ETSI EN V2.1.1 ( )

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "ETSI EN V2.1.1 ( )"

Transcription

1 EN V2.1.1 ( ) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 5: Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and non-speech) and Terrestrial Trunked Radio (TETRA); Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU

2 2 EN V2.1.1 ( ) Reference REN/ERM-EMC-345 Keywords EMC, harmonised standard, PMR, radio, regulation, TETRA 650 Route des Lucioles F Sophia Antipolis Cedex - FRANCE Tel.: Fax: Siret N NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of. The content of the PDF version shall not be modified without the written authorization of. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute All rights reserved. DECT TM, PLUGTESTS TM, UMTS TM and the logo are Trade Marks of registered for the benefit of its Members. 3GPP TM and LTE are Trade Marks of registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.

3 3 EN V2.1.1 ( ) Contents Intellectual Property Rights... 5 Foreword... 5 Modal verbs terminology Scope References Normative references Informative references Definitions and abbreviations Definitions Abbreviations Test conditions General Arrangements for test signals General Arrangements for test signals at the input of transmitters Arrangements for test signals at the output of transmitters Arrangements for test signals at the input of receivers Arrangements for test signals at the output of receivers Arrangements for testing transmitter and receiver together (as a system) Exclusion bands General Receiver and receivers of transceivers exclusion band Transmitter exclusion band Narrow band responses of receivers Normal test modulation General Analogue speech equipment Angle modulated equipment Non-angle modulated equipment Digital speech equipment Non-speech equipment (data, specific response, etc.) TETRA equipment Performance assessment General Equipment which can provide a continuous communications link Equipment which does not provide a continuous communications link Ancillary equipment Equipment classification Performance assessment of equipment providing an audio path Introduction Assessment of audio path using the audio breakthrough method Assessment of audio path using the audio distortion method Performance criteria General Performance criteria for Continuous phenomena applied to Transmitters (CT) Performance criteria for Transient phenomena applied to Transmitters (TT) Performance criteria for Continuous phenomena applied to Receivers (CR) Performance criteria for Transient phenomena applied to Receivers (TR) Performance criteria for ancillary equipment tested on a stand alone basis Applicability overview Emission General... 15

4 4 EN V2.1.1 ( ) Special conditions Immunity General Special conditions Annex A (normative): Annex B (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU Examples of PMR equipment in the scope of the present document B.1 Introduction B.2 Non-integral antenna PMR equipment B.3 Integral antenna PMR equipment B.4 Narrowband channel non-integral PMR equipment B.5 Mobile, base station, and portable equipment of TErrestrial Trunked Radio (TETRA) equipment Annex C (informative): Bibliography History... 21

5 5 EN V2.1.1 ( ) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to. The information pertaining to these essential IPRs, if any, is publicly available for members and non-members, and can be found in SR : "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to in respect of standards", which is available from the Secretariat. Latest updates are available on the Web server ( Pursuant to the IPR Policy, no investigation, including IPR searches, has been carried out by. No guarantee can be given as to the existence of other IPRs not referenced in SR (or the updates on the Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document is part 5 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1]. National transposition dates Date of adoption of this EN: 19 July 2016 Date of latest announcement of this EN (doa): 31 October 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 April 2017 Date of withdrawal of any conflicting National Standard (dow): 30 April 2018 Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in deliverables except when used in direct citation.

6 6 EN V2.1.1 ( ) 1 Scope The present document, together with, covers the assessment of Private land Mobile Radio (PMR) and associated ancillary equipment, in respect of ElectroMagnetic Compatibility (EMC). The present document covers both analogue and digital Private land Mobile Radio (PMR) equipment. Technical specifications related to the antenna port and emissions from the enclosure port of Private land Mobile Radio (PMR) equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment and performance criteria for Private land Mobile Radio (PMR) equipment and associated ancillary equipment. Examples of Private Mobile Radio equipment are given in annex B. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and, the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in, except for any special conditions included in the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at NOTE: While any hyperlinks included in this clause were valid at the time of publication, cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] EN (V2.1.1) ( ): "ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU". [2] EN (V3.3.1) ( ): "Terrestrial Trunked Radio (TETRA); Conformance testing specification; Part 1: Radio". [3] EN (V1.3.1) ( ): "Terrestrial Trunked Radio (TETRA); Speech codec for full-rate traffic channel; Part 2: TETRA codec". [4] EN (V3.4.1) ( ): "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air Interface (AI)". [5] EN (V1.4.1) ( ): "Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 2: Radio aspects".

7 7 EN V2.1.1 ( ) 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] [i.2] [i.3] [i.4] [i.5] [i.6] [i.7] [i.8] [i.9] [i.10] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. EN : "Land Mobile Service; Radio equipment using constant or non-constant envelope modulation operating in a channel bandwidth of 25 khz, 50 khz, 100 khz or 150 khz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". Commission Implementing Decision C(2015) 5376 final of on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. ETS : "Radio Equipment and Systems (RES); Land mobile group; Technical characteristics and test conditions for radio equipment with an internal or external RF connector intended primarily for analogue speech". I-ETS : "Radio Equipment and Systems (RES); Land mobile service; Technical characteristics and test conditions for radio equipment transmitting signals to initiate a specific response in the receiver". EN : "Land Mobile Service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". EN : "Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". EN : "Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". EN : "Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". EN : "Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU".

8 8 EN V2.1.1 ( ) 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in, clause 3, apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in, clause 3 and the following apply: BER CR CT EUT PMR TR TT Bit Error Ratio Continuous phenomena applied to Receivers Continuous phenomena applied to Transmitters Equipment Under Test Private land Mobile Radio Transient phenomena applied to Receivers Transient phenomena applied to Transmitters 4 Test conditions 4.1 General For the purposes of the present document, the test conditions of, clause 4 shall apply as appropriate. Further product related test conditions for PMR equipment are specified in the present document. For emission and immunity tests the test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply. 4.2 Arrangements for test signals General The provisions of, clause 4.2 shall apply Arrangements for test signals at the input of transmitters The provisions of, clause shall apply Arrangements for test signals at the output of transmitters The provisions of, clause shall apply with the following modification. The transmitter shall be operated at its maximum rated RF output power, modulated with normal test modulation (see clause 4.5) Arrangements for test signals at the input of receivers The provisions of, clause shall apply with the following modification. A communication link shall be established at the start of the test and maintained during the test.

9 9 EN V2.1.1 ( ) Arrangements for test signals at the output of receivers The provisions of, clause shall apply Arrangements for testing transmitter and receiver together (as a system) The provisions of, clause shall apply with the following modification. For the immunity tests of duplex transceivers, the EUT may be configured in the repeater mode, consistent with the conditions given above. 4.3 Exclusion bands General The provisions of, clause 4.3 shall apply Receiver and receivers of transceivers exclusion band The exclusion band for receivers and receivers of transceivers is the frequency range determined by the switching range, as declared by the manufacturer, extended as follows: - the lower frequency of the exclusion band is the lower frequency of the switching range, minus 5 % of the centre frequency of the switching range, or minus 10 MHz, whichever will result in the lowest frequency; - the upper frequency of the exclusion band is the upper frequency of the switching range, plus 5 % of the centre frequency of the switching range, or plus 10 MHz, which ever will result in the highest frequency. The switching range is the maximum frequency range over which the receiver can be operated without reprogramming or realignment. NOTE: The receiver exclusion band range aligns with the blocking test range Transmitter exclusion band The exclusion band for transmitters extends ±25 khz from the nominal operating frequency of the transmitter. However for TETRA equipment, the exclusion band for transmitters extends ±50 khz from the nominal operating frequency of the transmitter. 4.4 Narrow band responses of receivers The provision of, clause 4.4 shall apply. 4.5 Normal test modulation General The manufacturer may have to supply the test modulation/demodulation equipment. The test signal generator (modulation) shall be able to produce a continuous stream of data or a repetitive message. The test signal receiver (de-modulator) shall be, where appropriate, able to produce a readout of Bit Error Ratio (BER) of a continuous data stream or a repetitive readout of message acceptance.

10 10 EN V2.1.1 ( ) Analogue speech equipment Angle modulated equipment - the receiver wanted input signal shall be set to the nominal frequency of the receiver modulated with a sinusoidal audio frequency of Hz to a deviation of 60 % peak system; - the transmitter of the EUT shall be modulated with a sinusoidal audio frequency of Hz at a deviation of 60 % peak system deviation Non-angle modulated equipment - the receiver wanted input signal shall be set to the nominal frequency of the receiver suitably modulated with a sinusoidal audio frequency of Hz, which represents normal operation; - the transmitter of the EUT shall be suitably modulated with a sinusoidal audio frequency of Hz, which represents normal operation; - details concerning the modulation used shall be recorded in the test report Digital speech equipment - the receiver wanted input signal shall be set to the nominal frequency of the receiver modulated with a test signal specified by the manufacturer which represents normal operation which is in accordance with the appropriate radio product standard; - the transmitter shall be modulated with a test signal which represents normal operation as specified by the manufacturer which is in accordance with the appropriate radio product standard; - the manufacturer may have to supply the test modulation/de-modulation equipment; - details concerning the modulation used shall be recorded in the test report Non-speech equipment (data, specific response, etc.) - the receiver wanted input signal shall be set to the nominal frequency of the receiver modulated with a test signal specified by the manufacturer which represents normal operation which is in accordance with the appropriate radio product standard; - the transmitter shall be modulated with a test signal which represents normal operation as specified by the manufacturer which is in accordance with the appropriate radio product standard; - the manufacturer may have to supply the test modulation/de-modulation equipment; - details concerning the modulation used shall be recorded in the test report TETRA equipment The receiver wanted input signal shall be set to a frequency near to the middle of the operating band of the receiver modulated with one of the test signals listed below, the transmitter shall be set to a frequency near to the middle of the operating band of the transmitter modulated with one of the test signals listed below: - for equipment capable of speech operation, a speech traffic channel (TETRA TCH/S) in accordance with EN [3] representing a Hz tone at a level of 17 db below peak level; - for non-speech V+D or DMO equipment, a TCH/7.2 test signal in accordance with EN [4] or EN [5] or EN [2]; - for non-speech V+D or DMO equipment, a SCH/F test signal in accordance with EN [4] or EN [5] or EN [2]; - for non-speech PDO equipment, a NBCH test signal in accordance with EN [2];

11 11 EN V2.1.1 ( ) - for equipment capable of speech operation speech traffic channel (TETRA TCH/S) in accordance with EN [3] representing silence; - for speech and/or data equipment connected to ancillary equipment intended for data operation, or connected to ancillary equipment which can be directly connected to a data application, the method of BER or MER measurement shall be agreed between the test house and the manufacturer. 5 Performance assessment 5.1 General The provision of, clause 5.1 shall apply. 5.2 Equipment which can provide a continuous communications link The provision of, clause 5.2 shall apply. 5.3 Equipment which does not provide a continuous communications link The provision of, clause 5.3 shall apply. 5.4 Ancillary equipment The provision of, clause 5.4 shall apply. 5.5 Equipment classification The provision of, clause 5.5 shall apply. 5.6 Performance assessment of equipment providing an audio path Introduction The audio performance shall be evaluated using either the audio breakthrough method described in clause or the audio distortion method described in clause Assessment of audio path using the audio breakthrough method This test only applies to equipment, which contains audio capability. The audio paths shall be enabled. A communication link shall be set up with a suitable TETRA transceiver system simulator, or test set (hereafter called "the test system"). The wanted RF signals to be applied should be agreed between the test house and the manufacturer. When the EUT is required to be in the transmit/receive mode, the following conditions shall be met: - the EUT shall be set to operate at maximum transmit power;

12 12 EN V2.1.1 ( ) - prior to the test sequence, the reference level of the speech output signal on both the downlink and uplink shall be recorded on the test instrumentation, as shown in figure 2. The reference level shall be equivalent to 0 dbpa at Hz at the Ear Reference Point (ERP), or +5,0 dbpa at the loudspeaker for the downlink and -5 dbpa at Hz at the Mouth Reference Point (MRP), or the microphone for the uplink. The nominal acoustic test levels may need to be adapted for different types of TETRA equipment and for different acoustic test arrangements; - the level of the output signal from the EUT's downlink speech channel at the mobile or portable's ear piece shall be assessed by measuring the Sound Pressure Level (SPL) as shown in figure 1; - the level of the recovered audio output signal of the test system from the EUT's uplink speech channel shall be measured. Pick up of extraneous background noise by the EUT's microphone shall be minimized. Absorber lined test chamber Audio output Test system Audio level meter BPF CF = 1 khz BW = 200 Hz EMC test signal Radio link ERP tube MRP seal EUT ERP = Ear Reference Point MRP = Mouth Reference Point Transducer Audio level meter BPF CF = 1 khz BW = 200 Hz NOTE: In the case of a mobile equipment the ERP may be the loudspeaker, and the MRP the microphone. Figure 1: Audio breakthrough measurement, test set-up Absorber lined test chamber Test system Audio level meter BPF CF = 1 khz BW = 200 Hz Radio link Hz test source ERP tube 0 dbpa MRP -5 dbpa EUT 1020 Hz test source ERP = Ear Reference Point Transducer Audio level meter BPF CF = 1 khz BW = 200 Hz MRP = Mouth Reference Point NOTE 1: The EUT is in position during calibration of the uplink, but not during calibration of the downlink. NOTE 2: Where the EUT has a loudspeaker the reference level shall be equivalent to +5,0 dbpa at Hz. Figure 2: Audio breakthrough measurement, calibration set-up

13 13 EN V2.1.1 ( ) Assessment of audio path using the audio distortion method This test only applies to equipment, which contains audio capability. The audio paths shall be enabled. A communication link loop-back shall be set up through a suitable TETRA test system. The wanted RF signals to be applied should be agreed between the test house and the manufacturer: - the EUT shall be set to operate at maximum transmit power; - a link between the EUT and the test system is established. In the test system the received uplink signal from the EUT is looped back and returned to the EUT as a downlink signal. The loopback in the test system should be done keeping the looped signal in a digital format or in a way that the signal to be looped is left unchanged; - a Hz signal, at a level within the dynamic range of the microphone audio circuit, is applied at the Mouth Reference Point (MRP). The audio signal is, after loopback in the test system, picked up at the Ear Reference Point (ERP) by an audio transducer provided with a non-metallic acoustic tube. The transducer signal is feed to an audio distortion analyser located outside the test environment. Pick up of extraneous background noise by the EUT's microphone or by the transducer at the ERP shall be minimized. 6 Performance criteria 6.0 General The equipment shall meet the minimum performance criteria as specified in clauses 6.1, 6.2, 6.3 and 6.4. The establishment of the communication link at the start of the test, its maintenance and the assessment of the recovered signal are used as the performance criteria for the evaluation of the essential functions of the equipment during and after the test. If an equipment is of a specialized nature and the performance criteria specified in the table are not appropriate the manufacturer shall declare a substituted specification for an acceptable performance level or performance degradation as required by the present document. The performance specification shall be included in the test report and the product description and documentation. The equipment shall meet the minimum performance criteria as specified in clauses 6.1, 6.2, 6.3 and 6.4. A portable equipment powered by the battery in the vehicle shall fulfil the applicable requirements in for vehicular mobile equipment. A portable or mobile equipment powered by AC mains shall fulfil the applicable requirements in for base station equipment, although the tests performed are only those applicable to the input/output arrangements of the equipment, the performance criteria will remain as the origin class for the equipment. 6.1 Performance criteria for Continuous phenomena applied to Transmitters (CT) For speech equipment, the distortion of the audio signal shall be measured during each individual exposure in the test sequence and shall not exceed 25 % measured in a post detection bandwidth determined by a first order band pass filter with a 3 db bandwidth of 300 Hz to 3 khz, without the use of psophometric weighting filter. For equipment which can be measured using continuous bit streams, a bit error shall not exceed For other non-speech equipment four messages out of five or 90 % of the transmitted symbols shall be received correctly. At the conclusion of the test the EUT shall operate as intended with no loss of user control functions or stored data, and the communication link shall have been maintained during the test.

14 14 EN V2.1.1 ( ) Where the EUT is a transmitter only and can be operated in standby mode, tests shall be repeated with the EUT in this mode to ensure that unintentional transmission does not occur. 6.2 Performance criteria for Transient phenomena applied to Transmitters (TT) At the conclusion of each exposure the EUT shall operate with no user noticeable loss of the communication link. At the conclusion of the total test comprising the series of individual exposures the EUT shall operate as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link shall have been maintained during the test. Where the EUT is a transmitter only and can be operated in standby mode, tests shall be repeated with the EUT in this mode to ensure that unintentional transmission does not occur. 6.3 Performance criteria for Continuous phenomena applied to Receivers (CR) For speech equipment, the distortion of the audio signal shall be measured during each individual exposure in the test sequence and shall not exceed 25 % measured in a post detection bandwidth determined by a first order band pass filter with a 3 db bandwidth of 300 Hz to 3 khz, without the use of psophometric weighting filter. For equipment which can be measured using continuous bit streams, the bit error rate shall not exceed For other non-speech equipment four messages out of five or 90 % of the transmitted symbols shall be received correctly. At the conclusion of the test the EUT shall operate as intended with no loss of user control functions or stored data, and the communication link shall have been maintained during the test. Where the EUT is a transceiver, under no circumstances shall the transmitter operate unintentionally during the test. 6.4 Performance criteria for Transient phenomena applied to Receivers (TR) At the conclusion of each exposure the EUT shall operate with no user noticeable loss of the communication link. At the conclusion of the total test comprising the series of individual exposures the EUT shall operate as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link shall have been maintained during the test. Where the EUT is a transceiver, under no circumstances shall the transmitter operate unintentionally during the test. 6.5 Performance criteria for ancillary equipment tested on a stand alone basis The provision of, clause 6.4 shall apply.

15 15 EN V2.1.1 ( ) 7 Applicability overview 7.1 Emission General Table 1 in, contains the applicability of EMC emission measurements to the relevant ports of radio and/or associated ancillary equipment Special conditions No special conditions shall apply to Private land Mobile Radio (PMR) equipment in the scope of the present document. 7.2 Immunity General Table 2 of, contains the applicability of EMC immunity measurements to the relevant ports of radio and/or associated ancillary equipment Special conditions The following special conditions set out in table 1, relate to the immunity test methods and performance criteria used in, clause 9 apply to TETRA equipment only. For all other types of Private land Mobile Radio (PMR) equipment in the scope of the present document no special conditions apply. Table 1: Special conditions for EMC immunity tests for TETRA equipment Reference to clauses in 9.2.2: Test method; Radio frequency electromagnetic field 9.5.2: Test method Radio frequency, common mode Special product-related conditions, additional to or modifying the test conditions in, clause 9 - the test signal shall be amplitude modulated to a depth of 80 % by a sinusoidal audio signal of Hz; - for transmitters in transceivers with a non-continuous duty cycle the stepped frequency increments may be 10 % of the momentary frequency; - the test shall be carried out on one surface. The surface selected to face the source of the interference signal shall be the one anticipated by the test house to be the most susceptible. The selected surface shall be recorded in the test report. - the test signal shall be amplitude modulated to a depth of 80 % by a sinusoidal audio signal of Hz; - for transmitters in transceivers with a non-continuous duty cycle the stepped frequency increments may be 500 khz in the frequency range 150 khz to 5 MHz and 10 % frequency increment of the momentary frequency in the frequency range 5 MHz to 80 MHz.

16 16 EN V2.1.1 ( ) Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. Table A.1: Relationship between the present document and the essential requirements of Directive 2014/53/EU Harmonized Standard EN The following requirements are relevant to the presumption of conformity under the article 3.1b of Directive 2014/53/EU [i.1] Requirement Requirement Conditionality No Description Reference: U/ Clause No C Condition 1 Enclosure of ancillary equipment 8.2 of U measured on a stand alone basis 2 DC power input/output ports 8.3 of 3 AC mains power input/output ports 8.4 of 4 Harmonic current emission 8.5 of (AC mains input port) 5 Voltage fluctuations and flicker 8.6 of (AC mains input ports) 6 Wired network ports 8.7 of 7 Radio frequency electromagnetic field (80 MHz to MHz) C C C C C Only where equipment has DC power input and/or output ports with a cable length greater than 3m or from a vehicle power supply Only where equipment has AC mains power input and/or output ports Only where equipment has AC mains power input ports Only where equipment has AC mains power input ports Only where equipment has wired network ports U For TETRA equipment refer to clause of the present document. For all other types of PMR equipment refer to clause 9.2 of 8 Electrostatic discharge 9.3 of U 9 Fast transients common mode 9.4 of U 10 Radio frequency common mode U For TETRA equipment refer to clause of the present document. For all other types of PMR equipment refer to clause 9.2 of 11 Transients and surges in the vehicular environment 9.6 of 12 Voltage dips and interruptions 9.7 of 13 Surges, line to line and line to 9.8 of ground C C C Only where equipment is fitted to a vehicle power supply Only where equipment has AC mains power input ports Only where equipment has AC mains power input ports and/or wired network ports Key to columns: Requirement: No Description A unique identifier for one row of the table which may be used to identify a requirement. A textual reference to the requirement.

17 17 EN V2.1.1 ( ) Clause Number Identification of clause(s) defining the requirement in the present document unless another document is referenced explicitly. Requirement Conditionality: U/C Condition Indicates whether the requirement shall be unconditionally applicable (U) or is conditional upon the manufacturers claimed functionality of the equipment (C). Explains the conditions when the requirement shall or shall not be applicable for a requirement which is classified "conditional". Presumption of conformity stays valid only as long as a reference to the present document is maintained in the list published in the Official Journal of the European Union. Users of the present document should consult frequently the latest list published in the Official Journal of the European Union. Other Union legislation may be applicable to the product(s) falling within the scope of the present document.

18 18 EN V2.1.1 ( ) Annex B (informative): Examples of PMR equipment in the scope of the present document B.1 Introduction The provisions of the present document apply to radio and associated ancillary equipment intended for use in the land mobile service, that means to Private/Professional land Mobile Radio (PMR) equipment as set out in the following clauses. B.2 Non-integral antenna PMR equipment The present document applies in particular to angle modulated (constant envelope) radio equipment, operating on radio frequencies between 30 MHz and MHz, with channel separations of 12,5 khz, 20 khz and 25 khz, and associated ancillary equipment. It applies to: - PMR equipment primarily intended for transmission of analogue speech, as defined in ETS [i.4]; - PMR equipment and the non-speech part of combined speech/non-speech radio equipment, intended for transmission of non-speech information to initiate a specific response in the receiver, as defined in I-ETS [i.5]. - digital and combined analogue and digital PMR equipment and parts thereof, intended for transmission of data and/or speech as defined in EN [i.6]. B.3 Integral antenna PMR equipment The present document applies also to angle modulated (constant envelope) radio equipment, operating on radio frequencies between 30 MHz and MHz, with channel separations of 12,5 khz, 20 khz and 25 khz, and associated ancillary equipment. It applies to: - PMR equipment intended for transmission of analogue speech, as defined in EN [i.7]; - PMR equipment and the non-speech part of combined speech/non-speech radio equipment, intended for transmission of non-speech information to initiate a specific response in the receiver, as defined in EN [i.8]; - digital and combined analogue and digital PMR equipment and parts thereof, intended for transmission of data and/or speech as defined in EN [i.9]. B.4 Narrowband channel non-integral PMR equipment The present document applies also to radio equipment, operating on radio frequencies between 30 MHz and 3 GHz, with narrow channel separations (less than 10 khz, and associated ancillary equipment). It applies to: - PMR equipment intended for transmission of digitized speech and/or data, with narrow channel separation (less than 10 khz and permitted by CEPT), and using constant or non-constant envelope type of modulation as defined in EN [i.10].

19 19 EN V2.1.1 ( ) B.5 Mobile, base station, and portable equipment of TErrestrial Trunked Radio (TETRA) equipment The present document applies to all TErrestrial Trunked Radio (TETRA) radio equipment covered by EN [i.2]. This includes the following categories of equipment: - Mobile Station (MS); - Base Station (BS); - Direct Mode Mobile Station (DM-MS); - Dual Watch Mobile Station (DW-MS); - Direct Mode GATEway (DM-GATE); - Direct Mode REPeater (DM-REP); - Direct Mode REPeater/GATEway (DM-REP/GATE); - Trunked MOde REPeater (TMO-REP); - portable equipment of TErrestrial Trunked Radio (TETRA) radiocommunications systems.

20 20 EN V2.1.1 ( ) Annex C (informative): Bibliography EN : "ElectroMagnetic Compatibility and Radio Spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Part 1: Technical characteristics and methods of measurement". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and speech) and having an antenna connector; Part 1: Technical characteristics and methods of measurement". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and speech) and having an antenna connector; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive". EN : "ElectroMagnetic Compatibility and Radio Spectrum Matters (ERM); Land Mobile Service; Radio equipment transmitting signals to initiate a specific response in the receiver". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 1: Technical characteristics and methods of measurement". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service (RP 02); Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Part 1: Technical characteristics and methods of measurement". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service (RP 02); Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna; Part 1: Technical characteristics and test conditions". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrowband channels and having an antenna connector; Part 1: Technical characteristics and methods of measurement". EN : "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrowband channels and having an antenna connector; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive".

21 21 EN V2.1.1 ( ) History Document history V1.2.1 August 2000 Publication V1.3.1 August 2002 Publication V2.1.0 April 2016 EN Approval Procedure AP : to V2.1.1 November 2016 Publication

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 301 489-18 V1.3.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

Summary 18/03/ :27:42. Differences exist between documents. Old Document: en_ v010501p 17 pages (97 KB) 18/03/ :27:35

Summary 18/03/ :27:42. Differences exist between documents. Old Document: en_ v010501p 17 pages (97 KB) 18/03/ :27:35 Summary 18/03/2016 16:27:42 Differences exist between documents. New Document: en_30067602v020101p 16 pages (156 KB) 18/03/2016 16:27:36 Used to display results. Old Document: en_30067602v010501p 17 pages

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-6 V1.2.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 300 422-2 V1.3.1 (2011-08) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range; Part 2: Harmonized

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 301 489-17 V1.2.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

Final draft ETSI EG V1.1.0 ( )

Final draft ETSI EG V1.1.0 ( ) Final draft EG 203 367 V1.1.0 (2016-03) GUIDE Guide to the application of harmonised standards covering articles 3.1b and 3.2 of the Directive 2014/53/EU (RED) to multi-radio and combined radio and non-radio

More information

ETSI EN V1.1.1 ( ) Harmonized European Standard (Telecommunications series)

ETSI EN V1.1.1 ( ) Harmonized European Standard (Telecommunications series) EN 302 617-2 V1.1.1 (2010-10) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and

More information

Draft ETSI EN V3.2.0 ( )

Draft ETSI EN V3.2.0 ( ) Draft EN 301 489-17 V3.2.0 (2017-03) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Broadband Data Transmission

More information

ETSI EN V1.2.1 ( )

ETSI EN V1.2.1 ( ) EN 300 113-2 V1.2.1 (2002-04) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended

More information

ETSI EN V1.2.1 ( ) Harmonized European Standard

ETSI EN V1.2.1 ( ) Harmonized European Standard EN 302 372-2 V1.2.1 (2011-02) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Equipment for Detection and Movement; Tanks Level Probing

More information

ETSI EN V1.1.2 ( ) Harmonized European Standard

ETSI EN V1.1.2 ( ) Harmonized European Standard EN 302 729-2 V1.1.2 (2011-05) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Level Probing Radar (LPR) equipment operating in the

More information

Draft ETSI EN V3.2.0 ( )

Draft ETSI EN V3.2.0 ( ) Draft EN 301 489-4 V3.2.0 (2017-03) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 301 489-26 V1.1.1 (2001-09) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 264 V2.1.1 (2017-05) HARMONISED EUROPEAN STANDARD Short Range Devices; Transport and Traffic Telematics (TTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard

More information

Draft ETSI EN V2.2.0 ( )

Draft ETSI EN V2.2.0 ( ) Draft EN 301 489-15 V2.2.0 (2017-03) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 15: Specific conditions for commercially available

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 471-2 V1.1.1 (2001-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Rules for Access and

More information

ETSI EN V3.1.1 ( )

ETSI EN V3.1.1 ( ) EN 301 489-17 V3.1.1 (2017-02) HARMONISED EUROPEAN STANDARD Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 219-2 V1.1.1 (2001-03) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment transmitting

More information

Final draft ETSI EN V1.1.1 ( )

Final draft ETSI EN V1.1.1 ( ) Final draft EN 302 291-2 V1.1.1 (2005-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Close

More information

ETSI EN V2.2.1 ( )

ETSI EN V2.2.1 ( ) EN 301 843-1 V2.2.1 (2017-11) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard for electromagnetic compatibility; Part

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 300 341-2 V1.1.1 (2000-12) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile service (RP 02); Radio equipment

More information

DraftETSI EN V1.1.1 ( )

DraftETSI EN V1.1.1 ( ) Draft EN 301 489-3 V1.1.1 (1999-12) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)

More information

ETSI EN V ( )

ETSI EN V ( ) EN 301 908-11 V11.1.2 (2017-01) HARMONISED EUROPEAN STANDARD IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct

More information

ETSI TS V1.1.1 ( )

ETSI TS V1.1.1 ( ) TS 100 220-1 V1.1.1 (1999-10) Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRDs); Measurement Specification for Wideband Transmitter Stability

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 119-4 V2.1.1 (2004-09) European Standard (Telecommunications series) Environmental Engineering (EE); European telecommunication standard for equipment practice; Part 4: Engineering requirements

More information

Draft ETSI EN V1.1.1 ( )

Draft ETSI EN V1.1.1 ( ) Draft EN 302 245-1 V1.1.1 (2004-05) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Transmitting equipment for the Digital Radio Mondiale (DRM)

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 018 V2.1.1 (2017-04) HARMONISED EUROPEAN STANDARD Transmitting equipment for the Frequency Modulated (FM) sound broadcasting service; Harmonised Standard covering the essential requirements of article

More information

ETSI EN V6.1.1 ( )

ETSI EN V6.1.1 ( ) EN 301 908-21 V6.1.1 (2016-05) HARMONISED EUROPEAN STANDARD IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD

More information

Draft ETSI EN V2.2.0 ( )

Draft ETSI EN V2.2.0 ( ) Draft EN 301 489-50 V2.2.0 (2017-03) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 50: Specific conditions for Cellular Communication

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 300 086 V2.1.2 (2016-08) HARMONISED EUROPEAN STANDARD Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Harmonised Standard covering

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 301 489-50 V2.1.1 (2017-02) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 50: Specific conditions for Cellular Communication Base Station

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 303 039 V2.1.2 (2016-10) HARMONISED EUROPEAN STANDARD Land Mobile Service; Multichannel transmitter specification for the PMR Service; Harmonised Standard covering the essential requirements of article

More information

Summary 04/08/ :05:07. Differences exist between documents. Old Document: en_ v010101p 39 pages (241 KB) 04/08/ :04:53

Summary 04/08/ :05:07. Differences exist between documents. Old Document: en_ v010101p 39 pages (241 KB) 04/08/ :04:53 Summary 04/08/2016 11:05:07 Differences exist between documents. New Document: en_30257403v020101p 42 pages (270 KB) 04/08/2016 11:04:53 Used to display results. Old Document: en_30257403v010101p 39 pages

More information

ETSI EN V ( )

ETSI EN V ( ) EN 300 609-4 V10.2.1 (2012-11) Harmonized European Standard Global System for Mobile communications (GSM); Part 4: Harmonized EN for GSM Repeaters covering the essential requirements of article 3.2 of

More information

ETSI TS V1.2.1 ( ) Technical Specification. Terrestrial Trunked Radio (TETRA); RF Sensitive Area Mode

ETSI TS V1.2.1 ( ) Technical Specification. Terrestrial Trunked Radio (TETRA); RF Sensitive Area Mode TS 101 975 V1.2.1 (2007-07) Technical Specification Terrestrial Trunked Radio (TETRA); RF Sensitive Area Mode 2 TS 101 975 V1.2.1 (2007-07) Reference RTS/TETRA-01069 Keywords TETRA, radio, MS 650 Route

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 330 V2.1.1 (2017-02) HARMONISED EUROPEAN STANDARD Short Range Devices (SRD); Radio equipment in the frequency range 9 khz to 25 MHz and inductive loop systems in the frequency range 9 khz to 30

More information

ETSI ES V1.2.1 ( )

ETSI ES V1.2.1 ( ) ES 201 235-2 V1.2.1 (2002-03) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 2: Transmitters 2 ES 201 235-2 V1.2.1 (2002-03) Reference

More information

ETSI EN V2.2.1 ( )

ETSI EN V2.2.1 ( ) EN 302 054 V2.2.1 (2018-02) HARMONISED EUROPEAN STANDARD Meteorological Aids (Met Aids); Radiosondes to be used in the 400,15 MHz to 406 MHz frequency range with power levels ranging up to 200 mw; Harmonised

More information

ETSI EN V1.2.1 ( ) European Standard (Telecommunications series)

ETSI EN V1.2.1 ( ) European Standard (Telecommunications series) EN 301 783-1 V1.2.1 (2010-07) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Commercially available amateur radio equipment;

More information

ETSI TS V8.7.0 ( ) Technical Specification

ETSI TS V8.7.0 ( ) Technical Specification TS 136 214 V8.7.0 (2009-10) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Physical layer - Measurements (3GPP TS 36.214 version 8.7.0 Release 8) 1 TS 136 214 V8.7.0

More information

Summary 04/08/ :02:08. Differences exist between documents. Old Document: en_301721v010201p 36 pages (187 KB) 04/08/ :01:51

Summary 04/08/ :02:08. Differences exist between documents. Old Document: en_301721v010201p 36 pages (187 KB) 04/08/ :01:51 Summary 04/08/2016 12:02:08 Differences exist between documents. New Document: en_301721v020101p 39 pages (231 KB) 04/08/2016 12:01:51 Used to display results. Old Document: en_301721v010201p 36 pages

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 303 405 V1.1.1 (2017-05) HARMONISED EUROPEAN STANDARD Land Mobile Service; Analogue and Digital PMR446 Equipment; Harmonised Standard covering the essential requirements of article 3.2 of Directive

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 303 417 V1.1.1 (2017-09) HARMONISED EUROPEAN STANDARD Wireless power transmission systems, using technologies other than radio frequency beam in the 19-21 khz, 59-61 khz, 79-90 khz, 100-300 khz, 6 765-6

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 502 V2.1.1 (2017-03) HARMONISED EUROPEAN STANDARD Wireless Access Networks (BRANSystems (WAS); 5,8 GHz fixed broadband data transmitting systems; Harmonized ENHarmonised Standard covering the essential

More information

Draft ETSI EN V1.3.1 ( )

Draft ETSI EN V1.3.1 ( ) Draft EN 300 659-2 V1.3.1 (2000-09) European Standard (Telecommunications series) Access and Terminals (AT); Analogue access to the Public Switched Telephone Network (PSTN); Subscriber line protocol over

More information

Draft ETSI EN V2.1.0 ( )

Draft ETSI EN V2.1.0 ( ) Draft EN 300 718-1 V2.1.0 (2017-09) HARMONISED EUROPEAN STANDARD Avalanche Beacons operating at 457 khz; Transmitter-receiver systems; Part 1: Harmonised Standard for access to radio spectrum 2 Draft EN

More information

Text Comparison. Documents Compared en_301442v010101p.pdf. en_301442v010201p.pdf

Text Comparison. Documents Compared en_301442v010101p.pdf. en_301442v010201p.pdf Text Comparison Documents Compared en_301442v010101p.pdf en_301442v010201p.pdf Summary 2470 word(s) added 2471 word(s) deleted 11796 word(s) matched 77 block(s) matched To see where the changes are, please

More information

ETSI TS V8.0.0 ( ) Technical Specification

ETSI TS V8.0.0 ( ) Technical Specification TS 136 106 V8.0.0 (2009-01) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (); FDD repeater radio transmission and reception (3GPP TS 36.106 version 8.0.0 Release 8) 1 TS 136 106

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 301 357 V2.1.1 (2017-06) HARMONISED EUROPEAN STANDARD Cordless audio devices in the range 25 MHz to 2 000 MHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 300 224-1 V1.3.1 (2001-01) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); On-site paging service; Part 1: Technical and functional characteristics,

More information

ETSI EG V1.1.1 ( )

ETSI EG V1.1.1 ( ) EG 202 118 V1.1.1 (2003-05) Guide Services and Protocols for Advanced Networks (SPAN); The structure of the TETRA numbering resource, interworking and high level policy for administration 2 EG 202 118

More information

TECHNICAL REPORT Electromagnetic compatibility and Radio spectrum Matters (ERM); Impact of CENELEC EN on ETSI EMC Standards

TECHNICAL REPORT Electromagnetic compatibility and Radio spectrum Matters (ERM); Impact of CENELEC EN on ETSI EMC Standards TR 103 400 V1.1.1 (2017-03) TECHNICL REPORT Electromagnetic compatibility and Radio spectrum Matters (ERM); Impact of EN 55035 on EMC Standards 2 TR 103 400 V1.1.1 (2017-03) Reference DTR/ERM-EMC-318 Keywords

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 300 328-1 V1.3.1 (2001-12) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating

More information

ETSI TR V1.1.1 ( )

ETSI TR V1.1.1 ( ) TR 102 070-1 V1.1.1 (2002-07) Technical Report Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide to the application of harmonized standards to multi-radio and combined radio and non-radio

More information

Final draft ETSI ES V1.3.1 ( )

Final draft ETSI ES V1.3.1 ( ) Final draft ES 201 235-4 V1.3.1 (2006-01) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 4: Transmitters and Receivers for use in

More information

ETSI ES V1.1.1 ( )

ETSI ES V1.1.1 ( ) ES 201 729 V1.1.1 (2000-02) Standard Public Switched Telephone Network (PSTN); 2-wire analogue voice band switched interfaces; Timed break recall (register recall); Specific requirements for terminals

More information

ETSI TS V ( )

ETSI TS V ( ) TS 126 171 V14.0.0 (2017-04) TECHNICAL SPECIFICATION Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); LTE; Speech codec speech processing

More information

Summary 04/08/ :53:06. Differences exist between documents. Old Document: en_301441v010101p 47 pages (209 KB) 04/08/ :52:48

Summary 04/08/ :53:06. Differences exist between documents. Old Document: en_301441v010101p 47 pages (209 KB) 04/08/ :52:48 Summary 04/08/2016 11:53:06 Differences exist between documents. New Document: en_301441v020101p 49 pages (279 KB) 04/08/2016 11:52:48 Used to display results. Old Document: en_301441v010101p 47 pages

More information

EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4: Antennas

EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4: Antennas Draft EN 32 217-4 V2..3 (216-6) EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4: Antennas 2 Draft EN 32 217-4 V2..3 (216-6) Reference

More information

Draft ETSI EN V1.4.1 ( )

Draft ETSI EN V1.4.1 ( ) Draft EN 300 296-1 V1.4.1 (2012-07) European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for

More information

ETSI EN V1.1.2 ( )

ETSI EN V1.1.2 ( ) EN 303 348 V1.1.2 (2017-07) HARMONISED EUROPEAN STANDARD Induction loop systems intended to assist the hearing impaired in the frequency range 10 Hz to 9 khz; Harmonised Standard covering the essential

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 440 V2.1.1 (2017-03) HARMONISED EUROPEAN STANDARD Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Harmonised Standard covering the essential requirements

More information

ETSI TS V9.3.0 ( ) Technical Specification

ETSI TS V9.3.0 ( ) Technical Specification TS 136 106 V9.3.0 (2011-01) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (); FDD repeater radio transmission and reception (3GPP TS 36.106 version 9.3.0 Release 9) 1 TS 136 106

More information

ETSI EN V2.2.1 ( )

ETSI EN V2.2.1 ( ) EN 300 698 V2.2.1 (2017-10) HARMONISED EUROPEAN STANDARD Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard

More information

ETSI EN V3.1.1 ( )

ETSI EN V3.1.1 ( ) EN 302 217-2 V3.1.1 (2017-05) HARMONISED EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency

More information

Draft ETSI EN V1.1.1 ( )

Draft ETSI EN V1.1.1 ( ) Draft EN 302 608 V1.1.1 (2007-12) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment for

More information

ETSI EN V2.2.1 ( )

ETSI EN V2.2.1 ( ) EN 301 025 V2.2.1 (2017-03) HARMONISED EUROPEAN STANDARD VHF radiotelephone equipment for general communications and associated equipment for Class "D" Digital Selective Calling (DSC); Harmonised Standard

More information

DraftETSI EN V1.1.1 ( )

DraftETSI EN V1.1.1 ( ) Draft EN 301 893 V1.1.1 (2001-01) Candidate Harmonized European Standard (Telecommunications series) Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Harmonized EN covering essential requirements

More information

ETSI EN V2.1.1 ( ) European Standard (Telecommunications series)

ETSI EN V2.1.1 ( ) European Standard (Telecommunications series) EN 302 500-1 V2.1.1 (2010-10) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra WideBand (UWB) technology;

More information

ETSI TS V8.2.0 ( ) Technical Specification

ETSI TS V8.2.0 ( ) Technical Specification TS 136 306 V8.2.0 (2008-11) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) radio access capabilities (3GPP TS 36.306 version 8.2.0 Release 8) 1 TS

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 208-1 V2.1.1 (2015-02) EUROPEAN STANDARD Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power

More information

ETSI ES V1.2.1 ( )

ETSI ES V1.2.1 ( ) ES 201 235-4 V1.2.1 (2002-03) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 4: Transmitters and Receivers for use in Terminal Equipment

More information

Draft ETSI EN V3.0.8 ( )

Draft ETSI EN V3.0.8 ( ) Draft EN 302 217-2 V3.0.8 (2016-06) HARMONISED EUROPEAN STANDARD Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 302 480 V2.1.2 (2017-02) HARMONISED EUROPEAN STANDARD Mobile Communication On Board Aircraft (MCOBA) systems; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 220-1 V2.1.1 (2006-04) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the

More information

ETSI EN V ( )

ETSI EN V ( ) EN 301 908-2 V11.1.2 (2017-08) HARMONISED EUROPEAN STANDARD IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 2: CDMA Direct Spread

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 302 296 V2.1.1 (2017-06) HARMONISED EUROPEAN STANDARD Digital Terrestrial TV Transmitters; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU 2 EN 302 296

More information

Draft ETSI EN V1.1.0 ( )

Draft ETSI EN V1.1.0 ( ) Draft EN 303 348 V1.1.0 (2016-02) HARMONISED EUROPEAN STANDARD Induction loop systems intended to assist the hearing impaired in the frequency range 10 Hz to 9 khz; Harmonised Standard covering the essential

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 303 316 V1.1.1 (2017-10) HARMONISED EUROPEAN STANDARD Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Beamforming

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 300 220-1 V1.3.1 (2000-09) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the

More information

Draft ETSI EN V1.1.1 ( )

Draft ETSI EN V1.1.1 ( ) Draft EN 302 291-1 V1.1.1 (2004-07) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Close Range Inductive Data Communication

More information

Draft ETSI EN V0.1.7 ( )

Draft ETSI EN V0.1.7 ( ) Draft EN 303 084 V0.1.7 (2013-01) Harmonized European Standard Ground Based Augmentation System (GBAS) VHF ground-air Data Broadcast (VDB); Technical characteristics and methods of measurement for ground-based

More information

ETSI TS V1.1.1 ( )

ETSI TS V1.1.1 ( ) TS 103 060 V1.1.1 (2013-09) Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Method for a harmonized definition of Duty Cycle Template

More information

ETSI EN V1.1.1 ( )

ETSI EN V1.1.1 ( ) EN 302 208-1 V1.1.1 (2004-09) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency Identification Equipment operating in the band

More information

ETSI EN V1.3.1 ( )

ETSI EN V1.3.1 ( ) EN 302 065-1 V1.3.1 (2014-04) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonized EN

More information

EN V1.6.3 ( )

EN V1.6.3 ( ) European Standard (Telecommunications series) Equipment practice; Engineering requirements for outdoor enclosures; Part 1: Equipped enclosures 2 Reference DEN/EE-00001-1 (ato90k20.pdf) Keywords equipment

More information

Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 10: Supplementary services stage 1; Sub-part 22: Dynamic Group Number Assignment (DGNA)

Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 10: Supplementary services stage 1; Sub-part 22: Dynamic Group Number Assignment (DGNA) Final draft EN 300 392-10-22 V1.2.1 (2001-09) European Standard (Telecommunications series) Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 10: Supplementary services stage 1; Sub-part 22:

More information

ETSI TS V8.3.0 ( ) Technical Specification

ETSI TS V8.3.0 ( ) Technical Specification TS 136 143 V8.3.0 (2010-02) Technical Specification LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 8.3.0 Release 8) 1 TS 136 143 V8.3.0

More information

ETSI TS V1.3.1 ( )

ETSI TS V1.3.1 ( ) TS 102 121 V1.3.1 (2014-07) TECHNICAL SPECIFICATION Environmental Engineering (EE); Power distribution to telecommunications and datacom (ICT) 2 TS 102 121 V1.3.1 (2014-07) Reference RTS/EE-02041 Keywords

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 300 422-1 V2.1.2 (2017-01) HARMONISED EUROPEAN STANDARD Wireless Microphones; Audio PMSE up to 3 GHz; Part 1: Class A Receivers; Harmonised Standard covering the essential requirements of article 3.2

More information

Draft ETSI EN V1.1.1 ( )

Draft ETSI EN V1.1.1 ( ) Draft EN 301 449 V1.1.1 (2005-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Harmonized EN for CDMA spread spectrum

More information

Final draft ETSI EN V1.4.1 ( )

Final draft ETSI EN V1.4.1 ( ) Final draft EN 302 217-4-1 V1.4.1 (2009-09) European Standard (Telecommunications series) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4-1: System-dependent

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 422-4 V2.1.1 (2017-05) HARMONISED EUROPEAN STANDARD Wireless Microphones; Audio PMSE up to 3 GHz; Part 4: Assistive Listening Devices including personal sound amplifiers and inductive systems up

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 422-2 V2.1.1 (2017-02) HARMONISED EUROPEAN STANDARD Wireless Microphones; Audio PMSE up to 3 GHz; Part 2: Class B Receivers; Harmonised Standard covering the essential requirements of article 3.2

More information

ETSI EN V2.1.2 ( )

ETSI EN V2.1.2 ( ) EN 301 428 V2.1.2 (2017-05) HARMONISED EUROPEAN STANDARD Satellite Earth Stations and Systems (SES); Harmonised Standard for Very Small Aperture Terminal (VSAT); Transmit-only, transmit/receive or receive-only

More information

ETSI TS V ( )

ETSI TS V ( ) TS 135 232 V12.1.0 (2014-10) TECHNICAL SPECIFICATION Universal Mobile Telecommunications System (UMTS); LTE; Specification of the TUAK algorithm set: A second example algorithm set for the 3GPP authentication

More information

ETSI EN V2.1.1 ( )

ETSI EN V2.1.1 ( ) EN 300 674-2-1 V2.1.1 (2016-09) HARMONISED EUROPEAN STANDARD Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating

More information

ETSI TS V9.1.1 ( ) Technical Specification

ETSI TS V9.1.1 ( ) Technical Specification TS 136 410 V9.1.1 (2011-05) Technical Specification LTE; Evolved Universal Terrestrial Radio Access Network (E-UTRAN); S1 general aspects and principles (3GPP TS 36.410 version 9.1.1 Release 9) 1 TS 136

More information

ETSI EN V1.3.2 ( ) European Standard (Telecommunications series)

ETSI EN V1.3.2 ( ) European Standard (Telecommunications series) EN 300 422-1 V1.3.2 (2008-03) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range;

More information

Final draft ETSI EN V1.1.0 ( )

Final draft ETSI EN V1.1.0 ( ) Final draft EN 302 567 V1.1.0 (2009-01) Harmonized European Standard (Telecommunications series) Broadband Radio Access Networks (BRAN); 60 GHz Multiple-Gigabit WAS/RLAN Systems; Harmonized EN covering

More information