AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS

Size: px
Start display at page:

Download "AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS"

Transcription

1 AUTOMOTIVE CURRENT TRANSDUCER HCF-SN CLIPS Introduction The HCF CLIPS Family is for the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive applications with galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). The HCF CLIPS family gives you the choice of having different current measuring ranges in the same housing. Features Open Loop transducer using the Hall effect Low voltage application Unipolar + 5 V DC power supply Primary current measuring range from 8 A up to 5 A Maximum RMS primary admissible current: defined by busbar to have T < + 5 C Operating temperature range: - 4 C < T < + 5 C Output voltage: full ratiometric (in sensitivity and offset) Compact design for PCB mounting. Principle of HCF CLIPS Family The open loop transducers uses a Hall effect integrated circuit. The magnetic flux density B, contributing to the rise of the Hall voltage, is generated by the primary current to be measured. The current to be measured is supplied by a current source i.e. battery or generator (Fig. ). Within the linear region of the hysteresis cycle, B is proportional to: B ( ) = constant (a) x The Hall voltage is thus expressed by: V H = (R H /d) x I x constant (a) x Except for, all terms of this equation are constant. Therefore: V H = constant (b) x The measurement signal V H amplified to supply the user output voltage or current. Advantages +V c Excellent accuracy Very good linearity Very low thermal offset drift Very low thermal sensitivity drift Wide frequency bandwidth No insertion losses. -V c V Automotive applications Primary current Isolated output voltage Electrical Power Steering Starter Generators Converters... Fig. : Principle of the open loop transducer Page /5

2 HCF-SN CLIPS Dimensions HCF-SN CLIPS family (in mm) Secondary connection Terminals Designations 3 Supply voltage + 5 V DC Ground E to E4 Ground (*) Connection HCF-SN CLIPS Bill of materials Plastic case PBT GF 3 Magnetic core FeNi alloy Pins and primary bus bar Copper alloy tin Mass 6 g plated (lead free) Remarks General tolerance ±. mm V C V OUT > when flows in the direction of the arrow. Electronic schematic +/- Ip Hall ASIC Output amplifier Out +5V C Gnd C3 R C Signal Gnd Power supply decoupling capacitor: C = 47 nf EMC protection capacitor C3 = 4.7 nf Optional: High frequency signal noise filter: R > Ω C = defined according to the system frequency bandwidth Page /5

3 Absolute maximum ratings (not operating) Operating characteristics Parameter Symbol Unit HCF-SN CLIPS Specification Min Typical Max Electrical Data Conditions Primary current, measuring range M A - 4 C < T < 5 C Supply voltage ) V C V C < T < 5 C Output voltage (Analog) V OUT V V OUT = (V C /5) x (.5 +. x I - 4 C < T < 5 C P Sensitivity G T A = 5 C; V C = 5 V Offset voltage V O V C = 5 V; T A = 5 C; = A Current consumption I C ma C < T < 5 C; 4.75 V < V C < 5.5 V Load resistance R L ΚΩ - - Output internal resistance R OUT Ω - - Performance Data () Sensitivity error ε G % -. T A = 5 C, V C = 5 V; Gth =. V/A Electrical offset Magnetic offset Average temperature coefficient of Parameter Symbol Unit Specification Conditions Maximun peak primary current (not operating) max A Defined by busbar to have T 5 C Primary nominal DC or current rms N A Defined by busbar to have T 5 C Maximun supply voltage (not operating) V C max V 7 Secondary maximum admissible power P S max mw 5 Ambient operating temperature T A C -4 < T A < 5 C Ambient storage temperature T S C -4 < T S < 5 C Electrostatic discharge voltage V ESD V Maximum admissible vibration γ m.s - see page 5/5 Rms voltage for AC insulation test 5 Hz, min V d V 5 see page 5/5 Creepage distance dcp mm.67 Clearance dci mm.8 CTI=45 I OE A -.7 ±.5.7 V OE mv -4 ± 5 4 I OM A -.5 ±.5.5 V OM mv -5 ± 3 5 I OE TCI OEAV ma/ C -7 ± 4 7 V OE TCV OEAV mv/ C -.4 V C = 5. V; T A = 5 After excursion to ± ; T A = C < T < 5 C; V C = 5. V Average temperature coefficient of G TCG AV %/ C C < T < 5 C; V C = 5. V Linearity error ε L % -. ; V C = 5. V, T A = 5 C Response time t r µs - di/dt = 5 A/µs; I T = 6 A Frequency bandwidth ) BW khz - -3 db; I T = A rms Output voltage noise peak-peak V no p-p mv - 35 T A = 5 C; Hz < f < MHz Output voltage noise rms V no rms mv - - T A = 5 C; Hz < f < MHz Typical global accuracy (A) C < T < 85 C - 4 C < T < 5 C Notes: ) The output voltage V OUT is fully ratiometric. The offset and sensitivity are dependent on the supply voltage V C relative to the following formula: IP = V OUT VC 5 G V C with G in (V / A) ) Small signal only to avoid excessive heating of the busbar, the magnetic core and the ASIC. Primary current Ip (A) Page 3/5

4 I HCF-SN CLIPS Typical linearity (% of A).%.8%.6%.4%.%.% % -.4% -.6% -.8% -.% Prim ary current Ip (A) Output voltage (V) Primary current Ip (A) C C C Fig. 3: Typical linearity versus primary current at T = 5 C Fig. 4: Typical output voltage versus primary current across temperature Mean relative gain error (%) 3.5% 3.%.5%.%.5%.%.5%.% % Mean relative offset error (mv) % T ( C) -3 Temperature T ( C) Fig. 5: Typical sensitivity error versus temperature Influence of the external magnetic field Test conditions : - transducer sample : HCF-SN CLIPS - diameter of the disturbing conductor : 6 mm - dimension of the primary bus-bar : 6 x x mm - tested at ambient temperature Fig. 6: Typical offset error versus temperature Current levels: CASE CASE CASE 3 CASE 4 I disturbant + A - A + A - A I primary A A + A + A D C B.5 E HCFxxx-SN LEM A I disturbed+ A B C D E F G G G H I J K L F G G G H L -.5 K I disturbed+ - HCFxxx-SN Position case case case3 case4 LEM J Page 4/5

5 HCF-SN CLIPS PERFORMANCES PARAMETERS DEFINITIONS Output noise voltage: The output voltage noise is the result of the noise floor of the Hall elements and the linear I C amplifier gain. Magnetic offset: The magnetic offset is the consequence of an over-current on the primary side. It s defined after an excursion of max. Linearity: The maximum positive or negative discrepancy with a reference straight line V OUT = f ( ). Unit: linearity (%) expressed with full scale of max. V OUT Non linearity example Sensitivity: The Transducer s sensitivity G is the slope of the straight line = f ( ), it must establish the relation: ( ) = V C /5 (G x +.5) (*) (*) For all symetrics transducers. Offset with temperature: The error of the offset in the operating temperature is the variation of the offset in the temperature considered with the initial offset at 5 C. The offset variation I OT is a maximum variation the offset in the temperature range: I OT = I OE max - I OE min The Offset drift TCI OEAV is the I OT value divided by the temperature range. Reference straight line Max linearity error Linearity variation in I N % Sensitivity with temperature: The error of the sensitivity in the operating temperature is the relative variation of sensitivity with the temperature considered with the initial offset at 5 C. The sensitivity variation G T is the maximum variation (in ppm or %) of the sensitivity in the temperature range: G T = (Sensitivity max - Sensitivity min) / Sensitivity at 5 C. The sensitivity drift TCG AV is the G T value divided by the temperature range. Response time (delay time) t r : The time between the primary current signal and the output signal reach at 9 % of its final value 9 % I [A] t r I T I S Offset = A: Is the output voltage when the primary current is null. The ideal value of V O is V C / at V C = 5 V. So, the difference of V O -V C / is called the total offset voltage error. This offset error can be attributed to the electrical offset (due to the resolution of the ASIC quiescent voltage trimming), the magnetic offset, the thermal drift and the thermal hysteresis. Environmental test specifications Name Standard Conditions Low T storage IEC 668 Part - Thermal shocks IEC 668 Part -4 Low T operation at min supply voltage Hight T operation at max supply voltage IEC 668 Part - IEC 668 Part - T - 4 C / H not connected T - 3 C to C / cycles not connected T - 4 C / H supply voltage = 4.75 V T 5 C / H supply voltage = 5.5 V t [µs] Temperature humidity bias IEC 668 Part -3 T 9 C / 95 % RH/ H supply voltage = 5.5 V Typical: Theorical value or usual accuracy recorded during the production. Pressure cooker Mechanical Tests Vibration IEC T 5 C / % RH, P.78 Mpa/ H supply voltage = 5 V Room T, acceleration m/s, frequency to 5 Hz/96 H each axis Drop test IEC 668 Part -9 Heigh 75 mm concret floor each directions EMC Test Electrostatic discharge JESD-A4-B Applied voltage = ± kv pin to pin number of discharge = Page 5/5

HC2F100-SN CLIPS AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS. Datasheet

HC2F100-SN CLIPS AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS. Datasheet AUTOMOTIVE CURRENT TRANSDUCER Datasheet 071113/1 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. Page 1/ 6 www.lem.com Introduction

More information

AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S

AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and

More information

AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S

AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and

More information

AUTOMOTIVE CURRENT TRANSDUCER HC6H1000-S

AUTOMOTIVE CURRENT TRANSDUCER HC6H1000-S AUTOMOTIVE CURRENT TRANSDUCER HC6H1000-S 18198151434 Page 1/ 5 HC6H1000-S Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in

More information

AUTOMOTIVE CURRENT SENSOR HC6H300-S

AUTOMOTIVE CURRENT SENSOR HC6H300-S AUTOMOTIVE CURRENT SENSOR HC6H300-S Page 1/ 5 Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive

More information

AUTOMOTIVE CURRENT SENSOR HC6H500-S. Datasheet

AUTOMOTIVE CURRENT SENSOR HC6H500-S. Datasheet AUTOMOTIVE CURRENT SENSOR HC6H500-S Datasheet Page 1/ 5 Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and low

More information

AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S02

AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S02 AUTOMOTIVE CURRENT TRANSDUCER Introduction The HAH3DR family, a tri-phase tranducer is for the electronic measurement of DC, AC or pulsed s in high power automotive applications with galvanic isolation

More information

AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S00

AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S00 AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S00 Introduction The HAH3DR family, a tri-phase tranducer is for the electronic measurement of DC, AC or pulsed s in high power automotive applications with galvanic

More information

AUTOMOTIVE CURRENT TRANSDUCER HAH1DR 300-S

AUTOMOTIVE CURRENT TRANSDUCER HAH1DR 300-S AUTOMOTIVE CURRENT TRANSDUCER Introduction The HAH1DR family is for the electronic measurement of DC, AC or pulsed currents in high power automotive applications with galvanic isolation between the primary

More information

AUTOMOTIVE CURRENT TRANSDUCER DHAB S/15

AUTOMOTIVE CURRENT TRANSDUCER DHAB S/15 AUTOMOTIVE CURRENT TRANSDUCER Introduction The DHAB family is best suited for DC, AC, or pulsed currents measurement in high power and low voltage automotive applications. Its contains galvanic isolation

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH1DRW 300-S

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH1DRW 300-S AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY Introduction The HAH1DRW family is for the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive applications with

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH1DR 200-S

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH1DR 200-S AUTOMOTIE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAHDR 2-S Introduction The HAHDR family is for the electronic measurement of DC, AC or pulsed currents in high power automotive applications with galvanic

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 1100-S07

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 1100-S07 AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY Introduction The HAH3DR-S07 family is a tri-phase transducer for DC, AC, or pulsed currents measurement in automotive applications. It offers a galvanic

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/124

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/124 AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/124 Picture of product with pencil Introduction The DHAB family is best suited for DC, AC, or pulsed currents measurement in high power and low

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 800-S03/SP2

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 800-S03/SP2 AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY Introduction The HAH3DR-S03 family is a tri-phase transducer for DC, AC, or pulsed currents measurement in high power and low voltage automotive applications.

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/157

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/157 AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY DHAB S/157 Introduction The DHAB family is best suited for DC, AC, or pulsed currents measurement in high power and low voltage automotive applications.

More information

AUTOMOTIVE CURRENT SENSOR DHAB S/18. Datasheet

AUTOMOTIVE CURRENT SENSOR DHAB S/18. Datasheet AUTOMOTIVE CURRENT SENSOR DHAB S/18 Datasheet 070720/1 Page 1/6 Introduction The DHAB family is best suited for DC, AC or pulse current measurement in high power and low voltage automotive applications.

More information

AUTOMOTIVE CURRENT SENSOR DHAB S/25. Datasheet

AUTOMOTIVE CURRENT SENSOR DHAB S/25. Datasheet AUTOMOTIVE CURRENT SENSOR DHAB S/25 Datasheet Page 1/6 Introduction The DHAB family is best suited for DC, AC or pulse current measurement in high power and low voltage automotive applications. It s contains

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 800-S0C

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 800-S0C AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 800-S0C Introduction The HAH3DR-S0C family is a dual-phase transducer for DC, AC, or pulsed currents measurement in high power and low voltage

More information

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HSW S01

AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HSW S01 AUTOMOTIE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HSW S01 Introduction The HSW family is best suited for DC and AC currents measurement in high power and high voltage automotive applications. It features

More information

AUTOMOTIVE CURRENT TRANSDUCERS OPEN LOOP TECHNOLOGY

AUTOMOTIVE CURRENT TRANSDUCERS OPEN LOOP TECHNOLOGY AUTOMOTIVE CURRENT TRANSDUCERS OPEN LOOP TECHNOLOGY HSNBV 100-(*)X00; HSNBV 200-X00; HSNBV 300-X00; HSNBV 400-X00; HSNBV 500-X00; HSNBV 600-X00; HSNBV 700-X00; HSNBV 800-X00; HSNBV 900-X00; * Introduction

More information

High Performance Current Transducer IT 200-S ULTRASTAB = A. ε L

High Performance Current Transducer IT 200-S ULTRASTAB = A. ε L High Performance Current Transducer IT 200-S ULTRASTAB For the electronic measurement of currents: DC, AC, pulsed..., with galvanic isolation between the primary circuit and the secondary circuit. I PM

More information

Current Transducer CTSR 1-P = 1A

Current Transducer CTSR 1-P = 1A Current Transducer CTSR 1-P I PRN = 1A For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary (high power) and the secondary circuit (electronic circuit).

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 700-SB ULTRASTAB I PM = 700 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features ± 10 V voltage output

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Current Transducer CASR series I PN = 6, 5, 25, 5 A Ref: CASR 6-NP, CASR 5-NP, CASR 25-NP, CASR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 700-S ULTRASTAB I PM = 700 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)

More information

High Performance Current Transducer ITL 900-T = A

High Performance Current Transducer ITL 900-T = A High Performance Current Transducer ITL 900-T For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I PM = 0... 900 A Electrical

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer ITN 1000-S ULTRASTAB I PM = 1000 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)

More information

Ref: HLSR 10-P/SP3, HLSR 20-P/SP3, HLSR 40-P/SP3, HLSR 50-P/SP3

Ref: HLSR 10-P/SP3, HLSR 20-P/SP3, HLSR 40-P/SP3, HLSR 50-P/SP3 Current Transducer HLSR-P/SP3 series N = 10... 50 A Ref: HLSR 10-P/SP3, HLSR 20-P/SP3, HLSR 40-P/SP3, HLSR 50-P/SP3 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation

More information

HO 50-S/SP30, HO 100-S/SP30, HO 150-S/SP30, HO 200-S/SP30, HO 250-S/SP30 and HO 200-S/SP31

HO 50-S/SP30, HO 100-S/SP30, HO 150-S/SP30, HO 200-S/SP30, HO 250-S/SP30 and HO 200-S/SP31 Current Transducer HO-S/SP3 series Ref: I PN = 5,, 15, 2, 25 A HO 5-S/SP3, HO -S/SP3, HO 15-S/SP3, HO 2-S/SP3, HO 25-S/SP3 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation

More information

Ref: HO 50-S/SP33, HO 100-S/SP33, HO 150-S/SP33, HO 200-S/SP33, HO 250-S/SP33

Ref: HO 50-S/SP33, HO 100-S/SP33, HO 150-S/SP33, HO 200-S/SP33, HO 250-S/SP33 Current Transducer HO-S/SP33 series I PN = 50, 100, 150, 200, 250 A Ref: HO 50-S/SP33, HO 100-S/SP33, HO 150-S/SP33, HO 200-S/SP33, HO 250-S/SP33 For the electronic measurement of current: DC, AC, pulsed...,

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer IN 1000-S N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)

More information

Ref: HLSR 10-SM, HLSR 16-SM, HLSR 20-SM, HLSR 32-SM, HLSR 40-SM, HLSR 50-SM

Ref: HLSR 10-SM, HLSR 16-SM, HLSR 20-SM, HLSR 32-SM, HLSR 40-SM, HLSR 50-SM Current Transducer HLSR-SM series N = 1... 5 A Ref: HLSR 1-SM, HLSR 16-SM, HLSR 2-SM, HLSR 32-SM, HLSR 4-SM, HLSR 5-SM For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation

More information

AUTOMOTIVE CURRENT TRANSDUCER HAB 60-S/SP5

AUTOMOTIVE CURRENT TRANSDUCER HAB 60-S/SP5 AUOMOIVE CURREN RANSDUCER HAB 60-S/SP5 Introduction he HAB Family is best suited for DC, AC or pulsed currents measurement in high power and low voltage automotive applications. It s contains galvanic

More information

I PN. Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S

I PN. Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S Current Transducer HO-S series I PN = 50, 100, 150, 200, 240, 250 A Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S For the electronic measurement of current: DC, AC, pulsed..., with galvanic

More information

Ref: HLSR 10-SM/SP33, HLSR 20-SM/SP33, HLSR 32-SM/SP33, HLSR 40-P/SP33, HLSR 50-SM/SP33

Ref: HLSR 10-SM/SP33, HLSR 20-SM/SP33, HLSR 32-SM/SP33, HLSR 40-P/SP33, HLSR 50-SM/SP33 Current Transducer HLSR-SM/SP33 series I PN = 10... 50 A Ref: HLSR 10-SM/SP33, HLSR 20-SM/SP33, HLSR 32-SM/SP33, HLSR 40-P/SP33, HLSR 50-SM/SP33 For the electronic measurement of current: DC, AC, pulsed...,

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 605-S ULTRASTAB I PN = 600 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 200-S ULTRASTAB I PM = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer IN 1000-S I P N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer CAS 25-NP/SP2 N = 25 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer CKSR series N = 6, 5, 25, 5 A Ref: CKSR 6-NP, CKSR 5-NP, CKSR 25-NP, CKSR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary

More information

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.

For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications. Current Transducer IT 205-S ULTRASTAB I PN = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer N = 6, 15, 25, 5 A Ref: LESR 6-NP, LESR 15-NP, LESR 25-NP, LESR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the

More information

Current Sensor: ACS750xCA-100

Current Sensor: ACS750xCA-100 5 Pin 1: V CC Pin 2: Gnd Pin 3: Output 4 1 2 3 Terminal 4: I p+ Terminal 5: I p- ABSOLUTE MAXIMUM RATINGS Operating Temperature S... 2 to +85ºC E... 4 to +85ºC Supply Voltage, Vcc...16 V Output Voltage...16

More information

Current transducer FHS 40-P/SP600

Current transducer FHS 40-P/SP600 Current transducer I PM = 0-100 A Minisens transducer The Minisens transducer is an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle. It is suitable for

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer HO-NSM/SP33 series N = 8, 15, 25 A Ref: HO 8-NSM/SP33, HO 15-NSM/SP33, HO 25-NSM/SP33 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer HO-NP series I PN = 4, 6, 12, 15 Ref: HO 4-NP, HO 6-NP, HO 12-NP, HO 15-NP For the electronic measurement of current: DC, C, pulsed..., with galvanic separation between the primary and

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer LESR series N = 6, 15, 25, 5 A Ref: LESR 6-NP, LESR 15-NP, LESR 25-NP, LESR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer HO-NSM- SERIES I PN = 8, 15, 25 A Ref: HO 8-NSM-, HO 15-NSM-, HO 25-NSM- For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. Current Transducer CTSR 0.6-TP/SP2 I PRN = 600 ma For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. Features

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 510-S I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 1010-S/SPA2 I PN = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 210-S/SP3 I PN = 100 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer ITL 4000-S I PN = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 2010-S I PN = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

Voltage transducer DVL 50

Voltage transducer DVL 50 Voltage transducer DVL 5 V PN = 5 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated measurement

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer LF 510-S/SP13 I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Voltage transducer DVL 15 V PN = 15 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated

More information

Current transducer FHS 40-P/SP600

Current transducer FHS 40-P/SP600 Current transducer I PM = 0-100 A Minisens transducer The Minisens transducer is an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle. It is suitable for

More information

AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX

AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX AUTOMOTIVE CURRENT TRANSDUCER FLUXGATE TECHNOLOGY CAB 300-C/SP3-XXX Introduction The CAB family is for battery monitoring applications where high accuracy and very low offset are required. Features Transducer

More information

Current Sensor: ACS750xCA-050

Current Sensor: ACS750xCA-050 5 4 The Allegro ACS75x family of current sensors provides economical and precise solutions for current sensing in industrial, automotive, commercial, and communications systems. The device package allows

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer LF 2010-S/SPA7 I P N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer ITL 4000-S I P N = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and secondary circuit. Current Transducer LF 510-S I P N = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer LF 2010-S/SPA0 I P N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Voltage transducer V PN = 1 V Ref: DV 1/SP For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated

More information

= 1000 V. Voltage transducer DVC 1000-P V P N

= 1000 V. Voltage transducer DVC 1000-P V P N Voltage transducer DVC 1-P V P N = 1 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer LF 21-S/SPA2 I P N = 2 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

Current Sensor: ACS752SCA-050

Current Sensor: ACS752SCA-050 5 4 The Allegro ACS75x family of current sensors provides economical and precise solutions for current sensing in industrial, automotive, commercial, and communications systems. The device package allows

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Voltage transducer DV V PN = V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Applications Bipolar and insulated

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current transducer ITC 2000-S/SP2 N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

Current Sensor: ACS755SCB-200

Current Sensor: ACS755SCB-200 Pin 1: VCC Pin 2: GND Pin 3: VOUT Terminal 4: IP+ Terminal 5: IP AB SO LUTE MAX I MUM RAT INGS Supply Voltage, V CC...16 V Reverse Supply Voltage, V RCC... 16 V Output Voltage, V OUT...16 V Reverse Output

More information

DS2000UBLA-10V. Features. Applications: 20 ppm linearity. MPS for particles accelerators. 15 ppm offset. Gradient amplifiers for MRI devices

DS2000UBLA-10V. Features. Applications: 20 ppm linearity. MPS for particles accelerators. 15 ppm offset. Gradient amplifiers for MRI devices Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 2000A Features 20 ppm linearity 15 ppm offset 10V

More information

Current Sensor: ACS754xCB-100

Current Sensor: ACS754xCB-100 Pin 1: VCC Pin 2: GND Pin 3: VOUT 5 4 1 2 3 Package CB-PFF 5 1 2 3 Package CB-PSF 1 2 3 5 4 Package CB-PSS 4 Terminal 4: IP+ Terminal 5: IP AB SO LUTE MAX I MUM RAT INGS Supply Voltage, V CC...16 V Output

More information

DS400ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1.5 ppm. MPS for particles accelerators

DS400ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1.5 ppm. MPS for particles accelerators Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 600A Features Linearity error maximum 1.5 ppm Fluxgate,

More information

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Current Transducer LF 1010-S/SPA5 I P N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and

More information

DQ600ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1 ppm. MPS for particles accelerators

DQ600ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1 ppm. MPS for particles accelerators Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A Features Linearity error maximum 1 ppm Fluxgate,

More information

Unipolar voltage - Current output 4-20 ma Ref: DVL 50-UI, DVL 150-UI, DVL 250-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI

Unipolar voltage - Current output 4-20 ma Ref: DVL 50-UI, DVL 150-UI, DVL 250-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI Current Transducer DVL-UI series V PN = 50... 1500 V Unipolar voltage - Current output 4-0 ma Ref: DVL 50-UI, DVL 150-UI, DVL 50-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI For the electronic

More information

DL2000ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.

DL2000ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators. DL000ID Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 6 ppm offset

More information

I PM. Current Transducer ITZ 5000-SB FLEX ULTRASTAB = 5000 A

I PM. Current Transducer ITZ 5000-SB FLEX ULTRASTAB = 5000 A urrent Transducer ITZ 5000-SB FLEX ULTRASTAB I PM = 5000 A For ultra-high precision measurement of current: D, A, pulsed..., with galvanic separation between primary and secondary. Separate magnetic head

More information

= 600 V. Voltage transducer DVM 600 V PN

= 600 V. Voltage transducer DVM 600 V PN Voltage transducer DVM 6 V PN = 6 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

DS200ID-CD100. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 2 ppm. MPS for particles accelerators

DS200ID-CD100. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 2 ppm. MPS for particles accelerators Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 370A Features Linearity error maximum 2 ppm 100

More information

DS2000ICLA. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.

DS2000ICLA. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators. Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 0 ppm offset Current

More information

Current Sensor: ACS754SCB-200

Current Sensor: ACS754SCB-200 Pin 1: VCC Pin 2: GND Pin 3: VOUT Terminal 4: IP+ Terminal 5: IP AB SO LUTE MAX I MUM RAT INGS Supply Voltage, V CC...16 V Reverse Supply Voltage, V RCC... 16 V Output Voltage, V OUT...16 V Reverse Output

More information

V P N. Voltage transducer DVM 2000-B = 2000 V

V P N. Voltage transducer DVM 2000-B = 2000 V Voltage transducer DVM 2-B V P N = 2 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

DM1200ID. Specification highlights Symbol Unit Min Typ Max. Applications: Features. Power measurement and power analysis

DM1200ID. Specification highlights Symbol Unit Min Typ Max. Applications: Features. Power measurement and power analysis Ultra-stable, high precision (ppm class) fluxgate technology DM Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1500A Features Ø45mm aperture enabling large isolated

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Voltage transducer V PN = 4 V Ref: DV 4/SP4 For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated

More information

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017

I P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017 Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175, ART-B22-D300 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and

More information

I P. /dt. di p V S+ Applications. Standards. 1) IEC ed1.0: 2007; IEC : ed1.0: 2012

I P. /dt. di p V S+ Applications. Standards. 1) IEC ed1.0: 2007; IEC : ed1.0: 2012 Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and the secondary

More information

Limited Availability Product

Limited Availability Product Limited Availability Product This device is in production, but is limited to existing customers. Contact factory for additional information. Date of status change: November 2, 2009 Recommended Substitutions:

More information

Typical Application VCC IP+ ACS755 GND C F 3 R F

Typical Application VCC IP+ ACS755 GND C F 3 R F Features and Benefits Monolithic Hall IC for high reliability Single +5 V supply 3 kv RMS isolation voltage between terminals 4/5 and pins 1/2/3 for up to 1 minute 35 khz bandwidth Automotive temperature

More information

Typical Application C BYP C F 3 R F

Typical Application C BYP C F 3 R F Features and Benefits Monolithic Hall IC for high reliability Single +5 V supply 3 kv RMS isolation voltage between terminals 4/5 and pins 1/2/3 for up to 1 minute 35 khz bandwidth Automotive temperature

More information

DS10000ULFS-10V/10kA

DS10000ULFS-10V/10kA Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 11kA Features Linearity error maximum +/- 7ppm

More information

SPECIFICATION Item no.: T60404-N4646-X764

SPECIFICATION Item no.: T60404-N4646-X764 Customer: Standard type Customers Part no: Page 1 of 4 Description Closed loop (compensation) Current Sensor with magnetic field probe Printed circuit board mounting Casing and materials UL-listed Electrical

More information

V P N. Voltage transducer DVL 1000 = 1000 V

V P N. Voltage transducer DVL 1000 = 1000 V Voltage transducer DVL 1 V P N = 1 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

Last Time Buy. Deadline for receipt of LAST TIME BUY orders: May 1, 2008.

Last Time Buy. Deadline for receipt of LAST TIME BUY orders: May 1, 2008. Last Time Buy These parts are in production but have been determined to be LAST TIME BUY. This classification indicates that the product is obsolete and notice has been given. Sale of this device is currently

More information

Discontinued Product

Discontinued Product Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available. Date of status change: May 4, 2009 Recommended

More information

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.

For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Voltage transducer DV 64 V P N = 64 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated

More information

IMC-Hall Current Sensor

IMC-Hall Current Sensor CSA-1V IMC-Hall Current Sensor Features: IMC-Hall technology - Very high sensitivity due to integrated magnetic concentrator Sensitive to a magnetic field parallel to the chip surface Linear output voltage

More information

V P N. Voltage transducer DVM 4200 = 4200 V

V P N. Voltage transducer DVM 4200 = 4200 V Voltage transducer DVM 42 N = 42 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated measurement

More information