5260, CA5260A. 3MHz, BiMOS Microprocessor Operational Amplifiers with MOSFET Input/CMOS Output. Features. Description.

CA5260, CA5260A. 3MHz, BiMOS Microprocessor Operational Amplifiers with MOSFET Input/CMOS Output. Features. Description. , A November 1996 3MHz, BiMOS Microprocessor Operational Amplifiers with MOSFET Input/CMOS Output Features Description MOSFET Input Stage provides - Very High Z I = 1.5TΩ (1.5 x 10 12 Ω) (Typ) - Very Low

More information

DATASHEET HA-5127/883. Features. Applications. Ordering Information. Pinout. Ultra Low Noise, Precision Operational Amplifier

DATASHEET HA-5127/883. Features. Applications. Ordering Information. Pinout. Ultra Low Noise, Precision Operational Amplifier Ultra Low Noise, Precision Operational Amplifier NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc DATASHEET FN3751

More information

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8187 Rev 1.

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8187 Rev 1. DATASHEET X93255 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93255 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a

More information

HA5023. Dual 125MHz Video Current Feedback Amplifier. Features. Applications. Ordering Information. Pinout. Data Sheet September 30, 2015 FN3393.

HA5023. Dual 125MHz Video Current Feedback Amplifier. Features. Applications. Ordering Information. Pinout. Data Sheet September 30, 2015 FN3393. HA523 Data Sheet September 3, 215 FN3393.9 Dual 125MHz Video Current Feedback Amplifier The HA523 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1

More information

Features. NOTE: Non-designated pins are no connects and are not electrically connected internally.

Features. NOTE: Non-designated pins are no connects and are not electrically connected internally. OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Data Sheet December 1995, Rev. G EL2001 FN7020 Low Power, 70MHz Buffer Amplifier

More information

DATASHEET HA Features. Applications. Pinout. Ordering Information. 3.2µs Sample and Hold Amplifiers. FN2856 Rev.7.

DATASHEET HA Features. Applications. Pinout. Ordering Information. 3.2µs Sample and Hold Amplifiers. FN2856 Rev.7. 3.2µs Sample and Hold Amplifiers NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888TERSIL or www.intersil.com/tsc DATASHEET FN2856 Rev.7.00 The HA-2420

More information

CD22M x 8 x 1 BiMOS-E Crosspoint Switch. Features. Applications. Block Diagram FN Data Sheet January 16, 2006

CD22M x 8 x 1 BiMOS-E Crosspoint Switch. Features. Applications. Block Diagram FN Data Sheet January 16, 2006 CD22M3494 Data Sheet FN2793.7 6 x 8 x BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 28 analog switches capable of handling signals from DC to video. Because of the switch structure, input

More information

DACPORT Low Cost, Complete P-Compatible 8-Bit DAC AD557*

DACPORT Low Cost, Complete P-Compatible 8-Bit DAC AD557* a FEATURES Complete 8-Bit DAC Voltage Output 0 V to 2.56 V Internal Precision Band-Gap Reference Single-Supply Operation: 5 V ( 10%) Full Microprocessor Interface Fast: 1 s Voltage Settling to 1/2 LSB

More information

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8186 Rev 1.

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8186 Rev 1. DATASHEET X93254 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93254 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a

More information

Microprocessor-Compatible 12-Bit D/A Converter AD667*

Microprocessor-Compatible 12-Bit D/A Converter AD667* a FEATURES Complete 12-Bit D/A Function Double-Buffered Latch On Chip Output Amplifier High Stability Buried Zener Reference Single Chip Construction Monotonicity Guaranteed Over Temperature Linearity

More information

POSSIBLE SUBSTITUTE PRODUCT HA-2525, HA-2842

POSSIBLE SUBSTITUTE PRODUCT HA-2525, HA-2842 HA511 1MHz, Low Noise, Operational Amplifiers OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA2525, HA282 DATASHEET FN295 Rev 5. May 2 The HA511 is a dielectrically isolated operational amplifier featuring

More information

CA741, CA741C, CA1458, CA1558, LM741, LM741C, LM1458

CA741, CA741C, CA1458, CA1558, LM741, LM741C, LM1458 OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT CA, CAC, CA, CA, LM, LMC, LM Data Sheet May File Number. tle M le l, h s raal pli li.9mhz Single and Dual, High Gain Operational Amplifiers for Military, Industrial

More information

DATASHEET ISL6700. Features. Ordering Information. Applications. Pinouts. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver

DATASHEET ISL6700. Features. Ordering Information. Applications. Pinouts. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver DATASHEET ISL6700 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver FN9077 Rev.6.00 The ISL6700 is an 80V/1.25A peak, medium frequency, low cost, half-bridge driver IC available in 8-lead

More information

DATASHEET ISL6208. Features. Applications. Related Literature. Ordering Information. Pinout. High Voltage Synchronous Rectified Buck MOSFET Driver

DATASHEET ISL6208. Features. Applications. Related Literature. Ordering Information. Pinout. High Voltage Synchronous Rectified Buck MOSFET Driver NOT RECOMMENDED FOR NEW DESIGNS POSSIBLE SUBSTITUTE PRODUCT ISL6208 High Voltage Synchronous Rectified Buck MOSFET Driver DATASHEET FN9047 Rev 0.00 The ISL6205 is a high-voltage, high-frequency, dual MOSFET

More information

Description PWM INPUT CLK MODULATOR LOGIC 8 - STAGE RIPPLE COUNTER FREQUENCY DATA REGISTER 8 - STAGE SHIFT REGISTER SCK

Description PWM INPUT CLK MODULATOR LOGIC 8 - STAGE RIPPLE COUNTER FREQUENCY DATA REGISTER 8 - STAGE SHIFT REGISTER SCK TM CDP8HC8W March 998 CMOS Serial Digital Pulse Width Modulator Features Programmable Frequency and Duty Cycle Output Serial Bus Input; Compatible with Motorola/Intersil SPI Bus, Simple Shift-Register

More information

DATASHEET HA-5102, HA Pinouts. Ordering Information. Features. Applications. Dual and Quad, 8MHz, Low Noise Operational Amplifiers

DATASHEET HA-5102, HA Pinouts. Ordering Information. Features. Applications. Dual and Quad, 8MHz, Low Noise Operational Amplifiers DATASHEET HA-512, HA-514 Dual and Quad, 8Hz, Low Noise Operational Amplifiers FN2925 Rev 9. October 26, 24 Low noise and high performance are key words describing HA-512 and HA-514. These general purpose

More information

ISL6536A. Four Channel Supervisory IC. Features. Applications. Typical Application Schematic. Ordering Information. Data Sheet May 2004 FN9136.

ISL6536A. Four Channel Supervisory IC. Features. Applications. Typical Application Schematic. Ordering Information. Data Sheet May 2004 FN9136. ISL6536A Data Sheet May 2004 FN9136.1 Four Channel Supervisory IC The ISL6536A is a four channel supervisory IC designed to monitor voltages >, = 0.7V. This IC bias range is from 2.7V to 5V but can supervise

More information

CA3262A, CA3262. Quad-Gated, Inverting Power Drivers. Features. Description. Ordering Information. Pinouts. August 1997

CA3262A, CA3262. Quad-Gated, Inverting Power Drivers. Features. Description. Ordering Information. Pinouts. August 1997 Semiconductor CA6A, CA6 August 997 Quad-Gated, Inverting Power Drivers Features Independent Over-Current Limiting On Each Output Independent Over-Temperature Limiting On Each Output Output Drivers Capable

More information

DATASHEET HC5503T. Features. Applications. Ordering Information. Block Diagram. Balanced PBX/Key System SLIC, Subscriber Line Interface Circuit

DATASHEET HC5503T. Features. Applications. Ordering Information. Block Diagram. Balanced PBX/Key System SLIC, Subscriber Line Interface Circuit NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART HC5503PRC Balanced PBX/Key System SLIC, Subscriber Line Interface Circuit DATASHEET FN4506 Rev 2.00 The Intersil HC5503T is a low cost Subscriber

More information

Features PKG. DWG. # M16.3 M16.3 M16.3 M16.15 M16.15 M16.15 E16.3. NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN HIN232A +5V Capacitors No/No 0

Features PKG. DWG. # M16.3 M16.3 M16.3 M16.15 M16.15 M16.15 E16.3. NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN HIN232A +5V Capacitors No/No 0 DATASHEET HINA High Speed V Powered RS Transmitters/Receivers FN Rev.00 The HINA highspeed RS transmitter/receiver interface circuit meets all ElA highspeed RSE and V. specifications, and is particularly

More information

SP723 Lead-Free/Green

SP723 Lead-Free/Green TVS Diode Arrays The SP73 is an array of SCR/Diode bipolar structures for ESD and over-voltage protection of sensitive input circuits. The SP73 has protection SCR/Diode device structures per input. There

More information

DATASHEET HI-565A. Features. Applications. Ordering Information. Pinout. Functional Diagram. High Speed, Monolithic D/A Converter with Reference

DATASHEET HI-565A. Features. Applications. Ordering Information. Pinout. Functional Diagram. High Speed, Monolithic D/A Converter with Reference DATASHEET HI565A High Speed, Monolithic D/A Converter with Reference The HI565A is a fast, 12bit, current output, digitaltoanalog converter. The monolithic chip includes a precision voltage reference,

More information

DATASHEET HD Features. Ordering Information. CMOS Programmable Bit Rate Generator. FN2954 Rev 2.00 Page 1 of 8. August 24, FN2954 Rev 2.

DATASHEET HD Features. Ordering Information. CMOS Programmable Bit Rate Generator. FN2954 Rev 2.00 Page 1 of 8. August 24, FN2954 Rev 2. D-4702 CMOS Programmable Bit Rate Generator NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPACEMENT contact our Technical Support Center at 1-888-INTERSI or www.intersil.com/tsc DATASEET FN2954 Rev 2.00

More information

Quad 8-Bit Multiplying CMOS D/A Converter with Memory DAC8408

Quad 8-Bit Multiplying CMOS D/A Converter with Memory DAC8408 a FEATURES Four DACs in a 28 Pin, 0.6 Inch Wide DIP or 28-Pin JEDEC Plastic Chip Carrier 1/4 LSB Endpoint Linearity Guaranteed Monotonic DACs Matched to Within 1% Microprocessor Compatible Read/Write Capability

More information

DATASHEET HI-200/883. Features. Applications. Functional Diagram. Ordering Information. Pinout. Dual SPST CMOS Analog Switch

DATASHEET HI-200/883. Features. Applications. Functional Diagram. Ordering Information. Pinout. Dual SPST CMOS Analog Switch Dual PT CMO Analog witch NOT RECOMMENDED FOR NEW DEIGN NO RECOMMENDED REPLACEMENT contact our Technical upport Center at 1-888-INTERIL or www.intersil.com/tsc DATAHEET FN6059 Rev 2.00 The HI-200/883 is

More information

DATASHEET. Features. Applications. Pin Configuration. Ordering Information HI-201/883. Quad SPST CMOS Analog Switch. FN7990 Rev.0.

DATASHEET. Features. Applications. Pin Configuration. Ordering Information HI-201/883. Quad SPST CMOS Analog Switch. FN7990 Rev.0. ATAHEET Quad PT CMO Analog witch The is a monolithic device comprised of four independently selectable PT switchers which feature fast switching speeds (185ns typical) combined with low power dissipation

More information

High Precision 10 V Reference AD587

High Precision 10 V Reference AD587 High Precision V Reference FEATURES Laser trimmed to high accuracy.000 V ±5 mv (L and U grades) Trimmed temperature coefficient 5 ppm/ C max (L and U grades) Noise reduction capability Low quiescent current:

More information

DATASHEET HA-5104/883. Description. Features. Applications. Ordering Information. Pinout. Low Noise, High Performance, Quad Operational Amplifier

DATASHEET HA-5104/883. Description. Features. Applications. Ordering Information. Pinout. Low Noise, High Performance, Quad Operational Amplifier DATASHEET Low Noise, High Performance, Quad Operational Amplifier FN3710 Rev 1.00 Features This Circuit is Processed in Accordance to MILSTD 883 and is Fully Conformant Under the Provisions of Paragraph

More information

High Precision 10 V Reference AD587

High Precision 10 V Reference AD587 High Precision V Reference FEATURES Laser trimmed to high accuracy.000 V ± 5 mv (U grade) Trimmed temperature coefficient 5 ppm/ C maximum (U grade) Noise-reduction capability Low quiescent current: ma

More information

Complete Low Cost 12-Bit D/A Converters ADDAC80/ADDAC85/ADDAC87

Complete Low Cost 12-Bit D/A Converters ADDAC80/ADDAC85/ADDAC87 a FEATURES Single Chip Construction On-Board Output Amplifier Low Power Dissipation: 300 mw Monotonicity Guaranteed over Temperature Guaranteed for Operation with 12 V Supplies Improved Replacement for

More information

DATASHEET EL7240, EL7241. Features. Pinouts. Applications. Ordering Information. Operating Voltage Range. High Speed Coil Drivers

DATASHEET EL7240, EL7241. Features. Pinouts. Applications. Ordering Information. Operating Voltage Range. High Speed Coil Drivers High Speed Coil Drivers OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc DATASHEET FN7284 Rev 0.00 The EL7240/EL7241 high speed

More information

8408 Quad 8-Bit Multiplying CMOS D/A Converter with Memory

8408 Quad 8-Bit Multiplying CMOS D/A Converter with Memory Quad 8-Bit Multiplying CMOS FEATURES: RAD-PAK patented shielding against natural space radiation Total dose hardness: - equal to 100 krad (Si), depending upon orbit and space mission Package: - 28 pin

More information

OBSOLETE. 16-Bit/18-Bit, 16 F S PCM Audio DACs AD1851/AD1861

OBSOLETE. 16-Bit/18-Bit, 16 F S PCM Audio DACs AD1851/AD1861 a FEATURES 0 db SNR Fast Settling Permits 6 Oversampling V Output Optional Trim Allows Super-Linear Performance 5 V Operation 6-Pin Plastic DIP and SOIC Packages Pin-Compatible with AD856 & AD860 Audio

More information

ISL Features. Multi-Channel Buffers Plus V COM Driver. Ordering Information. Applications. Pinout FN Data Sheet December 7, 2005

ISL Features. Multi-Channel Buffers Plus V COM Driver. Ordering Information. Applications. Pinout FN Data Sheet December 7, 2005 Data Sheet FN6118.0 Multi-Channel Buffers Plus V COM Driver The integrates eighteen gamma buffers and a single V COM buffer for use in large panel LCD displays of 10 and greater. Half of the gamma channels

More information

Current Output/Serial Input, 16-Bit DAC AD5543-EP

Current Output/Serial Input, 16-Bit DAC AD5543-EP Data Sheet Current Output/Serial Input, 16-Bit DAC FEATURES FUNCTIONAL BLOCK DIAGRAM 1/+2 LSB DNL ±3 LSB INL Low noise: 12 nv/ Hz Low power: IDD = 1 μa.5 μs settling time 4Q multiplying reference input

More information

Improved Second Source to the EL2020 ADEL2020

Improved Second Source to the EL2020 ADEL2020 Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling

More information