Design of CMOS Instrumentation Amplifier

Size: px
Start display at page:

Download "Design of CMOS Instrumentation Amplifier"

Transcription

1 Available online at Procedia Engineering 29 (2012) International Workshop on Information and Electronics Engineering (IWIEE) Design of CMOS Instrumentation Amplifier M.Y. Ren a *, C.X. Zhang a, D.S. Sun b a School of Softwares, Harbin University of Science and Technology, Harbin , China b Computer Center, Harbin University of Science and Technology, Harbin , China Abstract A low power CMOS instrumentation amplifier used for biomedical applications is presented in this paper. It consists of a low power operational amplifier with CMFC structure. By analysis and optimization of the parasitic effects and parameters, instrumentation amplifier has better performance in every aspect. This simulation result shows that, in the case of guaranteed bandwidth, the amplifier can suppress flicker noise interference effectively. The instrumentation amplifier designed in 0.5μm CMOS technology with 3.3V power supply shows a dynamic range of 70.1dB and 23.48ns settling time within 0.05% accuracy. The main amplifier dissipates 10.5mW power. It also includes a bias circuit that dissipates 2.2mW power Published by Elsevier Ltd. Selection and/or peer-review under responsibility of Harbin University of Science and Technology Open access under CC BY-NC-ND license. Keywords: CMOS integrated circuits,instrumentation amplifier, CMFC 1. Introduction Instrumentation amplifiers are very important circuits in many sensor readout systems where there is a need to amplify small differential signals in the presence of large common-mode interference. Application examples include automotive transducers [1], industrial process control [2] [4], linear position sensing [5], and biopotential acquisition systems [6] [11]. In this paper, a new low power instrumentation amplifier with CMFC op-amp is proposed. The paper is organized as follows. In section II, principle of instrumentation amplifier is described. Sections III describe the architecture and the simulation of the proposed CMFC op-amp. Sections IV describe the * Mingyuan Ren. Tel.: ; fax: address: rmy2000@126.com Published by Elsevier Ltd. Open access under CC BY-NC-ND license. doi: /j.proeng

2 4036 M.Y. Ren et al. / Procedia Engineering 29 (2012) simulation of the proposed instrumentation amplifier. Conclusions are given in sections V. 2. Principle of Instrumentation Amplifier An instrumentation amplifier is one that is used in electronic measuring instruments or in electronic systems in which the highest precision is required. A popular instrumentation amplifier is shown in Fig. 1. It can be built from three op amp integrated circuits but more often the three amplifiers are manufactured already connected on the same chip. As a black box the instrumentation amplifier, or in amp, has the same input and output terminals as a single op amp, but its performance is superior. R = R = R = R, the signal transfer function can be simplified to When A D VOU T R2+ R3 = = (1 + ) V V R1 IN + IN where R2 and R3 is generally set to the same value. Ideally, by simply adjusting the value of R1, the entire gain of the circuit can be adjusted to any value. (1) V IN+ OP1 R 4 R 5 R 1 R 2 R 3 OP3 V OUT V IN- OP2 R 6 R 7 Fig.1 A standard type of instrumentation amplifier comprises three op amps To calculate the common mode gain, we assume the input common-mode voltage is VCM. V = V = V (2) IN + IN CM Therefore, no voltage drop across R1, OP1 and OP2 output voltage is equal to VCM. If we assume OP1 OP2 and OP3 is the ideal op amp, the amp's common-mode rejection ratio is A D CMRR( db) = 20log AC Gain = 20log R + R R R R R + R R (3)

3 M.Y. Ren et al. / Procedia Engineering 29 (2012) where amp's common-mode rejection ratio mainly is decided by matching of several resistance. The resistance of the relative accuracy can very high through the layout of symmetry techniques in CMOS process, so this structure is suitable for CMOS technology. 3. Design of the Operational Amplifier in Instrumentation Amplifier The operational amplifier plays an important role in performance of system. Because the amplification magnitude of the sensor with the electric bridge structure is quite big, good noise restriction and low offset voltage are desirable for an amplifier. In order to guarantee the linearity of system, the operational amplifier must have a gain high enough. Besides, the total power consumption of the integrated system is also needed to be considered. Three-stage operational amplifier with capacitor-multiplier frequency compensation meets all these requirements. It could effectively avoid the low DC gain and high power consumption, which are draw-backs of typical two-stage operational amplifier. The diagram of the threestage operational amplifier is shown in figure 2. Fig.2 Three-stage operational amplifier with capacitor-multiplier frequency compensation

4 4038 M.Y. Ren et al. / Procedia Engineering 29 (2012) Fig.3 Frequency responses of the CMFC amplifier As shown in Fig.3, the frequency responses of the CMFC amplifier have been simulated with an input common-mode voltage of 1.65V. The dc gain, GBW, and phase margin are equal to120db, 1.699MHz, and 64, respectively. 4. Simulation of Instrumentation Amplifier Simulation results show that instrumentation amplifier with CMFC op-amp, operating voltage is 3.3V, supply current is 0.37mA, Bandwidth is 65kHz, differential-mode gain is 2, common-mode rejection ratio is 62dB, power supply rejection ratio is 73dB. The detailed performance of the instrumentation amplifier is summarized in Table 1. All these data suggest that CMFC structure can be used in low power instrumentation amplifier. Table 1 the performances of instrumentation amplifier Performance name Bandwidth Common scope Output swing Input offset voltage CMRR PSRR value 65kHz 0.7V~3.03V 0.02V~3.24V 0.27mV 62dB 73dB

5 M.Y. Ren et al. / Procedia Engineering 29 (2012) Conclusion A low-voltage instrumentation amplifier with CMFC topology has been described. Simulation results shows that the circuit can achieve a 62 db CMRR, while operating with a single 3.3 V power supply. The proposed circuit is suitable for a single-chip CMOS smart sensor. Acknowledgments This work is supported by National Natural Science Foundation of China under Grant Nos , Chun-Hui Cooperated Project of the Ministry of Education of China under Grant Nos. S , Young Science Foundation of Harbin University of Science and Technology under Grant Nos , Science and Technology Research Funds of Education Department in Heilongjiang Province under Grant Nos References [1] B. D.Miller and R. L. Sample, Instrumentation amplifier IC designed for oxygen sensor interface requirements, IEEE J. Solid-State Circuits, vol. 16, no. 6, pp , Dec [2] V. Schaffer, M. F. Snoeij, M. V. Ivanov, and D. T. Trifonov, A 36 V programmable instrumentation amplifier with sub-20 V offset and a CMRR in excess of 120 db at all gain settings, IEEE J. Solid-State Circuits, vol. 44, no. 7, pp , Jul [3] J.-M. Redouté and M. Steyaert, An instrumentation amplifier input circuit with a high immunity to EMI, in Proc Int. Symp. Electromagn. Compatibility EMC Eur., Hamburg, Germany, Sep. 2008, pp [4] J. F. Witte, J. H. Huijsing, and K. A. A. Makinwa, A current-feedback instrumentation amplifier with 5 V offset for bidirectional highside current-sensing, IEEE J. Solid-State Circuits, vol. 43, no. 12, pp , Dec [5] M. Rahal and A. Demosthenous, A synchronous chopping demodulator and implementation for high-frequency inductive position sensors, IEEE Trans. Instrum.Meas., vol. 58, no. 10, pp ,Oct [6] M. S. J. Steyaert, W. M. C. Sansen, and C. Zhongyuan, A micropower low-noise monolithic instrumentation amplifier for medical purposes, IEEE J. Solid-State Circuits, vol. SC-22, no. 6, pp , Dec [7] R. Martins, S. Selberherr, and F. A. Vaz, A CMOS IC for portable EEG acquisition systems, IEEE Trans. Instrum. Meas., vol. 47, no. 5, pp , Oct [8] C.-J. Yen, W.-Y. Chung, and M. C. Chi, Micro-power low-offset instrumentation amplifier IC design for biomedical system applications, IEEE Trans. Circuits Syst. I, Reg. Papers, vol. 51, no. 4, pp , Apr [9] K. A. Ng and P. K. Chan, A CMOS analog front-end IC for portable EEG/ECG monitoring applications, IEEE Trans. Circuits Syst. I, Reg. Papers, vol. 52, no. 11, pp , Nov [10] R. F. Yazicioglu, P. Merken, R. Puers, and C. V. Hoof, A 60 W 60 nv Hz readout front-end for portable biopotential acquisition systems, IEEE J. Solid-State Circuits, vol. 42, no. 5, pp , May [11] C.-C. Wang, C.-C. Huang, J.-S. Liou, Y.-J. Ciou, I-Y. Huang, C.-P. Li, Y.-C. Lee, andw.-j.wu, A mini-invasive longterm bladder urine pressure measurement ASIC and system, IEEE Trans. Biomed. Circuits Syst., vol. 2, no. 1, pp , Mar

Nizamuddin M., International Journal of Advance Research, Ideas and Innovations in Technology.

Nizamuddin M., International Journal of Advance Research, Ideas and Innovations in Technology. ISSN: 2454-132X Impact factor: 4.295 (Volume3, Issue1) Available online at: www.ijariit.com Design & Performance Analysis of Instrumentation Amplifier at Nanoscale Dr. M. Nizamuddin Assistant professor,

More information

ANALYSIS AND DESIGN OF HIGH CMRR INSTRUMENTATION AMPLIFIER FOR ECG SIGNAL ACQUISITION SYSTEM USING 180nm CMOS TECHNOLOGY

ANALYSIS AND DESIGN OF HIGH CMRR INSTRUMENTATION AMPLIFIER FOR ECG SIGNAL ACQUISITION SYSTEM USING 180nm CMOS TECHNOLOGY International Journal of Electronics and Communication Engineering (IJECE) ISSN 2278-9901 Vol. 2, Issue 4, Sep 2013, 67-74 IASET ANALYSIS AND DESIGN OF HIGH CMRR INSTRUMENTATION AMPLIFIER FOR ECG SIGNAL

More information

Noise George Yuan Hong Kong University of Science and Technology Fall 2010

Noise George Yuan Hong Kong University of Science and Technology Fall 2010 Lecture 3 Noise George Yuan Hong Kong University of Science and Technology Fall 2010 1 Outline Introduction Device noise models Circuit noise analysis Other noise sources Power noise Substrate noise Noise

More information

A 24 V Chopper Offset-Stabilized Operational Amplifier with Symmetrical RC Notch Filters having sub-10 µv offset and over-120db CMRR

A 24 V Chopper Offset-Stabilized Operational Amplifier with Symmetrical RC Notch Filters having sub-10 µv offset and over-120db CMRR ROMANIAN JOURNAL OF INFORMATION SCIENCE AND TECHNOLOGY Volume 20, Number 4, 2017, 301 312 A 24 V Chopper Offset-Stabilized Operational Amplifier with Symmetrical RC Notch Filters having sub-10 µv offset

More information

LP2902/LP324 Micropower Quad Operational Amplifier

LP2902/LP324 Micropower Quad Operational Amplifier LP2902/LP324 Micropower Quad Operational Amplifier General Description The LP324 series consists of four independent, high gain internally compensated micropower operational amplifiers. These amplifiers

More information

CHAPTER 3. Instrumentation Amplifier (IA) Background. 3.1 Introduction. 3.2 Instrumentation Amplifier Architecture and Configurations

CHAPTER 3. Instrumentation Amplifier (IA) Background. 3.1 Introduction. 3.2 Instrumentation Amplifier Architecture and Configurations CHAPTER 3 Instrumentation Amplifier (IA) Background 3.1 Introduction The IAs are key circuits in many sensor readout systems where, there is a need to amplify small differential signals in the presence

More information

MIC7300 A17. General Description. Features. Applications. Ordering Information. Pin Configurations. Functional Configuration.

MIC7300 A17. General Description. Features. Applications. Ordering Information. Pin Configurations. Functional Configuration. MIC7300 High-Output Drive Rail-to-Rail Op Amp General Description The MIC7300 is a high-performance CMOS operational amplifier featuring rail-to-rail input and output with strong output drive capability.

More information

Second-Order Sigma-Delta Modulator in Standard CMOS Technology

Second-Order Sigma-Delta Modulator in Standard CMOS Technology SERBIAN JOURNAL OF ELECTRICAL ENGINEERING Vol. 1, No. 3, November 2004, 37-44 Second-Order Sigma-Delta Modulator in Standard CMOS Technology Dragiša Milovanović 1, Milan Savić 1, Miljan Nikolić 1 Abstract:

More information

A CMOS Instrumentation Amplifier With 90-dB CMRR at 2-MHz Using Capacitive Neutralization: Analysis, Design Considerations, and Implementation

A CMOS Instrumentation Amplifier With 90-dB CMRR at 2-MHz Using Capacitive Neutralization: Analysis, Design Considerations, and Implementation IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 58, NO. 4, APRIL 2011 699 A CMOS Instrumentation Amplifier With 90-dB CMRR at 2-MHz Using Capacitive Neutralization: Analysis, Design Considerations,

More information

LF442 Dual Low Power JFET Input Operational Amplifier

LF442 Dual Low Power JFET Input Operational Amplifier LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while

More information

MIC7122. General Description. Features. Applications. Ordering Information. Pin Configuration. Pin Description. Rail-to-Rail Dual Op Amp

MIC7122. General Description. Features. Applications. Ordering Information. Pin Configuration. Pin Description. Rail-to-Rail Dual Op Amp MIC722 Rail-to-Rail Dual Op Amp General Description The MIC722 is a dual high-performance CMOS operational amplifier featuring rail-to-rail inputs and outputs. The input common-mode range extends beyond

More information

Low-Power, Precision, 4-Bump WLP, Current-Sense Amplifier

Low-Power, Precision, 4-Bump WLP, Current-Sense Amplifier EVALUATION KIT AVAILABLE General Description The is a zero-drift, high-side current-sense amplifier family that offers precision, low supply current and is available in a tiny 4-bump ultra-thin WLP of

More information

LM837 Low Noise Quad Operational Amplifier

LM837 Low Noise Quad Operational Amplifier LM837 Low Noise Quad Operational Amplifier General Description The LM837 is a quad operational amplifier designed for low noise, high speed and wide bandwidth performance. It has a new type of output stage

More information

A Novel Low Noise High Gain CMOS Instrumentation Amplifier for Biomedical Applications

A Novel Low Noise High Gain CMOS Instrumentation Amplifier for Biomedical Applications International Journal of Electrical and Computer Engineering (IJECE) Vol. 3, No. 4, August 2013, pp. 516~523 ISSN: 2088-8708 516 A Novel Low Noise High Gain CMOS Instrumentation Amplifier for Biomedical

More information

CMOS Instrumentation Amplifier with Offset Cancellation Circuitry for Biomedical Application

CMOS Instrumentation Amplifier with Offset Cancellation Circuitry for Biomedical Application CMOS Instrumentation Amplifier with Offset Cancellation Circuitry for Biomedical Application Author Mohd-Yasin, Faisal, Yap, M., I Reaz, M. Published 2006 Conference Title 5th WSEAS Int. Conference on

More information

Design and Performance Analysis of Low Power RF Operational Amplifier using CMOS and BiCMOS Technology

Design and Performance Analysis of Low Power RF Operational Amplifier using CMOS and BiCMOS Technology Proc. of Int. Conf. on Recent Trends in Information, Telecommunication and Computing, ITC Design and Performance Analysis of Low Power RF Operational Amplifier using CMOS and BiCMOS Technology A. Baishya

More information

A Complete Analog Front-End IC Design for ECG Signal Acquisition

A Complete Analog Front-End IC Design for ECG Signal Acquisition A Complete Analog Front-End IC Design for ECG Signal Acquisition Yang Xu, Yanling Wu, Xiaotong Jia School of Electrical and Computer Engineering Georgia Institute of Technology yxu327@gatech.edu, yanlingwu@gatech.edu,

More information

Comparison between Analog and Digital Current To PWM Converter for Optical Readout Systems

Comparison between Analog and Digital Current To PWM Converter for Optical Readout Systems Comparison between Analog and Digital Current To PWM Converter for Optical Readout Systems 1 Eun-Jung Yoon, 2 Kangyeob Park, 3* Won-Seok Oh 1, 2, 3 SoC Platform Research Center, Korea Electronics Technology

More information

IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 43, NO. 12, DECEMBER

IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 43, NO. 12, DECEMBER IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 43, NO. 12, DECEMBER 2008 2769 A Current-Feedback Instrumentation Amplifier With 5 V Offset for Bidirectional High-Side Current-Sensing Johan F. Witte, Member,

More information

Design of High gain and Low Offset CMOS Current Mode Front End Operational Amplifier

Design of High gain and Low Offset CMOS Current Mode Front End Operational Amplifier Design of High gain and Low Offset CMOS Current Mode Front End Operational Amplifier R.SHANTHA SELVA KUMARI 1, M.VIJAYALAKSHMI 2 1 Professor and Head, 2 Student, Department of Electronics and Communication

More information

Low Power and Fast Transient High Swing CMOS Telescopic Operational Amplifier

Low Power and Fast Transient High Swing CMOS Telescopic Operational Amplifier RESEARCH ARTICLE OPEN ACCESS Low Power and Fast Transient High Swing CMOS Telescopic Operational Amplifier Akshay Kumar Kansal 1, Asst Prof. Gayatri Sakya 2 Electronics and Communication Department, 1,2

More information

1100 IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 42, NO. 5, MAY 2007

1100 IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 42, NO. 5, MAY 2007 1100 IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 42, NO. 5, MAY 2007 A60W 60 nv/ Hz Readout Front-End for Portable Biopotential Acquisition Systems Refet Firat Yazicioglu, Patrick Merken, Robert Puers,

More information

1.0V Micropower, SOT23, Operational Amplifier

1.0V Micropower, SOT23, Operational Amplifier 19-3; Rev ; 1/ 1.V Micropower, SOT3, Operational Amplifier General Description The micropower, operational amplifier is optimized for ultra-low supply voltage operation. The amplifier consumes only 9µA

More information

Features. Applications SOT-23-5 (M5)

Features. Applications SOT-23-5 (M5) 1.8V to 11V, 15µA, 25kHz GBW, Rail-to-Rail Input and Output Operational Amplifier General Description The is a low-power operational amplifier with railto-rail inputs and outputs. The device operates from

More information

Differential Amplifier : input. resistance. Differential amplifiers are widely used in engineering instrumentation

Differential Amplifier : input. resistance. Differential amplifiers are widely used in engineering instrumentation Differential Amplifier : input resistance Differential amplifiers are widely used in engineering instrumentation Differential Amplifier : input resistance v 2 v 1 ir 1 ir 1 2iR 1 R in v 2 i v 1 2R 1 Differential

More information

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp MIC915 Dual 135MHz Low-Power Op Amp General Description The MIC915 is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply

More information

LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator

LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated

More information

LM833 Dual Audio Operational Amplifier

LM833 Dual Audio Operational Amplifier LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier

More information

UNISONIC TECHNOLOGIES CO., LTD LM321

UNISONIC TECHNOLOGIES CO., LTD LM321 UNISONIC TECHNOLOGIES CO., LTD LM321 LOW POWER SINGLE OP AMP DESCRIPTION The UTC LM321 s quiescent current is only 430µA (5V). The UTC LM321 brings performance and economy to low power systems, With a

More information

ISSN:

ISSN: 468 Modeling and Design of a CMOS Low Drop-out (LDO) Voltage Regulator PRIYADARSHINI JAINAPUR 1, CHIRAG SHARMA 2 1 Department of E&CE, Nitte Meenakshi Institute of Technology, Yelahanka, Bangalore-560064,

More information

High Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection

High Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements

More information

Dual operational amplifier

Dual operational amplifier DESCRIPTION The 77 is a pair of high-performance monolithic operational amplifiers constructed on a single silicon chip. High common-mode voltage range and absence of latch-up make the 77 ideal for use

More information

Design of Low Voltage High Speed Operational Amplifier for Pipelined ADC in 90 nm Standard CMOS Process

Design of Low Voltage High Speed Operational Amplifier for Pipelined ADC in 90 nm Standard CMOS Process Design of Low Voltage High Speed Operational Amplifier for Pipelined ADC in 90 nm Standard CMOS Process Shri Kant M.Tech. (VLSI student), Department of electronics and communication engineering NIT Kurukshetra,

More information

Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM392 Low Power Operational Amplifier/Voltage Comparator General Description

More information

CMOS Quad Rail-to-Rail I/O Op Amp DESCRIPTION: FEATURES: Logic Diagram

CMOS Quad Rail-to-Rail I/O Op Amp DESCRIPTION: FEATURES: Logic Diagram 6484 CMOS Quad Rail-to-Rail I/O Op Amp V+ IN+A IN+D IN-A OUT A OUT D IN-D V- IN+B OUT B OUT C IN+C IN-B Logic Diagram IN-C FEATURES: Rad-Pak technology-hardened against natural space radiation Total dose

More information

LOW POWER QUAD OPERATIONAL AMPLIFIERS General Description. Features. Applications

LOW POWER QUAD OPERATIONAL AMPLIFIERS General Description. Features. Applications General Description Features The consists of four independent, high gain and internally frequency compensated operational amplifiers. It is specifically designed to operate from a single power supply.

More information

Design of an Amplifier for Sensor Interfaces

Design of an Amplifier for Sensor Interfaces Design of an Amplifier for Sensor Interfaces Anurag Mangla Electrical and Electronics Engineering anurag.mangla@epfl.ch Supervised by Dr. Marc Pastre Prof. Maher Kayal Outline Introduction Need for high

More information

LM833 Dual Audio Operational Amplifier

LM833 Dual Audio Operational Amplifier LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier

More information

Pankaj Naik Electronic and Instrumentation Deptt. SGSITS, Indore, India. Priyanka Sharma Electronic and. SGSITS, Indore, India

Pankaj Naik Electronic and Instrumentation Deptt. SGSITS, Indore, India. Priyanka Sharma Electronic and. SGSITS, Indore, India Designing Of Current Mode Instrumentation Amplifier For Bio-Signal Using 180nm CMOS Technology Sonu Mourya Electronic and Instrumentation Deptt. SGSITS, Indore, India Pankaj Naik Electronic and Instrumentation

More information

Micropower, Single-Supply, Rail-to-Rail, Precision Instrumentation Amplifiers MAX4194 MAX4197

Micropower, Single-Supply, Rail-to-Rail, Precision Instrumentation Amplifiers MAX4194 MAX4197 General Description The is a variable-gain precision instrumentation amplifier that combines Rail-to-Rail single-supply operation, outstanding precision specifications, and a high gain bandwidth. This

More information

DUAL ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER

DUAL ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER ADVANCED LINEAR DEVICES, INC. ALD276A/ALD276B ALD276 DUAL ULTRA MICROPOWER RAILTORAIL CMOS OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The ALD276 is a dual monolithic CMOS micropower high slewrate operational

More information

Design and Simulation of Low Dropout Regulator

Design and Simulation of Low Dropout Regulator Design and Simulation of Low Dropout Regulator Chaitra S Kumar 1, K Sujatha 2 1 MTech Student, Department of Electronics, BMSCE, Bangalore, India 2 Assistant Professor, Department of Electronics, BMSCE,

More information

PIN CONFIGURATIONS FEATURES APPLICATION ORDERING INFORMATION. FE, N Packages

PIN CONFIGURATIONS FEATURES APPLICATION ORDERING INFORMATION. FE, N Packages DESCRIPTION The are monolithic sample-and-hold circuits which utilize high-voltage ion-implant JFET technology to obtain ultra-high DC accuracy with fast acquisition of signal and low droop rate. Operating

More information

NE/SA5234 Matched quad high-performance low-voltage operational amplifier

NE/SA5234 Matched quad high-performance low-voltage operational amplifier INTEGRATED CIRCUITS Supersedes data of 2001 Aug 03 File under Integrated Circuits, IC11 Handbook 2002 Feb 22 DESCRIPTION The is a matched, low voltage, high performance quad operational amplifier. Among

More information

A CMOS Low-Voltage, High-Gain Op-Amp

A CMOS Low-Voltage, High-Gain Op-Amp A CMOS Low-Voltage, High-Gain Op-Amp G N Lu and G Sou LEAM, Université Pierre et Marie Curie Case 203, 4 place Jussieu, 75252 Paris Cedex 05, France Telephone: (33 1) 44 27 75 11 Fax: (33 1) 44 27 48 37

More information

Design of a low voltage,low drop-out (LDO) voltage cmos regulator

Design of a low voltage,low drop-out (LDO) voltage cmos regulator Design of a low,low drop-out (LDO) cmos regulator Chaithra T S Ashwini Abstract- In this paper a low, low drop-out (LDO) regulator design procedure is proposed and implemented using 0.25 micron CMOS process.

More information

A Multichannel Pipeline Analog-to-Digital Converter for an Integrated 3-D Ultrasound Imaging System

A Multichannel Pipeline Analog-to-Digital Converter for an Integrated 3-D Ultrasound Imaging System 1266 IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 38, NO. 7, JULY 2003 A Multichannel Pipeline Analog-to-Digital Converter for an Integrated 3-D Ultrasound Imaging System Kambiz Kaviani, Student Member,

More information

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage

More information

ROHM Op Amps: Pursuing a Completely Noiseless Design

ROHM Op Amps: Pursuing a Completely Noiseless Design ROHM Op Amps: Pursuing a Completely less Design Revolutionary noise design achieves refined operation featuring greater accuracy 2 Op Amps that pave the way to the sensing technology of tomorrow The importance

More information

LMC7101 A12A. Features. General Description. Applications. Ordering Information. Pin Configuration. Functional Configuration.

LMC7101 A12A. Features. General Description. Applications. Ordering Information. Pin Configuration. Functional Configuration. LMC7 LMC7 Low-Power Operational Amplifier Final Information General Description The LMC7 is a high-performance, low-power, operational amplifier which is pin-for-pin compatible with the National Semiconductor

More information

Dual Low Power Operational Amplifier, Single or Dual Supply OP221

Dual Low Power Operational Amplifier, Single or Dual Supply OP221 a FEATURES Excellent TCV OS Match, 2 V/ C Max Low Input Offset Voltage, 15 V Max Low Supply Current, 55 A Max Single Supply Operation, 5 V to 3 V Low Input Offset Voltage Drift,.75 V/ C High Open-Loop

More information

LMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output

LMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output General Description The LMV301 CMOS operational amplifier is ideal for single supply, low voltage operation with a guaranteed operating voltage

More information

EC kHz, 7μA, CMOS, Rail-to-Rail Operational Amplifier. General Description. Features. Applications. Pin Assignments

EC kHz, 7μA, CMOS, Rail-to-Rail Operational Amplifier. General Description. Features. Applications. Pin Assignments General Description Features The is a single supply, low power CMOS operational amplifier; these amplifiers offer bandwidth of 250kHz, rail-to-rail inputs and outputs, and single-supply operation from

More information

Features. Ordering Information. Part Identification

Features. Ordering Information. Part Identification MIC9 MHz Low-Power SC-7 Op Amp General Description The MIC9 is a high-speed operational amplifier with a gain-bandwidth product of MHz. The part is unity gain stable. It has a very low.ma supply current,

More information

LF353 Wide Bandwidth Dual JFET Input Operational Amplifier

LF353 Wide Bandwidth Dual JFET Input Operational Amplifier LF353 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage

More information

LM833 Dual Audio Operational Amplifier

LM833 Dual Audio Operational Amplifier LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier

More information

Advances In Natural And Applied Sciences Homepage: October; 12(10): pages 1-7 DOI: /anas

Advances In Natural And Applied Sciences Homepage: October; 12(10): pages 1-7 DOI: /anas Advances In Natural And Applied Sciences Homepage: http://www.aensiweb.com/anas/ 2018 October; 12(10): pages 1-7 DOI: 10.22587/anas.2018.12.10.1 Research Article AENSI Publications Design of CMOS Architecture

More information

Single-Supply, 150MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps

Single-Supply, 150MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps 9-; Rev ; /8 Single-Supply, 5MHz, 6-Bit Accurate, General Description The MAX4434/MAX4435 single and MAX4436/MAX4437 dual operational amplifiers feature wide bandwidth, 6- bit settling time in 3ns, and

More information

A Chopper Modulated Instrumentation Amplifier Using Spike Shaping and Delayed Modulation Techniques for MEMS Pressure Sensor

A Chopper Modulated Instrumentation Amplifier Using Spike Shaping and Delayed Modulation Techniques for MEMS Pressure Sensor N. P. Futane, C. Roychaudhuri and H. Saha Vol. 2, 155 A Chopper Modulated Instrumentation Amplifier Using Spike Shaping and Delayed Modulation Techniques for MEMS Pressure Sensor Abstract A low-noise chopper

More information

ELM824xA 3.0μA Very low power CMOS dual operational amplifier

ELM824xA 3.0μA Very low power CMOS dual operational amplifier ELM824xA 3.μA Very low power CMOS dual operational amplifier General description ELM824xA is a very low current consumption-typ.3.μa CMOS dual OP-AMP provided with a wide common mode input voltage range.

More information

Four-Channel Sample-and-Hold Amplifier AD684

Four-Channel Sample-and-Hold Amplifier AD684 a FEATURES Four Matched Sample-and-Hold Amplifiers Independent Inputs, Outputs and Control Pins 500 ns Hold Mode Settling 1 s Maximum Acquisition Time to 0.01% Low Droop Rate: 0.01 V/ s Internal Hold Capacitors

More information

LM675 Power Operational Amplifier

LM675 Power Operational Amplifier LM675 Power Operational Amplifier General Description The LM675 is a monolithic power operational amplifier featuring wide bandwidth and low input offset voltage, making it equally suitable for AC and

More information

Design and Analysis of High Gain Differential Amplifier Using Various Topologies

Design and Analysis of High Gain Differential Amplifier Using Various Topologies Design and Analysis of High Gain Amplifier Using Various Topologies SAMARLA.SHILPA 1, J SRILATHA 2 1Assistant Professor, Dept of Electronics and Communication Engineering, NNRG, Ghatkesar, Hyderabad, India.

More information

A PSEUDO-CLASS-AB TELESCOPIC-CASCODE OPERATIONAL AMPLIFIER

A PSEUDO-CLASS-AB TELESCOPIC-CASCODE OPERATIONAL AMPLIFIER A PSEUDO-CLASS-AB TELESCOPIC-CASCODE OPERATIONAL AMPLIFIER M. Taherzadeh-Sani, R. Lotfi, and O. Shoaei ABSTRACT A novel class-ab architecture for single-stage operational amplifiers is presented. The structure

More information

Summary 185. Chapter 4

Summary 185. Chapter 4 Summary This thesis describes the theory, design and realization of precision interface electronics for bridge transducers and thermocouples that require high accuracy, low noise, low drift and simultaneously,

More information

A DRY ELECTRODE LOW POWER CMOS EEG ACQUISITION SOC FOR SEIZURE DETECTION

A DRY ELECTRODE LOW POWER CMOS EEG ACQUISITION SOC FOR SEIZURE DETECTION A DRY ELECTRODE LOW POWER CMOS EEG ACQUISITION SOC FOR SEIZURE DETECTION TEAM 6: MATTHIEU DURBEC, VALENTIN BERANGER, KARIM ELOUELDRHIRI ECE 6414 SPRING 2017 OUTLINE Project motivation Design overview Body-Electrode

More information

An Ultralow-Power Low-Voltage Fully Differential Opamp for Long-Life Autonomous Portable Equipment

An Ultralow-Power Low-Voltage Fully Differential Opamp for Long-Life Autonomous Portable Equipment International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 7, Issue 1 (May 2013), PP. 81-85 An Ultralow-Power Low-Voltage Fully Differential

More information

OBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units

OBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units a FEATURES MHz Small Signal Bandwidth MHz Large Signal BW ( V p-p) High Slew Rate: V/ s Low Distortion: db @ MHz Fast Settling: ns to.%. nv/ Hz Spectral Noise Density V Supply Operation Wideband Voltage

More information

A Switched-Capacitor Band-Pass Biquad Filter Using a Simple Quasi-unity Gain Amplifier

A Switched-Capacitor Band-Pass Biquad Filter Using a Simple Quasi-unity Gain Amplifier A Switched-Capacitor Band-Pass Biquad Filter Using a Simple Quasi-unity Gain Amplifier Hugo Serra, Nuno Paulino, and João Goes Centre for Technologies and Systems (CTS) UNINOVA Dept. of Electrical Engineering

More information

Simran Singh Student, School Of ICT Gautam Buddha University Greater Noida

Simran Singh Student, School Of ICT Gautam Buddha University Greater Noida An Ultra Low-Voltage CMOS Self-Biased OTA Simran Singh Student, School Of ICT Gautam Buddha University Greater Noida simransinghh386@gmail.com Priyanka Goyal Faculty Associate, School Of ICT Gautam Buddha

More information

A low-if 2.4 GHz Integrated RF Receiver for Bluetooth Applications Lai Jiang a, Shaohua Liu b, Hang Yu c and Yan Li d

A low-if 2.4 GHz Integrated RF Receiver for Bluetooth Applications Lai Jiang a, Shaohua Liu b, Hang Yu c and Yan Li d Applied Mechanics and Materials Online: 2013-06-27 ISSN: 1662-7482, Vol. 329, pp 416-420 doi:10.4028/www.scientific.net/amm.329.416 2013 Trans Tech Publications, Switzerland A low-if 2.4 GHz Integrated

More information

High Voltage and Temperature Auto Zero Op-Amp Cell Features Applications Process Technology Introduction Parameter Unit Rating

High Voltage and Temperature Auto Zero Op-Amp Cell Features Applications Process Technology Introduction Parameter Unit Rating Analogue Integration AISC11 High Voltage and Temperature Auto Zero Op-Amp Cell Rev.1 12-1-5 Features High Voltage Operation: 4.5-3 V Precision, Auto-Zeroed Input Vos High Temperature Operation Low Quiescent

More information

ANALYSIS AND DESIGN OF CMOS SMART TEMPERATURE SENSOR (SMT)

ANALYSIS AND DESIGN OF CMOS SMART TEMPERATURE SENSOR (SMT) ANALYSIS AND DESIGN OF CMOS SMART TEMPERATURE SENSOR (SMT) WITH DUTY-CYCLE MODULATED OUTPUT Kataneh Kohbod, Gerard C.M. Meijer Electronic Instrumentation Laboratory, Delft University of Technology Mekelweg

More information

A 12-bit 100kS/s SAR ADC for Biomedical Applications. Sung-Chan Rho 1 and Shin-Il Lim 2. Seoul, Korea. Abstract

A 12-bit 100kS/s SAR ADC for Biomedical Applications. Sung-Chan Rho 1 and Shin-Il Lim 2. Seoul, Korea. Abstract , pp.17-22 http://dx.doi.org/10.14257/ijunesst.2016.9.8.02 A 12-bit 100kS/s SAR ADC for Biomedical Applications Sung-Chan Rho 1 and Shin-Il Lim 2 1 Department of Electronics and Computer Engineering, Seokyeong

More information

6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable

6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable 99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using

More information

CONDUCTIVITY sensors are required in many application

CONDUCTIVITY sensors are required in many application IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT, VOL. 54, NO. 6, DECEMBER 2005 2433 A Low-Cost and Accurate Interface for Four-Electrode Conductivity Sensors Xiujun Li, Senior Member, IEEE, and Gerard

More information

James Lunsford HW2 2/7/2017 ECEN 607

James Lunsford HW2 2/7/2017 ECEN 607 James Lunsford HW2 2/7/2017 ECEN 607 Problem 1 Part A Figure 1: Negative Impedance Converter To find the input impedance of the above NIC, we use the following equations: V + Z N V O Z N = I in, V O kr

More information

ALow Voltage Wide-Input-Range Bulk-Input CMOS OTA

ALow Voltage Wide-Input-Range Bulk-Input CMOS OTA Analog Integrated Circuits and Signal Processing, 43, 127 136, 2005 c 2005 Springer Science + Business Media, Inc. Manufactured in The Netherlands. ALow Voltage Wide-Input-Range Bulk-Input CMOS OTA IVAN

More information

LF444 Quad Low Power JFET Input Operational Amplifier

LF444 Quad Low Power JFET Input Operational Amplifier LF444 Quad Low Power JFET Input Operational Amplifier General Description The LF444 quad low power operational amplifier provides many of the same AC characteristics as the industry standard LM148 while

More information

DESIGN OF A NOVEL CURRENT MIRROR BASED DIFFERENTIAL AMPLIFIER DESIGN WITH LATCH NETWORK. Thota Keerthi* 1, Ch. Anil Kumar 2

DESIGN OF A NOVEL CURRENT MIRROR BASED DIFFERENTIAL AMPLIFIER DESIGN WITH LATCH NETWORK. Thota Keerthi* 1, Ch. Anil Kumar 2 ISSN 2277-2685 IJESR/October 2014/ Vol-4/Issue-10/682-687 Thota Keerthi et al./ International Journal of Engineering & Science Research DESIGN OF A NOVEL CURRENT MIRROR BASED DIFFERENTIAL AMPLIFIER DESIGN

More information

LF442 Dual Low Power JFET Input Operational Amplifier

LF442 Dual Low Power JFET Input Operational Amplifier LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while

More information

Rail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP

Rail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP 19-579; Rev ; 12/1 EVALUATION KIT AVAILABLE Rail-to-Rail, 2kHz Op Amp General Description The op amp features a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for battery-powered

More information

LF444 Quad Low Power JFET Input Operational Amplifier

LF444 Quad Low Power JFET Input Operational Amplifier LF444 Quad Low Power JFET Input Operational Amplifier General Description The LF444 quad low power operational amplifier provides many of the same AC characteristics as the industry standard LM148 while

More information

CLC440 High Speed, Low Power, Voltage Feedback Op Amp

CLC440 High Speed, Low Power, Voltage Feedback Op Amp CLC440 High Speed, Low Power, Voltage Feedback Op Amp General Description The CLC440 is a wideband, low power, voltage feedback op amp that offers 750MHz unity-gain bandwidth, 1500V/µs slew rate, and 90mA

More information

Design and Analysis of Low Power Two Stage CMOS Op- Amp with 50nm Technology

Design and Analysis of Low Power Two Stage CMOS Op- Amp with 50nm Technology Design and Analysis of Low Power Two Stage CMOS Op- Amp with 50nm Technology Swetha Velicheti, Y. Sandhyarani, P.Praveen kumar, B.Umamaheshrao Assistant Professor, Dept. of ECE, SSCE, Srikakulam, A.P.,

More information

Precision, 16 MHz CBFET Op Amp AD845

Precision, 16 MHz CBFET Op Amp AD845 a FEATURES Replaces Hybrid Amplifiers in Many Applications AC PERFORMANCE: Settles to 0.01% in 350 ns 100 V/ s Slew Rate 12.8 MHz Min Unity Gain Bandwidth 1.75 MHz Full Power Bandwidth at 20 V p-p DC PERFORMANCE:

More information

LM6142 and LM MHz Rail-to-Rail Input-Output Operational Amplifiers

LM6142 and LM MHz Rail-to-Rail Input-Output Operational Amplifiers LM6142 and LM6144 17 MHz Rail-to-Rail Input-Output Operational Amplifiers General Description Using patent pending new circuit topologies, the LM6142/44 provides new levels of performance in applications

More information

LMC6492 Dual/LMC6494 Quad CMOS Rail-to-Rail Input and Output Operational Amplifier

LMC6492 Dual/LMC6494 Quad CMOS Rail-to-Rail Input and Output Operational Amplifier CMOS Rail-to-Rail Input and Output Operational Amplifier General Description The LMC6492/LMC6494 amplifiers were specifically developed for single supply applications that operate from 40 C to +125 C.

More information

Low Noise, CMOS Rail-to-Rail Output Operational Amplifiers. 1.8 V to 5 V Auto-Zero Instrumentation Amplifier with Shutdown

Low Noise, CMOS Rail-to-Rail Output Operational Amplifiers. 1.8 V to 5 V Auto-Zero Instrumentation Amplifier with Shutdown Low Noise, CMOS Rail-to-Rail Output Operational Amplifiers The AD8691 family combines a number of high performance parameters including low 8 nv/ Hz voltage noise density, rail-to-rail output, extended

More information

Design Analysis and Performance Comparison of Low Power High Gain 2nd Stage Differential Amplifier Along with 1st Stage

Design Analysis and Performance Comparison of Low Power High Gain 2nd Stage Differential Amplifier Along with 1st Stage Design Analysis and Performance Comparison of Low Power High Gain 2nd Stage Differential Amplifier Along with 1st Stage Sadeque Reza Khan Department of Electronic and Communication Engineering, National

More information

QUAD 5V RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER

QUAD 5V RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER ADVANCED LINEAR DEVICES, INC. ALD472A/ALD472B ALD472 QUAD 5V RAILTORAIL PRECISION OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The ALD472 is a quad monolithic precision CMOS railtorail operational amplifier

More information

High Voltage Operational Amplifiers in SOI Technology

High Voltage Operational Amplifiers in SOI Technology High Voltage Operational Amplifiers in SOI Technology Kishore Penmetsa, Kenneth V. Noren, Herbert L. Hess and Kevin M. Buck Department of Electrical Engineering, University of Idaho Abstract This paper

More information

DESIGNING OF CURRENT MODE INSTRUMENTATION AMPLIFIER FOR BIO-SIGNAL USING 180NM CMOS TECHNOLOGY

DESIGNING OF CURRENT MODE INSTRUMENTATION AMPLIFIER FOR BIO-SIGNAL USING 180NM CMOS TECHNOLOGY DESIGNING OF CURRENT MODE INSTRUMENTATION AMPLIFIER FOR BIO-SIGNAL USING 180NM CMOS TECHNOLOGY GAYTRI GUPTA AMITY University Email: Gaytri.er@gmail.com Abstract In this paper we have describes the design

More information

LMC7101 Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output

LMC7101 Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output General Description The LMC7101 is a high performance CMOS operational amplifier available in the space saving SOT 23-5 Tiny package.

More information

Designing CMOS folded-cascode operational amplifier with flicker noise minimisation

Designing CMOS folded-cascode operational amplifier with flicker noise minimisation Microelectronics Journal 32 (200) 69 73 Short Communication Designing CMOS folded-cascode operational amplifier with flicker noise minimisation P.K. Chan*, L.S. Ng, L. Siek, K.T. Lau Microelectronics Journal

More information

Features. Ordering Information. Part Number Standard Marking Pb-Free Marking

Features. Ordering Information. Part Number Standard Marking Pb-Free Marking MIC9 MIC9 8MHz Low-Power SC-7 Op Amp General Description The MIC9 is a high-speed operational amplifier with a gain-bandwidth product of 8MHz. The part is unity gain stable. It has a very low µa supply

More information

I/O Op Amps with Shutdown

I/O Op Amps with Shutdown MHz, μa, Rail-to-Rail General Description The single MAX994/MAX995 and dual MAX996/ MAX997 operational amplifiers feature maximized ratio of gain bandwidth to supply current and are ideal for battery-powered

More information

LM9044 Lambda Sensor Interface Amplifier

LM9044 Lambda Sensor Interface Amplifier LM9044 Lambda Sensor Interface Amplifier General Description The LM9044 is a precision differential amplifier specifically designed for operation in the automotive environment. Gain accuracy is guaranteed

More information

Features. Applications SOT-23-5

Features. Applications SOT-23-5 135MHz, Low-Power SOT-23-5 Op Amp General Description The is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply current,

More information

LF412 Low Offset, Low Drift Dual JFET Input Operational Amplifier

LF412 Low Offset, Low Drift Dual JFET Input Operational Amplifier LF412 Low Offset, Low Drift Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, JFET input operational amplifiers with very low input offset voltage and guaranteed

More information