PART GND MAX5461 MAX5462 MAX MAX5468 SOT23, SC70 MAX5467 SOT23, SC70. Maxim Integrated Products 1

Transcription

1 9-956; Rev 3; /5 32-Tap FleaPoT, 2-ire Digital General Description The linear-taper digital potentiometers perform the same function as a mechanical potentiometer or a variable resistor. These devices consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a 2-wire serial interface. The MAX5462/MAX5465/MAX5468 are configured as potentiometers. The rest of the devices in this family are configured as variable resistors. See Pin Configurations for part functionality. Three resistance values are available: kω (MAX5466/ /MAX5468), 5kΩ (MAX5463/MAX5464/ MAX5465), and kω (MAX546//MAX5462). The MAX546 MAX5465 (kω and 5kΩ) are available in space-saving 5-pin and 6-pin SC7 packages. The MAX5466//MAX5468 (kω) are available in 5-pin and 6-pin SOT23 packages. Applications LCD Screen Adjustment Volume Control Mechanical Potentiometer Replacement Gain Adjustment Line Impedance Matching FleaPoT is a trademark of Maxim Integrated Products Inc. Functional Diagram appears at end of data sheet. Features Miniature SC7 and SOT23 Packages.3µA Ultra-Low Supply Current +2.7V to +5.5V Single-Supply Operation Glitchless Switching Between Resistor Taps Power-On Reset to Midscale 2-ire Up/Down Serial Interface kω, 5kΩ, and kω Resistance Values PART PIN- PACKAGE Ordering Information TOP MARK R (kω) PKG CODE MAX546EXK 5 SC7 ACA X5- EXT 6 SC7 AAP X6S- MAX5462EXT 6 SC7 AAQ X6S- MAX5463EXK 5 SC7 ACB 5 X5- MAX5464EXT 6 SC7 AAR 5 X6S- MAX5465EXT 6 SC7 AAS 5 X6S- MAX5466EUK 5 SOT23 ADQQ U5- EUT 6 SOT23 AARH U6- MAX5468EUT 6 SOT23 AARI U6- Note: All devices operate over the -4 C to +85 C temperature range. Pin Configurations TOP VIE V DD 5 H V DD 6 H V DD 6 H GND 2 GND 2 5 L GND MAX546 MAX MAX MAX MAX5462 MAX MAX5468 SOT23, SC7 SOT23, SC7 SOT23, SC7 Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at , or visit Maxim s website at

2 ABSOLUTE MAXIMUM RATINGS V DD to GND...-.3V to +6V All Other Pins to GND...-.3V to (V DD +.3)V Input and Output Latch-Up Immunity...±2mA Maximum Continuous Current into H, L, and MAX546//MAX5462 (kω)...±.6ma MAX5463/MAX5464/MAX5465 (5kΩ)...±.3mA MAX5466//MAX5468 (kω)...±.3ma Continuous Power Dissipation (T A = +7 C) 5-pin SC7 (derate 3.m/ C above T A = +7 C)...247m 5-pin SOT23 (derate 7.m/ C above T A = +7 C)...57m 6-pin SC7 (derate 3.m/ C above T A = +7 C)...245m 6-pin SOT23 (derate 8.7m/ C above T A = +7 C) m Operating Temperature Range...-4 C to +85 C Junction Temperature...+5 C Storage Temperature Range C to +5 C Soldering Temperature (soldering, s)...+3 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTI (V DD = +2.7V to +5.5V, V H = V DD, V L =, T A = -4 C to +85 C. Typical values are at V DD = +2.7V, T A = +25 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC PERFORMANCE Resolution 32 Taps End-to-End Resistance MAX546//MAX MAX5463/MAX5464/MAX MAX5466//MAX End-to-End Resistance Tempco TC R 35 ppm/ C Ratiometric Resistance Tempco 5 ppm/ C Integral Nonlinearity INL ±.5 ± LSB Differential Nonlinearity DNL ± LSB Full-Scale Error ±. LSB Zero-Scale Error LSB MAX5462/MAX iper Resistance R MAX kω Ω DIGITAL INPUTS Input High Voltage V IH.7 x V DD V Input Low Voltage V IL.3 x V DD V TIMING CHARACTERISTI (Figures, 2) Mode to Setup t CU 25 ns to Step Setup t CI 5 ns to Step Hold t IC 25 ns Step Low Period t IL 25 ns Step High Period t IH 25 ns Up/Down Toggle Rate (Note ) f TOGGLE MHz kω var i ab l e r esi stor confi g ur ati on, C L = p F Output Settling Time (Note 2) t SETTLE kω p otenti om eter confi g ur ati on, C L = p F.25 µs 2

3 ELECTRICAL CHARACTERISTI (continued) (V DD = +2.7V to +5.5V, V H = V DD, V L =, T A = -4 C to +85 C. Typical values are at V DD = +2.7V, T A = +25 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS POER SUPPLIES Supply Voltage V DD V Active Supply Current (Note 3) I DD 25 µa Standby Supply Current (Note 4) I SD V DD = +5V.3 µa Note : Up/Down Toggle Rate: ftoggle = tsettle Note 2: Typical settling times are dependent on end-to-end resistance. Note 3: Supply current taken while changing wiper tap, f TOGGLE = MHz. Note 4: Supply current taken while wiper position is fixed. (T A = +25 C, unless otherwise noted.) Typical Operating Characteristics IPER RESISTANCE (Ω) RESISTANCE (kω) IPER RESISTANCE vs. IPER VOLTAGE (MAX546 MAX5465) V DD = +2.7V V DD = +5V IPER VOLTAGE (V) -TO-L RESISTANCE vs. TAP POSITION kω 5kΩ kω TAP POSITION MAX546 toc MAX546 toc4 IPER RESISTANCE (Ω) CURRENT (µa) IPER RESISTANCE vs. IPER VOLTAGE (MAX5466//MAX5468) V DD = +2.7V V DD = +5V IPER VOLTAGE (V) SUPPLY CURRENT vs. TEMPERATURE V DD = +2.7V TEMPERATURE ( C) V DD = +5V MAX546 toc2 MAX546 toc5 END-TO-END RESISTANCE % CHNAGE V/div OUTPUT mv/div END-TO-END RESISTANCE % CHANGE vs. TEMPERATURE kω 5kΩ, kω TEMPERATURE ( C) TAP-TO-TAP SITCHING TRANSIENT (MAX546) 2ns/div MAX546 toc3 MAX546 toc6 3

4 (T A = +25 C, unless otherwise noted.) R-DNL (LSB) R-INL LSB R-DNL ERROR vs. INPUT CODE (kω) R-INL ERROR vs. INPUT CODE (5kΩ) MAX546 toc7 MAX546 toc R-INL (LSB) R-DNL LSB Typical Operating Characteristics (continued) R-INL ERROR vs. INPUT CODE (kω) R-DNL ERROR vs. INPUT CODE (kω) MAX546 toc8 MAX546 toc R-DNL (LSB) R-INL (LSB) R-DNL ERROR vs. INPUT CODE (5kΩ) R-INL ERROR vs. INPUT CODE (kω) MAX546 toc9 MAX546 toc Pin Description MAX546 MAX5463 MAX5466 PIN MAX5464 MAX5462 MAX5465 MAX5468 NAME V DD Power Supply GND Ground FUNCTION Up/Down Control Input. ith low, a low-to-high transition increments or decrements the wiper position. Chip Select Input. A high-to-low transition determines the mode: increment if is high, or decrement if is low H High Terminal of Resistor 5 L Low Terminal of Resistor 5 iper Terminal of Resistor 4

5 Detailed Description The consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a 2-wire serial interface. Three resistance values are available: kω (MAX5466// MAX5468), 5kΩ (MAX5463/MAX5464/MAX5465), and kω (MAX546//MAX5462). The MAX5462/MAX5465/MAX5468 are designed to operate as potentiometers. In this configuration, the low terminal of the resistor array is connected to ground (pin 2). The /MAX5464/ perform as variable resistors. In these devices, the wiper terminal and high terminal of the resistor array are connected at pin 5. The MAX546/MAX5463/MAX5466 are similar variable resistors, except the low terminal is connected to ground (pin 2). Digital Interface Operation The have two modes of operation when the serial interface is active: increment and decrement mode. The serial interface is only active when is low. The and inputs control the position of the wiper along the resistor array. hen transitions from high to low, the part will go into increment mode if is high, and into decrement mode if is low. Once the mode is set, the device will remain in that mode until goes high again. A low-to-high transition at the pin will increment or decrement the wiper position depending on the current mode (Figures and 2). hen the input transitions to high (serial interface inactive), the value of the counter is stored and the wiper position is maintained. Note that when the wiper reaches the maximum (or minimum) tap position, the wiper will not wrap around to the minimum (or maximum) position. t CU t IC t IL t CI t IH t SETTLE t SETTLE NOTE: "" IS NOT A DIGITAL SIGNAL. IT REPRESENTS IPER TRANSITIONS. Figure. Serial Interface Timing Diagram, Increment Mode t CU t IH t IC t IL t CI t SETTLE t SETTLE NOTE: "" IS NOT A DIGITAL SIGNAL. IT REPRESENTS IPER TRANSITIONS. Figure 2. Serial Interface Timing Diagram, Decrement Mode 5

6 Power-On Reset All parts in this family feature power-on reset (POR) circuitry that sets the wiper position to midscale at powerup. By default, the chip is in the increment mode. Applications Information The are intended for circuits requiring digitally controlled adjustable resistance, such as LCD contrast control, where voltage biasing adjusts the display contrast. Controlling a Switch-Mode LCD Bias Generator Figure 3 shows an application where the variable resistor is used with a MAX77 to make an adjustable positive LCD-bias circuit. The output of the MAX77 is a positive voltage that is digitally controlled through the /MAX5464/. Similarly, Figure 4 shows the application of the variable resistor in a digitally controlled negative LCD-bias circuit along with the MAX774/MAX775/MAX776. Alternative Positive LCD Bias Control Alternatively, use an op amp to provide buffering and gain to the output of the MAX5462/MAX5465/MAX5468. Connect the mechanical potentiometer to the positive input of a noninverting op amp (Figure 5) to select a portion of the input signal by digitally controlling the wiper terminal. Figure 6 shows a similar circuit for the /MAX5464/. Adjustable Gain Figure 7 shows how to use the variable resistor to digitally adjust the gain of a noninverting op amp configuration. Connect the /MAX5464/ in series with a resistor to ground to form the adjustable gain control of a noninverting amplifier. The MAX546 MAX5468 have a low 5ppm/ C ratiometric tempco that allows for a very stable adjustable gain configuration over temperature. V IN = 5V C 68µF C3.µF C2.µF 2 V+ REF SHDN AGND MAX77 GND 7 EXT FB 8 3 MAX5464 L 22µH D N C4 N 3µF MTD2N3HDL R SENSE 4mΩ R R VAR R2 C5 V OUT = 2V AT.5A V IN C 5µF C2.µF R2 MAX5464 R 3 2 R VAR 4 C3.µF OUT V+ SHDN FB REF MAX774 MAX775 MAX776 GND 8 EXT L 22µH R3.7Ω Q Si9435 P N5822/ MBR34 C4* V OUT V REF =.5V V OUT(MAX) R2 = + V REF R V OUT(MIN) R2 = V REF ( R + R VAR(MAX) ) + * MAX774 = 33µF, V MAX775/MAX776 = 2µF, 2V V OUT(MAX) R2 V OUT(MIN) R2 =, = V REF R V REF R + R VAR V REF - V FB 5µA (FOR 2% GAIN-SETTING ACCURACY) R + R VAR Figure 3. Adjustable Positive LCD Bias Figure 4. Adjustable Negative LCD Bias 6

7 +5V H L MAX5462 MAX5465 MAX5468 Figure 5. Positive LCD Bias Control 3V V OUT MAX V Figure 6. Positive LCD Bias Control H L 3V V OUT V CC V CC V IN V IN V OUT V OUT H L MAX5464 L MAX5462 MAX5465 MAX5468 H a) b) Figure 7. Adjustable Gain Circuit 7

8 V DD GND UP/DN COUNTER TRANSISTOR COUNT: 792 Functional Diagram 32-POSITION DECODER H L Chip Information 8

9 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to SC7, 5L.EPS PACKAGE OUTLINE, 5L SC C SOT-23 5L.EPS PACKAGE OUTLINE, SOT-23, 5L 2-57 E 9

10 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to 6LSOT.EPS PACKAGE OUTLINE, SOT 6L BODY 2-58 G SC7, 6L.EPS PACKAGE OUTLINE, 6L SC C Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 2 San Gabriel Drive, Sunnyvale, CA Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.